Search Results

Search found 834 results on 34 pages for 'fragment'.

Page 32/34 | < Previous Page | 28 29 30 31 32 33 34  | Next Page >

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• Loaded OBJ Model Will Not Display in OpenGL / C++ Project

  - by Drake Summers

  I have been experimenting with new effects in game development. The programs I have written have been using generic shapes for the visuals. I wanted to test the effects on something a bit more complex, and wrote a resource loader for Wavefront OBJ files. I started with a simple cube in blender, exported it to an OBJ file with just vertices and triangulated faces, and used it to test the resource loader. I could not get the mesh to show up in my application. The loader never gave me any errors, so I wrote a snippet to loop through my vertex and index arrays that were returned from the loader. The data is exactly the way it is supposed to be. So I simplified the OBJ file by editing it directly to just show a front facing square. Still, nothing is displayed in the application. And don't worry, I did check to make sure that I decreased the value of each index by one while importing the OBJ. - BEGIN EDIT I also tested using glDrawArrays(GL_TRIANGLES, 0, 3 ); to draw the first triangle and it worked! So the issue could be in the binding of the VBO/IBO items. END EDIT - INDEX/VERTEX ARRAY OUTPUT: GLOBALS AND INITIALIZATION FUNCTION: GLuint program; GLint attrib_coord3d; std::vector<GLfloat> vertices; std::vector<GLushort> indices; GLuint vertexbuffer, indexbuffer; GLint uniform_mvp; int initialize() { if (loadModel("test.obj", vertices, indices)) { GLfloat myverts[vertices.size()]; copy(vertices.begin(), vertices.end(), myverts); GLushort myinds[indices.size()]; copy(indices.begin(), indices.end(), myinds); glGenBuffers(1, &vertexbuffer); glBindBuffer(GL_ARRAY_BUFFER, vertexbuffer); glBufferData(GL_ARRAY_BUFFER, sizeof(myverts), myverts, GL_STATIC_DRAW); glGenBuffers(1, &indexbuffer); glBindBuffer(GL_ARRAY_BUFFER, indexbuffer); glBufferData(GL_ELEMENT_ARRAY_BUFFER, sizeof(myinds), myinds, GL_STATIC_DRAW); // OUTPUT DATA FROM NEW ARRAYS TO CONSOLE // ERROR HANDLING OMITTED FOR BREVITY } GLint link_result = GL_FALSE; GLuint vert_shader, frag_shader; if ((vert_shader = create_shader("tri.v.glsl", GL_VERTEX_SHADER)) == 0) return 0; if ((frag_shader = create_shader("tri.f.glsl", GL_FRAGMENT_SHADER)) == 0) return 0; program = glCreateProgram(); glAttachShader(program, vert_shader); glAttachShader(program, frag_shader); glLinkProgram(program); glGetProgramiv(program, GL_LINK_STATUS, &link_result); // ERROR HANDLING OMITTED FOR BREVITY const char* attrib_name; attrib_name = "coord3d"; attrib_coord3d = glGetAttribLocation(program, attrib_name); // ERROR HANDLING OMITTED FOR BREVITY const char* uniform_name; uniform_name = "mvp"; uniform_mvp = glGetUniformLocation(program, uniform_name); // ERROR HANDLING OMITTED FOR BREVITY return 1; } RENDERING FUNCTION: glm::mat4 model = glm::translate(glm::mat4(1.0f), glm::vec3(0.0, 0.0, -4.0)); glm::mat4 view = glm::lookAt(glm::vec3(0.0, 0.0, 4.0), glm::vec3(0.0, 0.0, 3.0), glm::vec3(0.0, 1.0, 0.0)); glm::mat4 projection = glm::perspective(45.0f, 1.0f*(screen_width/screen_height), 0.1f, 10.0f); glm::mat4 mvp = projection * view * model; int size; glUseProgram(program); glUniformMatrix4fv(uniform_mvp, 1, GL_FALSE, glm::value_ptr(mvp)); glClearColor(0.5, 0.5, 0.5, 1.0); glClear(GL_COLOR_BUFFER_BIT|GL_DEPTH_BUFFER_BIT); glEnableVertexAttribArray(attrib_coord3d); glBindBuffer(GL_ARRAY_BUFFER, vertexbuffer); glVertexAttribPointer(attrib_coord3d, 3, GL_FLOAT, GL_FALSE, 0, 0); glBindBuffer(GL_ELEMENT_ARRAY_BUFFER, indexbuffer); glGetBufferParameteriv(GL_ELEMENT_ARRAY_BUFFER, GL_BUFFER_SIZE, &size); glDrawElements(GL_TRIANGLES, size/sizeof(GLushort), GL_UNSIGNED_SHORT, 0); glDisableVertexAttribArray(attrib_coord3d); VERTEX SHADER: attribute vec3 coord3d; uniform mat4 mvp; void main(void) { gl_Position = mvp * vec4(coord3d, 1.0); } FRAGMENT SHADER: void main(void) { gl_FragColor[0] = 0.0; gl_FragColor[1] = 0.0; gl_FragColor[2] = 1.0; gl_FragColor[3] = 1.0; } OBJ RESOURCE LOADER: bool loadModel(const char * path, std::vector<GLfloat> &out_vertices, std::vector<GLushort> &out_indices) { std::vector<GLfloat> temp_vertices; std::vector<GLushort> vertexIndices; FILE * file = fopen(path, "r"); // ERROR HANDLING OMITTED FOR BREVITY while(1) { char lineHeader[128]; int res = fscanf(file, "%s", lineHeader); if (res == EOF) { break; } if (strcmp(lineHeader, "v") == 0) { float _x, _y, _z; fscanf(file, "%f %f %f\n", &_x, &_y, &_z ); out_vertices.push_back(_x); out_vertices.push_back(_y); out_vertices.push_back(_z); } else if (strcmp(lineHeader, "f") == 0) { unsigned int vertexIndex[3]; int matches = fscanf(file, "%d %d %d\n", &vertexIndex[0], &vertexIndex[1], &vertexIndex[2]); out_indices.push_back(vertexIndex[0] - 1); out_indices.push_back(vertexIndex[1] - 1); out_indices.push_back(vertexIndex[2] - 1); } else { ... } } // ERROR HANDLING OMITTED FOR BREVITY return true; } I can edit the question to provide any further info you may need. I attempted to provide everything of relevance and omit what may have been unnecessary. I'm hoping this isn't some really poor mistake, because I have been at this for a few days now. If anyone has any suggestions or advice on the matter, I look forward to hearing it. As a final note: I added some arrays into the code with manually entered data, and was able to display meshes by using those arrays instead of the generated ones. I do not understand!

  Read the article

• Simplifying Human Capital Management with Mobile Applications

  - by HCM-Oracle

  By Aaron Green If you're starting to think 'mobility' is a recurring theme in your reading, you'd be right. For those who haven't started to build organisational capabilities to leverage it, it's fair to say you're late to the party. The good news: better late than never. Research firm eMarketer says the worldwide smartphone audience will total 1.75 billion this year, while communications technology and services provider Ericsson suggests smartphones will triple to 5.6 billion globally by 2019. It should be no surprise, smart phone adoption is reaching the farthest corners of the globe; the subsequent impact of enterprise applications enabled by these devices is driving business performance improvement and will continue to do so. Companies using advanced workforce analytics can add significantly to the bottom line, while impacting customer satisfaction, quality and productivity. It's a statement that makes most business leaders sit forward in their chairs. Achieving these three standards is like sipping The Golden Elixir for the business world. No-one would argue their importance. So what are 'advanced workforce analytics?' Simply, they're unprecedented access to workforce trends and performance markers. Many are made possible by a mobile world and the enterprise applications that come with it on smart devices. Some refer to it as 'the consumerisation of IT'. As this phenomenon has matured and become more widely appreciated it has impacted the spectrum of functional units within an enterprise differently, but powerfully. Whether it's sales, HR, marketing, IT, or operations, all have benefited from a more mobile approach. It has been the catalyst for improvement in, and management of, the employee experience. The net result of which is happier customers. The obvious benefits but the lesser realised impact Most people understand that mobility allows for greater efficiency and productivity, collaboration and flexibility, but how that translates into business outcomes within the various functional groups is lesser known. In actuality mobility has helped galvanise partnerships between cross-functional groups within the enterprise. Where in some quarters it was once feared mobility could fragment a workforce, its rallying cry of support is coming from what you might describe as an unlikely source - HR. As the bedrock of an enterprise, it is conceivable HR might contemplate the possible negative impact of a mobile workforce that no-longer sits in an office, at the same desks every day. After all, who would know what they were doing or saying? How would they collaborate? It's reasonable to see why HR might have a legitimate claim to try and retain as much 'perceived control' as possible. The reality however is mobility has emancipated human capital and its management. Mobility and enterprise applications are expediting decision making. Google calls it Zero Moment of Truth, or ZMOT. It enables smoother operation and can contribute to faster growth. From a collaborative perspective, with the growing use of enterprise social media, which in many cases is being driven by HR, workforce planning and the tangible impact of change is much easier to map. This in turn provides a platform from which individuals and teams can thrive. With more agility and ability to anticipate, staff satisfaction and retention is higher, and real time feedback constant. The management team can save time, energy and costs with more accurate data, which is then intelligently applied across the workforce to truly engage with staff, customers and partners. From a human capital management (HCM) perspective, mobility can help you close the loop on true talent management. It can enhance what managers can offer and what employees can provide in return. It can create nested relationships and powerful partnerships. IT and HR - partners and stewards of mobility One effect of enterprise mobility is an evolution in the nature of the relationship between HR and IT from one of service provision to partnership. The reason for the dynamic shift is largely due to the 'bring your own device' (BYOD) movement, which is transitioning to a 'bring your own application' (BYOA) scenario. As enterprise technology has in some ways reverse-engineered its solutions to help manage this situation, the partnership between IT (the functional owner) and HR (the strategic enabler) is deeply entrenched. And it has to be. The CIO and the HR leader are faced with compliance and regulatory issues and concerns around information security and personal privacy on a daily basis, complicated by global reach and varied domestic legislation. There are tens of thousands of new mobile apps entering the market each month and, unlike many consumer applications which get downloaded but are often never opened again after initial perusal, enterprise applications are being relied upon by functional groups, not least by HR to enhance people management. It requires a systematic approach across all applications in use within the enterprise in order to ensure they're used to best effect. No turning back, and no desire to With real time analytics on performance and the ability for immediate feedback, there is no turning back for managers. In my experience with Oracle, our customers' operational efficiency is at record levels. It's clear as a result of the combination of individual KPIs and organisational goals, CIOs have been able to give HR leaders the ability to build predictive models that feed into an enterprise organisations' evolving strategy. It also helps them ensure regulatory compliance much more easily. Once an arduous task, with mobile enabled automation and quality data, compliance is simpler. Their world has changed for the better. For the CIO, mobility also assists them to optimise performance. While it doesn't come without challenges, mobile-enabled applications and the native experience users have with them means employees don't need high-level technical expertise to train users. It reduces the training and engagement required from the IT team so they can focus on other things that deliver value to the bottom line; all the while lowering the cost of assets and related maintenance work by simplifying processes. Rewards of a mobile enterprise outweigh risks With mobile tools allowing us to increasingly integrate our personal and professional lives, terms like "office hours" are becoming irrelevant, so work/life balance is a cultural must. Enterprises are expected to offer tools that enable workers to access information from anywhere, at any time, from any device. Employees want simplicity and convenience but it doesn't stop at private enterprise. This is a societal shift. Governments, which traditionally have been known to be slower to adopt newer technology, are also offering support for local businesses to go mobile. Several state government websites have advice on how to create mobile apps and more. And as recently as last week the Victorian Minister for Technology Gordon Rich-Phillips unveiled his State government's ICT roadmap for the next two years, which details an increased use of the public cloud, as well as mobile communications, and improved access to online data-sets. Tech giants are investing significantly in solutions designed to simplify mobile deployment and enablement. The mobility trend is creating a wave of change in the industry and driving transformation in the enterprise. If you're not on that wave, the business risk continues to rise as your competitiveness drops. Aaron is the Vice President of HCM Strategy at Oracle Corporation where he is responsible for researching and identifying emerging trends in the practice of Human Resources and works to deliver industry-leading technology solutions. Other responsibilities include, ownership of Oracle's innovative HCM solutions across JAPAC and enabling organisations to transform and modernise their workforce tools. Follow him on Twitter @aaronjgreen

  Read the article

• Making Those PanelBoxes Behave

  - by Duncan Mills

  I have a little problem to solve earlier this week - misbehaving <af:panelBox> components... What do I mean by that? Well here's the scenario, I have a page fragment containing a set of panelBoxes arranged vertically. As it happens, they are stamped out in a loop but that does not really matter. What I want to be able to do is to provide the user with a simple UI to close and open all of the panelBoxes in concert. This could also apply to showDetailHeader and similar items with a disclosed attrubute, but in this case it's good old panelBoxes.  Ok, so the basic solution to this should be self evident. I can set up a suitable scoped managed bean that the panelBoxes all refer to for their disclosed attribute state. Then the open all / close commandButtons in the UI can simply set the state of that bean for all the panelBoxes to pick up via EL on their disclosed attribute. Sound OK? Well that works basically without a hitch, but turns out that there is a slight problem and this is where the framework is attempting to be a little too helpful. The issue is that is the user manually discloses or hides a panelBox then that will override the value that the EL is setting. So for example. I start the page with all panelBoxes collapsed, all set by the EL state I'm storing on the session I manually disclose panelBox no 1. I press the Expand All button - all works as you would hope and all the panelBoxes are now disclosed, including of course panelBox 1 which I just expanded manually. Finally I press the Collapse All button and everything collapses except that first panelBox that I manually disclosed.  The problem is that the component remembers this manual disclosure and that overrides the value provided by the expression. If I change the viewId (navigate away and back) then the panelBox will start to behave again, until of course I touch it again! Now, the more astute amoungst you would think (as I did) Ah, sound like the MDS personalizaton stuff is getting in the way and the solution should simply be to set the dontPersist attribute to disclosed | ALL. Alas this does not fix the issue.  After a little noodling on the best way to approach this I came up with a solution that works well, although if you think of an alternative way do let me know. The principle is simple. In the disclosureListener for the panelBox I take a note of the clientID of the panelBox component that has been touched by the user along with the state. This all gets stored in a Map of Booleans in ViewScope which is keyed by clientID and stores the current disclosed state in the Boolean value.  The listener looks like this (it's held in a request scope backing bean for the page): public void handlePBDisclosureEvent(DisclosureEvent disclosureEvent) { String clientId = disclosureEvent.getComponent().getClientId(FacesContext.getCurrentInstance()); boolean state = disclosureEvent.isExpanded(); pbState.addTouchedPanelBox(clientId, state); } The pbState variable referenced here is a reference to the bean which will hold the state of the panelBoxes that lives in viewScope (recall that everything is re-set when the viewid is changed so keeping this in viewScope is just fine and cleans things up automatically). The addTouchedPanelBox() method looks like this: public void addTouchedPanelBox(String clientId, boolean state) { //create the cache if needed this is just a Map<String,Boolean> if (_touchedPanelBoxState == null) { _touchedPanelBoxState = new HashMap<String, Boolean>(); } // Simply put / replace _touchedPanelBoxState.put(clientId, state); } So that's the first part, we now have a record of every panelBox that the user has touched. So what do we do when the Collapse All or Expand All buttons are pressed? Here we do some JavaScript magic. Basically for each clientID that we have stored away, we issue a client side disclosure event from JavaScript - just as if the user had gone back and changed it manually. So here's the Collapse All button action: public String CloseAllAction() { submitDiscloseOverride(pbState.getTouchedClientIds(true), false); _uiManager.closeAllBoxes(); return null; }  The _uiManager.closeAllBoxes() method is just manipulating the master-state that all of the panelBoxes are bound to using EL. The interesting bit though is the line:  submitDiscloseOverride(pbState.getTouchedClientIds(true), false); To break that down, the first part is a call to that viewScoped state holder to ask for a list of clientIDs that need to be "tweaked": public String getTouchedClientIds(boolean targetState) { StringBuilder sb = new StringBuilder(); if (_touchedPanelBoxState != null && _touchedPanelBoxState.size() > 0) { for (Map.Entry<String, Boolean> entry : _touchedPanelBoxState.entrySet()) { if (entry.getValue() == targetState) { if (sb.length() > 0) { sb.append(','); } sb.append(entry.getKey()); } } } return sb.toString(); } You'll notice that this method only processes those panelBoxes that will be in the wrong state and returns those as a comma separated list. This is then processed by the submitDiscloseOverride() method: private void submitDiscloseOverride(String clientIdList, boolean targetDisclosureState) { if (clientIdList != null && clientIdList.length() > 0) { FacesContext fctx = FacesContext.getCurrentInstance(); StringBuilder script = new StringBuilder(); script.append("overrideDiscloseHandler('"); script.append(clientIdList); script.append("',"); script.append(targetDisclosureState); script.append(");"); Service.getRenderKitService(fctx, ExtendedRenderKitService.class).addScript(fctx, script.toString()); } } This method constructs a JavaScript command to call a routine called overrideDiscloseHandler() in a script attached to the page (using the standard <af:resource> tag). That method parses out the list of clientIDs and sends the correct message to each one: function overrideDiscloseHandler(clientIdList, newState) { AdfLogger.LOGGER.logMessage(AdfLogger.INFO, "Disclosure Hander newState " + newState + " Called with: " + clientIdList); //Parse out the list of clientIds var clientIdArray = clientIdList.split(','); for (var i = 0; i < clientIdArray.length; i++){ var panelBox = flipPanel = AdfPage.PAGE.findComponentByAbsoluteId(clientIdArray[i]); if (panelBox.getComponentType() == "oracle.adf.RichPanelBox"){ panelBox.broadcast(new AdfDisclosureEvent(panelBox, newState)); } }  }  So there you go. You can see how, with a few tweaks the same code could be used for other components with disclosure that might suffer from the same problem, although I'd point out that the behavior I'm working around here us usually desirable. You can download the running example (11.1.2.2) from here. 

  Read the article

• WiX 3 Tutorial: Understanding main WXS and WXI file

  - by Mladen Prajdic

  In the previous post we’ve taken a look at the WiX solution/project structure and project properties. We’re still playing with our super SuperForm application and today we’ll take a look at the general parts of the main wxs file, SuperForm.wxs, and the wxi include file. For wxs file we’ll just go over the general description of what each part does in the code comments. The more detailed descriptions will be in future posts about features themselves. WXI include file Include files are exactly what their name implies. To include a wxi file into the wxs file you have to put the wxi at the beginning of each .wxs file you wish to include it in. If you’ve ever worked with C++ you can think of the include files as .h files. For example if you include SuperFormVariables.wxi into the SuperForm.wxs, the variables in the wxi won’t be seen in FilesFragment.wxs or RegistryFragment.wxs. You’d have to include it manually into those two wxs files too. For preprocessor variable $(var.VariableName) to be seen by every file in the project you have to include them in the WiX project properties->Build->“Define preprocessor variables” textbox. This is why I’ve chosen not to go this route because in multi developer teams not everyone has the same directory structure and having a single variable would mean each developer would have to checkout the wixproj file to edit the variable. This is pretty much unacceptable by my standards. This is why we’ve added a System Environment variable named SuperFormFilesDir as is shown in the previous Wix Tutorial post. Because the FilesFragment.wxs is autogenerated on every project build we don’t want to change it manually each time by adding the include wxi at the beginning of the file. This way we couldn’t recreate it in each pre-build event. <?xml version="1.0" encoding="utf-8"?><Include> <!-- Versioning. These have to be changed for upgrades. It's not enough to just include newer files. --> <?define MajorVersion="1" ?> <?define MinorVersion="0" ?> <?define BuildVersion="0" ?> <!-- Revision is NOT used by WiX in the upgrade procedure --> <?define Revision="0" ?> <!-- Full version number to display --> <?define VersionNumber="$(var.MajorVersion).$(var.MinorVersion).$(var.BuildVersion).$(var.Revision)" ?> <!-- Upgrade code HAS to be the same for all updates. Once you've chosen it don't change it. --> <?define UpgradeCode="YOUR-GUID-HERE" ?> <!-- Path to the resources directory. resources don't really need to be included in the project structure but I like to include them for for clarity --> <?define ResourcesDir="$(var.ProjectDir)\Resources" ?> <!-- The name of your application exe file. This will be used to kill the process when updating and creating the desktop shortcut --> <?define ExeProcessName="SuperForm.MainApp.exe" ?></Include> For now there’s no way to tell WiX in Visual Studio to have a wxi include file available to the whole project, so you have to include it in each file separately. Only variables set in “Define preprocessor variables” or System Environment variables are accessible to the whole project for now. The main WXS file: SuperForm.wxs We’ll only take a look at the general structure of the main SuperForm.wxs and not its the details. We’ll cover the details in future posts. The code comments should provide plenty info about what each part does in general. Basically there are 5 major parts. The update part, the conditions and actions part, the UI install sequence, the directory structure and the features we want to include. <?xml version="1.0" encoding="UTF-8"?><!-- Add xmlns:util namespace definition to be able to use stuff from WixUtilExtension dll--><Wix xmlns="http://schemas.microsoft.com/wix/2006/wi" xmlns:util="http://schemas.microsoft.com/wix/UtilExtension"> <!-- This is how we include wxi files --> <?include $(sys.CURRENTDIR)Includes\SuperFormVariables.wxi ?> <!-- Id="*" is to enable upgrading. * means that the product ID will be autogenerated on each build. Name is made of localized product name and version number. --> <Product Id="*" Name="!(loc.ProductName) $(var.VersionNumber)" Language="!(loc.LANG)" Version="$(var.VersionNumber)" Manufacturer="!(loc.ManufacturerName)" UpgradeCode="$(var.UpgradeCode)"> <!-- Define the minimum supported installer version (3.0) and that the install should be done for the whole machine not just the current user --> <Package InstallerVersion="300" Compressed="yes" InstallScope="perMachine"/> <Media Id="1" Cabinet="media1.cab" EmbedCab="yes" /> <!-- Upgrade settings. This will be explained in more detail in a future post --> <Upgrade Id="$(var.UpgradeCode)"> <UpgradeVersion OnlyDetect="yes" Minimum="$(var.VersionNumber)" IncludeMinimum="no" Property="NEWER_VERSION_FOUND" /> <UpgradeVersion Minimum="0.0.0.0" IncludeMinimum="yes" Maximum="$(var.VersionNumber)" IncludeMaximum="no" Property="OLDER_VERSION_FOUND" /> </Upgrade> <!-- Reference the global NETFRAMEWORK35 property to check if it exists --> <PropertyRef Id="NETFRAMEWORK35"/> <!-- Startup conditions that checks if .Net Framework 3.5 is installed or if we're running the OS higher than Windows XP SP2. If not the installation is aborted. By doing the (Installed OR ...) property means that this condition will only be evaluated if the app is being installed and not on uninstall or changing --> <Condition Message="!(loc.DotNetFrameworkNeeded)"> <![CDATA[Installed OR NETFRAMEWORK35]]> </Condition> <Condition Message="!(loc.AppNotSupported)"> <![CDATA[Installed OR ((VersionNT >= 501 AND ServicePackLevel >= 2) OR (VersionNT >= 502))]]> </Condition> <!-- This custom action in the InstallExecuteSequence is needed to stop silent install (passing /qb to msiexec) from going around it. --> <CustomAction Id="NewerVersionFound" Error="!(loc.SuperFormNewerVersionInstalled)" /> <InstallExecuteSequence> <!-- Check for newer versions with FindRelatedProducts and execute the custom action after it --> <Custom Action="NewerVersionFound" After="FindRelatedProducts"> <![CDATA[NEWER_VERSION_FOUND]]> </Custom> <!-- Remove the previous versions of the product --> <RemoveExistingProducts After="InstallInitialize"/> <!-- WixCloseApplications is a built in custom action that uses util:CloseApplication below --> <Custom Action="WixCloseApplications" Before="InstallInitialize" /> </InstallExecuteSequence> <!-- This will ask the user to close the SuperForm app if it's running while upgrading --> <util:CloseApplication Id="CloseSuperForm" CloseMessage="no" Description="!(loc.MustCloseSuperForm)" ElevatedCloseMessage="no" RebootPrompt="no" Target="$(var.ExeProcessName)" /> <!-- Use the built in WixUI_InstallDir GUI --> <UIRef Id="WixUI_InstallDir" /> <UI> <!-- These dialog references are needed for CloseApplication above to work correctly --> <DialogRef Id="FilesInUse" /> <DialogRef Id="MsiRMFilesInUse" /> <!-- Here we'll add the GUI logic for installation and updating in a future post--> </UI> <!-- Set the icon to show next to the program name in Add/Remove programs --> <Icon Id="SuperFormIcon.ico" SourceFile="$(var.ResourcesDir)\Exclam.ico" /> <Property Id="ARPPRODUCTICON" Value="SuperFormIcon.ico" /> <!-- Installer UI custom pictures. File names are made up. Add path to your pics. –> <!-- <WixVariable Id="WixUIDialogBmp" Value="MyAppLogo.jpg" /> <WixVariable Id="WixUIBannerBmp" Value="installBanner.jpg" /> --> <!-- the default directory structure --> <Directory Id="TARGETDIR" Name="SourceDir"> <Directory Id="ProgramFilesFolder"> <Directory Id="INSTALLLOCATION" Name="!(loc.ProductName)" /> </Directory> </Directory> <!-- Set the default install location to the value of INSTALLLOCATION (usually c:\Program Files\YourProductName) --> <Property Id="WIXUI_INSTALLDIR" Value="INSTALLLOCATION" /> <!-- Set the components defined in our fragment files that will be used for our feature --> <Feature Id="SuperFormFeature" Title="!(loc.ProductName)" Level="1"> <ComponentGroupRef Id="SuperFormFiles" /> <ComponentRef Id="cmpVersionInRegistry" /> <ComponentRef Id="cmpIsThisUpdateInRegistry" /> </Feature> </Product></Wix> For more info on what certain attributes mean you should look into the WiX Documentation.   WiX 3 tutorial by Mladen Prajdic navigation WiX 3 Tutorial: Solution/Project structure and Dev resources WiX 3 Tutorial: Understanding main wxs and wxi file WiX 3 Tutorial: Generating file/directory fragments with Heat.exe

  Read the article

• Wireless will not connect

  - by azz0r

  Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

  Read the article

• CodePlex Daily Summary for Monday, April 19, 2010

  CodePlex Daily Summary for Monday, April 19, 2010New Projects8085 Microprocessor simulator: This program allows you to write 8085 programs in assembly and run those programs on your PC. It comes with lots of help, plus you can put breakpo...Additional.NET framework: The Additional.Net framework extends the functionality of the .NET framework for easier application development. It is developed in C#.Astoria Contrib: A contrib project for filling the gaps in WCF Data Services, providing missing functionality or augmenting with T4 templates, helpers, etc.ClipoWeb: ClipoWeb is a web clipboard that allows you to copy text and files between computers. Users access a web page on the source and destination compute...elearning Center: Đây là một ứng dụng web viết hoàn toàn bằng Sliverlight. Ứng dụng này là một dạng elearning với đầy đủ chức năng và có khả năng tương tác tối đa v...Excel VSTO SQL Server Browser: Get Data from SQL Server and put it in Excel directly. The objective is to get more control about what do you need to pull and create automatic pro...Generic Tree Structure: Generic Base Classes that helps you to create complex tree structures without writing it again and again. Simply to use Like "var Node<Folder> fold...LAN Lordz LAN Party System: The LAN Lordz LAN Party System makes it easier for medium and large size events to track their attendance, sponsors, door prizes, tournaments, and...LiteFx: O LiteFx é um framework que ajuda na implementação de DDD (anêmico ou rico) ele foi desenvolvido por Douglas Aguiar (http://twitter.com/DouglasAgui...Managed UI Flow for ASP.NET MVC Framework: If your web application getting more complex, understanding and managing of complex UI flows(pageflow of application) getting harder and harder, If...Meus Exemplos: Meus ExemplosOrchard Blueprint Theme: Orchard BluePrint is a project that provides a WYSIWYG reference implementation of a Orchard theme to help designers get started with theme design....Outlook Social Network Connector - Avatar: Avatar 是一个开源的MS Outlook的插件，豆瓣用户可以在Outlook 2010中使用豆瓣。查看一封邮件中相关的收件人、发件人的用户广播、同城活动以及豆邮。不用上豆瓣也能方便了解好友动态。这个插件使用C#， .NET 4.0 开发。API 请求认证使用OAuth 认证。 (Avat...Quadro Tree: This is Quadri tree library.Sharepoint 2010 Alert Controller: In MOSS 2007 or Sharepoint Server 2010 if you want to see your alerts by list name you should use this tool.SharePoint Web Parts: The goal of this project is to develop a set of web parts for SharePoint.Silverlight Image Cropper: This is a silverlight 4 util that makes it easy to crop out a number images of a specific resolution screen or screens. ie. an easy way to crop ...SilverlightFTP: Silverlight ftp clientsplibex: libraries for sharepoint lists manipulationStardustExtensions: Official Extensions for StardustSwim Team Manager: Swim Team Manager is designed for managing and tracking administrative and performance information for your club, school, or swim team. Swim Tea...ToDoListWpf: A To Do List, I used it to manage my work items. I am sorry for my poor English.Trance Layer: TranceLayer is a fast and flexible logging or diagnostics framework for .Net. It allows you to plug it into an existing or new application with m...Unoficcial NeoFM.hu NowPlaying: A little windows tray program. Shows what's on neofm.hu right now.WabbitStudio Z80 Software Tools: The software suite provides all of the tools you need to create high quality Z80 software in Z80 assembly language, with a focus on TI calculators....WinToolbar: Windows.Toolbar is Silverlight library that implements common widgets that allows us to build a rich toolbar control in our applications, it incor...XP-More: XP-More is a tool that helps manage Windows 7 Virtual Machines (XP Mode and any other). Specifically, it makes duplication of VMs a no brainer - no...Yodelay .NET Framework Extensions: The Yodelay .NET Framework Extensions project provides a library of components that make many kinds of programming tasks simpler. These include bas...New ReleasesClipoWeb: ClipoWeb 1.0: First Beta release of the ClipoWeb web applicationDDDSample.Net: 0.8: This release contains all four versions of DDDSample.Net available in previous, 0.7 and a brand new one: Layered Model version. Layered Model demon...DotNetNuke Blueprint: 00.00.02: Added to this version CSS Reset Skin version including Grids This version will soon be updated with corresponding HTML version and DNN templateEsferatec.Text.RegularExpressions: 3.5.1003.1001: first stable release of the class; the assembly file is ready to use, the documentation is complete;Excel VSTO SQL Server Browser: Sample Only: Sample without Ribbon UI, if you close the TaskPane you will no longer able to open it without restart ExcelFolder Bookmarks: Folder Bookmarks 1.5.5: This is the latest version of Folder Bookmarks (1.5.5), with the new Archive Manager and Archive Viewer. It has an installer - it will create a dir...Gardens Point LEX: Gardens Point LEX, Version 1.1.3: The main distribution is a zip file. This contains the binary executable, documentation, source code and the examples. ChangesVersion 1.1.3 corre...Gardens Point Parser Generator: Gardens Point Parser Generator V1.4.0: The distribution is a zip archive which contains the binary executables, documentation, source code and examples. ChangesVersion 1.4.0 of GPPG has...HKGolden Express: HKGoldenExpress (Build 201004181455): New features: Added rating of each topic. (Note: This feature is availabe since Build 201004172120) Bug fix: Handle invalid XML character in XML...Home Access Plus+: v4.0.0.0 Beta: v4.0.0.0 Beta Change Log: Moved to using .net 4.0 New Silverlight Uploader Various .net 4 fixes and tweaks File Changes: All fixes have changedHTML Ruby: 6.21.6: Reduced performance hit on pages with heavy DOM manipulations Fixed issue where empty tags caused it to apply invalid spacing values Stop spaci...LINQ to VFP: LinqToVfp (v1.0.17.2): Modified to allow using RecNo as a primary key. This build requires IQToolkit v0.17b.Managed UI Flow for ASP.NET MVC Framework: Preview 1: The source available on this site, does not reflect the final state of the project, it is a preview of what will be shipping in the framework in th...MVVM Light Toolkit: MVVM Light Toolkit V3 SP1 (2): Super minor update to accommodate the new Blend 4 RC. Only changes: The path to the Blend 4 templates changed to be "My Documents\Expression\Blend...N2 CMS: 2.0 rc: N2 is a lightweight CMS framework for ASP.NET. It helps you build great web sites that anyone can update. Major Changes (1.5 -> 2.0 release candid...OpenGL ES 2.0 Compact Framework Wrapper: Sample application CAB with texturing: This took some time as it was pretty hard to get the texture loaded and setup so that it would bind to the sampler2D in the fragment shader. Featu...Orchard Blueprint Theme: 00.00.01: This is the first release of this project, still in a very alpha version. Very soon this release is to be updated with the HTML version of the them...RoughJs: RoughJsSL: This is Silverlight library's CompilerSharepoint 2010 Alert Controller: Sharepoint 2010 Alert Controller: After you download WSP file you can get help from Home PageSharePoint LogViewer: SharePoint LogViewer 2.5: Minimize log viewer to tray Get popup notification of SharePoint log events from tray Redirect log entries to event log Send email notifications on...Site Directory for SharePoint 2010 (from Microsoft Consulting Services, UK): v1.1: This is a minor update which includes the following changes: Code consolidation across the whole project Additional site data captured. See solut...Stardust: Stardust 1.0: First stable version of Stardust (Build 172)StardustExtensions: Facebook Extension: Extension for stardust to upload and post images on Facebook.StardustExtensions: Facebook Extension (Source): The source code of an extension for Stardust used to post images on facebook.StardustExtensions: WPF Example: This is an example extension. Uses WPF to create a Window and say "Hello World!" Is a perfect download if want to start writing Stardust ExtensionsStardustExtensions: WPF Example Source: This is the source code of an extension that creates a Window using WPF & displays a simple text. Is great as an example of creating Stardust Exten...TFTP Server: TFTP Server 1.1 Beta installer: New MSI based installer Installs a TFTP service Supports multiple servers on different endpoints, with every server pointing to its own root di...TiledLib: TiledLib 1.1: This download is for prebuilt DLLs and a demo project. For the full source code, use the Source Code tab. Changes: Bug fixes in a few methods Ad...Trance Layer: TranceLayer Digger: Digger version is a beta. It is intended to be used as a demonstration of muscles while lacking a set of features that are in the docs. The set of ...uManage - Active Directory Self-Service Portal: uManage v1.2 (.NET 4.0 RTM): New Releasev1.2 Adds the Administrative Portal as well as the requirement of a MSSQL database (2005+). The Setup Wizard has also been updated to i...Unoficcial NeoFM.hu NowPlaying: NeoNotifier: First release. Aplha, but usable.VidCoder: 0.2.1: Changes: Added 2-pass encoding Fixed x264 options getting mangled during p-invoke Fixed intermittent crash with logging window open due to thre...WCF RIA Services Contrib: WCF RIA Services Contrib RC2 Release: This version is for the WCF RIA Services RC2 (SL4 RTM) release. The ApplyState has been modifed in this version to disable validation during proces...WiiCIS.NET: WiiCIS.NET v0.2: Changes... - Removal of WiimoteManager, connection must be done manually - Accelerometer orientation was originally in degrees, is now in radians -...WinToolbar: WinToolbar Source code plus sample: This zip file contains the current version source code and libraries plus a testrunner (sample app).XP-More: 0.9 (Beta): Most of the functionality is in place, final polishing will be done soon.Most Popular ProjectsFacebook Developer ToolkitWSPBuilder (SharePoint WSP tool)QuickGraph, Graph Data Structures And Algorithms for .NetPerformance Analysis of Logs (PAL) Toolpatterns & practices: Team Development with Visual Studio Team Foundation ServerTFS Integration Platformpatterns & practices: Performance Testing Guidance for Web Applicationspatterns & practices: Enterprise Library ContribJSON ViewerManaged Wifi APIMost Active ProjectsRawrpatterns & practices – Enterprise LibraryIndustrial DashboardIonics Isapi Rewrite FilterFarseer Physics EngineMVVM Light ToolkitjQuery Library for SharePoint Web ServicesN2 CMSCaliburn: An Application Framework for WPF and SilverlightBlogEngine.NET

  Read the article

• So…is it a Seek or a Scan?

  - by Paul White

  You’re probably most familiar with the terms ‘Seek’ and ‘Scan’ from the graphical plans produced by SQL Server Management Studio (SSMS).  The image to the left shows the most common ones, with the three types of scan at the top, followed by four types of seek.  You might look to the SSMS tool-tip descriptions to explain the differences between them: Not hugely helpful are they?  Both mention scans and ranges (nothing about seeks) and the Index Seek description implies that it will not scan the index entirely (which isn’t necessarily true). Recall also yesterday’s post where we saw two Clustered Index Seek operations doing very different things.  The first Seek performed 63 single-row seeking operations; and the second performed a ‘Range Scan’ (more on those later in this post).  I hope you agree that those were two very different operations, and perhaps you are wondering why there aren’t different graphical plan icons for Range Scans and Seeks?  I have often wondered about that, and the first person to mention it after yesterday’s post was Erin Stellato (twitter | blog): Before we go on to make sense of all this, let’s look at another example of how SQL Server confusingly mixes the terms ‘Scan’ and ‘Seek’ in different contexts.  The diagram below shows a very simple heap table with two columns, one of which is the non-clustered Primary Key, and the other has a non-unique non-clustered index defined on it.  The right hand side of the diagram shows a simple query, it’s associated query plan, and a couple of extracts from the SSMS tool-tip and Properties windows. Notice the ‘scan direction’ entry in the Properties window snippet.  Is this a seek or a scan?  The different references to Scans and Seeks are even more pronounced in the XML plan output that the graphical plan is based on.  This fragment is what lies behind the single Index Seek icon shown above: You’ll find the same confusing references to Seeks and Scans throughout the product and its documentation. Making Sense of Seeks Let’s forget all about scans for a moment, and think purely about seeks.  Loosely speaking, a seek is the process of navigating an index B-tree to find a particular index record, most often at the leaf level.  A seek starts at the root and navigates down through the levels of the index to find the point of interest: Singleton Lookups The simplest sort of seek predicate performs this traversal to find (at most) a single record.  This is the case when we search for a single value using a unique index and an equality predicate.  It should be readily apparent that this type of search will either find one record, or none at all.  This operation is known as a singleton lookup.  Given the example table from before, the following query is an example of a singleton lookup seek: Sadly, there’s nothing in the graphical plan or XML output to show that this is a singleton lookup – you have to infer it from the fact that this is a single-value equality seek on a unique index.  The other common examples of a singleton lookup are bookmark lookups – both the RID and Key Lookup forms are singleton lookups (an RID lookup finds a single record in a heap from the unique row locator, and a Key Lookup does much the same thing on a clustered table).  If you happen to run your query with STATISTICS IO ON, you will notice that ‘Scan Count’ is always zero for a singleton lookup. Range Scans The other type of seek predicate is a ‘seek plus range scan’, which I will refer to simply as a range scan.  The seek operation makes an initial descent into the index structure to find the first leaf row that qualifies, and then performs a range scan (either backwards or forwards in the index) until it reaches the end of the scan range. The ability of a range scan to proceed in either direction comes about because index pages at the same level are connected by a doubly-linked list – each page has a pointer to the previous page (in logical key order) as well as a pointer to the following page.  The doubly-linked list is represented by the green and red dotted arrows in the index diagram presented earlier.  One subtle (but important) point is that the notion of a ‘forward’ or ‘backward’ scan applies to the logical key order defined when the index was built.  In the present case, the non-clustered primary key index was created as follows: CREATE TABLE dbo.Example ( key_col INTEGER NOT NULL, data INTEGER NOT NULL, CONSTRAINT [PK dbo.Example key_col] PRIMARY KEY NONCLUSTERED (key_col ASC) ) ; Notice that the primary key index specifies an ascending sort order for the single key column.  This means that a forward scan of the index will retrieve keys in ascending order, while a backward scan would retrieve keys in descending key order.  If the index had been created instead on key_col DESC, a forward scan would retrieve keys in descending order, and a backward scan would return keys in ascending order. A range scan seek predicate may have a Start condition, an End condition, or both.  Where one is missing, the scan starts (or ends) at one extreme end of the index, depending on the scan direction.  Some examples might help clarify that: the following diagram shows four queries, each of which performs a single seek against a column holding every integer from 1 to 100 inclusive.  The results from each query are shown in the blue columns, and relevant attributes from the Properties window appear on the right: Query 1 specifies that all key_col values less than 5 should be returned in ascending order.  The query plan achieves this by seeking to the start of the index leaf (there is no explicit starting value) and scanning forward until the End condition (key_col < 5) is no longer satisfied (SQL Server knows it can stop looking as soon as it finds a key_col value that isn’t less than 5 because all later index entries are guaranteed to sort higher). Query 2 asks for key_col values greater than 95, in descending order.  SQL Server returns these results by seeking to the end of the index, and scanning backwards (in descending key order) until it comes across a row that isn’t greater than 95.  Sharp-eyed readers may notice that the end-of-scan condition is shown as a Start range value.  This is a bug in the XML show plan which bubbles up to the Properties window – when a backward scan is performed, the roles of the Start and End values are reversed, but the plan does not reflect that.  Oh well. Query 3 looks for key_col values that are greater than or equal to 10, and less than 15, in ascending order.  This time, SQL Server seeks to the first index record that matches the Start condition (key_col >= 10) and then scans forward through the leaf pages until the End condition (key_col < 15) is no longer met. Query 4 performs much the same sort of operation as Query 3, but requests the output in descending order.  Again, we have to mentally reverse the Start and End conditions because of the bug, but otherwise the process is the same as always: SQL Server finds the highest-sorting record that meets the condition ‘key_col < 25’ and scans backward until ‘key_col >= 20’ is no longer true. One final point to note: seek operations always have the Ordered: True attribute.  This means that the operator always produces rows in a sorted order, either ascending or descending depending on how the index was defined, and whether the scan part of the operation is forward or backward.  You cannot rely on this sort order in your queries of course (you must always specify an ORDER BY clause if order is important) but SQL Server can make use of the sort order internally.  In the four queries above, the query optimizer was able to avoid an explicit Sort operator to honour the ORDER BY clause, for example. Multiple Seek Predicates As we saw yesterday, a single index seek plan operator can contain one or more seek predicates.  These seek predicates can either be all singleton seeks or all range scans – SQL Server does not mix them.  For example, you might expect the following query to contain two seek predicates, a singleton seek to find the single record in the unique index where key_col = 10, and a range scan to find the key_col values between 15 and 20: SELECT key_col FROM dbo.Example WHERE key_col = 10 OR key_col BETWEEN 15 AND 20 ORDER BY key_col ASC ; In fact, SQL Server transforms the singleton seek (key_col = 10) to the equivalent range scan, Start:[key_col >= 10], End:[key_col <= 10].  This allows both range scans to be evaluated by a single seek operator.  To be clear, this query results in two range scans: one from 10 to 10, and one from 15 to 20. Final Thoughts That’s it for today – tomorrow we’ll look at monitoring singleton lookups and range scans, and I’ll show you a seek on a heap table. Yes, a seek.  On a heap.  Not an index! If you would like to run the queries in this post for yourself, there’s a script below.  Thanks for reading! IF OBJECT_ID(N'dbo.Example', N'U') IS NOT NULL BEGIN DROP TABLE dbo.Example; END ; -- Test table is a heap -- Non-clustered primary key on 'key_col' CREATE TABLE dbo.Example ( key_col INTEGER NOT NULL, data INTEGER NOT NULL, CONSTRAINT [PK dbo.Example key_col] PRIMARY KEY NONCLUSTERED (key_col) ) ; -- Non-unique non-clustered index on the 'data' column CREATE NONCLUSTERED INDEX [IX dbo.Example data] ON dbo.Example (data) ; -- Add 100 rows INSERT dbo.Example WITH (TABLOCKX) ( key_col, data ) SELECT key_col = V.number, data = V.number FROM master.dbo.spt_values AS V WHERE V.[type] = N'P' AND V.number BETWEEN 1 AND 100 ; -- ================ -- Singleton lookup -- ================ ; -- Single value equality seek in a unique index -- Scan count = 0 when STATISTIS IO is ON -- Check the XML SHOWPLAN SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col = 32 ; -- =========== -- Range Scans -- =========== ; -- Query 1 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col <= 5 ORDER BY E.key_col ASC ; -- Query 2 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col > 95 ORDER BY E.key_col DESC ; -- Query 3 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col >= 10 AND E.key_col < 15 ORDER BY E.key_col ASC ; -- Query 4 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col >= 20 AND E.key_col < 25 ORDER BY E.key_col DESC ; -- Final query (singleton + range = 2 range scans) SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col = 10 OR E.key_col BETWEEN 15 AND 20 ORDER BY E.key_col ASC ; -- === TIDY UP === DROP TABLE dbo.Example; © 2011 Paul White email: [email protected] twitter: @SQL_Kiwi

  Read the article

• wifi not recognized

  - by pumper

  I had wifi and worked then some day ubuntu asked me to update some packeages and restarted the system and after that no wifi. this is my wireless_script output : ########## wireless info START ########## ##### release ##### Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty ##### kernel ##### Linux S510p 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ##### lspci ##### 02:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Lenovo Device [17aa:3026] Kernel driver in use: ath9k 03:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8162 Fast Ethernet [1969:1090] (rev 10) Subsystem: Lenovo Device [17aa:3807] Kernel driver in use: alx ##### lsusb ##### Bus 001 Device 006: ID 0eef:a111 D-WAV Scientific Co., Ltd Bus 001 Device 007: ID 0cf3:3004 Atheros Communications, Inc. Bus 001 Device 004: ID 174f:1488 Syntek Bus 001 Device 003: ID 03f0:5607 Hewlett-Packard Bus 001 Device 002: ID 8087:8000 Intel Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 002: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ##### PCMCIA Card Info ##### ##### rfkill ##### 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no ##### iw reg get ##### country 00: (2402 - 2472 @ 40), (3, 20) (2457 - 2482 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS (2474 - 2494 @ 20), (3, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS (5170 - 5250 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS (5735 - 5835 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS ##### interfaces ##### # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig wlan0 up # line maintained by pppoeconf provider dsl-provider auto wlan0 iface wlan0 inet manual ##### iwconfig ##### wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off ##### route ##### Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface ##### resolv.conf ##### ##### nm-tool ##### NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: alx State: unavailable Default: no HW Address: <MAC address removed> Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: unmanaged Default: no HW Address: <MAC address removed> Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points ##### NetworkManager.state ##### [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true ##### NetworkManager.conf ##### [main] plugins=ifupdown,keyfile,ofono dns=dnsmasq no-auto-default=<MAC address removed>, [ifupdown] managed=false ##### iwlist ##### wlan0 Scan completed : Cell 01 - Address: <MAC address removed> Channel:1 Frequency:2.412 GHz (Channel 1) Quality=55/70 Signal level=-55 dBm Encryption key:on ESSID:"mohsen" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000076c342498 Extra: Last beacon: 12ms ago IE: Unknown: 00066D6F6873656E IE: Unknown: 010882848B960C121824 IE: Unknown: 030101 IE: Unknown: 2A0104 IE: Unknown: 32043048606C ##### iwlist channel ##### wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz ##### lsmod ##### ath3k 13318 0 bluetooth 395423 23 bnep,ath3k,btusb,rfcomm ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626489 1 ath9k cfg80211 484040 3 ath,ath9k,mac80211 ##### modinfo ##### filename: /lib/modules/3.13.0-24-generic/kernel/drivers/bluetooth/ath3k.ko firmware: ath3k-1.fw license: GPL version: 1.0 description: Atheros AR30xx firmware driver author: Atheros Communications srcversion: 98A5245588C09E5E41690D0 alias: usb:v0489pE036d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE03Cd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE02Cd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE003d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3121d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3402d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04C5p1330d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE04Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE056d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE04Ed*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3393d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE057d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0220d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0219d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE005d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3362d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3008d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3006d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3005d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3375d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p817Ad*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p311Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3008d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p0036d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v03F0p311Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE027d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE03Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0215d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3304d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE019d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3002d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3000d*dc*dsc*dp*ic*isc*ip*in* depends: bluetooth intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko license: Dual BSD/GPL description: Support for Atheros 802.11n wireless LAN cards. author: Atheros Communications srcversion: BAF225EEB618908380B28DA alias: platform:qca955x_wmac alias: platform:ar934x_wmac alias: platform:ar933x_wmac alias: platform:ath9k alias: pci:v0000168Cd00000036sv*sd*bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd00003027bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002810bc*sc*i* alias: pci:v0000168Cd00000036sv0000144Fsd00007202bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd00002130bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000612bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000652bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000642bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd0000302Cbc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003027bc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Ebc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Dbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Cbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Bbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Abc*sc*i* alias: pci:v0000168Cd00000036sv00001028sd0000020Ebc*sc*i* alias: pci:v0000168Cd00000036sv0000103Csd0000217Fbc*sc*i* alias: pci:v0000168Cd00000036sv0000103Csd000018E3bc*sc*i* alias: pci:v0000168Cd00000036sv000017AAsd00003026bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd0000213Abc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000662bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000672bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000622bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd00003028bc*sc*i* alias: pci:v0000168Cd00000036sv0000105Bsd0000E069bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd0000302Bbc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003026bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003025bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002812bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002811bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00006671bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000632bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd0000A119bc*sc*i* alias: pci:v0000168Cd00000036sv0000105Bsd0000E068bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd00002176bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003028bc*sc*i* alias: pci:v0000168Cd00000037sv*sd*bc*sc*i* alias: pci:v0000168Cd00000034sv*sd*bc*sc*i* alias: pci:v0000168Cd00000034sv000010CFsd00001783bc*sc*i* alias: pci:v0000168Cd00000034sv000014CDsd00000064bc*sc*i* alias: pci:v0000168Cd00000034sv000014CDsd00000063bc*sc*i* alias: pci:v0000168Cd00000034sv0000103Csd00001864bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006641bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006631bc*sc*i* alias: pci:v0000168Cd00000034sv00001043sd0000850Ebc*sc*i* alias: pci:v0000168Cd00000034sv00001A3Bsd00002110bc*sc*i* alias: pci:v0000168Cd00000034sv00001969sd00000091bc*sc*i* alias: pci:v0000168Cd00000034sv000017AAsd00003214bc*sc*i* alias: pci:v0000168Cd00000034sv0000168Csd00003117bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006661bc*sc*i* alias: pci:v0000168Cd00000034sv00001A3Bsd00002116bc*sc*i* alias: pci:v0000168Cd00000033sv*sd*bc*sc*i* alias: pci:v0000168Cd00000032sv*sd*bc*sc*i* alias: pci:v0000168Cd00000032sv00001043sd0000850Dbc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00001C01bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00001C00bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001F95bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001195bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001F86bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001186bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00002001bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00002000bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Fsd00007197bc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E04Fbc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E04Ebc*sc*i* alias: pci:v0000168Cd00000032sv000011ADsd00006628bc*sc*i* alias: pci:v0000168Cd00000032sv000011ADsd00006627bc*sc*i* alias: pci:v0000168Cd00000032sv00001C56sd00004001bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002100bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002C97bc*sc*i* alias: pci:v0000168Cd00000032sv000017AAsd00003219bc*sc*i* alias: pci:v0000168Cd00000032sv000017AAsd00003218bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C708bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C680bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C706bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Fbc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Ebc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Dbc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd00004106bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd00004105bc*sc*i* alias: pci:v0000168Cd00000032sv0000185Fsd00003027bc*sc*i* alias: pci:v0000168Cd00000032sv0000185Fsd00003119bc*sc*i* alias: pci:v0000168Cd00000032sv0000168Csd00003122bc*sc*i* alias: pci:v0000168Cd00000032sv0000168Csd00003119bc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E075bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002152bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd0000126Abc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002126bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001237bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002086bc*sc*i* alias: pci:v0000168Cd00000030sv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Esv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Dsv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Csv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Bsv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Bsv00001A3Bsd00002C37bc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd00001536bc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd0000147Dbc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd0000147Cbc*sc*i* alias: pci:v0000168Cd0000002Asv0000185Fsd0000309Dbc*sc*i* alias: pci:v0000168Cd0000002Asv00001A32sd00000306bc*sc*i* alias: pci:v0000168Cd0000002Asv000011ADsd00006642bc*sc*i* alias: pci:v0000168Cd0000002Asv000011ADsd00006632bc*sc*i* alias: pci:v0000168Cd0000002Asv0000105Bsd0000E01Fbc*sc*i* alias: pci:v0000168Cd0000002Asv00001A3Bsd00001C71bc*sc*i* alias: pci:v0000168Cd0000002Asv*sd*bc*sc*i* alias: pci:v0000168Cd00000029sv*sd*bc*sc*i* alias: pci:v0000168Cd00000027sv*sd*bc*sc*i* alias: pci:v0000168Cd00000024sv*sd*bc*sc*i* alias: pci:v0000168Cd00000023sv*sd*bc*sc*i* depends: ath9k_hw,mac80211,ath9k_common,cfg80211,ath intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 parm: debug:Debugging mask (uint) parm: nohwcrypt:Disable hardware encryption (int) parm: blink:Enable LED blink on activity (int) parm: btcoex_enable:Enable wifi-BT coexistence (int) parm: bt_ant_diversity:Enable WLAN/BT RX antenna diversity (int) parm: ps_enable:Enable WLAN PowerSave (int) filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko license: Dual BSD/GPL description: Shared library for Atheros wireless 802.11n LAN cards. author: Atheros Communications srcversion: 696B00A6C59713EC0966997 depends: ath,ath9k_hw intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko license: Dual BSD/GPL description: Support for Atheros 802.11n wireless LAN cards. author: Atheros Communications srcversion: 4809F3842A0542CD6B556D3 depends: ath intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath.ko license: Dual BSD/GPL description: Shared library for Atheros wireless LAN cards. author: Atheros Communications srcversion: 88A67C5359B02C5A710AFCF depends: cfg80211 intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 ##### modules ##### lp rtc ##### blacklist ##### [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac [/etc/modprobe.d/fbdev-blacklist.conf] blacklist arkfb blacklist aty128fb blacklist atyfb blacklist radeonfb blacklist cirrusfb blacklist cyber2000fb blacklist gx1fb blacklist gxfb blacklist kyrofb blacklist matroxfb_base blacklist mb862xxfb blacklist neofb blacklist nvidiafb blacklist pm2fb blacklist pm3fb blacklist s3fb blacklist savagefb blacklist sisfb blacklist tdfxfb blacklist tridentfb blacklist viafb blacklist vt8623fb ##### udev rules ##### # PCI device 0x1969:0x1090 (alx) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC address removed>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x168c:0x0036 (ath9k) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC address removed>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0" ##### dmesg ##### [ 1.707662] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f03) [ 11.918852] ath: phy0: WB335 1-ANT card detected [ 11.918856] ath: phy0: Set BT/WLAN RX diversity capability [ 11.926438] ath: phy0: Enable LNA combining [ 11.928469] ath: phy0: ASPM enabled: 0x42 [ 11.928473] ath: EEPROM regdomain: 0x65 [ 11.928475] ath: EEPROM indicates we should expect a direct regpair map [ 11.928478] ath: Country alpha2 being used: 00 [ 11.928479] ath: Regpair used: 0x65 [ 14.066021] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready ########## wireless info END ############

  Read the article

• Ubuntu 12.04 + Raid0 + Windows 7 not loading

  - by Douglas

  please someone help me.... (Sorry for my english) Hi, I have a Pc with 2 Hd (1Tb each) on Raid0. I had a Windows 7 64bits working for several months. When I installed the Windows I let a 100Gb partition empty to install Ubuntu someday. I was using Linux on a Virtualbox, but this week I tried to install Ubuntu 12.04 in this 100Gb partition. I used the Ubuntu alternate cd, because the 'normal' cd was giving me trouble with the Raid0. The grub installation always reported a error. After a lot of work I found that I nedded to install grub on partition /dev/mapper/isw_chjbfeec_DougRaid1 (see Bootinfo below). The Windows installation created a 100Mb boot partition, so I needed to install grub in this partition. Now I have the Ubuntu working 100% ok. The problem is, the Windows is not booting! The windows option is present on the grub menu, but when I choose the windows option there is a black screen and after that the grub is reloaded. My Bootinfo is: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for /boot/grub. => Grub2 (v1.99) is installed in the MBR of /dev/mapper/isw_chjbfeec_DougRaid and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for /boot/grub. sda1: __________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' sda2: __________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' mount: unknown filesystem type '' sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: isw_chjbfeec_DougRaid1: ________________________________________________________ File system: ntfs Boot sector type: Grub2 (v1.99) Boot sector info: Grub2 (v1.99) is installed in the boot sector of isw_chjbfeec_DougRaid1 and looks at sector 3841862992 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. No errors found in the Boot Parameter Block. Operating System: Boot files: /grldr /bootmgr /Boot/BCD /grldr isw_chjbfeec_DougRaid2: ________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe isw_chjbfeec_DougRaid3: ________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: isw_chjbfeec_DougRaid5: ________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img isw_chjbfeec_DougRaid6: ________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 206,848 3,686,402,047 3,686,195,200 7 NTFS / exFAT / HPFS /dev/sda3 3,686,402,558 3,907,039,743 220,637,186 5 Extended Invalid MBR Signature found. EBR refers to a location outside the hard drive. /dev/sda2 ends after the last sector of /dev/sda /dev/sda3 ends after the last sector of /dev/sda Drive: isw_chjbfeec_DougRaid _____________________________________________________________________ Disk /dev/mapper/isw_chjbfeec_DougRaid: 2000.4 GB, 2000404348928 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907039744 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/mapper/isw_chjbfeec_DougRaid1 * 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/mapper/isw_chjbfeec_DougRaid2 206,848 3,686,402,047 3,686,195,200 7 NTFS / exFAT / HPFS /dev/mapper/isw_chjbfeec_DougRaid3 3,686,402,558 3,907,039,743 220,637,186 5 Extended /dev/mapper/isw_chjbfeec_DougRaid5 3,686,402,560 3,881,876,479 195,473,920 83 Linux /dev/mapper/isw_chjbfeec_DougRaid6 3,881,876,992 3,907,039,743 25,162,752 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/mapper/isw_chjbfeec_DougRaid1 C89C73D19C73B910 ntfs Reservado pelo Sistema /dev/mapper/isw_chjbfeec_DougRaid2 6830883A3088116C ntfs /dev/mapper/isw_chjbfeec_DougRaid5 bbab868a-ea53-4be3-ba7d-2737fe6cb24c ext4 /dev/mapper/isw_chjbfeec_DougRaid6 7a830a3c-88fb-4cba-80dc-f32e08abfd5b swap /dev/sda isw_raid_member /dev/sdb isw_raid_member /dev/sr0 iso9660 Windows7x86x64SK ========================= "ls -R /dev/mapper/" output: ========================= /dev/mapper: control isw_chjbfeec_DougRaid isw_chjbfeec_DougRaid1 isw_chjbfeec_DougRaid2 isw_chjbfeec_DougRaid3 isw_chjbfeec_DougRaid5 isw_chjbfeec_DougRaid6 ================================ Mount points: ================================= Device Mount_Point Type Options /dev/mapper/isw_chjbfeec_DougRaid5 / ext4 (rw,errors=remount-ro) /dev/sr0 /media/Windows7x86x64SK iso9660 (ro,nosuid,nodev,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500,uhelper=udisks) ================= isw_chjbfeec_DougRaid1/grldr embedded menu: ================== -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- ================== isw_chjbfeec_DougRaid5/boot/grub/grub.cfg: ================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="$1" if [ "$1" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-24-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux /boot/vmlinuz-3.2.0-24-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-24-generic-pae } menuentry 'Ubuntu, with Linux 3.2.0-24-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c echo 'Loading Linux 3.2.0-24-generic-pae ...' linux /boot/vmlinuz-3.2.0-24-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-24-generic-pae } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 3.2.0-23-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux /boot/vmlinuz-3.2.0-23-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-23-generic-pae } menuentry 'Ubuntu, with Linux 3.2.0-23-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c echo 'Loading Linux 3.2.0-23-generic-pae ...' linux /boot/vmlinuz-3.2.0-23-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-23-generic-pae } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober_proxy ### menuentry "Windows 7 (loader) (on /dev/mapper/isw_chjbfeec_DougRaid1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(sda,msdos1)' search --no-floppy --fs-uuid --set=root C89C73D19C73B910 chainloader +1 } ### END /etc/grub.d/30_os-prober_proxy ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- ====================== isw_chjbfeec_DougRaid5/etc/fstab: ======================= -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/isw_chjbfeec_DougRaid5 / ext4 errors=remount-ro 0 1 /dev/mapper/isw_chjbfeec_DougRaid6 none swap sw 0 0 -------------------------------------------------------------------------------- ========== isw_chjbfeec_DougRaid5: Location of files loaded by Grub: =========== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-23-generic-pae 2 = boot/initrd.img-3.2.0-24-generic-pae 2 = boot/vmlinuz-3.2.0-23-generic-pae 1 = boot/vmlinuz-3.2.0-24-generic-pae 1 = initrd.img 2 = initrd.img.old 2 = vmlinuz 1 = vmlinuz.old 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda1 Unknown BootLoader on sda2 Unknown BootLoader on sda3 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt hexdump: /dev/sda1: No such file or directory hexdump: /dev/sda1: No such file or directory hexdump: /dev/sda2: No such file or directory hexdump: /dev/sda2: No such file or directory hexdump: /dev/sda3: No such file or directory hexdump: /dev/sda3: No such file or directory xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in How we can see the Windows part at grub is: menuentry "Windows 7 (loader) (on /dev/mapper/isw_chjbfeec_DougRaid1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(sda,msdos1)' search --no-floppy --fs-uuid --set=root C89C73D19C73B910 chainloader +1 } I tried a lot of combinations at the line: set root='(sda,msdos1)' , but no success I tried to change uuid to the /dev/mapper/isw_chjbfeec_DougRaid2 uuid, but the grub reports a error. I dont know what to do now. I really need to boot my windows partition. Someone knows what to do? Thanks........

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• CodePlex Daily Summary for Tuesday, October 22, 2013

  CodePlex Daily Summary for Tuesday, October 22, 2013Popular ReleasesLINQ to Twitter: LINQ to Twitter v2.1.10: Supports .NET 3.5, .NET 4.0, .NET 4.5, Silverlight 4.0, Windows Phone 7.1, Windows Phone 8, Client Profile, Windows 8, and Windows Azure. 100% Twitter API coverage. Also supports Twitter API v1.1! Also on NuGet.Grauers Hide Ribbon Items: Grauers Hide Ribbon Items: Hiding ribbon items in a SharePoint libraryMedia Companion: Media Companion MC3.584b: IMDB changes fixed. Fixed* mc_com.exe - Fixed to using new profile entries. * Movie - fixed rename movie and folder if use foldername selected. * Movie - Alt Edit Movie, trailer url check if changed and confirm valid. * Movie - Fixed IMDB poster scraping * Movie - Fixed outline and Plot scraping, including removal of Hyperlink's. * Movie Poster refactoring, attempts to catch gdi+ errors Revision HistoryJayData -The unified data access library for JavaScript: JayData 1.3.4: JayData is a unified data access library for JavaScript to CRUD + Query data from different sources like WebAPI, OData, MongoDB, WebSQL, SQLite, HTML5 localStorage, Facebook or YQL. The library can be integrated with KendoUI, Angular.js, Knockout.js or Sencha Touch 2 and can be used on Node.js as well. See it in action in this 6 minutes video KendoUI examples: JayData example site Examples for map integration JayData example site What's new in JayData 1.3.4 For detailed release notes check ...TerrariViewer: TerrariViewer v7.2 [Terraria Inventory Editor]: Added "Check for Update" button Hopefully fixed Windows XP issue You can now backspace in Item stack fieldsIsWiX: IsWiX 2.2.13293.1: This a minor enhancement of the 2.1 release. IsWiX Merge Module projects now include a second wxs fragment file that is useful for inserting `custom` components not supposed by the IsWiX UI.Simple Injector: Simple Injector v2.3.6: This patch releases fixes one bug concerning resolving open generic types that contain nested generic type arguments. Nested generic types were handled incorrectly in certain cases. This affects RegisterOpenGeneric and RegisterDecorator. (work item 20332)Virtual Wifi Hotspot for Windows 7 & 8: Virtual Router Plus 2.6.0: Virtual Router Plus 2.6.0Fast YouTube Downloader: Fast YouTube Downloader 2.3.0: Fast YouTube DownloaderMagick.NET: Magick.NET 6.8.7.101: Magick.NET linked with ImageMagick 6.8.7.1. Breaking changes: - Renamed Matrix classes: MatrixColor = ColorMatrix and MatrixConvolve = ConvolveMatrix. - Renamed Depth method with Channels parameter to BitDepth and changed the other method into a property.VidCoder: 1.5.9 Beta: Added Rip DVD and Rip Blu-ray AutoPlay actions for Windows: now you can have VidCoder start up and scan a disc when you insert it. Go to Start -> AutoPlay to set it up. Added error message for Windows XP users rather than letting it crash. Removed "quality" preset from list for QSV as it currently doesn't offer much improvement. Changed installer to ignore version number when copying files over. Should reduce the chances of a bug from me forgetting to increment a version number. Fixed ...MSBuild Extension Pack: October 2013: Release Blog Post The MSBuild Extension Pack October 2013 release provides a collection of over 480 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...VG-Ripper & PG-Ripper: VG-Ripper 2.9.49: changes NEW: Added Support for "ImageTeam.org links NEW: Added Support for "ImgNext.com" links NEW: Added Support for "HostUrImage.com" links NEW: Added Support for "3XVintage.com" linksMoreTerra (Terraria World Viewer): MoreTerra 1.11.3.1: Release 1.11.3.1 ================ = New Features = ================ Added markers for Copper Cache, Silver Cache and the Enchanted Sword. ============= = Bug Fixes = ============= Use Official Colors now no longer tries to change the Draw Wires option instead. World reading was breaking for people with a stock 1.2 Terraria version. Changed world name reading so it does not crash the program if you load MoreTerra while Terraria is saving the world. =================== = Feature Removal = =...patterns & practices - Windows Azure Guidance: Cloud Design Patterns: 1st drop of Cloud Design Patterns project. It contains 14 patterns with 6 related guidance.Player Framework by Microsoft: Player Framework for Windows and WP (v1.3): Includes all changes in v1.3 beta 1 and v1.3 beta 2 Support for Windows 8.1 RTM and VS2013 RTM Xaml: New property: AutoLoadPluginTypes to help control which stock plugins are loaded by default (requires AutoLoadPlugins = true). Support for SystemMediaTransportControls on Windows 8.1 JS: Support for visual markers in the timeline. JS: Support for markers collection and markerreached event. JS: New ChaptersPlugin to automatically populate timeline with chapter tracks. JS: Audio an...Json.NET: Json.NET 5.0 Release 8: Fix - Fixed not writing string quotes when QuoteName is falsePowerShell Community Extensions: 3.1 Production: PowerShell Community Extensions 3.1 Release NotesOct 17, 2013 This version of PSCX supports Windows PowerShell 3.0 and 4.0 See the ReleaseNotes.txt download above for more information.Social Network Importer for NodeXL: SocialNetImporter(v.1.9): This new version includes: - Download latest status update and use it as vertex tooltip - Limit the timelines to parse to me, my friends or both - Fixed some reported bugs about the fan page and group importer - Fixed the login bug reported latelyPython Tools for Visual Studio: 2.0: PTVS 2.0 We’re pleased to announce the release of Python Tools for Visual Studio 2.0 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, IPython, and cross platform and cross language debugging support. QUICK VIDEO OVERVIEW For a quick overview of the general IDE experience, please watch this v...New Projects40FINGERS NB_Store Menumanipulator: This component allows you to add the categories of your NB_Store webshop to your DotNetNuke website's menu.ABCat: ??????? ?????????? ???????????? ????????, ?????????????? ??????? ??? ????????? ????????? ?????????? ? ?????????? ????? ?????????.AUTOFIX: This is a project related to Web Application development for University of HertfordshireAutomated service accounts creation for SharePoint 2010 and 2013 and SQL Server: Purpose of this project is just to automate the creation of SharePoint Service accounts in Active Directory.BeatportPro: Windows version of Beatport ProCasaNet: CasaNetFree Cascaded Dropdown lists JQuery Plugin for SharePoint Forms: SPCascade lets you create multi-level cascaded dropdown lists on a SharePoint form using easy JQuery code.GODspeed - FTP client for JTAG/RGH Xbox 360 consoles: Total Commander like FTP client designed to fasten and clarify file management of JTAG/RGH/DevKit Xbox 360 consoles.HCI Web Search: This project seaches for using alternative ways to handle and to visualize Web search results in a 3D environment, by interacting with gestures and speech reco.HengbeiVillage: ASP.Net + EF + AjaxToolkit ControlsIntegração Cielo Nopcommerce: Realizar a integração nopcommerce com a Cielo. Maiores detalhes são bem vindo.juzgadosdelaciudad: Mapa con Juzgados de la ciudad de buenos airesLeapJanken: LeapMotion?????、Windows Store Apps??????????????????。Looking tester for Template Engine: -VALIDATE TEMPLATE SYNTAX - no template parsing overhead, only compiles once. - unlimited nesting of sections, conditionals, etc.MQTT Broker for .NET: Project to develop a broker (server) for the MQTT protocol, an M2M Internet-of-Things communication protocol.NC MKT DNT: NC MKTNet Imobiliaria: Projeto Integrador IV SenacNewBiz: NewBiz Java Web ApplicationOAuthServer: OAuthServer is an Open Authentication server that allows you to securely authenticate your Active Directory users directly on the internet.QlikBar SDK for .NET 2.0: QlikBar SDK for .NET 2.0RainNoise - The Sound of Rain, without the wet feet.: Making some rain noise for Android device.Redsys / Sermepa gateway for Asp.Net MVC4: Coming soon....Restore Exchange 2003 Data to Exchange 2010: SysTools Exchange Recovery tool which proffers efficient and beneficial features in order to restore or migrate Exchange mailboxes from one server to anotherTimely: A library to fluently work with DateTime and TimeSpan objectstutorials_online: This is a project that is associated with my progress in tutorials in Web Scripting and Application Development in for the University of HertfordshireUQBuy ?????: ??????，?????，????，??????Voxel To Mesh Converter: Converts voxel models into mesh models.

  Read the article

• Recover RAID 5 data after created new array instead of re-using

  - by Brigadieren

  Folks please help - I am a newb with a major headache at hand (perfect storm situation). I have a 3 1tb hdd on my ubuntu 11.04 configured as software raid 5. The data had been copied weekly onto another separate off the computer hard drive until that completely failed and was thrown away. A few days back we had a power outage and after rebooting my box wouldn't mount the raid. In my infinite wisdom I entered mdadm --create -f... command instead of mdadm --assemble and didn't notice the travesty that I had done until after. It started the array degraded and proceeded with building and syncing it which took ~10 hours. After I was back I saw that that the array is successfully up and running but the raid is not I mean the individual drives are partitioned (partition type f8 ) but the md0 device is not. Realizing in horror what I have done I am trying to find some solutions. I just pray that --create didn't overwrite entire content of the hard driver. Could someone PLEASE help me out with this - the data that's on the drive is very important and unique ~10 years of photos, docs, etc. Is it possible that by specifying the participating hard drives in wrong order can make mdadm overwrite them? when I do mdadm --examine --scan I get something like ARRAY /dev/md/0 metadata=1.2 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b name=<hostname>:0 Interestingly enough name used to be 'raid' and not the host hame with :0 appended. Here is the 'sanitized' config entries: DEVICE /dev/sdf1 /dev/sde1 /dev/sdd1 CREATE owner=root group=disk mode=0660 auto=yes HOMEHOST <system> MAILADDR root ARRAY /dev/md0 metadata=1.2 name=tanserv:0 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b Here is the output from mdstat cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[0] sdf1[3] sde1[1] 1953517568 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/3] [UUU] unused devices: <none> fdisk shows the following: fdisk -l Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bf62e Device Boot Start End Blocks Id System /dev/sda1 * 1 9443 75846656 83 Linux /dev/sda2 9443 9730 2301953 5 Extended /dev/sda5 9443 9730 2301952 82 Linux swap / Solaris Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de8dd Device Boot Start End Blocks Id System /dev/sdb1 1 91201 732572001 8e Linux LVM Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00056a17 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 8e Linux LVM Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ca948 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/dm-0: 1250.3 GB, 1250254913536 bytes 255 heads, 63 sectors/track, 152001 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93a66687 Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6edc059 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/md0: 2000.4 GB, 2000401989632 bytes 2 heads, 4 sectors/track, 488379392 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1048576 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Per suggestions I did clean up the superblocks and re-created the array with --assume-clean option but with no luck at all. Is there any tool that will help me to revive at least some of the data? Can someone tell me what and how the mdadm --create does when syncs to destroy the data so I can write a tool to un-do whatever was done? After the re-creating of the raid I run fsck.ext4 /dev/md0 and here is the output root@tanserv:/etc/mdadm# fsck.ext4 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Superblock invalid, trying backup blocks... fsck.ext4: Bad magic number in super-block while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 Per Shanes' suggestion I tried root@tanserv:/home/mushegh# mkfs.ext4 -n /dev/md0 mke2fs 1.41.14 (22-Dec-2010) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=128 blocks, Stripe width=256 blocks 122101760 inodes, 488379392 blocks 24418969 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 14905 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 and run fsck.ext4 with every backup block but all returned the following: root@tanserv:/home/mushegh# fsck.ext4 -b 214990848 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Invalid argument while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> Any suggestions? Regards!

  Read the article

• Why can't I connect to a Cisco wireless access point?

  - by spinlock

  I'm running a Lucid Netbook Remix on my Dell Inspiron 600m and I was not able to connect to the wireless network at the Hacker Dojo in Mountain View yesterday. There were plenty of other people on the network - MS, Mac, and Linux boxes - but my laptop would never get an ip address. I can connect to my home network, which is open, and I've never had a problem connecting at the coffee shop, which uses WPA. The Hacker Dojo is running WPA and we checked the password a number of times but got no love. Any ideas would be greatly appreciated. Additional Info: $iwlist eth1 scan eth1 Scan completed : Cell 01 - Address: EC:C8:82:FA:63:92 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:62 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 280ms ago Cell 02 - Address: 00:18:4D:24:08:61 ESSID:"Green Zone" Protocol:IEEE 802.11bg Mode:Master Frequency:2.417 GHz (Channel 2) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:23 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 11516ms ago Cell 03 - Address: 08:17:35:32:6E:13 ESSID:"\x00" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:71 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 2760ms ago Cell 04 - Address: EC:C8:82:FA:63:90 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:61 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 772ms ago Cell 05 - Address: 08:17:35:32:6E:11 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:65 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 3308ms ago Cell 06 - Address: 08:17:35:32:7E:31 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:88 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 1668ms ago Cell 07 - Address: 38:E7:D8:01:46:1E ESSID:"JWS_Incredible" Protocol:IEEE 802.11bg Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 500 kb/s; 54 Mb/s Quality:31 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Extra: Last beacon: 2848ms ago Cell 08 - Address: 08:17:35:32:6E:10 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:67 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 7848ms ago Cell 09 - Address: 08:17:35:32:7E:30 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:85 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 8300ms ago Cell 10 - Address: 08:17:35:32:6E:12 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:68 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 232ms ago Cell 11 - Address: 08:17:35:32:7E:32 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:86 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 168ms ago Cell 12 - Address: EC:C8:82:FA:63:91 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:62 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 7408ms ago $iwconfig eth1 eth1 unassociated ESSID:"HackerDojo-gwifi" Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:16 dBm Retry short limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• How do I get a rt2800usb wireless device working?

  - by Jii

  My brand new desktop running 13.04 has endless problems with wireless. Dozens of others are flooding forums with reports of the same problems. It worked fine for a few days, then there were a few days where it started having problems sometimes and working sometimes. Now it never works at all. I have 5+ devices all able to connect without any trouble at all, including iPhone, Android phone, 3DS, multiple game consoles, a laptop running windows 7, and even a second desktop machine running Ubuntu 12.04 sitting right behind the 13.04 machine. All other devices have full wireless bars displayed (strong signals). At any moment, one of the following is happening, and it changes randomly: Trying to connect forever, but never establishing a connection. Wireless icon constantly animating. Finds no wireless networks at all. (There are 12+ in range according to other devices.) Will not try to connect to the network. If I use the icon to connect, it will display "Disconnected" within a few seconds. Will continuously ask for the network password. Typing it in correctly does not help. Wireless is working fine. This happens sometimes. It can work for days at a time, or only 10 mins at a time. Various things that usually do nothing but sometimes fix the problem: Reboot. This has the best chance of helping, but it usually takes 5+ times. Disable/re-enable Wi-Fi using the wireless icon. Disable/re-enable Networking using the wireless icon. Use the icon to try and connect to a network (if found). Use the icon to open Edit Connections and delete my connection info, causing it to be recreated (once it's actually found again). Various things that seem to make no difference: Changing between using Linux headers in grub at bootup, between 3.10.0, 3.9.0, or 3.8.0. Move the wireless router very close to the desktop. Running sudo rfkill unblock all (I dunno what this is supposed to do.) I've used Ubuntu for 6 years and I've never had a problem with networking. Now I'm spending all my time reading through endless problem reports and trying all the answers. None of them have helped. I am doing this instead of getting work done, which is defeating the whole purpose of using Ubuntu. It's heartbreaking to be honest. In the current state of "no networks are showing up", here are outputs from the random things that other people are usually asked to run: lspic 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) lsmod Module Size Used by e100 41119 0 nls_iso8859_1 12713 1 parport_pc 28284 0 ppdev 17106 0 bnep 18258 2 rfcomm 47863 12 binfmt_misc 17540 1 arc4 12573 2 rt2800usb 27201 0 rt2x00usb 20857 1 rt2800usb rt2800lib 68029 1 rt2800usb rt2x00lib 55764 3 rt2x00usb,rt2800lib,rt2800usb coretemp 13596 0 mac80211 656164 3 rt2x00lib,rt2x00usb,rt2800lib kvm_intel 138733 0 kvm 452835 1 kvm_intel cfg80211 547224 2 mac80211,rt2x00lib crc_ccitt 12707 1 rt2800lib ghash_clmulni_intel 13259 0 aesni_intel 55449 0 usb_storage 61749 1 aes_x86_64 17131 1 aesni_intel joydev 17613 0 xts 12922 1 aesni_intel nouveau 1001310 3 snd_hda_codec_hdmi 37407 1 lrw 13294 1 aesni_intel gf128mul 14951 2 lrw,xts mxm_wmi 13021 1 nouveau snd_hda_codec_realtek 46511 1 ablk_helper 13597 1 aesni_intel wmi 19256 2 mxm_wmi,nouveau snd_hda_intel 44397 5 ttm 88251 1 nouveau drm_kms_helper 49082 1 nouveau drm 295908 5 ttm,drm_kms_helper,nouveau snd_hda_codec 190010 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel cryptd 20501 3 ghash_clmulni_intel,aesni_intel,ablk_helper snd_hwdep 13613 1 snd_hda_codec snd_pcm 102477 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel btusb 18291 0 snd_page_alloc 18798 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 i2c_algo_bit 13564 1 nouveau snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30417 1 snd_seq_midi snd_seq 61930 2 snd_seq_midi_event,snd_seq_midi bluetooth 251354 22 bnep,btusb,rfcomm snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi lpc_ich 17060 0 snd_timer 29989 2 snd_pcm,snd_seq mei 46588 0 snd 69533 20 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device psmouse 97838 0 microcode 22923 0 soundcore 12680 1 snd video 19467 1 nouveau mac_hid 13253 0 serio_raw 13215 0 lp 17799 0 parport 46562 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 47346 0 hid 101248 2 hid_generic,usbhid ahci 30063 3 libahci 32088 1 ahci e1000e 207005 0 ptp 18668 1 e1000e pps_core 14080 1 ptp sudo lshw -c network 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) sudo iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on sudo iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results NOTE: This dmesg was done after a reboot where the network manager was continuously displaying the "disconnected" message over and over. So it must have been trying to connect at this time. My network was displayed in the list of options, as the only option despite other devices picking up 12+ access points. The router channel is set to auto. dmesg | tail -30 [ 187.418446] wlan0: associated [ 190.405601] wlan0: disassociated from 00:14:d1:a8:c3:44 (Reason: 15) [ 190.443312] cfg80211: Calling CRDA to update world regulatory domain [ 190.443431] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 190.451635] cfg80211: World regulatory domain updated: [ 190.451643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 190.451648] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451652] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451656] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451659] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451662] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 191.824451] wlan0: authenticate with 00:14:d1:a8:c3:44 [ 191.850608] wlan0: send auth to 00:14:d1:a8:c3:44 (try 1/3) [ 191.884604] wlan0: send auth to 00:14:d1:a8:c3:44 (try 2/3) [ 191.886309] wlan0: authenticated [ 191.886579] rt2800usb 3-5.3:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 191.886588] rt2800usb 3-5.3:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 191.889556] wlan0: associate with 00:14:d1:a8:c3:44 (try 1/3) [ 192.001493] wlan0: associate with 00:14:d1:a8:c3:44 (try 2/3) [ 192.040274] wlan0: RX AssocResp from 00:14:d1:a8:c3:44 (capab=0x431 status=0 aid=3) [ 192.044235] wlan0: associated [ 193.948188] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 193.981501] cfg80211: Calling CRDA to update world regulatory domain [ 193.984080] cfg80211: World regulatory domain updated: [ 193.984082] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 193.984084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984086] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984087] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) The router uses MAC filtering, and security is WPA PSK with cipher as auto. So, any ideas? Or is the solution just to not use 13.04 unless you have a wired connection? (I don't have this option.) If so, please just tell me straight. I survived 9.04 Jaunty, and I can survive 13.04 Raring. Update #1 Results from trying Wild Man's first answer: jii@conan:~$ echo "options rt2800usb nohwcrypt=y" | sudo tee /etc/modprobe.d/rt2800usb.conf options rt2800usb nohwcrypt=y jii@conan:~$ sudo modprobe -rfv rt2800usb rmmod rt2800usb rmmod rt2800lib rmmod crc_ccitt rmmod rt2x00usb rmmod rt2x00lib rmmod mac80211 rmmod cfg80211 jii@conan:~$ sudo modprobe -v rt2800usb insmod /lib/modules/3.10.0-031000-generic/kernel/lib/crc-ccitt.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko nohwcrypt=y I tried: gksudo gedit /etc/pm/power.d/wireless but I didn't have the package. It said to install gksu. I tried that, but of course, not having Internet, I didn't get the package. So instead I did: sudo gedit /etc/pm/power.d/wireless Which created the file. Here is the body: #!/bin/sh /sbin/iwconfig wlan0 power off I then rebooted. No change. I tried adding exit 0 to the bottom of the wireless file, and rebooted. No change. Please note that this is a desktop machine. I'm assuming power management is primarily for laptops, but the iwconfig does state that power management is on, so who knows. The recommended router changes I did not do, since the current router settings are (I think) required for some of the older devices I have, and because the current settings work on all my modern devices including Ubuntu 12.04 and Windows 7. I do appreciate the advice though, and I'll look into it when I have time. Anything else to try? Update #2 I booted into Ubuntu 12.04.3 from a dvd, and the same problems exist. I have a separate old desktop machine with 12.04 installed that has no wireless problems at all. So obviously the problem is wireless hardware compatibility in both 12.04.03 LTS and 13.04. Update #3 The same problems exist even when using a wired connection. I plugged an ethernet cable directly to the router and the network manager added an "Auto Ethernet" entry, but it cannot establish a connection to it. So the problem is not specific to wireless. Meanwhile, I purchased a Trendnet N300 wireless USB adapter, TEW-664UB. I plugged it in, but I have no idea how to get Ubuntu to try and use it. Can anyone tell me how? Can I download a package on another computer and copy the .deb over to do an install, etc? I'm installing windows 7 to double check that the internet connection works there and it's not just some magically faulty hardware. Thanks for your help.

  Read the article

• OpenVPN - client-to-client traffic working in one direction but not the other

  - by Pawz

  I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. I am using "fragment 1400" and "mssfix" on all three machines. An mtu-test on both connections is successful. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ? FWIW, pinging 10.0.1.253 from Kino has the same result - the traffic does not get forwarded. UPDATE: I've found that I can only ping certain IP's on Guchuko's LAN from Outpost. From Outpost I can ping 192.168.0.3 and 192.168.0.2, but 192.168.99 and 192.168.0.4 are unreachable. The same tcpdump behavior can be seen. I think this means the problem can't be due to ipforwarding or routing, because Outpost can reach SOME hosts on Guchuko's LAN but not others and likewise, Guchuko can reach two hosts on Outpost's LAN, but not others. This baffles me.

  Read the article

• Using xsl:variable in a xsl:foreach select statment

  - by Nefariousity

  I'm trying to iterate through an xml document using xsl:foreach but I need the select=" " to be dynamic so I'm using a variable as the source. Here's what I've tried: ... <xsl:template name="SetDataPath"> <xsl:param name="Type" /> <xsl:variable name="Path_1">/Rating/Path1/*</xsl:variable> <xsl:variable name="Path_2">/Rating/Path2/*</xsl:variable> <xsl:if test="$Type='1'"> <xsl:value-of select="$Path_1"/> </xsl:if> <xsl:if test="$Type='2'"> <xsl:value-of select="$Path_2"/> </xsl:if> <xsl:template> ... <!-- Set Data Path according to Type --> <xsl:variable name="DataPath"> <xsl:call-template name="SetDataPath"> <xsl:with-param name="Type" select="/Rating/Type" /> </xsl:call-template> </xsl:variable> ... <xsl:for-each select="$DataPath"> ... The foreach threw an error stating: "XslTransformException - To use a result tree fragment in a path expression, first convert it to a node-set using the msxsl:node-set() function." When I use the msxsl:node-set() function though, my results are blank. I'm aware that I'm setting $DataPath to a string, but shouldn't the node-set() function be creating a node set from it? Am I missing something? When I don't use a variable: <xsl:for-each select="/Rating/Path1/*"> I get the proper results. Here's the XML data file I'm using: <Rating> <Type>1</Type> <Path1> <sarah> <dob>1-3-86</dob> <user>Sarah</user> </sarah> <joe> <dob>11-12-85</dob> <user>Joe</user> </joe> </Path1> <Path2> <jeff> <dob>11-3-84</dob> <user>Jeff</user> </jeff> <shawn> <dob>3-5-81</dob> <user>Shawn</user> </shawn> </Path2> </Rating> My question is simple, how do you run a foreach on 2 different paths?

  Read the article

• I am trying to deploy my first rails app using Capistrano and am getting an error.

  - by Andrew Bucknell

  My deployment of a rails app with capistrano is failing and I hoping someone can provide me with pointers to troubleshoot. The following is the command output andrew@melb-web:~/projects/rails/guestbook2$ cap deploy:setup * executing `deploy:setup' * executing "mkdir -p /var/www/dev/guestbook2 /var/www/dev/guestbook2/releases /var/www/dev/guestbook2/shared /var/www/dev/guestbook2/shared/system /var/www/dev/guestbook2/shared/log /var/www/dev/guestbook2/shared/pids && chmod g+w /var/www/dev/guestbook2 /var/www/dev/guestbook2/releases /var/www/dev/guestbook2/shared /var/www/dev/guestbook2/shared/system /var/www/dev/guestbook2/shared/log /var/www/dev/guestbook2/shared/pids" servers: ["dev.andrewbucknell.com"] Enter passphrase for /home/andrew/.ssh/id_dsa: Enter passphrase for /home/andrew/.ssh/id_dsa: [dev.andrewbucknell.com] executing command command finished andrew@melb-web:~/projects/rails/guestbook2$ cap deploy:check * executing `deploy:check' * executing "test -d /var/www/dev/guestbook2/releases" servers: ["dev.andrewbucknell.com"] Enter passphrase for /home/andrew/.ssh/id_dsa: [dev.andrewbucknell.com] executing command command finished * executing "test -w /var/www/dev/guestbook2" servers: ["dev.andrewbucknell.com"] [dev.andrewbucknell.com] executing command command finished * executing "test -w /var/www/dev/guestbook2/releases" servers: ["dev.andrewbucknell.com"] [dev.andrewbucknell.com] executing command command finished * executing "which git" servers: ["dev.andrewbucknell.com"] [dev.andrewbucknell.com] executing command command finished * executing "test -w /var/www/dev/guestbook2/shared" servers: ["dev.andrewbucknell.com"] [dev.andrewbucknell.com] executing command command finished You appear to have all necessary dependencies installed andrew@melb-web:~/projects/rails/guestbook2$ cap deploy:migrations * executing `deploy:migrations' * executing `deploy:update_code' updating the cached checkout on all servers executing locally: "git ls-remote [email protected]:/home/andrew/git/guestbook2.git master" Enter passphrase for key '/home/andrew/.ssh/id_dsa': * executing "if [ -d /var/www/dev/guestbook2/shared/cached-copy ]; then cd /var/www/dev/guestbook2/shared/cached-copy && git fetch origin && git reset --hard 369c5e04aaf83ad77efbfba0141001ac90915029 && git clean -d -x -f; else git clone [email protected]:/home/andrew/git/guestbook2.git /var/www/dev/guestbook2/shared/cached-copy && cd /var/www/dev/guestbook2/shared/cached-copy && git checkout -b deploy 369c5e04aaf83ad77efbfba0141001ac90915029; fi" servers: ["dev.andrewbucknell.com"] Enter passphrase for /home/andrew/.ssh/id_dsa: [dev.andrewbucknell.com] executing command ** [dev.andrewbucknell.com :: err] Permission denied, please try again. ** Permission denied, please try again. ** Permission denied (publickey,password). ** [dev.andrewbucknell.com :: err] fatal: The remote end hung up unexpectedly ** [dev.andrewbucknell.com :: out] Initialized empty Git repository in /var/www/dev/guestbook2/shared/cached-copy/.git/ command finished failed: "sh -c 'if [ -d /var/www/dev/guestbook2/shared/cached-copy ]; then cd /var/www/dev/guestbook2/shared/cached-copy && git fetch origin && git reset --hard 369c5e04aaf83ad77efbfba0141001ac90915029 && git clean -d -x -f; else git clone [email protected]:/home/andrew/git/guestbook2.git /var/www/dev/guestbook2/shared/cached-copy && cd /var/www/dev/guestbook2/shared/cached-copy && git checkout -b deploy 369c5e04aaf83ad77efbfba0141001ac90915029; fi'" on dev.andrewbucknell.com andrew@melb-web:~/projects/rails/guestbook2$ The following fragment is from cap -d deploy:migrations Preparing to execute command: "find /var/www/dev/guestbook2/releases/20100305124415/public/images /var/www/dev/guestbook2/releases/20100305124415/public/stylesheets /var/www/dev/guestbook2/releases/20100305124415/public/javascripts -exec touch -t 201003051244.22 {} ';'; true" Execute ([Yes], No, Abort) ? |y| yes * executing `deploy:migrate' * executing "ls -x /var/www/dev/guestbook2/releases" Preparing to execute command: "ls -x /var/www/dev/guestbook2/releases" Execute ([Yes], No, Abort) ? |y| yes /usr/lib/ruby/gems/1.8/gems/capistrano-2.5.17/lib/capistrano/recipes/deploy.rb:55:in `join': can't convert nil into String (TypeError) from /usr/lib/ruby/gems/1.8/gems/capistrano-2.5.17/lib/capistrano/recipes/deploy.rb:55:in `load'

  Read the article

• Custom listview entry works in JB not in Gingerbread

  - by Andy

  I have a ListFragment with a custom ArrayAdapter where I am overiding getView() to provide a custom View for the list item. private class DirListAdaptor extends ArrayAdapter<DirItem> { @Override public View getView(int position, View convertView, ViewGroup parent) { View aView = convertView; if (aView == null) { LayoutInflater vi = (LayoutInflater) getContext().getSystemService(Context.LAYOUT_INFLATER_SERVICE); // TODO: can we not access textViewResourceId? aView = vi.inflate(R.layout.dir_list_entry, parent, false); } etc... Here is the dir_list_entry.xml: <RelativeLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="match_parent" android:layout_height="?android:attr/listPreferredItemHeight" android:paddingLeft="?android:attr/listPreferredItemPaddingLeft" android:paddingRight="?android:attr/listPreferredItemPaddingRight"> <ImageView android:id="@+id/dir_list_icon" android:layout_width="wrap_content" android:layout_height="match_parent" android:layout_alignParentTop="true" android:layout_alignParentBottom="true" android:layout_marginRight="6dp" android:src="@drawable/ic_launcher" /> <TextView android:id="@+id/dir_list_details" android:textAppearance="?android:attr/textAppearanceListItem" android:layout_width="match_parent" android:layout_height="wrap_content" android:layout_toRightOf="@id/dir_list_icon" android:layout_alignParentBottom="true" android:layout_alignParentRight="true" android:singleLine="true" android:ellipsize="marquee" android:textSize="12sp" android:text="Details" /> <TextView android:id="@+id/dir_list_filename" android:textAppearance="?android:attr/textAppearanceListItem" android:layout_width="match_parent" android:layout_height="wrap_content" android:layout_toRightOf="@id/dir_list_icon" android:layout_alignParentRight="true" android:layout_alignParentTop="true" android:layout_above="@id/dir_list_details" android:layout_alignWithParentIfMissing="true" android:gravity="center_vertical" android:textSize="14sp" android:text="Filename"/> </RelativeLayout> The bizarre thing is this works fine on Android 4.1 emulator, but I get the following error on Android 2.3: 10-01 15:07:59.594: ERROR/AndroidRuntime(1003): FATAL EXCEPTION: main android.view.InflateException: Binary XML file line #1: Error inflating class android.widget.RelativeLayout at android.view.LayoutInflater.createView(LayoutInflater.java:518) at com.android.internal.policy.impl.PhoneLayoutInflater.onCreateView(PhoneLayoutInflater.java:56) at android.view.LayoutInflater.createViewFromTag(LayoutInflater.java:568) at android.view.LayoutInflater.inflate(LayoutInflater.java:386) at android.view.LayoutInflater.inflate(LayoutInflater.java:320) at com.eveps.evepsdroid.ui.PhotoBrowserListFragment$DirListAdaptor.getView(PhotoBrowserListFragment.java:104) at android.widget.AbsListView.obtainView(AbsListView.java:1430) at android.widget.ListView.makeAndAddView(ListView.java:1745) at android.widget.ListView.fillDown(ListView.java:670) at android.widget.ListView.fillFromTop(ListView.java:727) at android.widget.ListView.layoutChildren(ListView.java:1598) at android.widget.AbsListView.onLayout(AbsListView.java:1260) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1254) at android.widget.LinearLayout.layoutHorizontal(LinearLayout.java:1243) at android.widget.LinearLayout.onLayout(LinearLayout.java:1049) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1254) at android.widget.LinearLayout.layoutVertical(LinearLayout.java:1130) at android.widget.LinearLayout.onLayout(LinearLayout.java:1047) at android.view.View.layout(View.java:7175) at android.widget.FrameLayout.onLayout(FrameLayout.java:338) at android.view.View.layout(View.java:7175) at android.view.ViewRoot.performTraversals(ViewRoot.java:1140) at android.view.ViewRoot.handleMessage(ViewRoot.java:1859) at android.os.Handler.dispatchMessage(Handler.java:99) at android.os.Looper.loop(Looper.java:123) at android.app.ActivityThread.main(ActivityThread.java:3683) at java.lang.reflect.Method.invokeNative(Native Method) at java.lang.reflect.Method.invoke(Method.java:507) at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:839) at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:597) at dalvik.system.NativeStart.main(Native Method) Caused by: java.lang.reflect.InvocationTargetException at java.lang.reflect.Constructor.constructNative(Native Method) at java.lang.reflect.Constructor.newInstance(Constructor.java:415) at android.view.LayoutInflater.createView(LayoutInflater.java:505) ... 42 more Caused by: java.lang.UnsupportedOperationException: Can't convert to dimension: type=0x2 at android.content.res.TypedArray.getDimensionPixelSize(TypedArray.java:463) at android.view.View.<init>(View.java:1957) at android.view.View.<init>(View.java:1899) at android.view.ViewGroup.<init>(ViewGroup.java:286) at android.widget.RelativeLayout.<init>(RelativeLayout.java:173) ... 45 more I'm using the Android Support library for fragment support obviously. Seems to be a problem inflating the custom list view entry, something to do with a dimension - but why does it work on JellyBean? Has something changed in this area?

  Read the article

• Calling the same xsl:template for different node names of the same complex type

  - by CraftyFella

  Hi, I'm trying to keep my xsl DRY and as a result I wanted to call the same template for 2 sections of an XML document which happen to be the same complex type (ContactDetails and AltContactDetails). Given the following XML: <?xml version="1.0" encoding="UTF-8"?> <RootNode> <Name>Bob</Name> <ContactDetails> <Address> <Line1>1 High Street</Line1> <Town>TownName</Town> <Postcode>AB1 1CD</Postcode> </Address> <Email>[email protected]</Email> </ContactDetails> <AltContactDetails> <Address> <Line1>3 Market Square</Line1> <Town>TownName</Town> <Postcode>EF2 2GH</Postcode> </Address> <Email>[email protected]</Email> </AltContactDetails> </RootNode> I wrote an XSL Stylesheet as follows: <?xml version="1.0" encoding="UTF-8"?> <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" version="1.0"> <xsl:template match="/"> <PersonsName> <xsl:value-of select="RootNode/Name"/> </PersonsName> <xsl:call-template name="ContactDetails"> <xsl:with-param name="data"><xsl:value-of select="RootNode/ContactDetails"/></xsl:with-param> <xsl:with-param name="elementName"><xsl:value-of select="'FirstAddress'"/></xsl:with-param> </xsl:call-template> <xsl:call-template name="ContactDetails"> <xsl:with-param name="data"><xsl:value-of select="RootNode/AltContactDetails"/></xsl:with-param> <xsl:with-param name="elementName"><xsl:value-of select="'SecondAddress'"/></xsl:with-param> </xsl:call-template> </xsl:template> <xsl:template name="ContactDetails"> <xsl:param name="data"></xsl:param> <xsl:param name="elementName"></xsl:param> <xsl:element name="{$elementName}"> <FirstLine> <xsl:value-of select="$data/Address/Line1"/> </FirstLine> <Town> <xsl:value-of select="$data/Address/Town"/> </Town> <PostalCode> <xsl:value-of select="$data/Address/Postcode"/> </PostalCode> </xsl:element> </xsl:template> </xsl:stylesheet> When i try to run the style sheet it's complaining to me that I need to: To use a result tree fragment in a path expression, either use exsl:node-set() or specify version 1.1 I don't want to go to version 1.1.. So does anyone know how to get the exsl:node-set() working for the above example? Or if someone knows of a better way to apply the same template to 2 different sections then that would also really help me out? Thanks Dave

  Read the article

• JSF command button attribute is transferred incorrectly

  - by Oleg Rybak

  I have following code in jsf page, backed by jsf managed bean <h:dataTable value="#{poolBean.pools}" var="item"> <h:column> <f:facet name="header"> <h:outputLabel value="Id"/> </f:facet> <h:outputText value="#{item.id}"/> </h:column> <h:column> <f:facet name="header"> <h:outputLabel value="Start Range"/> </f:facet> <h:inputText value="#{item.startRange}" required="true"/> </h:column> <h:column> <f:facet name="header"> <h:outputText value="End Range"/> </f:facet> <h:inputText value="#{item.endRange}" required="true"/> </h:column> <h:column> <f:facet name="header"> <h:outputText value="Pool type"/> </f:facet> <h:selectOneMenu value="#{item.poolType}" required="true"> <f:selectItems value="#{poolBean.poolTypesMenu}"/> </h:selectOneMenu> </h:column> <h:column> <f:facet name="header"/> <h:commandButton id="ModifyPool" actionListener="#{poolBean.updatePool}" image="img/update.gif" title="Modify Pool"> <f:attribute name="pool" value="#{item}"/> </h:commandButton> </h:column> </h:dataTable> This code fragment is dedicated to editing come collection of items. Each row of the table contains "edit" button that submits changed values of the row to the server. It has the item itself as an attribute. Submit is performed by calling actionListener method in the backing managed bean. This code runs correctly on Glassfish v 2.1 But when the server was updated to Glassfish v 2.1.1, the attribute stopped to be passed correctly. Instead of passing edited item (when we change the values in table row, we are actually changing the underlying object fields), the source item is submitted to server, i.e. the item that was previously given to the page. All the changes that were made on the page are discarded. I tried to update jsf version from 1.2_02 to 1.2_14 (we are using jsf RI), but it had no effect. Perhaps anyone came across the same problem? Any help and suggestions will be appreciated.

  Read the article

• My google map android app keeps crashing

  - by Manny264

  I have followed about two tutorials from vogella and some other tutorial that looked similar...very similar but to no avail. I load the app on my nexus 7 and it just crashes "Unfortunately MyMapView has stopped working" on launch.This is the manifest: ` <uses-sdk android:minSdkVersion="17" android:targetSdkVersion="17" /> <uses-feature android:glEsVersion="0x00020000" android:required="true"/> <uses-permission android:name="android.permission.INTERNET" /> <uses-permission android:name="android.permission.ACCESS_NETWORK_STATE" /> <uses-permission android:name="android.permission.ACCESS_COARSE_LOCATION" /> <uses-permission android:name="android.permission.ACCESS_FINE_LOCATION" /> <uses-permission android:name="android.permission.WRITE_EXTERNAL_STORAGE"/> <uses-permission android:name="com.google.android.providers.gsf.permission.READ_GSERVICES"/> <application android:allowBackup="true" android:icon="@drawable/ic_launcher" android:label="@string/app_name" android:theme="@style/AppTheme" > <uses-library android:name="com.google.android.maps" /> <activity android:name="com.macmozart.mymapview.MainActivity" android:label="@string/app_name" > <intent-filter> <action android:name="android.intent.action.MAIN" /> <category android:name="android.intent.category.LAUNCHER" /> </intent-filter> </activity> <meta-data android:name="com.google.android.maps.v2.API_KEY" android:value="AIzaSyBZ1Bt7rjB863Jy-B05zls6k8XZsBGQ6-4" /> </application> ` Followed by my main layout: <fragment android:id="@+id/map" android:layout_width="match_parent" android:layout_height="match_parent" class="com.google.android.gms.maps.MapFragment" /> and finally my java class: package com.macmozart.mymapview; import android.app.Activity; import android.os.Bundle; import com.google.android.gms.maps.CameraUpdateFactory; import com.google.android.gms.maps.GoogleMap; import com.google.android.gms.maps.MapFragment; import com.google.android.gms.maps.model.BitmapDescriptorFactory; import com.google.android.gms.maps.model.LatLng; import com.google.android.gms.maps.model.Marker; import com.google.android.gms.maps.model.MarkerOptions; import com.google.android.maps.*; public class MainActivity extends Activity { static final LatLng HAMBURG = new LatLng(53.558, 9.927); static final LatLng KIEL = new LatLng(53.551, 9.993); private GoogleMap map; @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); map = ((MapFragment) getFragmentManager().findFragmentById(R.id.map)) .getMap(); if (map != null) { Marker hamburg = map.addMarker(new MarkerOptions() .position(HAMBURG).title("Hamburg")); Marker kiel = map.addMarker(new MarkerOptions() .position(KIEL) .title("Kiel") .snippet("Kiel is cool") .icon(BitmapDescriptorFactory .fromResource(R.drawable.ic_launcher))); map.moveCamera(CameraUpdateFactory.newLatLngZoom(HAMBURG, 15)); // Zoom in, animating the camera. map.animateCamera(CameraUpdateFactory.zoomTo(10), 2000, null); } } } Any idea what im doing wrong I really need this to work

  Read the article

• Cross Browser Issue

  - by dazedandconfused

  My background is in WinForms programming and I'm trying to branch out a bit. I'm finding cross-browser issues a frustrating barrier in general, but have a specific one that I just can't seem to work through. I want to display an image and place a semi-transparent bar across the top and bottom. This isn't my ultimate goal, of course, but it demonstrates the problem I'm having ina a relatively short code fragment so let's go with it. The sample code below displays as intended in Chrome, Safari, and Firefox. In IE8, the bar at the bottom doesn't appear at all. I've researched it for hours but just can't seem to come up with the solution. I'm sure this is some dumb rookie mistake, but gotta start somewhere. Code snippet... <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <title></title> <script type="text/javascript" language="javascript"> </script> <style type="text/css"> .workarea { position: relative; border: 1px solid black; background-color: #ccc; overflow: hidden; cursor: move; -moz-user-focus: normal; -moz-user-select: none; unselectable: on; } .semitransparent { filter: alpha(opacity=70); -moz-opacity: 0.7; -khtml-opacity: 0.7; opacity: 0.7; background-color: Gray; } </style> </head> <body style="width: 800px; height: 600px;"> <div id="workArea" class="workarea" style="width: 800px; height: 350px; left: 100px; top: 50px; background-color: White; border: 1px solid black;"> <img alt="" src="images/TestImage.jpg" style="left: 0px; top: 0px; border: none; z-index: 1;" /> <div id="topBar" class="semitransparent" style="position: absolute;width: 800px; height: 75px; left: 0px; top: 0px; min-height: 75px; border: none; z-index: 2;" /> <div id="bottomBar" class="semitransparent" style="position: absolute; width: 800px; height: 75px; left: 0px; top: 275px; min-height: 75px; border: none; z-index: 2;" /> </div> </body> </html>

  Read the article

• maven scm plugin deleting output folder in every execution

  - by Udo Fholl

  Hi all, I need to download from 2 different svn locations to the same output directory. So i configured 2 different executions. But every time it executes a checkout deletes the output directory so it also deletes the already downloaded projects. Here is a sample of my pom.xml: <profiles> <profile> <id>checkout</id> <activation> <property> <name>checkout</name> <value>true</value> </property> </activation> <build> <plugins> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-scm-plugin</artifactId> <version>1.3</version> <configuration> <username>${svn.username}</username> <password>${svn.pass}</password> <checkoutDirectory>${path}</checkoutDirectory> <skipCheckoutIfExists /> </configuration> <executions> <execution> <id>checkout_a</id> <configuration> <connectionUrl>scm:svn:https://host_n/folder</connectionUrl> <checkoutDirectory>${path}</checkoutDirectory> </configuration> <phase>process-resources</phase> <goals> <goal>checkout</goal> </goals> </execution> <execution> <id>checkout_b</id> <configuration> <connectionUrl>scm:svn:https://host_l/anotherfolder</connectionUrl> <checkoutDirectory>${path}</checkoutDirectory> </configuration> <phase>process-resources</phase> <goals> <goal>checkout</goal> </goals> </execution> </executions> </plugin> </plugins> </build> </profile> Is there any way to prevent the executions to delete the folder ${path} ? Thank you. PS: I cant format the pom.xml fragment correctly, sorry!

  Read the article

• opengl 3d texture issue

  - by user1478217

  Hi i'm trying to use a 3d texture in opengl to implement volume rendering. Each voxel has an rgba colour value and is currently rendered as a screen facing quad.(for testing purposes). I just can't seem to get the sampler to give me a colour value in the shader. The quads always end up black. When I change the shader to generate a colour (based on xyz coords) then it works fine. I'm loading the texture with the following code: glGenTextures(1, &tex3D); glBindTexture(GL_TEXTURE_3D, tex3D); unsigned int colours[8]; colours[0] = Colour::AsBytes<unsigned int>(Colour::Blue); colours[1] = Colour::AsBytes<unsigned int>(Colour::Red); colours[2] = Colour::AsBytes<unsigned int>(Colour::Green); colours[3] = Colour::AsBytes<unsigned int>(Colour::Magenta); colours[4] = Colour::AsBytes<unsigned int>(Colour::Cyan); colours[5] = Colour::AsBytes<unsigned int>(Colour::Yellow); colours[6] = Colour::AsBytes<unsigned int>(Colour::White); colours[7] = Colour::AsBytes<unsigned int>(Colour::Black); glTexImage3D(GL_TEXTURE_3D, 0, GL_RGBA, 2, 2, 2, 0, GL_RGBA, GL_UNSIGNED_BYTE, colours); The colours array contains the correct data, i.e. the first four bytes have values 0, 0, 255, 255 for blue. Before rendering I bind the texture to the 2nd texture unit like so: glActiveTexture(GL_TEXTURE1); glBindTexture(GL_TEXTURE_3D, tex3D); And render with the following code: shaders["DVR"]->Use(); shaders["DVR"]->Uniforms["volTex"].SetValue(1); shaders["DVR"]->Uniforms["World"].SetValue(Mat4(vl_one)); shaders["DVR"]->Uniforms["viewProj"].SetValue(cam->GetViewTransform() * cam->GetProjectionMatrix()); QuadDrawer::DrawQuads(8); I have used these classes for setting shader params before and they work fine. The quaddrawer draws eight instanced quads. The vertex shader code looks like this: #version 330 layout(location = 0) in vec2 position; layout(location = 1) in vec2 texCoord; uniform sampler3D volTex; ivec3 size = ivec3(2, 2, 2); uniform mat4 World; uniform mat4 viewProj; smooth out vec4 colour; void main() { vec3 texCoord3D; int num = gl_InstanceID; texCoord3D.x = num % size.x; texCoord3D.y = (num / size.x) % size.y; texCoord3D.z = (num / (size.x * size.y)); texCoord3D /= size; texCoord3D *= 2.0; texCoord3D -= 1.0; colour = texture(volTex, texCoord3D); //colour = vec4(texCoord3D, 1.0); gl_Position = viewProj * World * vec4(texCoord3D, 1.0) + (vec4(position.x, position.y, 0.0, 0.0) * 0.05); } uncommenting the line where I set the colour value equal to the texcoord works fine, and makes the quads coloured. The fragment shader is simply: #version 330 smooth in vec4 colour; out vec4 outColour; void main() { outColour = colour; } So my question is, what am I doing wrong, why is the sampler not getting any colour values from the 3d texture? [EDIT] Figured it out but can't self answer (new user): As soon as I posted this I figured it out, I'll put the answer up to help anyone else (it's not specifically a 3d texture issue, and i've also fallen afoul of it before, D'oh!). I didn't generate mipmaps for the texture, and the default magnification/minification filters weren't set to either GL_LINEAR, or GL_NEAREST. Boom! no textures. Same thing happens with 2d textures.

  Read the article

< Previous Page | 28 29 30 31 32 33 34  | Next Page >