Search Results

Search found 8850 results on 354 pages for 'xp'.

Page 319/354 | < Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• My SSD stopped working as it ends up in blue death right after windows 7 launches, how can I reset it for new windows install?

  - by HattoriHanzo

  As I mentioned in the title my SSD suddenly started to fail as after launching Windows 7 it goes straight to completely idle and after a few minutes it goes to blue death and restarts. I have an another HD with a windows xp on it and it works fine and I can also see the SSD and can access everything on it. Windows 7 on the SSD does work in safe mode though yet I didn't manage to find out what causes the problem. Since I can sill access the files and save them to another HD I'm looking for the best way to wipe and reinstall Windows 7. I have yet failed to find an easy to follow (or even understand) guide, different sources on the internet recommend different ways of doing this. And some guides are just simply full of terms I have no clue about. It's an OCZ Vertex 2 120GB. I"d very much appreciate if someone could give me an advice on what I should do, preferably in a way so I could regain the best possible performance as well. it doesn't matter if I don't understand the science behind it as long as I can follow the steps. Thanks!

  Read the article

• I cannot connect to home server after a few hours

  - by Iago

  I have an old PC and I decided to revive it. A LAMP (for my own use) and a P2P server (torrent and e2dk). My old PC is an AMD Athlon XP (1400 MHz) with 384 Mb of RAM First of all I installed Ubuntu Server 11.10, SSH, FTP, SAMBA and LAMP. With this configuration my home server works well, with no problem. Then I went to the P2P server and I tried rTorrent and then uTorrent Server Alpha. And here is my problem. After a few hours (maybe 10 hours, or maybe 30 hours) with the torrent app running (rTorrent or uTorrent) I lose the connection to my home server. That is, I cannot access via ssh, I cannot access the apache server, etc. but I can ping the home server. It seems that the server freezes and all I can do is reboot the server physically. So, I have two questions: What is the problem? and How can I solve it?

  Read the article

• Synchronize Dreamweaver over an SSH tunnel using an SFTP connection

  - by Aeo

  Maybe... Just maybe... I'm asking too much here. Maybe I'm even barking up the wrong tree. I'm looking to essentially have Dreamweaver establish an SSH tunnel to one machine, and then use that connection to synchronize a site that is on another machine entirely. Now for some details: We've got two connections here at work. We've got our office connection for day to day business, and then we've got some fancy connection hosting our web servers upstairs. For the most part they've been mutually exclusive until recently. We had been establishing an SFTP connection to synchronize our web sites by going out over the office connection to the web and coming back in over the fancy connection to our servers upstairs. Recently -ish, we established a LAN connection to one of our servers that makes a pleasant change in VNC connection quality. Thanks to Vinagre, this makes it really easy to connect to any of our servers over this LAN connection via SSH tunnel for VNC. However, in spite of that new addition of a LAN connection, we still synchronize over the 'net. Out the office connection and in on the fancy one upstairs. I'm looking to change this. I'd like to get Dreamweaver to first tunnel over our LAN connection to the servers, and then go from there to whatever connection it needs to. Am I asking too much? The current set up: Dreamweaver is installed on Windows XP which is running within VirtualBox on top of Ubuntu 10.10. The network connection for VirtualBox is currently made in NAT mode, but could easily be switched to a Bridged Connection should it need be. The LAN connection is to 1 of 5 servers running CentOS 5.

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• Windows 7 Explorer: how to show total size of all files in current folder?

  - by matt wilkie

  In Windows XP Explorer one can turn on Status Bar which shows, among other things, the total size of all the files in the current folder, or if the cumulative size of the selected files. How do I get the same at-a-glance information in Windows 7? Selecting files doesn't count as it stops after 15 files, and it's rare that I'm concerned about total size with that few files (it's pretty easy to estimate in my head). thanks. UPDATE: Information derived from the context menu (select r-click properties) isn't "at a glance", and not as smooth as selecting files and clicking the details link at the bottom in any case. Thank you for fleshing out more of the available routes though. Yes Q19232 is similar to this one, though it is not a duplicate. That question is about looking for easy free-space on disk stats and this one is easy used-space by contents of this folder stats. The answer for both is the same though. You can't! Hopefully someone will figure how to get this lost feature back with a shell extension or something.

  Read the article

• How to disable Utility Manager (Windows Key + U)

  - by Skizz

  How do I disable the Windows + U hotkey in Windows XP? Alternatively, how do I stop the utility manager from being active? The two are related. The utilty manager is currently providing a potential security hole and I need to remove it[1]. The system I'm developing uses a custom Gina to log in and start a custom shell. This removes most Windows Key hotkeys but the Win + U still pops up the manager app. Update: Things I've tried and don't work: NoWinKeys registry setting - this only affects explorer hotkeys; Renaming utilman.exe - program reappears next login; Third party software - not really an option, these machines are audited by the clients and additional, third party software would be unlikely to be accepted. Also, the proedure needs to be reasonably straightforward - this has to be done by field service engineers to existing machines (machines currently in Russia, Holland, France, Spain, Ireland and USA). [1] The hole is via the internet options in the help viewer the utility app links to.

  Read the article

• MBR seems to be gone

  - by bobobobo

  So, horror story for everyone. I bought two spanking new HDD's. MM!! Gbitage. I removed all my old HDD's, physically labelled them, and was preparing to install all new HDD's (fresh sys install included!) To make sure what HDD was what, I popped each OLD HDD (data filleD!) into a Thermaltake Blacx toaster.. surprisingly BOTH couldn't be read. I didn't have static on my hands! I'm certain of it. I touched metal, touched wood, before beginning this all. Thinking that was strage, I hauled up the new sys, installed Win XP (of course!) on the new HDD, and now the two OLD HDD's (data filled!) that were entered into the toaster cannot be read. And they had tons of data on them. I read about MBR's being nuked and it sounds like that is what it is. But I'm at a loss what to do. There are so many MBR recovery programs out there, I kind of feel overwhelmed. I don't want to lose my data by just pikcing one, yet it seems so close within reach, I'm not panicking anymore.. Anybody have a play by play that I could follow? I just don't want to spend $900 on data recovery centers if I can do this myself..

  Read the article

• Linux file server for an inexperienced admin

  - by Pat

  A charity I volunteer for wants a file server for their mostly Windows machines (about five XP and 7 machines, with some Mac laptops every now and then). For the server, I have a PC with an Intel Core 2 Duo 3GHz proc, 4GB of DDR2 400MHz RAM, and a 500 GB HDD. (I should point out that they do not currently have any server - they are just using Windows to share a folder on one of the PCs.) What is a linux distro that is easy to configure for Windows file serving yet stable and secure enough to protect sensitive data without an expert sysadmin? I'm guessing that a Debian distro would probably fit the security bill, but I don't know of any tailored to novice sysadmins. Also, are there any killer apps for making this easy to administer and set up (as a Windows file server, in particular - this answer is a good example)? Would FreeNAS be sufficient? Once it's all set up, what are the minimum measures I need to take to keep the data secure? I found this somewhat helpful answer, but it's not specific to my question of just getting a secure file server up, running, and maintained.

  Read the article

• Multiple copies off the same printer on Windows 7 from PrintUIEntry

  - by Kev

  I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• HD working with IDE USB adapter but not recognised by bios

  - by Rajeeva

  I have a Windows XP Pentium III desktop with two hard drives. The first one has the OS and is luckily working. The second drive on the secondary master IDE channel few days back was unable to read some files and since then for some time it was failing and reviving intermittently and now it is always showing as failed on the IDE channel When the HD was intermittenly failing, I was able to copy some data from it to the other drive - also during that time if the system was running and the hard disk failed at that time, the system froze and then i had to reboot. then I got a new 80 gb hdd similar (same make - seagate barracuda) to the earlier failing one, a new data cable for the drive and an IDE to USB adapter. the new hard drive i installed in the previous drive's place (secondary master), formatted it and it worked for 1 day and then it also failed - simultaneously i connected the old hd to the IDE/USB adapter and i could view all the data - some of that data i was able to back up from the old hd to the new hd before the new hd failed the new hd i have tried connecting on the primary channel as the slave disk but when i do that then the bios does not detect either the OS drive or the new drive and the system does not boot surprisingly, the older (previously failed) hd and the new hd are both working fine on the usb channel with the IDE/USB adapter. i have ruled out any problem with the secondary channel since the dvd rom i was earlier using as primary slave have now connected to secondary master and it works fine. i am really confused by this behavior on my system. please can anybody try to solve this for me. thanks.

  Read the article

• Windows 7 SSH file server

  - by Siriss

  Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

  Read the article

• Chrome Lockups Windows 7 64-bit

  - by Mike Chess

  I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

  Read the article

• What are ways to prevent files with the Right-to-Left Override Unicode character in their name (a malware spoofing method) from being written or read?

  - by galacticninja

  What are ways to avoid or prevent files with the RLO (Right-to-Left Override) Unicode character in their name (a malware method to spoof filenames) from being written or read in a Windows PC? More info on the RLO unicode character here: http://www.fileformat.info/info/unicode/char/202e/index.htm http://en.wikipedia.org/wiki/Bi-directional_text Info on the RLO unicode character when used by malware: http://www.ipa.jp/security/english/virus/press/201110/E_PR201110.html Mirror link: http://webcache.googleusercontent.com/search?q=cache:KasmfOvbVJ8J:www.ipa.jp/security/english/virus/press/201110/E_PR201110.html+&cd=1&hl=en&ct=clnk You can try this RLO character test webpage: http://www.fileformat.info/info/unicode/char/202e/browsertest.htm The RLO character is also already pasted in the 'Input Test' field in that webpage. Try typing there and notice that the characters you're typing are coming out in their reverse orders (right-to-left, instead of left-to-right). In filenames, the RLO character can be specifically positioned in the filename to spoof or masquerade as having a filename or file extension that is different than what it actually has. (Will still be hidden even if 'Hide extensions for known filetypes' is unchecked.) The only info I can find that has info on how to prevent files with the RLO character from being run is from the Information Technology Promotion Agency, Japan website: http://www.ipa.jp/security/english/virus/press/201110/E_PR201110.html (Mirror link). They adviced to use the Local Security Policy settings manager to block files with the RLO character in its name from being run. Can anyone recommend any other good solutions to prevent files with the RLO character in their names from being written or being read in the computer, or a way to alert the user if a file with the RLO character is detected? My OS is Windows 7, but I'll be looking for solutions for Windows XP, Vista and 7, or a solution that will work for all those OSes, to help people using those OSes too.

  Read the article

• How to handle OpenVPN client as a service, when the laptop is physically on the network already?

  - by James

  The Setup I've gotten OpenVPN working on our Windows XP laptops. Users are limited, so I went ahead and set OpenVPN client to run as a service, which is great anyway because that means they are on the VPN before logging in, so login scripts work, plus we can do remote support even if the user can not log in (such as connecting via VNC or resetting passwords). It is also configured to send all traffic over the tunnel, so when, for example, they browse the internet it is just like browsing from our corporate network. The Qestion(s) So, I'm wondering how does the OpenVPN client act when the computer is already physically on the same network as the OpenVPN server? Right now, the client is configured to connect the the public dns name which will resolve to the public ip address which will NOT get reflected back to the OpenVPN server, so it is affectively blocked from connecting to the OpenVPN server while on the network. Is that a good thing? Or will it constantly try to connect, using up system resources and network resources? We will likely have hundreds of laptops regularly on the physical network with this, so it could contribute to a lot of unnecessary network chatter. Alternatively Would it be better to have the firewall reflect the port back to the OpenVPN server and let it connect? Or have our internal dns resolve the name to the private ip and allow them to connect directly? Would traffic then go over the vpn connection (which I do not want, when already on the physical network)? Or is it possible to tell it to ignore the connection when the client and server are already on the same network? TLDR What's a sane way of handling OpenVPN client running as an always-on service when the client and server will often be on the same network?

  Read the article

• How do I get rid of these "There is a problem with your tablet driver" messages?

  - by Adam Rosenfield

  Every time I run certain applications (including but not limited to GIMP, Microsoft Visual Studio, and 3DS Max), I get the following message box: There is a problem with your tablet driver. Please reboot your system. If the problem persists reinstall or update the driver. Obviously I've tried rebooting and that hasn't fixed anything. Secondly, I'm not running a tablet PC. This is just Windows XP SP3 running on a Dell Precision PWS490 desktop workstation. How do I get rid of these error messages? The applications still load normally after dismissing them, but they're rather annoying. Using Process Explorer, I got the call stack from the message box. It's coming from wintab32.dll. Here's the call stack when running GIMP (irrelevant frames omitted): ... 8 USER32.dll!MessageBoxA+0x45 9 wintab32.dll!WTMgrPacketHookExA+0x44a 10 libgdk-win32-2.0-0.dll!gdk_display_list_devices+0x37 ... So, does anyone know how I can get an updated version of wintab32.dll or have any other ideas? I've been keeping my system up to date with Windows Updates. The timestamp on wintab32.dll is 2007-03-30 17:38, and its MD5 sum is ffdc332007c9dc6dd346c8ac2b09a015.

  Read the article

• How do I tell Windows to use 802.11 in preference to 3G?

  - by Jon Skeet

  I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks.

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• In Windows 7, why won't my display stay off despite the power settings saying it should?

  - by Jer

  I'm completely stumped by this. My simple use case is that when I'm in bed, I use a cordless mouse to browse the web, watch videos, etc. - the monitor is across the room. When I'm going to sleep, I want to shut the monitor off. I also want to be able to turn it back on in the morning. I just want to turn the monitor off and on using only the mouse. I thought of creating a power setting that turned the monitor off asap (the shortest amount of time is one minute; that's fine). I have one that does this. It worked great for almost a year on my old XP machine, and for about four months on my new Windows 7 laptop (which I essentially use as a desktop). All of a sudden a couple weeks ago, it just stopped working - my monitor won't turn off on its own anymore. Here are the settings: I tried other options. Based on the advice here I tried nircmd. This seemed great. I created a shortcut with the command line: "C:\Program Files\nircmd\nircmd.exe" cmdwait 1000 monitor off I click this, and in one second the monitor goes off. However about five seconds later it turns back on, and I've been extra careful to make sure the mouse isn't moving. I have no idea what's going on. Based on both of these things, my only guess is that something could be running in the background which somehow makes the computer think it's in use. I've tried killing as many programs as possible but I still get the same behavior. Any advice? I'm mainly curious about how to debug, but am open to other suggestions about turning the monitor off and on with just the mouse as well.

  Read the article

• How can I automatically edit an email before auto-forwarding it?

  - by Miss Cellanie

  Is there a way to automatically edit emails before forwarding them? I'm getting email notifications from Foursquare that I want to send to my phone as text messages. I know how to send messages to my number using an email address (I'm in the US and use Verizon) but I don't know how to strip out any unnecessary formatting, like HTML, before the email gets sent. What I want: Ability to strip out HTML Ability to start forwarding at a specific part of the email based on a search (e.g., I might know that Foursquare starts their messages with "Hey hey!" and only want content after that phrase occurs) Ability to truncate at 160 characters Things I've tried: I'm not using Foursquare DM pings through Twitter because I have two Twitter accounts and Twitter only allows a phone to be linked to one account at a time. I'm not willing to change which account it's linked to. I tried to work around the Twitter limitation using Google Voice, but they don't support SMS short codes. I'll compromise on the features I want if I can find a free solution that doesn't require me to set up my own server. I do think this is computer related because it will happen on my computer, not on my phone. edit My current setup: Gmail in Firefox 3.0.15 on Windows XP. I use a netbook as my only personal computer. However, if the only way to accomplish this well is to set up my own mail server or something, I would still want to know that.

  Read the article

• disk write cache buffer and separate power supply

  - by HugoRune

  Windows has a setting to turn off the write-cache buffer (see image) Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. Is it feasible and economical to get such a "separate power supply" for the internal sata drives of a non-server PC? Under what name is such a power supply sold? I know that there are UPS devices that can be connected to external drives,but what is required to be able to switch this setting safely on for an internal disk? The setting has different descriptions in different version of windows Windows XP: Enable write caching on the disk This setting enables write caching in Windows to improve disk performance, but a power outage or equipment failure might result in data loss or corruption. Windows Server 2003: Enable write caching on the disk Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows Vista: Enable advanced performance Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows 7 and 8: Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. This article by Raymond Chen has some more detailed information about what the setting does.

  Read the article

• How can I create a separate toolbar from the Task Bar?

  - by Iszi

  In Windows XP, you could separate toolbars from the Task Bar by dragging them to the desktop. They could then be left lying about anywhere on your screen or, my preferred option, docked to any side of the screen. I found this particularly useful to keep a handy list of common phone numbers quickly accessible. I'd create a new toolbar pointing to a custom folder, and put a bunch of dead shortcuts in the folder that had names and numbers as their file names. I'd then dock the toolbar to the left side, set it to auto-hide and always on top (options which could be set separate from the Task Bar as well) and it would be readily available no matter what else I was doing on my system. However, on my Windows 7 system, I seem unable to perform the crucial step of pulling the new toolbar off of the Task Bar. This is of course with the Task Bar "unlocked" so that I can move all my toolbars around. Is there something I'm missing here, or is this a feature that's been disabled in Windows 7? Is there any way to re-enable it, or otherwise achieve similar functionality? I'd rather be able to do this without additional software, if possible.

  Read the article

< Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >