Search Results

Search found 13968 results on 559 pages for 'device dependent routing'.

Page 30/559 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• com0com silent install (test signed com0com.sys shows up as signed in explorer but not in Device Manager)

  - by Andrew

  My goal is to have the com0com serial driver install without popping up the install wizard on both WinXP and Win2000. I am working on WinXP x86. I have followed the test signing instructions for the com0com driver, replacing amd64 with i386 at line 60. I have added my test certificate as both a root and trustedprovider using the following commands: certmgr /add com0com.cer /r localMachine root certmgr /add com0com.cer /r localMachine trustedprovider And verified that it is listed under both locations. I then run the newly built setup.exe. This installs the signed com0com.sys file into C:\WINDOWS\system32\DRIVERS and sets up a pair of virtual serial ports and a bus between them. Using explorer, I go to the DRIVERS directory, right click on the com0com.sys file and verify that it has the "test" digital signature. I then go into Device Manager, open the "com0com serial port emulators" entry, pick an entry and do Properties-Driver and see that it says "Not digitally signed". I click details for the driver and can see that it is referring to the com0com.sys driver file that I just confirmed is signed. I found what might be a related issue but I'm not sure. Does WinXP demand a WHQL signature? If so, does that explain why the com0com.sys file is signed but the device driver entries say they aren't signed?

  Read the article

• USB mouse does not work on boot

  - by Uku Loskit

  My problem is pretty much a duplicate of the one described in USB mouse late to load , but the solution there has not worked for me. I'm running the same OS and experiencing the exact same issue. It disappears after 10 seconds or so. Booting with the options specified in the other question did not fix it :/ Thanks in advance. sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver [114025.224407] usb 3-1: USB disconnect, address 2 sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver

  Read the article

• How can I make QSSTV recognise my sound device

  - by hellocatfood

  After reading this article from Instructables I wanted to try it out in Ubuntu. Luckily QSSTV is available but I'm having problems getting it to work properly. When pressing the green light (to receive data) I get this error: After going to Options Configure Interfaces I discovered that it's attempting to use /dev/dsp which doesn't appear to exist. In my /dev folder there are no files that reference sound devices and I've tried all of the devices in /dev/snd but unfortunately none of them work. Is there a specific audio device that I should be linking to?

  Read the article

• No space on device

  - by user170810

  Today I tried to move a huge directory to a common directory for 2 users. I first tried to change the permissions of my home directory. So something happened with my ~/.private directory and the disk was full! I have a 2 TB disk. I cannot make a backup, I cannot even enter graphics mode. Please help. Are there a way to restore my contents without making backup? Even creating ~/Private is impossible -- "no space on the device". I have no Private, and don't tell me that I have erased it, because it is not true. Are there some utilities to restore the files and make them not encrypted?

  Read the article

• How to detect webcam?

  - by Vishwas

  I installed Cheese but it is not yet possible for me to work with my webcam. After running lsusb I get this: Bus 007 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 044e:3012 Alps Electric Co., Ltd Bus 003 Device 004: ID 044e:3013 Alps Electric Co., Ltd Bus 003 Device 003: ID 044e:3010 Alps Electric Co., Ltd Bluetooth Adapter Bus 003 Device 002: ID 044e:3011 Alps Electric Co., Ltd Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 05ca:1839 Ricoh Co., Ltd Visual Communication Camera VGP-VCC6 [R5U870] Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Tell me what should I do now?

  Read the article

• Speed up Banshee's indexing of files on a device

  - by Stefano Palazzo

  I've got an external hard drive with music on it, around 250 albums. To make it work nicely with Banshee, I've created an .is_audio_player file on the device, containing audio_folders=Music. Every time I plug it in, Banshee takes around two minutes to index the thing, slowly building up the library - and being unusably sluggish while doing that. Is there, per chance, any way to speed it up? Should I not mount the hard disk as a music player, but add it's contents to my library? And, if I do, won't that give me lots of annoying X symbols next to the titles, as they can't be found sometimes? What's the best way to have my library on an external HDD?

  Read the article

• AndEngine doesn't fill correctly an image on my device

  - by Guille

  I'm learning about AndEngine a little bit, I'm trying to follow a tutorial but I don't get to fill the background image correctly, so, it's just appear in one side of my screen. My device is a Galaxy Nexus (1270x768 I think...). The image is 800x480. The code is: public EngineOptions onCreateEngineOptions() { camera = new Camera(0, 0, 800, 480); EngineOptions engineOptions = new EngineOptions(true, ScreenOrientation.LANDSCAPE_FIXED, new FillResolutionPolicy(), this.camera); engineOptions.getAudioOptions().setNeedsMusic(true).setNeedsSound(true); engineOptions.getRenderOptions().setMultiSampling(true);//.getConfigChooserOptions().setRequestedMultiSampling(true); engineOptions.setWakeLockOptions(WakeLockOptions.SCREEN_ON); return engineOptions; } I have been trying with several values in the camera, but it doesn't fill in all the screen, why?

  Read the article

• USB-creator: Error erasing device: Unknown or unsupported erase type

  - by Mike Williamson

  I created a live usb using usb-creator-gtk. I installed Ubuntu with it and all was good with the world. Now I am trying to use the same memory stick and create a live USB for 14.04 and I get the following error when trying to erase the disk. org.freedesktop.DBus.Python.gi._glib.GError: Traceback (most recent call last): File "/usr/lib/python3/dist-packages/dbus/service.py", line 707, in _message_cb retval = candidate_method(self, *args, **keywords) File "/usr/share/usb-creator/usb-creator-helper", line 239, in Format block.call_format_sync('dos', GLib.Variant('a{sv}', {'erase': GLib.Variant('s', '')}), None) gi._glib.GError: GDBus.Error:org.freedesktop.UDisks2.Error.Failed: Error erasing device: Unknown or unsupported erase type `' How can I fix this so I can create a new live USB?

  Read the article

• Xen 4.0.1 not booting with device not found error

  - by Disco

  I'm trying to get Xen 4.0.1 run as dom0 on a fresh/clean install of 10.10 desktop (x64). Followed the step by step tutorial at http://wiki.xensource.com/xenwiki/Xen4.0 I have the pvops kernel in /boot, also included the ext4 fs support by recompiling the kernel by : make -j6 linux-2.6-pvops-config CONFIGMODE=menuconfig make -j6 linux-2.6-pvops-build make -j6 linux-2.6-pvops-install Here's my grub entry : menuentry 'Xen4' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 insmod ext3 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set 2bf3177a-92fd-4196-901a-da8d810b04b4 multiboot /xen-4.0.gz dom0_mem=1024M loglvl=all guest_loglvl=all module /vmlinuz-2.6.32.27 root=UUID=2bf3177a-92fd-4196-901a-da8d810b04b4 ro module /initrd.img-2.6.32.27 } blkid /dev/sda1 gives the : /dev/sda1: UUID="2bf3177a-92fd-4196-901a-da8d810b04b4" TYPE="ext3" My partition shemes is : /boot (ext3) / (ext4) Whatever option i've tried i end up with : mounting none on /dev failed: no such file or directory And message complaining that it cannot find the device with uuid ... It's taking my hairs out, if somone has a clue ...

  Read the article

• usb hub not working on resume from suspend

  - by user1781498

  All the usb ports on my laptop work but when I resume from suspend some the usb ports don't work. lsusb Before Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 04f2:b3a6 Chicony Electronics Co., Ltd Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsusb After Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Stream audio to mobile device

  - by blackn1ght

  I'd like to stream the audio from Ubuntu 10.10 to my HTC Desire HD (Android 2.2). I've seen solutions so far for streaming from audio players, but I'd like to stream any audio output from the PC to my phone. My use case is for watching TV/Films in VLC or online (BBC iPlayer) in bed, without having to use my surround sound system which is likely to wake up my house mates. I'm not just talking about music from Banshee, but any audio that the system makes. I was thinking that PulseAudio is pretty powerful, is it possible to route audio through that to a mobile device? Can it be done through bluetooth? Cheers in advance!

  Read the article

• How To Create a Full Android Phone or Tablet Backup Without Rooting or Unlocking Your Device

  - by Chris Hoffman

  Android includes a built-in way to back up and restore the contents of your phone or tablet. All you need is a computer and a device running Android 4.0 (Ice Cream Sandwich) or newer. We’ve also covered backing up and restoring your Android phone with Titanium Backup. Titanium Backup is a great app, but it requires rooting your Android. This feature isn’t exposed in Android’s user interface, so you should consider it experimental. 8 Deadly Commands You Should Never Run on Linux 14 Special Google Searches That Show Instant Answers How To Create a Customized Windows 7 Installation Disc With Integrated Updates

  Read the article

• Developer Webinar Today: "Writing Solaris 11 Device Drivers"

  - by user13333379

  Oracle's Solaris Organization is pleased to announce a Technical Webinar for Developers on Oracle Solaris 11: "Writing Solaris 11 Device Drivers" By Bill Knoche (Principal Software Engineer) today June 5, 2012 9:00 AM PDT This bi-weekly webinar series (every other Tuesday @ 9 a.m. PT) is designed for ISVs, IHVs, and Application Developers who want a deep-dive overview about how they can deploy Oracle Solaris 11 into their application environments. This series will provide you the unique opportunity to learn directly from Oracle Solaris ISV Engineers and will include LIVE Q&A via chat with subject matter experts from each topic area. Any OTN member can register for this free webinar here. 

  Read the article

• How to Root Your Android Device & Why You Might Want To

  - by Chris Hoffman

  You’ve probably heard of people “rooting” their Android phones. If you’ve ever wondered how to do that yourself – or wondered why people would bother – you’re in luck. You can root your Android in just a few minutes. After rooting your device, you have full access to the entire system and can run special types of apps that require root permissions. These apps can disable bloatware, control app permissions, enable tethering, and do lots of other cool things. HTG Explains: Why Linux Doesn’t Need Defragmenting How to Convert News Feeds to Ebooks with Calibre How To Customize Your Wallpaper with Google Image Searches, RSS Feeds, and More

  Read the article

• today's multi-device world for web development

  - by paul smith

  With the huge explosion of mobile devices and addition of HTML5/CSS3, there seems to be a shift towards "responsive" designs (i.e., adapting to smaller screen sizes) which seems to be achieved using CSS3's Media Queries. My question is, given the current need of adapting to both desktop and mobile, is it common practice to actually organize two versions of your website (one for desktop and one for mobile)? Or is there just one version with different css files for targeting different devices and screens? Handling just cross-browser (ie6, ff3, opera9, etc...) HTML4/5, CSS2/3 was already hard enough, but now we're expected to handle cross-device (phone, tablet, etc...) as well, so my assumption is company's would create a separate project for mobile and redirect based on the user agent, but this is just a guess.

  Read the article

• Handheld device software - Handheld tuners?

  - by NathanH

  Hey I've been looking around and really don't understand what software some of these company's use for their handheld devices. I've used a lot of Handheld Tuners (Cobb Accessport, Diablo Sport). I've gotten more and more knowledgable of programming and I'm really wanting to understand what software they use on these devices to have a graphical interface. And to hold all the files to flash over to the ecu. I'm just unsure how you would get basically all the components to work together (screen, buttons, memory) without having drivers installed. I could be totally wrong here on using the term drivers, but that's what I would like some help to get more knowledge on (only thing I've really found is making a handheld game boy from scratch,but that was using a emulator.). I've tried looking it up but can't really find a good write up or explanation anywhere I look. Just really would like to put a little device together and have a simple user interface and work from there. Thanks, Nathan

  Read the article

• DVC101 Video Capture Device on USB hub - Ubuntu Server 12.04

  - by John

  I have a Dell Inspiron 8600 laptop I use as a media server/video capture system. It only has 2 USB ports and I have a total of 3 devices I need to connect. The DVC101 works perfectly while plugged directly into the USB port in back of the laptop. Unfortunately it does not get recognized when plugged into a passive or powered USB hub. Questions: Is there something I am missing on the Ubuntu side? Something I need to do that will allow the device to be recognized through the hub? If not, will the extra USB ports on a dell laptop dock (port replicator) act the same as the aftermarket hubs? I know this one is off topic of Ubuntu but any input appreciated.

  Read the article

• Grub can't find device on boot resulting in Grub Rescue

  - by user1160163

  So I have 2 hard drives a HDD 320GB and a SSD 20GB. Before I had Windows 7 on the HDD and Ubuntu on the SSD but wanted to get rid of windows and reinstall a clean Ubuntu on the SSD then use the HDD for storage. So I deleted everything from the HDD and set up the SSD with 18GB ext4 and 2GB Swap and installed Ubuntu on the 18GB ext4. Though now when I boot up I get "Error: No such device Grub Rescue" I have a live USB and I ran the Boot Repair following these instructions - grub rescue after install of Ubuntu 12.04 (dual boot) - it says successful though still have the same problem. This is the given URL from Boot Repair - http://paste.ubuntu.com/1257988/ Thanks for any help given.

  Read the article

• How to route between 2 networks with a server with 2 network cards?

  - by LumenAlbum

  This is the first time I am faced with routing and it seems I have hit a dead end. I have the following scenario: client1: 192.168.1.10 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 client2: 192.168.1.20 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 server (Windows Server 2008 R2 with enabled RAS & Routing Services) network card 1 (connected to a switch along with the clients) 192.168.1.100 255.255.255.0 DNS server: 127.0.0.1 network card 2 (connected to the router) 192.168.2.100 255.255.255.0 gateway: 192.168.2.1 DNS server: 127.0.0.1 (DNS forwarding to 192.168.2.1) ISP router (with connection to internet) 192.168.2.1 Now in this scenario I have tried to route traffic from the 192.168.1.0/24 network with the clients to the 192.168.2.0/24 network with the routers to connect them to the internet. However, no matter what I do I get no positive ping to the router 192.168.2.1. Ping from 192.168.168.1.10 to 192.168.1.20: Success to 192.168.1.100: Success to 192.168.2.100: Success to 192.168.2.1: not reachable The routing table contains the 2 routes 192.168.1.0 and 192.168.2.0 as directly connected. Does anyone know where the routing fails? I have searched different forums but mostly found nothing relevant. One post however pointed out that in a similar situation the problem was that the router doesn't know the way back and the internet router would need a static route back to the first router. If that really is the case, I take it there is no solution with my equipment, because the standart ISP router doesn't allow to set any static routes.

  Read the article

• NetworkManager doesn't detect my broadband device

  - by Joril

  I have a Huawei K3765 (USB ID 12D1:1520) and I'm trying to use it with Ubuntu 10.04 Lucid. I have usb-modeswitch installed, so when I plug the device I can see that it gets switched from storage-mode to modem-mode. My problem is that when I try to create a broadband mobile connection for it, NetworkManager doesn't detect the modem... I tried this on two different laptops. /var/log/daemon.log doesn't show anything of interest, AFAIKT... What could I try?

  Read the article

• Independent sound device for headphones

  - by amfcosta

  I have an Asus K52Jc and in sound configuration there is no independent sound device for the headphones, and so there's no way to have independent volume for speakers and headphones. Is there a way to have independent devices? Or is this hardware specific? lshw reports that I have an "Intel 5 Series/3400 Series Chipset High Definition Audio". aplay -l reports: placa 0: Intel [HDA Intel], dispositivo 0: CONEXANT Analog [CONEXANT Analog] Subdispositivos: 1/1 Subdispositivo #0: subdevice #0 placa 0: Intel [HDA Intel], dispositivo 3: HDMI 0 [HDMI 0] Subdispositivos: 1/1 Subdispositivo #0: subdevice #0

  Read the article

• The device is not ready

  - by hmloo

  When you retrieve the drive info using the DriveInfo class, if you don't use the IsReady property to test whether a drive is ready, it will throw error as "The device is not ready". so you must use IsReady property to determines if the drive is ready to be queried, written to, or read from. The following code example demonstrates querying information for all drives on current system. using System; using System.IO; class Test { public static void Main() { DriveInfo[] allDrives = DriveInfo.GetDrives(); foreach (DriveInfo d in allDrives) { Console.WriteLine("Drive {0}", d.Name); Console.WriteLine(" File type: {0}", d.DriveType); if (d.IsReady == true) { Console.WriteLine(" Volume label: {0}", d.VolumeLabel); Console.WriteLine(" File system: {0}", d.DriveFormat); Console.WriteLine( " Available space to current user:{0, 15} bytes", d.AvailableFreeSpace); Console.WriteLine( " Total available space: {0, 15} bytes", d.TotalFreeSpace); Console.WriteLine( " Total size of drive: {0, 15} bytes ", d.TotalSize); } } } }

  Read the article

• No such device = Grub Rescue 13.10

  - by LittleBeard

  Noob here. I just installed 13.10 yesterday And it booted up for me several times and all was well. Then this morning when I went to boot I received a "No such device" error and a "grub rescue" command line prompt. I tried running the live disc and re-installing Ubuntu 13.10 However that was a fail. The same messages kept occurring. Then I tried to boot up in Windows 7. Also a fail. I then attempted to run a Windows 7 restore disc. You guessed it - Fail. This sucks. What do I do?

  Read the article

• What's involved in resetting the graphics device?

  - by Donutz

  I'm playing with XNA 4.0, VS2010. I've created a window (not maximized) and drawn some sprites. All is good until I resize the window, after which the sprites stop displaying or only partially display. I'm pretty sure it has something to do with needing to reset the device or something, but can't find any clear instructions or sample code. It's not just a case of needing to increase the preferredbackbuffer size, because even if I shrink the window I get this symptom. I've looked at the source code that I was able to get from Microsoft before they shut down XNA, but it doesn't actually explain anything. Any help or advice? If it makes any difference I'm creating DrawableGameComponents and doing my updates and drawing in their Draw/Update routines.

  Read the article

• USB audio device not detected [solved]

  - by user199052

  I've been having problems with USB sound for some time (it used to work about 6 months ago). I find that any USB sound device that I connect is not recognised, and is not listed by aplay -l I've tried disabling pulseaudio. I've tried purging and re-installing alsa-base, pulseaudio, and pavucontrol. To no avail. I'm using 12.04 LTS. I found the solution: 12.04 does not have the needed kernel module snd-usb-hiface this is introduced in the 3.11.1 kernel and installing that on 12.04 gives USB sound for my equipment. How to install the 3.11.1 kernel is given here:- installing 3.11.1 kernel

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >