Search Results

Search found 8349 results on 334 pages for 'entity groups'.

Page 313/334 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

• Recover RAID 5 data after created new array instead of re-using

  - by Brigadieren

  Folks please help - I am a newb with a major headache at hand (perfect storm situation). I have a 3 1tb hdd on my ubuntu 11.04 configured as software raid 5. The data had been copied weekly onto another separate off the computer hard drive until that completely failed and was thrown away. A few days back we had a power outage and after rebooting my box wouldn't mount the raid. In my infinite wisdom I entered mdadm --create -f... command instead of mdadm --assemble and didn't notice the travesty that I had done until after. It started the array degraded and proceeded with building and syncing it which took ~10 hours. After I was back I saw that that the array is successfully up and running but the raid is not I mean the individual drives are partitioned (partition type f8 ) but the md0 device is not. Realizing in horror what I have done I am trying to find some solutions. I just pray that --create didn't overwrite entire content of the hard driver. Could someone PLEASE help me out with this - the data that's on the drive is very important and unique ~10 years of photos, docs, etc. Is it possible that by specifying the participating hard drives in wrong order can make mdadm overwrite them? when I do mdadm --examine --scan I get something like ARRAY /dev/md/0 metadata=1.2 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b name=<hostname>:0 Interestingly enough name used to be 'raid' and not the host hame with :0 appended. Here is the 'sanitized' config entries: DEVICE /dev/sdf1 /dev/sde1 /dev/sdd1 CREATE owner=root group=disk mode=0660 auto=yes HOMEHOST <system> MAILADDR root ARRAY /dev/md0 metadata=1.2 name=tanserv:0 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b Here is the output from mdstat cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[0] sdf1[3] sde1[1] 1953517568 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/3] [UUU] unused devices: <none> fdisk shows the following: fdisk -l Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bf62e Device Boot Start End Blocks Id System /dev/sda1 * 1 9443 75846656 83 Linux /dev/sda2 9443 9730 2301953 5 Extended /dev/sda5 9443 9730 2301952 82 Linux swap / Solaris Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de8dd Device Boot Start End Blocks Id System /dev/sdb1 1 91201 732572001 8e Linux LVM Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00056a17 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 8e Linux LVM Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ca948 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/dm-0: 1250.3 GB, 1250254913536 bytes 255 heads, 63 sectors/track, 152001 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93a66687 Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6edc059 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/md0: 2000.4 GB, 2000401989632 bytes 2 heads, 4 sectors/track, 488379392 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1048576 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Per suggestions I did clean up the superblocks and re-created the array with --assume-clean option but with no luck at all. Is there any tool that will help me to revive at least some of the data? Can someone tell me what and how the mdadm --create does when syncs to destroy the data so I can write a tool to un-do whatever was done? After the re-creating of the raid I run fsck.ext4 /dev/md0 and here is the output root@tanserv:/etc/mdadm# fsck.ext4 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Superblock invalid, trying backup blocks... fsck.ext4: Bad magic number in super-block while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 Per Shanes' suggestion I tried root@tanserv:/home/mushegh# mkfs.ext4 -n /dev/md0 mke2fs 1.41.14 (22-Dec-2010) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=128 blocks, Stripe width=256 blocks 122101760 inodes, 488379392 blocks 24418969 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 14905 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 and run fsck.ext4 with every backup block but all returned the following: root@tanserv:/home/mushegh# fsck.ext4 -b 214990848 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Invalid argument while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> Any suggestions? Regards!

  Read the article

• Remote Desktop Services Gateway Issue

  - by AVandelay05

  Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

  Read the article

• Error during GENERAL_REQUEST_ENTITY for POST results in ASP .NET session state never getting unlocked

  - by Jesse

  I have been trying to chase down the root cause of a condition where ASP .NET session state remains locked after a web request has been terminated due to an unexpected error. We use the SQL Server session state provider for session because we have several servers in a web farm. This issue first presented itself in the form of many requests getting stuck on the 'AcquireRequestState' event of their lifecycle for no apparent reason. I was able to finding corresponding entries for these requests in the session state database in SQL server that were all locked (column Locked = 1). I was also able to correlate these requests to entries in the IIS log with HTTP status codes of 500 (with a sub status of 0). These findings lead me to believe that, in some cases, a request was erroring out but was NOT releasing its lock on session state like it should. I enabled Failed Request Tracing in IIS for the website in question for status code 500 with all available providers selected each with the 'Verbose' setting for verbosity. I've since gathered several failed traces that have caused permanently locked ASP .NET sessions. They all share the same characteristics: They are all 'POST' requests where the browser is posting data to be processed/saved. They all have events indicating that the 'Session' module was invoked during the REQUEST_ACQUIRE_STATE event. At this point the request would have marked the row in the session state database as being "locked". This is normal and expected. They all have GENERAL_READ_ENTITY_START, GENERAL_READ_ENTITY_END, and GENERAL_REQUEST_ENTITY entries that appear to be reading in the data that was posted to the server as part of the request. This appears to be a buffered operation as these events get repeated over and over with each one reading in some subset of the posted data. At some point during the 'read entity' related events and error occurs. Some have the error code "Incorrect function. (0x80070001)" and others have "The I/O operation has been aborted because of either a thread exit or an application request. (0x800703e3)". Once the error has been encountered, they all jump directly to the END_REQUEST events. The issue here is that, under normal circumstances, there should be a RELEASE_REQUEST_STATE event that will allow the Session module to release the lock it has on the session. This event is being skipped in this scenario. Just to be sure, I enabled failed request tracing for the '200' status code as well and generated several traces of successful requests that do have the RELEASE_REQUEST_STATE event being handled by the Session module. My theory at this point is that some kind of network issue is causing the 'Incorrect function' and 'I/O operation has been aborted because of either a thread exit or an application request' errors, but I don't understand why this seems to be causing the request handling to skip over the RELEASE_REQUEST_STATE event. If the request went through REQUEST_ACQUIRE_STATE it seems like it should also hit RELEASE_REQUEST_STATE as well. I'm loathe to say that this is a bug in IIS or ASP .NET, but it certainly appears that way to me at this point. Are there any configuration changes I could make to help ensure that 'RELEASE_REQUEST_STATE' is fired under all error conditions?

  Read the article

• Windows 7 cannot join samba domain

  - by Antonis Christofides

  I have a 3.5.6 samba server with a LDAP backend (both on Debian 6.0). I've been successfully adding Windows XP machines to the domain for years. I now try to add Windows 7. I have made the recommended registry changes, but I don't have any success so far. Here is what happens: 1. I go to computer name, select "Domain" instead of "Workgroup", type in the domain name, click OK. It asks me for the username and password of an account that can add computers to the domain; I enter them. After about 40 seconds, I get the following message: The following error occurred attempting to join the domain "ITIA": The specified computer account could not be found. Contact an administrator to verify the account is in the domain. If the account has been deleted unjoin, reboot, and rejoin the domain. Despite this, the samba server successfully creates the computer account. 2. Therefore, if I try again a second time, without deleting the already created computer account, I get a different error: The following error occurred attempting to join the domain "ITIA": The specified account already exists. (Note that until a while ago samba wasn't configured to automatically create computer accounts. What I did whenever I wanted an XP to join was to manually create it. When I first attempted to solve the Windows 7 join problem, I setup samba to do this automatically, as this is what most people do, as I understand, and I thought that it might be related. I haven't attempted to add an XP since I made this change, so I don't know if it works, but whether it works or not, the problem remains.) Update 1: Here are the relevant parts of smb.conf: [global] panic action = /usr/share/samba/panic-action %d workgroup = ITIA server string = Itia file server announce as = NT interfaces = 147.102.160.1 volume = %h passdb backend = ldapsam:ldap://ldap.itia.ntua.gr:389 ldap admin dn = uid=samba,ou=daemons,dc=itia,dc=ntua,dc=gr ldap ssl = off ldap suffix = dc=itia,dc=ntua,dc=gr ldap user suffix = ou=people ldap group suffix = ou=groups ldap machine suffix = ou=computers unix password sync = no add machine script = smbldap-useradd -w -i %u log file = /var/log/samba/samba-log.all log level = 3 max log size = 5000 syslog = 2 socket options = SO_KEEPALIVE TCP_NODELAY encrypt passwords = true password level = 1 security = user domain master = yes local master = no wins support = yes domain logons = yes idmap gid = 1000-2000 Update 2: The server has a single network interface eth1 (also an unused eth0 that shows up only in the kernel boot messages) and two ip addresses; the main, 147.102.160.1, and an additional one, 147.102.160.37, that comes up with "ip addr add 147.102.160.37/32 dev eth1" (used only for a web site that has a different certificate than other web sites served from the same machine). One of the problems I recently faced was that samba was using the latter IP address. I fixed that by adding the "interfaces = 147.102.160.1" statement in smb.conf. Now: acheloos:/etc/apache2# tcpdump host 147.102.160.40 and not port 5900 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 13:13:56.549048 IP lithaios.itia.civil.ntua.gr.netbios-dgm > 147.102.160.255.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549056 ARP, Request who-has acheloos2.itia.civil.ntua.gr tell lithaios.itia.civil.ntua.gr, length 46 13:13:56.549091 ARP, Reply acheloos2.itia.civil.ntua.gr is-at 00:10:4b:b4:9e:59 (oui Unknown), length 28 13:13:56.549324 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549608 IP lithaios.itia.civil.ntua.gr.netbios-dgm > acheloos2.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549741 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.550364 IP lithaios.itia.civil.ntua.gr.netbios-dgm > acheloos.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.550468 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) (acheloos2 is the second IP address, 147.102.160.37). The above dump occurs when I click "OK" (to join the domain), until it asks me for the username and password of a user that can join the domain. I don't know why the client is contacting the second IP address. I tried temporarily deactivating it, but I still had some related ARP traffic (though I think not IP traffic).

  Read the article

• What is the best server or Ip address to use for prolonged testing?

  - by eldorel

  I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

  Read the article

• Installing .NET application on IIS 7.5 issues

  - by Juw

  Really need some help here. I am at a loss. I am trying to install a webservice that some other guy wrote in .NET. I have some basic IIS understanding. The webservice works just fine on my dev computer. But now i try to move the webservice to a production server and bad things happens. The webservice has been located in C:\inetpub\wwwroot\ dir on the dev server. But on this production server it is to be located in D:\services\ I have managed to install an application on the production server and everything seems fine and dandy. But when i "Test Settings" in the initial setup i get "Invalid application path" error. But i can just close it down and still install it. But when i try to access the webservice with: http://myserver.com/webservice/GetData nothing happens. Just a blank page and when i check the response headers...500 error. I don´t know what is going on here or where the problem is. I post the config file here so someone hopefully might notice something odd. Thanx in advance! EDIT: The config file is from my dev server. I just copied it to my production server...but that obviously didn´t work :-) UPDATE: I noticed that my dev server run in an Application pool with Net 4 and in "classic" "mode". On the production server it was in NET 4 but in "integrated" mode. So i changed it to "classic". I still get a blank page. But checking the log will output this: 2012-10-03 14:57:00 ip removed GET /boo/GetData - 80 - ip removed Mozilla/5.0+(Windows+NT+6.1;+WOW64;+rv:15.0)+Gecko/20100101+Firefox/15.0.1 404 2 1260 203 <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.web> <identity impersonate="true" /> <!-- Impersonate NT AUTHORITY/IUSR --> <compilation targetFramework="4.0"> <assemblies> <add assembly="System.Data.Entity, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b7735c561131e089" /> </assemblies> </compilation> <pages controlRenderingCompatibilityVersion="3.5" clientIDMode="AutoID" /> </system.web> <system.webServer> <modules runAllManagedModulesForAllRequests="true" /> <httpErrors existingResponse="PassThrough" /> <httpProtocol> <customHeaders> <add name="Access-Control-Allow-Origin" value="*" /> </customHeaders> </httpProtocol> <directoryBrowse enabled="false" /> </system.webServer> <system.serviceModel> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> <standardEndpoints> <webHttpEndpoint> <!-- Configure the WCF REST service base address via the global.asax.cs file and the default endpoint via the attributes on the <standardEndpoint> element below --> <standardEndpoint name="" helpEnabled="true" automaticFormatSelectionEnabled="true" /> </webHttpEndpoint> </standardEndpoints> </system.serviceModel> <connectionStrings> <add name="Entities" connectionString="metadata=res://*/DataModel.csdl|res://*/DataModel.ssdl|res://*/DataModel.msl;provider=System.Data.SqlClient;provider connection string=&quot;data source=someip;initial catalog=db_90;User ID=user1;Password=access2;multipleactiveresultsets=True;App=EntityFramework&quot;" providerName="System.Data.EntityClient" /> </connectionStrings> </configuration>

  Read the article

• LXC Container Networking

  - by digitaladdictions

  I just started to experiment with LXC containers. I was able to create a container and start it up but I cannot get dhcp to assign the container an IP address. If I assign a static address the container can ping the host IP but not outside the host IP. The host is CentOS 6.5 and the guest is Ubuntu 14.04LTS. I used the template downloaded by lxc-create -t download -n cn-01 command. If I am trying to get an IP address on the same subnet as the host I don't believe I should need the IP tables rule for masquerading but I added it anyways. Same with IP forwarding. I compiled LXC by hand from the following source https://linuxcontainers.org/downloads/lxc-1.0.4.tar.gz Host Operating System Version #> cat /etc/redhat-release CentOS release 6.5 (Final) #> uname -a Linux localhost.localdomain 2.6.32-431.20.3.el6.x86_64 #1 SMP Thu Jun 19 21:14:45 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Container Config #> cat /usr/local/var/lib/lxc/cn-01/config # Template used to create this container: /usr/local/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.container.conf(5) # Distribution configuration lxc.include = /usr/local/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /usr/local/var/lib/lxc/cn-01/rootfs lxc.utsname = cn-01 # Network configuration lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 LXC default.confu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:f #> cat /usr/local/etc/lxc/default.conf lxc.network.type = veth lxc.network.link = br0 lxc.network.flags = up #> lxc-checkconfig Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-2.6.32-431.20.3.el6.x86_64 --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: /usr/local/bin/lxc-checkconfig: line 103: [: too many arguments enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: /usr/local/bin/lxc-checkconfig: line 118: [: -gt: unary operator expected Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/local/bin/lxc-checkconfig Network Config (HOST) #> cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=dhcp ONBOOT=yes #> cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes TYPE=Ethernet IPV6INIT=no USERCTL=no BRIDGE=br0 #> cat /etc/networks default 0.0.0.0 loopback 127.0.0.0 link-local 169.254.0.0 #> ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 42:7e:43:b3:61:c5 brd ff:ff:ff:ff:ff:ff 4: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet 10.60.70.121/24 brd 10.60.70.255 scope global br0 inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 12: vethT6BGL2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fe:a1:69:af:50:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::fca1:69ff:feaf:5017/64 scope link valid_lft forever preferred_lft forever #> brctl show bridge name bridge id STP enabled interfaces br0 8000.000c291230f2 no eth0 vethT6BGL2 pan0 8000.000000000000 no #> cat /proc/sys/net/ipv4/ip_forward 1 # Generated by iptables-save v1.4.7 on Fri Jul 11 15:11:36 2014 *nat :PREROUTING ACCEPT [34:6287] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Jul 11 15:11:36 2014 Network Config (Container) #> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp #> ip a s 11: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 02:69:fb:42:ee:d7 brd ff:ff:ff:ff:ff:ff inet6 fe80::69:fbff:fe42:eed7/64 scope link valid_lft forever preferred_lft forever 13: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever

  Read the article

• my asp.net mvc 2.0 application fails with error "No parameterless constructor defined for this objec

  - by loviji

  Hello, i'm new in asp.net mvc 2. I'm trying to list all data from one table(ms sql server table). as ORM I use Entity Framework. now, I'm tried to write something to do this: Model: private uqsEntities _uqsEntity; public permissionRepository(uqsEntities uqsEntity) { _uqsEntity = uqsEntity; } public IEnumerable<userPermissions> getAllData() { return _uqsEntity.userPermissions; } controller: private DataManager _dataManager; public ManagePermissionsController(DataManager datamanager) { _dataManager = datamanager; } public ActionResult Index() { return RedirectToAction("List"); } [AcceptVerbs(HttpVerbs.Get)] public ActionResult List() { return List(null); } [AcceptVerbs(HttpVerbs.Post)] public ActionResult List(int? userID) { return View(_dataManager.Permission.getAllData().ToList()); } Route: routes.MapRoute( "ManagePerm", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "ManagePermissions", action = "Index"}, new string[] { "uqs.Controllers" } // Parameter defaults ); and View automatically generated by Visual Studio(in action mouse right-click). when I run app. , my app. fails. No parameterless constructor defined for this object. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.MissingMethodException: No parameterless constructor defined for this object. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [MissingMethodException: No parameterless constructor defined for this object.] System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck) +0 System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache) +86 System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache) +230 System.Activator.CreateInstance(Type type, Boolean nonPublic) +67 System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +80 [InvalidOperationException: An error occurred when trying to create a controller of type 'uqs.Controllers.ManagePermissionsController'. Make sure that the controller has a parameterless public constructor.] System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +190 System.Web.Mvc.DefaultControllerFactory.CreateController(RequestContext requestContext, String controllerName) +68 System.Web.Mvc.MvcHandler.ProcessRequestInit(HttpContextBase httpContext, IController& controller, IControllerFactory& factory) +118 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContextBase httpContext, AsyncCallback callback, Object state) +46 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContext httpContext, AsyncCallback callback, Object state) +63 System.Web.Mvc.MvcHandler.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData) +13 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +8679186 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 please, somebody, help me to catch problem.

  Read the article

• Visual Studio build fails: unable to copy exe-file from obj\debug to bin\debug

  - by Nailuj

  This is a question asked before, both here on Stack Overflow and other places, but none of the suggestions I've found this far has helped me, so I just have to try asking a new question. Scenario: I have a simple Windows Forms application (C#, .NET 4.0, Visual Studio 2010). It has a couple of base forms that most other forms inherit from, it uses Entity Framework (and POCO classes) for database access. Nothing fancy, no multi-threading or anything. Problem: All was fine for a while. Then, all out of the blue, Visual Studio failed to build when I was about to launch the application. I got the warning "Unable to delete file '...bin\Debug\[ProjectName].exe'. Access to the path '...bin\Debug\[ProjectName].exe' is denied." and the error "Unable to copy file 'obj\x86\Debug\[ProjectName].exe' to 'bin\Debug\[ProjectName].exe'. The process cannot access the file 'bin\Debug\[ProjectName].exe' because it is being used by another process." (I get both the warning and the error when running Rebuild, but only the error when running Build - don't think that is relevant?) I understand perfectly fine what the warning and error message says: Visual Studio is obviously trying to overwrite the exe-file while it the same time has a lock on it for some reason. However, this doesn't help me find a solution to the problem... The only thing I've found working is to shut down Visual Studio and start it again. Building and launching then works, untill I make a change in some of the forms, then I have the same problem again and have to restart... Quite frustrating! As I mentioned above, this seems to be a known problem, so there are lots of suggested solutions. I'll just list what I've already tried here, so people know what to skip: Creating a new clean solution and just copy the files from the old solution. Adding the following to the following to the project's pre-build event: if exist "$(TargetPath).locked" del "$(TargetPath).locked"   if not exist "$(TargetPath).locked" if exist "$(TargetPath)" move "$(TargetPath)" "$(TargetPath).locked" Adding the following to the project properties (.csproj file): <GenerateResourceNeverLockTypeAssembliestrue</GenerateResourceNeverLockTypeAssemblies However, none of them worked for me, so you can probably see why I'm starting to get a bit frustrated. I don't know where else to look, so I hope somebody has something to give me! Is this a bug in VS, and if so is there a patch? Or has I done something wrong, do I have a circular reference or similar, and if so how could I find out? Any suggestions are highly appreciated :)

  Read the article

• VHDL - Problem with std_logic_vector

  - by wretrOvian

  Hi, i'm coding a 4-bit binary adder with accumulator: library ieee; use ieee.std_logic_1164.all; entity binadder is port(n,clk,sh:in bit; x,y:inout std_logic_vector(3 downto 0); co:inout bit; done:out bit); end binadder; architecture binadder of binadder is signal state: integer range 0 to 3; signal sum,cin:bit; begin sum<= (x(0) xor y(0)) xor cin; co<= (x(0) and y(0)) or (y(0) and cin) or (x(0) and cin); process begin wait until clk='0'; case state is when 0=> if(n='1') then state<=1; end if; when 1|2|3=> if(sh='1') then x<= sum & x(3 downto 1); y<= y(0) & y(3 downto 1); cin<=co; end if; if(state=3) then state<=0; end if; end case; end process; done<='1' when state=3 else '0'; end binadder; The output : -- Compiling architecture binadder of binadder ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(15): No feasible entries for infix operator "xor". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(15): Type error resolving infix expression "xor" as type std.standard.bit. ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): No feasible entries for infix operator "and". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): Bad expression in right operand of infix expression "or". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): No feasible entries for infix operator "and". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): Bad expression in left operand of infix expression "or". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): Bad expression in right operand of infix expression "or". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(16): Type error resolving infix expression "or" as type std.standard.bit. ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(28): No feasible entries for infix operator "&". ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(28): Type error resolving infix expression "&" as type ieee.std_logic_1164.std_logic_vector. ** Error: C:/Modeltech_pe_edu_6.5a/examples/binadder.vhdl(39): VHDL Compiler exiting I believe i'm not handling std_logic_vector's correctly. Please tell me how? :(

  Read the article

• How to set up default schema name in JPA configuration?

  - by Roman

  I found that in hibernate config file we could set up parameter hibernate.default_schema: <hibernate-configuration> <session-factory> ... <property name="hibernate.default_schema">myschema</property> ... </session-factory> </hibernate-configuration> Now I'm using JPA and I want to do the same. Otherwise I have to add parameter schema to each @Table annotation like: @Entity @Table (name = "projectcategory", schema = "SCHEMANAME") public class Category implements Serializable { ... } As I understand this parameter should be somewhere in this part of configuration: <bean id="domainEntityManagerFactory" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="persistenceUnitName" value="JiraManager"/> <property name="dataSource" ref="domainDataSource"/> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter"> <property name="generateDdl" value="false"/> <property name="showSql" value="false"/> <property name="databasePlatform" value="${hibernate.dialect}"/> </bean> </property> </bean> <bean id="domainDataSource" class="com.mchange.v2.c3p0.ComboPooledDataSource" destroy-method="close"> <property name="driverClass" value="${db.driver}" /> <property name="jdbcUrl" value="${datasource.url}" /> <property name="user" value="${datasource.username}" /> <property name="password" value="${datasource.password}" /> <property name="initialPoolSize" value="5"/> <property name="minPoolSize" value="5"/> <property name="maxPoolSize" value="15"/> <property name="checkoutTimeout" value="10000"/> <property name="maxStatements" value="150"/> <property name="testConnectionOnCheckin" value="true"/> <property name="idleConnectionTestPeriod" value="50"/> </bean> ... but I can't find its name in google. Any ideas?

  Read the article

• java 7 upgrade and hibernate annotation processor error

  - by Bill Turner

  I am getting the following warning, which seems to be triggering a subsequent warning and an error. I have been googling like mad, though have not found anything that makes it clear what it is I should do to resolve this. This issue occurs when I execute an Ant build. I am trying to migrate our project to Java 7. I have changed all the source='1.6' and target="1.6" to 1.7. I did find this related article: Forward compatible Java 6 annotation processor and SupportedSourceVersion It seems to indicate that I should build the Hibernate annotation processor jar myself, compiling it with with 1.7. It does not seem I should be required to do so. The latest version of the class in question (in hibernate-validator-annotation-processor-5.0.1.Final.jar) has been compiled with 1.6. Since the code in said class refers to SourceVersion.latestSupported(), and the 1.6 of that returns only RELEASE_6, there does not seem to be a generally available solution. Here is the warning: [javac] warning: Supported source version 'RELEASE_6' from annotation processor 'org.hibernate.validator.ap.ConstraintValidationProcessor' less than -source '1.7' And, here are the subsequent warnings/error. [javac] warning: No processor claimed any of these annotations: javax.persistence.PersistenceContext,javax.persistence.Column,org.codehaus.jackson.annotate.JsonIgnore,javax.persistence.Id,org.springframework.context.annotation.DependsOn,com.trgr.cobalt.infrastructure.datasource.Bucketed,org.codehaus.jackson.map.annotate.JsonDeserialize,javax.persistence.DiscriminatorColumn,com.trgr.cobalt.dataroom.authorization.secure.Secured,org.hibernate.annotations.GenericGenerator,javax.annotation.Resource,com.trgr.cobalt.infrastructure.spring.domain.DomainField,org.codehaus.jackson.annotate.JsonAutoDetect,javax.persistence.DiscriminatorValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionMandatory,org.springframework.stereotype.Repository,javax.persistence.GeneratedValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactional,org.hibernate.annotations.Cascade,javax.persistence.Table,javax.persistence.Enumerated,org.hibernate.annotations.FilterDef,javax.persistence.OneToOne,com.trgr.cobalt.dataroom.datasource.config.core.CoreEntity,org.springframework.transaction.annotation.Transactional,com.trgr.cobalt.infrastructure.util.enums.EnumConversion,org.springframework.context.annotation.Configuration,com.trgr.cobalt.infrastructure.spring.domain.UpdatedFields,com.trgr.cobalt.infrastructure.spring.documentation.SampleValue,org.springframework.context.annotation.Bean,org.codehaus.jackson.annotate.JsonProperty,javax.persistence.Basic,org.codehaus.jackson.map.annotate.JsonSerialize,com.trgr.cobalt.infrastructure.spring.validation.Required,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionNever,org.springframework.context.annotation.Profile,com.trgr.cobalt.infrastructure.spring.stereotype.Persistor,javax.persistence.Transient,com.trgr.cobalt.infrastructure.spring.validation.NotNull,javax.validation.constraints.Size,javax.persistence.Entity,javax.persistence.PrimaryKeyJoinColumn,org.hibernate.annotations.BatchSize,org.springframework.stereotype.Service,org.springframework.beans.factory.annotation.Value,javax.persistence.Inheritance [javac] error: warnings found and -Werror specified TIA!

  Read the article

• NullReferenceException when calling InsertOnSubmit in Linq to Sql.

  - by Charlie

  I'm trying to insert a new object into my database using LINQ to SQL but get a NullReferenceException when I call InsertOnSubmit() in the code snippet below. I'm passing in a derived class called FileUploadAudit, and all properties on the object are set. public void Save(Audit audit) { try { using (ULNDataClassesDataContext dataContext = this.Connection.GetContext()) { if (audit.AuditID > 0) { throw new RepositoryException(RepositoryExceptionCode.EntityAlreadyExists, string.Format("An audit entry with ID {0} already exists and cannot be updated.", audit.AuditID)); } dataContext.Audits.InsertOnSubmit(audit); dataContext.SubmitChanges(); } } catch (Exception ex) { if (ObjectFactory.GetInstance<IExceptionHandler>().HandleException(ex)) { throw; } } } Here's the stack trace: at System.Data.Linq.Table`1.InsertOnSubmit(TEntity entity) at XXXX.XXXX.Repository.AuditRepository.Save(Audit audit) C:\XXXX\AuditRepository.cs:line 25" I've added to the Audit class like this: public partial class Audit { public Audit(string message, ULNComponent component) : this() { this.Message = message; this.DateTimeRecorded = DateTime.Now; this.SetComponent(component); this.ServerName = Environment.MachineName; } public bool IsError { get; set; } public void SetComponent(ULNComponent component) { this.Component = Enum.GetName(typeof(ULNComponent), component); } } And the derived FileUploadAudit looks like this: public class FileUploadAudit : Audit { public FileUploadAudit(string message, ULNComponent component, Guid fileGuid, string originalFilename, string physicalFilename, HttpPostedFileBase postedFile) : base(message, component) { this.FileGuid = fileGuid; this.OriginalFilename = originalFilename; this.PhysicalFileName = physicalFilename; this.PostedFile = postedFile; this.ValidationErrors = new List<string>(); } public Guid FileGuid { get; set; } public string OriginalFilename { get; set; } public string PhysicalFileName { get; set; } public HttpPostedFileBase PostedFile { get; set; } public IList<string> ValidationErrors { get; set; } } Any ideas what the problem is? The closest question I could find to mine is here but my partial Audit class is calling the parameterless constructor in the generated code, and I still get the problem. UPDATE: This problem only occurs when I pass in the derived FileUploadAudit class, the Audit class works fine. The Audit class is generated as a linq to sql class and there are no Properties mapped to database fields in the derived class.

  Read the article

• Using Joda DateTime as a Jersey parameter?

  - by HolySamosa

  I'd like to use Joda's DateTime for query parameters in Jersey, but this isn't supported by Jersey out-of-the-box. I'm assuming that implementing an InjectableProvider is the proper way to add DateTime support. Can someone point me to a good implementation of an InjectableProvider for DateTime? Or is there an alternative approach worth recommending? (I'm aware I can convert from Date or String in my code, but this seems like a lesser solution). Thanks. Solution: I modified Gili's answer below to use the @Context injection mechanism in JAX-RS rather than Guice. import com.sun.jersey.core.spi.component.ComponentContext; import com.sun.jersey.spi.inject.Injectable; import com.sun.jersey.spi.inject.PerRequestTypeInjectableProvider; import java.util.List; import javax.ws.rs.QueryParam; import javax.ws.rs.WebApplicationException; import javax.ws.rs.core.Context; import javax.ws.rs.core.Response; import javax.ws.rs.core.Response.Status; import javax.ws.rs.core.UriInfo; import javax.ws.rs.ext.Provider; import org.joda.time.DateTime; /** * Enables DateTime to be used as a QueryParam. * <p/> * @author Gili Tzabari */ @Provider public class DateTimeInjector extends PerRequestTypeInjectableProvider<QueryParam, DateTime> { private final UriInfo uriInfo; /** * Creates a new DateTimeInjector. * <p/> * @param uriInfo an instance of {@link UriInfo} */ public DateTimeInjector( @Context UriInfo uriInfo) { super(DateTime.class); this.uriInfo = uriInfo; } @Override public Injectable<DateTime> getInjectable(final ComponentContext cc, final QueryParam a) { return new Injectable<DateTime>() { @Override public DateTime getValue() { final List<String> values = uriInfo.getQueryParameters().get(a.value()); if( values == null || values.isEmpty()) return null; if (values.size() > 1) { throw new WebApplicationException(Response.status(Status.BAD_REQUEST). entity(a.value() + " may only contain a single value").build()); } return new DateTime(values.get(0)); } }; } }

  Read the article

• Download a file with DefaultHTTPClient and preemptive authentication

  - by Nils

  After I had a lot of problems with preemptive authentication , I got it finally working. Now the next problem. I want to get a file with it, but I don't know how. I thought the file data might be in the variable response, but it isn't. Any ideas how this might work? I'm trying it since days without success :( - Basically I'm trying to download an jpeg file, which is on a server protected by prem. auth. // BASIC AUTH /* * ==================================================================== * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. * The ASF licenses this file to You under the Apache License, Version 2.0 * (the "License"); you may not use this file except in compliance with * the License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ==================================================================== * * This software consists of voluntary contributions made by many * individuals on behalf of the Apache Software Foundation. For more * information on the Apache Software Foundation, please see * <http://www.apache.org/>. */ //http://svn.apache.org/repos/asf/httpcomponents/httpclient/branches/4.0.x/httpclient/src/examples/org/apache/http/examples/client/ClientPreemptiveBasicAuthentication.java httpclient = new DefaultHttpClient(); httpclient.getCredentialsProvider().setCredentials( new AuthScope(host, port), new UsernamePasswordCredentials(username, password)); // Generate BASIC scheme object and stick it to the local // execution context BasicHttpContext localcontext = new BasicHttpContext(); BasicScheme basicAuth = new BasicScheme(); localcontext.setAttribute("preemptive-auth", basicAuth); //first request interceptor httpclient.addRequestInterceptor(new PreemptiveAuth(), 0); HttpHost targetHost = new HttpHost(host, port, "http"); //HttpGet httpget = new HttpGet("/"); HttpGet httpget = new HttpGet(http.url); System.out.println("executing request" + httpget.getRequestLine()); /// !!! HttpResponse response = httpclient.execute(targetHost, httpget, localcontext); HttpEntity entity = response.getEntity(); System.out.println("----------------------------------------"); System.out.println("+"+response.getStatusLine()+"+"); ...

  Read the article

• Why is ListBoxFor not selecting items, but ListBox is?

  - by Roger Rogers

  I have the following code in my view: <%= Html.ListBoxFor(c => c.Project.Categories, new MultiSelectList(Model.Categories, "Id", "Name", new List<int> { 1, 2 }))%> <%= Html.ListBox("MultiSelectList", new MultiSelectList(Model.Categories, "Id", "Name", new List<int> { 1, 2 }))%> The only difference is that the first helper is strongly typed (ListBoxFor), and it fails to show the selected items (1,2), even though the items appear in the list, etc. The simpler ListBox is working as expected. I'm obviously missing something here. I can use the second approach, but this is really bugging me and I'd like to figure it out. For reference, my model is: public class ProjectEditModel { public Project Project { get; set; } public IEnumerable<Project> Projects { get; set; } public IEnumerable<Client> Clients { get; set; } public IEnumerable<Category> Categories { get; set; } public IEnumerable<Tag> Tags { get; set; } public ProjectSlide SelectedSlide { get; set; } } Update I just changed the ListBox name to Project.Categories (matching my model) and it now FAILS to select the item. <%= Html.ListBox("Project.Categories", new MultiSelectList(Model.Categories, "Id", "Name", new List<int> { 1, 2 }))%> I'm obviously not understanding the magic that is happening here. Update 2 Ok, this is purely naming, for example, this works... <%= Html.ListBox("Project_Tags", new MultiSelectList(Model.Tags, "Id", "Name", Model.Project.Tags.Select(t => t.Id)))%> ...because the field name is Project_Tags, not Project.Tags, in fact, anything other than Tags or Project.Tags will work. I don't get why this would cause a problem (other than that it matches the entity name), and I'm not good enough at this to be able to dig in and find out.

  Read the article

• Rendering a WPF Network Map/Graph layout - Manual? PathListBox? Something Else?

  - by Ben Von Handorf

  I'm writing code to present the user with a simplified network map. At any given time, the map is focused on a specific item... say a router or a server. Based on the focused item, other network entities are grouped into sets (i.e. subnets or domains) and then rendered around the focused item. Lines would represent connections and groups would be visually grouped inside a rectangle or ellipse. Panning and zooming are required features. An item can be selected to display more information in a "properties" style window. An item could also be double-clicked to re-focus the entire network map on that item. At that point, the entire map would be re-calculated. I am using MVVM without any framework, as of yet. Assume the logic for grouping items and determining what should be shown or not is all in place. I'm looking for the best way to approach the UI layout. So far, I'm aware of the following options: Use a canvas for layout (inside a ScrollViewer to handle the panning). Have my ViewModel make use of a Layout Manager type of class, which would handle assigning all the layout properties (Top, Left, etc.). Bind my set of display items to an ItemsControl and use Data Templates to handle the actual rendering. The drawbacks with this approach: Highly manual layout on my part. Lots of calculation. I have to handle item selection manually. Computation of connecting lines is manual. The Pros of this approach: I can draw additional lines between child subnets as appropriate (manually). Additional LayoutManagers could be added later to render the display differently. This could probably be wrapped up into some sort of a GraphLayout control to be re-used. Present the focused item at the center of the display and then use a PathListBox for layout of the additional items. Have my ViewModel expose a simple list of things to be drawn and bind them to the PathListBox. Override the ListBoxItem Template to also create a line geometry from the borders of the focused item (tricky) to the bound item. Use DataTemplates to handle the case where the item being bound is a subnet, in which case we would use another PathListBox in the template to display items inside the subnet. The drawbacks with this approach: Selected Item synchronization across multiple `PathListBox`es. Only one item on the whole graph can be selected at a time, but each child PathListBox maintains its own selection. Also, subnets cannot be selected, but would be selectable without additional work. Drawing the connecting lines is going to be a bit of trickery in the ListBoxItem template, since I need to know the correct side of the focused item to connect to. The pros of this approach: I get to stay out of the layout business, more. I'm looking for any advice or thoughts from others who have encountered similar issues or who have more WPF experience than I. I'm using WPF 4, so any new tricks are legal and encouraged.

  Read the article

• .NET Interface with AutoCAD -- SetXData errors.

  - by Jerry

  I am trying to use the SetXData method on the AutoCAD 2007 COM object, but it is throwing errors. Example Test: public AcadEntity getAcadEntity() { /// ... Basic code to return a single AutoCAD entity... } private void btnTagItem_Click(object sender, EventArgs e) { AcadEntity ent = getAcadEntity(); short[] xDataType; string[] xDataStrings; DrawingXData xData = new DrawingXData(); xData.field1 = "Some Text Goes here"; xData.field2 = 1; xData.field3 = 100; xData.field4 = 1509.2; xData.field5 = "More Text"; BuildXData("AutoCad_App_Name", xData, out xDataType, out xDataStrings); ent.SetXData(xDataType, xDataStrings); // This line crashes. } private void BuildXData(string applicationName, DrawingXData xData, out short[] xDataType, out string[] xDataStrings) { List<short> dataTypes = new List<short>(); List<string> dataStrings = new List<string>(); /// Code types... /// 1000 == String up to 255 bytes /// 1001 == Application Name // Set Applicaiton Name dataTypes.Add(1001); dataStrings.Add(applicationName); // Set Application Data dataTypes.Add(1000); dataStrings.Add(xData.field1.ToString()); dataTypes.Add(1000); dataStrings.Add(xData.field2.ToString()); dataTypes.Add(1000); dataStrings.Add(xData.field3.ToString()); dataTypes.Add(1000); dataStrings.Add(xData.field4.ToString()); dataTypes.Add(1000); dataStrings.Add(xData.field5.ToString()); // ... etc. xDataType = dataTypes.ToArray(); xDataStrings = dataStrings.ToArray(); } The error I get is "Invalid argument data in SetXData method". The error code (if this helps anyone) is -2145320939. The main reason I'm posting is because the same code in a very old VB6 application works just fine. I'm stumped.

  Read the article

• C# Silverlight - Delay Child Window Load?!

  - by Goober

  The Scenario Currently I have a C# Silverlight Application That uses the domainservice class and the ADO.Net Entity Framework to communicate with my database. I want to load a child window upon clicking a button with some data that I retrieve from a server-side query to the database. The Process The first part of this process involves two load operations to load separate data from 2 tables. The next part of the process involves combining those lists of data to display in a listbox. The Problem The problem with this is that the first two asynchronous load operations haven't returned the data by the time the section of code to combine these lists of data is reached, thus result in a null value exception..... Initial Load Operations To Get The Data: public void LoadAudits(Guid jobID) { var context = new InmZenDomainContext(); var imageLoadOperation = context.Load(context.GetImageByIDQuery(jobID)); imageLoadOperation.Completed += (sender3, e3) => { imageList = ((LoadOperation<InmZen.Web.Image>)sender3).Entities.ToList(); }; var auditLoadOperation = context.Load(context.GetAuditByJobIDQuery(jobID)); auditLoadOperation.Completed += (sender2, e2) => { auditList = ((LoadOperation<Audit>)sender2).Entities.ToList(); }; } I Then Want To Execute This Immediately: IEnumerable<JobImageAudit> jobImageAuditList = from a in auditList join ai in imageList on a.ImageID equals ai.ImageID select new JobImageAudit { JobID = a.JobID, ImageID = a.ImageID.Value, CreatedBy = a.CreatedBy, CreatedDate = a.CreatedDate, Comment = a.Comment, LowResUrl = ai.LowResUrl, }; auditTrailList.ItemsSource = jobImageAuditList; However I can't because the async calls haven't returned with the data yet... Thus I have to do this (Perform the Load Operations, Then Press A Button On The Child Window To Execute The List Concatenation and binding): private void LoadAuditsButton_Click(object sender, RoutedEventArgs e) { IEnumerable<JobImageAudit> jobImageAuditList = from a in auditList join ai in imageList on a.ImageID equals ai.ImageID select new JobImageAudit { JobID = a.JobID, ImageID = a.ImageID.Value, CreatedBy = a.CreatedBy, CreatedDate = a.CreatedDate, Comment = a.Comment, LowResUrl = ai.LowResUrl, }; auditTrailList.ItemsSource = jobImageAuditList; } Potential Ideas for Solutions: Delay the child window displaying somehow? Potentially use DomainDataSource and the Activity Load control?! Any thoughts, help, solutions, samples comments etc. greatly appreciated.

  Read the article

• NHibernate: No persister error

  - by Mike

  Hello, In my quest to further my knowledge, I'm trying to get get NHibernate running. I have the following structure to my solution Core Class Library Project Infrastructure Class Library Project MVC Application Project Test Project In my Core project I have created the following entity: using System; namespace Core.Domain.Model { public class Category { public virtual Guid Id { get; set; } public virtual string Name { get; set; } } } In my Infrastructure Project I have the following mapping: <?xml version="1.0" encoding="utf-8" ?> <hibernate-mapping xmlns="urn:nhibernate-mapping-2.2" namespace="Core.Domain.Model" assembly="Core"> <class name="Category" table="Categories" dynamic-update="true"> <cache usage="read-write"/> <id name="Id" column="Id" type="Guid"> <generator class="guid"/> </id> <property name="Name" length="100"/> </class> </hibernate-mapping> With the following config file: <hibernate-configuration xmlns="urn:nhibernate-configuration-2.2"> <session-factory> <property name="connection.driver_class">NHibernate.Driver.SqlClientDriver</property> <property name="connection.connection_string">server=xxxx;database=xxxx;Integrated Security=true;</property> <property name="show_sql">true</property> <property name="dialect">NHibernate.Dialect.MsSql2008Dialect</property> <property name="cache.use_query_cache">false</property> <property name="adonet.batch_size">100</property> <property name="proxyfactory.factory_class">NHibernate.ByteCode.Castle.ProxyFactoryFactory, NHibernate.ByteCode.Castle</property> <mapping assembly="Infrastructure" /> </session-factory> </hibernate-configuration> In my test project, I have the following Test [TestMethod] [DeploymentItem("hibernate.cfg.xml")] public void CanCreateCategory() { IRepository<Category> repo = new CategoryRepository(); Category category = new Category(); category.Name = "ASP.NET"; repo.Save(category); } I get the following error when I try to run the test: Test method Volunteer.Tests.CategoryTests.CanCreateCategory threw exception: NHibernate.MappingException: No persister for: Core.Domain.Model.Category. Any help would be greatly appreciated. I do have the cfg build action set to embedded resource. Thanks!

  Read the article

• ASP.NET MVC ViewModel Pattern

  - by Omu

  EDIT: I made something much better to fill and read data from a view using ViewModels, called it ValueInjecter. http://valueinjecter.codeplex.com/documentation using the ViewModel to store the mapping logic was not such a good idea because there was repetition and SRP violation, but now with the ValueInjecter I have clean ViewModels and dry mapping code I made a ViewModel pattern for editing stuff in asp.net mvc this pattern is usefull when you have to make a form for editing an entity and you have to put on the form some dropdowns for the user to choose some values public class OrganisationViewModel { //paramterless constructor required, cuz we are gonna get an OrganisationViewModel object from the form in the post save method public OrganisationViewModel() : this(new Organisation()) {} public OrganisationViewModel(Organisation o) { Organisation = o; Country = new SelectList(LookupFacade.Country.GetAll(), "ID", "Description", CountryKey); } //that's the Type for whom i create the viewmodel public Organisation Organisation { get; set; } #region DropDowns //for each dropdown i have a int? Key that stores the selected value public IEnumerable<SelectListItem> Country { get; set; } public int? CountryKey { get { if (Organisation.Country != null) { return Organisation.Country.ID; } return null; } set { if (value.HasValue) { Organisation.Country = LookupFacade.Country.Get(value.Value); } } } #endregion } and that's how i use it public ViewResult Edit(int id) { var model = new OrganisationViewModel(organisationRepository.Get(id)); return View(model); } [AcceptVerbs(HttpVerbs.Post)] public ActionResult Edit(OrganisationViewModel model) { organisationRepository.SaveOrUpdate(model.Organisation); return RedirectToAction("Index"); } and the markup <p> <label for="Name"> Name:</label> <%= Html.Hidden("Organisation.ID", Model.Organisation.ID)%> <%= Html.TextBox("Organisation.Name", Model.Organisation.Name)%> <%= Html.ValidationMessage("Organisation.Name", "*")%> </p> <p> ... <label for="CountryKey"> Country:</label> <%= Html.DropDownList("CountryKey", Model.Country, "please select") %> <%= Html.ValidationMessage("CountryKey", "*") %> </p> so tell me what you think about it

  Read the article

• Opinions on sensor / reading / alert database design

  - by Mark

  I've asked a few questions lately regarding database design, probably too many ;-) However I beleive I'm slowly getting to the heart of the matter with my design and am slowly boiling it down. I'm still wrestling with a couple of decisions regarding how "alerts" are stored in the database. In this system, an alert is an entity that must be acknowledged, acted upon, etc. Initially I related readings to alerts like this (very cut down) : - [Location] LocationId [Sensor] SensorId LocationId UpperLimitValue LowerLimitValue [SensorReading] SensorReadingId Value Status Timestamp [SensorAlert] SensorAlertId [SensorAlertReading] SensorAlertId SensorReadingId The last table is associating readings with the alert, because it is the reading that dictate that the sensor is in alert or not. The problem with this design is that it allows readings from many sensors to be associated with a single alert - whereas each alert is for a single sensor only and should only have readings for that sensor associated with it (should I be bothered that the DB allows this though?). I thought to simplify things, why even bother with the SensorAlertReading table? Instead I could do this: [Location] LocationId [Sensor] SensorId LocationId [SensorReading] SensorReadingId SensorId Value Status Timestamp [SensorAlert] SensorAlertId SensorId Timestamp [SensorAlertEnd] SensorAlertId Timestamp Basically I'm not associating readings with the alert now - instead I just know that an alert was active between a start and end time for a particular sensor, and if I want to look up the readings for that alert I can do. Obviously the downside is I no longer have any constraint stopping me deleting readings that occurred during the alert, but I'm not sure that the constraint is neccessary. Now looking in from the outside as a developer / DBA, would that make you want to be sick or does it seem reasonable? Is there perhaps another way of doing this that I may be missing? Thanks. EDIT: Here's another idea - it works in a different way. It stores each sensor state change, going from normal to alert in a table, and then readings are simply associated with a particular state. This seems to solve all the problems - what d'ya think? (the only thing I'm not sure about is calling the table "SensorState", I can't help think there's a better name (maybe SensorReadingGroup?) : - [Location] LocationId [Sensor] SensorId LocationId [SensorState] SensorStateId SensorId Timestamp Status IsInAlert [SensorReading] SensorReadingId SensorStateId Value Timestamp There must be an elegant solution to this!

  Read the article

• Fluent NHibernate - How to map a non nullable foreign key that exists in two joined tables

  - by vakman

  I'm mapping a set of membership classes for my application using Fluent NHibernate. I'm mapping the classes to the asp.net membership database structure. The database schema relevant to the problem looks like this: ASPNET_USERS UserId PK ApplicationId FK NOT NULL other user columns ... ASPNET_MEMBERSHIP UserId PK,FK ApplicationID FK NOT NULL other membership columns... There is a one to one relationship between these two tables. I'm attempting to join the two tables together and map data from both tables to a single 'User' entity which looks like this: public class User { public virtual Guid Id { get; set; } public virtual Guid ApplicationId { get; set; } // other properties to be mapped from aspnetuser/membership tables ... My mapping file is as follows: public class UserMap : ClassMap<User> { public UserMap() { Table("aspnet_Users"); Id(user => user.Id).Column("UserId").GeneratedBy.GuidComb(); Map(user => user.ApplicationId); // other user mappings Join("aspnet_Membership", join => { join.KeyColumn("UserId"); join.Map(user => user.ApplicationId); // Map other things from membership to 'User' class } } } If I try to run with the code above I get a FluentConfiguration exception Tried to add property 'ApplicationId' when already added. If I remove the line "Map(user = user.ApplicationId);" or change it to "Map(user = user.ApplicationId).Not.Update().Not.Insert();" then the application runs but I get the following exception when trying to insert a new user: Cannot insert the value NULL into column 'ApplicationId', table 'ASPNETUsers_Dev.dbo.aspnet_Users'; column does not allow nulls. INSERT fails. The statement has been terminated. And if I leave the .Map(user = user.ApplicationId) as it originally was and make either of those changes to the join.Map(user = user.ApplicationId) then I get the same exception above except of course the exception is related to an insert into the aspnet_Membership table So... how do I do this kind of mapping assuming I can't change my database schema?

  Read the article

• Problem with delete operation in many to many relation

  - by Alexey Zakharov

  Hi, I've got to classes Product and Store which have many to many relation I want deleting of store not to cause deleting of related product And deleting of product not to cause deleting of related store. Currently deleting of entity cause exception due to Foreign Key constraint. Here is this classes and their mapping in fluent hibernate: public class Product { public Product() { this.StoresStockedIn = new List<Store>(); } public virtual string Name { get; set; } public virtual double Price { get; set; } public virtual long ProductID { get; set; } public virtual IList<Store> StoresStockedIn { get; set; } } public class Store { public Store() { this.Products = new List<Product>(); this.Staff = new List<Employee>(); } public virtual string Name { get; set; } public virtual IList<Product> Products { get; set; } public virtual IList<Employee> Staff { get; set; } public virtual long StoreID { get; set; } } public class ProductMap : ClassMap<Product> { public ProductMap() { this.Id(x => x.ProductID); this.Map(x => x.Name); this.Map(x => x.Price); this.HasManyToMany(x => x.StoresStockedIn) .Cascade.None() .Table("StoreProduct"); } public class StoreMap : ClassMap<Store> { public StoreMap() { this.Id(x => x.StoreID); this.Map(x => x.Name); this.HasManyToMany(x => x.Products) .Cascade.None() .Inverse() .Table("StoreProduct"); this.HasMany(x => x.Staff) .Cascade.All() .Inverse(); } } Thanks, Alexey Zakharov

  Read the article

• Perf4j Not Logging Correctly

  - by Jehud

  I setup some stop watch calls in my code to measure some code blocks and all the messages are going into my primary log and not into the timing log. The perfStats.log file gets created just fine but all the messages go to the root log which I didn't think was supposed to happen according to the docs I've read. Is there something obvious I'm missing here? perf4j tutorial link: http://perf4j.codehaus.org/devguide.html#Using_the_log4j_Appenders_to_Generate_Real-Time_Performance_Information Example code import org.apache.log4j.Logger; import org.perf4j.LoggingStopWatch; import org.perf4j.StopWatch; public class PerfLogger { /** * @param args */ public static void main(String[] args) { Logger logger = Logger.getLogger(PerfLogger.class.getName()); logger.info("Starting perf log test"); StopWatch stopWatch = new LoggingStopWatch("test time"); try { Thread.sleep(1000); } catch (InterruptedException e) { // TODO Auto-generated catch block e.printStackTrace(); } stopWatch.stop(); } } Example log4j.xml <log4j:configuration xmlns:log4j='http://jakarta.apache.org/log4j/'> <appender name="STDOUT-DEBUG" class="org.apache.log4j.ConsoleAppender"> <layout class="org.apache.log4j.PatternLayout"> <param name="ConversionPattern" value="%d %-5p [%t]%x %M (%F:%L) - %m%n"/> </layout> </appender> <!-- Perf4J appenders --> <!-- This AsyncCoalescingStatisticsAppender groups StopWatch log messages into GroupedTimingStatistics messages which it sends on the file appender defined below --> <appender name="CoalescingStatistics" class="org.perf4j.log4j.AsyncCoalescingStatisticsAppender"> <!-- The TimeSlice option is used to determine the time window for which all received StopWatch logs are aggregated to create a single GroupedTimingStatistics log. Here we set it to 10 seconds, overriding the default of 30000 ms --> <param name="TimeSlice" value="10000"/> <appender-ref ref="fileAppender"/> </appender> <!-- This file appender is used to output aggregated performance statistics --> <appender name="fileAppender" class="org.apache.log4j.FileAppender"> <param name="File" value="perfStats.log"/> <layout class="org.apache.log4j.PatternLayout"> <param name="ConversionPattern" value="%m%n"/> </layout> </appender> <!-- Loggers --> <!-- The Perf4J logger. Note that org.perf4j.TimingLogger is the value of the org.perf4j.StopWatch.DEFAULT_LOGGER_NAME constant. Also, note that additivity is set to false, which is usually what is desired - this means that timing statements will only be sent to this logger and NOT to upstream loggers. --> <logger name="org.perf4j.TimingLogger" additivity="false"> <level value="INFO"/> <appender-ref ref="CoalescingStatistics"/> </logger> <root> <priority value="info"/> <appender-ref ref="STDOUT-DEBUG"/> </root> </log4j:configuration>

  Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >