Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 32/215 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Configuring Wireless Network

    - by Vinod K
    I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

    Read the article

  • I have a wireless Canon P560 and my computer can't find it

    - by ed
    The printer is wireless and I haven't connected it via USB. I set the configurations for the Wi-Fi access point in the printer and it connected to my Wi-Fi. I have AT&T as the service provider and the 2Wire router. When I access the router in the browser I see that the printer is connected but when I run the software to detect the printer the computer can't find it. I have a Mac with Snow Leopard. I tried to detect the printer with another device and it can't find it. Is there a port that needs to be open for wireless printers? Because I tried putting the routers firewall settings for the device to its lowest and the computer still can't find it. Let me know. Thnx.

    Read the article

  • Lenovo tools for windows 7: can't re-enable wireless

    - by pcampbell
    Consider a netbook - Lenovo S10e with Windows 7 and the S10 Lenovo power management tools. Machine has factory BIOS. Fn+F5 is the key combo to toggle the wireless radio on/off. The tool allows the disabling fine; works as expected. The problem is that the re-enable doesn't work, or is confusing on how to re-enable. Previously tried without success: Fn-F5 Fn-Ctrl-F5 Fn-Shift-F5 Fn-Alt-F5 Here's the onscreen display: Question: How can you re-enable the wireless radio using the Function key on a Lenovo netbook?

    Read the article

  • Internet wireless connected with limited access, windows vista

    - by Wawa wiya
    Hello I had some malware in my computer so I did a bit of manual work to remove it including resetting TCP/IP. Now the malware is gone. I can see my home wireless network and I can get connected to it but when connected I get the Internet wireless connected with limited access message. When I go to the IE I cannot browse. When I tried to ping 192.168.1.1 I got an Error Code 1231 Unconnected Network Problem. I have deactivated my Windows firewall as I thought it could be hyperactive security. Still no luck. I have Norton but it is not active, I have also Avast and AVG installed but they are not active. Any ideas?

    Read the article

  • is there a way to prevent network manager from storing the password for a wireless network

    - by tolomea
    Our corporate wireless network uses continuously changing passwords with RSA tokens. So every time we need to connect to the wireless we need to enter a new password off the RSA token. For extra fun using the wrong password a couple of times in a row causes the users account to be locked. Network manager automatically stores and reuses the password, with the net result that it is constant getting my account locked. Is there some way to prevent it from storing my password for that network? Or perhaps someway to get the gnome keyring to not store it?

    Read the article

  • Keeping the wireless connected.

    - by casr
    I’m running OpenBSD on a computer which is connected via wireless to the network. It is a well supported NIC and I’ve had no problems with it from a hardware perspective. Unfortunately my wireless access point occasionally loves to forget it’s settings. I then have to help it remember. However, in this intervening time my OpenBSD box drops the connection and then does not automatically reconnect. I have alleviated my problems by running this simple script in the background: #!/bin/sh while [ 1 ] do ping -c1 192.168.1.254 > /dev/null if [ $? = 1 ] then sh /etc/netstart ral0 > /dev/null fi sleep 30 done [Ping the access point. If there is no response attempt to reconnect.] It seems to me to be a very suboptimal solution. Has anyone else come across a better way?

    Read the article

  • VMware Fusion on MacBook Pro running Vista, not working after installing a wireless card

    - by Shelley
    A tech friend installed VMware on my Mac so I could use my Windows programs as well. It worked great until I inserted my Sierra 881 USB wireless card while in VMware trying to get to the internet while on the road. It worked briefly, then the AT&T Communication manager won't respond when you click on the icon, I can't open Network and Sharing center, I can't sync my palm - shows it can't connect. Looks like it messed up several things, along with not being able to connect to the internet while in windows. This wireless cards works directly from the Mac - but I need internet while in Windows for some work I am doing. How do I uninstall this - when I try - it just gives me an endless reloading circle - not doing anything. I really need to sync my palm and get back to the way it was. I don't know much about VMware at all and I don't have access to my friend right now to get help.

    Read the article

  • What is causing my wireless problems?

    - by user34629
    I have a Dell XPS M1330, since I moved to my new house, the wireless barely works on it, my housemates report no problems, so I guess it's something to do with my laptop. It's eratic in normal mode, sometimes not working for days, usually working on-and-off, forcing me to reload pages a few times before they work, etc. It works perfectly in safe mode, the driver I'm using is the Intel PRO/Wireless 3945ABG Network Connection, version 12.4.4.5, with a date at 26/10/2009, the most recent one I could find, bluetooth is not enabled, and I'm running Vista 32-bit Home Premium, which it shipped with. I also tried disabling IPv6 and resetting the IP stack, both to no avail. Can anybody help me?

    Read the article

  • Remote Desktop connection breaks the wireless connection

    - by Michal Talaga
    When I connect to my Windows 8 Professional machine via Remote Desktop (RDP) I almost always get my WiFi connection broken. The setup: T61P Lenovo Laptop + W8 at home Wireless Router with NAT forwards connections to that machine Windows 7 laptop at work connecting to the home laptop When I connect, very often I get to login and suddenly connection is lost and I cannot reconnect again. When I get home I find my WiFi connection is still connected to the Access Point but does not function. Can't even ping the router. What is strange is that disabling wireless with the hardware switch and enabling it again doesn't help. The only way to make it works again: - Reboot - Disable wifi with hardware switch AND disable the network card in Device Manager, then enable both I did not have this problem on the very same laptop when it was running Windows 7. Any hint how can I find where the problem is?

    Read the article

  • Windows 7 computer apparently connected to working wireless network but can't access router page or internet

    - by Hemmer
    I can consistently connect successfully to both the router and the internet using both my phone and two different computers which strongly suggests that the issue is at the desktop end. Only my Windows 7 desktop machine has stopped getting internet connectivity. It manages to connect to the router's network using the Windows 7 wireless dialog, but can't access either the router configuration page (192.168.1.1) or the internet in general once connected. The strange thing is the wireless network icon in the notification bar shows a full strength signal, sometimes with the yellow warning triangle. The output of ipconfig /all is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-12-17-94-98-90 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.102(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 08 June 2011 10:32:16 Lease Expires . . . . . . . . . . : 08 June 2011 12:32:16 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 NetBIOS over Tcpip. . . . . . . . : Enabled I've tried renewing DCHP settings disabling IPv6 resetting TCP stack uninstalling and reinstalling WLAN card drivers I've not installed anything new or made any changes to my knowledge, this just happened out of the blue. The only possible change is my friend connected his macbook to the network, but that has gone now and shouldn't have any lasting effects? TCP/IPv4 is set to automatically find an IP address. Antivirus is MSE (up to date) and doesn't detect anything unusual. Any ideas where to go next? Any help is greatly appreciated. For reference, the results of ipconfig /all on one of the working computers is: Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11g Network Adapter Physical Address. . . . . . . . . : 00-16-CF-67-E5-97 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 194.168.4.100 194.168.8.100 Lease Obtained. . . . . . . . . . : 08 June 2011 10:26:38 Lease Expires . . . . . . . . . . : 08 June 2011 12:26:38 UPDATE: Still not working, but I've managed to find a temporary workaround by tethering my Android phone, effectively becoming a new wifi adapter. Will be moving to a new flat so will test if it is a network specific thing - maybe the card has got damaged somehow? Also will see if the card is working with Linux soon.

    Read the article

  • New tab in Safari window from Cocoa and Scripting Bridge

    - by Thor Frølich
    I'm trying to create a new tab in a Safari window from Cocoa using Scripting Bridge. My code looks something like this: SafariApplication *safari = [SBApplication applicationWithBundleIdentifier:@"com.apple.Safari"]; if ([[safari windows] count] == 0) { NSLog(@"No window found. Creating a new one."); SafariDocument *newDoc = [[[safari classForScriptingClass:@"document"] alloc] init]; [[safari windows] addObject:newDoc]; [newDoc release]; } else { NSLog(@"Seems we already have a safari window"); SafariTab *newTab = [[[safari classForScriptingClass:@"tab"] alloc] init]; [[[safari windows] objectAtIndex:0] addObject:newTab]; [newTab release]; } The first part if the "if" works, creating a new window. Creating the tab does not. This gets me "-[SafariWindow addObject:]: unrecognized selector sent to instance...", so obviously that's not the way to do it. I can't figure out how windows, documents and tabs relate to each other in Safari. Any help is greatly appreciated. Thanks, Thor

    Read the article

  • Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

    - by gil b.
    Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

    Read the article

  • Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

    - by gil b.
    Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

    Read the article

  • 802.11g -> wired ethernet bridging not working

    - by Malachi
    Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

    Read the article

  • Meaning of Bridge-Check in iptables flowchart

    - by networkIT
    In the famous iptables flow-chart what does bridge-check exactly stands for ? I couldn't find any documentation. The only clue I found was while scanning the MikroTik RouterOS documentation ( RouterOS is build upon a Linux 2.6.16 kernel ), I found this : In-interface Bridge = Checks if the input interface is a port for a bridge or is the bridge. Manual:Packet Flow Comparing both flow-charts brings clues that iptables Bridge-check might equal MikroTik In-Interface Bridge. Is this true ? Else, what might be the meaning of iptables Bridge-Check ?

    Read the article

  • Why do I have inconsistent network issues with my laptop's wireless?

    - by Jason
    I'm having trouble with my laptop Internet connection. It's patchy at best and resets or freezes a lot. The signal strength is also random. I thought it might be a driver issue but now I don't know. Three other computers using the same wireless network run well. I've switched out wireless routers so I don't think it's the router. I thought it might be the laptop's internal wireless card but I just bought an external USB network card and I'm still having problems. Specs Lenovo T-60p Windows 7 Ultimate Edition Patches/drivers are up to date I only use one of the below at a time, disabling the other: Intel PRO/Wireless 3945ABG v. 13.3.0.137 (Internal wireless) Medialink Wireless-N USB 2.0 Adapter (USB wireless) Any ideas on what might be the problem?

    Read the article

  • How do I get a Broadcom Wireless BCM43225 card working?

    - by DanFritz
    During the installation of my Ubuntu 12.10 I could use the wireless connection for extra updates. After the installation I updated Ubuntu and it installed 74 new updates, after that no wireless connection (say what!). So I did try some stuff, I followed the tutorial to load the windows drivers using ndiswrapper (https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper) but I always get that the ndiswrapper module is not loaded (but I did install the extra 3 packages, still doesnt work). ndiswrapper-source ndiswrapper-dkms ndiswrapper-common Please somebody help! Thanks a lot

    Read the article

  • How do I get a TP-LINK WN723N wireless USB adapter working?

    - by Bottie
    I am having trouble using a TP-LINK WN723N wireless USB adapter on my computer which is running Ubuntu 12.04. When I plug the adapter in, the computer automatically picks up a signal from my wireless router but only connects to the internet for a short amount of time before losing the connection. I have searched for additional drivers and have tried running the .exe installation file on the WINE drive with no such luck... Am very new to Ubuntu would love some help! Thanks :-)

    Read the article

  • cisco ePC 3208 router and captive portal

    - by Dejan Milosevic
    Ok, i have cisco ePC 3208 router, and cable internet goes in router via cable and router is emiting wireless. It can work without computer and it is working fine. Now i want to have capiteve portal with home page for my buisness and user logins. Is it possible that i use computer as gateway for captive portal, so when user goes to wireless it will redirected to computer local server for authorization and then passed by if user and pass is good, or i need another router or wifi acess point?

    Read the article

  • using wireless with VMWare workstation 6.5

    - by BdotA
    I am using VMWare workstation 6.5 and have installed WinXP SP2 on it. My main operation system is Win 7. when I am hard-wired, I can use internet inside vmware but when I am wireless, I cannot use internet inside vmware... I did a research and found that the network adapter should be on NAT instead of bridge, I tried that but it did not work either.

    Read the article

  • Switch to switch encryption over a wireless bridge (TrustSec?)

    - by metatheorem
    I am planning to connect an existing Cisco 3750 switch to a 3560C switch over a wireless PTP bridge. The bridge will be WPA2 protected, but I am looking for an additional measure of security between the switches to prevent other wireless access through either switch. They do not support IPSec, only 802.1Q tunnels, and buying additional hardware is not likely an option. I am looking into using TrustSec manual mode between the switches. After some effort reading into TrustSec and MACsec, I am mostly certain this is a good choice over the wireless bridge, keeping in mind it is a shared medium. Two questions: Can I reliably prevent other wireless traffic from accessing the switches using TrustSec? Does anyone know of any better options with the 3000 series switches?

    Read the article

  • Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

    - by BenA
    I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

    Read the article

  • Wireless disconnect randomly with wpa_supplicant reason=2

    - by renenglish
    I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

    Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >