Search Results

Search found 920 results on 37 pages for 'rev'.

Page 32/37 | < Previous Page | 28 29 30 31 32 33 34 35 36 37  | Next Page >

• RTL8188CE doesn't connect to any wifi access points

  - by Drakmail

  I'm using network manager to connect. Also, tryed iwconfig. Results are same. I even try to connect to open access point — results are same. More information: Drakmail@thinkpad-x220:~$ lspci | grep Network | grep -v Ethernet 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Drakmail@thinkpad-x220:~$ uname -a Linux thinkpad-x220 3.1.0 #1 SMP PREEMPT Wed Oct 26 02:19:49 UTC 2011 x86_64 Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz GenuineIntel GNU/Linux Drakmail@thinkpad-x220:~$ dmesg | tail -n 10 [ 846.901574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 906.812461] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 966.728810] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1026.639676] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1030.925574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin At this moment I try to connect to open wifi ap: [ 1031.252403] wlan0: direct probe to 00:24:8c:55:fa:ed (try 1/3) [ 1031.451943] wlan0: direct probe to 00:24:8c:55:fa:ed (try 2/3) [ 1031.651658] wlan0: direct probe to 00:24:8c:55:fa:ed (try 3/3) [ 1031.851354] wlan0: direct probe to 00:24:8c:55:fa:ed timed out [ 1086.544960] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin My distribution: Drakmail@thinkpad-x220:~$ cat /etc/*version AgiliaLinux release 8.0.0 (Sammy) (Something between Slackware and Archlinux). Also, I saw that wifi module to often trying to load a firmware file. Any ideas what it would be?

  Read the article

• Sound doesn't work anymore after replacing RAM

  - by thejh

  Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

  Read the article

• XBMC remote control key repeat

  - by Amigable Clark Kant

  Those who have used XBMC with a WiFi remote, such as an Android or iOS device with the official XBMC remotes, have probably seen this at one time or another: your remote stops working, when you press a key, that key is repeated very fast. Sometimes you can break the key repeat loop by pressing that same key again. Sometimes (as this particular morning) you can not. This problem has existed for literally years (it even occurs on the old XBOX only builds) but there seems to be no definite explanation as to what is causing it. I am asking for a workaround. (If you Google, you can find threads were people are ridiculed for bringing up this problem, which is one reason I ask here instead of on the official forums. Also the fact that this problem has persisted for so many years.) I am running, right now, XBMCBuntu Live Eden and the latest official iOS remote. Although, I have seen this problem on all combinations of remotes and XBMC versions I have tried over the years, which are many. (XBMC on Windows, Linux, OSX, remotes on Android and iOS.) Link to bug #136 for the Android remote. It's marked as "fixed" as of client version 636, but the problem is seen again in rev 730. Go figure. There is something fundamentally wrong with how keypresses are sent from the various remotes to XBMC, since this problem is seen across time, XBMC versions and iOS/Android.

  Read the article

• Mercurial confusion - commit / push, backouts

  - by Madmanguruman

  I'm trying to set up a repository on a shared filesystem. I'm using Mercurial 2.1.2 on a Windows-based architecture. I start with an empty folder on the shared filesystem and create a repository in it. After this, I dump in the baseline files, and add them to versioning, then commit the changes. I then clone the repository to my local hard drive. I then make a change in my local repository, commit it, then push back to the shared filesystem repository. The shared repo graph I get in TortoiseHG looks strange (to me). This is the shared repo: This is the local repo: On the shared repo, the working directory always shows up on the top, then the graph goes 'down' to rev. 0 then back 'up' again through various revisions. It looks to me like I have two different branches, even though everything is on the default branch. Also, that 'top' revision always says "* Working Directory * Not a head revision!" I noticed that in my local repository, I don't get that dangling working directory at the top of the list - everything is in one branch. I also noticed that on my local repository, I can back out the tip revision with no problem. On the shared filesystem repository, I cannot, since I get an error ("Cannot backout change on a different branch"). How can this be? Aren't they supposed to be identical to each other? Am I fundamentally doing something wrong?

  Read the article

• Cisco 7206vxr cpu reducing

  - by naimson

  I have a 7206VXR (NPE-G2) . At the rate of 140 kpps i gain 80% of cpu . So i looking for ways how to reduce it? So i want to turn off netflow(but don't want to this,monitoring is highly important for me), but it will give me only 10-20% ? At this moment with 84kpps i have 58% sh processes cpu sorted give me this. PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 109 163534600 537236763 304 35.38% 32.83% 16.85% 0 IP Input 67 829396 52280 15864 0.15% 0.01% 0.00% 0 Per-minute Jobs 68 5542736 3053476 1815 0.15% 0.18% 0.16% 0 Per-Second Jobs 51 635852 1116315 569 0.07% 0.03% 0.02% 0 Net Background 329 120396 4607274 26 0.07% 0.00% 0.00% 0 EIGRP-IPv4 Hello 105 50508 95032488 0 0.07% 0.05% 0.05% 0 IPAM Manager 6 4068580 476916 8531 0.00% 0.07% 0.05% 0 Check heaps 7 7768 3634 2137 0.00% 0.00% 0.00% 0 Pool Manager 8 0 1 0 0.00% 0.00% 0.00% 0 DiscardQ Backgro 10 8 708 11 0.00% 0.00% 0.00% 0 WATCH_AFS 5 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers 12 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea 9 0 2 0 0.00% 0.00% 0.00% 0 Timers 11 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio 13 296 610532 0 0.00% 0.00% 0.00% 0 IPC Event Notifi 16 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager 17 3584 2980311 1 0.00% 0.00% 0.00% 0 IPC Periodic Tim 4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN 19 0 1 0 0.00% 0.00% 0.00% 0 IPC Process leve 20 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager 21 96 174453 0 0.00% 0.00% 0.00% 0 IPC Check Queue 14 4 50890 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach 3 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ 24 756 305371 2 0.00% 0.00% 0.00% 0 IPC Keep Alive M 25 2340 610561 3 0.00% 0.00% 0.00% 0 IPC Loadometer 22 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat RX Cont 15 0 1 0 0.00% 0.00% 0.00% 0 IPC Session Serv 18 1620 2980310 0 0.00% 0.00% 0.00% 0 IPC Deferred Por 29 0 1 0 0.00% 0.00% 0.00% 0 Exception contro sh run(greped): http://pastie.org/5483194 Hardware: c7200p-adventerprisek9-mz.151-4.M1.bin Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 2xxxxxxx MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2 6 slot VXR midplane, Version 2.1

  Read the article

• Hourly SQL Server 2005 Slowness (Possibly caused by SYSTEM)

  - by Zorlack

  We're trying to diagnose the cause of slowness on our Database server. We're running the latest rev SQL Server 2005 on Windows 2008x64. The behavior that we're seeing is this: We see the SYSTEM process spike one of the CPUs for about 2 minutes, during this time SQL server slows down by a factor of 10. The slowness lasts until SYSTEM is done, then in an hour everything starts again. During these slowdowns disk writes don't spike, paging doesn't spike, the only noticeable precursor we see is that SYSTEM maxes out one of the sixteen (HT)CPUs. Note that this doesn't happen at the top of the hour, it just happens once an hour, and it shifts a bit depending on the length of the incident. At the moment this is causing intermittent slowdowns, but when the server is really busy it can cause Worker Thread starvation. The server is a Dual Quad Dell R710 with 96GB of RAM and RAID10 data/log disks. Has anyone experienced this kind of problem? Does anyone know where we should look? Edit: SQL Server Version is 9.0.4035

  Read the article

• Debian squeeze keyboard and touchpad not working / detected on laptop

  - by Esa

  They work before gdm3 starts. a connected mouse also stops working, but functions after removal and re-plug. no xorg.conf. log doesn't show any loading of drivers for kbd/touchpad [ 33.783] X.Org X Server 1.10.4 Release Date: 2011-08-19 [ 33.783] X Protocol Version 11, Revision 0 [ 33.783] Build Operating System: Linux 3.0.0-1-amd64 x86_64 Debian [ 33.783] Current Operating System: Linux sus 3.2.0-0.bpo.2-amd64 #1 SMP Sun Mar 25 10:33:35 UTC 2012 x86_64 [ 33.783] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-0.bpo.2-amd64 root=UUID=8686f840-d165-4d1e-b995-2ebbd94aa3d2 ro quiet [ 33.783] Build Date: 28 August 2011 09:39:43PM [ 33.783] xorg-server 2:1.10.4-1~bpo60+1 (Cyril Brulebois <[email protected]>) [ 33.783] Current version of pixman: 0.16.4 [ 33.783] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 33.783] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 33.783] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Mar 28 09:34:04 2012 [ 33.837] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 33.936] (==) No Layout section. Using the first Screen section. [ 33.936] (==) No screen section available. Using defaults. [ 33.936] (**) |-->Screen "Default Screen Section" (0) [ 33.936] (**) | |-->Monitor "<default monitor>" [ 33.936] (==) No monitor specified for screen "Default Screen Section". Using a default monitor configuration. [ 33.936] (==) Automatically adding devices [ 33.936] (==) Automatically enabling devices [ 34.164] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 34.164] Entry deleted from font path. [ 34.226] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/100dpi/:unscaled, /usr/share/fonts/X11/75dpi/:unscaled, /usr/share/fonts/X11/Type1, /usr/share/fonts/X11/100dpi, /usr/share/fonts/X11/75dpi, /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, built-ins [ 34.226] (==) ModulePath set to "/usr/lib/xorg/modules" [ 34.226] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 34.226] (II) Loader magic: 0x7d3ae0 [ 34.226] (II) Module ABI versions: [ 34.226] X.Org ANSI C Emulation: 0.4 [ 34.226] X.Org Video Driver: 10.0 [ 34.226] X.Org XInput driver : 12.2 [ 34.226] X.Org Server Extension : 5.0 [ 34.227] (--) PCI:*(0:1:5:0) 1002:9712:103c:1661 rev 0, Mem @ 0xd0000000/268435456, 0xf1400000/65536, 0xf1300000/1048576, I/O @ 0x00008000/256 [ 34.227] (--) PCI: (0:2:0:0) 1002:6760:103c:1661 rev 0, Mem @ 0xe0000000/268435456, 0xf0300000/131072, I/O @ 0x00004000/256, BIOS @ 0x????????/131072 [ 34.227] (II) Open ACPI successful (/var/run/acpid.socket) [ 34.227] (II) LoadModule: "extmod" [ 34.249] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so [ 34.277] (II) Module extmod: vendor="X.Org Foundation" [ 34.277] compiled for 1.10.4, module version = 1.0.0 [ 34.277] Module class: X.Org Server Extension [ 34.277] ABI class: X.Org Server Extension, version 5.0 [ 34.277] (II) Loading extension SELinux [ 34.277] (II) Loading extension MIT-SCREEN-SAVER [ 34.277] (II) Loading extension XFree86-VidModeExtension [ 34.277] (II) Loading extension XFree86-DGA [ 34.277] (II) Loading extension DPMS [ 34.277] (II) Loading extension XVideo [ 34.277] (II) Loading extension XVideo-MotionCompensation [ 34.277] (II) Loading extension X-Resource [ 34.277] (II) LoadModule: "dbe" [ 34.277] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so [ 34.299] (II) Module dbe: vendor="X.Org Foundation" [ 34.299] compiled for 1.10.4, module version = 1.0.0 [ 34.299] Module class: X.Org Server Extension [ 34.299] ABI class: X.Org Server Extension, version 5.0 [ 34.299] (II) Loading extension DOUBLE-BUFFER [ 34.299] (II) LoadModule: "glx" [ 34.299] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 34.477] (II) Module glx: vendor="X.Org Foundation" [ 34.477] compiled for 1.10.4, module version = 1.0.0 [ 34.477] ABI class: X.Org Server Extension, version 5.0 [ 34.477] (==) AIGLX enabled [ 34.477] (II) Loading extension GLX [ 34.477] (II) LoadModule: "record" [ 34.478] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so [ 34.481] (II) Module record: vendor="X.Org Foundation" [ 34.481] compiled for 1.10.4, module version = 1.13.0 [ 34.481] Module class: X.Org Server Extension [ 34.481] ABI class: X.Org Server Extension, version 5.0 [ 34.481] (II) Loading extension RECORD [ 34.481] (II) LoadModule: "dri" [ 34.481] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so [ 34.512] (II) Module dri: vendor="X.Org Foundation" [ 34.512] compiled for 1.10.4, module version = 1.0.0 [ 34.512] ABI class: X.Org Server Extension, version 5.0 [ 34.512] (II) Loading extension XFree86-DRI [ 34.512] (II) LoadModule: "dri2" [ 34.512] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so [ 34.515] (II) Module dri2: vendor="X.Org Foundation" [ 34.515] compiled for 1.10.4, module version = 1.2.0 [ 34.515] ABI class: X.Org Server Extension, version 5.0 [ 34.515] (II) Loading extension DRI2 [ 34.515] (==) Matched ati as autoconfigured driver 0 [ 34.515] (==) Matched vesa as autoconfigured driver 1 [ 34.515] (==) Matched fbdev as autoconfigured driver 2 [ 34.515] (==) Assigned the driver to the xf86ConfigLayout [ 34.515] (II) LoadModule: "ati" [ 34.706] (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so [ 34.724] (II) Module ati: vendor="X.Org Foundation" [ 34.724] compiled for 1.10.3, module version = 6.14.2 [ 34.724] Module class: X.Org Video Driver [ 34.724] ABI class: X.Org Video Driver, version 10.0 [ 34.724] (II) LoadModule: "radeon" [ 34.725] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so [ 34.923] (II) Module radeon: vendor="X.Org Foundation" [ 34.923] compiled for 1.10.3, module version = 6.14.2 [ 34.923] Module class: X.Org Video Driver [ 34.923] ABI class: X.Org Video Driver, version 10.0 [ 34.945] (II) LoadModule: "vesa" [ 34.945] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so [ 34.988] (II) Module vesa: vendor="X.Org Foundation" [ 34.988] compiled for 1.10.3, module version = 2.3.0 [ 34.988] Module class: X.Org Video Driver [ 34.988] ABI class: X.Org Video Driver, version 10.0 [ 34.988] (II) LoadModule: "fbdev" [ 34.988] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so [ 35.020] (II) Module fbdev: vendor="X.Org Foundation" [ 35.020] compiled for 1.10.3, module version = 0.4.2 [ 35.020] ABI class: X.Org Video Driver, version 10.0 [ 35.020] (II) RADEON: Driver for ATI Radeon chipsets: <snip> [ 35.023] (II) VESA: driver for VESA chipsets: vesa [ 35.023] (II) FBDEV: driver for framebuffer: fbdev [ 35.023] (++) using VT number 7 [ 35.033] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so [ 35.033] (II) [KMS] Kernel modesetting enabled. [ 35.033] (WW) Falling back to old probe method for vesa [ 35.034] (WW) Falling back to old probe method for fbdev [ 35.034] (II) Loading sub module "fbdevhw" [ 35.034] (II) LoadModule: "fbdevhw" [ 35.034] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so [ 35.185] (II) Module fbdevhw: vendor="X.Org Foundation" [ 35.185] compiled for 1.10.4, module version = 0.0.2 [ 35.185] ABI class: X.Org Video Driver, version 10.0 [ 35.288] (II) RADEON(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 35.288] (==) RADEON(0): Depth 24, (--) framebuffer bpp 32 [ 35.288] (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps) [ 35.288] (==) RADEON(0): Default visual is TrueColor [ 35.288] (==) RADEON(0): RGB weight 888 [ 35.288] (II) RADEON(0): Using 8 bits per RGB (8 bit DAC) [ 35.288] (--) RADEON(0): Chipset: "ATI Mobility Radeon HD 4200" (ChipID = 0x9712) [ 35.288] (II) RADEON(0): PCI card detected [ 35.288] drmOpenDevice: node name is /dev/dri/card0 [ 35.288] drmOpenDevice: open result is 9, (OK) [ 35.288] drmOpenByBusid: Searching for BusID pci:0000:01:05.0 [ 35.288] drmOpenDevice: node name is /dev/dri/card0 [ 35.288] drmOpenDevice: open result is 9, (OK) [ 35.288] drmOpenByBusid: drmOpenMinor returns 9 [ 35.288] drmOpenByBusid: drmGetBusid reports pci:0000:01:05.0 [ 35.288] (II) Loading sub module "exa" [ 35.288] (II) LoadModule: "exa" [ 35.288] (II) Loading /usr/lib/xorg/modules/libexa.so [ 35.335] (II) Module exa: vendor="X.Org Foundation" [ 35.335] compiled for 1.10.4, module version = 2.5.0 [ 35.335] ABI class: X.Org Video Driver, version 10.0 [ 35.335] (II) RADEON(0): KMS Color Tiling: disabled [ 35.335] (II) RADEON(0): KMS Pageflipping: enabled [ 35.335] (II) RADEON(0): SwapBuffers wait for vsync: enabled [ 35.360] (II) RADEON(0): Output VGA-0 has no monitor section [ 35.360] (II) RADEON(0): Output LVDS has no monitor section [ 35.364] (II) RADEON(0): Output HDMI-0 has no monitor section [ 35.388] (II) RADEON(0): EDID for output VGA-0 [ 35.388] (II) RADEON(0): EDID for output LVDS [ 35.388] (II) RADEON(0): Manufacturer: LGD Model: 2ac Serial#: 0 [ 35.388] (II) RADEON(0): Year: 2010 Week: 0 [ 35.388] (II) RADEON(0): EDID Version: 1.3 [ 35.388] (II) RADEON(0): Digital Display Input [ 35.388] (II) RADEON(0): Max Image Size [cm]: horiz.: 34 vert.: 19 [ 35.388] (II) RADEON(0): Gamma: 2.20 [ 35.388] (II) RADEON(0): No DPMS capabilities specified [ 35.388] (II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 [ 35.388] (II) RADEON(0): First detailed timing is preferred mode [ 35.388] (II) RADEON(0): redX: 0.616 redY: 0.371 greenX: 0.355 greenY: 0.606 [ 35.388] (II) RADEON(0): blueX: 0.152 blueY: 0.100 whiteX: 0.313 whiteY: 0.329 [ 35.388] (II) RADEON(0): Manufacturer's mask: 0 [ 35.388] (II) RADEON(0): Supported detailed timing: [ 35.388] (II) RADEON(0): clock: 69.3 MHz Image Size: 344 x 194 mm [ 35.388] (II) RADEON(0): h_active: 1366 h_sync: 1398 h_sync_end 1430 h_blank_end 1486 h_border: 0 [ 35.388] (II) RADEON(0): v_active: 768 v_sync: 770 v_sync_end 774 v_blanking: 782 v_border: 0 [ 35.388] (II) RADEON(0): LG Display [ 35.388] (II) RADEON(0): LP156WH2-TLQB [ 35.388] (II) RADEON(0): EDID (in hex): [ 35.388] (II) RADEON(0): 00ffffffffffff0030e4ac0200000000 [ 35.388] (II) RADEON(0): 00140103802213780ac1259d5f5b9b27 [ 35.388] (II) RADEON(0): 19505400000001010101010101010101 [ 35.388] (II) RADEON(0): 010101010101121b567850000e302020 [ 35.388] (II) RADEON(0): 240058c2100000190000000000000000 [ 35.388] (II) RADEON(0): 00000000000000000000000000fe004c [ 35.388] (II) RADEON(0): 4720446973706c61790a2020000000fe [ 35.388] (II) RADEON(0): 004c503135365748322d544c514200c1 [ 35.388] (II) RADEON(0): Printing probed modes for output LVDS [ 35.388] (II) RADEON(0): Modeline "1366x768"x59.6 69.30 1366 1398 1430 1486 768 770 774 782 -hsync -vsync (46.6 kHz) [ 35.388] (II) RADEON(0): Modeline "1280x720"x59.9 74.50 1280 1344 1472 1664 720 723 728 748 -hsync +vsync (44.8 kHz) [ 35.388] (II) RADEON(0): Modeline "1152x768"x59.8 71.75 1152 1216 1328 1504 768 771 781 798 -hsync +vsync (47.7 kHz) [ 35.388] (II) RADEON(0): Modeline "1024x768"x59.9 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync (47.8 kHz) [ 35.388] (II) RADEON(0): Modeline "800x600"x59.9 38.25 800 832 912 1024 600 603 607 624 -hsync +vsync (37.4 kHz) [ 35.388] (II) RADEON(0): Modeline "848x480"x59.7 31.50 848 872 952 1056 480 483 493 500 -hsync +vsync (29.8 kHz) [ 35.388] (II) RADEON(0): Modeline "720x480"x59.7 26.75 720 744 808 896 480 483 493 500 -hsync +vsync (29.9 kHz) [ 35.388] (II) RADEON(0): Modeline "640x480"x59.4 23.75 640 664 720 800 480 483 487 500 -hsync +vsync (29.7 kHz) [ 35.392] (II) RADEON(0): EDID for output HDMI-0 [ 35.392] (II) RADEON(0): Output VGA-0 disconnected [ 35.392] (II) RADEON(0): Output LVDS connected [ 35.392] (II) RADEON(0): Output HDMI-0 disconnected [ 35.392] (II) RADEON(0): Using exact sizes for initial modes [ 35.392] (II) RADEON(0): Output LVDS using initial mode 1366x768 [ 35.392] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 35.392] (II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:10000000 visible:fba0000 [ 35.392] (II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM [ 35.392] (==) RADEON(0): DPI set to (96, 96) [ 35.392] (II) Loading sub module "fb" [ 35.392] (II) LoadModule: "fb" [ 35.392] (II) Loading /usr/lib/xorg/modules/libfb.so [ 35.492] (II) Module fb: vendor="X.Org Foundation" [ 35.492] compiled for 1.10.4, module version = 1.0.0 [ 35.492] ABI class: X.Org ANSI C Emulation, version 0.4 [ 35.492] (II) Loading sub module "ramdac" [ 35.492] (II) LoadModule: "ramdac" [ 35.492] (II) Module "ramdac" already built-in [ 35.492] (II) UnloadModule: "vesa" [ 35.492] (II) Unloading vesa [ 35.492] (II) UnloadModule: "fbdev" [ 35.492] (II) Unloading fbdev [ 35.492] (II) UnloadModule: "fbdevhw" [ 35.492] (II) Unloading fbdevhw [ 35.492] (--) Depth 24 pixmap format is 32 bpp [ 35.492] (II) RADEON(0): [DRI2] Setup complete [ 35.492] (II) RADEON(0): [DRI2] DRI driver: r600 [ 35.492] (II) RADEON(0): Front buffer size: 4224K [ 35.492] (II) RADEON(0): VRAM usage limit set to 228096K [ 35.615] (==) RADEON(0): Backing store disabled [ 35.615] (II) RADEON(0): Direct rendering enabled [ 35.658] (II) RADEON(0): Setting EXA maxPitchBytes [ 35.658] (II) EXA(0): Driver allocated offscreen pixmaps [ 35.658] (II) EXA(0): Driver registered support for the following operations: [ 35.658] (II) Solid [ 35.658] (II) Copy [ 35.658] (II) Composite (RENDER acceleration) [ 35.658] (II) UploadToScreen [ 35.658] (II) DownloadFromScreen [ 35.687] (II) RADEON(0): Acceleration enabled [ 35.687] (==) RADEON(0): DPMS enabled [ 35.687] (==) RADEON(0): Silken mouse enabled [ 35.721] (II) RADEON(0): Set up textured video [ 35.721] (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 35.721] (--) RandR disabled [ 35.721] (II) Initializing built-in extension Generic Event Extension [ 35.721] (II) Initializing built-in extension SHAPE [ 35.721] (II) Initializing built-in extension MIT-SHM [ 35.721] (II) Initializing built-in extension XInputExtension [ 35.721] (II) Initializing built-in extension XTEST [ 35.721] (II) Initializing built-in extension BIG-REQUESTS [ 35.721] (II) Initializing built-in extension SYNC [ 35.721] (II) Initializing built-in extension XKEYBOARD [ 35.721] (II) Initializing built-in extension XC-MISC [ 35.721] (II) Initializing built-in extension SECURITY [ 35.721] (II) Initializing built-in extension XINERAMA [ 35.721] (II) Initializing built-in extension XFIXES [ 35.721] (II) Initializing built-in extension RENDER [ 35.721] (II) Initializing built-in extension RANDR [ 35.721] (II) Initializing built-in extension COMPOSITE [ 35.721] (II) Initializing built-in extension DAMAGE [ 35.721] (II) SELinux: Disabled on system [ 35.982] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer [ 35.982] (II) AIGLX: enabled GLX_INTEL_swap_event [ 35.982] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control [ 35.982] (II) AIGLX: enabled GLX_SGI_make_current_read [ 35.982] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects [ 35.982] (II) AIGLX: Loaded and initialized /usr/lib/dri/r600_dri.so [ 35.982] (II) GLX: Initialized DRI2 GL provider for screen 0 [ 35.999] (II) RADEON(0): Setting screen physical size to 361 x 203 [ 43.896] (II) RADEON(0): EDID vendor "LGD", prod id 684 [ 43.896] (II) RADEON(0): Printing DDC gathered Modelines: [ 43.896] (II) RADEON(0): Modeline "1366x768"x0.0 69.30 1366 1398 1430 1486 768 770 774 782 -hsync -vsync (46.6 kHz) [ 43.924] (II) RADEON(0): EDID vendor "LGD", prod id 684 [ 43.924] (II) RADEON(0): Printing DDC gathered Modelines: [ 43.924] (II) RADEON(0): Modeline "1366x768"x0.0 69.30 1366 1398 1430 1486 768 770 774 782 -hsync -vsync (46.6 kHz) [ 43.988] (II) RADEON(0): EDID vendor "LGD", prod id 684 [ 43.988] (II) RADEON(0): Printing DDC gathered Modelines: [ 43.988] (II) RADEON(0): Modeline "1366x768"x0.0 69.30 1366 1398 1430 1486 768 770 774 782 -hsync -vsync (46.6 kHz) [ 67.375] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event1) [ 67.376] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall" [ 67.376] (II) LoadModule: "evdev" [ 67.376] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so [ 67.392] (II) Module evdev: vendor="X.Org Foundation" [ 67.392] compiled for 1.10.3, module version = 2.6.0 [ 67.392] Module class: X.Org XInput Driver [ 67.392] ABI class: X.Org XInput driver, version 12.2 [ 67.392] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse' [ 67.392] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so [ 67.392] (**) Logitech USB Optical Mouse: always reports core events [ 67.392] (**) Logitech USB Optical Mouse: Device: "/dev/input/event1" [ 67.392] (--) Logitech USB Optical Mouse: Found 12 mouse buttons [ 67.392] (--) Logitech USB Optical Mouse: Found scroll wheel(s) [ 67.392] (--) Logitech USB Optical Mouse: Found relative axes [ 67.392] (--) Logitech USB Optical Mouse: Found x and y relative axes [ 67.392] (II) Logitech USB Optical Mouse: Configuring as mouse [ 67.392] (II) Logitech USB Optical Mouse: Adding scrollwheel support [ 67.392] (**) Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5 [ 67.392] (**) Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 [ 67.392] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:13.0/usb5/5-1/5-1:1.0/input/input14/event1" [ 67.392] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE) [ 67.392] (II) Logitech USB Optical Mouse: initialized for relative axes. [ 67.392] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1 [ 67.392] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0 [ 67.392] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000 [ 67.392] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4 [ 67.392] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0) [ 67.392] (II) No input driver/identifier specified (ignoring) [ 78.692] (II) Logitech USB Optical Mouse: Close [ 78.692] (II) UnloadModule: "evdev" [ 78.692] (II) Unloading evdev

  Read the article

• 12.04 Unity 3D Not working where as Unity 2D works fine

  - by Stephen Martin

  I updated from 11.10 to 12.04 using the distribution upgrade, after that I couldn't log into using the Unity 3D desktop after logging in I would either never get unity's launcher or I would get the launcher and once I tried to do anything the windows lost their decoration and nothing would respond. If I use Unity 2D it works fine and in fact I'm using it to type this. I managed to get some info out of dmesg that looks like it's the route of whats happening. dmesg: [ 109.160165] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [ 109.160180] [drm] capturing error event; look for more information in /debug/dri/0/i915_error_state [ 109.167587] [drm:i915_wait_request] *ERROR* i915_wait_request returns -11 (awaiting 1226 at 1218, next 1227) [ 109.672273] [drm:i915_reset] *ERROR* Failed to reset chip. output of lspci | grep vga 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) output of /usr/lib/nux/unity_support_test -p IN 12.04 OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 0x300) OpenGL version string: 2.1 Mesa 8.0.2 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no The same command in 11.10: stephenm@mcr-ubu1:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Mobile Intel® GM45 Express Chipset OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes stephenm@mcr-ubu1:~$ output of /var/log/Xorg.0.log [ 11.971] (II) intel(0): EDID vendor "LPL", prod id 307 [ 11.971] (II) intel(0): Printing DDC gathered Modelines: [ 11.971] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 12.770] (II) intel(0): Allocated new frame buffer 2176x800 stride 8704, tiled [ 15.087] (II) intel(0): EDID vendor "LPL", prod id 307 [ 15.087] (II) intel(0): Printing DDC gathered Modelines: [ 15.087] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 33.310] (II) XKB: reuse xkmfile /var/lib/xkb/server-93A39E9580D1D5B855D779F4595485C2CC66E0CF.xkm [ 34.900] (WW) intel(0): flip queue failed: Invalid argument [ 34.900] (WW) intel(0): Page flip failed: Invalid argument [ 34.900] (WW) intel(0): flip queue failed: Invalid argument [ 34.900] (WW) intel(0): Page flip failed: Invalid argument [ 34.913] (WW) intel(0): flip queue failed: Invalid argument [ 34.913] (WW) intel(0): Page flip failed: Invalid argument [ 34.913] (WW) intel(0): flip queue failed: Invalid argument [ 34.913] (WW) intel(0): Page flip failed: Invalid argument [ 34.926] (WW) intel(0): flip queue failed: Invalid argument [ 34.926] (WW) intel(0): Page flip failed: Invalid argument [ 34.926] (WW) intel(0): flip queue failed: Invalid argument [ 34.926] (WW) intel(0): Page flip failed: Invalid argument [ 35.501] (WW) intel(0): flip queue failed: Invalid argument [ 35.501] (WW) intel(0): Page flip failed: Invalid argument [ 35.501] (WW) intel(0): flip queue failed: Invalid argument [ 35.501] (WW) intel(0): Page flip failed: Invalid argument [ 41.519] [mi] Increasing EQ size to 512 to prevent dropped events. [ 42.079] (EE) intel(0): Detected a hung GPU, disabling acceleration. [ 42.079] (EE) intel(0): When reporting this, please include i915_error_state from debugfs and the full dmesg. [ 42.598] (II) intel(0): EDID vendor "LPL", prod id 307 [ 42.598] (II) intel(0): Printing DDC gathered Modelines: [ 42.598] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 51.052] (II) AIGLX: Suspending AIGLX clients for VT switch I know im using the beta version so I'm not expecting it to work but does any one know what the problem may be or even why they Unity compatibility test is describing my video card as vmware when its an intel i915 and Ubuntu is running on the metal not virtualised. Unity 3D worked fine in 11.10

  Read the article

• Unity 3D Not working where as Unity 2D works fine [closed]

  - by Stephen Martin

  I updated from 11.10 to 12.04 using the distribution upgrade, after that I couldn't log into using the Unity 3D desktop after logging in I would either never get unity's launcher or I would get the launcher and once I tried to do anything the windows lost their decoration and nothing would respond. If I use Unity 2D it works fine and in fact I'm using it to type this. I managed to get some info out of dmesg that looks like it's the route of whats happening. dmesg: [ 109.160165] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [ 109.160180] [drm] capturing error event; look for more information in /debug/dri/0/i915_error_state [ 109.167587] [drm:i915_wait_request] *ERROR* i915_wait_request returns -11 (awaiting 1226 at 1218, next 1227) [ 109.672273] [drm:i915_reset] *ERROR* Failed to reset chip. output of lspci | grep vga 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) output of /usr/lib/nux/unity_support_test -p IN 12.04 OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 0x300) OpenGL version string: 2.1 Mesa 8.0.2 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no The same command in 11.10: stephenm@mcr-ubu1:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Mobile Intel® GM45 Express Chipset OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes stephenm@mcr-ubu1:~$ output of /var/log/Xorg.0.log [ 11.971] (II) intel(0): EDID vendor "LPL", prod id 307 [ 11.971] (II) intel(0): Printing DDC gathered Modelines: [ 11.971] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 12.770] (II) intel(0): Allocated new frame buffer 2176x800 stride 8704, tiled [ 15.087] (II) intel(0): EDID vendor "LPL", prod id 307 [ 15.087] (II) intel(0): Printing DDC gathered Modelines: [ 15.087] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 33.310] (II) XKB: reuse xkmfile /var/lib/xkb/server-93A39E9580D1D5B855D779F4595485C2CC66E0CF.xkm [ 34.900] (WW) intel(0): flip queue failed: Invalid argument [ 34.900] (WW) intel(0): Page flip failed: Invalid argument [ 34.900] (WW) intel(0): flip queue failed: Invalid argument [ 34.900] (WW) intel(0): Page flip failed: Invalid argument [ 34.913] (WW) intel(0): flip queue failed: Invalid argument [ 34.913] (WW) intel(0): Page flip failed: Invalid argument [ 34.913] (WW) intel(0): flip queue failed: Invalid argument [ 34.913] (WW) intel(0): Page flip failed: Invalid argument [ 34.926] (WW) intel(0): flip queue failed: Invalid argument [ 34.926] (WW) intel(0): Page flip failed: Invalid argument [ 34.926] (WW) intel(0): flip queue failed: Invalid argument [ 34.926] (WW) intel(0): Page flip failed: Invalid argument [ 35.501] (WW) intel(0): flip queue failed: Invalid argument [ 35.501] (WW) intel(0): Page flip failed: Invalid argument [ 35.501] (WW) intel(0): flip queue failed: Invalid argument [ 35.501] (WW) intel(0): Page flip failed: Invalid argument [ 41.519] [mi] Increasing EQ size to 512 to prevent dropped events. [ 42.079] (EE) intel(0): Detected a hung GPU, disabling acceleration. [ 42.079] (EE) intel(0): When reporting this, please include i915_error_state from debugfs and the full dmesg. [ 42.598] (II) intel(0): EDID vendor "LPL", prod id 307 [ 42.598] (II) intel(0): Printing DDC gathered Modelines: [ 42.598] (II) intel(0): Modeline "1280x800"x0.0 69.30 1280 1328 1360 1405 800 803 809 822 -hsync -vsync (49.3 kHz) [ 51.052] (II) AIGLX: Suspending AIGLX clients for VT switch I know im using the beta version so I'm not expecting it to work but does any one know what the problem may be or even why they Unity compatibility test is describing my video card as vmware when its an intel i915 and Ubuntu is running on the metal not virtualised. Unity 3D worked fine in 11.10

  Read the article

• Intel Dual Band Wireless-AC 7260 keeps dropping wifi

  - by Rick T

  My wifi Intel Dual Band Wireless-AC 7260 keeps dropping wificonnection drops and the network to which I was connected disappears from the list of available networks in network manager. The only way to fix it is to disable wifi and re-enable it How can I fix this. I'm using ubuntu 14.04 64bit. It mostly drops connections on the 5ghz network. My other devices don't drop connections over wifi. see logs and versions rt@simon:~$ uname -a Linux simon 3.13.0-34-generic #60-Ubuntu SMP Wed Aug 13 15:45:27 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux rt@simon:~$ rt@simon:~$ dmesg | grep iwl [ 3.370777] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [ 3.381089] iwlwifi 0000:03:00.0: loaded firmware version 22.24.8.0 op_mode iwlmvm [ 3.414637] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 3.414695] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.414913] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S rt@simon:~$ cat /var/log/syslog | grep -e iwl -e 80211 | tail -n25 Aug 14 08:13:02 simon kernel: [ 3.452780] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:13:02 simon kernel: [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Aug 14 08:13:06 simon NetworkManager[1125]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:03:00.0/ieee80211/phy0/rfkill1) (driver iwlwifi) Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): using nl80211 for WiFi device control Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Aug 14 08:13:06 simon kernel: [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:13:06 simon kernel: [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:14:18 simon kernel: [ 81.230162] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:14:18 simon kernel: [ 81.232330] cfg80211: World regulatory domain updated: Aug 14 08:14:18 simon kernel: [ 81.232332] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:14:18 simon kernel: [ 81.232333] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232334] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232335] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232336] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232337] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:02 simon kernel: [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:02 simon kernel: [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:18 simon kernel: [ 621.223905] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:23:18 simon kernel: [ 621.228945] cfg80211: World regulatory domain updated: Aug 14 08:23:18 simon kernel: [ 621.228950] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:23:18 simon kernel: [ 621.228954] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228956] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228959] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228961] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228963] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

  Read the article

• Ubuntu 12.04 / 12.10 Randomly Freezing - nVidia?

  - by Alix Axel

  My Ubuntu install frequently freezes, sometimes showing a black screen (not very common anymore - in my latest installs), some other times the mouse and keyboard just fail to move and respond (not even Ctrl + Alt + F1 works) and some other times I'm able to move the mouse with a huge delay (2-5 seconds) but I'm not able to do/click anything. I have a pretty strong feeling that this problem is related to my graphic card drivers because: after hard reset, I usually get error reports about X.org / jockey it's common for artifacts to appear during loading / shutdown / whenever, for instance: pattern filled with £ during log off ugly-colored squared pattern during boot windows that are partially moved (i.e.: only the top half) Firefox renderings that leave the bottom ~30% of the page black These artifacts appear right before the system freezes. I've installed Ubuntu 12.04 LTS and after several failed attempts to get my dual monitor setup to work properly I tried installing the new 12.10 version, hoping that this new version would have this problem solved... Unfortunatly, that was not the case, so I reverted to Ubuntu 12.04. I've tried all the drivers in the Additional Drivers application (even the experimental ones), I've also tried the nvidia-current package from the PPA repository ubuntu-x-swat/x-updates as well as the nouveau OSS driver. Nothing (except no driver at all with a 640*480 resolution) at all seems stable. Here is the info of my graphic card: alix@alix-E500:~$ lspci | grep VGA 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [GeForce 8400M G] (rev a1) alix@alix-E500:~$ sudo lshw -C video [sudo] password for alix: *-display description: VGA compatible controller product: G86 [GeForce 8400M G] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:fd000000-fdffffff memory:d0000000-dfffffff memory:fa000000-fbffffff ioport:cc00(size=128) memory:fe0e0000-fe0fffff Right now, I don't even have my 22" monitor connected as I can't even get my laptop display to work properly and without freezes. I've searched, read and tried all that I could (over several fresh reinstalls) to fix the problem, but so far, no solution has proven definitive. I'm sorry I can't precise which symptom maps to each driver but I've been trying to solve this one on my own without logging what I'm doing, perhaps someone here will be able to point me to a certain-fix solution, if not I'll keep updating this question as I go along. Please let me know if any more info is needed to pinpoint the exact problem. Trying out NVIDIA accelerated graphics driver (version 173). The scrolling, minimizing / maximizing windows takes between 2 and 5 seconds to finalize. Context menus also pop up very slowly and the typing seems delayed by ~1 second. No critical issues so far. Firefox rendering of the Save Edits button is consistently messed up (random black lines in the top). Trying out NVIDIA accelerated graphics driver (version current) [Recommended]. All the delays mentioned above and the buggy rendering of the Save Edits button are gone, but I'm noticing that the whole screen flashes black for a couple of microseconds and while I was writing this test for the first time, the bottom 30% of the screen went black and I couldn't do anything (not even Ctrl + Alt + F1 would work). Had to force a hard reset. Also, the system hanged a little for a couple of seconds with the fade out of the "Restart" menu. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-304). Same symptoms as before, it crashed once while I was trying to install Chromium and again after a hard reset when I was trying to remove the driver. The bottom of the screen did not went black and I could move my mouse both times. Ctrl + Alt + F1 didn't work. The ugly-colored pattern also showed up during the second boot. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-307). The system crashed as soon as I clicked something. Had to do a fresh re-install. Trying out Nouveau: Accelerated Open Source driver for nVidia cards. Artifacts still show up during boot but other than that this one seems stable. As soon as I connected my second monitor, the responsiveness dropped a lot, animations and video are somewhat slow. I'm gonna try this solution http://askubuntu.com/a/98871/9018 later on.

  Read the article

• Install lubuntu 12.04 on an old Dell c600 : Video issues

  - by maniat1k

  I am trying to install lubuntu on an old laptop. I use the 386 alternate instalation of it, because it has only 256mb ... All when ok so when I start up the lubuntu the screen splits between 1024x768 and 800x600... its very horrible to use =). Ok I do this: lspci and found an ATI Rage mobility M3. 01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02) So I tryied the old xorg way to edit the missing resolution, but it does not work:... Section "Screen" Identifier "Default Screen" Device "ATI Technologies, Inc. Rage Mobility M3 (AGP)" Monitor "Generic Monitor" DefaultDepth 24 SubSection "Display" Depth 1 Modes "1024x768" EndSubSection SubSection "Display" Depth 4 Modes "1024x768" EndSubSection SubSection "Display" Depth 8 Modes "1024x768" EndSubSection SubSection "Display" Depth 15 Modes "1024x768" EndSubSection SubSection "Display" Depth 16 Modes "1024x768" EndSubSection SubSection "Display" Depth 24 Modes "1024x768" EndSubSection EndSection on an brand new xorg.conf... Do an init 6 to see if X take the changes, but nothing habbened: also tryed to do pkg-reconfigure -changedir /etc/X11 (where I created the new xorg.conf) and nothing.. removed the X conf from /tmp.. also do sudo apt-get update / upgrade... and no luck... UPDATE Updated to 12.04. This an edited xorg fr old dells like mine: # xorg.conf (X.Org X Window System server configuration file) # # This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database. # # Edit this file with caution, and see the xorg.conf manual page. # (Type "man xorg.conf" at the shell prompt.) # # This file is automatically updated on xserver-xorg package upgrades *only* # if it has not been modified since the last upgrade of the xserver-xorg # package. # # If you have edited this file but would like it to be automatically updated # again, run the following command: # sudo dpkg-reconfigure -phigh xserver-xorg # xorg.conf for dell latitude c600 by A. Howlett and others Section "ServerLayout" Identifier "Default Server Layout" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" InputDevice "Generic Mouse" "AlwaysCore" EndSection Section "Files" RgbPath "/usr/X11R6/lib/X11/rgb" FontPath "/usr/share/fonts/local" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/75dpi:unscaled" FontPath "/usr/share/fonts/100dpi:unscaled" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/CID" FontPath "/usr/share/fonts/Speedo" FontPath "/usr/share/fonts/cyrillic" FontPath "/usr/share/fonts/artwiz-aleczapka" FontPath "/usr/share/fonts/TTF" FontPath "/usr/share/fonts/util" FontPath "/usr/local/share/fonts" FontPath "/usr/share/fonts" FontPath "/usr/share/fonts" FontPath "/usr/share/fonts/aquafont" FontPath "/usr/share/fonts/artwiz" FontPath "/usr/share/fonts/artwiz-aleczapka-en" FontPath "/usr/share/fonts/corefonts" FontPath "/usr/share/fonts/freefont" EndSection Section "Module" Load "GLcore" Load "dbe" Load "dri" Load "extmod" Load "glx" Load "pex5" Load "record" Load "xie" Load "v4l" Load "freetype" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "keyboard" Option "XkbModel" "pc104" Option "XkbLayout" "us" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "CorePointer" Option "Device" "/dev/psaux" Option "Protocol" "PS/2" Option "Emulate3Buttons" "true" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" Identifier "Generic Mouse" Driver "mouse" Option "SendCoreEvents" "true" Option "Device" "/dev/input/mice" Option "Protocol" "ImPS/2" Option "Emulate3Buttons" "true" Option "ZAxisMapping" "4 5" EndSection Section "Monitor" Identifier "laptop LCD" VendorName "Dell" ModelName "Latitude C600" HorizSync 31.5-48.5 VertRefresh 40-70 EndSection Section "Device" Identifier "Video0" Driver "r128" VideoRam 8192 Option "EnablePageFlip" "true" Option "AGPFastWrite" "true" Option "AGPMode" "2" BusID "PCI:01:00:0" Screen 0 Option "Display" "FP" Option "MonitorLayout" "CRT, LFP" EndSection Section "Screen" Identifier "Screen0" Device "Video0" Monitor "laptop LCD" DefaultDepth 16 Subsection "Display" Depth 32 Modes "1280x1024" "1152x864" "1024x768" "800x600" "640x480" EndSubSection Subsection "Display" Depth 24 Modes "1280x1024" "1152x864" "1024x768" "800x600" "640x480" EndSubSection Subsection "Display" Depth 16 Modes "1280x1024" "1152x864" "1024x768" "800x600" "640x480" EndSubSection Subsection "Display" Depth 8 Modes "1280x1024" "1152x864" "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Mode 0666 EndSection

  Read the article

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• How do I configure WakeOnUSB properly?

  - by wishi

  How do I configure Wake-On-USB properly on a 10.04 or 10.10 Ubuntu (2.6.36 and higher if needed)? (Wake-on-USB is when the computer is asleep and for example a USB Keyboard event wakes up the machine!) The notebook is an Acer Aspire Timeline X 1830T. I don't know in which way the Linux Kernel supports the controllers. There are different ways to approach this, for example /proc/acpi/wakeup... or UDEV... or something with HAL? /proc/acpi/wakeup shows every device in S4, but I need S3. Device S-state Status Sysfs node P0P2 S4 *disabled PEGP S4 *disabled P0P1 S0 *disabled pci:0000:00:1e.0 EHC1 S4 *disabled pci:0000:00:1d.0 USB1 S4 *enabled USB2 S4 *disabled USB3 S4 *disabled USB4 S4 *disabled EHC2 S4 *disabled pci:0000:00:1a.0 USB5 S4 *disabled USB6 S4 *disabled USB7 S4 *disabled HDEF S0 *disabled pci:0000:00:1b.0 RP01 S5 *disabled pci:0000:00:1c.0 PXSX S5 *disabled pci:0000:01:00.0 RP02 S0 *disabled pci:0000:00:1c.1 PXSX S5 *disabled pci:0000:02:00.0 RP03 S0 *disabled PXSX S5 *disabled RP04 S0 *disabled PXSX S5 *disabled RP05 S0 *disabled PXSX S5 *disabled RP07 S0 *disabled PXSX S5 *disabled RP08 S0 *disabled PXSX S5 *disabled GLAN S0 *disabled PEG3 S4 *disabled PEG5 S4 *disabled PEG6 S4 *disabled SLPB S3 *enabled S4, which is Suspend-To-Disk afaik... doesn't seem to work either if I echo USB1 into the wakeup table. It just sets an S4 flag. can I get the USB ports in S3? I want to make the machine wakeup from Suspend-To-Ram (S3, ACPI standard) in case a key on my external keyboard is pressed. It only wakes up if a key on the internal Laptop keyboard is pressed... from Suspend To Ram. It seems if I plug in a USB mouse, that the USB port isn't even powered. I have no BIOS option to change this. Further specific information regarding the device: usb-devices T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 13 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=04d9 ProdID=1603 Rev=03.10 S: Manufacturer= S: Product=USB Keyboard C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid root@underwater-laptop:/# lsusb [...] Bus 001 Device 013: ID 04d9:1603 Holtek Semiconductor, Inc. Bus 001 Device 004: ID 0bda:0138 Realtek Semiconductor Corp. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub [...] If this doesn't work I have to properly explain why :( - but I think it is very hard to research this kernel internal. Any hints for good information here? I hope it's possible... I'm just looking for any solution. edit: this, waking up on USB, works on Windows! Thanks a lot, Marius

  Read the article

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• Randomely loosing wireless connexion with Cubuntu 12.04

  - by statquant

  I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

  Read the article

• Wireless connection works but the internet is too slow to use in Ubuntu 11.04

  - by Garrin

  The internet is so slow as to be unusable. And I'm not being picky. Even after minutes I can't get my Google home page to load. I tried installing a package through apt-get and was getting rates between 0 and a few hundred bytes/s. That's bytes, not kilobytes! Mostly 0 however (no exaggeration, it spends large amounts of time stalled). And I would go to a speed test web site of some kind but I can't since nothing will load. Briefly put, the laptop I am using was connected to two wireless networks while using Ubuntu 11.04 without any issues before this. It was also connected to a wired network without any issues. It dual boats Windows 7 which has never had any issues, not even with the current wireless network. Just to be clear, on the current wi-fi network, Windows 7 encounters no issues (speedtest.net puts the network speed at 1mb/s) but my network connection in Ubuntu 11.04 is so slow as to literally be unusable. I am unfamiliar with the router except for the fact that it boasts a Rogers logo (that's a large ISP/cable provider in Canada for those not familiar with the land of igloos and polar bears). I am far from the router and some desktop widget I use tells me the signal strength is at 58% (it seems fairly reliable and this would appear to match up with the filled bars in the network icon). I should also mention I'm just renting a room in this house so I'm not the network administrator and while I can access the 192.168.0.1 router page, the password wasn't set to 'password' so it's not much use to me. Here are a bunch of commands I ran which don't tell me a whole lot but I thought might be more instructive to the wise around here: lspci (just showing my network card): 05:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) This one is self explanatory. PING www.googele.com (216.65.41.185) 56(84) bytes of data. 64 bytes from nnw.net (216.65.41.185): icmp_req=1 ttl=51 time=267 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=2 ttl=51 time=190 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=3 ttl=51 time=212 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=4 ttl=51 time=207 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=5 ttl=51 time=220 ms --- www.googele.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4003ms rtt min/avg/max/mdev = 190.079/219.699/267.963/26.121 ms ifconfig eth0 Link encap:Ethernet HWaddr 20:6a:8a:02:20:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:960 (960.0 B) TX bytes:960 (960.0 B) wlan0 Link encap:Ethernet HWaddr 20:7c:8f:05:c6:bf inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::227c:8fff:fe05:c6bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:982 errors:0 dropped:0 overruns:0 frame:0 TX packets:658 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:497250 (497.2 KB) TX bytes:95076 (95.0 KB) Thank you

  Read the article

• Ubuntu 12.10 no network and no graphics

  - by khasiKoMasu

  I recently upgraded Ubuntu 12.04 to 12.10 only to find out that it won't connect to any network, neither wired nor wireless and the graphics is messed up too as in a low screen resolution. For 12.04, my system was running perfectly. I don't know why upgrade messed it up so bad. Reinstalling the OS is an issue because I have set up a lot of development environments that I cannot afford to set it up again. Some of the outputs: lspci -nn | grep 0200 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) nm-tool NetworkManager Tool State: disconnected cat /etc/network/interfaces auto lo iface lo inet loopback sudo cat /var/log/syslog | grep etwork | tail -n20 Nov 2 13:50:22 Cobalt NetworkManager[978]: SCPlugin-Ifupdown: (-1240454760) ... get_connections (managed=false): return empty list. Nov 2 13:50:22 Cobalt NetworkManager[978]: Ifupdown: get unmanaged devices count: 0 Nov 2 13:50:22 Cobalt bluetoothd[1016]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> modem-manager is now available Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> monitoring kernel firmware directory '/lib/firmware'. Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiFi enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WWAN enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiMAX enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> Networking is enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt kernel: [ 28.688167] type=1400 audit(1351882222.452:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1046 comm="apparmor_parser" Nov 2 13:50:22 Cobalt bluetoothd[1062]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1118]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1237]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) ps aux | grep -i network root 978 0.0 0.1 23732 4808 ? Ssl 13:50 0:00 NetworkManager sudo modprobe -r forcedeth FATAL: Module forcedeth not found

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• Android SDK Manager and AVD Manager doesn't have the correct information and fails to update on Ubun

  - by Johan Carlsson

  I'm trying to install Android SDK on Ubuntu but fail when I try to use the SDK Manager and AVD Manager to install Android platforms. I've downloaded: android-sdk_r04-linux_86.tgz The I start the SDK Manager and AVD Manager (UI) according to the README file: ./tools/android And I get the following Installed Packages: - Install SDK Tools, revision 4 Available Packages: - https://dl-ssl.google.com/android/repoisotry/repository.xml - This repository requires a more recent version of the Tools. Please update- - Android SDK Tools, revision 4 - Archive for Linux (comment: funny since rev 4 seems to be what's installed this is what seems to be installed) Now doing an update of the Android SDK Tools, revision 4 or everything results in 99% progress and then the application hangs. Here's the console feedback: johanc@johan-desktop:~/android/android-sdk-linux_86$ tools/android Starting Android SDK and AVD Manager No command line parameters provided, launching UI. See 'android --help' for operations from the command line. Error: null In the app I choose to upgate the following package: Package Description Android SDK Tools, revision 4 Archive Description Archive for Linux Size: 15 MiB SHA1: 99380c9330c1c3728c836206947350cc00fa28c2 Site https://dl-ssl.google.com/android/repository/repository.xml The console output reads (and the app hangs at 99%): Exception in thread "Installing Archives" java.lang.AssertionError at com.android.sdkuilib.internal.tasks.ProgressTask.incProgress(ProgressTask.java:97) at com.android.sdkuilib.internal.repository.UpdaterData$2.run(UpdaterData.java:358) at com.android.sdkuilib.internal.tasks.ProgressTask$1.run(ProgressTask.java:135)

  Read the article

• Mercurial fails while commiting/updating/etc. using Mercuriual+TrueCrypt+MAC

  - by lukewar

  While trying to work with Mercurial on project located on TrueCrypt partition I always get en error as follows: ** unknown exception encountered, details follow ** report bug details to http://mercurial.selenic.com/bts/ ** or [email protected] ** Mercurial Distributed SCM (version 1.5.2+20100502) ** Extensions loaded: Traceback (most recent call last): File "/usr/local/bin/hg", line 27, in mercurial.dispatch.run() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 16, in run sys.exit(dispatch(sys.argv[1:])) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 30, in dispatch return _runcatch(u, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 50, in _runcatch return _dispatch(ui, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 470, in _dispatch return runcommand(lui, repo, cmd, fullargs, ui, options, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 340, in runcommand ret = _runcommand(ui, options, cmd, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 521, in _runcommand return checkargs() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 475, in checkargs return cmdfunc() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 469, in d = lambda: util.checksignature(func)(ui, *args, **cmdoptions) File "/Library/Python/2.6/site-packages/mercurial/util.py", line 401, in check return func(*args, **kwargs) File "/Library/Python/2.6/site-packages/mercurial/commands.py", line 3332, in update return hg.update(repo, rev) File "/Library/Python/2.6/site-packages/mercurial/hg.py", line 362, in update stats = _merge.update(repo, node, False, False, None) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 495, in update _checkunknown(wc, p2) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 77, in _checkunknown for f in wctx.unknown(): File "/Library/Python/2.6/site-packages/mercurial/context.py", line 660, in unknown return self._status[4] File "/Library/Python/2.6/site-packages/mercurial/util.py", line 156, in get result = self.func(obj) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 622, in _status return self._repo.status(unknown=True) File "/Library/Python/2.6/site-packages/mercurial/localrepo.py", line 1023, in status if (f not in ctx1 or ctx2.flags(f) != ctx1.flags(f) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 694, in flags flag = findflag(self._parents[0]) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 690, in findflag return ff(path) File "/Library/Python/2.6/site-packages/mercurial/dirstate.py", line 145, in f if 'x' in fallback(x): TypeError: argument of type 'NoneType' is not iterable It is worth mention that Mercurial works perfectly if project is not located on TrueCrypt partition. Configuration: MacOS X 10.6.3 Mercurial Distributed SCM (version 1.5.2+20100502) Python 2.6.5 Have anyone of you generous people able to help me? :)

  Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37  | Next Page >