Search Results

Search found 8336 results on 334 pages for 'today'.

Page 313/334 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

• WDS DHCP same server on Windows Server 2008

  - by Richard

  I have been struggling with a problem on my Windows Server 2008 for the past 4 - 5 hours and cannot figure out whats wrong. I have tried pretty much everything that I found on google and all the links are purple. Hopefully you guys can help me. I am running a Windows Server 2008 Standard edition with the latest updates as of today. Furthermore I am running a Windows Server 2003. Both are virtual machines on my ESXi 5 server. My network is: 192.168.10.0/24 W2k8: 192.168.10.251 is the PDC running ADS, DHCP and WDS W2k3: 192.168.10.253 AND 192.168.1.175 running Routing and Remote Access and ISA 2006 Enterprise In my internal network (192.168.10.0/24) I have my client machine (192.168.10.10) that runs a VMWare Workstation. I am trying to deploy Windows 7 Home Premium to a virtual machine on my VMWorkstation via PXE. I have set the Workstation's VM network adapter to "bridged" so that it uses the physical network adapter and is connected to my internal network. The DHCP pool is configured to give IP addresses from 192.168.10.10-192.168.10.15 (works for normal clients and is not used up) When I start my VM with the PXE I get the error: PXE-E52:proxyDHCP offers were received. No DHCP offers were received Apperently this means "that means that WDS responded but the DHCP server did not." People suggested to direct the traffic to both WDS and DHCP on the router, since everything is on the same subnet there is no need for that as the broadcast is seen by everyone (WDS and DHCP) No reservation for the virtual mac addrs is made on the DHCP. Furthermore it was suggested to configure the DHCP options: Option 60= PXEClient Option 66= WDS server name or IP address Option 67= Boot file name However, this is not recommended by Microsoft, I tried it and it did not solve my problem. The configuration on the WDS (My System is German therefore the actual naming might be different): PXE response tab: PXE responses is set to "ALL (known and unknown)" DHCP Tab: Do not listen to port 67 is NOT ticked - if I tick this I do not get any responses and the PXE errors gets PXE-E51 that neither DHCP or proxyDHCP were received DHCP-Option 60 for "PXEClient" is ticked The confusing part here is that it is advised in the tab to tick the first option since it is on the same server. Network Configuration Tab: Use the following IP-Address range for Multicast-IP-Address: 224.0.1.0 - 224.0.10.0 Thats not the default one, however it is in the allowed range. The UDP port range is the default since it is not advised to change them. I tried to change the "networkprofile" from 100mbits/1gbits and custom. I am running a 1gbit network with CAT6 cables and 1gbit netgear switch 5 ports. Everything is configured to use 1gbit. The WDS is authorised for the DHCP server. My ISA 2006 configuration: For the internal networking i have configured the following policy array: Allow protocols on internal network including the w2k3 host: 67,68,53,ICMP, 4011 UDP receive, 64001-6500 UDP send receive, 69 UDP send Routing and Remote Access I tried the DHCP relay agent configuration that was suggested as well, but that did not work I would highly appreciate anykind of help because I am pretty much done here with my nerves. Thank you very much in advance.

  Read the article

• Performance Tuning a High-Load Apache Server

  - by futureal

  I am looking to understand some server performance problems I am seeing with a (for us) heavily loaded web server. The environment is as follows: Debian Lenny (all stable packages + patched to security updates) Apache 2.2.9 PHP 5.2.6 Amazon EC2 large instance The behavior we're seeing is that the web typically feels responsive, but with a slight delay to begin handling a request -- sometimes a fraction of a second, sometimes 2-3 seconds in our peak usage times. The actual load on the server is being reported as very high -- often 10.xx or 20.xx as reported by top. Further, running other things on the server during these times (even vi) is very slow, so the load is definitely up there. Oddly enough Apache remains very responsive, other than that initial delay. We have Apache configured as follows, using prefork: StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 And KeepAlive as: KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 Looking at the server-status page, even at these times of heavy load we are rarely hitting the client cap, usually serving between 80-100 requests and many of those in the keepalive state. That tells me to rule out the initial request slowness as "waiting for a handler" but I may be wrong. Amazon's CloudWatch monitoring tells me that even when our OS is reporting a load of 15, our instance CPU utilization is between 75-80%. Example output from top: top - 15:47:06 up 31 days, 1:38, 8 users, load average: 11.46, 7.10, 6.56 Tasks: 221 total, 28 running, 193 sleeping, 0 stopped, 0 zombie Cpu(s): 66.9%us, 22.1%sy, 0.0%ni, 2.6%id, 3.1%wa, 0.0%hi, 0.7%si, 4.5%st Mem: 7871900k total, 7850624k used, 21276k free, 68728k buffers Swap: 0k total, 0k used, 0k free, 3750664k cached The majority of the processes look like: 24720 www-data 15 0 202m 26m 4412 S 9 0.3 0:02.97 apache2 24530 www-data 15 0 212m 35m 4544 S 7 0.5 0:03.05 apache2 24846 www-data 15 0 209m 33m 4420 S 7 0.4 0:01.03 apache2 24083 www-data 15 0 211m 35m 4484 S 7 0.5 0:07.14 apache2 24615 www-data 15 0 212m 35m 4404 S 7 0.5 0:02.89 apache2 Example output from vmstat at the same time as the above: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 8 0 0 215084 68908 3774864 0 0 154 228 5 7 32 12 42 9 6 21 0 198948 68936 3775740 0 0 676 2363 4022 1047 56 16 9 15 23 0 0 169460 68936 3776356 0 0 432 1372 3762 835 76 21 0 0 23 1 0 140412 68936 3776648 0 0 280 0 3157 827 70 25 0 0 20 1 0 115892 68936 3776792 0 0 188 8 2802 532 68 24 0 0 6 1 0 133368 68936 3777780 0 0 752 71 3501 878 67 29 0 1 0 1 0 146656 68944 3778064 0 0 308 2052 3312 850 38 17 19 24 2 0 0 202104 68952 3778140 0 0 28 90 2617 700 44 13 33 5 9 0 0 188960 68956 3778200 0 0 8 0 2226 475 59 17 6 2 3 0 0 166364 68956 3778252 0 0 0 21 2288 386 65 19 1 0 And finally, output from Apache's server-status: Server uptime: 31 days 2 hours 18 minutes 31 seconds Total accesses: 60102946 - Total Traffic: 974.5 GB CPU Usage: u209.62 s75.19 cu0 cs0 - .0106% CPU load 22.4 requests/sec - 380.3 kB/second - 17.0 kB/request 107 requests currently being processed, 6 idle workers C.KKKW..KWWKKWKW.KKKCKK..KKK.KKKK.KK._WK.K.K.KKKKK.K.R.KK..C.C.K K.C.K..WK_K..KKW_CK.WK..W.KKKWKCKCKW.W_KKKKK.KKWKKKW._KKK.CKK... KK_KWKKKWKCKCWKK.KKKCK.......................................... ................................................................ From my limited experience I draw the following conclusions/questions: We may be allowing far too many KeepAlive requests I do see some time spent waiting for IO in the vmstat although not consistently and not a lot (I think?) so I am not sure this is a big concern or not, I am less experienced with vmstat Also in vmstat, I see in some iterations a number of processes waiting to be served, which is what I am attributing the initial page load delay on our web server to, possibly erroneously We serve a mixture of static content (75% or higher) and script content, and the script content is often fairly processor intensive, so finding the right balance between the two is important; long term we want to move statics elsewhere to optimize both servers but our software is not ready for that today I am happy to provide additional information if anybody has any ideas, the other note is that this is a high-availability production installation so I am wary of making tweak after tweak, and is why I haven't played with things like the KeepAlive value myself yet.

  Read the article

• bind9 DNS Ubuntu names pingible on server, but not on Windows Machines?

  - by leeand00

  I setup a DNS server today on Ubuntu, following this tutorial. My intent was to setup my network for dns-name resolving on the private LAN within a single zone (nothing fancy I just want name resolution). I've tested the setup on the DNS server machine itself, and I can ping all the machines listed in the configuration file. I've also configured the Windows Machines on my network, and for some reason they are incapable of pinging by names as was possible on the DNS Server itself. I've tried running nslookup on the Windows DNS clients and I receive and error mentioning the address of the DNS server. DNS forwarding works fine, I'm not having any trouble accessing the internet, the problem only lies within accessing names within the private LAN. Here are my configuration files: options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { 8.8.8.8; 8.8.8.4; 74.242.0.12; //68.87.76.178; }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.options zone "leerdomain.local" { type master; file "/etc/bind/zones/leerdomain.local.db"; notify no; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.2.168.192.in-addr.arpa"; notify no; }; /etc/bind/named.conf.local Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 2010011001 28800 3600 604800 38400 ); leerdomain.local. IN NS ns.leerdomain.local. ns IN A 192.168.2.9 asus IN A 192.168.2.254 www IN CNAME asus vaio IN A 192.168.2.253 iptouch IN A 192.168.2.252 toshiba IN A 192.168.2.251 gw IN A 192.168.2.1 TXT "Network Gateway" /etc/bind/zones/leerdomain.local.db (Validates fine with named-checkzone when validating zone leerdomain.local) Reverse Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 201001101 28800 604800 604800 86400 ) IN NS ns.leerdomain.local. 1 IN PTR gw.leerdomain.local. 254 IN PTR asus.leerdomain.local. 253 IN PTR vaio.leerdomain.local. 252 IN PTR iptouch.leerdomain.local. 251 IN PTR toshiba.leerdomain.local. /etc/bind/zones/rev.2.168.192.in-addr.arpa *(Does not validate with named-checkzone when validating zone leerdomain.local gives an error of: zone leerdomain.local/IN: NS 'ns.leerdomain.local' has no address records (A or AAAA) zone leerdomain.local/IN: not loaded due to errors. * Despite not validating bind9 starts without errors in /var/log/syslog I've also configured a few of the windows machines on my network to have the static ip as specified in the lookup and reverse lookup config files. i.e. Using nslookup yields the following results: C:\Users\leeand00>nslookup ns Server: UnKnown Address: 192.168.2.9 *** UnKnown can't find ns: Non-existent domain C:\Users\leeand00>nslookup gw Server: UnKnown Address: 192.168.2.9 Name: gw. Additionally trying to ping by name also fails on machines that are not the DNS Server. Is there something wrong with my configuration of either the nameserver or the Windows Boxes that is keeping me from accessing other machines using names?

  Read the article

• TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

  - by ashwalk

  I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

  Read the article

• Windows Server 2012 Migration (DNS/AD DS Standard Eval to Essentials OEM) P2V -> Do I need a Secondary Domain Controller during migration?

  - by Aubrey Robertson

  This is my first post on this exchange (although not my first on stack exchange), so please have patience. I am a 3rd year student intern, and I have been tasked with virtualizing the server systems at the company I work for. I have come a long way, and I am almost ready to install the VM Server in migration mode. Here is some information: Source Server: Windows Server 2012 Standard Evaluation DNS Server (local only) Advanced Directory Domain Services File and Storage stuff A few other server roles Destination Server: Windows Server 2012 Essentials OEM (Hyper-V client) Running under a temporary Hyper-V host (will migrate the Hyper-V host back to the old machine after the original server is virtualized as a client). Sitting currently at the "Select Installation Mode" screen. I have been following the guides on Microsoft tech net, and today I spent most of the day getting rid of issues in the Best Practices Analyser on the source machine. I have 3 remaining issues (which are all related): ERROR: DNS: DNS servers on Ethernet (adapter name) should include the loopback address, but not as the first entry (flavour text indicates that, during migration, the DNS server may not be found) WARNING: All domains should have at least two domain controllers for redundancy. WARNING: DNS: Ethernet should be configured to use both a preferred and an alternate DNS Server. All of these issues can be resolved by deploying a secondary domain controller, but I have never done that before (see my concerns below). The main issue here that I am concerned with for installing in migration mode is the FIRST one (the error). If I try and set-up the new server deployment, and the adapter domain controller is listed as localhost, then this may cause the installation to fail. (at least, this is what the Microsoft documentation suggests). But I do not have another IP address to enter here as I have no other local domain controllers. So I did the first obvious thing that came to my mind, and tried to use Google DNS servers as my alternates. That did not work because they couldn't recognize other computers in the "forest". Now I'm no expert when it comes to DNS, so please forgive my ignorance. This DNS server is concerned only with Active Directory stuffs for the local network. If I go ahead with migration, and it fails, then I will just have to go ahead and install a secondary DNS server I suppose. The problem I have here is that I am limited by the amount of Windows Server keys I have available (I have 2); however, I do have access to a Linux box running Debian Wheezy that I set-up two weeks ago as a Mantis server. I could install Windows Server 2012 as a secondary DNS (I think) in a VM and use that, but then it seems like I will be wasting time, and probably the Windows key too, and if there's another way to do it with Linux that would be much better. Even better still, do I even need a secondary DNS server for migration at all? The hints said that during migration the original machine "might" not be found. Thank you for your time and consideration.

  Read the article

• Did a recent WinXP update break CD/DVD read speeds? SP2/SP3

  - by quack quixote

  I have two systems with fresh installations of Windows XP Pro SP3 (SP3 slipstreamed into the installer; fully updated after install). One's a refurbished 2.4GHz Pentium4 system; the other is a new 1.6GHz Atom330 build. Both have brand-new dual-layer CD/DVD burners (one's a LiteOn IDE, the other an LG SATA). Both take a really looooong time to read a single-layer DVD in Windows with Cygwin tools. Specifically, 40 minutes or more. I burn backup data to single-layer DVD+/-R and use MD5 hashes for data verification (made with the standard md5sum tool in Unix or Cygwin). The hashes are burned to disc with the data files, and I use this command to verify: $ cd /path/to/disc/mountpoint ; time md5sum -c < md5.txt Here's how long that takes to run on a full single-layer DVD+/-R disc: Old system (WinXP SP2, 1.8GHz Athlon 2500+, last summer): ~10 minutes Old system (Ubuntu 9.04, 1.8GHz Athlon 2500+): ~10 minutes Old system (Debian 5, dual 550MHz P3): ~10 minutes New Pentium4 system (running Ubuntu 9.04): ~5 minutes New Pentium4 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes New Atom330 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes Now the weird stuff: Old system (WinXP SP2, 1.8GHz Athlon 2500+, today): ~25 minutes New Pentium4 system (running WinXP SP3, read from Cygwin): ~40-50 minutes (?!!) New Atom330 system (running WinXP SP3, read from Cygwin): ~40 minutes (can do it in ~30 minutes ...if i have another program spin up the drive first) Since both systems will copy files in 6 minutes using Windows Explorer, I know it's not a hardware problem. Windows just never spins up the drive during the Cygwin read, so it stays super-slow the whole time. Other programs like EAC and DVD Decrypter seem to spin up the disc just fine during their processing. DMA is enabled on both systems. (Can confirm in Windows' Device Manager on the Atom330, not on the P4.) Nero's DriveSpeed tool doesn't seem to have any effect. Copy times are comparable from commandline with Windows' xcopy. Copying with Cygwin's cp looks more like the problem state -- it will spin up the drive for a short time, never reaches full speed, and lets it spin back down again for most of the copy. What I need is to get full read speeds from Cygwin. Is this a known issue with SP3 or some other recent Windows update? Any other ideas? Update: More testing; Windows will spin up the drive when data is copied with Windows tools, but not when read in place or copied with Cygwin tools. It doesn't make sense to me that Windows spins up the drive for copying, but not for other reads. Might be more of a Cygwin problem? Update 2: GUI activity is sluggish during the problem state -- during the Cygwin verifies, there's a slight but noticable delay when dragging windows or icons around on the desktop, switching windows, Alt-Tabbing through open applications, opening new windows, etc. It reminds me of the delay when opening a Windows Explorer window on My Computer just after inserting a DVD. I've tried updating Cygwin (from 1.5.x to 1.7.x), but no change in the problem behavior. I've also noticed this issue occurs on WinXP SP2, but it's not exactly the same -- some spin-up occurs, so the read happens in ~25-30 minutes instead of 40+. The SP2 system used to run the verifies in ~10 minutes, and when it first changed (not sure exactly when, maybe in late November or early December 2009) I thought it was dying hardware. This is why I suspect an official update of breaking this functionality; this has worked for years on that SP2 box.

  Read the article

• Expert iptables help needed?

  - by Asad Moeen

  After a detailed analysis, I collected these details. I am under a UDP Flood which is more of application dependent. I run a Game-Server and an attacker is flooding me with "getstatus" query which makes the GameServer respond by making the replies to the query which cause output to the attacker's IP as high as 30mb/s and server lag. Here are the packet details, Packet starts with 4 bytes 0xff and then getstatus. Theoretically, the packet is like "\xff\xff\xff\xffgetstatus " Now that I've tried a lot of iptables variations like state and rate-limiting along side but those didn't work. Rate Limit works good but only when the Server is not started. As soon as the server starts, no iptables rule seems to block it. Anyone else got more solutions? someone asked me to contact the provider and get it done at the Network/Router but that looks very odd and I believe they might not do it since that would also affect other clients. Responding to all those answers, I'd say: Firstly, its a VPS so they can't do it for me. Secondly, I don't care if something is coming in but since its application generated so there has to be a OS level solution to block the outgoing packets. At least the outgoing ones must be stopped. Secondly, its not Ddos since just 400kb/s input generates 30mb/s output from my GameServer. That never happens in a D-dos. Asking the provider/hardware level solution should be used in that case but this one is different. And Yes, Banning his IP stops the flood of outgoing packets but he has many more IP-Addresses as he spoofs his original so I just need something to block him automatically. Even tried a lot of Firewalls but as you know they are just front-ends to iptables so if something doesn't work on iptables, what would the firewalls do? These were the rules I tried, iptables -A INPUT -p udp -m state --state NEW -m recent --set --name DDOS --rsource iptables -A INPUT -p udp -m state --state NEW -m recent --update --seconds 1 --hitcount 5 --name DDOS --rsource -j DROP It works for the attacks on un-used ports but when the server is listening and responding to the incoming queries by the attacker, it never works. Okay Tom.H, your rules were working when I modified them somehow like this: iptables -A INPUT -p udp -m length --length 1:1024 -m recent --set --name XXXX --rsource iptables -A INPUT -p udp -m string --string "xxxxxxxxxx" --algo bm --to 65535 -m recent --update --seconds 1 --hitcount 15 --name XXXX --rsource -j DROP They worked for about 3 days very good where the string "xxxxxxxxx" would be rate-limited, blocked if someone flooded and also didn't affect the clients. But just today, I tried updating the chain to try to remove a previously blocked IP so for that I had to flush the chain and restore this rule ( iptables -X and iptables -F ), some clients were already connected to servers including me. So restoring the rules now would also block some of the clients string completely while some are not affected. So does this mean I need to restart the server or why else would this happen because the last time the rules were working, there was no one connected?

  Read the article

• ls hangs for a certain directory

  - by Jakobud

  There is a particular directory (/var/www), that when I run ls (with or without some options), the command hangs and never completes. There is only about 10-15 files and directories in /var/www. Mostly just text files. Here is some investigative info: [me@server www]$ df . Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_dev-lv_root 50G 19G 29G 40% / [me@server www]$ df -i . Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/vg_dev-lv_root 3.2M 435K 2.8M 14% / find works fine. Also I can type in cd /var/www/ and press TAB before pressing enter and it will successfully tab-completion list of all files/directories in there: [me@server www]$ cd /var/www/ cgi-bin/ create_vhost.sh html/ manual/ phpMyAdmin/ scripts/ usage/ conf/ error/ icons/ mediawiki/ rackspace sqlbuddy/ vhosts/ [me@server www]$ cd /var/www/ I have had to kill my terminal sessions several times because of the ls hanging: [me@server ~]$ ps | grep ls gdm 6215 0.0 0.0 488152 2488 ? S<sl Jan18 0:00 /usr/bin/pulseaudio --start --log-target=syslog root 23269 0.0 0.0 117724 1088 ? D 18:24 0:00 ls -Fh --color=always -l root 23477 0.0 0.0 117724 1088 ? D 18:34 0:00 ls -Fh --color=always -l root 23579 0.0 0.0 115592 820 ? D 18:36 0:00 ls -Fh --color=always root 23634 0.0 0.0 115592 816 ? D 18:38 0:00 ls -Fh --color=always root 23740 0.0 0.0 117724 1088 ? D 18:40 0:00 ls -Fh --color=always -l me 23770 0.0 0.0 103156 816 pts/6 S+ 18:41 0:00 grep ls kill doesn't seem to have any affect on the processes, even as sudo. What else should I do to investigate this problem? It just randomly started happening today. UPDATE dmesg is a big list of things, mostly related to an external USB HDD that I've mounted too many times and the max mount count has been reached, but that is an un-related problem I think. Near the bottom of dmesg I'm seeing this: INFO: task ls:23579 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. ls D ffff88041fc230c0 0 23579 23505 0x00000080 ffff8801688a1bb8 0000000000000086 0000000000000000 ffffffff8119d279 ffff880406d0ea20 ffff88007e2c2268 ffff880071fe80c8 00000003ae82967a ffff880407169ad8 ffff8801688a1fd8 0000000000010518 ffff880407169ad8 Call Trace: [<ffffffff8119d279>] ? __find_get_block+0xa9/0x200 [<ffffffff814c97ae>] __mutex_lock_slowpath+0x13e/0x180 [<ffffffff814c964b>] mutex_lock+0x2b/0x50 [<ffffffff8117a4d3>] do_lookup+0xd3/0x220 [<ffffffff8117b145>] __link_path_walk+0x6f5/0x1040 [<ffffffff8117a47d>] ? do_lookup+0x7d/0x220 [<ffffffff8117bd1a>] path_walk+0x6a/0xe0 [<ffffffff8117beeb>] do_path_lookup+0x5b/0xa0 [<ffffffff8117cb57>] user_path_at+0x57/0xa0 [<ffffffff81178986>] ? generic_readlink+0x76/0xc0 [<ffffffff8117cb62>] ? user_path_at+0x62/0xa0 [<ffffffff81171d3c>] vfs_fstatat+0x3c/0x80 [<ffffffff81258ae5>] ? _atomic_dec_and_lock+0x55/0x80 [<ffffffff81171eab>] vfs_stat+0x1b/0x20 [<ffffffff81171ed4>] sys_newstat+0x24/0x50 [<ffffffff810d40a2>] ? audit_syscall_entry+0x272/0x2a0 [<ffffffff81013172>] system_call_fastpath+0x16/0x1b And also, strace ls /var/www/ spits out a whole BUNCH of information. I don't know what is useful here... The last handful of lines: ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig icanon echo ...}) = 0 ioctl(1, TIOCGWINSZ, {ws_row=68, ws_col=145, ws_xpixel=0, ws_ypixel=0}) = 0 stat("/var/www/", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 open("/var/www/", O_RDONLY|O_NONBLOCK|O_DIRECTORY|O_CLOEXEC) = 3 fcntl(3, F_GETFD) = 0x1 (flags FD_CLOEXEC) getdents(3, /* 16 entries */, 32768) = 488 getdents(3, /* 0 entries */, 32768) = 0 close(3) = 0 fstat(1, {st_mode=S_IFCHR|0620, st_rdev=makedev(136, 9), ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f3093b18000 write(1, "cgi-bin conf create_vhost.sh\te"..., 125cgi-bin conf create_vhost.sh error html icons manual mediawiki phpMyAdmin rackspace scripts sqlbuddy usage vhosts ) = 125 close(1) = 0 munmap(0x7f3093b18000, 4096) = 0 close(2) = 0 exit_group(0) = ?

  Read the article

• Can't sync filesystem without reboot

  - by Fabio

  I'm having an issue with a linux server. Once a week the running mysql instance hangs and there is no way to fully stop it. If I kill it, it remains in zombie status and init does not reap its pid. The server is used for staging deployments and some internal tools, so it's not under heavy load. The only process constantly used id mysql and for this I think that it's the only process which suffer of this issue. I've searched system logs for errors and the only thing I found is this error (repeated a couple of times) in dmesg output: [706560.640085] INFO: task mysqld:31965 blocked for more than 120 seconds. [706560.640198] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [706560.640312] mysqld D ffff88032fd93f40 0 31965 1 0x00000000 [706560.640317] ffff880242a27d18 0000000000000086 ffff88031a50dd00 ffff880242a27fd8 [706560.640321] ffff880242a27fd8 ffff880242a27fd8 ffff88031e549740 ffff88031a50dd00 [706560.640325] ffff88031a50dd00 ffff88032fd947f8 0000000000000002 ffffffff8112f250 [706560.640328] Call Trace: [706560.640338] [<ffffffff8112f250>] ? __lock_page+0x70/0x70 [706560.640344] [<ffffffff816cb1b9>] schedule+0x29/0x70 [706560.640347] [<ffffffff816cb28f>] io_schedule+0x8f/0xd0 [706560.640350] [<ffffffff8112f25e>] sleep_on_page+0xe/0x20 [706560.640353] [<ffffffff816c9900>] __wait_on_bit+0x60/0x90 [706560.640356] [<ffffffff8112f390>] wait_on_page_bit+0x80/0x90 [706560.640360] [<ffffffff8107dce0>] ? autoremove_wake_function+0x40/0x40 [706560.640363] [<ffffffff8112f891>] filemap_fdatawait_range+0x101/0x190 [706560.640366] [<ffffffff81130975>] filemap_write_and_wait_range+0x65/0x70 [706560.640371] [<ffffffff8122e441>] ext4_sync_file+0x71/0x320 [706560.640376] [<ffffffff811c3e6d>] do_fsync+0x5d/0x90 [706560.640379] [<ffffffff811c40d0>] sys_fsync+0x10/0x20 [706560.640383] [<ffffffff816d495d>] system_call_fastpath+0x1a/0x1f When this happens the only way to make everything working again is a full reboot, but in order to do that I'm forced to use this command after I've manually stopped all running processes echo b > /proc/sysrq-trigger otherwise normal reboot process hangs forever. I've tracked reboots script and I've found out that also the reboot process hangs on a sync call, this one in /etc/init.d/sendsigs (I'm on ubuntu) # Flush the kernel I/O buffer before we start to kill # processes, to make sure the IO of already stopped services to # not slow down the remaining processes to a point where they # are accidentily killed with SIGKILL because they did not # manage to shut down in time. sync I'm almost sure that the cause of this is an hardware issue (the RAID controller???) also because I've other two machines with the same hardware and software configuration and they don't suffer of this, but I can't find any hint in syslog or dmesg. I've also installed smartmontools and mcelog packages but none of them did report any issue. What can I do to track the cause of this issue? Today is happened again, here is the status of system after triggering a reboot init---console-kit-dae---64*[{console-kit-dae}] +-dbus-daemon +-mcelog +-mysqld---{mysqld} +-newrelic-daemon---newrelic-daemon---11*[{newrelic-daemon}] +-ntpd +-polkitd---{polkitd} +-python3 +-rpc.idmapd +-rpc.statd +-rpcbind +-sh---rc---S20sendsigs---sync +-smartd +-snmpd +-sshd---sshd---zsh---sudo---zsh---pstree +-sshd---sshd---zsh---sudo---zsh And here is the status of sync process # ps aux | grep sync root 3637 0.1 0.0 4352 372 ? D 05:53 0:00 sync i.e. Uninterruptible sleep... Hardware specs as reported by lshw I think the raid controller is a fake raid. I usually don't deal with hardware (and for the record I don't have physical access to it) description: Computer product: X7DBP () vendor: Supermicro version: 0123456789 serial: 0123456789 width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=53D19F64-D663-A017-8922-0030487C1FEE *-core description: Motherboard product: X7DBP vendor: Supermicro physical id: 0 version: PCB Version serial: 0123456789 *-firmware description: BIOS vendor: Phoenix Technologies LTD physical id: 0 version: 6.00 date: 05/29/2007 size: 106KiB capacity: 960KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect edd int13floppy2880 acpi usb ls120boot zipboot biosbootspecification *-storage description: RAID bus controller product: 631xESB/632xESB SATA RAID Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 09 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list configuration: driver=ahci latency=0 resources: irq:19 ioport:18a0(size=8) ioport:1874(size=4) ioport:1878(size=8) ioport:1870(size=4) ioport:1880(size=32) memory:d8500400-d85007ff

  Read the article

• Computer makes hissing noise, turns off after few seconds

  - by Kaustubh P

  I have a problem similar to the questions posted here and here. This is my config: Asus M3N78-EM, with AMD Phenom X3 720 2800 Black Edition, 4GB Transcend DDR2 RAM, Nvidia 9400GT. HD is a 160 GB IDE, and a LG IDE DVD-ROM. The power button is a bit off, I have removed the cover of the switch, and the only way it turns on is just giving the "stick" under the cover a gentle press. It turns on sometimes, and at other times, I have to cut-off the power from the PSU, and try again. I will describe my problem in as detail as possible, please bear with me: The problem has started in the last week, a few months after I changed the to the powerswitch arrangement as described above. The PC makes a hissing noise, and I wasn't able to pin-point the noise source, because of the various other fans. At first, removing the HD, rebooting w/o the HD, turning it off, reconnecting and booting made the problem go away. But of late, it doesn't happen. As suggested in the other questions, I tried reducing the load by disconnecting both the IDE drives, and the problem (noise + turn-off) still occurs. I also connected another 80G IDE HD,today morning, adn it still made that noise, and turned off. I also opened up the PSU, but I couldn't see any fault in that, I tried rotating the fan by blowing into the blades, and with my fingers, but the hissing noise didn't come from there. Or maybe the speed wasn't enough to evoke that noise. A few weeks ago: I had cleaned the Cabinet and had repasted the processor and its fan using some thermal paste. Could that be at fault? I also used a vacuum to blow the dust out of the PSU, could the power have been too much, to maybe offset the fan or something? A label on the PSU says it uses a ball-bearing fan. That only leaves me with the Processor fan and the processor itself. I didn't try removing the processor fan and processor from the motherboard, and then turning the PC on, fearing damage. Will doing so cause any damage? What can I do to localize and pin-point the problem? Also, after a few tries, the Computer starts up. Sometimes it turns of within 2 seconds, sometimes after the POST. Once it turned off at the grub. Another time it booted completely and then turned off. The only way to ensure that the PC wont turn off, is if the hissing noise stops. EDIT: I suspect it to be the Processor/Processor fan, owing to the source of noise. All the config, except for the Cabinet, is just over a year old. EDIT2: I also just remembered, that I had set the "On-power resume" to turn on, i.e. If I supply he PC with power, it will turn itself on, w/o me needing to press the switch. I had done that to workaround the faulty power-switch, as noted above. EDIT3: I calculated the power my system needs, from the antec site, and I just arrived at 292W

  Read the article

• Backup a hosted Sharepoint

  - by David Mackintosh

  One of my customers has outsourced their Sharepoint and Exchange services to a hosted services provider. I believe it is a Sharepoint 2007 service. It is a shared hosting solution, so we do not have any kind of access to the server itself; we only have user-level and sharepoint-administrator-level access to the Sharepoint application. They have come to the point where they would like to have a copy of everything that is on the Sharepoint server. I have downloaded the Office Sharepoint Designer 2007, and it features three (!) ways to backup a Sharepoint server, none (!) of which work for me: File-Export-Personal Web Package: When selecting everything, it calculates a negative size. Barfs with No "content-type" in CGI environment error. File-Export-Sharepoint Template: barfs with a A World Wide Web browser, such as Windows Internet Explorer, is required to use this feature error. Site-Administration-Backup Web Site: wants to create the backup .cmp file on the sharepoint server itself. I don't have access to any servers on the same network so I can't redirect it to any form of the suggested \\server\place. Barfs with a The Web application at $URL could not be found. [...] error. Possibly moot because Google tells me that bad things happen using OSD to back up sites larger than 24MB (which this site is most definitely). So I called the helpdesk of the outsource provider, and got told that they recommend using OSD, but no they don't actually provide any application support for OSD (not that I blame them for that), but they could do a stsadm.exe backup and provide us with that, and OSD should be able to read the resulting cmp file. Then for authorization reasons they had my customer call them directly (since I can't authorize such an operation), and they told him that he didn't want a stsadm.exe backup, he wanted to get into an 'explorer view' and deal with things that way (they were vague). Google hasn't been much help in figuring out what an 'explorer view' is, let alone how I bring one up. The end goal of this operation is to have a backup of the site as it exists (hopefully today, but shortly anyways) in such a format that we don't need another sharepoint server to restore it to. Ie we'd like to be able to pick individual content directly out of this backup. We are not excessively concerned with things like formatting. We just want the documents. This is a fairly complex site with multiple subsites and multiple folders per subsite, so sitting there and manually downloading each file isn't really going to happen if there is a better easier way. So, my questions: Is the stsadm.exe backup what I want? If not, what do I want? If I manage to convince them that I do want the stsadm.exe backup, can I pick files out of the resulting backup file with OSD? If OSD isn't going to let me extract individual files, is there a tool I can use that can?

  Read the article

• Performance of Cluster Shared Volume file copy from SAN

  - by Sequenzia

  I am hoping someone can help me out with a strange issue. We are running a Microsoft Failover Cluster with Server 2008 R2 and an Equallogic PS4000 SAN. Our main configuration has 2 Dell Poweredge T710 Servers in the cluster. We have CSV and Quorm setup. The servers each have 10 Broadcom 1Gb NICs. Right now 4 of the NICS are on the iSCSI network for accessing the SAN. They use MPIO and the Dell HIT pack. We have 5 VMs running on each node and everything runs smooth. No noticeable performance issues or anything. From the SAN I can see the 4 iSCSI connections from each server to each volume (CSV and Quorm). Again, it seems to perform great. The problem I am running into is with backups. I have tried a few backup programs like backupchain and Veeam. The problem is both of them are very very slow to backup the VMs. For instance I have a 500GB (fixed disc) VHD that’s running on the cluster. It takes over 18 hours to backup that VHD and that’s with compression and depuping turned off which is supposed to be the fasted. We also have a separate server that is just for backups. It has a lot of directed attached storage. As part of the troubleshooting I decided to bring that server into the cluster as a node. It now has access to the CSV and can read from C:\clusterstorage\volume1 which is where our VHDs live. This backup server only has 2 NICs. 1 NIC is going to the iSCSI network and the other is just on the main network. It has Intel NICS in it without any sort of MPIO or teaming. So with the 3rd server now in the cluster I started doing some benchmarking. I have a test VHD that’s about 7GBs that’s stored in the CSV. I have tested file copying that VHD from all 3 servers to directed attached storage in the respective server. The 2 Dell servers that are the main nodes in the cluster (they house the VMs) are reading that file at about 20Mbs/Sec. Which at that rate is way to slow for the backups. The other server which only has 1 NIC to the SAN is reading at around 100Mbs/Sec. I spent a few hours on the phone with Dell today about this . We went through all kind of tests and he was pretty dumb founded. He really has no idea why that server with only 1 NIC is reading about 5 times as fast as the servers with 4 NICS and MPIO. We looked at the network utilization of the NICs while the file copy was going on. The servers with the 4 NICs had a small increase of activity during the file copy but they only went up to around 8-10% on all 4 NICs. The other server with the 1 NIC jumped up to over 80% during the file copy. I plan on doing some more testing after hours and calling Dell back tomorrow but I really am confused (and so is Dell’s support rep) why I cannot get faster file copy access to the CSV on those servers. Anyone have any input on this? Any feedback would be greatly appreciated. Thanks in advance.

  Read the article

• "Possible SYN flooding" in log despite low number of SYN_RECV connections

  - by al4

  Recently we had an apache server which was responding very slowly due to SYN flooding. The workaround for this was to enable tcp_syncookies (net.ipv4.tcp_syncookies=1 in /etc/sysctl.conf). I posted a question about this here if you want more background. After enabling syncookies we started seeing the following message in /var/log/messages approximately every 60 seconds: [84440.731929] possible SYN flooding on port 80. Sending cookies. Vinko Vrsalovic informed me that this means the syn backlog is getting full, so I raised tcp_max_syn_backlog to 4096. At some point I also lowered tcp_synack_retries to 3 (down from the default of 5) by issuing sysctl -w net.ipv4.tcp_synack_retries=3. After doing this, the frequency seemed to drop, with the interval of the messages varying between roughly 60 and 180 seconds. Next I issued sysctl -w net.ipv4.tcp_max_syn_backlog=65536, but am still getting the message in the log. Throughout all this I've been watching the number of connections in SYN_RECV state (by running watch --interval=5 'netstat -tuna |grep "SYN_RECV"|wc -l'), and it never goes higher than about 240, much much lower than the size of the backlog. Yet I have a Red Hat server which hovers around 512 (limit on this server is the default of 1024). Are there any other tcp settings which would limit the size of the backlog or am I barking up the wrong tree? Should the number of SYN_RECV connections in netstat -tuna correlate to the size of the backlog? Update As best I can tell I'm dealing with legitimate connections here, netstat -tuna|wc -l hovers around 5000. I've been researching this today and found this post from a last.fm employee, which has been rather useful. I've also discovered that the tcp_max_syn_backlog has no effect when syncookies are enabled (as per this link) So as a next step I set the following in sysctl.conf: net.ipv4.tcp_syn_retries = 3 # default=5 net.ipv4.tcp_synack_retries = 3 # default=5 net.ipv4.tcp_max_syn_backlog = 65536 # default=1024 net.core.wmem_max = 8388608 # default=124928 net.core.rmem_max = 8388608 # default=131071 net.core.somaxconn = 512 # default = 128 net.core.optmem_max = 81920 # default = 20480 I then setup my response time test, ran sysctl -p and disabled syncookies by sysctl -w net.ipv4.tcp_syncookies=0. After doing this the number of connections in the SYN_RECV state still remained around 220-250, but connections were starting to delay again. Once I noticed these delays I re-enabled syncookies and the delays stopped. I believe what I was seeing was still an improvement from the initial state, however some requests were still delayed which is much worse than having syncookies enabled. So it looks like I'm stuck with them enabled until we can get some more servers online to cope with the load. Even then, I'm not sure I see a valid reason to disable them again as they're only sent (apparently) when the server's buffers get full. But the syn backlog doesn't appear to be full with only ~250 connections in the SYN_RECV state! Is it possible that the SYN flooding message is a red herring and it's something other than the syn_backlog that's filling up? If anyone has any other tuning options I haven't tried yet I'd be more than happy to try them out, but I'm starting to wonder if the syn_backlog setting isn't being applied properly for some reason.

  Read the article

• Inconsistent file downloads of (what should be) the same file

  - by Austin A.

  I'm working on a system that archives large collections of timetstamped images. Part of the system deals with saving an image to a growing .zip file. This morning I noticed that the log system said that an image was successfully downloaded and placed in the zip file, but when I downloaded the .zip (from an apache alias running on our server), the images didn't match the log. For example, although the log said that camera 3484 captured on January 17, 2011, when I download from the apache alias, the downloaded zip file only contains images up to January 14. So, I sshed onto the server, and unzipped the file in its own directory, and that zip file has images from January 14 to today (January 17). What strikes me as odd is that this should be the exact same file as the one I downloaded from the apache alias. Other experiments: I scp-ed the file from the server to my local machine, and the zip file has the newer images. But when I use an SCP client (in this case, Fugu for OSX), I get the zip file for the older images. In short: unzipping a file on the server or after downloading through scp or after downloading through wget gives one zip file, but unzipping a file from Chrome, Firefox, or SCP client gives a different zip file, when they should be exactly the same. Unzipping on the server... [user@server ~]$ cd /export1/amos/images/2011/84/3484/00003484/ [user@server 00003484]$ ls -la total 6180 drwxr-sr-x 2 user groupname 24 Jan 17 11:20 . drwxr-sr-x 4 user groupname 36 Jan 11 19:58 .. -rw-r--r-- 1 user groupname 6309980 Jan 17 12:05 2011.01.zip [user@server 00003484]$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg extracting: 20110114_143554.jpg replace 20110114_143554.jpg? [y]es, [n]o, [A]ll, [N]one, [r]ename: y extracting: 20110114_143554.jpg extracting: 20110114_153458.jpg (...bunch of files...) extracting: 20110117_170459.jpg extracting: 20110117_173458.jpg extracting: 20110117_180501.jpg Using the wget through apache alias. local:~ user$ wget http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip --12:38:13-- http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip => `2011.01.zip' Resolving example.com... ip.ip.ip.ip Connecting to example.com|ip.ip.ip.ip|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 6,327,747 (6.0M) [application/zip] 100% [=====================================================================================================>] 6,327,747 1.03M/s ETA 00:00 12:38:56 (143.23 KB/s) - `2011.01.zip' saved [6327747/6327747] local:~ user$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg (... same as before...) extracting: 20110117_183459.jpg Using scp to grab the zip local:~ user$ scp user@server:/export1/amos/images/2011/84/3484/00003484/2011.01.zip . 2011.01.zip 100% 6179KB 475.3KB/s 00:13 local:~ user$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg (...same as before...) extracting: 20110117_183459.jpg Using Fugu to download 2011.01.zip from /export1/amos/images/2011/84/3484/00003484/ gives images 20110113_090457.jpg through 201100114_010554.jpg Using Firefox to download 2011.01.zip from http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip gives images 20110113_090457.jpg through 201100114_010554.jpg Using Chrome gives same results as Firefox. Relevant section from apache httpd.conf: # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the realname directory are treated as applications and # run by the server when requested rather than as documents sent to the client. # The same rules about trailing "/" apply to ScriptAlias directives as to # Alias. # ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" Alias /zipfiles/ /export1/amos/images/

  Read the article

• Cannot open simple script application on mac

  - by streetpc

  Mac OS X 10.6 I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: Is there some kind of validity caching for applications ? based on what ? how do I flush it ? Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

  Read the article

• Can not access network computers anymore

  - by Johny Skovdal

  Last Thursday (03/05/12) I got a new computer to be able to work from home. I plugged it, by cable, into the company network and installed most of the software needed for me to do so, by accessing a share on my stationary computer at work. I had no issues here what so ever, and everything just worked. Yesterday evening I tried accessing the company network trough Windows VPN, and while I was able to connect to the network, I was unable to connect to any computers on the network. I did, however, get an error when connecting, but I can't seem to get the error again, to get the details of the error message. Today I am sitting on the company network again, and now I can not access anything on the network like I could last Thursday, though I can ping all the computers I am attempting to access. Here is a list of details that might help in troubleshooting this issue (updated): List of observations / actions My computer is identical to another computer that has no issues. It is not on the domain but rather on the default workgroup, but this was not an issue last Thursday, so I am assuming it still is not. I am able to access my e-mail on the exchange server. I can connect to our TFS server from Visual Studio but not from Explorer. I can also connect to Database Servers and Remote Desktop. I can see several computers when browsing network computers, but I am unable to connect to any of them. When trying to connect to a computer I am consistently met with the error code "0x80070035" (network path not found). I also get the 0x80070035 error when double clicking the target computer from the Network UI. I am not met with a login dialog when trying to access a computer, as I should, since I am not on the domain. (I did login to both Exchange, Remote Desktop and TFS though) Between Thursday where it worked and Sunday evening where it did not, I have installed quite a few security updates, plus various tools etc. that I need for programming. I have tried accessing by computer name and ip and neither of them work. I can ping by computer name. I have deleted all (1 entry) stored network credentials. I am able to access my computer from the target computer. Client and Server can see each other on the network = Network Discovery is enabled. I am using the network profile "Work". When accessing the network through VPN, I am unable to get anything to work using computernames, but all of the above applies when using IP adresses instead of computername. I run Windows 7 Home Premium on my computer. Using powershell attempting to access a share I get the following error (ComputerName and ShareName being correct values of course): PS C:\Users\MyUser> cd \\ComputerName\ShareName Set-Location : Cannot find path '\\ComputerName\ShareName' because it does not exist. At line:1 char:3 + cd <<<< \\ComputerName\ShareName + CategoryInfo : ObjectNotFound: (\\ComputerName\ShareName:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand However, ping'ing the same machine (ping ComputerName) from powershell I get response immediately. (As mentioned in the list of observations/actions, I tried the above with the IP address again on VPN, to get the same result) Conclusion So to sum up, pretty much the only thing I can not do, is access the other computers through browsing (explorer.exe, powershell, map networkdrive, etc.), which means that I am pretty much down to, that it is unable to resolve the path somehow, when trying to connect to other computers trough browsing, though the path gets resolved perfectly using all kinds of other services. Any recommendations as to what I can try next to resolve the issue? :)

  Read the article

• Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

  - by icelava

  I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

  Read the article

• How can I check if PHP was compiled with the UNICODE version of the Win32 API?

  - by Wesley Murch

  This is related to this Stack Overflow post: glob() can't find file names with multibyte characters on Windows? I'm having issues with PHP and files that have multibyte characters on Windows. Here's my test case: print_r(scandir('./uploads/')); print_r(glob('./uploads/*')); Correct Output on remote UNIX server: Array ( [0] => . [1] => .. [2] => filename-äöü.jpg [3] => filename.jpg [4] => test?test.jpg [5] => ??? ?????.jpg [6] => ?????????.jpg [7] => ???.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg [2] => ./uploads/test?test.jpg [3] => ./uploads/??? ?????.jpg [4] => ./uploads/?????????.jpg [5] => ./uploads/???.jpg ) Incorrect Output locally on Windows: Array ( [0] => . [1] => .. [2] => ??? ?????.jpg [3] => ???.jpg [4] => ?????????.jpg [5] => filename-äöü.jpg [6] => filename.jpg [7] => test?test.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg ) Here's a relevant excerpt from the answer I chose to accept (which actually is a quote from an article that was posted online over 2 years ago): From the comments on this article: http://www.rooftopsolutions.nl/blog/filesystem-encoding-and-php The output from your PHP installation on Windows is easy to explain : you installed the wrong version of PHP, and used a version not compiled to use the Unicode version of the Win32 API. For this reason, the filesystem calls used by PHP will use the legacy "ANSI" API and so the C/C++ libraries linked with this version of PHP will first try to convert yout UTF-8-encoded PHP string into the local "ANSI" codepage selected in the running environment (see the CHCP command before starting PHP from a command line window) Your version of Windows is MOST PROBABLY NOT responsible of this weird thing. Actually, this is YOUR version of PHP which is not compiled correctly, and that uses the legacy ANSI version of the Win32 API (for compatibility with the legacy 16-bit versions of Windows 95/98 whose filesystem support in the kernel actually had no direct support for Unicode, but used an internal conversion layer to convert Unicode to the local ANSI codepage before using the actual ANSI version of the API). Recompile PHP using the compiler option to use the UNICODE version of the Win32 API (which should be the default today, and anyway always the default for PHP installed on a server that will NEVER be Windows 95 or Windows 98...) I can't confirm whether this is my problem or not. I used phpinfo() and did not find anything interesting, but I wasn't sure what to look for. I've been using XAMPP for easy installations, so I'm really not sure exactly how it was installed. I'm using Windows 7, 64 bit - so forgive my ignorance, but I'm not even sure if "Win32" is relevant here. How can I check if my current version of PHP was compiled with the configuration mentioned above? PHP Version: 5.3.8 System: Windows NT WES-PC 6.1 build 7601 (Windows 7 Home Premium Edition Service Pack 1) i586 Build Date: Aug 23 2011 11:47:20 Compiler: MSVC9 (Visual C++ 2008) Architecture: x86 Configure Command: cscript /nologo configure.js "--enable-snapshot-build" "--disable-isapi" "--enable-debug-pack" "--disable-isapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=D:\php-sdk\oracle\instantclient11\sdk,shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze"

  Read the article

• Cannot open simplest mac application

  - by streetpc

  I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: * Is there some kind of validity caching for applications ? based on what ? how do I flush it ? * Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

  Read the article

• BSOD Code 16, artifacts all over the place (gtx 260)

  - by belinea

  I have a following, quite dated rig E8400 Core 2 Duo cpu Intel Dragontail Peak DP35DP motherboard on Intel Bearlake P35 chipset 4GB ram Geforce 260gtx Corsair 650W PSU Windows 7 64 bit The following things has happened in the last few days. I first decided to update my Nvidia drivers to the latest version. That was 4 days ago. PC worked fine for 2 days and I was able to play few games as well without any problems. Then 2 days ago a first crash happened while playing the new XCOM game. BSOD code 16. Just the blue screen, no artifacts. PC rebooted and worked well again, I continued playing this game for another 2 hours and went to sleep. Next evening I tried to play some BF3 multiplayer (use to play on LOW settings). Approx. 10 minutes into the game red/pink-ish artifacts appeared on the screen and game quit to desktop. Restarted the game and another 3-4 minutes afterwards another crash to desktop but this time followed shortly by BSOD Code 16. From that moment I started to seeing artifacts on random startups, including Windows loading screen and the BIOS itself. Windows would still load but soon enough it would BSOD on a simple task like opening a Internet browser. Today I get tons of artifacts (little small red dashes all over the screen) on BIOS, loading screen, normal Windows mode as well as safe mode. I suspect it wouldn't be drivers but I tried removing and sweeping them entirely in the safe mode. PC would still start with artifacts all over the place but would load the normal mode, just without the driver, in the default lowest resolution. As soon as proper Nvidia drivers are installed though and PC rebooted, Windows doesn't load at all as BSOD now appears on loading screen. However, again, if I go to safe mode and remove drivers, normal mode launches fine. So obviously crash happens only on high resolution. I opened my machine this morning and gave it a proper cleaning even though it wasn't heavily dusted. It didn't help and number of artifacts seems to increase with every PC restart. I write these words in safe mode, which works, but I have to look through all the red dots and dashes. I don't have built in GPU chipset so I can't try removing my Geforce card nor can I borrow A GPU from anyone else. What are my options? I was looking into getting a completely new rig around Christmas so I'm not freaking out about this. If everything points to hardware issue I may simply decide to get the new machine earlier and don't bother with fixing this one. However it would be great to learn more if this is indeed situation that has slim chances of getting sorted. I realize BSOD Code 16 is rather popular topic online but every story seems a bit different and there can be number of issues with it. Hence a new thread.

  Read the article

• Clarification On Write-Caching Policy, Its Underlying Options And How It Applies To Hard Drives And Solid-State Drives

  - by Boris_yo

  In last week after doing more research on subject matter, I have been wondering about what I have been neglecting all those years to understand write-caching policy, always leaving it on default setting. Write-caching policy improves writing performance and consists of write-back caching and write-cache buffer flushing. This is how I understand all the above, but correct me if I erred somewhere: Write-through cache / Write-through caching itself is not a part of write caching policy per se and it's when data is written to both cache and storage device so if Windows will need that data later again, it is retrieved from cache and not from storage device which means only improved read performance as there is no need for waiting for storage device to read required data again. Since data is still written to storage device, write performance isn't improved and represents no risk of data loss or corruption in case of power failure or system crash while only data in cache gets lost. This option seems to be enabled by default and is recommended for removable devices with no need to use function of "Safely Remove Hardware" on user's part. Write-back caching is similar to above but without writing data to storage device, periodically releasing data from cache and writing to storage device when it is idle. In my opinion this option improves both read and write performance but represents risk if power failure or system crash occurs with the outcome of not only losing data eventually to be written to storage device, but causing file inconsistencies or corrupted file system. Write-back caching cannot be enabled together with write-through caching and it is not recommended to be enabled if no backup power supply is availabe. Write-cache buffer flushing I reckon is similar to write-back caching but enables immediate release and writing of data from cache to storage device right before power outage occurs but I don't know if it applies also to occasional system crash. This option seem to be complementary to write-back cache reducing or potentially eliminating risk of data loss or corruption of file system. I have questions about relevance of last 2 options to today's modern SSDs in order to get best performance and with less wear on SSDs: I know that traditional hard drives come with onboard cache (I wonder what type of cache that is), but do SSDs also come with cache? Assuming they do, is this cache faster than their NAND flash and system RAM and worth taking the risk of utilizing it by enabling write-back cache? I read somewhere that generally storage device's cache is faster than RAM, but I want to be sure. Additionally I read that write-caching should be enabled since current data that is to be written later to NAND flash is kept for a while in cache and provided there is data that gets modified a lot before finally being written, holding of this data and its periodic release reduces its write times to SSD thereby reducing its wearing. Now regarding to write-cache buffer flushing, I heard that SSD controllers are so fast by themselves that enabling this option is not required, because they manage flushing. However, once again, I don't know if SSDs have their own onboard cache and whether or not it is faster than their NAND flash and system RAM because if it is, keeping this option enabled would make sense. Recently I have posted question about issue with my Intel 330 SSD 120GB which was main reason to do deeper research having suspicion of write-caching policy being the culprit of SSD's freezing issue assuming data being released is what causes freezes. Currently I have write-cache enabled and write-cache buffer flushing disabled because I believe SSD controller's management of write-cache flushing and Windows write-cache buffer flushing are conflicting with each other: Since I want to troubleshoot in small steps to finally determine the source of issue, I have decided to start with write-caching policy and the move to drivers, switching to AHCI later on and finally disabling DIPM (device initiated power management) through registry modification thanks to @TomWijsman

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• AMD Catalyst 13.9 installation failure

  - by Simon Verbeke

  Earlier today I installed Windows 8.1, and when I wanted to go into Catalyst Control Center, I noticed some odd error of CCC not being able to display options. I then figured I needed a driver update, so I downloaded the latest drivers, version 13.9, and tried to install them. While it was trying to install the display drivers, I got a blue screen. Tried again and got the same. Then I used an uninstall tool from AMD to remove all traces of my old drivers and tried to install the new drivers. Again, a blue screen. This is all I could think of to try. Would anyone know some other things I can try? EDIT: thought I might want to include the log entry for the crash: - <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> - <System> <Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" /> <EventID Qualifiers="16384">1001</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-10-19T20:59:25.000000000Z" /> <EventRecordID>26587</EventRecordID> <Correlation /> <Execution ProcessID="0" ThreadID="0" /> <Channel>System</Channel> <Computer>Simon-PC</Computer> <Security /> </System> - <EventData> <Data Name="param1">0x0000007e (0xffffffffc0000005, 0xfffff80002a86dca, 0xffffd00025f250e8, 0xffffd00025f248f0)</Data> <Data Name="param2">C:\WINDOWS\MEMORY.DMP</Data> <Data Name="param3">101913-8953-01</Data> </EventData> </Event> Another edit: As it turns out, the graphics card isn't showing up any more in the device manager. But as far as I can tell, it is still working (the fans are spinning and my screen is plugged into that graphics card). This is solved. it appears that my graphics card is now running with a default windows driver. I also tried the forced method mentioned here: AMD Graphics Drivers won't install properly . But I still get a BSOD. Third edit: Slight succes! Managed to install version 13.4. Everything appears to be working fine now. I think I'm just going to skip version 13.9.

  Read the article

• Cannot open simplest script mac application

  - by streetpc

  I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: Is there some kind of validity caching for applications ? based on what ? how do I flush it ? Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

  Read the article

• linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

  - by devicerandom

  We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

  Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >