Search Results

Search found 5179 results on 208 pages for 'max magnus'.

Page 31/208 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• HP to Cisco spanning tree root flapping

  - by Tim Brigham

  Per a recent question I recently configured both my HP (2x 2900) and Cisco (1x 3750) hardware to use MSTP for interoperability. I thought this was functional until I applied the change to the third device (HP switch 1 below) at which time the spanning tree root started flapping causing performance issues (5% packet loss) between my two HP switches. I'm not sure why. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. I'd prefer the Cisco stack to act as the root. EDIT: There is one specific line - 'spanning-tree 1 path-cost 500000' in the HP switch 2 that I didn't add and was preexisting. I'm not sure if it could have the kind of impact that I'm describing. I'm more a security and monitoring guy then networking. EDIT 2: I'm starting to believe the problem lies in the fact that the value for my MST 0 instance on the Cisco is still at the default 32768. I worked up a diagram: This is based on every show command I could find for STP. I'll make this change after hours and see if it helps. Cisco 3750 Config: version 12.2 spanning-tree mode mst spanning-tree extend system-id spanning-tree mst configuration name mstp revision 1 instance 1 vlan 1, 40, 70, 100, 250 spanning-tree mst 1 priority 0 vlan internal allocation policy ascending interface TenGigabitEthernet1/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface TenGigabitEthernet2/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface Vlan1 no ip address ! interface Vlan100 ip address 192.168.100.253 255.255.255.0 ! Cisco 3750 show spanning tree: show spanning-tree MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 0004.ea84.5f80 Cost 200000 Port 53 (TenGigabitEthernet1/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32768 (priority 32768 sys-id-ext 0) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Root FWD 2000 128.53 P2p MST1 Spanning tree enabled protocol mstp Root ID Priority 1 Address a44c.11a6.7c80 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 1 (priority 0 sys-id-ext 1) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2000 128.53 P2p Cisco 3750 show logging: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up HP Switch 1: ; J9049A Configuration Editor; Created on release #T.13.71 vlan 1 name "DEFAULT_VLAN" untagged 1-8,10,13-16,18-23,A1-A4 ip address 100.100.100.17 255.255.255.0 no untagged 9,11-12,17,24 exit vlan 100 name "192.168.100" untagged 9,11-12,17,24 tagged 1-8,10,13-16,18-23,A1-A4 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A4 no ip address exit vlan 40 name "Cafe" tagged 1,4,7,A1-A4 no ip address exit vlan 250 name "Firewall" tagged 1,4,7,A1-A4 no ip address exit vlan 70 name "DMZ" tagged 1,4,7-8,13,A1-A4 no ip address exit spanning-tree spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 password manager password operator HP Switch 1 show spanning tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 363,490 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | Auto 128 Disabled | HP Switch 1 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00842 stp: MSTI 1 starved for an MSTI Msg Rx on port A4 from 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to ... HP Switch 2 Configuration: ; J9146A Configuration Editor; Created on release #W.14.49 vlan 1 name "DEFAULT_VLAN" untagged 1,3-17,21-24,A1-A2,B2 ip address 100.100.100.36 255.255.255.0 no untagged 2,18-20,B1 exit vlan 100 name "192.168.100" untagged 2,18-20 tagged 1,3-17,21-24,A1-A2,B1-B2 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A2,B2 no ip address exit vlan 40 name "Cafe" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 250 name "Firewall" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 70 name "DMZ" tagged 1,13-14,16,A1-A2,B2 no ip address exit logging 192.168.100.18 spanning-tree spanning-tree 1 path-cost 500000 spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 HP Switch 2 Spanning Tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 21,793 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : A1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 2000 IST Remaining Hops : 19 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Forwarding | 0024a8-cd6000 2 Yes No B2 | Auto 128 Disabled | HP Switch 2 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80 00839 stp: IST Root changed from 32768:0021f7-126580 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0004ea-845f80 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00435 ports: port B1 is Blocked by STP 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: IST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80

  Read the article

• How to use custom IComparer for SortedDictionary?

  - by Magnus Johansson

  I am having difficulties to use my custom IComparer for my SortedDictionary<. The goal is to put email addresses in a specific format ([email protected]) as the key, and sort by last name. When I do something like this: public class Program { public static void Main(string[] args) { SortedDictionary<string, string> list = new SortedDictionary<string, string>(new SortEmailComparer()); list.Add("[email protected]", "value1"); list.Add("[email protected]", "value2"); foreach (KeyValuePair<string, string> kvp in list) { Console.WriteLine(kvp.Key); } Console.ReadLine(); } } public class SortEmailComparer : IComparer<string> { public int Compare(string x, string y) { Regex regex = new Regex("\\b\\w*@\\b", RegexOptions.IgnoreCase | RegexOptions.CultureInvariant | RegexOptions.IgnorePatternWhitespace | RegexOptions.Compiled ); string xLastname = regex.Match(x).ToString().Trim('@'); string yLastname = regex.Match(y).ToString().Trim('@'); return xLastname.CompareTo(yLastname); } } I get this ArgumentException: An entry with the same key already exists. when adding the second item. I haven't worked with a custom IComparer for a SortedDictionary before, and I fail to see my error , what am I doing wrong?

  Read the article

• Is there a way of recover from an Exception in Directory.EnumerateFiles ?

  - by Magnus Johansson

  In .NET 4, there's this Directory.EnumerateFiles() method with recursion that seems handy. However, if an Exception occurs within a recursion, how can I continue/recover from that and continuing enumerate the rest of the files? try { var files = from file in Directory.EnumerateFiles(@"c:\", "*.*", SearchOption.AllDirectories) select new { File = file }; Console.WriteLine(files.Count().ToString()); } catch (UnauthorizedAccessException uEx) { Console.WriteLine(uEx.Message); } catch (PathTooLongException ptlEx) { Console.WriteLine(ptlEx.Message); }

  Read the article

• rand() generating the same number – even with srand(time(NULL)) in my main!

  - by Nick Sweet

  So, I'm trying to create a random vector (think geometry, not an expandable array), and every time I call my random vector function I get the same x value, thought y and z are different. int main () { srand ( (unsigned)time(NULL)); Vector<double> a; a.randvec(); cout << a << endl; return 0; } using the function //random Vector template <class T> void Vector<T>::randvec() { const int min=-10, max=10; int randx, randy, randz; const int bucket_size = RAND_MAX/(max-min); do randx = (rand()/bucket_size)+min; while (randx <= min && randx >= max); x = randx; do randy = (rand()/bucket_size)+min; while (randy <= min && randy >= max); y = randy; do randz = (rand()/bucket_size)+min; while (randz <= min && randz >= max); z = randz; } For some reason, randx will consistently return 8, whereas the other numbers seem to be following the (pseudo) randomness perfectly. However, if I put the call to define, say, randy before randx, randy will always return 8. Why is my first random number always 8? Am I seeding incorrectly?

  Read the article

• How to tell .htaccess to ignore a subdirectory (or, how to run WordPress and ExpressionEngine simult

  - by Mike Crittenden

  I have an ExpressionEngine site at http://example.com and a WordPress blog at http://example.com/blog ...the problem is, any WP pages that don't map directly to an index.php end up being handled by ExpressionEngine, which results in a 404. For example, http://example.com/blog and http://example.com/blog/wp-admin both work fine as they both directly use an index.php in those folders, but http://example.com/blog/category/tag/something gets handled by ExpressionEngine. So how can I modify the ExpressionEngine .htaccess file to tell it to ignore anything in the /blog directory? Here's what's currently in the ExpressionEngine .htaccess file: Options +FollowSymLinks RewriteEngine On ##### Remove index.php ###################################### RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ /index.php/$1 [L] ##### Add WWW ############################################### RewriteCond %{HTTP_HOST} ^getregionalcash.com [NC] RewriteRule ^(.*)$ http://www.getregionalcash.com/$1 [R=301,NC] ##### Increase File Limit Size ############################## #set max upload file size php_value upload_max_filesize 20M #set max post size php_value post_max_size 20M #set max time script can take php_value max_execution_time 6000000 #set max time for input to be recieved php_value max_input_time 6000000 #increase php memory limit php_value memory_limit 64M Any ideas?

  Read the article

• jquery ui slider IE7 bug...

  - by Reigel

  When you are holding the handles to slide them the width of the range blows out to 100% width, but snaps back to the width it's supposed to be once you release the handle. jQuery 1.4.2 UI 1.8.2 please help jQuery if ($("#topImageSlider").length){ var max = 120; var initialValue = 40; function refreshValue(){ //$('#sliderValue .current').text($("#topImageSlider").slider("value")); $('#sliderValue .current').text($('.ui-slider-range').width()); } $("#topImageSlider").slider({ orientation: 'horizontal', range: "min", max: max, min: 1, value: initialValue, slide: refreshValue, change: refreshValue }).after('<div id="sliderValue"><span class="current">'+ initialValue +'</span> / <span class="max">'+ max +'</span></div>'); } css #topImageSlider, #sliderValue { margin: 0 auto; width: 572px; text-align: center; } #topImageSlider { margin-top: 20px; background: url(../img/bg/slider.png) no-repeat; height: 5px; } #topImageSlider .ui-slider-range { background: url(../img/bg/slider-progress.gif) repeat-x; left: 2px; height: 5px; } #topImageSlider .ui-slider-handle { background: url(../img/btn/slider-handle.png) no-repeat; width: 24px; height: 24px; top: -8px; outline: 0; cursor: pointer; z-index: 999; } #sliderValue { margin-top: 10px; color: #bbb; font-weight: bold; } #sliderValue .current { color: #ff6e0d; }

  Read the article

• Use of qsrand, random method that is not random

  - by Andy M

  Hey everyone, I'm having a strange problem here, and I can't manage to find a good explanation to it, so I thought of asking you guys : Consider the following method : int MathUtility::randomize(int Min, int Max) { qsrand(QTime::currentTime().msec()); if (Min > Max) { int Temp = Min; Min = Max; Max = Temp; } return ((rand()%(Max-Min+1))+Min); } I won't explain you gurus what this method actually does, I'll instead explain my problem : I realised that when I call this method in a loop, sometimes, I get the same random number over and over again... For example, this snippet... for(int i=0; i<10; ++i) { int Index = MathUtility::randomize(0, 1000); qDebug() << Index; } ...will produce something like : 567 567 567 567...etc... I realised too, that if I don't call qsrand everytime, but only once during my application's lifetime, it's working perfectly... My question : Why ?

  Read the article

• Neural Networks in C# using NeuronDotNet

  - by kingrichard2005

  Hello, I'm testing the NeuronDotNet library for a class assignment using C#. I have a very simple console application that I'm using to test some of the code snippets provided in the manual fro the library, the goal of the assignment is to teach the program how to distinguish between random points in a square which may or may not be within a circle that is also inside the square. So basically, which points inside the square are also inside the circle. Here is what I have so far: namespace _469_A7 { class Program { static void Main(string[] args) { //Initlaize the backpropogation network LinearLayer inputLayer = new LinearLayer(2); SigmoidLayer hiddenLayer = new SigmoidLayer(8); SigmoidLayer outputLayer = new SigmoidLayer(2); new BackpropagationConnector(inputLayer, hiddenLayer); new BackpropagationConnector(hiddenLayer, outputLayer); BackpropagationNetwork network = new BackpropagationNetwork(inputLayer, outputLayer); //Generate a training set for the ANN TrainingSet trainingSet = new TrainingSet(2, 2); //TEST: Generate random set of points and add to training set, //for testing purposes start with 10 samples; Point p; Program program = new Program(); //Used to access randdouble function Random rand = new Random(); for(int i = 0; i < 10; i++) { //These points will be within the circle radius Type A if(rand.NextDouble() > 0.5) { p = new Point(rand.NextDouble(), rand.NextDouble()); trainingSet.Add(new TrainingSample(new double[2] { p.getX(), p.getY() }, new double[2] { 1, 0 })); continue; } //These points will either be on the border or outside the circle Type B p = new Point(program.randdouble(1.0, 4.0), program.randdouble(1.0, 4.0)); trainingSet.Add(new TrainingSample(new double[2] { p.getX(), p.getY() }, new double[2] { 0, 1 })); } //Start network learning network.Learn(trainingSet, 100); //Stop network learning //network.StopLearning(); } //generates a psuedo-random double between min and max public double randdouble(double min, double max) { Random rand = new Random(); if (min > max) { return rand.NextDouble() * (min - max) + max; } else { return rand.NextDouble() * (max - min) + min; } } } //Class defines a point in X/Y coordinates public class Point { private double X; private double Y; public Point(double xVal, double yVal) { this.X = xVal; this.Y = yVal; } public double getX() { return X; } public double getY() { return Y; } } } This is basically all that I need, the only question I have is how to handle output?? More specifically, I need to output the value of the "step size" and the momentum, although it would be nice to output other information as well. Anyone with experience using NeuronDotNet, your input is appreciated.

  Read the article

• Manipulating columns of numbers in elisp

  - by ~unutbu

  I have text files with tables like this: Investment advisory and related fees receivable (161,570 ) (71,739 ) (73,135 ) Net purchases of trading investments (93,261 ) (30,701 ) (11,018 ) Other receivables 61,216 (10,352 ) (69,313 ) Restricted cash 20,658 (20,658 ) - Other current assets (39,643 ) 14,752 64 Other non-current assets 71,896 (26,639 ) (26,330 ) Since these are accounting numbers, parenthesized numbers indicate negative numbers. Dashes represent 0 or no number. I'd like to be able to mark a rectangular region such as third column above, call a function (format-column), and automatically have (-73135-11018-69313+64-26330)/1000 sitting in my kill-ring. Even better would be -73.135-11.018-69.313+0.064-26.330 but I couldn't figure out a way to transform 64 -- 0.064. This is what I've come up with: (defun format-column () "format accounting numbers in a rectangular column. format-column puts the result in the kill-ring" (interactive) (let ((p (point)) (m (mark)) ) (copy-rectangle-to-register 0 (min m p) (max m p) nil) (with-temp-buffer (insert-register 0) (goto-char (point-min)) (while (search-forward "-" nil t) (replace-match "" nil t)) (goto-char (point-min)) (while (search-forward "," nil t) (replace-match "" nil t)) (goto-char (point-min)) (while (search-forward ")" nil t) (replace-match "" nil t)) (goto-char (point-min)) (while (search-forward "(" nil t) (replace-match "-" nil t) (just-one-space) (delete-backward-char 1) ) (goto-char (point-min)) (while (search-forward "\n" nil t) (replace-match " " nil t)) (goto-char (point-min)) (kill-new (mapconcat 'identity (split-string (buffer-substring (point-min) (point-max))) "+")) (kill-region (point-min) (point-max)) (insert "(") (yank 2) (goto-char (point-min)) (while (search-forward "+-" nil t) (replace-match "-" nil t)) (goto-char (point-max)) (insert ")/1000") (kill-region (point-min) (point-max)) ) ) ) (global-set-key "\C-c\C-f" 'format-column) Although it seems to work, I'm sure this function is poorly coded. The repetitive calls to goto-char, search-forward, and replace-match and the switching from buffer to string and back to buffer seems ugly and inelegant. My entire approach may be wrong-headed, but I don't know enough elisp to make this more beautiful. Do you see a better way to write format-column, and/or could you make suggestions on how to improve this code?

  Read the article

• linker error when using tr1::regex

  - by Max

  Hello. I've got a program that uses tr1::regex, and while it compiles, it gives me very verbose linker errors. Here's my header file MapObject.hpp: #include <iostream> #include <string> #include <tr1/regex> #include "phBaseObject.hpp" using std::string; namespace phObject { class MapObject: public phBaseObject { private: string color; // must be a hex string represented as "#XXXXXX" static const std::tr1::regex colorRX; // enforces the rule above public: void setColor(const string&); (...) }; } Here's my implementation: #include <iostream> #include <string> #include <tr1/regex> #include "MapObject.hpp" using namespace std; namespace phObject { const tr1::regex MapObject::colorRX("#[a-fA-F0-9]{6}"); void MapObject::setColor(const string& c) { if(tr1::regex_match(c.begin(), c.end(), colorRX)) { color = c; } else cerr << "Invalid color assignment (" << c << ")" << endl; } (...) } and now for the errors: max@max-desktop:~/Desktop/Development/CppPartyHack/PartyHack/lib$ g++ -Wall -std=c++0x MapObject.cpp /tmp/cce5gojG.o: In function std::tr1::basic_regex<char, std::tr1::regex_traits<char> >::basic_regex(char const*, unsigned int)': MapObject.cpp:(.text._ZNSt3tr111basic_regexIcNS_12regex_traitsIcEEEC1EPKcj[std::tr1::basic_regex<char, std::tr1::regex_traits<char> >::basic_regex(char const*, unsigned int)]+0x61): undefined reference tostd::tr1::basic_regex ::_M_compile()' /tmp/cce5gojG.o: In function bool std::tr1::regex_match<__gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, char, std::tr1::regex_traits<char> >(__gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, __gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, std::tr1::basic_regex<char, std::tr1::regex_traits<char> > const&, std::bitset<11u>)': MapObject.cpp:(.text._ZNSt3tr111regex_matchIN9__gnu_cxx17__normal_iteratorIPKcSsEEcNS_12regex_traitsIcEEEEbT_S8_RKNS_11basic_regexIT0_T1_EESt6bitsetILj11EE[bool std::tr1::regex_match<__gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, char, std::tr1::regex_traits<char> >(__gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, __gnu_cxx::__normal_iterator<char const*, std::basic_string<char, std::char_traits<char>, std::allocator<char> > >, std::tr1::basic_regex<char, std::tr1::regex_traits<char> > const&, std::bitset<11u>)]+0x53): undefined reference tobool std::tr1::regex_match<__gnu_cxx::__normal_iterator, std::allocator , std::allocator, std::allocator , char, std::tr1::regex_traits (__gnu_cxx::__normal_iterator, std::allocator , __gnu_cxx::__normal_iterator, std::allocator , std::tr1::match_results<__gnu_cxx::__normal_iterator, std::allocator , std::allocator, std::allocator &, std::tr1::basic_regex const&, std::bitset<11u)' collect2: ld returned 1 exit status I can't really make heads or tails of this, except for the undefined reference to std::tr1::basic_regex near the beginning. Anyone know what's going on?

  Read the article

• How to use map/reduce to handle more than 10000 unique keys for grouping in MongoDB?

  - by Magnus Johansson

  I am using MongoDB v1.4 and the mongodb-csharp driver and I try to group on a data store that has more than 10000 keys, so I get this error: assertion: group() can't handle more than 10000 unique keys using c# code like this: Document query = new Document().Append("group", new Document() .Append("key", new Document().Append("myfieldname", true)) .Append("$reduce", new CodeWScope( "function(obj,prev) { prev.count++; }")) .Append("initial", new Document().Append("count", 0)) .Append("ns", "myitems")); I read that I should use map/reduce, but I can't figure out how. Can somebody please shed some light on how to use map/reduce? Or is there any other way to get around this limitation? Thanks.

  Read the article

• Getting XQuery [modify()]: Top-level attribute nodes are not supported error while modifying xml

  - by sam

  DECLARE @mycur CURSOR DECLARE @id int DECLARE @ParentNodeName varchar(max) DECLARE @NodeName varchar(max) DECLARE @NodeText varchar(max) SET @mycur = CURSOR FOR SELECT * FROM @temp OPEN @mycur FETCH NEXT FROM @mycur INTO @id,@ParentNodeName,@NodeName,@NodeText WHILE @@FETCH_STATUS = 0 BEGIN PRINT @id -- sample statements PRINT @ParentNodeName PRINT @NodeName SET @x.modify (' insert attribute status {sql:variable("@status")} as first into (/@ParentNodeName/@NodeName/child::*[position()=sql:variable("@status")])[1] ') FETCH NEXT FROM @mycur INTO @id,@ParentNodeName,@NodeName,@NodeText END DEALLOCATE @mycur Any idea why I am getting this error as query works fine if I manually insert path

  Read the article

• Aero Snap not working for my application

  - by Magnus Österlind

  I have a problem with Aero Snap not working with the application I'm working on (Windows desktop, native C++ application), and I'm a bit confused as to what's happening, as it seems like it should just work, out of the box. I've used Spy++ on a mininal win32 application, and get the following messages when I press Win-Left: <00070 00030D1C P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:0 fUp:0 <00071 00030D1C P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:1 fUp:0 <00072 00030D1C P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:1 fUp:0 <00088 00030D1C S WM_GETMINMAXINFO lpmmi:0043FCBC <00089 00030D1C R WM_GETMINMAXINFO lpmmi:0043FCBC <00090 00030D1C S WM_WINDOWPOSCHANGING lpwp:0043FCC4 <00091 00030D1C S WM_GETMINMAXINFO lpmmi:0043F8E8 <00092 00030D1C R WM_GETMINMAXINFO lpmmi:0043F8E8 <00093 00030D1C R WM_WINDOWPOSCHANGING .. and so on So I can see that the WM_KEYDOWN for the left key isn't reaching the application, but I'm getting the aero snap "resize window" stuff instead. When I Spy++ my application, I can see that the left key isn't being "intercepted", but instead being passed on to the application, so I don't get any snapping goodness. <00043 000F0F12 P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:0 fUp:0 <00044 000F0F12 P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:1 fUp:0 <00045 000F0F12 P WM_KEYDOWN nVirtKey:VK_LWIN cRepeat:1 ScanCode:5B fRepeat:1 fUp:0 <00060 000F0F12 P WM_KEYUP nVirtKey:VK_LEFT cRepeat:1 ScanCode:4B fRepeat:0 fUp:1 I'm going to dig into the cores of our message handling and see what's going on, but I'll take all the tips I can get :)

  Read the article

• Finding the FORM that an element belongs to in JavaScript

  - by Magnus Smith

  How can I find out which FORM an HTML element is contained within, using a simple/small bit of JavaScript? In the example below, if I have already got hold of the SPAN called 'message', how can I easily get to the FORM element? <form name="whatever"> <div> <span id="message"></span> </div> </form> The SPAN might be nested within other tables or DIVs, but it seems too long-winded to iterate around .parentElement and work my way up the tree. Is there a simpler and shorter way? If it wasn't a SPAN, but an INPUT element, would that be easier? Do they have a property which points back to the containing FORM? Google says no...

  Read the article

• Help with Strings in C

  - by Anon

  Given the char * variables name1 , name2 , and name3 , write a fragment of code that assigns the largest value to the variable max (assume all three have already been declared and have been assigned values). I've tried and came up with this: if ((strcmp(name1,name2)0)&&(strcmp(name1,name3)0)){ max=name1; } else if ((strcmp(name2,name1)0)&&(strcmp(name2,name3)0)){ max=name2; } else if ((strcmp(name3,name1)0)&&(strcmp(name3,name2)0)){ max=name3; } However, I get this error Your code is incorrect. You are not handling the situation                where two or more strings are equal.

  Read the article

• Getting website data into Adobe InDesign

  - by Magnus Smith

  I'd like our magazine team to be able to download website data in a file that Adobe InDesign can read. They can then import/open the file, make a few tweaks, and cut out a vast deal of repetitive manual labour (they currently use copy&paste for a few hours). After a brief Google I note that v2 of InDesign can import/export XML so perhaps that is my best bet? Are there any alternatives, and can anyone offer any advice on them? I am using a PC, and the magazine team are on Macs; testing will be tiresome I fear. The data we wish to format is fairly simple - a title followed by a short chunk of text (repeated about 50 times, say). I'll ask about importing images later. Thanks for your help. I will return to Google now, but it would be great if anyone can point me in a more specific direction first!

  Read the article

• Table alias has an effect with execution time?

  - by RedFux227

  So I have this query : SELECT A.e_cd "INFLATE" , A.ccgpt "1" , ( SELECT J.comp FROM JBB J WHERE J.e_cd=A.e_cd AND emplo_RCD=:1 AND J.Dte = ( SELECT MAX(J1.Dte) FROM JBB J1 WHERE J.e_cd=J1.e_cd AND TO_CHAR(J1.Dte,'MM') <=A.mth_to AND TO_CHAR(J1.Dte,'YYYY') <=A.year ) AND J.seq = ( SELECT MAX(J2.seq) FROM PS_JOB J2 WHERE J2.e_cd=J.e_cd AND J2.Dte=J.Dte)) "Company" FROM PPS A WHERE orcd=:2 AND rcd=:3 AND tx_cd=:4 AND year=:5 With this one : SELECT A.e_cd "INFLATE" , A.ccgpt "1" , ( SELECT J.comp FROM JBB J WHERE J.e_cd=A.e_cd AND emplo_RCD=:1 AND J.Dte = ( SELECT MAX(J1.Dte) FROM JBB J1 WHERE J.e_cd=J1.e_cd AND TO_CHAR(J1.Dte,'MM') <=A.mth_to AND TO_CHAR(J1.Dte,'YYYY') <=A.year ) AND J.seq = ( SELECT MAX(J1.seq) **FROM PS_JOB J1 WHERE J1.e_cd=J.e_cd AND J1.Dte=J.Dte**)) "Company" FROM PPS A WHERE orcd=:2 AND rcd=:3 AND tx_cd=:4 AND year=:5 The 1st query run for about 3.20 sec with buffer gets 8,134 and for the 2nd query it run for about 1.73 sec with buffer gets 7,006. So, is the table alias somehow has an impact on the execution time / buffer gets? Thanks in advance!

  Read the article

• Compiling C lib and OCaml exe using it, all using ocamlfind

  - by Magnus

  I'm trying to work out how to use ocamlfind to compile a C library and an OCaml executable using that C library. I put together a set of rather silly example files. % cat sillystubs.c #include <stdio.h> #include <caml/mlvalues.h> #include <caml/memory.h> #include <caml/alloc.h> #include <caml/custom.h> value caml_silly_silly( value unit ) { CAMLparam1( unit ); printf( "%s\n", __FILE__ ); CAMLreturn( Val_unit ); } % cat silly.mli external silly : unit -> unit = "silly_silly" % cat foo.ml open Silly open String let _ = print_string "About to call into silly"; silly (); print_string "Called into silly" I believe the following is the way to compile up the library: % ocamlfind ocamlc -c sillystubs.c % ar rc libsillystubs.a sillystubs.o % ocamlfind ocamlc -c silly.mli % ocamlfind ocmalc -a -o silly.cma -ccopt -L${PWD} -cclib -lsillystubs Now I don't seem to be able to use the created library though: % ocamlfind ocamlc -custom -o foo foo.cmo silly.cma /usr/bin/ld: cannot find -lsillystubs collect2: ld returned 1 exit status File "_none_", line 1, characters 0-1: Error: Error while building custom runtime system The OCaml tools are somewhat mysterious to me, so any pointers would be most welcome.

  Read the article

• Can I spead out a long running stored proc accross multiple CPU's?

  - by Russ

  [Also on SuperUser - http://superuser.com/questions/116600/can-i-spead-out-a-long-running-stored-proc-accross-multiple-cpus] I have a stored procedure in SQL server the gets, and decrypts a block of data. ( Credit cards in this case. ) Most of the time, the performance is tolerable, but there are a couple customers where the process is painfully slow, taking literally 1 minute to complete. ( Well, 59377ms to return from SQL Server to be exact, but it can vary by a few hundred ms based on load ) When I watch the process, I see that SQL is only using a single proc to perform the whole process, and typically only proc 0. Is there a way I can change my stored proc so that SQL can multi-thread the process? Is it even feasible to cheat and to break the calls in half, ( top 50%, bottom 50% ), and spread the load, as a gross hack? ( just spit-balling here ) My stored proc: USE [Commerce] GO /****** Object: StoredProcedure [dbo].[GetAllCreditCardsByCustomerId] Script Date: 03/05/2010 11:50:14 ******/ SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO ALTER PROCEDURE [dbo].[GetAllCreditCardsByCustomerId] @companyId UNIQUEIDENTIFIER, @DecryptionKey NVARCHAR (MAX) AS SET NoCount ON DECLARE @cardId uniqueidentifier DECLARE @tmpdecryptedCardData VarChar(MAX); DECLARE @decryptedCardData VarChar(MAX); DECLARE @tmpTable as Table ( CardId uniqueidentifier, DecryptedCard NVarChar(Max) ) DECLARE creditCards CURSOR FAST_FORWARD READ_ONLY FOR Select cardId from CreditCards where companyId = @companyId and Active=1 order by addedBy desc --2 OPEN creditCards --3 FETCH creditCards INTO @cardId -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN --OPEN creditCards DECLARE creditCardData CURSOR FAST_FORWARD READ_ONLY FOR select convert(nvarchar(max), DecryptByCert(Cert_Id('Oh-Nay-Nay'), EncryptedCard, @DecryptionKey)) FROM CreditCardData where cardid = @cardId order by valueOrder OPEN creditCardData FETCH creditCardData INTO @tmpdecryptedCardData -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN print 'CreditCardData' print @tmpdecryptedCardData set @decryptedCardData = ISNULL(@decryptedCardData, '') + @tmpdecryptedCardData print '@decryptedCardData' print @decryptedCardData; FETCH NEXT FROM creditCardData INTO @tmpdecryptedCardData -- fetch next END CLOSE creditCardData DEALLOCATE creditCardData insert into @tmpTable (CardId, DecryptedCard) values ( @cardId, @decryptedCardData ) set @decryptedCardData = '' FETCH NEXT FROM creditCards INTO @cardId -- fetch next END select CardId, DecryptedCard FROM @tmpTable CLOSE creditCards DEALLOCATE creditCards

  Read the article

• Can I spread out a long running stored proc accross multiple CPU's?

  - by Russ

  [Also on SuperUser - http://superuser.com/questions/116600/can-i-spead-out-a-long-running-stored-proc-accross-multiple-cpus] I have a stored procedure in SQL server the gets, and decrypts a block of data. ( Credit cards in this case. ) Most of the time, the performance is tolerable, but there are a couple customers where the process is painfully slow, taking literally 1 minute to complete. ( Well, 59377ms to return from SQL Server to be exact, but it can vary by a few hundred ms based on load ) When I watch the process, I see that SQL is only using a single proc to perform the whole process, and typically only proc 0. Is there a way I can change my stored proc so that SQL can multi-thread the process? Is it even feasible to cheat and to break the calls in half, ( top 50%, bottom 50% ), and spread the load, as a gross hack? ( just spit-balling here ) My stored proc: USE [Commerce] GO /****** Object: StoredProcedure [dbo].[GetAllCreditCardsByCustomerId] Script Date: 03/05/2010 11:50:14 ******/ SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO ALTER PROCEDURE [dbo].[GetAllCreditCardsByCustomerId] @companyId UNIQUEIDENTIFIER, @DecryptionKey NVARCHAR (MAX) AS SET NoCount ON DECLARE @cardId uniqueidentifier DECLARE @tmpdecryptedCardData VarChar(MAX); DECLARE @decryptedCardData VarChar(MAX); DECLARE @tmpTable as Table ( CardId uniqueidentifier, DecryptedCard NVarChar(Max) ) DECLARE creditCards CURSOR FAST_FORWARD READ_ONLY FOR Select cardId from CreditCards where companyId = @companyId and Active=1 order by addedBy desc --2 OPEN creditCards --3 FETCH creditCards INTO @cardId -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN --OPEN creditCards DECLARE creditCardData CURSOR FAST_FORWARD READ_ONLY FOR select convert(nvarchar(max), DecryptByCert(Cert_Id('Oh-Nay-Nay'), EncryptedCard, @DecryptionKey)) FROM CreditCardData where cardid = @cardId order by valueOrder OPEN creditCardData FETCH creditCardData INTO @tmpdecryptedCardData -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN print 'CreditCardData' print @tmpdecryptedCardData set @decryptedCardData = ISNULL(@decryptedCardData, '') + @tmpdecryptedCardData print '@decryptedCardData' print @decryptedCardData; FETCH NEXT FROM creditCardData INTO @tmpdecryptedCardData -- fetch next END CLOSE creditCardData DEALLOCATE creditCardData insert into @tmpTable (CardId, DecryptedCard) values ( @cardId, @decryptedCardData ) set @decryptedCardData = '' FETCH NEXT FROM creditCards INTO @cardId -- fetch next END select CardId, DecryptedCard FROM @tmpTable CLOSE creditCards DEALLOCATE creditCards

  Read the article

• Can I spread out a long running stored proc accross multiple CPU's?

  - by Russ

  [Also on SuperUser - http://superuser.com/questions/116600/can-i-spead-out-a-long-running-stored-proc-accross-multiple-cpus] I have a stored procedure in SQL server the gets, and decrypts a block of data. ( Credit cards in this case. ) Most of the time, the performance is tolerable, but there are a couple customers where the process is painfully slow, taking literally 1 minute to complete. ( Well, 59377ms to return from SQL Server to be exact, but it can vary by a few hundred ms based on load ) When I watch the process, I see that SQL is only using a single proc to perform the whole process, and typically only proc 0. Is there a way I can change my stored proc so that SQL can multi-thread the process? Is it even feasible to cheat and to break the calls in half, ( top 50%, bottom 50% ), and spread the load, as a gross hack? ( just spit-balling here ) My stored proc: USE [Commerce] GO /****** Object: StoredProcedure [dbo].[GetAllCreditCardsByCustomerId] Script Date: 03/05/2010 11:50:14 ******/ SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO ALTER PROCEDURE [dbo].[GetAllCreditCardsByCustomerId] @companyId UNIQUEIDENTIFIER, @DecryptionKey NVARCHAR (MAX) AS SET NoCount ON DECLARE @cardId uniqueidentifier DECLARE @tmpdecryptedCardData VarChar(MAX); DECLARE @decryptedCardData VarChar(MAX); DECLARE @tmpTable as Table ( CardId uniqueidentifier, DecryptedCard NVarChar(Max) ) DECLARE creditCards CURSOR FAST_FORWARD READ_ONLY FOR Select cardId from CreditCards where companyId = @companyId and Active=1 order by addedBy desc --2 OPEN creditCards --3 FETCH creditCards INTO @cardId -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN --OPEN creditCards DECLARE creditCardData CURSOR FAST_FORWARD READ_ONLY FOR select convert(nvarchar(max), DecryptByCert(Cert_Id('Oh-Nay-Nay'), EncryptedCard, @DecryptionKey)) FROM CreditCardData where cardid = @cardId order by valueOrder OPEN creditCardData FETCH creditCardData INTO @tmpdecryptedCardData -- prime the cursor WHILE @@Fetch_Status = 0 BEGIN print 'CreditCardData' print @tmpdecryptedCardData set @decryptedCardData = ISNULL(@decryptedCardData, '') + @tmpdecryptedCardData print '@decryptedCardData' print @decryptedCardData; FETCH NEXT FROM creditCardData INTO @tmpdecryptedCardData -- fetch next END CLOSE creditCardData DEALLOCATE creditCardData insert into @tmpTable (CardId, DecryptedCard) values ( @cardId, @decryptedCardData ) set @decryptedCardData = '' FETCH NEXT FROM creditCards INTO @cardId -- fetch next END select CardId, DecryptedCard FROM @tmpTable CLOSE creditCards DEALLOCATE creditCards

  Read the article

• Split large text string into variable length strings without breaking words and keeping linebreaks a

  - by Frank

  I am trying to break a large string of text into several smaller strings of text and define each smaller text strings max length to be different. for example: "The quick brown fox jumped over the red fence. The blue dog dug under the fence." I would like to have code that can split this into smaller lines and have the first line have a max of 5 characters, the second line have a max of 11, and rest have a max of 20, resulting in this: Line 1: The Line 2: quick brown Line 3: fox jumped over the Line 4: red fence. Line 5: The blue dog Line 6: dug under the fence. All this in C# or MSSQL, is it possible?

  Read the article

• How to prevent application thievery (specific to Android applications)?

  - by Berdon Magnus

  Hey, I was wondering what the most effective way of preventing people from stealing my application (downloading a copy of the .apk online rather than buying it). I've spent a lot of time on one in particular (Droidbox) and won't be releasing Sync until I can guarantee that the people who are providing illegal copies of the pro version aren't able to. Anyone implemented this? I've tried checking my package signature verses an the signature of an unsigned copy but it appears to be the same - perhaps I'm doing something incorrectly here. I'm unsure whether people actually distribute the signed .apk in which case I don't think signature validation would work to begin with... Please note, this question is specific to Android Marketplace Applications - the difference being, application delivery is out of my hands and I have no way of linking between a legitimate purchase and an illegal download.

  Read the article

• Converting SQL statement into Linq

  - by DMan

  I'm trying to convert the following to a LINQ to SQL statement in C#. Can anyone give me a hand? Basically my table keeps record of all history of changes such that the created date max date for each seedlot is the most recent record and the correct one to show. SELECT reports.* FROM [dbo].[Reports] reports WHERE reports.createdDate IN ( SELECT MAX(report_max_dates.createdDate) FROM [dbo].[Reports] report_max_dates GROUP BY report_max_dates.Lot ) So far this is what I have. var result = (from report in db.Reports where report.createdDate == (from report_max in db.Reports group report_max by report_max.Lot into report_max_grouped select report_max_grouped).Max() select report); I can't figure out how to get the MAX dates for all reports and how to do an IN statement on the report.createdDate. Thansk, Dman

  Read the article

• MS Sql Get Top xx Blog Record From Umbraco by parameter...

  - by ccppjava

  Following SQL get what I need: SELECT TOP (50) [nodeId] FROM [dbo].[cmsContentXml] WHERE [xml] like '%creatorID="29"%' AND [xml] like '%nodeType="1086"%' ORDER BY [nodeId] DESC I need to pass in the numbers as parameters, so I have follows: exec sp_executesql N'SELECT TOP (@max) [nodeId] FROM [dbo].[cmsContentXml] WHERE [xml] like ''%creatorID="@creatorID"%'' AND [xml] like ''%nodeType="@nodeType"%'' ORDER BY [nodeId] DESC',N'@max int,@creatorID int,@nodeType int',@max=50,@creatorID=29,@nodeType=1086 which however, returns no record, any idea?

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >