Search Results

Search found 101 results on 5 pages for 'd frag'.

Page 3/5 | < Previous Page | 1 2 3 4 5  | Next Page >

• How to get wireless (Alfa) operate in full power and speed up wireless Internet?

  - by MahboobeAlam

  I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• WiFi on Ubuntu 12.04 custom: downloading unbearably slow

  - by Mark

  iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

  Read the article

• Problem with wireless networking

  - by Rodnower

  Hello, I have atheros wifi hardware, intell chipset, gigabyte laptop and CentOS 5 installed. Now I try to use wireless network and get problems. First of all I want to say that I have 2 OS on my laptop, and when I load Windows XP I still may to access to the wireless network. First I try to get it on Linux was to make active wlan0 interface in: system - administration - network but I get: Determining IP information for wlan0... failed. Second I try also was unsuccessfully: [root 1 network-scripts]# ifup-wireless Error : unrecognised wireless request "off" This relevant output of iwconfig is: Warning: Driver for device wlan0 recommend version 21 of Wireless Extension, but has been compiled with version 20, therefore some driver features may not be available... wlan0 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 {output not in the original format} The same things are happen even if I do: modprobe wlan0 (this not get error) Important to say that modprobe not succeed to find ath_pci, tharefor I decide to download latest version of the madwifi driver from http://madwifi-project.org. I extracted this, but when I make this, this is what I get: [root 1 madwifi-0.9.4]# make /bin/sh: line 0: cd: /lib/modules/2.6.18-164.el5/build: No such file or directory Makefile.inc:66: * /lib/modules/2.6.18-164.el5/build is missing, please set KERNELPATH. Stop. I tried to set KERNELPATH, but I think that it was incorrect: [root 1 madwifi-0.9.4]# make KERNELPATH=/lib/modules/2.6.18-164.el5/kernel/ /bin/sh: cc: command not found Makefile.inc:81: * Cannot detect kernel version - please check compiler and KERNELPATH. Stop. Some one have any ideas? Thank you very much for ahead.

  Read the article

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• MS Word custom dictionary making spellcheck slow - ideas?

  - by ezuk

  I have a user who edits technical materials. She uses MS Word's Custom Dictionary all the time for spelling; it has grown very large, and is now making spell check very slow. All of the advice I've read online says to disable the custom dictionary. This is an easy solution, but is not workable for the user, because she actually needs this dictionary. So, is there any way to optimize the custom dictionary and/or Word itself, so that a large dictionary file doesn't slow things down quite so badly? Many thanks. Update after suggestions: I ran contig on the file, and it reports just 1 frag, so that's not the issue I think. The file is 9.95KB -- 1,117 lines, each consisting of just a single word. I viewed the file using Notepad and none of the lines seems corrupted, strange, or overly long (no line seems to be over 10 chars or so). Both of your suggestions were helpful so I will upvote both; any further tips would be most welcome.

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• xml to xsl transformation

  - by amirin

  Hi, I have a requirement to extract the uniquie values from the different nodes of the given xml using xsl transformation. XML FILE:- var IPClaimCausesNice = ""; function changeIPClaimCause(){ if(CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Diagnosis") { IPClaimCausesNice = "diagnosis" } if(CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Illness") { IPClaimCausesNice = "illness" } if(CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Accident") { IPClaimCausesNice = "accident" } return IPClaimCausesNice; } <section id="1903879316" name="Logos"> <fraglink id="605609862" resid="1235000151"> <argvalue name="CommJob"> <var name="CommJob" type="Th_1235001170_CommJob" /> </argvalue> </fraglink> </section> <section id="13483397" name="Address Block"> <fraglink id="563800610" resid="986000123"> <argvalue name="PersonInformation"> <var name="AddresseePersonInformation" type="Th_1235000929_PersonInformation" /> </argvalue> </fraglink> </section> <section id="1093480468" name="Details"> <fraglink id="460316501" resid="1195000163"> <argvalue name="currentDateTime"> <var name="getSystemVariables.getCurrentDate" type="date" /> </argvalue> <argvalue name="CommJob"> <var name="CommJob" type="Th_1235000929_CommJob" /> </argvalue> <argvalue name="ShowDOB" /> <argvalue name="ShowYourRef" /> <argvalue name="YourRefLabel" /> </fraglink> <fraglink id="1026044336" resid="1235000070"> <argvalue name="brandKey"> <var name="CommJob.commJobDetails.brandingKey" type="string" /> </argvalue> <argvalue name="brandSponsor"> <var name="CommJob.client.policy.policyDetails.brandSponsor" type="string" /> </argvalue> </fraglink> </section> <section id="2092948772" name="Important info"> <frag id="1180564368" name="frag" no-match="error" type="text"> <edition id="1178777425" name="Any" withdrawn="False"> <edition-content> <p style="bodyTableHeader" align="left" xml:space="preserve">Important information</p> <p style="body" xml:space="preserve">In accordance with the terms and conditions of your policy, your claim has been classified as a <iif><expression><script language="JavaScript">CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Diagnosis" || CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Ill health"</script><description>the IPClaimCause of the CommJob's client policy insurances Insurance Coverages IPCover Claim equals "Diagnosis" or the IPClaimCause of the CommJob's client policy insurances Insurance Coverages IPCover Claim equals "Ill health"sicknessCommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Accident"the IPClaimCause of the CommJob's client policy insurances Insurance Coverages IPCover Claim equals "Accident"accident. Please assist us Please quote your policy and claim numbers / when returning your forms. Your claim has been received Your Thank you for sending your Initial Claim Form which we received on . We are sorry to hear of your recent . Our assessmentThe attending doctor’s statement indicates you are claiming benefits as a result of , CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Diagnosis"the IPClaimCause of the CommJob's client policy Insurance Coverages first Coverage Claim equals "Diagnosis"which was diagnosedCommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Accident"the IPClaimCause of the CommJob's client policy Insurance Coverages first Coverage Claim equals "Accident"which first occuredCommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause == "Ill health"the IPClaimCause of the CommJob's client policy Insurance Coverages first Coverage Claim equals "Ill health"with symptoms commencing on . We note you ceased all work on and consulted your doctor IsNotMissing(CommJob.placeHolders.date.date5)the date5 of the CommJob's placeHolders date is not missingon this day also regarding your condition. Further information is required We’ve enclosed the following forms. Please complete these and return them to us so that we can continue assessing your claim. Progress claim form Attached questionnaire Authority to the Health Insurance Commission Medical authority <<other/ free format>> <<other/ free format>> Please be advised we’ve CommJob.placeHolders._boolean.boolean1 == truethe CommJob's placeHolders boolean is boolean1also requested the following information: Medical report from Dr Medicare history report from the Health Insurance Commission <<other/ free format>> <<other/ free format>> As your claim forms have been submitted months after you ceased work, our ability to properly assess your claim may have been prejudiced. In order to complete our assessment of your claim, the following information is required within 30 days of this letter: Reason for late lodgement of claim. Reason(s) you ceased work on (eg redundancy or due to medical condition). Name and contact details of all doctors and specialists you have consulted since you ceased work. Copies of any medical, radiology, pathology or other reports in your possession. Details of all treatment you have received since you ceased work. Whether you returned to work (paid or unpaid) in either a full-time or part-time capacity. If so, please provide the dates you worked, hours you worked, duties you performed and any income you received. Financial information for any other related entities (if applicable). If you are unable to supply the above information, please contact us by WriteText(FormatDateTime(DateAdd(getSystemVariables.getCurrentDate,"day",30),"dd MMMM yyyy")). To help in the ongoing assessment of your claim, you are required to be under the regular care and attendance of a medical practitioner. We’ve enclosed a Progress Claim Form which needs to be completed and returned to us by . False False False CC: Different nodes to pick the values:- 1. 2.path form 5. Values to be picked form the xml node and display in HTML is like CommJob.client.policy.Insurance.Coverages.Coverage[0].Claim.IPClaimCause CommJob.commJobDetails.stockType CommJob.commJobDetails.targetClient.targetClientName CommJob.client.policy.policyDetails.policyStatus CommJob.client.policy.policyDetails.productType CommJob.commJobDetails.targetClient.targetClientName ........etc can any one help me to provide the solution. This xsl transformation doesn't pick correctly only the values <xsl:template match="@*"/> Any help on this will great.

  Read the article

• glsl shader to allow color change of skydome ogre3d

  - by Tim

  I'm still very new to all this but learning a lot. I'm putting together an application using Ogre3d as the rendering engine. So far I've got it running, with a simple scene, a day/night cycle system which is working okay. I'm now moving on to looking at changing the color of the skydome material based on the time of day. What I've done so far is to create a struct to hold the ColourValues for the different aspects of the scene. struct todColors { Ogre::ColourValue sky; Ogre::ColourValue ambient; Ogre::ColourValue sun; }; I created an array to store all the colours todColors sceneColours [4]; I populated the array with the colours I want to use for the various times of the day. For instance DayTime (when the sun is high in the sky) sceneColours[2].sky = Ogre::ColourValue(135/255, 206/255, 235/255, 255); sceneColours[2].ambient = Ogre::ColourValue(135/255, 206/255, 235/255, 255); sceneColours[2].sun = Ogre::ColourValue(135/255, 206/255, 235/255, 255); I've got code to work out the time of the day using a float currentHours to store the current hour of the day 10.5 = 10:30 am. This updates constantly and updates the sun as required. I am then calculating the appropriate colours for the time of day when relevant using else if( currentHour >= 4 && currentHour < 7) { // Lerp from night to morning Ogre::ColourValue lerp = Ogre::Math::lerp<Ogre::ColourValue, float>(sceneColours[GT_TOD_NIGHT].sky , sceneColours[GT_TOD_MORNING].sky, (currentHour - 4) / (7 - 4)); } My original attempt to get this to work was to dynamically generate a material with the new colour and apply that material to the skydome. This, as you can probably guess... didn't go well. I know it's possible to use shaders where you can pass information such as colour to the shader from the code but I am unsure if there is an existing simple shader to change a colour like this or if I need to create one. What is involved in creating a shader and material definition that would allow me to change the colour of a material without the overheads of dynamically generating materials all the time? EDIT : I've created a glsl vertex and fragment shaders as follows. Vertex uniform vec4 newColor; void main() { gl_FrontColor = newColor; gl_Position = ftransform(); } Fragment void main() { gl_FragColor = gl_Color; } I can pass a colour to it using ShaderDesigner and it seems to work. I now need to investigate how to use it within Ogre as a material. EDIT : I created a material file like this : vertex_program colour_vs_test glsl { source test.vert default_params { param_named newColor float4 0.0 0.0 0.0 1 } } fragment_program colour_fs_glsl glsl { source test.frag } material Test/SkyColor { technique { pass { lighting off fragment_program_ref colour_fs_glsl { } vertex_program_ref colour_vs_test { } } } } In the code I have tried : Ogre::MaterialPtr material = Ogre::MaterialManager::getSingleton().getByName("Test/SkyColor"); Ogre::GpuProgramParametersSharedPtr params = material->getTechnique(0)->getPass(0)->getVertexProgramParameters(); params->setNamedConstant("newcolor", Ogre::Vector4(0.7, 0.5, 0.3, 1)); I've set that as the Skydome material which seems to work initially. I am doing the same with the code that is attempting to lerp between colours, but when I include it there, it all goes black. Seems like there is now a problem with my colour lerping.

  Read the article

• Slow wifi on Ubuntu 12.04 wifi driver ath9k

  - by lunar

  For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• Unable to make properly work the Ralink rt3090 wifi card on my Lenovo B575 with Kubuntu 12.04 64bit

  - by Sebastien

  I look and tried many solution from many thread but I still unable to make this wifi card work properly (very slow, unable to connect to some wifi spot, etc.). I tried to compile the driver from the ralink website but it doesn't work. Tried to blacklist many mod, withou any result. So here are some command results, hope their help you help me: lspci sebastien@sebastien-portable:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) 00:15.2 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB900 PCI to PCI bridge (PCIE port 2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe lsmod sebastien@sebastien-portable:~$ lsmod Module Size Used by rt2800pci 18715 0 arc4 12529 2 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 55301 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci rt2860sta 864748 0 snd_hda_codec_conexant 62128 1 snd_hda_codec_hdmi 32474 1 uvcvideo 72627 0 rts5139 351143 0 snd_hda_intel 33773 4 videodev 98259 1 uvcvideo snd_hda_codec 127706 3 snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec psmouse 87692 0 v4l2_compat_ioctl32 17128 1 videodev serio_raw 13211 0 k10temp 13166 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec sp5100_tco 13791 0 i2c_piix4 13301 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi ideapad_laptop 18234 0 sparse_keymap 13890 1 ideapad_laptop rfcomm 47604 0 joydev 17693 0 snd_seq_midi_event 14899 1 snd_seq_midi bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 18 snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd mac_hid 13253 0 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 radeon 804372 4 video 19596 0 wmi 19256 0 ttm 76949 1 radeon drm_kms_helper 46978 1 radeon drm 242038 6 radeon,ttm,drm_kms_helper i2c_algo_bit 13423 1 radeon iwconfig sebastien@sebastien-portable:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"4CE6763F0E0A" Mode:Managed Frequency:2.452 GHz Access Point: 4C:E6:76:3F:0E:0A Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:100 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• Randomely loosing wireless connexion with Cubuntu 12.04

  - by statquant

  I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

  Read the article

• How can I change the color of the text in my iFrame? [closed]

  - by VinylScratch

  I have code here: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html> <head> <title>Frag United Banlist</title> </head> <body> <h1>Tekkit Banlist</h1> <?php // change these things $server = "server-host"; $dbuser = "correct-user"; $dbpass = "correct-password"; $dbname = "correct-database"; mysql_connect($server, $dbuser, $dbpass); mysql_select_db($dbname); $result = mysql_query("SELECT * FROM banlist ORDER BY id DESC"); //This will display the most recent by id edit this query how you see fit. Limit, Order, ect. echo "<table width=100% border=1 cellpadding=3 cellspacing=0>"; echo "<tr style=\"font-weight:bold\"> <td>ID</td> <td>User</td> <td>Reason</td> <td>Admin/Mod</td> <td>Time</td> <td>Ban Length</td> </tr>"; while($row = mysql_fetch_assoc($result)){ if($col == "#eeeeee"){ $col = "#ffffff"; }else{ $col = "#eeeeee"; } echo "<tr bgcolor=$col>"; echo "<td>".$row['id']."</td>"; echo "<td>".$row['user']."</td>"; echo "<td>".$row['reason']."</td>"; echo "<td>".$row['admin']."</td>"; //Convert Epoch Time to Standard format $datetime = date("F j, Y, g:i a", $row['time']); echo "<td>$datetime</td>"; $dateconvert = date("F j, Y, g:i a", $row['length']); if($row['length'] == "0"){ echo "<td>None</td>"; }else{ echo "<td>$dateconvert</td>"; } echo "<td>".$row['id']."</td>"; echo "</tr>"; } echo"</table>" ?> </div> </body></html> And I am trying to make it so that when I put it in this iframe: <iframe src="http://bans.fragunited.net/" width="100%" length="100%"><p>Your browser does not support iframes.</p></iframe> But if you go to this page, fragunited.net/bans, (not bans.fragunited.net) the text is black and I want it to be white so you can actually see it. Sorry for the large amount of code, however I don't know where you have to put the code to change the color.

  Read the article

• Why this Either-monad code does not type check?

  - by pf_miles

  instance Monad (Either a) where return = Left fail = Right Left x >>= f = f x Right x >>= _ = Right x this code frag in 'baby.hs' caused the horrible compilation error: Prelude> :l baby [1 of 1] Compiling Main ( baby.hs, interpreted ) baby.hs:2:18: Couldn't match expected type `a1' against inferred type `a' `a1' is a rigid type variable bound by the type signature for `return' at <no location info> `a' is a rigid type variable bound by the instance declaration at baby.hs:1:23 In the expression: Left In the definition of `return': return = Left In the instance declaration for `Monad (Either a)' baby.hs:3:16: Couldn't match expected type `[Char]' against inferred type `a1' `a1' is a rigid type variable bound by the type signature for `fail' at <no location info> Expected type: String Inferred type: a1 In the expression: Right In the definition of `fail': fail = Right baby.hs:4:26: Couldn't match expected type `a1' against inferred type `a' `a1' is a rigid type variable bound by the type signature for `>>=' at <no location info> `a' is a rigid type variable bound by the instance declaration at baby.hs:1:23 In the first argument of `f', namely `x' In the expression: f x In the definition of `>>=': Left x >>= f = f x baby.hs:5:31: Couldn't match expected type `b' against inferred type `a' `b' is a rigid type variable bound by the type signature for `>>=' at <no location info> `a' is a rigid type variable bound by the instance declaration at baby.hs:1:23 In the first argument of `Right', namely `x' In the expression: Right x In the definition of `>>=': Right x >>= _ = Right x Failed, modules loaded: none. why this happen? and how could I make this code compile ? thanks for any help~

  Read the article

• Objective C Enumerate Sentences in a paragraph

  - by Faz Ya

  I would like to write an enumerator that would go through a paragraph of text and gives me one sentence at a time. I tried using stringEnumerate with the NSStringEnumerationBySentences but that simply looks at the periods and fails. For example, lets say I have the following text Block: "Senator John A. Boehner decided not to move forward. He also decided not to call the congress. The news reporter said though...." I would like my function to break down the above paragraph in the following sentences: Senator John A. Boehner decided not to move forward He also decided not to call the congress (No third sentence because it's a half a sentence) The String Enumerator with the sentence optionjust looks at the periods and breaks down that way which is wrong: Senator John A. Boehner decided not to move forward He also decided not to call the congress The news reporter said though.... Is there any library or function that I can call that does a better job at this? Thanks - (NSMutableString *) getOnlyFullSentencesFromTextBlock:(NSMutableString *) textBlock{ [textBlock enumerateSubstringsInRange:NSMakeRange(0, [textBlock length]) options:NSStringEnumerationBySentences | NSStringEnumerationLocalized usingBlock:^(NSString *substring, NSRange substringRange, NSRange enclosingRange, BOOL *stop) { NSLog(@"Sentence Frag:%@", substring); }]; return textBlock; }

  Read the article

• Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

  - by David Brown

  Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

  Read the article

• FreeBSD jail with IPFW with loopback - unable to connect loopback interface

  - by khinester

  I am trying to configure a one IP jail with loopback interface, but I am unsure how to configure the IPFW rules to allow traffic to pass between the jail and the network card on the server. I have followed http://blog.burghardt.pl/2009/01/multiple-freebsd-jails-sharing-one-ip-address/ and https://forums.freebsd.org/viewtopic.php?&t=30063 but without success, here is what i have in my ipfw.rules # vim /usr/local/etc/ipfw.rules ext_if="igb0" jail_if="lo666" IP_PUB="192.168.0.2" IP_JAIL_WWW="10.6.6.6" NET_JAIL="10.6.6.0/24" IPF="ipfw -q add" ipfw -q -f flush #loopback $IPF 10 allow all from any to any via lo0 $IPF 20 deny all from any to 127.0.0.0/8 $IPF 30 deny all from 127.0.0.0/8 to any $IPF 40 deny tcp from any to any frag # statefull $IPF 50 check-state $IPF 60 allow tcp from any to any established $IPF 70 allow all from any to any out keep-state $IPF 80 allow icmp from any to any # open port ftp (20,21), ssh (22), mail (25) # ssh (22), , dns (53) etc $IPF 120 allow tcp from any to any 21 out $IPF 130 allow tcp from any to any 22 in $IPF 140 allow tcp from any to any 22 out $IPF 150 allow tcp from any to any 25 in $IPF 160 allow tcp from any to any 25 out $IPF 170 allow udp from any to any 53 in $IPF 175 allow tcp from any to any 53 in $IPF 180 allow udp from any to any 53 out $IPF 185 allow tcp from any to any 53 out # HTTP $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state # deny and log everything $IPF 500 deny log all from any to any # NAT $IPF 63000 divert natd ip from any to any via $jail_if out $IPF 63000 divert natd ip from any to any via $jail_if in but when i create a jail as: # ezjail-admin create -f continental -c zfs node 10.6.6.7 /usr/jails/node/. /usr/jails/node/./etc /usr/jails/node/./etc/resolv.conf /usr/jails/node/./etc/ezjail.flavour.continental /usr/jails/node/./etc/rc.d /usr/jails/node/./etc/rc.conf 4 blocks find: /usr/jails/node/pkg/: No such file or directory Warning: IP 10.6.6.7 not configured on a local interface. Warning: Some services already seem to be listening on all IP, (including 10.6.6.7) This may cause some confusion, here they are: root syslogd 1203 6 udp6 *:514 *:* root syslogd 1203 7 udp4 *:514 *:* i get these warning and then when i go into the jail environment, i am unable to install any ports. any advice much appreciated.

  Read the article

< Previous Page | 1 2 3 4 5  | Next Page >