Search Results

Search found 9923 results on 397 pages for 'state'.

Page 299/397 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• Blinking power button

  - by Mike Ramsey

  A friend asked me to look at his Gateway DX4640 desktop. When he presses the power button, power goes to the mobo (NVIDIA nForce 630i MCP73PV, GeForce 7100 chipset) and the CPU fan starts spinning. The power button slowely blinks on and off (blue) and the screen briefly says no signal and then goes black. And nothing else; no post code beeps. My initial two conjectures were: 1. Vista was stuck in sleep/hibernation mode, or 2. A power off had left the mobo in a bad state. The fix for both is to: a) Unplug the AC power cord b) hold the power button for 30 second to fully discharge the mobo It didn't help. I left the system unplugged from AC power for an hour. No change. I am out of ideas. Has anybody seen anything like this before? What does a blinking blue power button mean? How can I get more data points to guide trouble shooting? --Thank you, --Mike

  Read the article

• I have added a port to the public zone in firewalld but still can't access the port

  - by mikemaccana

  I've been using iptables for a long time, but have never used firewalld until recently. I have enabled port 3000 TCP via firewalld with the following command: # firewall-cmd --zone=public --add-port=3000/tcp --permanent However I can't access the server on port 3000. From an external box: telnet 178.62.16.244 3000 Trying 178.62.16.244... telnet: connect to address 178.62.16.244: Connection refused There are no routing issues: I have a separate rule for a port forward from port 80 to port 8000 which works fine externally. My app is definitely listening on the port too: Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 0.0.0.0:3000 0.0.0.0:* LISTEN 99 36797 18662/node firewall-cmd doesn't seem to show the port either - see how ports is empty. You can see the forward rule I mentioned earlier. # firewall-cmd --list-all public (default, active) interfaces: eth0 sources: services: dhcpv6-client ssh ports: masquerade: no forward-ports: port=80:proto=tcp:toport=8000:toaddr= icmp-blocks: rich rules: However I can see the rule in the XML config file: # cat /etc/firewalld/zones/public.xml <?xml version="1.0" encoding="utf-8"?> <zone> <short>Public</short> <description>For use in public areas. You do not trust the other computers on networks to not harm your computer. Only selected incoming connections are accepted.</description> <service name="dhcpv6-client"/> <service name="ssh"/> <port protocol="tcp" port="3000"/> <forward-port to-port="8000" protocol="tcp" port="80"/> </zone> What else do I need to do to allow access to my app on port 3000? Also: is adding access via a port the correct thing to do? Or should I make a firewalld 'service' for my app instead?

  Read the article

• Slow boot for OS and external devices

  - by Derek Van Cuyk

  I have been having this problem intermittently but as of yesterday, it has become more consistent. It originally started when I rebooted my PC at home and the OS (Windows 8) sat in a loop appearing to do nothing while loading. I figured since this was a new installation, that something may have just become corrupted and I decided to reinstall. So I tried to boot off of the thumb drive which had the installation iso and encountered pretty much the same issue. Same with the DVD drive. So, I rebooted once again and left it to load the entire night just to see if it ever would and sure enough this morning, Windows had finally loaded. Authentication had the same roblem albeit not quite as long (took about 5 minutes to authenticate). However, once I was in, everything appeared to be working fine and as quick as normal with the exception of when I tried to scan the C drive for any errors, which ran unbearably slow (45 minutes and before I left for work and was not finished scanning a 64GB SSD drive). I mention that I have had this issue but never when loading the OS. Before it occurred when trying to install windows 7 from a different DVD drive than the one I have now. It took me about 3 hours to do it since I had to wait sometimes 30+ min for each step to finish processing. Does anyone have an idea as to what can cause this? I am assuming it is the motherboard since it is responsible for communication with all the devices I'm having issues with but I cannot find anyone else who has had a problem like this and don't want to drop more money on a MB if it isn't the problem. Hardware: Motherboard: Asus M4A78T-E Socket AM3/ AMD 790GX/ Hybrid CrossFireX Hard Drive: Kingston SSDNow V+180 64GB Micro SATA II 3GB/S 1.8 Inch Solid State Drive SVP180S2/64G Optical Drive: Samsung Blu-Ray Combo Internal 12XReadable and DVD-Writable Drive with Lightscribe SH-B123L/BSBP Thanks, Derek

  Read the article

• Database mirroring login failure attempts on mirror server

  - by Chandan

  I have configured database mirroring between two servers at a distance 40 miles away from each other. Server specifications: SQL Server 2008,Standard Edition 64-bit This is same for principal,mirror and witness. The configuration is high-safety with automatic failover Initially we tested our .net application(web application) on both the principal and mirror and made sure that the login is not orpahned. Things run fine generally.But sometimes on the mirror server,I see login failed attempts: Login failed for user 'd0main\user'. Reason: Failed to open the explicitly specified database. [CLIENT: xx.xx.x.x] Message Error: 18456, Severity: 14, State: 38. This error appears 3-4 times a day but not more than that. My question to the experts is:If the principal is alive so why the application tries to connect to mirror.The default time-out for a .net webpage is 30 seconds,so is it possible that the application tries to connect principal and after 30 seconds even if principal is alive,it assumes that it is dead and thus tries to open a connection to mirror where it fails. Please help me with this problem.

  Read the article

• Need for explanation: NetBIOS over TCP/IP on VMware network adapter disturbs access to network share

  - by gyrolf

  (Moved here from StackOverflow) Some time ago nearly all workstations in our team (Windows XP SP2) exhibited intermittend but frequent delays when accessing shares on the network. Typically the first access to a share which hadn't been accessed for some time resulted in a nearly frozen workstation for up to 30 seconds. Then everything started working fine again. Using TCPView from Sysinternals I saw that during this delays there was a connection to the netbios-ssn port on the file server which was in state SYN_SENT. First try: Disable NetBIOS over TCP/IP for the intranet network adapter. Problem solved, but I didn't like to manipulate our centrally managed network configuration for the intranet. Second try: Disable NetBIOS over TCP/IP only for the VMWare network adapter (VMNet1 used for host only communications). Problem solved again! My questions: Why does NetBIOS over TCP/IP on one network adapter disturb NetBIOS over TCP/IP on another network adapter? Is this problem specific to VMWare network adapters? Has anybody else seen this phenomen? Additional information: VMWare Workstation version 6.0.3 At the time I started seriously analysing the problem it was no more possible to find out what had been changed to our systems at the time the problems started.

  Read the article

• Managing multiple Apache proxies simultaneously (mod_proxy_balancer)

  - by Hank

  The frontend of my web application is formed by currently two Apache reverse proxies, using mod_proxy_balancer to distribute traffic over a number of backend application servers. Both frontend reverse proxies, running on separate hosts, are accessible from the internet. DNS round robin distributes traffic over both. In the future, the number of reverse proxies is likely to grow, since the webapplication is very bandwidth-heavy. My question is: how do I keep the state of both reverse balancers / proxies in sync? For example, for maintenance purposes, I might want to reduce the load on one of the backend appservers. Currently I can do that by accessing the Balancer-Manager web form on each proxy, and change the distribution rules. But I have to do that on each proxy manually and make sure I enter the same stuff. Is it possible to "link" multiple instances of mod_proxy_balancer? Or is there a tool out there that connects to a number of instances, and updates all with the same information? Update: The tool should retrieve the runtime status and make runtime changes, just like the existing Balancer-Manager, only for a number of proxies - not just for one. Modification of configuration files is not what I'm interested in (as there are plenty tools for that).

  Read the article

• Either, nginx+php-fpm bad config or nginx+php-fpm cannot handle high query?

  - by The Wolf

  I have wordpress installed in my server configured(hopefully with nginx+php-fpm+mariaDB). I am trying to import using wordpress importer a 1.5MB xml file. Everytime I try to upload it using the importer, it got cut of... meaning just blank screen result.. Here is my error log: actually I just posted 2 of the errors [error] 858#0: *1 connect() failed (111: Connection refused) while connecting to upstream, client: xx.xxx.xx.xx, server: xxx.com, request: "GET xxxx.html HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" [error] 858#0: *13 connect() failed (111: Connection refused) while connecting to upstream, client: xxx.x.xx.xx, server: xxx.com, request: "GET xxxx.php HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" I don't know what is the reason why it can't process the wordpress export .xml. I already increased max_file_upload & etc., but nothing happens. Hope somebody can help me. Here are my conf: nginx.conf user nginx; worker_processes 8; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; server_tokens off; keepalive_timeout 65; fastcgi_read_timeout 500; #gzip on; client_max_body_size 2M; php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. include=/etc/php-fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Default Value: none pid = /var/run/php-fpm/php-fpm.pid ; Error log file ; Default Value: /var/log/php-fpm.log error_log = /var/log/php-fpm/error.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf [root@host etc]# vim php-fpm.conf [root@host etc]# vim php-fpm.conf ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf ps aux [root@host etc]# ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.1 2900 1380 ? Ss Jun02 0:00 init root 2 0.0 0.0 0 0 ? S Jun02 0:00 [kthreadd/9308] root 3 0.0 0.0 0 0 ? S Jun02 0:00 [khelper/9308] root 124 0.0 0.0 2464 576 ? S<s Jun02 0:00 /sbin/udevd -d root 460 0.0 0.1 35976 1308 ? Sl Jun02 0:00 /sbin/rsyslogd -i /var/run/syslogd.pid -c 5 root 474 0.0 0.0 8940 1028 ? Ss Jun02 0:00 /usr/sbin/sshd root 481 0.0 0.0 3264 876 ? Ss Jun02 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid root 491 0.0 0.1 6268 1432 ? S Jun02 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/host.busilak.com. mysql 584 0.1 6.8 679072 71456 ? Sl Jun02 0:04 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib/mysql/plugin --use root 586 0.0 0.3 12008 3820 ? Ss Jun02 0:01 sshd: root@pts/0 root 629 0.0 0.0 9140 756 ? Ss Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 630 0.0 0.0 9140 520 ? S Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 645 0.0 0.1 12788 1928 ? Ss Jun02 0:01 sendmail: accepting connections smmsp 653 0.0 0.1 12576 1728 ? Ss Jun02 0:00 sendmail: Queue runner@01:00:00 for /var/spool/clientmqueue root 691 0.0 0.1 7148 1184 ? Ss Jun02 0:00 crond root 698 0.0 0.1 6272 1688 pts/0 Ss Jun02 0:00 -bash root 1006 0.0 0.0 7828 924 ? Ss 00:30 0:00 nginx: master process /usr/sbin/nginx -c /etc/nginx/nginx.conf nginx 1007 0.0 0.1 8156 1724 ? S 00:30 0:00 nginx: worker process nginx 1008 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1009 0.0 0.1 8020 1356 ? S 00:30 0:00 nginx: worker process nginx 1011 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1012 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1013 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1014 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1015 0.0 0.1 8024 1344 ? S 00:30 0:00 nginx: worker process root 1030 0.0 0.2 25396 2904 ? Ss 00:30 0:00 php-fpm: master process (/etc/php-fpm.conf) apache 1031 0.0 1.9 40700 20624 ? S 00:30 0:00 php-fpm: pool www apache 1032 0.0 2.0 41924 21888 ? S 00:30 0:01 php-fpm: pool www apache 1033 0.0 1.9 41212 20848 ? S 00:30 0:01 php-fpm: pool www apache 1034 0.0 1.9 40956 20792 ? S 00:30 0:01 php-fpm: pool www apache 1035 0.0 2.0 41560 21556 ? S 00:30 0:02 php-fpm: pool www apache 1040 0.0 1.8 39292 19120 ? S 00:30 0:00 php-fpm: pool www root 1125 0.0 0.0 6080 1040 pts/0 R+ 01:04 0:00 ps aux netstat -l [root@host etc]# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 localhost.localdomain:smtp *:* LISTEN tcp 0 0 localhost.locald:cslistener *:* LISTEN tcp 0 0 *:mysql *:* LISTEN tcp 0 0 *:http *:* LISTEN tcp 0 0 *:ssh *:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 60575947 /var/run/saslauthd/mux unix 2 [ ACC ] STREAM LISTENING 60574168 @/com/ubuntu/upstart unix 2 [ ACC ] STREAM LISTENING 60575873 /var/lib/mysql/mysql.sock Hope somebody can help me to figure out what is the problem.

  Read the article

• Is current SATA 6 gb/s equipment simply unreliable?

  - by korkman

  I have a 45-disk array of Seagate Barracuda 3 TB ST3000DM001 (yes these are desktop drives I'm aware of that) in a Supermicro sc847 JBOD, connected via LSI 9285. I have found a solution for the problem description below by reducing speed via MegaCli -PhySetLinkSpeed -phy0 2 -a0; for i in $(seq 48); do MegaCli -PhySetLinkSpeed -phy${i} 2 -a0; done and rebooting. The question remains: Is this typical for current 6 gb/s equipment? Is this the sad state of SATA storage? Or is some of my equipment (the sff-8088 cables come to mind) bad? The Problem was: Synchronizing HW RAID-6, disks kept offlining. Fetching SMART values reveiled that those which offlined did not increase powered-on hours anymore. That is, their firmware (CC4C) seems to crash. Digging into the matter by switching to Software RAID-6, with the disks passed-through, I got tons of kernel messages scattered across all disks, with 6 gb/s: sd 0:0:9:0: [sdb] Sense Key : No Sense [current] Info fld=0x0 sd 0:0:9:0: [sdb] Add. Sense: No additional sense information And finally, when a disk offlines: megasas: [ 5]waiting for 160 commands to complete ... megasas: [35]waiting for 159 commands to complete ... megasas: [155]waiting for 156 commands to complete ... megaraid_sas: pending commands remain after waiting, will reset adapter. Ugly controller reset here, then minutes later: megaraid_sas: Reset successful. sd 0:0:28:0: Device offlined - not ready after error recovery ... sd 0:0:28:0: [sdu] Unhandled error code sd 0:0:28:0: [sdu] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK sd 0:0:28:0: [sdu] CDB: Read(10): 28 00 23 21 2f 40 00 00 70 00 sd 0:0:28:0: [sdu] killing request Reduced speed to 3 gb/s like written above, all problems vanished.

  Read the article

• apt-get : Size mismatch

  - by Cédric Girard

  I created a private deb repository to spread a software and it's updates to 600 Ubuntu netbooks. Each time the network is connected, my script try to do a apt-get update. But sometimes (quite often in fact), I have this : Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch The server is an 2.2 Apache, HTTPS only. There is no error on it's logs. Here is the script : apt-get update apt-get dist-upgrade --force-yes --yes Here is the complete output of apt-get Ign https://myserver maverick Release.gpg Ign https://myserver/ubuntu/ maverick/main Translation-en Ign https://myserver maverick Release Ign https://myserver maverick/main i386 Packages/DiffIndex Ign https://myserver maverick/main i386 Packages Ign https://myserver maverick/main i386 Packages Hit https://myserver maverick/main i386 Packages Reading package lists... Reading package lists... Building dependency tree... Reading state information... The following packages will be upgraded: majdb utilitaires voosicomat 3 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 6207kB/6273kB of archives. After this operation, 0B of additional disk space will be used. WARNING: The following packages cannot be authenticated! utilitaires voosicomat majdb Get:1 https://myserver/ubuntu/ maverick/main voosicomat all 2.0.1 [4755kB] Get:2 https://myserver/ubuntu/ maverick/main majdb all 1.0.17 [1452kB] Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch Fetched 7091kB in 21s (324kB/s) E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Regards Cédric

  Read the article

• Xen Windows Guest spawn doesn't spawn a vnc display

  - by Henrik P. Hessel

  I'm using this HVM File to create a new guest kernel = "/usr/lib/xen-3.2-1/boot/hvmloader" builder='hvm' memory = 4096 # Should be at least 2KB per MB of domain memory, plus a few MB per vcpu. shadow_memory = 64 name = "hessel-windows2008" vif = [ 'ip=188.40.xx.xx,mac=00:16:3E:C1:8F:CE' ] acpi = 1 apic = 1 disk = [ 'file:/home/xen/disks/hessel/win2008/win2008.img,hda,w', 'file:/home/xen/isopool/win2008_32.iso,hdc:cdrom,r' ] device_model = '/usr/lib/xen/bin/qemu-dm' #----------------------------------------------------------------------------- # boot on floppy (a), hard disk (c) or CD-ROM (d) # default: hard disk, cd-rom, floppy boot="dc" sdl=0 vnc=1 vncdisplay=1 vnclisten="0.0.0.0" vncconsole=1 vncpasswd='howtoforge' stdvga=0 serial='pty' usbdevice='tablet' The guest is created without an error. But no vnc display is created. Any ideas, how to fix that? prometheus:~# netstat -ant Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:615 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:6010 0.0.0.0:* LISTEN tcp 0 232 188.40.xx.xx:8080 195.36.75.26:54032 ESTABLISHED tcp 0 0 188.40.xx.xx:8080 195.36.75.26:53085 ESTABLISHED tcp6 0 0 :::8080 :::* LISTEN tcp6 0 0 :::53 :::* LISTEN tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 ::1:6010 :::* LISTEN

  Read the article

• Linksys wireless router will not hardware reset.

  - by Jack M.

  Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

  Read the article

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• External USB HD with -optional- mains?

  - by Stephen

  Hi, I'm Christmas-present-buying, and I'd appreciate recommendations for a USB HD with an optional mains power input. I've hunted, but can't find all the information I want (partially due to sketchy product specifications). Background: This is for a digital TV which I do not own, and so I'd like to get it correct first time. The TV has a USB port to allow recording straight to disk, but the manuals don't say how much power can be drawn through the USB port. The manual's instructions state, possibly generically, to plug the drive in before connecting to the TV. Ideally I'd like a small (2.5"?) drive which can draw power over USB, with an mains power input if it turns out the USB port on the TV doesn't offer enough juice. The ideal is to use one cable, two max. A powered USB hub would introduce too much clutter. I've spotted that the LaCie Petit drives have what appears to be an additional power input, but I'm not even sure from the specs what that is. And the device doesn't ship with a mains adapter. Suggestions?

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• Change OpenVZ route to pass through ip failover

  - by Kevin Campion

  I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

  Read the article

• SQL Full-Text indexing not populating

  - by Sam

  We installed a clustered SQL 2005 installation on windows 2008 and reattached our san drives from another machine and restored to do a migration to new hardware. There have been a few minor issues, but this one has me stuck. Trying to populate Full-Text indexes is not working. I create a basic table with some simple text in a new database and get the same results as old indexes. 2010-09-27 10:30:46.85 spid19s Informational: Full-text Full population initialized for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'). Population sub-tasks: 1. 2010-09-27 10:31:15.36 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001DF. Attempt will be made to reindex it. 2010-09-27 10:31:15.37 spid19s The component 'MSFTE.DLL' reported error while indexing. Component path 'D:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\Binn\MSFTE.DLL'. 2010-09-27 10:31:15.37 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001E0. Attempt will be made to reindex it. The rebuild/repopulate procedure finishes, but I get zero rows in the index. The .dll in the message is present and the service accounts have access to this. My FTData also has data in it, so it seems there wouldn't be permission issue on this folder. Application throws this error: “PHP Warning: mssql_query() [function.mssql-query]: message: Full-text catalog 'ikm_PageIndex_FText' is in an unusable state. Drop and re-create this full-text catalog. (severity 16) in E:\Inetpub\knowledgebase_insidemesa\lib\database\mssql.php on line 154” A microsoft discussion is the only post I found which had claimed to fix this - said it was registry related, but then didn't post the fix.

  Read the article

• ESXi Guests will not boot on IBM x3550 M3

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. VM Host Server: IBM x3550 M3 7944AC1 server w/ 2x Intel Xeon E5607 2.27Ghz CPUs ESXi 5.0.0 Build 623860, built for IBM Hardware downloaded from IBM Storage: 2x500GB SAS local storage 8GB RAM Vt is verified to be ENABLED Server Health Status: Normal The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspucious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space.

  Read the article

• Access keystore on Sun ONE Webserver 6.1 for 2048 bit key length SSL

  - by George Bailey

  We want to get 2048 bit key length CSR requests. The browser based GUI provides us with a 1024 bit CSR and I don't know how to change that. It seems that 1024 bit key lengths will no longer supported by SSL companies. (Lower cost options only support 2048 bit. Thawte who is much more expensive say they accept 1024 for only one or two year certificates, but not 3). The legacy systems in question are running Sun ONE Webserver 6.1. Upgrading would be time consuming and we would rather not have to do that right now. We will be phasing these out but it will take awhile, so... Got it!! http://middlewarekb.wordpress.com/2010/06/30/how-to-generate-2048-bit-keypair-using-sun-one-or-iplanet-6-1-servers/ It is for the same version webserver I am using. /opt/SUNWwbsvr/bin/https/admin/bin/certutil -R -s "CN=sub.domain.ext,OU=org unit,O=company name,L=city,ST=spelled state,C=US,E=email" -a -k rsa -g 2048 -v 12 -d /opt/SUNWwbsvr/alias -P https-sub.domain.ext-hostname- -Z SHA1 Previous efforts edited out.

  Read the article

• open source solution to a gateway for a network of a housing cooperative of 150 people

  - by SirDinosaur

  i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

  Read the article

• Hardware issue: computer plays beep sounds at startup, and then turns off

  - by Darkkurama

  Turns out that after moving, my computer got damaged somehow. I installed my computer 2 days ago. I didn't check the state of the hardware parts and turned the pc on recklessly, not realizing that the cpu fan was dettached from the cpu. After this I reattached the fan. The computer worked kind of faulty after that, because at the time of startup, it would play a long beep (different from the normal beep) and won't display anything. I tried restarting after this incident and it got fixed (don't know how, but it did), and I was even able to play some videogames for some hours (more than 5). This morning I tried to get this issue sorted out by checking again the cpu and in general, the connections, and for my surprise, at the time of turning it on again, the computer wouldn't boot at all. I reapplied some thermal paste to the cpu and fan, but got no results (I did this because the old paste was very badly distributted along the surface of both cpu and fan). Now every time I turn it on, the computer acts randomly: sometimes at startup, it plays a long continous beep and then turns off. one time it played a long continous beep and got to the windows password input screen, but then it turned off More frequently, I turn it on and after some seconds, it turns off without any sound. You can check this video I recorded, which features how the computer behaves most of the time Another one I tried troubleshoting it myself by disconnecting my graphic card, rams, HDD and even the cpu and its fan with no result. Computer specs: Intel Core 2 Quad Q6600 processor, Nvidia xfx gtx 260 black edition, 4 GB ram, 500 GB hard drive, Windows 7 64 bit

  Read the article

• Puppet inventory service using puppetdb

  - by Oli

  I have 3 servers set up. A puppet master using passenger (puppet-server1), dashboard using passenger (puppet-server2) and puppetdb (puppet-server3). I cannot get the inventory service working in the dashboard. The puppet master is able to sign certs and hand out manifests. The nodes have checked in to the dashboard ok The puppetdb appears to be working - logs files as follows: 2012-12-13 17:53:10,899 INFO [command-proc-74] [puppetdb.command] [8490148f-865a-45c8-b5b5-2c8824d753dd] [replace facts] puppet-server3.test.net 2012-12-13 17:53:11,041 INFO [command-proc-74] [puppetdb.command] [dfcc5168-06df-41d4-9a97-77b4cd3f4a2b] [replace catalog] puppet-server3.test.net 2012-12-13 17:55:28,600 INFO [command-proc-74] [puppetdb.command] [b2cc0a96-0404-49f5-96ad-19c778508d3d] [replace facts] puppet-client2.test.net 2012-12-13 17:55:28,729 INFO [command-proc-74] [puppetdb.command] [4dc4b8f3-06df-4dad-a89a-92ac80447b99] [replace catalog] puppet-client2.test.net The puppet master has the following configured in puppet.conf [master] certname = puppet-server1.test.net storeconfigs = true storeconfigs_backend = puppetdb reports = store, http reporturl = http://puppet-server2.test.net/reports/upload The puppet master have the following configured in auth.conf #access for puppet dashboard facts path /facts auth yes method find, search allow dashboard The puppet dashboard has this configured in /usr/share/puppet-dashboard/config/settings.yml # Hostname of the inventory server. inventory_server: 'puppet-server3.test.net' # Port for the inventory server. inventory_port: 8081 The inventory is on as I see a link to the inventory in the dashboard server But I am getting this error: Inventory Could not retrieve facts from inventory service: SSL_connect SYSCALL returned=5 errno=0 state=SSLv3 read finished A clearly an SSL error - but I have followed the documentation and have no idea how to fix this. Can anyone help please? Oli

  Read the article

• Dependencies problems installing openjdk on Ubuntu

  - by Rodnower

  I try to install openjdk-7-jre: sudo apt-get install openjdk-7-jre But I have dependencies problems: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: openjdk-7-jre : Depends: openjdk-7-jre-headless (= 7u7-2.3.2a-0ubuntu0.12.04.1) but it is not going to be installed Depends: libgif4 (>= 4.1.4) but it is not installable Depends: libatk-wrapper-java-jni (>= 0.30.4-0ubuntu2) but it is not installable Recommends: libgnome2-0 but it is not installable Recommends: libgnomevfs2-0 but it is not going to be installed Recommends: ttf-dejavu-extra but it is not installable E: Unable to correct problems, you have held broken packages. This is version of Ubuntu: Ubuntu 12.04.1 LTS I completely don't know how resolve dependencies... Some one can help me? Thank you for ahead.

  Read the article

• Tracking down source of duplicate email messages in Outlook / Exchange environment

  - by Ken Pespisa

  I have a few users, who are also Blackberry users, that occasionally have duplicate emails generated from their "mailbox". I put mailbox in quotes because I'm not exactly sure where the duplicates are created. One of these users is in non-cached mode, and the other is in cached mode, and both experience the problem. In fact, the non-cached mode user was originally experiencing the problem while in cached mode, and I made the switch a few weeks ago to attempt to solve the problem. Today I discovered the issue still exists. I'm not sure if the fact that they are blackberry users could be causing the problem at all. I don't see how, but felt I should mention it anyway. Does anyone have ideas on how I might begin to troubleshoot this? I can see in the non-cached user's mailbox "Sent Items" that the message was sent only once. I confirmed the message does not state that there was a conflict and in fact that makes sense because they are in non-cached mode. On the server, we have a mail journaling feature turned on for our third-party mail archiving system, and I can see that that system sees two sent messages. And likewise, the recipient does in fact have two messages in their inbox with consecutive message IDs ([email protected]) and ([email protected]). It would seem to me that the duplicates are generated on the client, but is there a way to tell for sure?

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• Multiple threads stuck on Tomcat behind Apache mod_proxy

  - by Eddy

  we just took a break at butting our collective heads against this maddening problem we're having. Basically this brand new deployment of Tomcat 6.0.36 crawls down to a halt every couple minutes with many of the worker threads stuck as in the example snippet; only after a while the server gets "unstuck" for another couple minutes. The previous Tomcat works a charm though, but keeping it is not really an option... On netstat, we also see a lot of FIN_WAIT and FIN2_WAIT. "catalina-exec-25" daemon prio=10 tid=0x000000004f9d4000 nid=0x7459 runnable [0x0000000044567000] java.lang.Thread.State: RUNNABLE at java.net.SocketOutputStream.socketWrite0(Native Method) at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92) at java.net.SocketOutputStream.write(SocketOutputStream.java:136) at org.apache.coyote.http11.InternalOutputBuffer.realWriteBytes(InternalOutputBuffer.java:756) at org.apache.tomcat.util.buf.ByteChunk.flushBuffer(ByteChunk.java:448) at org.apache.tomcat.util.buf.ByteChunk.append(ByteChunk.java:363) at org.apache.coyote.http11.InternalOutputBuffer$OutputStreamOutputBuffer.doWrite(InternalOutputBuffer.java:780) at org.apache.coyote.http11.filters.IdentityOutputFilter.doWrite(IdentityOutputFilter.java:118) at org.apache.coyote.http11.InternalOutputBuffer.doWrite(InternalOutputBuffer.java:593) at org.apache.coyote.Response.doWrite(Response.java:560) at org.apache.catalina.connector.OutputBuffer.realWriteBytes(OutputBuffer.java:364) at org.apache.tomcat.util.buf.ByteChunk.flushBuffer(ByteChunk.java:448) at org.apache.catalina.connector.OutputBuffer.doFlush(OutputBuffer.java:318) at org.apache.catalina.connector.OutputBuffer.close(OutputBuffer.java:274) at org.apache.catalina.connector.Response.finishResponse(Response.java:493) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:317) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:861) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:606) at org.apache.tomcat.util.net.JIoEndpoint$SocketProcessor.run(JIoEndpoint.java:396) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:662) Any idea? Eddy

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >