Search Results

Search found 13218 results on 529 pages for 'live usb'.

Page 311/529 | < Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess. (Edit - One extra thing that may or may not be relevant: it's the 64 bit version of Server 2008 R2)

  Read the article

• Logitech MK300 : "no driver found"

  - by Oystein

  Hi I bought kewyboard and mouse from Logitech. The model is MK300. I wanna run 64-bits Windows 7 with this. When I connect the USB-receiver, Windows is trying to install it but gives me the error message: "no driver found". I tried to download SetPoint 4.80, but that didn't help. I have rebooted the computer several of times, tried different USB'ports, and have allso tried menye different mouses from Logitech. Non of this works. Have someone any suggestions for how I can fix my problem?

  Read the article

• Windows lowers volume because of "communication"

  - by SnippetSpace

  Randomly, or at system sound (usb connect for example) Windows 8 lowers the volume of all other sources. (Same problem can exist on windows 7, just look online). This is happening because of the "communication detection" made to detect phone calls and then lower volume. But in my case it happens all the time without reason as if windows always considers myself in a call. Do any of you have the same problem? is this a driver issue or a windows issue? I know this has been posted many times but they usually just tell you to turn off the setting above. I'm looking for an explanation or a solution :). Thanks for your feedback and ideas.

  Read the article

• What is this jumper for on my new motherboard?

  - by jasondavis

  I am building a new PC, I just got my motherboard in the mail today. It is a ASRock X58 Extreme 3. I am reading over the manual for it and one of the jumpers says this. There is a 3 pin jumper labeled 1 2 3, with pins 1 and 2 shorted by default it is "+5v" If I manually change it to short jumper pins 2 and 3 instead of 1 and 2 then it will be "+5vSB (standby) for PS/2 or USB wake up events. So I am confused as to exactly what this is for. Can someone explain what it means, why I would want one other the other?

  Read the article

• Best way to fix security problems caused by windows updates?

  - by Chris Lively

  I have a laptop running Windows 7 32-bit. Last nights security updates caused my logitech mouse to stop working (specifically, it caused several USB ports to stop altogether). After reviewing the system event log I found that the IPBusEnum component was failing due to an activation security error. A little more research and I found that this was caused by the TrustedInstaller replacing the security permissions on those keys and generally mucking them up. To fix this I had to open regedit, take ownership of ALL the keys related to IPBusEnum and force it to use the inherited permissions from the tree. Is there a better way to fix this when MS screws up the updates? I would hate to have to walk around to a number of machines and manually fix the registry key security settings.

  Read the article

• Robocopy to a drive connected to a wlan router fails

  - by Ville Koskinen

  I have a wireless router and an USB hard drive connected to it. Basic file access on the command line and Explorer works flawlessly after having set up some options on the router and mapping to some folders with net use k: \\ROUTER\Folder1 /user:MYLAPTOP\Me password /persistent:yes net use n: \\ROUTER\Folder2 /user:MYLAPTOP\Me password /persistent:yes Robocopy (and using SyncToy for that matter) to a network drive however fails: robocopy c:\Files k:\Backup /MIR /Z gives There is not enough space on the disk. 2010/01/05 09:52:11 ERROR 112 (0x00000070) Accessing Destination Directory N:\ Waiting 30 seconds... The error message is misleading: there is plenty of space on the disk and the folders I'm copying are small. The router is an ASUS WL-500gp with a standard firmware. I'd appreciate if someone would be able to explain what is causing the problem and, if possible, how to fix it.

  Read the article

• Why did my Cisco router hang?

  - by Mike Pennington

  We have a Cisco 1841 in our storage IDF that was originally running a 12.4(1) IP-BASE image; I wanted to upgrade to an advancedservicesk9-mz image, but the flash did not have enough space, so I deleted the running image. Later I tried inserting a larger CF from a Catalyst4500, which crashed the 1841 router (now without a bootable image). Using another 1800 series router, I loaded the 12.4(25g) advancedservicesk9 image and verified the image checksums. I set the confreg to 0x2102 from rommon and booted the new image; however the 1841 now hangs indefinitely after printing the IOS export control banner. I have tried four other images, all with the same results. What is wrong with this router? UPDATE 1: I tried loading images from a FAT16-formatted USB, but this didn't work either. I also tried tftpdnld from rommon, but got a get_mac_address(): Search T_IDPROM_MACADDR (0xc3) failed Illegal MAC address. error and the file would not load.

  Read the article

• What's the best way to debug URLRewrite rules?

  - by Charlie

  Trying to do a few URLRewrite rules - some of them worked, some didn't. For those that didn't work, how do you debug it? Especially if the rule was never invoked, how do I tell where I'm making a mistake? Tried Live HTTP Header extension with firefox as well as checking the server access logs, to no avail. My site is hosted with cpanel, using apache, and the rewrite rules are defined in .htaccess (I have some rules that worked, so it's not a setup issue I'm pretty sure) Thanks

  Read the article

• Is Google Maps API V3 good enough to use now?

  - by Haroldo

  Firstly, only reply if you have experience using API V3 (i can speculate myself!) I had a little go with V3 and it looked great but would love to hear from someone who's given it a bit of use before I start working with it and deploy it on a live site. I'm only looking to do very basic things: put markers on a map custom markers info bubbles It all looks very easy with v3: http://www.svennerberg.com/2009/06/google-maps-api-3-the-basics/ is it stable enough?

  Read the article

• eSATA hotswap using Jmicron JMB363 controller

  - by Stephen

  I have tried both IDE and AHCI modes in the BIOS. Also tried many different driver revisions. I can't seem to hot swap an external SATA drive. I can use the wizard to safely remove it, but reconnecting doesn't do anything unless I reboot. I use a thermaltake dock, and I would like to swap in my backup drive sometimes to do images (they take all day over USB). I can reboot, but I'd like to use hot swap. The controller is a Jmicron JMB363. I'm using the latest BIOS on my motherboard, as well.

  Read the article

• Using ethernet cables?

  - by Farhad Yusufali

  I have an HDTV which supports internet connectivity through an ethernet port or wirelessly (but this requires an additional wireless USB adapter, which I don't have). I also have a blue ray player than supports internet connectivity through an ethernet port or wirelessly (natively - no other devices are needed). I want to connect my TV to the internet but my router is too far away. My blueray player however is already connected wirelessly. If I connected my TV to my Blueray player via ethernet, would my TV be able to connect to the internet? To clarify: Wireless Signal - Blue Ray Player - Ethernet Cable - TV Would this work?

  Read the article

• Windows 2008 and Truecrypt: can't access shared folder called "media"

  - by Sajee

  On my Windows 2008 system, I've attached an external USB drive that's encrypted using Truecrypt. Once I mounted the Truecrypt drive, I share some of the directories from that drive using Windows file sharing. I tried sharing a folder called "media" and when I try to access that folder from a Vista client on my LAN via \myserver\media, I get this error: \myserver\media is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. An unexpected network error occurred. If I share the folder media under some name such as fizzbuzz then I can access \myserver\fizzbuzz w/o any errors. Any clues as to why this is happening? Related: http://serverfault.com/questions/27684/windows-2008-and-truecrypt-how-to-automatically-mount-shared-folders-after-rest

  Read the article

• Protect .net Web Service URL

  - by Nirmal

  Hello All... I have created Web Service using Asp.net 3.5. Now it's working perfectly in live windows server, and giving me perfect xml while invoking it using some url like : http://www.somedomain.com/Service.asmx?op=fetchData Now My question is when I am accessing url like : http://www.somedomain.com/Service.asmx it's listing my created web services. What if I don't wanna list down the available web services to end users. Thanks in advance...

  Read the article

• Damaged XenServer Storage LVM partition table

  - by Fiolek

  I have a homeserver running under XenServer control with 3x1TB discs inside, one for XenServer and two mirrored(using Intel's fakeRAID and dmraid) for VMs and a user data(but now I think RAID didn't work). I tried to pass PCI card to VM using PCI-passthroug and I read somewhere that I need to recompile kernel with pciback module but something went wrong(I made mistake in /boot/extlinux.conf and server couldn't run) and I had to use LiveCD of GPartEd(I already had it on USB key) to correct this. But when I re-run the server all VDIs were gone. I have completly no idea what could go wrong. I tried to repair RAID using dmraid -R in the hope that everything will return to noramal but now I think this done more bad than good(and corrupted rest of LVM table...). Is there any possibility to recover this SR or only data from one(~100GB) of VDI? I also wants to apologise for my English, I'm not from English-speaking country and I'm only 16 years old, so I hadn't "time" to learn it(school isn't good place to do this) in sufficient way.

  Read the article

• PC reboots automatically in the begining

  - by user233508

  I have a AMD Phenom II 3GHz. 2 GB RAM system running on Windows 7. Off late my PC does not start properly I have to start it at least 7-8 times before it starts. It starts and then shuts down. Every time the time for which the system is up increases. After 7-8 attempts it starts an works fine. I have to give it a min between restarts (USB mouse light goes off). If I try restarting before this time the PC does not start. I am suspecting humidity playing some factor as this issue has started creeping up ever since the rains have started.

  Read the article

• get mail, Fire Job, Asp.Net, C#.Net

  - by AjmeraInfo

  I live in India and My hosting server at US. I am using MSSQL, ASP.Net and C#.Net I want to fire job when i will get email. ex. someone send mail on my address. then i want to get sms for email description. it not possible to install any desktop or console application on US hosting server. I don't have that type of rights.

  Read the article

• How to make multiple Popups using Jquery

  - by Rajasekar

  For pop up im using the following code style : a.selected { background-color:#1F75CC; color:white; z-index:100; } .messagepop { background-color:#FFFFFF; border:1px solid #999999; cursor:default; display:none; margin-top: 15px; position:absolute; text-align:left; width:394px; z-index:50; padding: 25px 25px 20px; } label { display: block; margin-bottom: 3px; padding-left: 15px; text-indent: -15px; } .messagepop p, .messagepop.div { border-bottom: 1px solid #EFEFEF; margin: 8px 0; padding-bottom: 8px; } JavaScript : $(function() { $("#contact").live('click', function(event) { $(this).addClass("selected").parent().append('<div class="messagepop pop"><form method="post" id="new_message" action="/messages"><p><label for="email">Your email or name</label><input type="text" size="30" name="email" id="email" /></p><p><label for="body">Message</label><textarea rows="6" name="body" id="body" cols="35"></textarea></p><p><input type="submit" value="Send Message" name="commit" id="message_submit"/> or <a class="close" href="/">Cancel</a></p></form></div>'); $(".pop").slideFadeToggle() $("#email").focus(); return false; }); $(".close").live('click', function() { $(".pop").slideFadeToggle(); $("#contact").removeClass("selected"); return false; }); }); $.fn.slideFadeToggle = function(easing, callback) { return this.animate({ opacity: 'toggle', height: 'toggle' }, "fast", easing, callback); }; and finally <a href="/contact" id="contact">Contact Us</a> I need to include another pop up when the register link is clicked. Whether i should use the same function with modifications or seperate functions. Please provide me the code with modifications. Im so weird. Help me.

  Read the article

• Dual booting windows 8.1 and ubuntu

  - by Sriniketh

  I have a lenovo laptop with windows 8.1. I wanted to use ubuntu alongside windows. Hence, i downloaded the ubuntu 14.04 iso and created a live pendrive using Universal USB installer. I disabled secure boot and booted from the pendrive. All i get is the GNU GRUB command line version 2.X. I don't get a GUI for the GRUB and i don't know how to boot into ubuntu from the command line. I searched quite a few online forums but in vain. Can someone tell me how to proceed? Thanks in advance.

  Read the article

• Keyboard automatically disconnects and reconnects

  - by Algorithms

  The problem i am facing is the keyboard (USB) automatically disconnects when there is a fluctuation in the power supply to the speaker. The speaker and the pc both draw power from a apc ups. The fluctuation occurs because the speaker plug is not tightly connected to the ups power outlet. It is okay for normal work, but a accidental jerk causes the fluctuation. However after some amount of time (usually within 5 seconds) the keyboard automatically reconnects and windows plays the sound of hardware connected. This problem will also occur if I manually take out the speaker power cable from the ups power outlet. My question is whether the problem I am facing is due to electrical issues, or due to software problems. PC config: OS : Windows 7 Ultimate UPS : APC 600 VA PSU : Corsair TX 650 Speaker : Realtek

  Read the article

• Wildcards not being substituted

  - by user21463

  #!/bin/bash loc=`echo ~/.gvfs/*/DCIM/100_FUJI` rm -f /mnt/fujifilmA100 ln -s "$loc" /mnt/fujifilmA100 For some reason the variable * doesn't get substituted with the only possible value and gets given the value /home/chris/.gvfs/*/DCIM/100_FUJI. Does anyone have an idea of why? Please note: If global expansion fails, the pattern is not substituted. I ran the commands: chris@comp2008:~$ loc=`echo ~/.gvfs/*/DCIM/100_FUJI ` chris@comp2008:~$ echo $loc /home/chris/.gvfs/gphoto2 mount on usb%3A001,008/DCIM/100_FUJI So we can see the expansion should work I have now switched to using: loc = `find ~/.gvfs -name 100_FUJI ` I am just curious why it doesn't work as is. Debugging output using sh -x echo /home/chris/.gvfs/*/DCIM/100_FUJI loc=/home/chris/.gvfs/*/DCIM/100_FUJI rm -f /mnt/fujifilmA100 ln -s /home/chris/.gvfs/*/DCIM/100_FUJI/mnt/fujifilmA100

  Read the article

• win xp client, win 7 host, only xp drivers

  - by brett

  I have a win 7 64 bit box which has xp on it in a vmware module and also the win7 version. I can use my old usb wifi card under virtual xp as i have the wifi drivers, but apparently the manufacturing company never made any further drivers, nor did it release the source code. Is it possible to get networking between the client and the host, so that my host can browse etc? I thought the microsoft loopback adapter might be the answer but ever example i can find of it's use describes a setup where the host is connected fine and needs to route data to the client as well.

  Read the article

• Optional non-system type parameters

  - by Courtney de Lautour

  C#4.0 obviously brings optional parameters (which I've been waiting for, for quite some time). However it seems that because only system types can be const that I cannot use any class/struct which I have created, as an optional param. Is there a some way which allows me to use a more complex type as an optional parameter. Or is this one of the realities that one must just live with?

  Read the article

• Google Maps API v3: InfoWindow not sizing correctly

  - by JacobT

  Hi all It appears my InfoWindow, when you click on the home icon on my Google Maps v3, is not properly auto-sizing to the content of the InfoWindow. It gives scrollbars when it should not. The InfoWindow should be properly auto-sizing. Any ideas on why? Link below to live size. http://tinyurl.com/ygktsj Per request, the relevant JavaScript which injects the HTML for the InfoWindow: listing = '<div>Content goes here</div>';

  Read the article

• How can you connect three external displays to a laptop with only one vga or dvi port and plenty of

  - by Byron

  I have had some success with usb docks like this Universal Docking Station by Kensington to connect one external display to my laptop while using the onboard vga port for another display. But that's only two displays and I'm shooting for three. All I do is develop software and work in Photoshop... no games. For the sake of discussion, we can assume a Thinkpad or equivalent laptop with Windows 7 (I'm hoping for a platform-agnostic solution). How could I do this?

  Read the article

• Where do SATA drives get their power when using a PCI SATA controller on oler PCs?

  - by Sukima

  I've been looking into PCI SATA controller cards online for an older PC and noticed that the ports only have the SATA cable connector and the Power supply does not have the SATA power connectors. I also had a few external eSATA drives which don't power up unless I also plugin the USB cable. Therefore I realize that SATA and eSATA do not carry power and need power else where. When converting older PCs to use a PCI SATA controller how do you provide power to the SATA drives? Anticipating the answer to be some kind of converter cable (which I was unable to search for) then can older power supplies handle added drives? (Assuming a 4 port SATA controller means 4 more drives the power supply has to endure). Or do you have to get a second poer supply and kinda jerry-rig it into an old case?

  Read the article

< Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >