Search Results

Search found 8892 results on 356 pages for 'disk druid'.

Page 295/356 | < Previous Page | 291 292 293 294 295 296 297 298 299 300 301 302  | Next Page >

  • Help recovering broken OS (permissions issue)

    - by Guandalino
    (At the bottom there is an important update.) I was doing experiments in order to backup a remote account to my local system, Ubuntu 12.04 LTS. I'm not confident with duplicity and probably, due to wrong syntax, some local files have been replaced with remote files. This is just a supposition, I'm not sure this is the real cause of OS corruption. The corruption happened after experimenting with backups, so I think I did something wrong at this regard. I was aware there was a problem when I tried to access a command using sudo: $ sudo ls sudo: unable to open /etc/sudoers: Permission denied sudo: no valid sudoers sources found, quitting sudo: unable to initialize policy plugin This is how /etc/sudoers looks like: $ ls -ald /etc/sudoers -r--r----- 1 root root 788 Oct 2 18:30 /etc/sudoers At this point I tried to reboot and now this is the message I get: The system is running in low graphics mode. Your screen, graphics card and input device settings could not be detected correctly. You will need to configure these yourself. I tried to follow the wizard to configure these settings, but without luck (the system prevents me going on when I press "Next"). The thing that makes me a bit less worried is that all the data on the disk seems readable and I'm able to access them using a live cd. I run memtest and RAM seems to be OK. Do you have any idea about how to recover my system? I'm very glad to provide further information, just let me know what info could be helpful. UPDATE. The issue is about wrong permissions and this is how I discovered: I mounted the root partition of the broken OS on /mnt/broken/ (live CD) and did ls /mnt/broken/. I got a permission denied error, while I expected to have the directory listing. I had to do sudo ls /mnt/broken/ and this worked. Thus without having root permission via sudo it's impossible to access the root of broken os. The current output of ls -ld /mnt/broken/ is: drwxr-x--- 29 1000 812 4096 2012-12-08 21:58 /mnt/broken Any thoughts on how to restore the old (working) set of permissions?

    Read the article

  • Problem with DualBooting Ubuntu 13.10 and Win7

    - by VinArrow
    this is my first post here on AskUbuntu, not first time using it though. I wanted to install Ubuntu 13.10 on my PC to have all my work stuff there and leave Win7 for gaming. So i did my research on how to Dual Boot when you already have Win7 installed, here are the steps i took Used Disk Management on Win7 and shrunk that partition, leaving 80GB free for Ubuntu. Made a Bootable pendrive following the instructions on Ubuntu`s website. During the installation steps there was supposed to be a Install alongside Win7, but there wasnt, so i chose Something else. Everything was fine and i was able to install Ubuntu no problem on my unallocated 80GB partition (76GB Ubuntu + 4GB swap) There was a prompt for me to restart my PC and so I did expecting to see the dual boot screen (grub right?) Now, when i restarted my PC, Grub never showed up and it booted straight to Windows. Then I did some more research and found out that that could happen. Tried three things then Plugging in bootable pendrive again and selected Try Ubuntu without installing. Then i followed some instructions found here (How can I repair grub? (How to get Ubuntu back after installing Windows?)) and i could chroot into my Ubuntu install just fine. Repaired grub as instructed on that link, restarted the PC and booted straight into Win7 again. Again, used the bootable pen drive to Try Ubuntu... and used the Boot-repair tool (recommended repair). Again, booted straight into Win7. Lastly, i installed easyBCD on my Win7 and made a new entry for Ubuntu (Linux/BSD). When i rebooted the PC, there was the option to choose between Win7 and Linux, chose linux and it didnt work, taking me straight to a command line-like enviroment that read Minimum bash like scripting or something, as if I didn`t have a Linux OS installed. So, I thought I`d try and repair my Ubuntu install. And during the Installation method step there was the choice to install alongside Ubuntu 13.10! and that right there drove me crazy. Here is a screenshot of gparted showing how things are set up now http://imageshack.us/f/801/77u3.png/ Notice on the left-hand side how i can access my installation files just fine. sdb1- win7 reserved space, sdb2- win7 OS, sdb3- 76GB ubuntu install, sdb5- 4GB swap area. Does anyone know why my Ubuntu 13.10 is not being recognized? and what should I do to get it working? Thanks and sorry for the long read and bad english! (BIOS = legacy)

    Read the article

  • IPv6, isn't it just a few extra bits?

    - by rclewis
    It's always an interesting task, to try and explain what you do to family and friends. I have described IPv6 as the "Next Generation Internet"  or "Second Internet" but the hollow expressions on my kids faces scream for the instant relief of the latest video game.  Never one to give up easily, I have formulated a new example - the Post Office... Similar to the Post Office the Internet delivers mail and packages based on addresses. As the number of residences, businesses, and delivery locations increased, the 5 digit ZIP Code (Washington, DC 20005) was expanded to ZIP+4  allowing for more precise delivery points (Postmaster General, Washington, DC 20260-3100). Ah, if only computers were as simple.  IPv6 isn't an add-on or expansion of the existing IPv4 Addressing, it is a new addressing model which will allow the internet to grow from a single computer in the basement of a university or your parents kitchen table, to support the multitude of smart phones, smart TV's, tablets, dvr's, and disk players, all clambering to connect for information. Unfortunetly there are only a finite number of IPv4 public addresses left, and those are being consumed at an ever increasing rate. Few people could have predicted the explosive growth of the internet or the shortage of IPv4 addresses we now face - but there is a "Plan B" and that is the vastly larger address space of IPv6.  Many in the industry have labeled this a "business continuity" problem,  when in fact most companies will be able to continue conducting business once they run out of existing IPv4 Addresses. The problem is really a Customer Continuity problem, how will businesses communicate with existing customers and reach new customers online who's only option is to adopt IPv6 when IPv4 is depleted? Perhaps a first step is publishing a blog that is also accessible via IPv6, it's just a few extra bits. Join us for the Oracle OpenWorld 2012 Session:   Navigating IPv6 @ Oracle Thursday, Oct. 4th 2:15PM - 3:15PM  Palace Hotel - Concert   Learn more about IPv6 Technologies at Oracle

    Read the article

  • dual boot ubuntu installation mishap

    - by user590849
    I have Windows 7 pc ,where i had 2 partitions, a c drive for my system files and a d drive for my data. I decided to install ubuntu 11.10 a couple of days ago and thought of install it in a separate partition of its own. So i made a separate Linux partition of 30GB. I downloaded ubuntu on my usb stick and installed. During the installation process i was asked where to install ubuntu so i opened up a screen that was similar to this one There were six partitions present ( I had made only 3 partition via windows). Their names were totally different from the ones that i had given in windows. So i selected a drive which had the same size as my Linux partition that i had made in windows ( no other partition had the same size). I clicked on install now and got an error message saying that "There was no root folder set". I set the newly made partition as my root folder and clicked install now. Now out of the 6 partitions that were created 3 were logical ( i had only created 3 partitions in windows). As soon as i clicked install now, the system asked me where i wanted to put my "swap space". I selected one of the logical drives and hit install. Ubuntu successfully installed on my system and at the end it asked me to reboot. I did and got the following error message: "missing operating system". I was shocked. I tried my windows recovery disk ( that i had gotten when i had purchased my laptop) and there i went into startup repair. In the startup repair option i was not able to locate windows. The system asked me to click the "Load drivers" button to load the drivers to my harddrive where windows was installed, but i could not locate any drivers to my harddrive. I tried this several times but to no success. I panicked and installed ubuntu, now this time click "ok" at every step( not worrying about the partition and all). The os installed correctly and i am now able to access my harddrive. NO data within the c drive is lost. All the windows system files are intact. I wish to recover my windows installation. How do i go about it? Thank you in advance. I do not want to format my computer and install windows again.

    Read the article

  • BCP???!????????????:Oracle Data Guard ????

    - by Shinobu FUJINAMI
    ??????????????????????????????????????????????????·????????????????? ??????DG???????????????????????Disk Group???Down Grade????????????????????????????????????????? Oracle ? DG ??Data Guard????????????Oracle Data Guard ???????????????????????????????·??????????????????·???????????????????????????????????????????????????????????????? BCP(??????)????????????????????????????????? Oracle Data Guard ??? Oracle Data Guard ????????KROWN??????·????(KDS) ? Data Guard ??????????????????????????????????????????????????????( KROWN??????·????(KDS) ???????? ) ????·???????????? - ???????? Data Guard Data Guard ?????????BCP ????????????????? Data Guard ???????????????????????????????????? - ???????????????????????????? Data Guard ???????·??????(????????)???????????·??????????·??????2?????????????????·?????????????????? ???????????????????????????????·????????????????????????? - Data Guard >> ??????????? ??????????? Data Guard ???????????ASM ? RAC ??????????????????????????? Data Guard ??? Oracle Database ?????????????????  - DataGuard ??????????????????? (11gR1/11gR2) ???????????????????????????????????????????????????  Data Guard ??? Oracle Database ????????????????? - [DataGuard 11g] ?????·?????????????·???? 11g ????????????·?????????????·????????????????? ??????·??????????????????????????????????? ??·???????????? -  Data Guard >> ??????????? ???????????(?????·?????)?????????(????·?????)?????????/??????·???????????????????????? ??????????????????????? ??????????????????????????????? ???·????????????  - Data Guard >> ???? ????????????????????????????????? Data Guard ???????????????????????????????????? ?????????????????????DataGuard??????????????????????????????? ?????DataGuard???????????????????????????????Data Guard ???????????????????????·????????????????????????????? ???????????????????????????????????????????????????????- Data Guard >> ???? ??????????????? ?????????????????????????????????????????????????????????????? ????????????????????????????????? - Data Guard >> ??????????? ??????????????? ?????README, PSR ???????????????????????????????????????????????????????????????????????????????????????????? Oracle Data Guard ? Oracle9i ???????????????????????????????????Oracle Database 10g ???????????·??????? Data Guard ?????????????????????????????????????????????????????????????????Oracle Database 11g ??????·?????·????????????????????????????????????Oracle Data Guard ????????????????????????????????????????

    Read the article

  • laptop will not boot after attempting upgrade to 13.10

    - by naerwenya
    I wanted to update my OS to the new 14.04 LTS. I was running 12.04 LTS before and followed the advice that upgrades should be done in steps. I first upgraded to 12.10, which seemed to work fine, and later to 13.10. This was all done through the Software Manager. After the last upgrade, I am no longer able to boot up my computer. The GNU GRUB menu opens up, but after selecting Ubuntu, it just stalls with a blank purple screen. If I select one of the other kernels, it also stalls after "Loading initial ramdisk...". I can't get into the Recovery Menu, either. I'm still rather new to Linux and may have possibly made the situation worse. Unfortunately, nothing has worked yet. I tried reinstalling from a flash drive and on my first attempt, the wizard recognised a previous installation. Unfortunately, the wizard also didn't like how my partitions were set up (I didn't change anything) and gave an error before closing. Unfortunately, I didn't write the error down, but it was about the boot partition. On the next attempt and ever since, the installation wizard has stated that "This computer currently has no detected operating systems." This is strange, because I could see the disk and even access my files when booting up from the USB. At this point, I decided to back up my important files using dropbox. Before losing all my files, I wanted to try the Boot-Repair tool, which also produced no results, and the files are no longer visible when booting from USB. The link to the Boot-Repair log is at http://paste.ubuntu.com/7457249/. If I then proceed through to the "Something else" installation option, I can see that the partitions still exist. This is what they look like: /dev/sda free space (size indicated 1MB) /dev/sda1 efi (33MB of 98 MB used) /dev/sda2 efi (352634MB of 746330MB used) /dev/sda3 swap (3725MB, none used) free space (0MB) Is there any way I might be able to get my computer to work and preserve my files as well?

    Read the article

  • Oracle Data Protection: How Do You Measure Up? - Part 1

    - by tichien
    This is the first installment in a blog series, which examines the results of a recent database protection survey conducted by Database Trends and Applications (DBTA) Magazine. All Oracle IT professionals know that a sound, well-tested backup and recovery strategy plays a foundational role in protecting their Oracle database investments, which in many cases, represent the lifeblood of business operations. But just how common are the data protection strategies used and the challenges faced across various enterprises? In January 2014, Database Trends and Applications Magazine (DBTA), in partnership with Oracle, released the results of its “Oracle Database Management and Data Protection Survey”. Two hundred Oracle IT professionals were interviewed on various aspects of their database backup and recovery strategies, in order to identify the top organizational and operational challenges for protecting Oracle assets. Here are some of the key findings from the survey: The majority of respondents manage backups for tens to hundreds of databases, representing total data volume of 5 to 50TB (14% manage 50 to 200 TB and some up to 5 PB or more). About half of the respondents (48%) use HA technologies such as RAC, Data Guard, or storage mirroring, however these technologies are deployed on only 25% of their databases (or less). This indicates that backups are still the predominant method for database protection among enterprises. Weekly full and daily incremental backups to disk were the most popular strategy, used by 27% of respondents, followed by daily full backups, which are used by 17%. Interestingly, over half of the respondents reported that 10% or less of their databases undergo regular backup testing.  A few key backup and recovery challenges resonated across many of the respondents: Poor performance and impact on productivity (see Figure 1) 38% of respondents indicated that backups are too slow, resulting in prolonged backup windows. In a similar vein, 23% complained that backups degrade the performance of production systems. Lack of continuous protection (see Figure 2) 35% revealed that less than 5% of Oracle data is protected in real-time.  Management complexity 25% stated that recovery operations are too complex. (see Figure 1)  31% reported that backups need constant management. (see Figure 1) 45% changed their backup tools as a result of growing data volumes, while 29% changed tools due to the complexity of the tools themselves. Figure 1: Current Challenges with Database Backup and Recovery Figure 2: Percentage of Organization’s Data Backed Up in Real-Time or Near Real-Time In future blogs, we will discuss each of these challenges in more detail and bring insight into how the backup technology industry has attempted to resolve them.

    Read the article

  • Oracle Solaris 11 ?????????:?Oracle Solaris 11 ?????·????·??? ?2????

    - by kazun
    2012?2?20???????????? ??13F????????????Oracle Solaris 11???????????Oracle Solaris 11 ?????·????·????????????????????????2??????????Automated Installer(AI)???Distribution Constructor??????????????????????????????50????????????????????????????????? Oracle Solaris 11 ????????? - ?????????????????? - ???????????????????????? - 2????????????????? ???? Oracle 11 ??????? ?Oracle Solaris 11 ??????????????·??????????(???????? ??????????? ????????????? ??? ??? ??:???)???Oracle Solaris 11????????????????????????? Oracle Solaris 11 ???Oracle Solaris 10 ??????????????????????????2?????????????????(????????GUI???)???????????????????????????????????????????????????????????????????????????????????????????????????????????? ?????????? ???????????????:Automated Installer ????????"hands-free"??????????? Automated Installer?(?? ???????????? ??????????? ?????????????? ??????????????:???)???Oracle Solaris 11 ???????Automated Installer (AI)????????? AI????????????????????Solaris Zones ???????????????????????????????????????????????????????????????????????????????????????Jumpstart ?????????????????? AI?Image Packaging System (IPS)????????????????????????????????????OS???????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????AI??????(XML?????????????)?SC???????????????????????????????????????????????????????????????????????? ??????????????????????????????????AI ???????????DHCP ????????????????????????????? VirtualBox ??????????????? ?:Oracle Solaris Studio ??? AI??????????????????????? ?????????? ???????????????????:Distribution Constructor ?????????????????????????????????????????????? Distribution Constructor?(?? ???????????? ??????????? ????????????? ??????????????:???)???? ?????????Oracle Solaris 11 ????????????????????????????????????? "Distribution Constructor" ?????????????"Distribution Constructor" ???????????????????????????????????????????????????????????????????????????"Distribution Constructor"???LiveCD/USB???????????????ISO?????3???OS?????????????????????Distribution Constructor?????????????????????????????????????????????????????????????????????Distribution Constructor??Solaris ?ZFS???????????AI??????????????????????????XML??????????? ?????????3??????????????????????????????????????????????????????IPS??????????????custom-script????????????????????????????????????????????????????????????????????????? ???????????????????????????????? ?????????? Oracle Solaris ??????? ??????????Installer Disk(3??DVD)????????????????????????Oracle Solaris Live CD(x86)??1???Oracle Solaris 11 Interactive Text Installer??SPARC??x86?????1???????????Live CD??????????Solaris 11 ?????????????????????Interactive Text Installer ??????????????(???????????????????????????????)?Interactive Text Installer ???????????????????????????????????? ???Solaris 11 VM???? for Oracle VM VirtualBox ?????????????????????(?Solaris 11 VM ???? for Oracle VM VirtualBox ???????Oracle VM for x86 ????????)? Oracle VM VirtualBox??????? Solaris 11 VM???? for Oracle VM VirtualBox??????? Oracle Solaris 11?????????????????????????? ?????? Oracle Solaris 10 JumpStart ?? Oracle Solaris 11 ???????????? ???? Oracle Solaris 11 ????????????? Oracle Solaris 11 ???????????

    Read the article

  • AWStats is processing log files but does not display them

    - by Wouter
    I've setup AWStats on my VPS to get some more insight into the traffic coming to my site. As instructed I ran a manual build/update which ran fine: sudo -u www-data ./awstats.pl -config=xxxx.com Create/Update database for config "/etc/awstats/awstats.xxxx.com.conf" by AWStats version 6.9 (build 1.925) From data in log file "/usr/share/doc/awstats/examples/logresolvemerge.pl /var/www/xxxx.com/logs/*-access.log |"... Phase 1 : First bypass old records, searching new record... Searching new records from beginning of log file... Phase 2 : Now process new records (Flush history on disk after 20000 hosts)... Warning: awstats has detected that some hosts names were already resolved in your logfile /usr/share/doc/awstats/examples/logresolvemerge.pl /var/www/xxxx.com/logs/*-access.log |. If DNS lookup was already made by the logger (web server), you should change your setup DNSLookup=1 into DNSLookup=0 to increase awstats speed. Jumped lines in file: 0 Parsed lines in file: 814 Found 0 dropped records, Found 0 corrupted records, Found 0 old records, Found 814 new qualified records. It also produced the file in the DatDir: /var/lib/awstats/awstats052010.xxxx.com.txt which contains what I would expect. BUT when I visit: xxxx.com/awstats/awstats.pl it tells me Last Update: Never updated (See 'Build/Update' on awstats_setup.html page) and the rest of the page is blank. I'm pretty sure I set it up correctly but now I cannot figure out why this is happening. Hopefully someone smarter then me can help me. Thank you in advanced.

    Read the article

  • Windows Backup failed with error 0x807800C5

    - by Alexey Ivanov
    I setup backup of my Windows 8 laptop with Windows 7 File Recovery (known as Backup and Restore in Windows 7). Backup of files runs successfully. But if I try to create system image, it fails with error 0x807800C5: Error details on the dialog: The mounted backup volume is inaccessible. Error details in the system log: There was a failure in preparing the backup image of one of the volumes in the backup set. I save the backup to a network location, WD MyBookLive.   Edit: I tried some of the steps suggested in the various thread about this issue: Cleaned up the backup location: Removed MediaID.bin in the backup location. Removed folder <ComputerName> from WindowsImageBackup. Restarted backup resulted in the same error. However, the error dialog shows slightly different error message: The specified backup disk cannot be found. Performed System File Check by running sfc /scannow. It showed no errors. Running backup failed nevertheless. I tried searching Google for error code but I've found no solution so far. Update: I submitted technical support request to Microsoft. The first suggestion was to clean boot, but it didn't help. I pointed out that I had tried all the methods from the same problem on MS Answers, and nothing had helped.

    Read the article

  • LSI RAID monitor reports "Consistency Check inconsistency logging disabled"

    - by carlpett
    I have a server with a LSI MegaRAID 9261-8i controller. Recently I started getting alerts like this one: Controller ID: 1 Consistency Check inconsistency logging disabled, too many inconsistencies on VD: 0 Generated on:Sat May 12 04:06:40 2012 SYSTEM DETAILS--- IP Address: 192.168.1.29 OS Name: Windows 7 x64 OS Version: 6.01 Driver Name: megasas.sys Driver Version: 4.5.1.64 IMAGE DETAILS--- BIOS Version: 2.120.33-1197 Firmware Package Version: 12.12.0-0045 Firmware Version: 3.21.00_4.11.05.00_0x05000000 VD 0 is a RAID mirror containing the system disk. I have searched and read, but cannot find any trace of how to actually do anything about this. I tried running a scandisk but that did not find anything (as I expected, since scandisk reads the disks as exposed by the controller, right?). The MegaRAID Storage Manager does not as far as I can see have any options for checking or fixing physical disks. The program claims the VD is "healty", and both disks have Error count 0. Also a bit strange is the System details in the message... The IP address is associated with the RAS (dial in) interface, and the OS should be Windows Server 2011 SBS. Has anyone else experienced this before? What can be done?

    Read the article

  • Rebuilding array on 3ware 9690SA-8I

    - by Tim Jones
    I have a RAID10 (8x1TB) array on a 3ware 9690 card running on an Ubuntu 1110 server. There was a kernel update so I scheduled a reboot after which the array was inaccessible. I checked the status a drive has died in the array, but the controller has thrown the entire array into an 'inoperable' state instead of simply degraded (what's the point of the RAID now ;-). After taking out the 'dead' drive I run a quick test to find it completely functional without a bad sector to be found. I try to put the drive back in but the array still marks the disk as degraded (remembering serial number or something??) and the entire array as inoperable... So I swap it out for a known working drive (not the same capacity but higher - should still work) and initiate a rebuild with the the new drive as a replacement. This fails instantly with the error "(0x0B:0x0033): Unit busy : Failed to start Rebuild on Unit 0". The unit shouldn't be busy as it is not mounted (the card itself is listed with lshw but the array it provides is not). I'm pretty much at an impasse now, I don't understand how I can have a single drive failure on a RAID10 that makes the entire array inaccessible, degraded I could understand but inaccessible?? I don't think the controller as prior to the reboot it was completely functional.

    Read the article

  • What does "single-bit ECC errors were detected on the RAID controller" mean?

    - by jsp
    I have a Dell T7600 with a Perc H710P RAID controller and 4 attached 3TB drives. Over the past few months the RAID controller has been intermittently reporting errors on boot: "no boot device found", "adapter at baseport is not responding", disks frequently reported as missing or failed. I have since replaced the RAID controller, the 4 hard drives, and finally the system's motherboard. After replacing the motherboard and rebooting a few times, I got the error Single bit ECC errors were detected on the RAID controller. Please contact technical support to resolve this issue. After rebooting about 20 more times, I haven't seen the ECC error. The system seems otherwise OK, except for the fact that the disk fans will sometimes start blowing at full blast when the the system is sitting completely idle and not stop until I reboot. Are the ECC errors in memory on the RAID controller? Or, does the RAID controller map in system memory, and the ECC errors are really in system memory? Or, are the ECC errors in the 1GB cache that resides in the RAID controller?

    Read the article

  • Outlook 2007 Backup to D:\Outlook Fails - Access Denied, Write-Protected or File In Use

    - by nicorellius
    I can successfully save the Outlook PST file to the default location on the C drive (C:\Documents and Settings\user\ ... \Outlook) but when I change the backup save to directory to Outlook on the D drive I get the error: Cannot copy Outlook: Access is denied. Make sure the disk is not full or write protected and that the file is not currently in use. I suppose it is not that crucial that I save this file here, but I have never seen this problem before and I have made this same change in the past. I did some searching in this knowledge exchange as well as elsewhere on changing permissions, etc, but this didn't help. I discovered that the folder on my D drive (called Outlook) is not write-protected and nor is it read-only, as I can save to and modify files in that directory, as well as rename and delete the directory itself. At the time when I installed this version of Outlook, I used a previously saved Personal Folder (a backup PST file) and I thought having this still open in Outlook was causing the trouble. But I closed it and still have the same problem. I know this is probably a silly error on my part but I would like to figure it out. I'm new to superuser, but the answers I see are usually very good, so I thought I would post my first question. Thanks in advance.

    Read the article

  • What is my miniport's service name?

    - by Ian Boyd
    i am trying to query the physical sector size of my drive using fsutil: C:\Windows\system32>fsutil fsinfo ntfsinfo c: NTFS Volume Serial Number : 0x78cc11b2cc116c1e Version : 3.1 Number Sectors : 0x000000003a382fff Total Clusters : 0x00000000074705ff Free Clusters : 0x00000000022fc29b Total Reserved : 0x00000000000007d0 Bytes Per Sector : 512 Bytes Per Physical Sector : <Not Supported> Bytes Per Cluster : 4096 Bytes Per FileRecord Segment : 1024 Clusters Per FileRecord Segment : 0 Mft Valid Data Length : 0x00000000305c0000 Mft Start Lcn : 0x00000000000c0000 Mft2 Start Lcn : 0x0000000003a382ff Mft Zone Start : 0x0000000006951940 Mft Zone End : 0x0000000006951c80 RM Identifier: 19B22CBE-570D-19DE-9C72-CD758F800DDC You can see that the Bytes Per Physical Sector value is Not Supported: Bytes Per Physical Sector : <Not Supported> In KB Article Microsoft support policy for 4K sector hard drives in Windows, Microsoft says: If fsutil.exe continues to display "Bytes Per Physical Sector : " after you apply the latest storage driver and the required hotfixes, make sure that the following registry path exists: HKLM\CurrentControlSet\Services\<miniport’s service name>\Parameters\Device\ Name: EnableQueryAccessAlignment Type: REG_DWORD Value: 1: Enable The only thing i don't know is what my Miniport's service name is. What is my miniport's service name. i know that my SATA drives are in AHCI mode, and AHCI uses the msahci driver service: Is that my miniport service? "MSAHCI"? See also Hitachi - Advanced Format Technology Brief RMPrepUSB - Advanced Format (4K sector) hard disks Microsoft support policy for 4K sector hard drives in Windows OSR Online - Advance Disk Format support in Storport Virtual Mniport diver Default cluster size for NTFS, FAT, and exFAT Wikipedia - Advanced Format

    Read the article

  • WmiPrvSE memory leak on Windows 2008 *R2*

    - by MichaelGG
    I've seen references on Windows 2008 to WmiPrvSE leaks, but nothing about Windows 2008 R2. We're running R2 on top of Hyper-V (2008). We are also running NSClient++ for monitoring from opsview. Over time, WmiPrvSE.exe starts to use a lot of memory, causing memory alert issues (less than 10% free). VM has 2GB, WmiPrvSE consumes up to 500-600MB before I kill it. Killing the process doesn't seem to have any negative effect; it starts up again and I haven't noticed any problems. But after a day or two, it's back in the same situation. Any ideas on what to do? Resource Monitor doesn't show any Disk or Network IO by WmiPrvSE.exe. Just slowly climbing private memory... Edited to add: We aren't running clustering, or Windows System Resource Manager. The only regular WMI user I can guess is NSClient++, but we don't seem to have this problem on other servers.

    Read the article

  • Commvault Oracle RMAN Restore to new host

    - by Glenn Stauffer
    We use Commvault Simpana 8 and I have a situation where I have backups of an Oracle database on tape that were taken from Host A. Host A suffered a disk failure (lost its raid configuration) and the sys admins are trying to restore it; in the meantime, I'd working to bring the database back up on another host - Host B. I'm running into problems and am trying to sort out the parameters that need to be passed to the Commvault media agent to get this to work. Unfortunately, I do not have access to Commvault support and the backup person is unavailable. Any one have a clue? The backups are there and the media agent reported a successful write when they ran last night. This is what fails: RMAN run { allocate channel t1 device type sbt_tape parms='SBT_LIBRARY=/usr/local/galaxy/Base/libobk.so,BLKSIZE=262144, ENV=(CvClientName=dbsrv2,CvInstanceName=Instance001, CVOraRacDBName=BBDB, CVOraRACDBClientName=BBDB)'; restore spfile to pfile '/tmp/bbdb.ora' from autobackup; }2 3 4 allocated channel: t1 channel t1: sid=34 devtype=SBT_TAPE channel t1: CommVault Systems for Oracle: Version 7.0.0(Build76) Starting restore at 09-MAY-10 channel t1: looking for autobackup on day: 20100509 channel t1: autobackup found: c-3941155360-20100509-01 released channel: t1 RMAN-00571: =========================================================== RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS =============== RMAN-00571: =========================================================== RMAN-03002: failure of restore command at 05/09/2010 18:01:35 ORA-19870: error reading backup piece c-3941155360-20100509-01 ORA-19507: failed to retrieve sequential file, handle="c-3941155360-20100509-01", parms="" ORA-27029: skgfrtrv: sbtrestore returned error ORA-19511: Error received from media manager layer, error text: sbtrestore: Job[0] thread[26316]: InitializeCLRestore() failed.

    Read the article

  • i5 540M or i7 720QM for laptop running VMs and software development tools?

    - by Donald Hughes
    I'm a software developer that would primarily be running Windows 7 as the primary operating system. On a typical day, I might, at any given moment, be running Visual Studio, Expression Web, SQL Server developer (and Management Console), IIS, Photoshop, a dozen browser tabs in 2-3 different browsers, Skype video chat, streaming music, and a couple of VMs (WinXP and Ubuntu) for testing/experimentation. Obviously, RAM is a concern, which is why I plan to use 8 GB so I can devote enough to the VMs to be usable. I'm also tempted to use an ExpressCard SSD for storing the VM disks to ease disk contention. And I know that that is asking a lot from a laptop, and I should just use a desktop, but I need to be able to take my work with me between several locations. It seems that at a reasonable price point, it comes down to the i5 540M versus the i7 720QM. I'm leaning toward the i7 since it would allow me to dedicate a whole hyperthreaded core to each VM, and still have two cores left for the primary OS. I've heard that the i5 has better battery life, but I'm curious for my scenario if there would be a meaningful difference. I don't usually work without a plug, but I do occasionally ride the train or fly and it would be nice to have at least 3 hours of juice for unusual circumstances. And, finally, for this usage scenario, would a dedicated video option be preferred over the i5's integrated video? It sounds like Visual Studio 2010 (and Windows 7) can take advantage of the video card.

    Read the article

  • Difficulty restoring a differential backup in SQL Server, 2 media families are expected or no files

    - by digiguru
    I have sql backups copied from server A to server B on a nightly basis. We want to move the sql server from server A to server B without much downtime, but the files are very large. I assumed that performing a differential backup and restore would solve the problem with the databases. Copy full backup from server A to copy to server B (10+gb) Open SQL Server Managment Studio on server B Right mouse on databases Restore Database Type in the new DB-name Choose "From Device" and browse to the backup file Click Okay. This is now resorting the original "full" backup. Test new db with dev application - everything works :) On original database rightmouse on DB Tasks Backup... Backup Type = Differential, Backup to disk, add a new file, and remove the old one (it needs to be a small file to transfer for the smallest amount of outage) Copy the diff backup onto the new db Right mouse on DB Tasks Restore Database This is where I get stuck. If I add both the new differential file, and the original backup to the restore process I get an error The media loaded on "M:\path\to\backup\full.bak" is formatted to support 1 media families, but 2 media families are expected according to the backup device specification. RESTORE HEADERONLY is terminating abnormally. But if I try to restore using just the differential file I get System.Data.SqlClient.SqlError: The log or differential backup cannot be restored because no files are ready to rollforward. (Microsoft.SqlServer.Smo) Any idea how to do it? Is there a better way of restoring backups with limited downtime?

    Read the article

  • Commvault Oracle RMAN Restore to new host

    - by Glenn Stauffer
    We use Commvault Simpana 8 and I have a situation where I have backups of an Oracle database on tape that were taken from Host A. Host A suffered a disk failure (lost its raid configuration) and the sys admins are trying to restore it; in the meantime, I'd working to bring the database back up on another host - Host B. I'm running into problems and am trying to sort out the parameters that need to be passed to the Commvault media agent to get this to work. Unfortunately, I do not have access to Commvault support and the backup person is unavailable. Any one have a clue? The backups are there and the media agent reported a successful write when they ran last night. This is what fails: run { allocate channel t1 device type sbt_tape parms='SBT_LIBRARY=/usr/local/galaxy/Base/libobk.so,BLKSIZE=262144, ENV=(CvClientName=dbsrv2,CvInstanceName=Instance001, CVOraSID=BBPROD)'; restore spfile to pfile '/tmp/bbdb.ora' from autobackup; } allocated channel: t1 channel t1: sid=34 devtype=SBT_TAPE channel t1: CommVault Systems for Oracle: Version 7.0.0(Build76) Starting restore at 09-MAY-10 channel t1: looking for autobackup on day: 20100509 channel t1: autobackup found: c-3941155360-20100509-01 released channel: t1 RMAN-00571: =========================================================== RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS =============== RMAN-00571: =========================================================== RMAN-03002: failure of restore command at 05/09/2010 18:01:35 ORA-19870: error reading backup piece c-3941155360-20100509-01 ORA-19507: failed to retrieve sequential file, handle="c-3941155360-20100509-01", parms="" ORA-27029: skgfrtrv: sbtrestore returned error ORA-19511: Error received from media manager layer, error text: sbtrestore: Job[0] thread[26316]: InitializeCLRestore() failed.

    Read the article

  • swapping or trashing with vast amounts of unmapped pagecache

    - by Marco
    I'm using kubuntu jaunty (i386 32bit), kernel 2.6.28-13-generic. I've 4Gb of RAM, of which only 3317Mb are seen by the system (I guess because of the 32bit system). I'm seeing that the pagecache utilization is continually growing, up to the point that the system is unusable (after a few days). This happens also when I don't do anything (all user applications closed and the bare minimum of services enabled). If enabled, the system starts to use swap space (using it all in the end). Even if swap is disabled, disk activity becomes continuous, with the system unresponsive. For example, right now the system is working (albeit a tad slow), with only Firefox and wing ide running, and I have 2Gb cached with only 45Mb mapped: $ free total used free shared buffers cached Mem: 3346388 3247328 99060 0 8416 2117980 -/+ buffers/cache: 1120932 2225456 Swap: 2144668 519448 1625220 $ cat /proc/meminfo MemTotal: 3346388 kB MemFree: 97128 kB Buffers: 7872 kB Cached: 2120224 kB SwapCached: 413860 kB Active: 2304596 kB Inactive: 865984 kB Active(anon): 2279168 kB Inactive(anon): 830236 kB Active(file): 25428 kB Inactive(file): 35748 kB Unevictable: 32 kB Mlocked: 32 kB HighTotal: 2492940 kB HighFree: 5456 kB LowTotal: 853448 kB LowFree: 91672 kB SwapTotal: 2144668 kB SwapFree: 1625244 kB Dirty: 84 kB Writeback: 0 kB AnonPages: 629304 kB Mapped: 45768 kB Slab: 45600 kB SReclaimable: 21756 kB SUnreclaim: 23844 kB PageTables: 4468 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 3817860 kB Committed_AS: 3735020 kB VmallocTotal: 122880 kB VmallocUsed: 9352 kB VmallocChunk: 66600 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 888832 kB If I try to drop the caches, little happens: # sync ; echo 3 > /proc/sys/vm/drop_caches ; free total used free shared buffers cached Mem: 3346388 3220580 125808 0 3020 2100600 -/+ buffers/cache: 1116960 2229428 Swap: 2144668 519356 1625312 Right now I've vm.swappiness = 5, but I've tried also with 0 and 1 (without noticeable differences). I've also tried vm.vfs_cache_pressure = 50 and 150 (again, no differences). As I said the pagecache eats all memory even with swapping turned off. What is happening? How to avoid this?

    Read the article

  • swapping or trashing with vast amounts of unmapped pagecache

    - by Marco
    I'm using kubuntu jaunty (i386 32bit), kernel 2.6.28-13-generic. I've 4Gb of RAM, of which only 3317Mb are seen by the system (I guess because of the 32bit system). I'm seeing that the pagecache utilization is continually growing, up to the point that the system is unusable (after a few days). This happens also when I don't do anything (all user applications closed and the bare minimum of services enabled). If enabled, the system starts to use swap space (using it all in the end). Even if swap is disabled, disk activity becomes continuous, with the system unresponsive. For example, right now the system is working (albeit a tad slow), with only firefox and wing ide running, and I have 2Gb cached with only 45Mb mapped: $ free total used free shared buffers cached Mem: 3346388 3247328 99060 0 8416 2117980 -/+ buffers/cache: 1120932 2225456 Swap: 2144668 519448 1625220 $ cat /proc/meminfo MemTotal: 3346388 kB MemFree: 97128 kB Buffers: 7872 kB Cached: 2120224 kB SwapCached: 413860 kB Active: 2304596 kB Inactive: 865984 kB Active(anon): 2279168 kB Inactive(anon): 830236 kB Active(file): 25428 kB Inactive(file): 35748 kB Unevictable: 32 kB Mlocked: 32 kB HighTotal: 2492940 kB HighFree: 5456 kB LowTotal: 853448 kB LowFree: 91672 kB SwapTotal: 2144668 kB SwapFree: 1625244 kB Dirty: 84 kB Writeback: 0 kB AnonPages: 629304 kB Mapped: 45768 kB Slab: 45600 kB SReclaimable: 21756 kB SUnreclaim: 23844 kB PageTables: 4468 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 3817860 kB Committed_AS: 3735020 kB VmallocTotal: 122880 kB VmallocUsed: 9352 kB VmallocChunk: 66600 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 888832 kB If I try to drop the caches, little happes: # sync ; echo 3 > /proc/sys/vm/drop_caches ; free total used free shared buffers cached Mem: 3346388 3220580 125808 0 3020 2100600 -/+ buffers/cache: 1116960 2229428 Swap: 2144668 519356 1625312 Right now I've vm.swappiness = 5, but I've tried also with 0 and 1 (without noticeable differences). I've also tried vm.vfs_cache_pressure = 50 and 150 (again, no differences). As I said the pagecache eats all memory even with swapping turned off. What is happening? How to avoid this? TIA, Marco

    Read the article

  • Dell Perc 6i with FreeBSD 8.1 errors with mfi0: COMMAND xxxxxxxx TIMEOUT AFTER xxx SECONDS

    - by jDempster
    We've recently bought two Dell PowerEdge R710 servers with Perc 6i controllers and 6x 135GB SAS Drives. We'd done some pretty extensive testing on a Dell PowerEdge R510 server with a Perc 6i and 4x 135GB SAS Drives running FreeBSD 8.1 for it's wonderful ZFS support and mfiutil. We hadn't had any problems with the R510 and had got to a point where we where happy with the performance of ZFS. Since running FreeBSD 8.1 on the R710 we've been getting errors from the RAID controller. mfi0: COMMAND 0xffffff80005d1770 TIMEOUT AFTER 6178 SECONDS This usually brings the system to a stand still. But it doesn't always happen, and performs very well up until it does happen. We've been running the disk as 3 mirrored drives striped in ZFS. So far we've noticed that running the drives with RAID10 on the RAID seems to work without errors (still testing). At first I thought hardware error as we'd been running FreeBSD on the R510 with the same controller without any issues. But both R710 have the same issue. All controllers are running the same firmware.

    Read the article

  • Connection speed drops from 1 Gbps to 10 Mbps (Vista 64)

    - by Kevin Hakanson
    I recently got a Windows Home Server (HP MediaSmart Server EX490) setup so I could do backups and other things. However, I am having trouble on my Vista 64 PC. The backup will be making great progress, then it will just slow down. At one point, I noticed the lights on my Netgear GS105 indicated it was not using a 1000 Mbps connection, but a 10 Mbps one. I checked the Status of Local Area Connection (Intel(R) 82567V-2 Gigabit Network Connection) and that also showed the same slow speed. This has happened several times in the last couple days. When I disabled the network device, and then enabled it, it established the 1 Gpbs connection again. However, some of the times the Sent Bytes Activity on the Status windows indicate that the data flow is still slow (100 to 1000 bytes every couple seconds). Obviously, at this rate I could backup faster to floppy disk. :) My question is how to diagnose and fix this problem. When I look at the Administrative Events, I do a Errors: Bonjour Service 456: ERROR: read_msg errno 10054 (An existing connection was forcibly closed by the remote host.) And a Warning: e1yexpress Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected. I am suspicious there is some power saving mode. I found a post suggesting System Idle Power Saver(SIPS) may be the issue. I am going to try that, but looking for other suggestions or diagnostic advice. I have several new items in this configuration: server, client software, switch and cat6 cables.

    Read the article

  • Squid external_acl_type Cannot run process

    - by Alex Rezistorman
    I want to restrict uploading for group of the users via squid. So I've choosen to use external_acl_type but after reload of the squid it returns error. WARNING: Cannot run '/usr/local/etc/squid/lists/newupload.sh' process. Permissions of newupload.sh and squid are the same. newupload.sh is executive. How can I solve this problem? Thnx in advance. newupload.sh #!/bin/sh while read line; do set -- $line length=$1 limit=$2 if [ -z "$length" ] || [ "$length" -le "$2" ]; then echo OK else echo ERR fi done Strings from squid.conf external_acl_type request_body protocol=2.5 %{Content-Lenght} /usr/local/etc/squid/lists/newupload.sh acl request_max_size external request_body 5000 http_access allow users request_max_size Squid version squid -v Squid Cache: Version 3.2.13 configure options: '--with-default-user=squid' '--bindir=/usr/local/sbin' '--sbindir=/usr/local/sbin' '--datadir=/usr/local/etc/squid' '--libexecdir=/usr/local/libexec/squid' '--localstatedir=/var' '--sysconfdir=/usr/local/etc/squid' '--with-logdir=/var/log/squid' '--with-pidfile=/var/run/squid/squid.pid' '--with-swapdir=/var/squid/cache/squid' '--enable-auth' '--enable-build-info' '--enable-loadable-modules' '--enable-removal-policies=lru heap' '--disable-epoll' '--disable-linux-netfilter' '--disable-linux-tproxy' '--disable-translation' '--enable-auth-basic=PAM' '--disable-auth-digest' '--enable-external-acl-helpers= kerberos_ldap_group' '--enable-auth-negotiate=kerberos' '--disable-auth-ntlm' '--without-pthreads' '--enable-storeio=diskd ufs' '--enable-disk-io=AIO Blocking DiskDaemon IpcIo Mmapped' '--enable-log-daemon-helpers=file' '--disable-url-rewrite-helpers' '--disable-ipv6' '--disable-snmp' '--disable-htcp' '--disable-forw-via-db' '--disable-cache-digests' '--disable-wccp' '--disable-wccpv2' '--disable-ident-lookups' '--disable-eui' '--disable-ipfw-transparent' '--disable-pf-transparent' '--disable-ipf-transparent' '--disable-follow-x-forwarded-for' '--disable-ecap' '--disable-icap-client' '--disable-esi' '--enable-kqueue' '--with-large-files' '--enable-cachemgr-hostname=proxy.adir.vbr.ua' '--with-filedescriptors=131072' '--disable-auto-locale' '--prefix=/usr/local' '--mandir=/usr/local/man' '--infodir=/usr/local/info/' '--build=amd64-portbld-freebsd8.3' 'build_alias=amd64-portbld-freebsd8.3' 'CC=cc' 'CFLAGS=-O2 -fno-strict-aliasing -frename-registers -fweb -fforce-addr -fmerge-all-constants -maccumulate-outgoing-args -pipe -march=core2 -I/usr/local/include -DLDAP_DEPRECATED' 'LDFLAGS= -L/usr/local/lib' 'CPPFLAGS=-I/usr/local/include' 'CXX=c++' 'CXXFLAGS=-O2 -fno-strict-aliasing -frename-registers -fweb -fforce-addr -fmerge-all-constants -maccumulate-outgoing-args -pipe -march=core2 -I/usr/local/include -DLDAP_DEPRECATED' 'CPP=cpp' --enable-ltdl-convenience Related post: Restrict uploading for groups in squid http://squid-web-proxy-cache.1019090.n4.nabble.com/flexible-managing-of-request-body-max-size-with-squid-2-5-STABLE12-td1022653.html

    Read the article

< Previous Page | 291 292 293 294 295 296 297 298 299 300 301 302  | Next Page >