Search Results

Search found 9156 results on 367 pages for 'cloud storage'.

Page 320/367 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• Issue with InnoDB engine while enabling and [ skip-innodb ]

  - by Ahn

  How to enable InnoDB, which was previously disabled with skip-innodb option. Case 1: Disabled the innodb with skip-innodb option and show engines givens as below. Engine | Support ... | InnoDB | NO ...... Case 2: As I want to enable the innodb, I commanded the #skip-innodb option and restarted. But now the show engines even not showing the InnoDB engine in the list. ? Mysql Version : 5.1.57-community-log OS : CentOS release 5.7 (Final) Log: 120622 13:06:36 InnoDB: Initializing buffer pool, size = 8.0M 120622 13:06:36 InnoDB: Completed initialization of buffer pool InnoDB: No valid checkpoint found. InnoDB: If this error appears when you are creating an InnoDB database, InnoDB: the problem may be that during an earlier attempt you managed InnoDB: to create the InnoDB data files, but log file creation failed. InnoDB: If that is the case, please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/error-creating-innodb.html 120622 13:06:36 [ERROR] Plugin 'InnoDB' init function returned error. 120622 13:06:36 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 120622 13:06:36 [Note] Event Scheduler: Loaded 0 events 120622 13:06:36 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.57-community-log' socket: '/data/mysqlsnd/mysql.sock1' port: 3307 MySQL Community Server (GPL)

  Read the article

• Nginx 502 Bad Gateway: It just won't stop

  - by David

  I have the same problem that most people seem to have with Nginx: 502 bad gateway errors. They are intermittent but typically happen more than once per session, which means my users are probably running into it nearly every time they use the app. I've tried adjusting fastcgi_buffers and fastcgi_buffer_size (in both directions) to no avail. I've tried various other things with the configuration file but nothing seems to work. Here's my config (note that I've stripped away most of the things I've tried, since they didn't work and I didn't want to bloat the file with a bunch of un-related directives): server { root /usr/share/nginx/www/; index index.php; # Make site accessible from http://localhost/ server_name localhost; # Pass PHP scripts to PHP-FPM location ~ \.php { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; } # Lock the site location / { auth_basic "Administrator Login"; auth_basic_user_file /usr/share/nginx/.htpasswd; } # Hide the password file location ~ /\. { deny all; } client_max_body_size 8M; } I'm running a small Rackspace cloud server, which should be plenty for handling an app with a small user base...

  Read the article

• What Windows service binds a NIC to the network?

  - by Bigbio2002

  I have a server that takes several minutes for the NIC to bind itself to the network upon startup (it has a statically-configured IP). This causes DNS/WINS/Intersite Messaging to fail to start, since they're dependent on a network connection. While I'm still attempting to find a root cause to this issue (I've done firmware updates, checked for any odd drivers/services, no luck so far), but in the meantime, I want to adjust the load order of services to ensure that the NIC binds first before these services attempt to start. The only question is, which service is it? The server is running Server 2008 R2 and only has one NIC installed. (On a side note, there are two other small but odd problems occuring with the server. The server had the issue described in KB2298620, which I've fixed. The other problem occurs in Windows Server Backup. No events appear in the upper portion of the window, despite the fact that backups are running in the background. Whenever I attempt to modify the backup schedule, it gives me the error "Not enough storage is available to process this command" and appears to fail, when, in fact, it actually succeeds. These may be separate issues, but something tells me that some of these might share a common root cause.)

  Read the article

• central apache log analysis of many hosts

  - by Jason Antman

  We have 30+ apache httpd servers, and are looking to perform analysis on the logs both for historical trending and near "real time" monitoring/alerting. I'm mainly interested in things like error rates (4xx/5xx), response time, overall request rate, etc. but it would also be very useful to pull out more compute-intensive statistics like unique client IPs and user agents per unit of time. I'm leaning towards building this as a centralized collector/server/storage, and am also considering the possibility of storing non-apache logs (i.e. general syslog, firewall logs, etc.) in the same system. Obviously a large part of this will probably have to be custom (at least the connection between pieces and the parsing/analysis we do), but I haven't been able to find much information on people who have done stuff like this, at least at shops smaller than Google/Facebook/etc. who can throw their log data into a hundred-node compute cluster and run Map/Reduce on it. The main things I'm looking for are: - All open source - Some way of collecting logs from apache machines that isn't too resource-intensive, and transports them relatively quickly over the network - Some way of storing them (NoSQL? key-value store?) on the backend, for a given amount of time (and then rolling them up into historical averages) - In the middle of this, a way of graphing in near-real-time (probably also with some statistical analysis on it) and hopefully alerting off of those graphs. Any suggestions/pointers/ideas, to either "products"/projects or descriptions of how other people do this would be greatly helpful. Unfortunately, we're not exactly a new-age-y devops shop, lots of old stuff, homogeneous infrastructure, and strained boxes.

  Read the article

• Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

  - by gts123

  I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• Move files from ftp server to s3

  - by lev

  I would like to set up an ftp server, where users will upload files, and for each file, put it on s3 storage, and delete it from the ftp server. (the server runs on ec2 ubuntu) Here are the stuff I already tried, with no success.. Mount s3 bucket using s3fs. I followed those instructions, but there is a bug in the latest version of s3fs, that prevents it from working. The bug was fixed on the develop branch, but I don't want to use unstable version on my production. Use vsftpd and using s3cmd sync via cron to sync the files periodically. The problem with that approach, is that s3cmd can start running in the middle of a file upload, and start synching the incomplete file. Also s3cmd doesn't give any feedback it the sync fails, so I have no way of knowing if I can delete the files after the sync command finished running. Use pure-ftpd's upload script feature (which allows to run a script after a file is finished uploading), but I noticed that if the file upload was failed in the middle, the script will run anyway, and I have no way of knowing if the upload was successful or not. I've been at it for a few days now, and I'm at a loss here. Any suggestions will be welcomed.

  Read the article

• Array on servers which receive several hundred GB of data a day

  - by Matthew

  This is hopefully a simple question. Right now we are deploying servers which will serve as data warehouses. I know with raid 5 the best practice is 6 disks per raid 5. However, our plan is to use RAID 10 (both for performance and safety). We have a total of 14 disks (16 actually, but two are being used for OS). Keeping in mind that performance is very much an issue, which is better - doing several raid 1's? Do one large raid 10? One large raid 10 had been our original plan, but I want to see if anyone has any opinions I haven't thought of. Please note: This system was designed for using Raid 1+0, so losing half of the raw storage capacity is not an issue. Sorry i hadn't mentioned that initially. The concern is more whether or not we want to use one large Raid 1+0 containing all 14 disks, or several smaller raid 1+0's and then stripe across them using LVM. I know the best practice for higher raid levels is to never use more than 6 disks in an array.

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• KVM and libvirt: How to configure a new disc device to an existing VM?

  - by initall

  I've got an Ubuntu 9.04 server running two VM's. In /etc/libvirt/qemu/machine1.xml two disk devices are defined like this: <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <source file='/vserver/machine1/disk0.qcow2'/> <target dev='hda' bus='ide'/> </disk> <disk type='file' device='disk'> <source file='/vserver/machine1/disk1.qcow2'/> <target dev='hdb' bus='ide'/> </disk> I need more storage space in at least one of the devices and thought about adding a third hdc device by simply adding one with same style as above and re-organising my mount structure (The virtual sizes of the current qcow2 files are unfortunately limited.) My problem is that reloading libvirtd and restarting the VM do not result in a new visible device (checked with fdisk). I'm aware of extending an existing qcow2 file (converting to raw format, cat-ing/adding the new one, using smth. like gparted) - but only as a last resort. Hopefully it's something very simple I'm missing?

  Read the article

• How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

  - by user31575

  Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

  Read the article

• Iptables ignoring a rule in the config file

  - by Overdeath

  I see lot of established connections to my apache server from the ip 188.241.114.22 which eventually causes apache to hang . After I restart the service everything works fine. I tried adding a rule in iptables -A INPUT -s 188.241.114.22 -j DROP but despite that I keep seeing connections from that IP. I'm using centOS and i'm adding the rule like thie: iptables -A INPUT -s 188.241.114.22 -j DROP Right afther that I save it using: service iptables save Here is the output of iptables -L -v ` Chain INPUT (policy ACCEPT 120K packets, 16M bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any c-98-210-5-174.hsd1.ca.comcast.net anywhere 0 0 DROP all -- any any c-98-201-5-174.hsd1.tx.comcast.net anywhere 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any www.dabacus2.com anywhere 0 0 DROP all -- any any 116.255.163.100 anywhere 0 0 DROP all -- any any 94.23.119.11 anywhere 0 0 DROP all -- any any 164.bajanet.mx anywhere 0 0 DROP all -- any any 173-203-71-136.static.cloud-ips.com anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any 74.122.177.12 anywhere 0 0 DROP all -- any any 58.83.227.150 anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 186K packets, 224M bytes) pkts bytes target prot opt in out source destination `

  Read the article

• Hosting multiple websites from home

  - by dean nolan

  I have just been accepted for Microsofts Wevsite Spark program which I mainly got for the tools, Visual Studio, Blend. I also have a few of my own websites, personal and a couple of business ones. I also work freelance and sometimes I would like a place to just put a demo up of a clients project. The websites I currently have are all on differnet hosting provders and domain registrars. The WebsiteSpark comes with Windows Server 2008 and SQL Server 2008. It would be really advantagous of me to have all these in one place but also so I have complete control over the database and the environment. So I am thinking over the next 4-6 months of migrating all this to my own server that I will host from home, or maybe even setup at home and then store in a proper datacentre. I was wondering what steps I should take and what to be aware of, specifically: 1) having all these different websites on one computer and having the url got to the proper place. 2) Cost effectiveness? Having the server in home as apposed to datacentre. Most solutions I see charge over £1000 a month to have a machine in datacentre. This is mostly for my own ease of management and shared hosting which I currently have is very limited configuration wise. Would getting a server in house be beneficial for then upgrading to the cloud? What measures should I take with my ISP? I know this is a lot I've asked but just even links to good articles would be good. Thanks

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• IP addresses not listed for IIS website bindings

  - by Svinn

  Recently purchased a windows cloud server godaddy. Now i installed iis7 and all other required software. And i have 50.62.1.89 and 2 more public ips. Also i have a private ip 10.1.0.2. Now the problem is am unable to access any website through any public ip. All my public ips are opening default website only. also i cant see pubic ips for IIS website bindings. Only my private ip listed for IIS binding. And in my server also public opening only default website. But am able to open websites using private ip. But my public ip addresses pointed to my server correctly. am able to open my server using remote desktop using public ip. Also as i said already public ip opening default website from IIS without problem. Please help me. Am confused for last 2 days.

  Read the article

• I need a driver for my Cardbus USB 2.0 card

  - by Carl

  The picture and details of the card are here: http://www.ht-link.com/en/ProductView.asp?ID=106 The Windows drivers for this don't work right. I tried them on my previous laptop, and then installed the ones off their included CD. (Note that the systems requirements includes a CD-ROM drive...) I have a new laptop, and lost the CD. The website that lists the drivers is broken - the download links don't work. It is here: http://www.ht-link.com/en/DownView.asp?ID=10 I need the very first link - The Win XP drivers for the HT-112NEC. The company does not reply to my e-mails. I've tried searching Google for other sources for the driver (I didn't bother with those sites that want me to install driver detection software or create a log-in for their site). [Here's the problem I am getting using the drivers Windows XP SP3 installs: When I plug in my USB 2.0 hard-disk adapter, a USB Mass Storage Device entry is added in the Device Manager, but there is no entry under Disk Drives, and a drive letter is not assigned, so I can't access the driver. Like I said, this card didn't work without their special drivers on my other laptop, either.]

  Read the article

• iCloud backup merges or overwrites?

  - by Joe McMahon

  The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• Puppet write hosts using api call

  - by Ben Smith

  I'm trying to write a puppet function that calls my hosting environment (rackspace cloud atm) to list servers, then update my hosts file. My get_hosts function is currently this: require 'rubygems' require 'cloudservers' module Puppet::Parser::Functions newfunction(:get_hosts, :type => :rvalue) do |args| unless args.length == 1 raise Puppet::ParseError, "Must provide the datacenter" end DC = args[0] USERNAME = DC == "us" ? "..." : "..." API_KEY = DC == "us" ? "..." : "..." AUTH_URL = DC == "us" ? CloudServers::AUTH_USA : CloudServers::AUTH_UK DOMAIN = "..." cs = CloudServers::Connection.new(:username => USERNAME, :api_key => API_KEY, :auth_url => AUTH_URL) cs.list_servers_detail.map {|server| server.map {|s| { s[:name] + "." + DC + DOMAIN => { :ip => s[:addresses][:private][0], :aliases => s[:name] }}} } end end And I have a hosts.pp that calls this and 'should' write it to /etc/hosts. class hosts::us { $hosts = get_hosts("us") hostentry { $hosts: } } define hostentry() { host{ $name: ip => $name[ip], host_aliases => $name[aliases] } } As you can imagine, this isn't currently working and I'm getting a 'Symbol as array index at /etc/puppet/manifests/hosts.pp:2' error. I imagine, once I've realised what I'm currently doing wrong there will be more errors to come. Is this a good idea? Can someone help me work out how to do this?

  Read the article

• hyper-v cluster behavior when losing network connectivity

  - by ChristopheD

  Setup: (rather new) Hyper-V R2 cluster with 2 nodes (in failover configuration). Fysical host OS: Windows Server 2008. About eight VM's (mixed: Windows Server 2008 and Linux) Yesterday we had a power outage of about 15 minutes. Our blades are on UPS so the fysical host machines (Windows Server 2008) never went down. Our main switches are not on UPS (yet) and we saw the behaviour similar to the following (as distilled from the event logs). The nodes in the cluster lost means of communication (because the external switches went down). The cluster wants to bring down one (the first) of the nodes (to start failover?). The previous step impacts clustered storage where the virtual machine VHD's are located. All VM's got brutally terminated and were found in a failed state in the failover manager in the host OS'es. The Linux VM's were kernel panicking and looked like they had their disk ripped out. This whole setup is rather new to us, so we are still learning about this. The question: We are putting switches on UPS soon but were wondering if the above is expected behavior (seems rather fragile) or if there are obvious improvements configuration-wise to handle such scenario's ? I can upload an evtx file concerning what exactly was going on in case that's necessary.

  Read the article

• How to setup RAID 1 with Intel RST on an existing Windows 7 system?

  - by instcode

  I'd like to setup RAID-1 using Intel Rapid Storage Technology on my Windows 7 64-bit system. I have an 1TB SATA HDD with Windows 7 system installed on the first primary partition (leftmost, ~200GB). The rest of this HDD is unallocated (~800GB). I bought another 2TB SATA, then created a primary partition (leftmost, ~500GB) and filled my data in. The rest of this HDD is unallocated (~1.5TB). A quick disk layout (XXX is the unallocated region): HDD1 (1TB): [ 200GB C:\ SYSTEM | XXXXXXXXXXXX ] HDD2 (2TB): [ 500GB Z:\ PROGRAM | XXXXXXXXXXXXXXXXXXXXXX ] Now, I want to create a 500GB RAID-1 partition (I'm not sure if using "partition" is correct here) on the rightmost of the 2 HDDs above without losing any existing data from both disks. Here is the expected layout: HDD1 (1TB): [ 200GB C:\ SYSTEM | XXXXXX | 500GB D:\ DATA - RAID-1 ] HDD2 (2TB): [ 500GB Z:\ PROGRAM | XXXXXXXXXXXXXXXX | 500GB D:\ DATA RAID-1] Let's not concern about data lost, is it possible to have that final layout using Intel RST? Previously, I tried this layout using dynamic disk & software RAID from Windows and it worked as expected, however, it's quite ugly in resynching after an OS failure that I don't want. If yes, is there a way to keep the data on existing partitions untouched or, at least, it should keep the SYSTEM partition safe (I'm okay if the PROGRAM partition has to be gone.)? Well, are there any strict/special steps I should follow when using the Intel RST manager in order to achieve that? If none of those questions above are "Yes", could you please suggest some other possible layouts that leave the C:SYSTEM partition untouched?

  Read the article

• Move EFI System Partition to another drive

  - by Pincopallino

  I had a Windows 8 installation on an HDD, using UEFI as boot. The HDD has the following GPT table: DISKPART> list partition Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Ripristino 300 Mb 1024 Kb Partizione 2 Sistema 100 Mb 301 Mb Partizione 3 Riservato 128 Mb 401 Mb Partizione 4 Primario 390 Gb 529 Mb Partizione 5 Primario 540 Gb 390 Gb (I apologize it's in Italian, but the translation is quite straightforward). I recently bought an SSD drive, connected it and installed a fresh Windows 8. Now I have a working dual boot, but the UEFI partition is on the HDD instead of the SSD. Here's the SDD partition list: Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Riservato 128 Mb 1024 Kb Partizione 2 Primario 221 Gb 129 Mb I think that the best solution would be to have it on the SSD for two reasons: the first is performance (I guess it would be a little be faster on the SSD due to the spin up time for an HDD, but I may be wrong about that) second reason is consistency. As I plan to use only the Windows 8 installation that is located on the SSD and I'm probably going to erase the system partition on the HDD to use it as a data storage device, I think that the boot partition should be on the same drive as the OS. So the question is how do I move the EFI System Partition to the SSD?

  Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >