Search Results

Search found 2794 results on 112 pages for 'peu ping'.

Page 32/112 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• What are the requirements for Windows Remote Assistance over Teredo?

  - by Jens

  I try to get the Windows 7 (or Vista) remote assistance feature to work, without using UPnP on the novices computer. After enabling Teredo on the expert's computer (that is in a corporate network, and therefore has teredo disabled by default), I tried to connect to the novice both using Easy Connect and the invitation file with no success. My triubleshooting included the following (so far). A connection to the novice from my home pc was successful, hinting at a misconfiguration on the experts side. Both computers have a "qualified" connection to the Teredo Server. Both computers have a valid Teredo IP, access to the Global_ PNRP cloud and can resolve names registered with PNRP on the other computer. The expert can resolve the PNRP Id automatically generated with an Easy Connect help request Both computers can ping the other's PNRP name. Both computers can ping the other's Teredo IP Address using ping -6 Now, I am a little stumped. I expected Remote Assistance to work at this point, since my corporate firewall has no Teredo filtering. What could RA cause not to work in this setting? Thanks in advance!

  Read the article

• DNS Issue- Nameserver Issue

  - by Master-Man

  I setup new server on centos 5.3 and configure dns and hostnam using WHM. I also register my new nameservers with my domain registrar with ns1.example.com and ns2.example.com. But i am unable to ping hostname and NS. ping pc2.example.com or ping ns1.example.com I received the below email from server. IMPORTANT: Do not ignore this email. Your hostname (pc2.example.com) could not be resolved to an IP address. This means that /etc/hosts is not set up correctly, and/or there is no dns entry for pc2.example.com. Please be sure that the contents of /etc/hosts are configured correctly, and also that there is a correct 'A' entry for the domain in the zone file. Some or all of these problems can be caused by /etc/resolv.conf being setup incorrectly. Please check that file if you believe everything else is correct. You may be able to automatically correct this problem by using the 'Add an A entry for your hostname' option under 'Dns Functions' in your Web Host Manager. When I issue the command root@pc[~]# host pc2.example.com I receive the below error that Host pc2.example.com not found: 3(NXDOMAIN) I added A entries for hostname and Nameservers but nothing replies. Its almost more than 72 hours for setting & registering nameservers and dns configurations. thanks,

  Read the article

• XenServer VMs can't reach network

  - by toto

  I'm currently trying to setup a small cloud architecture , I'm using in the installation CloudStack 2.2.14 which need two node : a management server (as node1) to provision the cloud and a hyperviser XenServer 5.6 SP2 to host the VMs (as node2). I succeded to create both node1 and node2 into an ESXi 5 VMWare as VMs. So The ESXi 5 is hosting two VMs node1 + node2 , and node2 which is the XenServer will host also VMs (such as ubuntu or Centos). Both node1 and node2 can ping each other and can get the internet connection from Esxi5 ,but My problem is : that VMs into the node2(XenServer) can't reach the network (can't ping node1 or Esxi or get an internet connection but they can ping VMs IN the node2(XenServer). So I tried to: 1-Setup a DHCP server as node3 in ESXi5 and connect node2(Xenserver) to him , but always the VMs into to node2 can't reach the outer network. 2-Setup a DCHP server into node2 , but always the same problem. So , 1-is there any other configuration i'm missing in node2 (considering that I'm sure about DNS , GW , NETMASK configuration)?. 2-Is it the problem because i'm Creating VMs into node2(XenSever) which is a VM into ESXi 5 ?

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

• Two hosts on same subnet can't see each other

  - by Joey Hewitt

  I've got two routers with two separate public IP addresses on the same subnet, but I can't get them to talk to each other. Both are connected to the internet (ISP-provided gateway) via Ethernet ports provided by the landlord, but I don't have access to or knowledge of how those are physically connected or the protocols used to get back to the ISP. I can ping either from the outside, but they can't ping each other. Traceroutes in and out look the same, and they receive the same gateway over DHCP. I can ping other IPs on the subnet, so I assume this is not any sort of intentional isolation for security/privacy. Since I'm in a setup where my landlord provides internet and we don't have contact with the ISP, I can't really ask the ISP for help (doubt the landlord would know much either.) The situation is similar to the diagram at this question, but instead of the two servers, there's another router coming off the (presumed) switch, and I don't have access to the switch. I've tried giving them static routes to each other with the ISP internet gateway as the gateway, but that's not working. One is a Linksys WRT54GL running DD-WRT, the other is a Netgear WGR614v7, although I could get something more capable if necessary. I'd like to keep them each connected directly to the ISP on their WAN ports, but I can have an ethernet cable between them if necessary - I'm wondering if there's a way without that, and if there isn't, I'd appreciate advice on how to get that working. Sorry this is so nitpicky; there are reasons for all the constraints, but they don't apply to the real question, so I left them out. ;) Thank you!

  Read the article

• Only tunnel certain applications via OpenVPN

  - by jinjin

  Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

  Read the article

• Can't get DNS Alias work on Ubuntu 10.04 with Apache 2

  - by Johnny

  I want to use the DNS Alias to configure one of my domain pointing to a specific directory on the server. Here is what I've done: Change the IP address in domain setting, and it works $ ping www.example.com PING example.com (124.205.62.xxx): 56 data bytes 64 bytes from 124.205.62.xxx: icmp_seq=0 ttl=48 time=53.088 ms 64 bytes from 124.205.62.xxx: icmp_seq=1 ttl=48 time=52.125 ms ^C --- example.com ping statistics --- 2 packets transmitted, 2 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 52.125/52.606/53.088/0.482 ms Add sites-available and sites-enabled $ ls -l /etc/apache2/sites-available/ total 16 -rw-r--r-- 1 root root 948 2010-04-14 03:27 default -rw-r--r-- 1 root root 7467 2010-04-14 03:27 default-ssl -rw-r--r-- 1 root root 365 2010-06-09 18:27 example.com $ ls -l /etc/apache2/sites-enabled/ total 0 lrwxrwxrwx 1 root root 26 2010-06-09 15:46 000-default -> ../sites-available/default lrwxrwxrwx 1 root root 33 2010-06-09 18:17 001-example.com -> ../sites-available/example.com But it doesn't work and when I open the browser for www.example.com, it shows an 111 error: The following error was encountered: Connection to 124.205.62.48 Failed The system returned: (111) Connection refused Here is how example.com's config: $ cat /etc/apache2/sites-enabled/001-example.com <virtualhost *:80> DocumentRoot "/vhosts/example.com/htdocs/" ServerName www.example.com ServerAlias example.com <Location /> Order Deny,Allow Deny from None Allow from all </Location> #Include /etc/phpmyadmin/apache.conf ErrorLog /vhosts/example.com/logs/error.log CustomLog /vhosts/example.com/logs/access.log combined Could you please tell me how to solve this?

  Read the article

• Setup windows 2012 AD in Hyper-V for a Test environment

  - by hub

  Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

  Read the article

• Virtual IPv6 Network between VirtualBox VMs

  - by Ben

  I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

  Read the article

• Not able to access Silverlight.net and ONLY Silverlight.net - All other domains work!

  - by Sootah

  Alrighty folks, I have an extremely odd problem. I am able to surf the web fine with one odd (and really annoying at the moment) exception: Microsoft's Silverlight.net. Every other site that I go to works just fine. This is quite frustrating because I'm in the middle of programming a web app in Silverlight 4.0, and whenever I do a search for any code examples, tutorials, or whatnot at least 50% of the results are hosted in the silverlight.net forums. The error message that I get is: Oops! Google Chrome could not find www.silverlight.net It doesn't work in my other browsers either (both IE and FireFox). What's odd, is that while the error message would lead me to assume it's a DNS error, I can ping the URL just fine. C:\Users\The Doot>ping silverlight.net Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Ping statistics for 206.72.125.201: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 103ms, Maximum = 110ms, Average = 106ms I've checked my HOSTS file, and there's nothing that refers to ANY Microsoft URL in there. What could be causing this!?? More importantly, how do I fix it? Just for kicks, I've even included the results of a traceroute here for your enjoyment. OS: Windows 7 Ultimate Thanks in advance! -Sootah

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• Home Network Stopped Working

  - by James

  I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

  Read the article

• Trying to communicate between virtual servers on the same host through ipv6

  - by Daniele Testa

  I am running KVM on a host with 2 virtual servers. Each virtual server has a own bridge interface on the host VPS1 has br1 VPS2 has br2 Each virtual server has a own ipv4 and a ipv6. The virtual servers has no problem communicating with internet or with eachother through ipv4. However, with ipv6, they can only communicate with internet and NOT with eachother. The host can ping the 2 virtual servers without any problems, but they cannot ping eachother. iptables has been set to ACCEPT on all chains, so it is not the problem. VPS1 has ipv6 = 2a01:4f8:xxx:xxx::10 VPS2 has ipv6 = 2a01:4f8:xxx:xxx::5 the host has the following routes set: ip route add 2a01:4f8:xxx:xxx::10 dev br1 ip route add 2a01:4f8:xxx:xxx::5 dev br2 When I do a ping from VPS2 to VPS1, I see the following on the host: tcpdump -i br1 15:32:27.704404 IP6 2a01:4f8:xxx:xxx::10 > ff02::1:ff00:5: ICMP6, neighbor solicitation, who has 2a01:4f8:xxx:xxx::5, length 32 So it seems like the host is seeing the request coming from VPS1 on br1. But for some reason, it does not forward it to br2. Instead it is asking where the destination IP is through ipv6 multicast. Anyone has a clue what is going on? I find this very strange, as it is working fine with ipv4 with the exact same settings and routes.

  Read the article

• Onboard Ethernet suddenly stopped working to router

  - by AfterschoolHobbist

  Hey guys, yesterday I have a sudden problem of my Ethernet connection to my router. My computer is a Pendium 4 with Window XP SP3 running on it and it was working fine earlier in the day, but yesterday night was the start of the problem. My computer is unable to ping to the router and to any other website and unable to get internet connection. As beside it was connected to a hub, I directly connected it to the router directly and the same problem occurred, being unable to ping to the router (and connecting to it) and still no internet access. My directly connected to the modem and the problem still persisted. For each connection, I connected it to my computer and my laptop and my laptop was able to connect, while my desktop computer was unable. I wondered if it was a OS issue and ran a live Ubuntu CD to see if Ubuntu was able to connect to the internet, but the issue persisted and I was unable to get internet access. I then set my router's lease time to 1 hour and waited. After 1 hour, the lease for my computer was removed and I hoped this worked, but it didn't work, but something strange is acting up. My desktop computer is still unable to ping to the router or connect to the internet, but for some reason, my router and desktop computer is still able to contact each other by providing a lease of an local ip address. The router record of a lease to my desktop computer, and when I do ipconfig, my desktop also recognize that it has been provided a local ip address. I have concluded that this is a hardware issue and the only solution to fix this is to by a network card adapter, but I am wondering if anyone has any solutions that could explain why this happen, why my mac address is 01-23-45-67-89-ab, and is there any way to fix it without buying a new network card? Thanks in advance.

  Read the article

• Separated virtual networks with same subnet range with 2 interface

  - by Coolpet

  I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

  Read the article

• Logging communication between two VMs

  - by sYnfo

  Hi, I'm trying to set up "malware lab" described in this paper. So far, I've set up Windows guest system, adding one Host-only Network adapter, and setting this (sorry if the names aren't exactely correct, I don't have an english language version): - IP Address - 10.0.0.3 - Subnet mask - 255.255.255.0 - Default gateway - not set - Preferred DNS - 10.0.0.4 - Alternate DNS - not set And a Linux guest system - Ubuntu 9.04 - with two Network adapters - Bridged (eth0) and Host-only (eth1), and setting eth1 IP Address to 10.0.0.4, leaving the eth0 to be set by DHCP. Then, I have configured iptables as described in the paper, ie.: iptables -F -t nat iptables -F -t mangle iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -A PREROUTING -i eth0 -j ACCEPT iptables -t mangle -A PREROUTING -p udp -i eth1 -d 10.0.0.3 --dport 53 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 --dport 80 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 -d 10.0.0.3 --dport 6000:7000 -j ACCEPT iptables -t mangle -A PREROUTING -i eth1 -j ULOG iptables -t mangle -A PREROUTING -i eth1 -j DROP Now, when I try to ping the windows system from within the Linux system, it does not reply, I guess thats perfectly normal, because iptables is blocking ping responce. Same when I try to ping the Linux system from within the Windows. But when I try to access any web page from within the Windows system, I would expect that this action should get logged by iptables. But thing is, I don't see any of that kind of lines in log file (If I am looking in the right place, that is. :) It is at /var/log/messages, isn't it?). So, what do you think might be the problem here? I should note, that this is the first time I'm using linux, so don't expect ANY working knowledge of Linux at all... :) Also, since english is not my mother tongue, feel free to point out any gramatical mistakes... :) Thanks for any advice.

  Read the article

• Troubleshooting DTCPing Errors

  - by JimmyP

  So I am running DTC ping between 2 machines on our network and am getting the following error ++++++++++++++++++++++++++++++++++++++++++++++ DTCping 1.9 Report for WEB2 ++++++++++++++++++++++++++++++++++++++++++++++ RPC server is ready ++++++++++++Validating Remote Computer Name++++++++++++ 03-03, 13:39:45.099-->Start DTC connection test Name Resolution: internal-->10.20.3.236-->internal.something 03-03, 13:39:45.114-->Start RPC test (WEB2-->internal) Problem:fail to invoke remote RPC method Error(0x6BA) at dtcping.cpp @303 -->RPC pinging exception -->1722(The RPC server is unavailable.) RPC test failed I have also run RPC ping where I get what I beleive is the same error: C:\Program Files\Windows Resource Kits\Tools>rpcping -s internal Exception 1722 (0x000006BA) Number of records is: 4 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1722 Detection location is 323 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1237 Detection location is 313 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 311 Flags is 0 NumberOfParameters is 3 Long val: 135 Pointer val: 0 Pointer val: 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 318 Flags is 0 NumberOfParameters is 0 I'm pretty sure that the exception number 1722 is the key but I can't find any info about it. There may be a firewall with ports that need opening between the machines which I am checking with our sys admins now. But I can do a regular ping between the machines. Other than that I am reading a lot of articles talking about OS services and components I know nothing about and am having trouble finding any info on. Can anyone shed any light on this? FYI the machine is running Windows Server 2003 RS SP2.

  Read the article

• Configuring two subnets with two NICS. Access from a NAS to the internet

  - by archipestre

  I am having trouble configuring my NAS. I have a DSL router with WIFI (192.168.1.1) in my flatmates room. In my room I have a server with two NICS: 1) wlan0 (192.168.1.2) that connects to the DSL router via wireless 2) em1 (192.168.0.1) that connects to the NAS (192.168.0.20) with a crossover cable. I have Fedora 17 and I have enable packet forwarding. My IP configuration is as follows: WLAN0 inet 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 EM1 inet 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 My routing table looks like: Destination Gateway G enmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 em1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 I have enable a static route in the DSL server: Status Network Destination Subnet Mask Interface Gateway Remove Edit Active 192.168.0.0 255.255.255.0 LAN 192.168.1.2 From my server I can ping the DSL router and the NAS. From the NAS I can ping both NICS of the server. However the NAS is unable to ping the DSL router or any address in the Internet. Any idea of what is wrong. Thank you in advance

  Read the article

• Sources of latency in sending-receiving tcp/udp packets in linux

  - by osgx

  Hello What are sources of latency in process of sending/receiving tcp/udp packets in linux 2.6 ? I want to know a latency sources in "ping-pong" latency tests. There are some rather good papers of ethernet latency, but they cover only latency sources in the wire and switch (and rather cursory, only for specific switch). What steps of processing does follow a packet? Papers with deep latency analysis of usual ping (icmp) will be useful too. I rely on community :)

  Read the article

• java.util.logging: how to suppress date line

  - by andrews

  I'm trying to suppress output of the date line durinng logging when using the default logger in java.util.logging. For example, here is a typical output: Jun 1, 2010 10:18:12 AM gamma.utility.application info INFO: ping: db-time=2010-06-01 10:18:12.0, local-time=20100601t101812, duration=180000 Jun 1, 2010 10:21:12 AM gamma.utility.application info INFO: ping: db-time=2010-06-01 10:21:12.0, local-time=20100601t102112, duration=180000 I would like to get rid of the Jun 1, 2010... lines, they just clutter my log output. How can I do this?

  Read the article

• run tomcat server on lan

  - by pravin

  I am running a server on Windows XP SP2 computer . Lets call it computer_1. The ip address of computer is 192.168.1.2 Now I have another computer ( computer_2) on the lan with ip address 192.168.1.3 I want to access the site on computer_1 from computer_2. comupter_2 can ping computer_1 (ping 192.168.1.2 works) But when I type http://192.168.1.2 in the browser of computer_2, nothing happens. I want to access the site on comupter_1 from computer_2 Please help.

  Read the article

• How to get status code of a POST with Asp.Net HttpWebRequest

  - by Hasan Gürsoy

  I'm trying to ping Google when my web site's sitemap is updated but I need to know which status code does Google or any other service returns. My code is below: HttpWebRequest rqst = (HttpWebRequest)WebRequest.Create("http://search.yahooapis.com/ping?sitemap=http%3a%2f%2fhasangursoy.com.tr%2fsitemap.xml"); rqst.Method = "POST"; rqst.ContentType = "text/xml"; rqst.ContentLength = 0; rqst.Timeout = 3000; rqst.GetResponse();

  Read the article

• How to make Google reader feed public.

  - by user356213

  I am setting up my Google reader so the rss feed posts to my Ping.fm account via the ping.fm superfeeder module. I cant work out how to make my Google reader feed public. please help

  Read the article

• Get derived class type from a base's class static method

  - by Marco Bettiolo

  Hi, i would like to get the type of the derived class from a static method of its base class. How can this be accomplished? Thanks! class BaseClass { static void Ping () { Type t = this.GetType(); // should be DerivedClass, but it is not possible with a static method } } class DerivedClass : BaseClass {} // somewhere in the code DerivedClass.Ping();

  Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >