Search Results

Search found 15248 results on 610 pages for 'slashdot configuration'.

Page 316/610 | < Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >

  • Cisco PIX 8.0.4, static address mapping not working?

    - by Bill
    upgrading a working Pix running 5.3.1 to 8.0.4. The memory/IOS upgrade went fine, but the 8.0.4 configuration is not quite working 100%. The 5.3.1 config on which it was based is working fine. Basically, I have three networks (inside, outside, dmz) with some addresses on the dmz statically mapped to outside addresses. The problem seems to be that those addresses can't send or receive traffic from the outside (Internet.) Stuff on the DMZ that does not have a static mapping seems to work fine. So, basically: Inside - outside: works Inside - DMZ: works DMZ - inside: works, where the rules allow it DMZ (non-static) - outside: works But: DMZ (static) - outside: fails Outside - DMZ: fails (So, say, udp 1194 traffic to .102, http to .104) I suspect there's something I'm missing with the nat/global section of the config, but can't for the life of me figure out what. Help, anyone? The complete configuration is below. Thanks for any thoughts! ! PIX Version 8.0(4) ! hostname firewall domain-name asasdkpaskdspakdpoak.com enable password xxxxxxxx encrypted passwd xxxxxxxx encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address XX.XX.XX.100 255.255.255.224 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.68.1 255.255.255.0 ! interface Ethernet2 nameif dmz security-level 10 ip address 192.168.69.1 255.255.255.0 ! boot system flash:/image.bin ftp mode passive dns server-group DefaultDNS domain-name asasdkpaskdspakdpoak.com access-list acl_out extended permit udp any host XX.XX.XX.102 eq 1194 access-list acl_out extended permit tcp any host XX.XX.XX.104 eq www access-list acl_dmz extended permit tcp host 192.168.69.10 host 192.168.68.17 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq 5901 access-list acl_dmz extended permit udp host 192.168.69.103 any eq ntp access-list acl_dmz extended permit udp host 192.168.69.103 any eq domain access-list acl_dmz extended permit tcp host 192.168.69.103 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8080 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8099 access-list acl_dmz extended permit tcp host 192.168.69.105 any eq www access-list acl_dmz extended permit tcp host 192.168.69.103 any eq smtp access-list acl_dmz extended permit tcp host 192.168.69.105 host 192.168.68.103 eq ssh access-list acl_dmz extended permit tcp host 192.168.69.104 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq https pager lines 24 mtu outside 1500 mtu inside 1500 mtu dmz 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 static (dmz,outside) XX.XX.XX.103 192.168.69.11 netmask 255.255.255.255 static (inside,dmz) 192.168.68.17 192.168.68.17 netmask 255.255.255.255 static (inside,dmz) 192.168.68.100 192.168.68.100 netmask 255.255.255.255 static (inside,dmz) 192.168.68.101 192.168.68.101 netmask 255.255.255.255 static (inside,dmz) 192.168.68.102 192.168.68.102 netmask 255.255.255.255 static (inside,dmz) 192.168.68.103 192.168.68.103 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.104 192.168.69.100 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.105 192.168.69.105 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.102 192.168.69.10 netmask 255.255.255.255 access-group acl_out in interface outside access-group acl_dmz in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.97 1 route dmz 10.71.83.0 255.255.255.0 192.168.69.10 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 192.168.68.17 255.255.255.255 inside telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global prompt hostname context Cryptochecksum:2d1bb2dee2d7a3e45db63a489102d7de

    Read the article

  • Installed ASUS HD4670, now unable to install ANY Debian due to low memory corruption

    - by Alfabravo
    I have a desktop PC which initially had the Intel D946gzis mobo, its chipset as video controller, some RAM and so. There I installed Debian without a problem alongside WindowsXP. I've bought an ASUS HD 4670 video card, installed it on the PC and now the installed Debian does not work, while the Ubuntu live CD refuses to run no matter if I set acpi, apic on or off... it throws me some low memory corruption at position just like shown here. With normal configuration, Debian throws kernel panic (keyboard lights blinking). Anyone have faced this before? Ideas? Thanks!! (meanwhile, debian hides in a virtualbox :'( ) Edited: Tried Ubuntu 9.10 x64 (due to the fact i've a core2duo at 2GHz) and it throws a kernel-panic to me (flashing caps and num LEDs). On screen, can be read different lines with things like: ... [ 1.957161] [] rb_erase+0xd6/0x160 [ 1.957266] [] page_fault+0x25/0x30 Could it be something about this new video card having ddr3?

    Read the article

  • Unable to access VLAN host from VLAN interface in CentOS

    - by Amrit
    I am playing with VLAN (Virtual LAN) configuration on CentOS 6.4. I have 2 interfaces, eth0 and eth1. I have configured 2 VLAN interfaces eth0.20 and eth0.30 as #file: ifcfg-eth0.20 #------------- VLAN=yes DEVICE=eth0.20 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.20.1 GATEWAY=192.168.20.1 NETMASK=255.255.255.0 USERCTL=no #file: ifcfg-eth0.30 #------------- VLAN=yes DEVICE=eth0.30 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.30.1 GATEWAY=192.168.30.1 NETMASK=255.255.255.0 USERCTL=no Then connected a desktop to interface eth0 port using LAN cable and assigned 192.168.30.2/24 IP. When I try to ping 192.168.30.1 from 192.168.30.2 machine, It shows destination host unreachable. I am also not able to ping 192.168.130.2 from 192.168.30.1. However ping -I eth0 192.168.30.2 works fine. Any pointers?

    Read the article

  • Can't start httpd 2.4.9 with self-signed SSL certificate

    - by Smollet
    I cannot start the httpd 2.4.9 (tried 2.4.x too) on CentOS 6.5 with the simplest SSL config possible. The openssl version installed on the machine is OpenSSL 1.0.1e-fips 11 Feb 2013 (I've upgraded it using 'yum update' to the latest patched version as well) I have compiled and installed the httpd 2.4.9 using the following commands: ./configure --enable-ssl --with-ssl=/usr/local/ssl/ --enable-proxy=shared --enable-proxy_wstunnel=shared --with-apr=apr-1.5.1/ --with-apr-util=apr-util-1.5.3/ make make install Now I'm generating the default self-signed certificate as described in the CentOS HowTo: openssl genrsa -out ca.key 2048 openssl req -new -key ca.key -out ca.csr openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr Here is my httpd-ssl.conf file: Listen 443 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLPassPhraseDialog builtin SSLSessionCache "shmcb:/usr/local/apache2/logs/ssl_scache(512000)" SSLSessionCacheTimeout 300 <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "/usr/local/apache2/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch "MSIE [2-5]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 CustomLog "/usr/local/apache2/logs/ssl_request_log" \ "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> when I start httpd using bin/apachectl -k start I get following errors in the error_log: Wed Jun 04 00:29:27.995654 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:29:27.995726 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.995863 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996111 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:29:27.996122 2014] [ssl:info] [pid 24021:tid 139640404293376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:29:27.996209 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.996280 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996295 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:29:27.996303 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: DH PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996308 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: EC PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996318 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:29:27.996321 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I then try to generate missing DH PARAMETERS and EC PARAMETERS: openssl dhparam -outform PEM -out dhparam.pem 2048 openssl ecparam -out ec_param.pem -name prime256v1 cat dhparam.pem ec_param.pem >> /etc/pki/tls/certs/ca.crt And it mitigates the error but the next comes out: [Wed Jun 04 00:34:05.021438 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:34:05.021487 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.021874 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022050 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:34:05.022066 2014] [ssl:info] [pid 24089:tid 140719371077376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:34:05.022285 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1016): AH02540: Custom DH parameters (2048 bits) for 192.168.9.128:443 loaded from /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022389 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1030): AH02541: ECDH curve prime256v1 for 192.168.9.128:443 specified in /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022397 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.022464 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022478 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:34:05.022488 2014] [ssl:emerg] [pid 24089:tid 140719371077376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:34:05.022491 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I have tried to generate the simple certificate/key pair exactly as described in the httpd docs Unfortunately, I still get exact same errors as above. I've seen a bug report with the similar issue: https://issues.apache.org/bugzilla/show_bug.cgi?id=56410 But the openssl version I have is reported as working there. I've also tried to apply the patch from the report as well as build the latest 2.4.x branch with no success, I get the same errors as above. I have also tried to create a short chain of certificates and set the root CA certificate using SSLCertificateChainFile directive. That didn't help either, I get exact same errors as above. I'm not interested in setting up hardened security, etc. The only thing I need is to start httpd with the simplest SSL config possible to continue testing proxy config for the mod_proxy_wstunnel Had anybody encountered and solved this issue? Is my sequence for creating a self-signed certificate incorrect? I'd appreciate any help very much!

    Read the article

  • How do I roll back to the shipped version of Thunderbird?

    - by kallakafar
    I was using thunderbird v15.0 on ubuntu 12.04 LTS till now, and have the lightning extension installed to manage calendar within thunderbird application. everything was working fine until i decided to update thunderbird to the latest version 16.0 from ubuntu repository. installation was successful, and the profile everything was taken care of perfectly, except that now lightning is not working - it is disabled as lightning v1.7 is NOT compatible with latest thunderbird v16 yet. As a result i am at loss with all my scheduling. now, i would like to go back to thunderbird v15 so that i can use lightning. ubuntu repository only gives TB v16 now. on mozilla site, they are still giving v15 for linux, so i downloaded the tarball and uncompressed using command line. now i have a folder called thunderbird. there are no readme/ configuration files. there are following 'executable files' inside this folder: crashreporter, mozilla-remote-client, plugin-container, thunderbird and thunderbird-bin. i tried invoking thunderbird and thunderbird-bin from command line using sudo, still nothing is opening up. i have execute permissions for this folder contents. i m quite new to linux. please let me know why i m not able to launch thunderbird. did i install it incorrectly? please let me know if i can get a .deb package for TB v15.

    Read the article

  • Keyboard doesn't work after upgrade to Debian Wheezy

    - by mikhail
    After upgrade from lenny to wheezy keyboard and mouse don't work in X (keyboard available before it starts). I looked over internet about this issue and found some solutions: remove xorg.conf (http://forums.debian.net/viewtopic.php?f=7&t=62880) update udev and base-files (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) remove /run directory (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) reintall xserver and xorg But, nothing helped me :( Logs of X-server haven't got any messages about keyboard or mouse errors. Below you can see configuration of my system: krestyaninov@xxx# uname -a Linux xxx 3.0.0-1-686-pae #1 SMP Sat Aug 27 16:41:03 UTC 2011 i686 GNU/Linux krestyaninov@xxx# dpkg -l |grep udev ii libgudev-1.0-0 172-1 GObject-based wrapper library for libudev ii libudev0 172-1 libudev shared library ii udev 172-1 /dev/ and hotplug management daemon krestyaninov@xxx# dpkg -l |grep base-files ii base-files 6.5 Debian base system miscellaneous files krestyaninov@xxx# dpkg -l |grep xorg ii xorg 1:7.6+8 X.Org X Window System ... ii xserver-xorg 1:7.6+8 X.Org X server

    Read the article

  • Benchmarking MySQL on win7

    - by Patrick
    I've setup a nginx server running php 5.3.6 and mysql 5.5.1.3. My computer is an AMD quadcore 9650, 4gb ram, 500gb 7200rpm HD. I ran the PHP MySQL Benchmark Tool v. 0.1, and got the following results: Testing a(n) MYISAM table using 100000 rows. Successfully created database speedtestdb Sucessfully created table speedtesttable Table Type Verified: MYISAM .. Done. 100000 inserts in 19.73628 seconds or 5067 inserts per second. Done. 100000 row reads in 0.2801 seconds or 357015 row reads per second. Done. 100000 updates in 4.03876 seconds or 24760 updates per second. I'm wondering where this stands as far as performance goes, and what are some steps I can take if any to improve on this. I'm not trying to make anything fantastic, just getting a feel for how to best optimize a web server in this configuration.

    Read the article

  • RAIDZ vs RAID1+0

    - by Hiro2k
    Hi guys I just got 4 SSDs for my FreeNAS box. This server is only used to serve a single iSCSI extent to my Citrix XenServer pool and was wondering if I should setup them up in a RAIDZ or a RAID 1+0 configuration. This isn't used for anything in production, just for my test lab so I'm not sure which one is going to be better in this scenario. Will I see a major difference in speed or reliability? Currently the server has three 500GB Western Digital Blue drives and it's dog slow when I deploy a new version of our software on it, hence the upgrade.

    Read the article

  • OTBI vs. OBIA

    - by PRajkumar
      What are the differences between OTBI and OBIA?   OTBI -- Oracle Transactional Business Intelligence OBIA – Oracle Business Intelligence Applications   OBIA   1. OBIA is the pre-packaged BI Apps that Oracle has provided for several years. It is the data warehouse based Solution 2. It is based on the Universal data warehouse design with different prebuilt adapters that can connect to various source application to bring the     data into the warehouse 3. It allows consolidating the data from various sources to bring them together 4. It provides a library of metrics that help to measure business 5. It provides set of predefined reports and dashboards 6. OBIA works for multiple sources including E-Business Suite, PeopleSoft, JDE, SAP and FUSION Applications    OTBI 1. It is a real time BI 2. There is no warehouse or ETL process for OTBI 3. It is a Fusion Apps only 4. OTBI leveraging the advanced technologies from both BI platform and ADF to enable the online BI queries against database directly 5. OTBI does not have prebuilt dashboards and reports like OBIA   Note: Both OTBI and OBIA are available from same metadata repository. Some of the repository objects are shared between OTBI and OBIA. It was designed to allows to have following configuration:   OTBI Only OBIA Only OTBI and OBIA coexist    Both OTBI and OBIA are accessing Fusion Apps via the ADF

    Read the article

  • MySQL is hogging my server resources

    - by Reacen
    Does anyone have any idea of what can cause this weird behaviour and how I go about fixing it? This is all coming from MySQL only (both RAM and CPU usage), for about 10 minutes after I reboot my Java game server (that has a pool of 256 connections). There are not that many queries and I think it may be more of a MySQL misconfiguration problem. My server: 3.20 GHz * 6 core / 24 GB RAM / 64 bit Windows Server 2003. My game server: Java server, with 256 MySQL connections pool (MyISAM engine), about 500,000 accounts, and 9 million rows of game items in database and about 3,000 players are connected. After about 15 minutes of the game server reboot, the server resumes its stability and CPU usage drop down to 1% ~ 5% and memory to 6 GB. Here is a copy of my MySQL configuration. Also, any advice about my MySQL configuration will be appreciated. I really set it up almost at random. # Example MySQL config file for very large systems. # # This is for a large system with memory of 1G-2G where the system runs mainly # MySQL. # # You can copy this file to # /etc/my.cnf to set global options, # mysql-data-dir/my.cnf to set server-specific options (in this # installation this directory is C:\mysql\data) or # ~/.my.cnf to set user-specific options. # # In this file, you can use all long options that a program supports. # If you want to know which options a program supports, run the program # with the "--help" option. # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /tmp/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] #log=c:\mysql.log port = 3306 socket = /tmp/mysql.sock skip-locking key_buffer_size = 2572M max_allowed_packet = 64M table_open_cache = 512 sort_buffer_size = 128M read_buffer_size = 128M read_rnd_buffer_size = 128M myisam_sort_buffer_size = 500M thread_cache_size = 32 query_cache_size = 1948M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 12 max_connections = 5000 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # #skip-networking # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 # Replication Slave (comment out master section to use this) # # To configure this host as a replication slave, you can choose between # two methods : # # 1) Use the CHANGE MASTER TO command (fully described in our manual) - # the syntax is: # # CHANGE MASTER TO MASTER_HOST=<host>, MASTER_PORT=<port>, # MASTER_USER=<user>, MASTER_PASSWORD=<password> ; # # where you replace <host>, <user>, <password> by quoted strings and # <port> by the master's port number (3306 by default). # # Example: # # CHANGE MASTER TO MASTER_HOST='125.564.12.1', MASTER_PORT=3306, # MASTER_USER='joe', MASTER_PASSWORD='secret'; # # OR # # 2) Set the variables below. However, in case you choose this method, then # start replication for the first time (even unsuccessfully, for example # if you mistyped the password in master-password and the slave fails to # connect), the slave will create a master.info file, and any later # change in this file to the variables' values below will be ignored and # overridden by the content of the master.info file, unless you shutdown # the slave server, delete master.info and restart the slaver server. # For that reason, you may want to leave the lines below untouched # (commented) and instead use CHANGE MASTER TO (see above) # # required unique id between 2 and 2^32 - 1 # (and different from the master) # defaults to 2 if master-host is set # but will not function as a slave if omitted #server-id = 2 # # The replication master for this slave - required #master-host = <hostname> # # The username the slave will use for authentication when connecting # to the master - required #master-user = <username> # # The password the slave will authenticate with when connecting to # the master - required #master-password = <password> # # The port the master is listening on. # optional - defaults to 3306 #master-port = <port> # # binary logging - not required for slaves, but recommended #log-bin=mysql-bin # # binary logging format - mixed recommended #binlog_format=mixed # Point the following paths to different dedicated disks #tmpdir = /tmp/ #log-update = /path-to-dedicated-directory/hostname # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = C:\mysql\data/ #innodb_data_file_path = ibdata1:2000M;ibdata2:10M:autoextend #innodb_log_group_home_dir = C:\mysql\data/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 384M #innodb_additional_mem_pool_size = 20M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 100M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 [mysqldump] quick max_allowed_packet = 64M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [myisamchk] key_buffer_size = 256M sort_buffer_size = 256M read_buffer = 8M write_buffer = 8M [mysqlhotcopy] interactive-timeout

    Read the article

  • Java Spotlight Episode 105: Mark Reinhold on the Future of Java

    - by Roger Brinkley
    Our yearly interview with Mark Reinhold, Chief Java Architect, Java Platform Group on the future of Java. Right-click or Control-click to download this MP3 file. You can also subscribe to the Java Spotlight Podcast Feed to get the latest podcast automatically. If you use iTunes you can open iTunes and subscribe with this link:  Java Spotlight Podcast in iTunes. Show Notes News Two Java Update Releases New Java SE 6 software updates from Apple for OS X 10.8, 10.7 and 10.6 are now live and available to all customers via the Mac App Store / Software Update. The JavaFX Community Site on Java.net JSR 360: Connected Limited Device Configuration 8 JSR 361: Java ME Embedded Profile 2012 JCP EC Election Ballot open Meet the EC Candidates Recording and Materials Events Oct 22-23, Freescale Technology Forum - Japan, Tokyo, Japan Oct 23-25, EclipseCon Europe, Ludwigsburg, Germany Oct 30-Nov 1, Arm TechCon, Santa Clara, United States of America Oct 31, JFall, Hart van Holland, Netherlands Nov 2-3, JMaghreb, Rabat, Morocco Nov 5-9, Øredev Developer Conference, Malmö, Sweden Nov 13-17, Devoxx, Antwerp, Belgium Nov 20-22, DOAG 2012, Nuremberg, Germany Dec 3-5, jDays, Göteborg, Sweden Dec 4-6, JavaOne Latin America, Sao Paolo, Brazil Feature InterviewMark Reinhold is Chief Architect of the Java Platform Group at Oracle, where he works on the Java Platform, Standard Edition, and OpenJDK. His past contributions to the platform include character-stream readers and writers, reference objects, shutdown hooks, the NIO high-performance I/O APIs, library generification, and service loaders. Mark was the lead engineer for the 1.2 and 5.0 releases and the specification lead for Java SE 6. He is currently leading the Jigsaw and JDK 7 Projects in the OpenJDK Community. Mark holds a Ph.D. in Computer Science from the Massachusetts Institute of Technology. In this interview he discusses the future of Java Platform with regards to Jigsaw, Lambda, and Nashorn components as well as the OpenJDK community. What’s Cool QotD: Ubuntu 12.10 Release Notes on OpenJDK 7 New Lambda binary drop Development forest for Compact Profiles (JEP 161)

    Read the article

  • DDD Melbourne -lessons leant

    - by Michael Freidgeim
    I've attended DDD Melbourne and want to list the interesting points, that I've leant and want to follow. To read more: * Moles-Mocking Isolation framework for .NET. Documentation is here.   (See also Mocking frameworks comparison created October 4, 2009 ) * WebFormsMVP * PluralSight   http://www.pluralsight-training.net/offers/default.aspx?cc=trial   * ELMAH: Error Logging Modules and Handlers *Rhino.Mocks   * VS UI Test Recorder -see posts Visual Studio 2010 Coded UI Test User Guide. Note that Microsoft Test Manager (MTM) toolis a separate application, that can be started from Program files/VS 2010 menu.It is not a menu inside Visual Studio.   * CodeContract- seems great in Debug. Will be good if in production  will be possible runtime configuration, ability to log instead of throw exception. Current recommendation to customize Debug.Assert is not trivial The programmer is free to use the customization provided by Debug.Assert using assert listeners to obtain whatever runtime behavior they desire (e.g., ignoring the error, logging it, or throwing an exception).   // Clears the existing list of assert listener (the default pop-up box) System.Diagnostics.Debug.Listeners.Clear(); // Install your own listener System.Diagnostics.Debug.Listeners.Add(MyTraceListener); Note that you can't catch specific ContractException, but can catch generic Exception(see How come you cannot catch Code Contract exceptions?)   Books recommended "Working effectively with legacy code" by Michael Feathers (corresponding article)   Fowler, Martin Refactoring: Improving the Design of Existing Code, slides http://jaoo.dk/jaoo1999/schedule/MartinFowlerRefractoring.pdf

    Read the article

  • Jetty - Virtualhosting - SSL Certificates

    - by Walter White
    Hi all, I want to have different SSL certificates for different domains that I am hosting in a single Jetty instance. I do not want to front my Jetty application server with Apache. I am running Jetty 6.1.22. So far, I have only seen configurations with a single SSL certificate, and the configuration for SSL happens within server which leads me to believe that Jetty was designed to support a single SSL certificate. Please let me know if I can use Jetty with more than 1 certificate. I am considering migrating to JBoss Application Server 6.0 since it is closer to a real application server. Is this something that can be done there, and is it a supported feature? Walter

    Read the article

  • How to install mod_ssl for Apache

    - by Nick Foote
    Ok So I installed Apache httpd a while ago and have recently come back to it to try setup SSL and get it serving several different tomcat servers. At the moment I have two completely separate tomcat instances serving up to slightly different versions (one for dev and one for demo say) my web app to two different ports; mydomain.com:8081 and mydomain.com:8082 I've successfully (back in Jan) used mod_jk to get httpd to serve those same tomcat instances to http://www.mydomain.com:8090/dev and http://www.mydomain.com:8090/demo (8090 cos I've got another app running on 8080 via Jetty at this stage) using the following code in httpd.conf; LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log JkLogLevel debug <VirtualHost *:8090> JkMount /devd* tomcatDev JkMount /demo* tomcatDemo </VirtualHost> What I'm not trying to do is enable SSL I've added the following to httpd.conf Listen 443 <VirtualHost _default_:443> JkMount /dev* tomcatDev JkMount /demo* tomcatDemo SSLEngine on SSLCertificateFile "/opt/httpd/conf/localhost.crt" SSLCertificateKeyFile "/opt/httpd/conf/keystore.key" </VirtualHost> But when I try to restart Apache with "apachectl restart" (yes after shutting down that other app I mentioned so it doesn't toy with https connections) I continuously get the error; "Invalid command 'SSLEngine', perhaps misspelled or defined by a module not included in the server configuration. httpd not running, trying to start" I've looked in the httpd/modules dir and indeed there is no mod_ssl, only mod_jk.so and httpd.exp. I've tried using yum to install mod_ssl, it says its already installed. Indeed I can locate mod_ssl.so in /usr/lib/httpd/modules but this is NOT the path to where I've installed httpd which is /opt/httpd and in fact /usr/lib/httpd contains nothing but the modules dir. Can anyone tell me how to install mod_ssl properly for my installed location of httpd so I can get past this error:

    Read the article

  • Generate webservice proxy using oracle ant tasks

    - by adrian.muraru
    Proxy generation tends to be very slow when done using jdeveloper wizard and even more this time increases when jdeveloper is started over a remote desktop connection. So here's step-by-step howto that can be used to generate webservice proxy from your *nix shell Create a dir in your scratch area : e.g. /tmp/<username>/genproxy Get build.xml file attached, save it in the dir above and change the properties defined in it to match your ws endpoint. More specifically you need to edit: proxy.wsdl - the path (either locally or URL) where WSDL file can be accessed from proxy.handler - the handler class proxy.package - the class package where the proxy will be generated Start a new shell session (out of the ADE view if you're using one) and set the environment needed for proxy generation using ant and Oracle WebServicesAssembler genProxy [1] $ setenv ORACLE_HOME /opt/jdev_local/10.1.3/ $ setenv PATH $ORACLE_HOME/ant/bin:$PATH Note that the above env setup is needed even if you already have ORACLE_HOME set and ant utiliy available in your PATH. That way you'll be sure the proxy will be generated using the same libraries your jdeveloper is using in its wizard Generate proxy $ cd /tmp/<username>/genproxy $ ant genproxy And voila, the proxy files should be available in ./src directory. Notes: [1] More information about genProxy can be found at : http://download.oracle.com/docs/cd/B32110_01/web.1013/b28974/wsassemble.htm#CHDJJIEI [2] In my case this method is much faster then using the jdeveloper wizard (15secs compared to 25minutes) [3] There is one minor drawback though, the jdeveloper .proxy configuration file is not generated. -Adrian

    Read the article

  • Can I have different ESX hosts accessing the same LUN over different protocols?

    - by Kevin Kuphal
    I currently have a cluster of two ESX 3.5U2 servers connected directly via FiberChannel to a NetApp 3020 cluster. These hosts mount four VMFS LUNs for virtual machine storage. Currently these LUNs are only made available via our FiberChannel initator in the Netapp configuration If I were to add an ESXi host to the cluster for internal IT use can I: Make the same VMFS LUNs available via the iSCSI initiator on the Netapp Connect this ESXi host to those LUNs via iSCSI Do all of this while the existing two ESX hosts are connected to those LUNs via FiberChannel Does anyone have experience with this type of mixed protocol environment, specifically with Netapp?

    Read the article

  • 500 - Internal server error on IIs 7.5 R2

    - by StealthRT
    Hey all, i have a windows 2008 Web Edition R2 VPS and i seem to be having problems with it pointing to my domain name. I get this error when i visit my web address: Server Error 500 - Internal server error. There is a problem with the resource you are looking for, and it cannot be displayed. I'm sure theres a configuration problem somewhere but i am currently unable to find it. And i'm also new at the windows server so any step-by-step help would be greatly appreciated! David

    Read the article

  • Adding Facebook IPv6 to Centos, getting CurlException 7

    - by Nick
    I'm correctly get following error. After searching about this issue, correct me if i'm wrong, I believe that adding/configuring IPv6 should solve the problem. PHP Fatal error: Uncaught CurlException: 7: Failed to connect to 2a03:2880:10:8f02:face:b00c:0:26: Network is unreachable\n thrown in /var/www/vhosts/facedex.net/httpdocs/fb/apps/seemyfuture/src/base_facebook.php on line 886 The problem is I dont know the right way to add it. There seems to have may methods. http://tldp.org/HOWTO/Linux+IPv6-HOWTO/x1035.html#AEN1044 http://unix.stackexchange.com/questions/34093/static-ipv4-ipv6-configuration-on-centos-6-2 My netstat show this. Shell doesnt recogize -rn6 though.It shows invalid option -- 6 netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 27.254.38.128 0.0.0.0 255.255.255.128 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 27.254.38.254 0.0.0.0 UG 0 0 0 eth0 FYI: I'm using Centos 5.7. Thank you a lot in advance.

    Read the article

  • SharePoint 2010 Design & Deployment Best Practices

    - by Michael Van Cleave
    Well now that SharePoint 2010 has successfully launched and everyone is scratching for every piece of best practices information they can get their hands on, I would like to invite anyone and everyone to come and take part in ShareSquared's next webinar. The webinar will cover some key information such as: Pros and cons of the different approaches to installing and configuring SharePoint 2010 Configuration Best Practices for SharePoint 2010 farms Services architecture; dependencies, licensing, and topologies Information Architecture guidance for sizing, multilingual support, multi-tenancy, and more. Using tools such as SharePoint Composer and SharePoint Maestro to configure and deploy SharePoint 2010 And most of all, avoiding common pitfalls for installation and deployment. What is better than all of that? Well, the even more exciting thing is that the presenters will be our very own SharePoint MVP's Gary Lapointe and Paul Stork. If you don't know who these guys are then you should definitely check out their blogs and their contributions to the SharePoint community. To get more information and register click here: REGISTER Other great links to information in this post: ShareSquared, Inc Gary Lapointe's Blog Paul Stork's Blog SharePoint Composer Check it out and get up to speed from some of the best in the industry. Michael

    Read the article

  • Linux DNS Multi tenant

    - by spicyramen
    I need to setup a multi-tenant DNS solution in Linux DNS Server. Currently I serve multiple companies: Company ABC, Company XYZ, etc... I need to create a) Forwarder zone b) Reverse Forward Zone. I can easily create a Forward Zone with domain abc.com The challenge I have is that each of my customer components share the same IP address. Hence If I create the Reverse Forward Zone I end up with something like this: abc.com 1.1.1.1 host.abc.com xyz.com 1.1.1.1 host.xyz.com If I perform a reverse lookup on host.abc.com it works fine...but if I do a reverse lookup on 1.1.1.1 I get a load balance response of: attempt: host.abc.com attempt: host.xyz.com attempt: host.abc.com Any ideas? I want to add logic to the DNS configuration to handle DNS reverse lookup based on source machine and respond with right hostname. Workaround: Create multiple DNS but this is not scalable.

    Read the article

  • How can I use VirtualDocumentRoot to serve the www subdomain with SSL enabled?

    - by mdgreenwald
    I am able to serve http://www.domain.com and http://domain.com. Also https://domain.com works fine too. But not https://www.domain.com for some reason this doesn't work. I even created a www.domain.com in my sites-availible folder and also enabled it. I reloaded the configuration and yet it still doesn't work. I have a wildcard certificate so that is NOT the problem. <IfModule mod_ssl.c> <VirtualHost *:443> ServerAdmin [email protected] ServerName *.domain.com:443 ServerAlias www.domain.com VirtualDocumentRoot /var/www/%0 Thanks for any help.

    Read the article

  • Install IIS windows 7

    - by rad
    I have tried many way to install IIS in my Windows 7 Professionnel environment. And I have always an error. I tried with Web Plateform Api - "Fatal Error during installation" With Windows Features in configuration pannel - "An error has occurred. Not all of the features were successfully" With command line (http://forums.iis.net/t/1152513.aspx) - "Fatal Error during installation" in log file I have IIS.log : [04/10/2012 16:13:25] "C:\Windows\SysWOW64\inetsrv\aspnetca.exe" /install /basic 2.0.50727.0 [04/10/2012 16:13:25] < !!FAIL!! RegOpenKeyEx(HKLM\SYSTEM\CurrentControlSet\Services\ASP.NET_2.0.50727\Names) result=0x80070002 [04/10/2012 16:13:25] < !!FAIL!! SetAccessToPerfCountersKeys() result=0x80070002 [04/10/2012 16:13:25] < !!FAIL!! Installation failure, result=0x80070002 If I uninstall/reinstall IIS, I have some error but my site run correctly, and after windows restart, the install is rollbacked and I lose my installation. Any help ?

    Read the article

  • Thinking of Adopting the PRINCE2™ Project Management Methodology? Consider Using PeopleSoft Projects to Help

    - by Megan Boundey
    Ever wondered what the PRINCE2™ project management methodology is? Ever wondered if you could use PeopleSoft Projects (ESA) to manage your projects using PRINCE2™?  Published by the Office of Government Commerce in the UK, PRINCE2™ is a scalable, business case and product description-driven Project Management methodology based upon managing by exception. Project activities are organized around fulfilling and meeting the product description. Quality assurance, configuration control and risk management are all based upon ensuring that the product delivered accurately meets the product description. PRINCE2™ is built upon seven principles and seven themes, each underpinning the PRINCE2™project management processes. Important for today’s business environment, the focus throughout PRINCE2™ is on the Business Case, which describes the rationale and business justification for a project. The Business Case drives all the project management processes from initial project setup to successful finish. PRINCE2™, as a method and a certification, is adopted in many countries worldwide, including the UK, Western Europe and Australia. We’ve just released a new white paper, which provides you with an overview of the principles, themes and project management processes associated with PRINCE2™. It also shows how these map to the functionality available within PeopleSoft Projects (ESA). In the time it takes to drink a coffee, you can learn about PRINCE2™ and determine whether it might help you deliver better project results. We encourage you to take a look.

    Read the article

  • Running a reverse proxy in front of Splunk 4.x

    - by sgerrand
    So, I have previously installed Splunk 3.x behind a reverse proxy and downloaded the latest version (4.0.6 at time of typing) expecting it to be as easy to use as before. Sadly this was not the case. There appears to be some elements which are not being translated correctly through the reverse proxy, causing Splunk to fail. I have used the following configuration in Apache2 to no avail: ServerName monitoringbox.com DocumentRoot /path/to/nowhere ProxyRequests off ProxyPass /splunk http://127.0.0.1:8000/splunk ProxyPassReverse /splunk http://127.0.0.1:8000/splunk Order allow,deny Allow from all Has anyone else had more luck than me in setting up Splunk 4.x behind a reverse proxy?

    Read the article

  • Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)

    - by Bakhtiyor
    I have mailserver configure using dovecot+postfix+mysql and it was runnig fine in the server(Ubuntu Server). But during last week it stopped working correctly. It doesn't send email. When I try to telnet localhost smtp I'm connecting successfully but when I do mail from:<[email protected]> and hit Enter it hangs on, nothing happen. Having reviewed /var/log/mail.log file I've found out that probably(99%) the problem is on postfix when it is trying to connect to MySQL server. If you see the log file given below you can see that it says Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2). Nov 14 21:54:36 ns1 dovecot: dovecot: Killed with signal 15 (by pid=7731 uid=0 code=kill) Nov 14 21:54:36 ns1 dovecot: Dovecot v1.2.9 starting up (core dumps disabled) Nov 14 21:54:36 ns1 dovecot: auth-worker(default): mysql: Connected to localhost (mailserver) Nov 14 21:54:44 ns1 postfix/postfix-script[7753]: refreshing the Postfix mail system Nov 14 21:54:44 ns1 postfix/master[1670]: reload -- version 2.7.0, configuration /etc/postfix Nov 14 21:54:52 ns1 postfix/trivial-rewrite[7759]: warning: connect to mysql server localhost: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) Nov 14 21:54:52 ns1 postfix/trivial-rewrite[7759]: fatal: mysql:/etc/postfix/mysql-virtual-alias-maps.cf(0,lock|fold_fix): table lookup problem Nov 14 21:54:53 ns1 postfix/master[1670]: warning: process /usr/lib/postfix/trivial-rewrite pid 7759 exit status 1 Nov 14 21:54:53 ns1 postfix/cleanup[7397]: warning: problem talking to service rewrite: Connection reset by peer Nov 14 21:54:53 ns1 postfix/master[1670]: warning: /usr/lib/postfix/trivial-rewrite: bad command startup -- throttling Nov 14 21:54:53 ns1 postfix/smtpd[7071]: warning: problem talking to service rewrite: Success I tried netstat -ln | grep mysql and it returns unix 2 [ ACC ] STREAM LISTENING 5817 /var/run/mysqld/mysqld.sock. The content of /etc/postfix/mysql-virtual-alias-maps.cf file is here: user = stevejobs password = apple hosts = localhost dbname = mailserver query = SELECT destination FROM virtual_aliases WHERE source='%s' Here I tried to change hosts = 127.0.0.1 but it says warning: connect to mysql server 127.0.0.1: Can't connect to MySQL server on '127.0.0.1' (110) So, I am lost and don't know where else to change in order to solve the problem. Any help would be appreciated highly. Thank you.

    Read the article

< Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >