Search Results

Search found 5 results on 1 pages for 'user974896'.

Page 1/1 | 1 

• Force failover a Cisco ASA

  - by user974896

  I have two ASA in a lan state primary\secondary configuration. None of them have "failover active" or "no failover active" in their configuration. Would it be proper to failover in a manner such as: Log into console of primary unit and issue "failover lan state secondary", log into the console of the original secondary unit and issue "failover lan state primary". To fail back simply reverse the process or Log into the console of the primary unit and issue "no failover active", log into the console of the original secondary unit and issue "failover active". To fail back issue "failover active" on the original primary (now secondary) unit, and "no failover active" on the now primary unit. I do not like the second method because it adds configuration directives that were not in place before. Will the first method work?

  Read the article

• Cisco redundancy modes

  - by user974896

  I am using a Cisco 6500 series with an SSO redundancy configuration. The show redundancy output is as follows: Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = rpr Maintenance Mode = Disabled Communications = Up I would assume the device is operating in RPR mode although SSO is configured. What could cause this? Shouldn't the operating mode be SSO? EDIT (show redundancy states): my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit = Primary Unit ID = 5 Redundancy Mode (Operational) = rpr Redundancy Mode (Configured) = sso Redundancy State = rpr Split Mode = Disabled Manual Swact = Enabled Communications = Up client count = 60 client_notification_TMR = 30000 milliseconds keep_alive TMR = 9000 milliseconds keep_alive count = 1 keep_alive threshold = 18 RF debug mask = 0x0

  Read the article

• SQUID Transparent SSL proxy (no intercept)

  - by user974896

  I know how to have squid work as a transparent proxy. You put it into transparent mode then use your router or IPTABLES to forward port 80 to the squid port. I would like to do the same for SSL. Every guide I see mentions setting up keys on the squid server. I do not want squid to actually decrypt the SSL traffic then establish a connection with the server, rather I would like squid to simply forward the SSL traffic as is. The only thing I would like to do is be able to check the SSL request for any offending IPs and drop the packets if the destination is one of them.

  Read the article

• Using PVLANs with normal VLANs in a trunked environment

  - by user974896

  Assume a trunked environment with two switches, S1 and S2. The swtiches are connected with a trunk port designed to pass VLAN 26. What would happen if VLAN 26 on S2 is configured as a private-vlan with the default gateway and DHCP server and default gateway as promisc ports. What if S1's VLAN 26 is configured as a standard VLAN. Would the hosts on S1 be able to communicate with the promisc ports on S2? Would they be able to communicate with the hosts on S2? To further complicate things what if the DHCP server were to reside on S1 and I wanted S2 to have private VLANS with promisc ports as the gateway and DHCP server while still leaving S1 in a standard vlan configuration.

  Read the article

• Restoring factory recovery partition (samsung)

  - by user974896

  I have upgraded the HDD in a Samsung laptop and would like to restore the "Press F4 for recovery" partition. My new disk has three partitions, System, Windows, and Recovery. I did a dd of the recovery partition from the old HDD to the new. I also set the diag flag on the new HDD. F4 recovery still is not working. tldr: I mapped my new disk like my old disk with the exception of exact sizes. I did the recover partition from old to new via livecd. F4 recovery does not work

  Read the article

1