Search Results

Search found 256 results on 11 pages for 'asa ayers'.

Page 3/11 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11  | Next Page >

  • Cisco ASA Site-to-Site VPN Dropping

    - by ScottAdair
    I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

    Read the article

  • Cisco ASA dropping IPsec VPN between istself and CentOS server

    - by sebelk
    Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

    Read the article

  • Problem routing between directly connected Subnets w/ ASA-5510

    - by Zephyr Pellerin
    This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

    Read the article

  • Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

    - by Brandon Bearden
    Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

    Read the article

  • Cisco ASA - Enable communication between same security level

    - by Conor
    I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

    Read the article

  • VPN - Cisco 2800 Series Router and Cisco ASA

    - by NickToyota
    What I currently have: Windows 2003/2008 servers supporting a 150 user environment. Linksys RV082 Router (HQ) and RV042 (satellite) routers Site to Site VPN Tunneling to 5 satellite (< 10 user) offices What I need: End-user VPN allowing myself and users to connect remotely to my network I need to replace our current routers and have been recommended the 2811 Router. Can this router alone be enough to get what I need (VPN tunnelling for users and site to site VPN) or will I require purchasing an additional ASA appliance?

    Read the article

  • Site-to-Site vpn setup amazon ec2 openswan (left) and cisco asa 5540 (right)

    - by user197279
    Need help on this VPN set-up on amazon EC2 using openswan Left side: EC2: setup a peer ip:- according to client using cisco (must be public) encrypted network:- according to client using cisco (must be public) Right side: Cisco ASA 5540: Peer ip: 3.3.3.3 Peer host/rightsubnet: 3.3.3.30/32 (Public NAT'd ip) The goal is to setup a site-to-site vpn connection with the client and I need guidance on the setup required on EC2. Appreciate the help Thanks.

    Read the article

  • PPTP pass through on Cisco ASA 5505 (8.2)

    - by ITGuy24
    Is it possible to setup PPTP VPN traffic (clients outside and server inside) to passthrough a Cisco ASA 5505 if the outside IP address is also being used for PAT? The Cisco examples forward all NAT traffic from the outside to the inside VPN server. I only have one IP available currently and need PAT.

    Read the article

  • Linux tools to choose suitable Cisco ASA 5500

    - by linuxcore
    I have a linux webhosting server which affects a high DDOS. I want to use Cisco ASA 5500 Series Adaptive Security Appliances to protect the linux server from this DDOS. I know there are many factors should you know before you choose the suitable hardware firewall like the amount of this DDOS and pps ..etc Please suggest a linux tools to measure those factors and to help me collect the required informations ( pps - amount of DDOS - concurrent connections and other factors ) Regards,

    Read the article

  • show user list command cisco 5500 ASA

    - by sorrrydoctorforlove
    simple issue.. I'm a noob I am running a cisco 5500 ASA which is used to manage a VPN, I need the command used to check the current user list. I think it might be an 'access-list', if so I have no idea what the name of the access list is, is there a way to show the access lists? thanks.

    Read the article

  • Cisco ASA (Client VPN) to LAN - through second VPN to second LAN

    - by user50855
    We have 2 site that is linked by an IPSEC VPN to remote Cisco ASAs: Site 1 1.5Mb T1 Connection Cisco(1) 2841 Site 2 1.5Mb T1 Connection Cisco 2841 In addition: Site 1 has a 2nd WAN 3Mb bonded T1 Connection Cisco 5510 that connects to same LAN as Cisco(1) 2841. Basically, Remote Access (VPN) users connecting through Cisco ASA 5510 needs access to a service at the end of Site 2. This is due to the way the service is sold - Cisco 2841 routers are not under our management and it is setup to allow connection from local LAN VLAN 1 IP address 10.20.0.0/24. My idea is to have all traffic from Remote Users through Cisco ASA destined for Site 2 to go via the VPN between Site 1 and Site 2. The end result being all traffic that hits Site 2 has come via Site 1. I'm struggling to find a great deal of information on how this is setup. So, firstly, can anyone confirm that what I'm trying to achieve is possible? Secondly, can anyone help me to correct the configuration bellow or point me in the direction of an example of such a configuration? Many Thanks. interface Ethernet0/0 nameif outside security-level 0 ip address 7.7.7.19 255.255.255.240 interface Ethernet0/1 nameif inside security-level 100 ip address 10.20.0.249 255.255.255.0 object-group network group-inside-vpnclient description All inside networks accessible to vpn clients network-object 10.20.0.0 255.255.255.0 network-object 10.20.1.0 255.255.255.0 object-group network group-adp-network description ADP IP Address or network accessible to vpn clients network-object 207.207.207.173 255.255.255.255 access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any source-quench access-list outside_access_in extended permit icmp any any unreachable access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit tcp any host 7.7.7.20 eq smtp access-list outside_access_in extended permit tcp any host 7.7.7.20 eq https access-list outside_access_in extended permit tcp any host 7.7.7.20 eq pop3 access-list outside_access_in extended permit tcp any host 7.7.7.20 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq https access-list outside_access_in extended permit tcp any host 7.7.7.21 eq 5721 access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient any access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient object-group group-adp-network access-list acl-vpnclient extended permit ip object-group group-adp-network object-group group-inside-vpnclient access-list PinesFLVPNTunnel_splitTunnelAcl standard permit 10.20.0.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 10.20.1.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 host 207.207.207.173 access-list inside_nat0_outbound_1 extended permit ip 10.20.1.0 255.255.255.0 host 207.207.207.173 ip local pool VPNPool 10.20.1.100-10.20.1.200 mask 255.255.255.0 route outside 0.0.0.0 0.0.0.0 7.7.7.17 1 route inside 207.207.207.173 255.255.255.255 10.20.0.3 1 crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 288000 crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set reverse-route crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto map outside_dyn_map 20 match address acl-vpnclient crypto map outside_dyn_map 20 set security-association lifetime seconds 28800 crypto map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto isakmp identity address crypto isakmp enable outside crypto isakmp policy 20 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 group-policy YeahRightflVPNTunnel internal group-policy YeahRightflVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 vpn-tunnel-protocol IPSec password-storage disable pfs disable split-tunnel-policy tunnelspecified split-tunnel-network-list value acl-vpnclient default-domain value YeahRight.com group-policy YeahRightFLVPNTunnel internal group-policy YeahRightFLVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 10.20.0.7 vpn-tunnel-protocol IPSec split-tunnel-policy tunnelspecified split-tunnel-network-list value YeahRightFLVPNTunnel_splitTunnelAcl default-domain value yeahright.com tunnel-group YeahRightFLVPN type remote-access tunnel-group YeahRightFLVPN general-attributes address-pool VPNPool tunnel-group YeahRightFLVPNTunnel type remote-access tunnel-group YeahRightFLVPNTunnel general-attributes address-pool VPNPool authentication-server-group WinRadius default-group-policy YeahRightFLVPNTunnel tunnel-group YeahRightFLVPNTunnel ipsec-attributes pre-shared-key *

    Read the article

  • Initial Cisco ASA 5510 Config

    - by Brendan ODonnell
    Fair warning, I'm a but of a noob so please bear with me. I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. I'd appreciate any help I can get. Here's the sh run. : Saved : ASA Version 8.4(3) ! hostname gateway domain-name xxx.local enable password xxx encrypted passwd xxx encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/1 nameif inside security-level 100 ip address 10.x.x.x 255.255.255.0 ! interface Ethernet0/2 shutdown no nameif no security-level no ip address ! interface Ethernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! ftp mode passive dns domain-lookup inside dns server-group DefaultDNS name-server 10.x.x.x domain-name xxx.local same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-network subnet 10.x.x.x 255.255.255.0 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list outside_access_in extended permit ip any any access-list inside_access_in extended permit ip any any pager lines 24 logging enable logging buffered informational logging asdm informational mtu management 1500 mtu inside 1500 mtu outside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside icmp permit any outside no asdm history enable arp timeout 14400 ! object network inside-network nat (any,outside) dynamic interface access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL aaa authentication http console LOCAL http server enable http 192.168.1.0 255.255.255.0 management http 10.x.x.x 255.255.255.0 inside http authentication-certificate management http authentication-certificate inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart telnet timeout 5 ssh 192.168.1.0 255.255.255.0 management ssh 10.x.x.x 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 dhcp-client client-id interface outside dhcpd address 192.168.1.2-192.168.1.254 management dhcpd enable management ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn username xxx password xxx encrypted ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options inspect icmp ! service-policy global_policy global prompt hostname context no call-home reporting anonymous Cryptochecksum:fe19874e18fe7107948eb0ada6240bc2 : end no asdm history enable

    Read the article

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • ASA 5505 stops local internet when connected to VPN

    - by g18c
    Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

    Read the article

  • Cisco ASA bonding/teaming/port-channel capabilities

    - by Antoine Benkemoun
    Hello, This seemed to me like a really simple question that I would be able to answer by myself but I have not been able to find any info on this subject. I have a Cisco ASA 5510 which has 4 FastEthernet interfaces. I was wondering if it would be possible to use 2 or 3 of these interfaces as a port-channel in order to agregate bandwidth for multiple VLANs. I have found no info on the Cisco website nor on Google. Is this just a stupid/crazy idea or am I missing something ? Thank you in advance for your help, Antoine

    Read the article

  • Cisco ASA Hairpinning with Dynamic IP

    - by Joseph Sturtevant
    I currently have my Cisco ASA 5505 firewall configured to forward port 80 from the outside interface to a host on my dmz interface. I also need to allow clients on my inside interface to access the host in the dmz by entering the public ip / dns record in their browsers. I was able to do that by following the instructions here, resulting in the following configuration: static (dmz,outside) tcp interface www 192.168.1.5 www netmask 255.255.255.255 static (dmz,inside) tcp 74.125.45.100 www 192.168.1.5 www netmask 255.255.255.255 (Where 74.125.45.100 is my public IP and 192.168.1.5 is the IP of the dmz host) This works great except for the fact that my network has a dynamic public IP and this configuration will therefore break as soon as my public IP changes. Is there a way to do what I want with a dynamic ip? Note: Adding an internal DNS record won't solve my problem since I have multiple dmz hosts mapped to different ports on the public IP.

    Read the article

  • Cant route VLAN over VPN between Cisco ASA 5505 and Cisco 870

    - by user60984
    We've had an existing VPN between a 5505 and 870 for some time. We've just added VLANs to the network on the 5505 side. We can't seem to figure out how to get devices on the VLANs to communicate with devices on the 870 network which have no VLANs. We're thinking we might have to use a router of sorts to handle the routing before hitting the ASA. We thought PFsense might work well. We've been banging our heads against this thing for 2 days so any immediate help would be great. We're up against a deadline. Thanks!!!

    Read the article

  • Route from Cisco ASA over site to site VPN

    - by Wookie321
    I want to be able to push f/w logging traffic to a server at a remote site. This server is accepting syslog traffic on port 514. In the ASA I've configured it to use this server as a syslog server. The Cisco f/w's inside interface address is 10.0.0.1 and I want to route over the link to an address of 192.168.1.1. The vpn is up and working between sites, and local clients at each site can access resources etc. How would I go about setting up the route from the f/w to this remote server only?

    Read the article

  • Cisco asa 5505 locks up / unresponsive

    - by Chris
    We have a cisco asa 5505 that's new (in service for about 2 months) running 7.2(4) software. Every day around 10a it locks up for approx 10 minutes. We're monitoring it via snmp with stg, and snmp doesn't respond during that time. There's no output in the 'show crash' output. Internet connectivity is also dropped. Wondering if anyone else has seen this and what the fix might be. Currently we're looking at upgrading software, but will need memory upgrade for that. We've forced the speed and duplex on the internal and external interfaces, but the problem is still occurring. It's connected on the internal lan to a netgear 724 gige switch.

    Read the article

  • Force failover a Cisco ASA

    - by user974896
    I have two ASA in a lan state primary\secondary configuration. None of them have "failover active" or "no failover active" in their configuration. Would it be proper to failover in a manner such as: Log into console of primary unit and issue "failover lan state secondary", log into the console of the original secondary unit and issue "failover lan state primary". To fail back simply reverse the process or Log into the console of the primary unit and issue "no failover active", log into the console of the original secondary unit and issue "failover active". To fail back issue "failover active" on the original primary (now secondary) unit, and "no failover active" on the now primary unit. I do not like the second method because it adds configuration directives that were not in place before. Will the first method work?

    Read the article

  • Quickbooks and Cisco ASA 5505

    - by user41516
    I have a Cisco ASA 5505, and everything has seemed to function fine, however I have had problems with Quickbooks 2008 running super slow over the network (Samba) and narrowed it down to the Cisco box. Other Samba transfers seem to be pretty fast, and the Quickbooks file is not very large at all (<25 MB), and other Samba transfers seem to be fine. However, I'm not sure if Quickbooks uses another protocol or if there are other ports that need to be opened. Can anybody give me any clues on how to resolve or troubleshoot the problem or have any prior experience with running Quickbooks over a network?

    Read the article

  • No blocked ports on internal interface of ASA

    - by blsub6
    I have a cisco ASA 5505 with three interfaces: Internal (100), DMZ (50) and External (0). The internal has a IPSEC VPN tunnel to my internal network I couldn't log in to my domain because of all of the port restrictions and such. I tried monitoring the traffic through the interface, seeing what it's blocking and then unblocking those ports but even then it didn't work completely correctly I finally just added a rule to permit any ip traffic from any network to any network on the internal interface and, of course, it worked fine But is that good security practice? Should I be blocking ports on an interface that's internal and over a VPN with the highest security level?

    Read the article

  • Text on Cisco ASA console is garbled/missing letters

    - by Some Linux Nerd
    I've actually looked up a number of solutions for this problem and none of them work. There's this Cisco ASA 5505 that I'd like to use, that outputs mildly garbled text with missing characters. I did some googling and found that the most likely problem is a bad baud rate, so I tried all the baud rates, 7N1, 8N2... basically every possibility minicom had. Then I figured (since I can type ok, just not read) that if I factory reset it that it would fix whatever is set wrong with the terminal. That didn't work either. This usb-db9 adapter and console cable work fine on the catalyst switch in our office. My serial settings are 9600 8N1 with no flow control. Anyone know how to fix this? I have an example of the text on pastebin: http://pastebin.com/MAJF0mVU - it's just lots of "Dfaut cnfiuraionfil cotais 1enty." instead of "Default configuration blah blah"

    Read the article

  • Setup Web Applications on Cisco ASA 9.1

    - by Scott
    I've been looking around the Cisco ASA administration screen with our network admin and haven't found the location where Web Applications can be setup. This seems like it should be a pretty straight forward procedure, especially if I just want to add a global application and not segment out by groups. I've looked through the docs, but they are a mess and answer most questions except for this. If you're going to post a RTFM answer, at least please provide link and location because I have looked. This is the location I'm looking to setup web applications on the clientless web VPN.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11  | Next Page >