Search Results

Search found 577 results on 24 pages for 'dmesg'.

Page 3/24 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• How do I enable SELinux when booting a ramdisk from a CD/DVD?

  - by JeffG

  I have a bootable DVD which boots the same Kernel as the Hard Drive (which uses SELinux). I have copied /etc/selinux and all kernel modules to my ramdisk, and have tried various combinations of selinux=1 and selinux 1 with enforcing 1 and enforcing 0. as Kernel boot parameters. All files contained in the checkpolicy, libselinux, policycoreutils, selinux-policy and selinux-policy-targeted rpms have also been copied into the ramdisk tree. After the system boots from the ramdisk, I check dmesg: % dmesg | grep -i selinux Kernel command line: initrd=idrd.img ramdisk_size=110476 selinux=1 SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability SElinux: Registering netfilter hooks But SELinux isn't running: % /usr/sbin/getenforce Disabled % /usr/sbin/setenforce 1 /usr/sbin/setenforce: SELinux is disabled Neither /var/log/messages nor /proc/kmsg hold clues.

  Read the article

• How do I enable SELinux when booting from a CD/DVD?

  - by JeffG

  I have a bootable DVD which boots the same Kernel as the Hard Drive (which uses SELinux). I have copied /etc/selinux and all the kernel modules to my ramdisk, and have tried both selinux=1 and selinux 1 as Kernel boot parameters. After the system boots, I check dmesg: % dmesg | grep -i selinux Kernel command line: initrd=idrd.img ramdisk_size=110476 selinux=1 SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability SElinux: Registering netfilter hooks But SELinux isn't running: % /usr/sbin/getenforce Disabled % /usr/sbin/setenforce 1 /usr/sbin/setenforce: SELinux is disabled /var/log/messages does not hold any clues. /proc/kmsg also has nothing

  Read the article

• Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

  - by Josh

  As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

  Read the article

• How do I configure an ordinary TV remote control to work with lirc on Linux?

  - by Allan Lewis

  I am running MythTV on Ubuntu 9.10 and I would like to use a TV remote to control it. I know that lirc needs a configuration file for the remote, but none of my remotes is in the official database. If I point a remote at the receiver on my TV card (a Pinnacle PCTV "Solo", model 72e) and press a button, dmesg logs the code generated by the remote, so I assume I just have to make a config file with a list of commands assigned to these codes. I've read a few how-tos but I still don't understand exactly how to create the config file. Some of the guides I've read refer to IR receivers on TV cards working at a "higher level of abstraction", which I take to mean that they decode the signal and provide a code, like the ones I can see in dmesg, rather than just giving raw data, but none of them explain where to go from there! Any help would be greatly appreciated!

  Read the article

• SD-CARD reader does not show in ubuntu

  - by shantanu

  I bought Acer asipre 4250. It have built-in SD card reader. But it is not working. Nothing show in /media or fdisk but something in dmesg. dmesg: new high-speed USB device number 3 using ehci_hcd [ 127.396733] scsi5 : usb-storage 2-2:1.0 [ 128.526562] scsi 5:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 128.532512] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 129.008110] ohci_hcd 0000:00:12.0: PCI INT A disabled [ 129.032083] ohci_hcd 0000:00:13.0: PCI INT A disabled [ 129.056411] ohci_hcd 0000:00:16.0: PCI INT A disabled [ 129.338026] sd 5:0:0:0: [sdb] Attached SCSI removable disk [ 129.808328] ohci_hcd 0000:00:14.5: PCI INT C disabled [ 167.728616] usb 2-2: USB disconnect, device number 3 [ 169.872284] ehci_hcd 0000:00:13.2: PCI INT B disabled [ 169.872340] ehci_hcd 0000:00:13.2: PME# enabled fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0006bc6d Device Boot Start End Blocks Id System /dev/sda1 * 2048 48828415 24413184 7 HPFS/NTFS/exFAT /dev/sda2 48828416 50829311 1000448 82 Linux swap / Solaris /dev/sda3 50829312 99657727 24414208 83 Linux /dev/sda4 99659774 625141759 262740993 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 99659776 275439615 87889920 7 HPFS/NTFS/exFAT /dev/sda6 275441664 451221503 87889920 7 HPFS/NTFS/exFAT /dev/sda7 451223552 625141759 86959104 7 HPFS/NTFS/exFAT I found another problem just right now. I format last three drives as EXT4 with disk utility. But they are showing as NTFS/exFAT in fdisk. :-(

  Read the article

• Bad DMA/do_IRQ errors on suspend/resume, with occasional freezing

  - by Steve Kroon

  Every time I suspend or resume my laptop (Dell Latitude E6520, bought this year), I get 2 messages of the form displayed on the console just before shutting down/starting up: [ 407.107610] ehci_hcd 0000:00:1d.0: dma_pool_free buffer-128, f6f18000/36f18000 (bad dma) On occasion, I get a message of the form: [ 3753.979066] do_IRQ: 0.177 No irq handler for vector (irq -1) On occasion, my machine freezes with a flashing Caps Lock button when suspending, after which I need to do a hard shutdown. This never happened before the messages started appearing (a while back), and I think it never happens without a do_IRQ message appearing (although I'm not sure about that). [There's nothing in the owner's manual on a flashing Caps Lock button; apparently it may be a kernel panic if the scroll lock also flashes, but the laptop doesn't have a scroll lock light, and there's no message on the console saying kernel panic.] Are these bad DMA/do IRQ messages serious, and what can I do to investigate/troubleshoot them and the freezing? Edit: I've also now received the following error messages a few times: [246943.023908] JBD: I/O error detected when updating journal superblock for sdb1. [246943.023958] Buffer I/O error on device sdb1, logical block 0 [246943.023996] EXT3-fs (sdb1): I/O error while writing superblock Edit: Output of dmesg at http://pastebin.com/ra7MTQEj ; contents of /var/log/kern.log at http://pastebin.com/i6jf0Md9 Edit: the output of some smartctl (-a, -x, --log=error, --log=xerror) instructions is available at http://paste.ubuntu.com/1088488/ . Edit (31/8/2012): Output of dmesg|grep -i ehci available at http://paste.ubuntu.com/1177246/ .

  Read the article

• cannot mount root filesystem on 10.04

  - by howaryoo

  I tried to apply the recommendation of question: Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) After running that command: sudo mount --bind /dev /mnt/dev I get this error message: mount: mount point /mnt/dev does not exist fdisk -l returns /dev/sda1 /dev/sda2 /dev/sda5 do I need to mount sda2 and sda5? Edited after @psusi's comment: /dev/sda1 is the boot file system It seems that I need to mount sda2 or sda5. Here is what I tried: (I tried this on a virtual machine so the sda(s) are now vda(s) ) ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/vda: 19.3 GB, 19327352832 bytes 16 heads, 63 sectors/track, 37449 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008eece Device Boot Start End Blocks Id System /dev/vda1 * 3 496 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/vda2 498 37448 18622465 5 Extended Partition 2 does not end on cylinder boundary. /dev/vda5 498 37448 18622464 8e Linux LVM ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ sudo mount -t ext4 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ sudo mount -t ext2 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ Any info that can help me rescue that server would be greatly appreciated!

  Read the article

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• ubuntu input/output error

  - by rplevy

  I'm having a problem with Ubuntu that I'm finding hard to troubleshoot for reasons that will become clear: reboot -bash: /sbin/reboot: Input/output error dmesg -bash: /bin/dmesg: Input/output error ps -e ps: error while loading shared libraries: /lib/libproc-3.2.8.so: cannot read file data: Input/output error lsof -bash: /usr/bin/lsof: Input/output error fsck -bash: /sbin/fsck: Input/output error badblocks -bash: /sbin/badblocks: Input/output error So I can't see what is going on, and I can't remotely reboot. What can I do to get to the bottom of this? Interestingly: init 0 Segmentation fault I can cat /var/syslog but not /var/log/messages or several other important files. less and more don't work, neither do tail or head, etc.

  Read the article

• How to perform diagnostics (stress test) on HP Smartarray Controller

  - by pepoluan

  At my office, we have a server that we suspect its RAID controller (HP Smartarray) is failing. A cold boot, however, does not indicate anything. Can anyone recommend me a method to stress-test the controller? Symptoms that makes me suspect a failing controller: Disk access getting slower, queue getting longer Running dmesg on the XenServer console I see many messages similar to this one: end_request: I/O error, dev tda, sector 253655584 (the sector number is never the same) When we move the VM to another physical host, we no longer see the above message Running idle (without any running VM), the dmesg no longer emit the above message A search on Google indicated that the above message is most commonly associated with a failing SmartArray controller. How can I be sure that the SmartArray controller is failing?

  Read the article

• Why would 70-persistent-net.rules have no effect?

  - by Wes Felter

  I've got a saucy server with a lot of NICs and they end up with weird names like "rename19". I know interface names can be changed by modifying the /etc/udev/rules.d/70-persistent-net.rules file. The first clue that something is wrong is that that file did not exist even though it's supposed to be created automatically. So I decided to write my own based on advice from Linux From Scratch: ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.0", NAME="eth0" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.1", NAME="eth1" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.2", NAME="eth2" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:06:00.3", NAME="eth3" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:0c:00.0", NAME="mezz0" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:0c:00.1", NAME="mezz1" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:1b:00.0", NAME="slot1a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:1b:00.1", NAME="slot1b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:20:00.0", NAME="slot2a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:20:00.1", NAME="slot2b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:11:00.0", NAME="slot3a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:11:00.1", NAME="slot3b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:8b:00.0", NAME="slot4a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:8b:00.1", NAME="slot4b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:90:00.0", NAME="slot5a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:90:00.1", NAME="slot5b" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:95:00.0", NAME="slot6a" ACTION=="add", SUBSYSTEM=="net", BUS=="pci", KERNELS=="0000:95:00.1", NAME="slot6b" (I'm matching on PCI IDs instead of MAC addresses because I have multiple identical machines that I want to apply this configuration to.) After rebooting, nothing has changed. It's like these rules aren't even being read. There's not much going on in dmesg either: $ dmesg | grep udev [ 3.196629] systemd-udevd[323]: starting version 204 [ 6.719140] systemd-udevd[550]: starting version 204 [ 38.695050] init: udev-fallback-graphics main process (1658) terminated with status 1

  Read the article

• Compiling custom kernel 3.7.x lowlatency on Ubuntu 12.04

  - by FlabbergastedPickle

  All, I have a peculiar problem with trying to compile a lowlatency flavor of the latest 3.7 kernel. I retrieved the prepatched source from the launchpad using bzr, compiled it using the usual make-kpkg using the current config file plus default options for the rest, installed the kernel and booted into it. Everything works except for the fglrx and wl drivers that I had to install in the original 12.04 lowlatency kernel. So, I tried recompiling these and succeeded with both of them (no errors were reported)--wl driver required a minor adjustment to system.h include while latest fglrx 12.11 beta11 (released yesterday, Dec. 3rd, 2012) compiled without the hitch. Yet, when I try to modprobe either module (both having in common the fact that they were built after the kernel, fglrx as a deb, and wl via the usual make/make install), I get "FATAL: no MODULENAME module found" (MODULENAME being either wl or fglrx). The graphic driver watermark shows 3D crossed out and "for testing purposes" (or "unsupported hardware," can't remember), and no fglrx or wl is loaded. More mysteriously, dmesg shows no attempt on kernel's behalf to load the said drivers, even though they are clearly in the right /lib/modules/KERNEL_VERSION folder. How is this possible? Has something fundamentally changed in 3.7 kernel that would prevent modprobing of these? I know that there is driver signing option that was merged recently but as far as I could tell the kernel config file generated by the build process had that disabled. OTOH, while building wl driver, I did get a warning that the driver was not signed... Then again, even if the kernel disallowed loading of those modules, shouldn't dmesg reflect that? Any thoughts on this one are most appreciated.

  Read the article

• Double entries in the gnome 3 task bar

  - by Mark

  I am running Ubuntu 12.04 with Gnome 3. All was working well except that graphics were slow and even moving a window on the screen seemed slow. I installed the fglrx ati driver. Which seems to have improved matters. But on first login I had all gnome items duplicated. That is my task bar has the ubuntu sign, then says Applications, then places then the ubuntu sign then Aplications and then places. Any application I run produces two icons at the bottom of the screen. This was after a reboot. I rebooted again. Now I have 3!! On the right each set of icons such as printer is also trippled!! See screenshot at http://jetmark.co.uk/Screenshot.png See Dmesg at http://jetmark.co.uk/dmesg.txt Any suggestions welcome. Reboot - now I have 4!! So one set gets added on each reboot. Help!! I am going to be task barred out before long!!

  Read the article

• Cannot boot: FGLRX 8.780 + Kernel 2.6.35-25

  - by pluc

  The situation before this all happened is pretty standard. I have a HP Pavillion dv5 laptop with an ATI Mobility Radeon 4200 series. It always worked fine with Ubuntu for as long as I can remember. However, at one point, something happened and truly made a majestic mess of things. It might've been extra repos I enabled with Ubuntu Tweak - I do not know. But something made it so that my system would not boot any longer. And when I say "won't boot", this is what I mean: - Durning a normal bootup, any entries (except Windows) selected with GRUB (or BURG, not even sure which one I'm using anymore) will spawn the Ubuntu loading screen - then try to start X (or GDM) 5 times. The screen goes to dark, black and back to the Ubuntu loading screen. Then it just stays there until I spawn another TTY. I have no idea what is happening or why. There are no errors in my logs, and I'm truly at a loss here. I've linked three files: Xorg.0.log, the output of dmesg and the GDM log: Xorg.0.log: http://ubuntu.pastebin.com/tpVKc2tc dmesg: ubuntu.pastebin.com/Nd5aYj45 gdm's :0.log: couldn't post due to lack of points :( Let me know if any of you more knowledgeable folks can restore some sanity in my life. Any help is greatly apreciated.

  Read the article

• USB ports not working on Xubuntu 12.04 LTS

  - by Zchpyvr

  Basically, my USB ports on my IBM Thinkpad T43 have stopped working most of the time. Sometimes, they mount and appear in Nautilus, but other times, they aren't recognized. The timeline of events on this laptop for the past few months: Started having problems after using a USB port hub. The port would sometimes work but would be fixed with the occasional reboot. Re-partitioned/Expanded my Xubuntu partition (I have a Windows XP/Xubuntu dual boot). Now the majority of the time, the USB fails to recognize devices. In addition, the few times they are recognized, the device may suddenly disconnect. Things I've noticed: The devices still receive power from my computer (I can charge my ipod..etc..) I can't understand dmesg outputs. I don't know if lsusb is telling me anything useful. My dmesg output is here: http://pastebin.com/KdNxHcFC Things start to get weird at the bottom of the file. And my lsusb is: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• How to change memory for DomU runtime

  - by saffron

  I have a xen server with xen-4.1.3, linux-image-3.2.0-3-amd64, debian squeeze and 16Gb of RAM. The domain-0 has 1Gb of ram, the rest of memory belongs to the hypervisor. I want to start a guest domain with a minimal amount of memory and increase it runtime later. When I start a guest domain with 256Mb of ram and run xm mem-set domu 4Gb, I get ~3Gb only in domu and a guest domain free says: root@test:~# free total used free shared buffers cached Mem: 2830620 72868 2757752 0 2432 43504 -/+ buffers/cache: 26932 2803688 Swap: 1048572 0 1048572 And a guest domain dmesg says: [ 0.000000] Memory: 175912k/2883584k available (3527k kernel code, 448k absent, 2707224k reserved, 3210k data, 612k init) When I start a guest domain with 2Gb of ram I can run xm mem-set domu 7Gb and get ~7Gb of ram in a guest domain: root@test:~# free total used free shared buffers cached Mem: 6828228 74944 6753284 0 1328 12568 -/+ buffers/cache: 61048 6767180 Swap: 1048572 0 1048572 And a guest domain dmesg: [ 0.000000] Memory: 1674960k/16651264k available (3527k kernel code, 448k absent, 14975856k reserved, 3210k data, 612k init) How can I start a guest domain with a minimal amount of ram (256Mb) and increase it under 15Gb?

  Read the article

• AR9485 wireless card loses ability to connect after hibernation

  - by DrewDiezel

  This has happened twice now, the first time it happened I just reinstalled Ubuntu. The only things that I've been messing with in terms of networking, have been restarting the network-manager service after I resume from hibernate (because it never works right after resume, but restarting the service fixes that), and changing my mac address with ifconfig wlan0 down && ifconfig wlan0 hw ether 11:22:33:44:55 && ifconfig wlan0 up. using tail | dmesg returns a bunch of attempts to connect, saying something like authenticating ... okay you're connected! now I'm going to just disconnect because I feel like it. (reason=3). Any ideas? If it helps maybe I'll add a picture of the tail|dmesg output later. My wireless drivers are as follows: Atheros AR9485 Wireless Network Adapter Hamachi Network Interface Microsoft Virtual Wifi Miniport Adapter Realtek PCIe GBE Family Controller VirtualBox Host-Only Ethernet Adapter Here is a pastebin of some terminal outputs that could help. Also, the reddit thread has a few answers, for anyone curious. It's located here. It is entirely possible that it's just my school wifi blocking out my laptop, and my home wifi sucks. Wifi does work at places other than my home and school, however my phone can connect to both places. Here is a pastebin of the results of the wireless-info script.

  Read the article

• Why is my external USB hard drive sometimes completely inaccessible?

  - by Eliah Kagan

  I have an external USB hard drive, consisting of an 1 TB SATA drive in a Rosewill RX35-AT-SU SLV Aluminum 3.5" Silver USB 2.0 External Enclosure, plugged into my SONY VAIO VGN-NS310F laptop. It is plugged directly into the computer (not through a hub). The drive inside the enclosure is a 7200 rpm Western Digital, but I don't remember the exact model. I can remove the drive from the enclosure (again), if people think it's necessary to know that detail. The drive is formatted ext4. I mount it dynamically with udisks on my Lubuntu 11.10 system, usually automatically via PCManFM. (I have had Lubuntu 12.04 on this machine, and experienced all this same behavior with that too.) Every once in a while--once or twice a day--it becomes inaccessible, and difficult to unmount. Attempting to unmount it with sudo umount ... gives an error message saying the drive is in use and suggesting fuser and lsof to find out what is using it. Killing processes found to be using the drive with fuser and lsof is sometimes sufficient to let me unmount it, but usually isn't. Once the drive is unmounted or the machine is rebooted, the drive will not mount. Plugging in the drive and turning it on registers nothing on the computer. dmesg is unchanged. The drive's access light usually blinks vigorously, as though the drive is being accessed constantly. Then eventually, after I keep the drive off for a while (half an hour), I am able to mount it again. While the drive doesn't work on this machine for a while, it will work immediately on another machine running the same version of Ubuntu. Sometimes bringing it back over from the other machine seems to "fix" it. Sometimes it doesn't. The drive doesn't always stop being accessible while mounted, before becoming unmountable. Sometimes it works fine, I turn off the computer, I turn the computer back on, and I cannot mount the drive. Currently this is the only drive with which I have this problem, but I've had problems that I think are the same as this, with different drives, on different Ubuntu machines. This laptop has another external USB drive plugged into it regularly, which doesn't have this problem. Unplugging that drive before plugging in the "problem" drive doesn't fix the problem. I've opened the drive up and made sure the connections were tight in the past, and that didn't seem to help (any more than waiting the same amount of time that it took to open and close the drive, before attempting to remount it). Does anyone have any ideas about what could be causing this, what troubleshooting steps I should perform, and/or how I could fix this problem altogether? Update: I tried replacing the USB data cable (from the enclosure to the laptop), as Merlin suggested. I should've tried that long ago, since it fits the symptoms perfectly (the drive works on another machine, which would make sense because the cable would be bent at a different angle, possibly completing a circuit of frayed wires). Unfortunately, though, this did not help--I have the same problem with the new cable. I'll try to provide additional detailed information about the drive inside the enclosure, next time I'm able to get the drive working. (At the moment I don't have another machine available to attach it.) Major Update (28 June 2012) The drive seems to have deteriorated considerably. I think this is so, because I've attached it to another machine and gotten lots of errors about invalid characters, when copying files from it. I am less interested in recovering data from the drive than I am in figuring out what is wrong with it. I specifically want to figure out if the problem is the drive or the enclosure. Now, when I plug the drive into the original machine where I was having the problems, it still doesn't appear (including with sudo fdisk -l), but it is recognized by the kernel and messages are added to dmesg. Most of the message consist of errors like this, repeated many times: [ 7.707593] sd 5:0:0:0: [sdc] Unhandled sense code [ 7.707599] sd 5:0:0:0: [sdc] Result: hostbyte=invalid driverbyte=DRIVER_SENSE [ 7.707606] sd 5:0:0:0: [sdc] Sense Key : Medium Error [current] [ 7.707614] sd 5:0:0:0: [sdc] Add. Sense: Unrecovered read error [ 7.707621] sd 5:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 7.707636] end_request: critical target error, dev sdc, sector 0 [ 7.707641] Buffer I/O error on device sdc, logical block 0 Here are all the lines from dmesg starting with when the drive is recognized. Please note that: I'm back to running Lubuntu 12.04 on this machine (and perhaps that's a factor in better error messages). Now that the drive has been plugged into another machine and back into this one, and also now that this machine is back to running 12.04, the drive's access light doesn't blink as I had described. Looking at the drive, it would appear as though it is working normally, with low or no access. This behavior (the errors) occurs when rebooting the machine with the drive plugged in, and also when manually plugging in the drive. A few of the messages are about /dev/sdb. That drive is working fine. The bad drive is /dev/sdc. I just didn't want to edit anything out from the middle.

  Read the article

• How do I mount my External HDD with filesystem type errors?

  - by Snuggie

  I am a relatively new Ubuntu user and I am having some difficulty mounting my external 2TB HDD. When I first installed Linux my external HDD was working just fine, however, it has stopped working and I have a lot of important files on there that I need. Before my HDD would automatically mount and no worries. Now, however, it doesn't automatically mount and when I try to manually mount it I keep running into filesystem type errors that I can't seem to get past. Below are images that depict my step by step process of how I am trying to mount my HDD along with the errors I am receiving. If anybody has any idea what I am doing wrong or how to correct the issue I would greatly appreciate it. Step 1) Ensure the computer recognizes my external HDD. pj@PJ:~$ dmesg ... [ 5790.367910] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1022 PQ: 0 ANSI: 6 [ 5790.368278] scsi 7:0:0:1: Enclosure WD SES Device 1022 PQ: 0 ANSI: 6 [ 5790.370122] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 5790.370310] ses 7:0:0:1: Attached Enclosure device [ 5790.370462] ses 7:0:0:1: Attached scsi generic sg3 type 13 [ 5792.971601] sd 7:0:0:0: [sdb] 3906963456 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 5792.972148] sd 7:0:0:0: [sdb] Write Protect is off [ 5792.972162] sd 7:0:0:0: [sdb] Mode Sense: 47 00 10 08 [ 5792.972591] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.972605] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.975235] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.975249] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.987504] sdb: sdb1 [ 5792.988900] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.988911] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.988920] sd 7:0:0:0: [sdb] Attached SCSI disk Step 2) Check if it mounted properly (it does not) pj@PJ:~$ df -ah Filesystem Size Used Avail Use% Mounted on /dev/sda1 682G 3.9G 644G 1% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 2.9G 4.0K 2.9G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.2G 928K 1.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.9G 156K 2.9G 1% /run/shm gvfs-fuse-daemon 0 0 0 - /home/pj/.gvfs Step 3) Try mounting manually using NTFS and VFAT (both as SDB and SDB1) pj@PJ:~$ sudo mount /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t ntfs /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so pj@PJ:~$ sudo mount -t ntfs /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb1 /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Our embedded linux system won't recognize a USB Device if it is plugged in before powerup. Suggestions?

  - by Blaine

  We are developing on a small embedded device. This device us a gumstix overo board running OpenEmbedded linux. We have our development almost completely done, and have run into the strangest of bugs that we can't figure out. We have a USB Device (Spectrophotometer) that has a USB2.0 Connection and an external power supply for the light source. Typical behavior is that you plug in the power supply, then the USB connection to a host. When the usb connection is detected by the device, the device boots up and enables the light source and fan. The device is then able to be used by the host system. The problem is that if the device is plugged into the Gumstix before we turn on the Gumstix, the USB Device apparently is not probed by the system (and hence does not turn on). Under a normal situation, when the connection is initialized by plugging in the usb cable, the spectro turns itself on and becomes available to the system (this can be seen via "lsusb" typically). Neither of these things are happening. There is no device detected via "lsusb" and no dmesg errors of any kind that we can see. It is as if the device is not plugged in. The device does show up and work fine if we unplug the USB cable and plug it back in once the system is booted up. It turns on and shows up on the usb bus, and we can access it with our driver. On any other desktop or laptop, it does not matter if the host system is on or off when we plug in the spectrometer. This behavior is what I would consider to be "normal" - that the usb system is probed and initialized at boot time, and the usb devices come online. In other words, our system is fully functional as long as we plug in the usb device after the system is booted up. Unfortunately this isn't possible in our final product - everything comes on at once. Additional Info: 1) We have tried a flash drive attached to the system when the system is turned off. Booting up the system brings the flash drive online, as expected 2) There are no messages regarding the spectro or usb device (using dmesg). "lsusb" only lists the USB hubs / controllers. It is literally as if the device is not present and not plugged in. 3) We have tried a brand new image from gumstix and an older image from last year. Both images have this problem. This problem exists on all 3 gumstix devices we use. Does anyone have any suggestions? From what I can tell it isn't really possible to do a complete "reboot" of the usb system that is a complete emulation of "unplugging" and "replugging" a usb device. I feel like what is happening is that there is no initial probe on the usb bus that would trigger the usb handshaking, but this is somehow specific to the spectro. This seems to be a kernel issue or at least an issue in how the kernel is initializing the usb subsystem. I'm not really sure though. I have tried the gumstix mailing list, but there doesn't seem to be anyone who has seen this issue before. Any advice or suggestions on where to start looking would be fantastic. Thank you! Blaine output etc. $ uname -a Linux overo 2.6.33 #1 Tue Apr 27 08:35:38 PDT 2010 armv7l GNU/Linux When the system is up and running and spectro is plugged in (working as intended), this is lsusb: Bus 001 Device 116: ID 2457:1022 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2457 idProduct 0x1022 bcdDevice 0.02 iManufacturer 1 USB4000 1.01.11 iProduct 2 Ocean Optics USB4000 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 400mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) dmesg output: usb usb1: usb auto-resume hub 1-0:1.0: hub_resume usb usb2: usb auto-resume ehci-omap ehci-omap.0: resume root hub hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 2-0:1.0: hub_resume hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub usb usb2: usb resume ehci-omap ehci-omap.0: resume root hub hub 2-0:1.0: hub_resume ehci-omap ehci-omap.0: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT hub 2-0:1.0: port 2: status 0501 change 0001 hub 2-0:1.0: state 7 ports 3 chg 0004 evt 0000 hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: new high speed USB device using ehci-omap and address 2 ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: default language 0x0409 usb 2-2: udev 2, busnum 2, minor = 129 usb 2-2: New USB device found, idVendor=2457, idProduct=1022 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Ocean Optics USB4000 usb 2-2: Manufacturer: USB4000 1.01.11 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: uevent usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent drivers/usb/core/inode.c: creating file '002' dmesg has nothing to say, and lusb simply lists nothing else but the two default usb controllers / hubs if we plug the device in before the system is turned on.

  Read the article

• Raid 1 array won't assemble after power outage. How do I fix this ext4 mirror?

  - by Forkrul Assail

  Two ext4 drives on Raid 1 with mdadm won't reassemble after the power went out for an extended period (UPS drained). After turning the machine back on, mdadm said that the array was degraded, after which it took about 2 days for a full resync, which completed without problems. On trying to remount the array I get: mount: you must specify the filesystem type cat /etc/fstab lines relevant to setup: /dev/md127 /media/mediapool ext4 defaults 0 0 dmesg | tail (on trying to mount) says: [ 1050.818782] EXT3-fs (md127): error: can't find ext3 filesystem on dev md127. [ 1050.849214] EXT4-fs (md127): VFS: Can't find ext4 filesystem [ 1050.944781] FAT-fs (md127): invalid media value (0x00) [ 1050.944782] FAT-fs (md127): Can't find a valid FAT filesystem [ 1058.272787] EXT2-fs (md127): error: can't find an ext2 filesystem on dev md127. cat /proc/mdstat says: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md127 : active (auto-read-only) raid1 sdj[2] sdi[0] 2930135360 blocks super 1.2 [2/2] [UU] unused devices: <none> fsck /dev/md127 says: fsck from util-linux 2.20.1 e2fsck 1.42 (29-Nov-2011) fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/md127 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> mdadm -E /dev/sdi gives me: /dev/sdi: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 37ac1824:eb8a21f6:bd5afd6d:96da6394 Name : sojourn:33 Creation Time : Sat Nov 10 10:43:52 2012 Raid Level : raid1 Raid Devices : 2 Avail Dev Size : 5860271016 (2794.40 GiB 3000.46 GB) Array Size : 2930135360 (2794.39 GiB 3000.46 GB) Used Dev Size : 5860270720 (2794.39 GiB 3000.46 GB) Data Offset : 262144 sectors Super Offset : 8 sectors State : clean Device UUID : 3e6e9a4f:6c07ab3d:22d47fce:13cecfd0 Update Time : Tue Nov 13 20:34:18 2012 Checksum : f7d10db9 - correct Events : 27 Device Role : Active device 0 Array State : AA ('A' == active, '.' == missing) boot@boot ~ $ sudo mdadm -E /dev/sdj /dev/sdj: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 37ac1824:eb8a21f6:bd5afd6d:96da6394 Name : sojourn:33 Creation Time : Sat Nov 10 10:43:52 2012 Raid Level : raid1 Raid Devices : 2 Avail Dev Size : 5860271016 (2794.40 GiB 3000.46 GB) Array Size : 2930135360 (2794.39 GiB 3000.46 GB) Used Dev Size : 5860270720 (2794.39 GiB 3000.46 GB) Data Offset : 262144 sectors Super Offset : 8 sectors State : clean Device UUID : 7fb84af4:e9295f7b:ede61f27:bec0cb57 Update Time : Tue Nov 13 20:34:18 2012 Checksum : b9d17fef - correct Events : 27 Device Role : Active device 1 Array State : AA ('A' == active, '.' == missing) machine@user ~ dmesg | tail [ 61.785866] init: alsa-restore main process (2736) terminated with status 99 [ 68.433548] eth0: no IPv6 routers present [ 534.142511] EXT4-fs (sdi): ext4_check_descriptors: Block bitmap for group 0 not in group (block 2838187772)! [ 534.142518] EXT4-fs (sdi): group descriptors corrupted! [ 546.418780] EXT2-fs (sdi): error: couldn't mount because of unsupported optional features (240) [ 549.654127] EXT3-fs (sdi): error: couldn't mount because of unsupported optional features (240) Since this is Raid 1 it was suggested that I try and mount or fsck the drives separately. After a long fsck on one drive, it ended with this as tail: Illegal double indirect block (2298566437) in inode 39717736. CLEARED. Illegal block #4231180 (2611866932) in inode 39717736. CLEARED. Error storing directory block information (inode=39717736, block=0, num=1092368): Memory allocation failed Recreate journal? yes Creating journal (32768 blocks): Done. *** journal has been re-created - filesystem is now ext3 again *** The drive however still doesn't want to mount: dmesg | tail [ 170.674659] md: export_rdev(sdc) [ 170.675152] md: export_rdev(sdc) [ 195.275288] md: export_rdev(sdc) [ 195.275876] md: export_rdev(sdc) [ 1338.540092] CE: hpet increased min_delta_ns to 30169 nsec [26125.734105] EXT4-fs (sdc): ext4_check_descriptors: Checksum for group 0 failed (43502!=37987) [26125.734115] EXT4-fs (sdc): group descriptors corrupted! [26182.325371] EXT3-fs (sdc): error: couldn't mount because of unsupported optional features (240) [27083.316519] EXT4-fs (sdc): ext4_check_descriptors: Checksum for group 0 failed (43502!=37987) [27083.316530] EXT4-fs (sdc): group descriptors corrupted! Please help me fix this. I never in my wildest nightmares thought a complete mirror would die this badly. Am I missing something? Suggestions on fixing this? Could someone explain why it would resync after the powerout, only to seemingly nuke the drive? Thanks for reading. Any help much appreciated. I've tried everything I can think of, including booting and filesystem checking with SystemRescue and Ubuntu liveboot discs.

  Read the article

• Bluetooth light not turned on and bluetooth also not working on vostro 1014

  - by Dinesh Kumar

  after running following command dmesg | grep -i bluetooth [ 17.106250] Bluetooth: Core ver 2.16 [ 17.107845] Bluetooth: HCI device and connection manager initialized [ 17.107847] Bluetooth: HCI socket layer initialized [ 17.107849] Bluetooth: L2CAP socket layer initialized [ 17.107857] Bluetooth: SCO socket layer initialized [ 18.853255] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 18.853260] Bluetooth: BNEP filters: protocol multicast [ 18.859350] Bluetooth: RFCOMM TTY layer initialized [ 18.859355] Bluetooth: RFCOMM socket layer initialized [ 18.859357] Bluetooth: RFCOMM ver 1.11 [14998.338293] init: bluetooth main process ended, respawning

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >