Search Results

Search found 20062 results on 803 pages for 'malcolm post'.

Page 30/803 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

  • Computer does not boot, often

    - by tam
    I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

    Read the article

  • Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

    - by delta1
    I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

    Read the article

  • post values to external page explicitly PHP

    - by JPro
    Hi, I want to post values to a page through a hyperlink in another page. Is it possible to do that? Let's say I have a page results.php which has the starting line, <?php if(isset($_POST['posted_value'])) { echo "expected value"; // do something with the data } else { echo "no the value expected"; } If from another page say link.php I place a hyperlink like this: <a href="results.php?posted_value=1"> , will this be accepetd by the results page? If instead if I replace the above starting line with if(isset($_REQUEST['posted_value'])), will this work? I believe the above hyperlink evaluates to GET, but since the only visibility difference between GET and POST that is you can see parameters in the address bar with GET But, is there any other way to place a hyperlink which can post values to a page? or can we use jquery in the place of hyperlink to POST the values? Can anyone please suggest me something on this please? Thanks.

    Read the article

  • Is it possible to get multiple forms to work with one ajax post function

    - by Scarface
    Hey guys I have a system where there is one form for each friend you have and I used to have an ajax post function for each form, but I want to save code and was wondering if it was possible to get multiple forms to work with just one post function. If anyone has any advice on how to achieve this I would appreciate it. For example <div id="message"> <form id='submit' class='message-form' method='POST' > <input type='hidden' id='to' value='friend1' maxlength='255' > Subject<br><input type='text' id='subject' maxlength='50'><br> Message<br><textarea id='message2' cols='50' rows='15'></textarea> <input type='submit' id='submitmessage' class='responsebutton' value='Send'> </form> </div> $(document).ready(function(){ $(".message-form").submit(function() { $("#submitmessage").attr({ disabled:true, value:\"Sending...\" }); var to = $('#to').attr('value'); var subject = $('#subject').attr('value'); var message = $('#message2').attr('value'); $.ajax({ type: "POST", url: "messageprocess.php", data: 'to='+ to + '&subject=' + subject + '&message=' + message, success: function(response) { if(response == "OK") { $('.message-form').html("<div id='message'></div>"); $('#message').html("<h2>Email has been sent!</h2>") .append("<p>Please wait...</p>") .hide() .fadeIn(1500, function() { $('#message').append(\"<img id='checkmark' src='images/check.png' />\"); });

    Read the article

  • Sending an HTTP POST request through the android emulator doesn't work

    - by Sotirios Delimanolis
    I'm running a tomcat servlet on my local machine and an Android emulator with an app that makes a post request to the servlet. The code for the POST is below (without exceptions and the like): String strUrl = "http://10.0.2.2:8080/DeviceDiscoveryServer/server/devices/"; Device device = Device.getUniqueInstance(); urlParameters += URLEncoder.encode("user", "UTF-8") + "=" + URLEncoder.encode(device.getUser(), "UTF-8"); urlParameters += "&" + URLEncoder.encode("port", "UTF-8") + "=" + URLEncoder.encode(new Integer(Device.PORT).toString(), "UTF-8"); urlParameters += "&" + URLEncoder.encode("address", "UTF-8") + "=" + URLEncoder.encode(device.getAddress().getHostAddress(), "UTF-8"); URL url = new URL(strUrl); HttpURLConnection connection = (HttpURLConnection) url.openConnection(); connection.setDoOutput(true); connection.setRequestMethod("POST"); OutputStreamWriter wr = new OutputStreamWriter(connection.getOutputStream()); wr.write(urlParameters); wr.flush(); wr.close(); Whenever this code is executed, the servlet isn't called. However if I change the type of the request to 'GET' and don't write anything to the outputstream, the servlet gets called and everything works fine. Am I just not making the POST correctly or is there some other error?

    Read the article

  • Jquery - $.(post) data response not consistent with PHP

    - by Sasha
    Jquery code: var code = $('#code'), id = $('input[name=id]').val(), url = '<?php echo base_url() ?>mali_oglasi/mgl_check_paid'; code.on('focusout', function(){ var code_value = $(this).val(); if(code_value.length != 16 ) { if ($('p[role=code_msg]').length != 0 ) $('p[role=code_msg]').remove() ; code.after('<p role=code_msg>Pogrešan kod je unešen.</p>'); } else { if ($('p[role=code_msg]').length != 0 ) $('p[role=code_msg]').remove() ; $.post(url, {id : id, code : code_value}, function(data){ if(data != 'TRUE'){ code.after('<p role=code_msg>Uneti kod je neispravan.</p>'); } else { code.after('<p role=code_msg>Status malog oglasa je promenjen.</p>'); code.after(create_image()); code.remove(); } }); } }); PHP (Codeigniter) code: function mgl_check_paid() { $code = $this->input->post('code'); $id = $this->input->post('id'); echo ($this->mgl->mgl_check_paid($code, $id)) ? 'TRUE' : 'FALSE'; } Problem is following: When code is sent and if it is correct, PHP part will echo TRUE, and JS will execute ELSE part (after post), but for some reason it is not doing that (it is executing the first part of the statment)? What is wrong with this code?

    Read the article

  • How to update facebook status by http request

    - by Narjes
    I try to send http request like: ..."POST http://api.facebook.com/restserver.php?method=facebook.users.setStatus&api_key=762ec91e7987aaeaee7e2cdfdfcb3c30&call_id=$call_id&sig=$s&v=1.0&uid=1533439618&status=44 HTTP/1.1";.... but I receive nothing... in twitter I success: .. "POST ht tp://twitter.com/statuses/update.xml?status=123123 HTTP/1.1" ...

    Read the article

  • How to Link Sub Taxonomy to products in wordpress

    - by rahul251
    I have created custom post types called Internal products I Have a page page-internal-products.php which list all the custom taxonomy for the Custom post type Internal product On clicking on the taxonomies takes me to a page which lists the sub taxonomies for the particular parent taxonomy for which i have created the page called taxonomy-internalproducts_categories.php On clicking on the sub taxonomy. I need to go to a page which lists all the products for this sub taxonomy. How can I achieve this?

    Read the article

  • how to refresh mulitple divs when after posting using jquery

    - by oo
    i have a screen with multiple little widgets (all with different divs around them). i have one form and when i post (using jquery) right now it updates the single form using ajax. i want two other divs to refresh as well (that are outside the form). What is the best way to trigger a refresh of multiple different divs on a single jquery ajax post callback?

    Read the article

  • page sends file to curl i want to get download link insted

    - by Ben
    there is a page that i need to post a password to it and then i get a file to download. the post goes to the same page address its loads again and pop up the download manager. now i want to do the same but in curl, i posted the data to the url and then its sends me the file back but i dont want my script to download the whole file i want only to get a link to download it by myself. how can i do that?

    Read the article

  • how to write an artificial request.

    - by Bunny Rabbit
    how can i construct a artificial request to login to twitter or any site for that matter that accpets post forms. what i've been trying is to extract the headers and post request parameters from the origional request(directed at the action atribute of the form) and copy it to the outgoing url object that i am making.but it just won't work. And i am aware of the apis and i don't wanna use them i am trying this to write a web proxy site.

    Read the article

  • Extra GET Request on META Refresh Redirect (CGI-C)

    - by Koray Alkan
    I have a form (on page form.html) submitting with POST method to a CGI-C page - let's call it form.cgi - and what form.cgi does is it redirects the user to the previous page (to form.html) with appending query strings using HTTP-EQUIV Refresh META after 5 seconds. However, if I monitor the Web server's access.log although I see the appropriate POST request for form.cgi there is an additional GET request for form.cgi again, after 5 seconds just before redirecting the user to form.html Has anyone faced with such an issue?

    Read the article

  • Can I create an ASP.NET ImageButton that doesn't postback?

    - by Giffyguy
    I'm trying to use the ImageButton control for client-side script execution only. I can specify the client-side script to execute using the OnClientClick property, but how do I stop it from trying to post every time the user clicks it? There is no reason to post when this button is clicked. I've set CausesValidation to False, but this doesn't stop it from posting.

    Read the article

  • PHP: How to forward on $_FILES using cURL

    - by Toby
    Hi. I'm trying to use cURL to forward on a http request from a form in a web application I'm developing. Essentially I need to submit the same form twice on different servers, for the second server I'm adding some security measures to the post data. I can receive $_POST information on the second form perfectly fine, however I'm having major troubles with my $_FILES - I've tried separating the two so there's a separate request for post and files data but still no luck. Is this possible?

    Read the article

  • Pass data via ajax to dialog Jquery

    - by user342391
    I am trying to post data from my form to a jquery dialog that loads external content. I am serializing the form data which works (appears in the url) but the dialog won't open: $("#wavajax button").click(function() { $.post({url: 'player/index.php', data: $("#wavajax").serialize(), success: function (data) { $("#recordingdialog").load("player/index.php", [], function(){ $("#recordingdialog").dialog("open"); } }); return false; }); What am I doing wrong, am I going about it the right way???

    Read the article

  • JQuery AJAX syntax

    - by Nick
    I am trying to find the correct syntax to pass a varible to my JQuery Post. var id = empid; $.ajax({ type: "POST", url: "../Webservices/EmployeeService.asmx/GetEmployeeOrders", data: "{empid: empid}", contentType: "application/json; charset=utf-8", dataType: "json", success: function(result) { alert(result.d); } I don't think the data: value is quite right. Someone set me straight? Thanks!

    Read the article

  • empty() doesn't work with codeigniter input class

    - by BabyAzerty
    This is really weird. Whenever I call something like if(empty($this->input->post("foo")){//blabla} The whole PHP is "down" and I get a blank page from the website (even when I don't pass through this empty(input) line). I know this is not the right method and it is stupid, I change the code to if(!$this->input->post("foo")){//blabla} Better I guess ? Seriously, how come the empty(input) breaks down the entire PHP page ? (I can't get any echo "something").

    Read the article

  • Drupal JSON POST from PhoneGap

    - by abritez
    I am trying to send a POST request to Drupal's Services module & JSON_Server module, however I am getting { "#error": true, "#data": "Invalid method " } Since PhoneGap runs html files from locally on the phone, should i need to worry about JSONP. The issue I have with that is that I must POST data, and JSONP only allows for GET. Any ideas would be helpful. Thanks! //SEND REQUEST AND CALLBACK FUNCTION var req; DrupalService.prototype.request = function(dataObject, callback){ req = false; var url = DRUPAL_JSON_URL; var params = "data="+dataObject; try { req = new XMLHttpRequest(); } catch(e) { req = false; } if(req) { req.onreadystatechange = function() {//Call a function when the state changes. if(req.readyState == 4 && req.status == 200) { console.log(" "+req.responseText); } } req.open("POST", url, false); req.send(params); } }

    Read the article

  • Rails: savage_beast forum plugin and tinymce - new post works but edit doesn't use tinymce properly

    - by Max Williams
    Hi all. I'm using the savage_beast forum plugin and tinymce (via the tinymce_hammer plugin) in my rails app. When posting a new post, tinymce works fine. However, when i go to edit a post i get the tinymce editor, but the content in the edit box has all been converted into html. Can anyone tell me how i get it so that what appears in the tinymce edit box is the original text i posted, rather than the converted-to-html version? Does it need to get converted back from html into a format tinymce will use? Savage_beast saves the original given text in a body field, and the converted-to-html text in a body_html field. After tinymce does its work in the first instance (ie when posting a new post) the body field gets text that's already been converted to html. So i guess i need to convert it back to whatever tinymce expects? I'd expect tinymce to be happy with getting html, and to just handle it, though. grateful for any advice - max

    Read the article

  • jQuery .post gets null data

    - by Andrew Flusche
    Hey everyone. This is my first post here, so I hope I'm doing it appropriately. I have several jQuery $.post calls that work just fine. They send data to a PHP script that modifies a database and returns some data. No problem. But this one doesn't work. The returned data is just NULL. $.post("act_addTaskLog.php", {description: $("#logFormDescription").val(), complete: $("#logFormComplete").is(':checked'), taskId: $("#logFormTaskId").val(), user: <?php echo $_SESSION['user']; ?>}, function(data) { alert("data: " + data); } ); I've tried everything I can think of, to no avail. I've even tried just one line in my PHP script: die("true"); Firebug shows that the script is being executed, but it's not completing. The alert message displays just with the label "data:" in it, no actual data. Thanks in advance for your help!

    Read the article

  • http post with ant for file uploading

    - by paleozogt
    As part of my Ant build process, I'd like to upload files to a webserver via HTTP Post. Ant only comes with an HTTP Get task. However, Ant Contrib seems to have an HTTP Post task. The problem is that it doesn't have any authentication (like get does) or any way to specify a file upload (despite what the docs say, "rawFile" is not part of the distro). My question is: does Ant Contrib's Post task actually support what I want, but in a non-obvious way (perhaps I have to do it by hand)? Or is there some other way to do this?

    Read the article

  • Preventing $.POST hijack

    - by Jamie
    I'm currently building a facebook application. Lets say I have a variable $uid that identifies the user so I can store this in my database along with their submitted data. I pass $uid and $data via json encoded values using $.post. However, this doesn't prevent someone changing $uid to save data as someone else. I have been thinking about how to overcome this, so far I haven't found a solution apart from: create database with $uid $secretkey on first page load. When $.post send $secretkey with the post and then retrieve the $uid from the database. Would this be the correct approach to use?

    Read the article

  • Getting 401 on Twitter OAuth POST requests

    - by Baishampayan Ghose
    I am trying to use Twitter OAuth and my POST requests are failing with a 401 (Invalid OAuth Request) error. For example, if I want to post a new status update, I am sending a HTTP POST request to https://twitter.com/statuses/update.json with the following parameters - status=Testing&oauth_version=1.0&oauth_token=xxx& oauth_nonce=xxx&oauth_timestamp=xxx&oauth_signature=xxx& oauth_consumer_key=xxx&in_reply_to=xxx&oauth_signature_method=HMAC-SHA1` My GET requests are all working fine. I can see on the mailing lists that a lot of people have had identical problems but I could not find a solution anywhere. I am using the oauth.py Python library.

    Read the article

  • How to post HTML content in facebook wall using facebook api in php

    - by Elankeeran
    How to post HTML content in facebook wall using facebook api in php I have used below codes but not working $result = $facebook->api('/me/feed/','post',array( 'message' => '<h1>This is my demo Face book application!</h1>')); And I used as below code using php concatenate the HTML string $result = $facebook->api('/me/feed/','post',array( 'message' => 'This is my demo Facebook application!' . $htmlStr)); but not working and getting below error OAuthException: (#1) An unknown error occurred Any please help me.

    Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >