Search Results

Search found 215 results on 9 pages for 'gib'.

Page 3/9 | < Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >

• Upon reboot, Linux software raid fails to include one device of a RAID1 array

  - by user1389890

  One of my four Linux software raid arrays drops one of its two devices when I reboot my system. The other three arrays work fine. I am running RAID1 on kernel version 2.6.32-5-amd64 (Debian Squeeze). Every time I reboot, /dev/md2 comes up with only one device. I can manually add the device by saying $ sudo mdadm /dev/md2 --add /dev/sdc1. This works fine, and mdadm confirms that the device has been re-added as follows: mdadm: re-added /dev/sdc1 After adding the device and allowing the array time to resynch, this is what the output of $ cat /proc/mdstat looks like: Personalities : [raid1] md3 : active raid1 sda4[0] sdb4[1] 244186840 blocks super 1.2 [2/2] [UU] md2 : active raid1 sdc1[0] sdd1[1] 732574464 blocks [2/2] [UU] md1 : active raid1 sda3[0] sdb3[1] 722804416 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdb1[1] 6835520 blocks [2/2] [UU] unused devices: <none> Then after I reboot, this is what the output of $ cat /proc/mdstat looks like: Personalities : [raid1] md3 : active raid1 sda4[0] sdb4[1] 244186840 blocks super 1.2 [2/2] [UU] md2 : active raid1 sdd1[1] 732574464 blocks [2/1] [_U] md1 : active raid1 sda3[0] sdb3[1] 722804416 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdb1[1] 6835520 blocks [2/2] [UU] unused devices: <none> During reboot, here is the output of $ sudo cat /var/log/syslog | grep mdadm : Jun 22 19:00:08 rook mdadm[1709]: RebuildFinished event detected on md device /dev/md2 Jun 22 19:00:08 rook mdadm[1709]: SpareActive event detected on md device /dev/md2, component device /dev/sdc1 Jun 22 19:00:20 rook kernel: [ 7819.446412] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.446415] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.446782] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.446785] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.515844] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.515847] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.606829] mdadm: sending ioctl 1261 to a partition! Jun 22 19:00:20 rook kernel: [ 7819.606832] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:48 rook kernel: [ 8027.855616] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:48 rook kernel: [ 8027.855620] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:48 rook kernel: [ 8027.855950] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:48 rook kernel: [ 8027.855952] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:49 rook kernel: [ 8027.962169] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:49 rook kernel: [ 8027.962171] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:49 rook kernel: [ 8028.054365] mdadm: sending ioctl 1261 to a partition! Jun 22 19:03:49 rook kernel: [ 8028.054368] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.588662] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.588664] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.601990] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.601991] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.602693] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.602695] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.605981] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.605983] mdadm: sending ioctl 1261 to a partition! Jun 22 19:10:23 rook kernel: [ 9.606138] mdadm: sending ioctl 800c0910 to a partition! Jun 22 19:10:23 rook kernel: [ 9.606139] mdadm: sending ioctl 800c0910 to a partition! Jun 22 19:10:48 rook mdadm[1737]: DegradedArray event detected on md device /dev/md2 Here is the result of $ cat /etc/mdadm/mdadm.conf: ARRAY /dev/md0 metadata=0.90 UUID=92121d42:37f46b82:926983e9:7d8aad9b ARRAY /dev/md1 metadata=0.90 UUID=9c1bafc3:1762d51d:c1ae3c29:66348110 ARRAY /dev/md2 metadata=0.90 UUID=98cea6ca:25b5f305:49e8ec88:e84bc7f0 ARRAY /dev/md3 metadata=1.2 name=rook:3 UUID=ca3fce37:95d49a09:badd0ddc:b63a4792 Here is the output of $ sudo mdadm -E /dev/sdc1 after re-adding the device and letting it resync: /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 98cea6ca:25b5f305:49e8ec88:e84bc7f0 (local to host rook) Creation Time : Sun Jul 13 08:05:55 2008 Raid Level : raid1 Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Array Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Update Time : Mon Jun 24 07:42:49 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : 5fd6cc13 - correct Events : 180998 Number Major Minor RaidDevice State this 0 8 33 0 active sync /dev/sdc1 0 0 8 33 0 active sync /dev/sdc1 1 1 8 49 1 active sync /dev/sdd1 Here is the output of $ sudo mdadm -D /dev/md2 after re-adding the device and letting it resync: /dev/md2: Version : 0.90 Creation Time : Sun Jul 13 08:05:55 2008 Raid Level : raid1 Array Size : 732574464 (698.64 GiB 750.16 GB) Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Mon Jun 24 07:42:49 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 98cea6ca:25b5f305:49e8ec88:e84bc7f0 (local to host rook) Events : 0.180998 Number Major Minor RaidDevice State 0 8 33 0 active sync /dev/sdc1 1 8 49 1 active sync /dev/sdd1 I also ran $ sudo smartctl -t long /dev/sdc and no hardware issues were detected. As long as I do not reboot, /dev/md2 seems to work fine. Does anyone have any suggestions?

  Read the article

• RAID P410i and P812 performance issues

  - by Alexey

  I'm having much trouble with I/O performance of HP DL360 server with two RAID controllers - P410i and P812, Windows Server 2008, 36 GiB RAM and 16 x Intel Xeon x5550. The server runs a bunch of tasks producing heavy sequential I/O, and after about 20-30 minutes of intensive work it looks like the tasks are stuck, not using CPU and with enough free memory (so this cannot be a bottleneck). The same tasks were running quite well on the older server (Windows Server 2003, 4 x Intel Xeon, 12 GiB RAM). RAID cache is present, write-cache battery is installed. Cache is configured as 25% readahead/75% writeback. The swap file resides on the logical disk served by P410i and other logical disks are on P812. Can someone tell me what can be the matter of this? Is this a hardware problem or misconfiguration?

  Read the article

• How to copy a dynamic TrueCrypt volume quickly?

  - by Ivan

  I have created a dynamic TrueCrypt volume file, set it size to 40 GiB and put about 20 GiB of files on it. When I open the volume file properties it says "Size: 40.0 GB, Size on disk: 23.0 GB". When I try to move the volume file to another physical partition it takes a lot of time as it tries to copy all the 40 GB instead of just 20 GB that the volume file actually takes. Also, when it is less than 40 GB free on the target drive it says insufficient space even though it is more than enough space considering how much does the image file actually take. How do I overcome this? Creating a new volume file on the target drive works but needless to say I'd like a better solution.

  Read the article

• Storing large amounts of small files into bigger files on Windows

  - by asmo

  Let's say I have 50 GiB of files that weights around 500 KiB each. My guess is that having, for example, 5 large files of 10 GiB each with the same content archived in them would be better for hard drive performance. Am I correct? Will there be a noticeable gain on an NTFS filesystem? ===================================================================== Finally, which tool could I use to group the files together while retaining the ability to modify the content of the archive with zero or minor performance loss? For example, I like TrueCrypt archiving because after mounting an archive file, it creates a drive which I can use seamlessly as if it was a normal drive. The only thing with TrueCrypt is that I don't need encryption/compression, only archiving.

  Read the article

• How to use second volume devide of amazon EC2

  - by Khoyendra Pande

  I have two volumes of amazon EC2 where by default 1 GiB volume using which has fulled. Now I want to use my second volume which is 9 Gim. I used command cat /proc/partitions I got major minor #blocks name 202 1 1048576 xvda1 202 80 9437184 xvdf Then I hit mkfs.ext3 -F /dev/sdf its showing mkfs.ext3: No such file or directory while trying to determine filesystem size then I hit command df and I got Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda1 1032088 1031280 0 100% / tmpfs 313160 8 313152 1% /lib/init/rw udev 297800 24 297776 1% /dev tmpfs 313160 4 313156 1% /dev/shm overflow 1024 32 992 4% /tmp means still I am unable to use my 9 GiB space Volume. I am conform I have two volume where attachment information is i-7e4fb41c:/dev/sda1 (attached) and i-7e4fb41c:/dev/sdf (attached) where only sda1 is using. Any one know how may I use my second volume(sdf). Thx

  Read the article

• Writing to external drive runs out of space prematurely

  - by steve

  I have a USB 2.0, 500 GB HDD. I am writing a bunch of data to it, that I previously recovered from the drive. I have formatted the drive in exFAT, since the drive will be used with Windows and OSX. At first, I tried using Windows explorer to move the files over to the drive (about 160 GiB worth) but after copying about 30% of the data (according to TeraCopy), Windows Explorer reported the drive as out of space, and that it was completely full. WinDirStat only showed the size of data that had been copied over... Where did this extra space go? Why is there a 300+ GiB discrepancy between the usage reported by the files and what Explorer sees?

  Read the article

• Raid 5 with 4 disks on Debian automatically creates a spare drive

  - by Razer

  I'm trying to to create a RAID 5 with 4x 2TB disks on Debian 6. I followed the instructions from: http://zackreed.me/articles/38-software-raid-5-in-debian-with-mdadm I created the raid with following command: sudo mdadm --create --verbose /dev/md0 --auto=yes --level=5 --raid-devices=4 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 After creating the RAID mdadm --detail /dev/md0 shows me: /dev/md0: Version : 1.2 Creation Time : Mon Jun 11 18:14:26 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 11 18:14:26 2012 State : clean, degraded Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : rsserver:0 (local to host rsserver) UUID : a68c3c99:1ef865e9:5a8a7bdc:64710ed8 Events : 0 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 8 33 1 active sync /dev/sdc1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 65 - spare /dev/sde1 Why is there a spare drive? I didn't create one. I don't want to use a spare drive.

  Read the article

• How to partition my hard drive, quicker?

  - by Sam

  When I install Windows 7 on my hard drive, it makes three partitions. One with the OS itself, one with bootmgr inside (that is 100 MiB), and one with the factory image (all the crapware from HP). My final goal is to have the OS on a partition of 100 GiB and keep the rest (900 GiB) for storage. I thought it would be easy using gparted, but it is taking so long. It will take hours. There must a way to partition the drive before installing Windows. Yeah, because what I think makes the shrinking/moving of the partitions take so long is because they are not empty (am I wrong?).

  Read the article

• USB hard drive not recognized

  - by user318772

  Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

  Read the article

• How do I align my partition table properly?

  - by Jorge Castro

  I am in the process of building my first RAID5 array. I've used mdadm to create the following set up: root@bondigas:~# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Wed Oct 20 20:00:41 2010 Raid Level : raid5 Array Size : 5860543488 (5589.05 GiB 6001.20 GB) Used Dev Size : 1953514496 (1863.02 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 20 20:13:48 2010 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 1% complete UUID : f6dc829e:aa29b476:edd1ef19:85032322 (local to host bondigas) Events : 0.12 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 8 32 1 active sync /dev/sdc 2 8 48 2 active sync /dev/sdd 4 8 64 3 spare rebuilding /dev/sde While that's going I decided to format the beast with the following command: root@bondigas:~# mkfs.ext4 /dev/md1p1 mke2fs 1.41.11 (14-Mar-2010) /dev/md1p1 alignment is offset by 63488 bytes. This may result in very poor performance, (re)-partitioning suggested. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=16 blocks, Stripe width=48 blocks 97853440 inodes, 391394047 blocks 19569702 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 11945 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 Writing inode tables: ^C 27/11945 root@bondigas:~# ^C I am unsure what to do about "/dev/md1p1 alignment is offset by 63488 bytes." and how to properly partition the disks to match so I can format it properly.

  Read the article

• raid md device is not remove from memory, how to overcome this problem

  - by santhosha

  i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

  Read the article

• How do I align my partition table properly?

  - by Jorge Castro

  I am in the process of building my first RAID5 array. I've used mdadm to create the following set up: root@bondigas:~# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Wed Oct 20 20:00:41 2010 Raid Level : raid5 Array Size : 5860543488 (5589.05 GiB 6001.20 GB) Used Dev Size : 1953514496 (1863.02 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 20 20:13:48 2010 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 1% complete UUID : f6dc829e:aa29b476:edd1ef19:85032322 (local to host bondigas) Events : 0.12 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 8 32 1 active sync /dev/sdc 2 8 48 2 active sync /dev/sdd 4 8 64 3 spare rebuilding /dev/sde While that's going I decided to format the beast with the following command: root@bondigas:~# mkfs.ext4 /dev/md1p1 mke2fs 1.41.11 (14-Mar-2010) /dev/md1p1 alignment is offset by 63488 bytes. This may result in very poor performance, (re)-partitioning suggested. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=16 blocks, Stripe width=48 blocks 97853440 inodes, 391394047 blocks 19569702 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 11945 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 Writing inode tables: ^C 27/11945 root@bondigas:~# ^C I am unsure what to do about "/dev/md1p1 alignment is offset by 63488 bytes." and how to properly partition the disks to match so I can format it properly.

  Read the article

• Convert mkv to mp4 with ffmpeg

  - by JohnS

  When I try converting mkv to mp4 using ffmpeg, the following error occurs: [ipod @ 0x16fa0a0] Application provided invalid, non monotonically increasing dts to muxer in stream 0: -2 = -2 av_interleaved_write_frame(): Invalid argument I used this command to convert the file: ffmpeg -i input.mkv -vcodec copy -acodec copy -absf aac_adtstoasc output.m4v The input file has the following characteristics: mediainfo input.mkv General Unique ID : 200459305952356554213392832683163418790 (0x96CF0ED8DB5914CBB9E18163689280A6) Complete name : input.mkv Format : Matroska Format version : Version 2 File size : 1.46 GiB Duration : 1h 5mn Overall bit rate : 3 168 Kbps Encoded date : UTC 2010-09-26 21:44:02 Writing application : mkvmerge v2.9.5 ('Tu es le seul') built on Jun 17 2009 16:28:30 Writing library : libebml v0.7.8 + libmatroska v0.8.1 Video ID : 1 Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Format settings, CABAC : Yes Format settings, ReFrames : 4 frames Codec ID : V_MPEG4/ISO/AVC Duration : 1h 5mn Bit rate : 2 910 Kbps Width : 1 280 pixels Height : 720 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Bits/(Pixel*Frame) : 0.126 Stream size : 1.31 GiB (90%) Writing library : x264 core 105 r1724 b02df7b Encoding settings : cabac=1 / ref=3 / deblock=1:0:0 / analyse=0x3:0x113 / me=hex / subme=6 / psy=1 / psy_rd=1.00:0.00 / mixed_ref=0 / me_range=16 / chroma_me=1 / trellis=1 / 8x8dct=1 / cqm=0 / deadzone=21,11 / fast_pskip=0 / chroma_qp_offset=-2 / threads=18 / sliced_threads=0 / nr=0 / decimate=1 / interlaced=0 / constrained_intra=0 / bframes=3 / b_pyramid=2 / b_adapt=1 / b_bias=0 / direct=3 / weightb=1 / open_gop=0 / weightp=0 / keyint=250 / keyint_min=25 / scenecut=40 / intra_refresh=0 / rc=2pass / mbtree=0 / bitrate=2910 / ratetol=1.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / cplxblur=20.0 / qblur=0.5 / ip_ratio=1.40 / pb_ratio=1.30 / aq=1:1.00 Default : Yes Forced : No Audio ID : 2 Format : AC-3 Format/Info : Audio Coding 3 Mode extension : CM (complete main) Codec ID : A_AC3 Duration : 1h 5mn Bit rate mode : Constant Bit rate : 256 Kbps Channel(s) : 2 channels Channel positions : Front: L R Sampling rate : 48.0 KHz Bit depth : 16 bits Compression mode : Lossy Stream size : 121 MiB (8%) Language : English Default : Yes Forced : No Being new to ffmpeg, I'm not sure what the error means or how to correct it. Thanks!

  Read the article

• How to re-add RAID-10 dropped drive?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• GRUB is not Booting Correctly

  - by msknapp

  I have a PC with three hard disks. Windows 7 is installed on the first, Ubuntu 14.04 is installed on the third. After I re-booted, it went straight to Windows 7. So I tried explicitly telling my PC to boot using the third hard disk, but that just takes me to the grub rescue prompt. I followed Scott Severence's instructions here to try and recover. Essentially, I updated grub, reinstalled grub, and then updated it again. After re-booting, absolutely nothing had changed. So instead I tried using the boot-repair tool. In the past it had failed for me, saying that I had programs running and it could not unmount drives, when I was running nothing. I never figured out how to solve that problem, but it went away when I bought another hard drive and used that for my Ubuntu installation, I don't know why. In any case, I ran the boot-repair tool and this time it said it was successful. First time for everything right? I re-booted, only to be taken straight to the grub rescue prompt. So I changed my BIOS settings to use the third hard disk for boot start up. That is the same hard drive where I have Ubuntu and grub installed, and the same one that the grub-repair tool told me to use. It still took me straight to the grub rescue prompt. So I went from not being able to boot Ubuntu, to not being able to boot either OS installed on my system. Thanks boot-repair! Boot repair gave me this URL for future troubleshooting: http://paste.ubuntu.com/8131669 When I try to boot from the third hard disk, this is my console: Loading Operating System ... error: attempt to read or write outside of disk 'hd0'. Entering rescue mode... grub rescue> grub rescue> set cmdpath=(hd0) prefix=(hd0,gpt2)/boot/grub root=hd0,gpt2 grub rescue> ls (hd0) (hd0,gpt3) (hd0,gpt2) (hd0,gpt1) (hd1) (hd2) (hd2,gpt2) (hd2,gpt1) (hd3) Those values look correct to me. I have also experimented with changing some of those values, but 'insmod normal' always throws the same error. Somebody please tell me how to fix this. I have tried everything, reinstalling grub, and running boot-repair. =========================== Update: I think the problem might be that the ubuntu installer did not partition my hard disk correctly. I booted from live USB and then launched gparted and looked at how it partitioned things. This is what gparted says: Partition, File System, Size, Used, Unused, Flags /dev/sda1 (!), unknown, 1.00 MiB, ---, ---, bios_grub /dev/sda2, ext4, 2.71 TiB, 47.30 GiB, 2.67 TiB, /dev/sda3, linux-swap, 16.00 GiB, 0.00 B, 16.00 GiB, So that first line looks problematic. It is supposed to be the /boot partition. However, it was given only 1 MiB? I am assuming that MiB is actually supposed to mean megabyte, no idea why that 'i' is there. It also says the file system is unknown. I read the answer by andrew here, and he says he had to do a custom install, explicitly configuring the boot partition. So I think that maybe Ubuntu's installer has a bug in it, where it does not set up the boot partition correctly if you are not installing on the first hard disk in your computer. I am going to try reinstalling with a custom partition scheme. I read elsewhere (askubuntu won't let me post another link) that I don't even need a /boot partition any more. So instead of following Andrew's instructions ver batim, I'm first going to try having just two partitions: one for /, and another for my 16GB swap space. Both as primary partitions. The first will be formatted as ext4. If that doesn't work, I may try again using /boot. ======================== So I did my custom install with no /boot partition, and it did not work. When I rebooted, I had an error message saying that some address did not exist. So for the hundredth time, I booted from the live USB, and ran boot-repair. Now I get this message GPT detected. Please create a BIOS-Boot partition (>1MB, unformatted filesystem, bios_grub flag). This can be performed via tools such as Gparted. Then try again. I feel like I'm running in circles and nobody will help me.

  Read the article

• Why do ICMP Redirct Host happen?

  - by El Barto

  I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Why do ICMP Redirect Host happen?

  - by El Barto

  I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Prevent auto mounting Android sdcard under Linux Mint

  - by BullShark

  I recently obtained an older Android phone, so that I could test Android Apps on it. I've needed it because I have a Nexus 7 but not older Android versions, hardware, etc. to test on. I'm having a problem with it under Linux Mint with Cinnamon. When I plug the phone in, or remove and plug the sdcard from the phone back to it while the phone is plugged in, Linux automatically mounts the sdcard. This is a problem because once it is mounted under Linux, it dismounts from the phone running Android 2.3.5, and I can no longer test Android Apps I write that require the sdcard to be present, writable. I went to Menu System Tools System Settings System Details Removable Media, and it brings up this window. I have changed the settings to always "Ask what to do" on "Select how media should be handled". However, the sdcard still gets mounted and then I am asked how I want to open these files (media players, photo importers, file browser, etc.). If I click the checkbox for "Never prompt or start programs on media insertion", then the sdcard is mounted, and I am not asked how to open these files. Eject is just a noob word for Ubuntu users that means umount (unmount) like "Adminstrator" is another ubuntu noob word for the root user. And if I unmount the sdcard, the phone doesn't recognize it again until I take the sdcard out and plug it back in. The phone sees it for a brief moment until Linux Mint takes it over. There are 2 possible solutions and maybe more: 1) Prevent Linux from automounting sdcards some how 2) Tell Android not to allow the computer it is plugged into to take over the sdcard, HOW? Edit: I found out how to prevent the sdcard from being automatically mounted: Now it gets recognized by Linux: bullshark@beastlinux ~ $ dmesg | tail -n 25 [597212.218323] sd 21:0:0:0: [sde] Attached SCSI removable disk [597212.218639] sr 21:0:0:1: Attached scsi CD-ROM sr2 [597212.218910] sr 21:0:0:1: Attached scsi generic sg7 type 5 [597217.139373] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597217.140726] sd 21:0:0:0: [sde] No Caching mode page present [597217.140735] sd 21:0:0:0: [sde] Assuming drive cache: write through [597217.143595] sd 21:0:0:0: [sde] No Caching mode page present [597217.143602] sd 21:0:0:0: [sde] Assuming drive cache: write through [597217.152240] sde: sde1 [597389.751008] 4:2:1: cannot get freq at ep 0x84 [597390.238742] 4:2:1: cannot get freq at ep 0x84 [597624.903132] sde: detected capacity change from 1977614336 to 0 [597637.677763] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597637.679616] sd 21:0:0:0: [sde] No Caching mode page present [597637.679626] sd 21:0:0:0: [sde] Assuming drive cache: write through [597637.682508] sd 21:0:0:0: [sde] No Caching mode page present [597637.682515] sd 21:0:0:0: [sde] Assuming drive cache: write through [597637.692758] sde: sde1 [597661.857979] sde: detected capacity change from 1977614336 to 0 [597688.775455] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597688.776814] sd 21:0:0:0: [sde] No Caching mode page present [597688.776823] sd 21:0:0:0: [sde] Assuming drive cache: write through [597688.780055] sd 21:0:0:0: [sde] No Caching mode page present [597688.780062] sd 21:0:0:0: [sde] Assuming drive cache: write through [597688.788639] sde: sde1 bullshark@beastlinux ~ $ However, the phone still unmounts the sdcard upon being detected by Linux. Linux detects but does not mount, and a few seconds later: Edit #2 (Solution): I solved this one by changing the usb connection type (was usb mass storage) :

  Read the article

• Issues with LVM partition size in Server 13.04

  - by Michael

  I am new to ubuntu and a little confused about how hard drive partitions and LVM works. I remember setting up Ubuntu server 13.04 and telling to to use 1TB of a 3TB server. Well I have maxed that out with blu-ray rips and want the rest of the drive for space. On log-in it says: System load: 2.24 Processes: 179 Usage of /: 88.7% of 912.89GB Users logged in: 0 Memory usage: 6% IP address for p5p1: 192.168.0.100 Swap usage: 0% => / is using 88.7% of 912.89GB lvdisplay outputs: --- Logical volume --- LV Path /dev/DeathStar-vg/root LV Name root VG Name DeathStar-vg LV Write Access read/write LV Creation host, time DeathStar, 2013-05-18 22:21:11 -0400 LV Status available # open 1 LV Size 2.70 TiB Current LE 707789 Segments 2 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Path /dev/DeathStar-vg/swap_1 LV Name swap_1 VG Name DeathStar-vg LV Write Access read/write LV Creation host, time DeathStar, 2013-05-18 22:21:11 -0400 LV Status available # open 2 LV Size 3.75 GiB Current LE 959 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1 vgdisplay outputs: VG Name DeathStar-vg System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 2.73 TiB PE Size 4.00 MiB Total PE 715335 Alloc PE / Size 708748 / 2.70 TiB Free PE / Size 6587 / 25.73 GiB df outputs: Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/DeathStar--vg-root 957238932 848972636 59634696 94% / none 4 0 4 0% /sys/fs/cgroup udev 1864716 4 1864712 1% /dev tmpfs 374968 1060 373908 1% /run none 5120 4 5116 1% /run/lock none 1874824 148 1874676 1% /run/shm none 102400 24 102376 1% /run/user /dev/sda2 234153 56477 165184 26% /boot And fdisk /dev/sda -l outputs: Disk /dev/sda: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 4294967295 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. I just don't know what to make of all this and am not sure how I can make it use all 2.73TBs. Thanks in advance for any help. EDIT-- Yes I did make changes to the LVM Config, but it didnt do anything. As requested, output of parted -l /dev/sda Model: ATA WDC WD30EFRX-68A (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2097kB 1049kB bios_grub 2 2097kB 258MB 256MB ext2 3 258MB 3001GB 3000GB lvm Model: ATA WDC WD30EFRX-68A (scsi) Disk /dev/sdb: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/DeathStar--vg-swap_1: 4022MB Sector size (logical/physical): 512B/4096B Partition Table: loop Number Start End Size File system Flags 1 0.00B 4022MB 4022MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/DeathStar--vg-root: 2969GB Sector size (logical/physical): 512B/4096B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2969GB 2969GB ext4

  Read the article

• How can I make my primary partition larger?

  - by Hjke123

  Well i'm running 2 different distro's of linux right now and I decided to make my ubuntu partition my primary partition larger so I took 119.53 GiB out of my other distro's partition and it became unallocated and then I figured Gparted would when I right click on it to resize/move give me the option of using it to make another partition bigger but it did not so I went google searching online and in one post I saw it said you had to format the unallocated space so I formatted it to ext4 the same as my primary partition but still no options to add it to any thing what do I do?

  Read the article

• raid md device is not remove from memory, how to overcome this problem

  - by santhosha

  i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

  Read the article

• How can I fix my corrupted RAID1 ext4 partition on a Synology DS212 NAS?

  - by Neil

  I have two identical 3 TB disks that were in a RAID1 array, where one disk crashed. I replaced the failed disk, but not after the RAID partitions got messed up. I need to figure out how to restore the RAID array and get at my ext4 partition. Here are the properties of the surviving disk: # fdisk -l /dev/sda fdisk: device has more than 2^32 sectors, can't use all of them Disk /dev/sda: 2199.0 GB, 2199023255040 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 267350 2147483647+ ee EFI GPT # parted /dev/sda print Model: ATA ST3000DM001-9YN1 (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 131kB 2550MB 2550MB ext4 raid 2 2550MB 4698MB 2147MB linux-swap(v1) raid 5 4840MB 3001GB 2996GB raid I replaced the failed drive, and cloned the surviving drive to it so I have something to work with. I cloned the drives with dd if=/dev/sdb of=/dev/sda conv=noerror bs=64M, and now /dev/sda and /dev/sdb are identical. Here is the RAID information: # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md1 : active raid1 sdb2[1] 2097088 blocks [2/1] [_U] md0 : active raid1 sdb1[1] 2490176 blocks [2/1] [_U] unused devices: <none> It seems that md2 is missing. Here is what testdisk 6.14-WIP finds: Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Current partition structure: Partition Start End Size in sectors 1 P Linux Raid 256 4980735 4980480 [md0] 2 P Linux Raid 4980736 9175039 4194304 [md1] Invalid RAID superblock 5 P Linux Raid 9453280 5860519007 5851065728 5 P Linux Raid 9453280 5860519007 5851065728 # After a quick search Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Partition Start End Size in sectors D MS Data 256 4980607 4980352 [1.41.12-2197] D Linux Raid 256 4980735 4980480 [md0] D Linux Swap 4980736 9174895 4194160 D Linux Raid 4980736 9175039 4194304 [md1] >P MS Data 9481056 5858437983 5848956928 [1.41.12-2228] And listing the files on the last partition in the list shows all of my files intact. What should I do?

  Read the article

• Secondary IP (eth0:0) acts like main server IP

  - by George Tasioulis

  I have a CentOS server, configured with 4 consecutive IPs: eth0 5.x.x.251 eth0:0 5.x.x.252 eth0:1 5.x.x.253 eth0:2 5.x.x.254 The problem is that all traffic goes out to the internet with eth0:0 (5.x.x.252) as the source IP, instead of eth0. # curl ifconfig.me 5.x.x.252 How can I fix this, so that all traffic goes out via eth0, ie my main IP? PS: My server is VPS running on a Xen dom0, the latter being configured in routed mode networking. Thanks in advance! Server configuration # ifconfig eth0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.251 Bcast:5.x.x.255 Mask:255.255.255.255 inet6 addr: fe80::x:x:x:x/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14675569 errors:0 dropped:0 overruns:0 frame:0 TX packets:9463227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4122016502 (3.8 GiB) TX bytes:25959110751 (24.1 GiB) Interrupt:23 eth0:0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.252 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:1 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.253 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:2 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.254 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 # cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 5.x.x.251 [fqdn] [hostname] # cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.251 NETMASK=255.255.255.224 SCOPE="peer 5.x.y.82" # cat ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.252 NETMASK=255.255.255.224 # cat route-eth0 ADDRESS0=0.0.0.0 NETMASK0=0.0.0.0 GATEWAY0=5.x.y.82 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 5.x.y.82 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 5.x.x.224 0.0.0.0 255.255.255.224 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 5.x.y.82 0.0.0.0 UG 0 0 0 eth0

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Degraded RAID-5 array with lvm2 lost superblock and partition table

  - by Fred Phillips

  I have a RAID-5 array of 4x1TB hard disks with one lvm2 partition on Ubuntu Linux 10.04 LTS. One of the disks has failed. I have re-assembled the array without this failed disk but now mdadm --examine claims the array has no superblock and fdisk says it has no partition table. What can I do to recover the data? # mdadm -D /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sat Mar 5 14:43:49 2011 Raid Level : raid5 Array Size : 2930276352 (2794.53 GiB 3000.60 GB) Used Dev Size : 976758784 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Sat Mar 5 15:06:49 2011 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Name : boba:1 (local to host boba) UUID : 52eb4bc9:c3d8aab5:e0699505:e0e1aa05 Events : 18 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 65 1 active sync /dev/sde1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 17 - faulty spare /dev/sdb1 # mdadm --examine /dev/md0 mdadm: No md superblock detected on /dev/md0. # fdisk -l /dev/md0 Disk /dev/md0: 3000.6 GB, 3000602984448 bytes 2 heads, 4 sectors/track, 732569088 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1572864 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10] md0 : active raid5 sdb1[4](F) sda1[0] sdd1[2] sde1[1] 2930276352 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_] unused devices: <none>

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >