Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 320/778 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

• RRAS Public Address Pool on Windows Server 2008

  - by Art

  I have a Windows 2008 server with two NICs running RRAS and a small public website. It also does NAT for several other PCs on my network and everything works great. I have a block of 5 public static IPs from my ISP, one of which is bound to the public NIC in the Windows 2008 server. I would like to assign one of the remainging 4 public IPs to a machine on my private network. I thought I could do this by going into RRAS, selecting NAT under IPv4 and then adding the public IP address to the address pool and specifying a reservation for the machine I would like to use that address by adding its private ip address. When I do this, the machine I reserved the public IP address for seems to loose all outside network connectivity. I can still ping other PCs on my 192.168.0.* net, but anything outside is no longer reachable. When I remove the reservation, everything seems to work. After setting the reservation and right clicking on the external public interface and selecting 'Show Mappings' I can see outbound requests from my private address with the desired associated private address, however I do not see any inbound requests. What am I doing wrong/missing?

  Read the article

• how does a computer know which IP address will route information to the internet? [closed]

  - by JohnMerlino

  Possible Duplicate: How does IPv4 Subnetting Work? For example, I have a computer with a Network Inteface Card (NIC) which is an Ethernet card that is connected by Ethernet cables to a router. There is also another computer with a cable that is connected in another port of the router. This is a Belkin router operating over an Ethernet in the LAN. When I connect to serverfault.com, it maps to an IP address. My computer now has a task of connecting to that IP address. But my computer itself cannot connect to the serverfault IP address. Only the router can. So the task of my computer is to find the IP address associated with the node that will do the routing to the public internet. How does my computer know that a particular IP address in the local network belongs to the router, and is not another computer connected to the network? Is this information configured manually in the operating system itself? Somehow my computer must know that it must send ethernet frames to the router with the expectation that the router will then send the packet to a public IP. How does it know to send it to the router? Is the router's ip address stored in my computer like a key/value pair e.g. "router"="192.168.2.6", so that when I put a public ip address, my computer first knows to connect to 192.168.2.6?

  Read the article

• Multicast image restoration with adaptive speed

  - by Clinton Blackmore

  I'm curious to know if there are any tools for restoring disk images (or even transferring files) via multicast -- for any platform, especially if the project has source available -- where the multicast rate adjusts itself on the fly. On the Mac, all multicast solutions I am aware of (such as Deploy Studio, and NetRestore before it) make use of multicast ASR (apple software restore), which has one glaring deficiency -- you have to set the multicast speed before you start sending a disk image over the network, and that speed is locked in. Either your clients can keep up and restore, or they can't*. It seems to me that it must be possible for the multicast server to adjust the data rate, so you basically say "start sending this image", clients connect, and, if they can't keep up, they tell the server so it slows down. (Likewise, I'd expect the server to try speeding up if no client is having difficulties keeping up, and I'd expect to be able to cap that maximum throughput so that other network activities can go on without being resource starved.) So, what sort of tools are out there? For Linux? Windows? Is there something for the Mac I've overlooked. [It just kills me that it is true that, by the time you get multicast up and going at a good speed to restore a lab, you could've unicasted the data to all the computers and be done.] * There is a little leeway involved. I think individual clients can say, "I missed a little bit of data" and get it, and they can opt to listen in the next time the image is sent over the network, but on the whole, if they missed it the first go round, you have to image the machine again, and there is no time savings.

  Read the article

• Terminal services printers/scanners?

  - by earlz

  Is there some list of printers/scanners that are known to work with Terminal Services or some way to determine automatically if the device will work from the specifications? I am needing to advise a customer on a small(as in, can set on a desk) all-in-one printer/scanner/fax that works with Terminal Services. The client OS is Windows XP, the server OS is Server 2003.

  Read the article

• Com port redirection from Windows 7 to Windows Server 2008 R2

  - by Ola Eldøy

  We use "Copy file.prn to \tsclient\com1" to print from a TS session to a locally attached serial printer. This works fine from Windows XP, but when trying it from a Windows 7 client computer, we get an "Access is denied" error message. And yes, the check box of COM port is selected on the Local Resources tab of the Remote Desktop Connection client. Any pointers? Has anyone even managed to do this successfully?

  Read the article

• Shared firewall or multiple client specific firewalls?

  - by Tauren

  I'm trying to determine if I can use a single firewall for my entire network, including customer servers, or if each customer should have their own firewall. I've found that many hosting companies require each client with a cluster of servers to have their own firewall. If you need a web node and a database node, you also have to get a firewall, and pay another monthly fee for it. I have colo space with several KVM virtualization servers hosting VPS services to many different customers. Each KVM host is running a software iptables firewall that only allows specific ports to be accessed on each VPS. I can control which ports any given VPS has open, allowing a web VPS to be accessed from anywhere on ports 80 and 443, but blocking a database VPS completely to the outside and only allowing a certain other VPS to access it. The configuration works well for my current needs. Note that there is not a hardware firewall protecting the virtualization hosts in place at this time. However, the KVM hosts only have port 22 open, are running nothing except KVM and SSH, and even port 22 cannot be accessed except for inside the netblock. I'm looking at possibly rethinking my network now that I have a client who needs to transition from a single VPS onto two dedicated servers (one web and one DB). A different customer already has a single dedicated server that is not behind any firewall except iptables running on the system. Should I require that each dedicated server customer have their own dedicated firewall? Or can I utilize a single network-wide firewall for multiple customer clusters? I'm familiar with iptables, and am currently thinking I'll use it for any firewalls/routers that I need. But I don't necessarily want to use up 1U of space in my rack for each firewall, nor the power consumption each firewall server will take. So I'm considering a hardware firewall. Any suggestions on what is a good approach?

  Read the article

• Chrome print background images

  - by Mick

  Hi Im trying to print a php generated document in chrome, on the browser it looks fine But my printer will not print any coloured backgrounds. I know that IE has an option to print background but chrome does not . As the end user will print this off I do not want to find alternatives like a screen grab or save file etc I want to find a real solution to this . Can anyone offer any suggestions please ? Thanks

  Read the article

• Unable to connect to cable modem when connected to VPN

  - by Spuas

  the scenario is as follows: First I have a cable modem which gives the internet connection. The network is 192.168.0.0/24 and its IP is 192.168.0.1 Second line, I have a router connected to the cable modem. Its "outside" IP is 192.168.0.12. This router creates network 192.168.123.0/24 and its IP there is 192.168.123.254. My computer is wired to the router with IP 192.168.123.126. At this point I am able to access both devices web interfaces by their IPs on a browser (192.168.123.254 for the router and 192.168.0.1 for the cable modem). The problem I have is when I connect to a VPN from the computer. Then I am connected to a second network 10.0.0.0/24 and I get IP 10.0.0.200 (along with 192.168.123.126). I can connect to the router but then I loose connectivity to the cable modem: I cannot acces it through the browser, neither making a ping to it or a tracert. I have tried to add a new route to the windows routes by typing route ADD 192.168.0.1 MASK 255.255.255.0 192.168.123.254 but I cannot access it anyway... Am I missing something on the route adding? Which is the propper way of doing this? Thanks

  Read the article

• Windows Explorer slow to open networked computer, fast to navigate once opened

  - by Scott Noyes

  I open Windows Explorer and enter an IP for a computer on my home network (\\192.168.1.101). It takes 30 seconds or more to present a list of the shared folders. It does not appear to be an initial handshaking/authentication thing; even if I allow the view to load and then immediately load the same again, it is always slow. Once they appear, navigating through folders and opening files is fast. Also, navigating directly to a folder (\\192.168.1.101\My Music) is fast, even if it's the first connection since a restart. Using \\computerName instead of the IP address gives exactly the same results. Pings return in 1ms. net view \\computerName (or \ipAddress) returns the list of shared folders fast. This makes me suspect an Explorer issue rather than a network issue. Suspecting that the remote computer was being automatically indexed or something, I went into Tools-Folder Options-View and unchecked "Automatically search for network folders and printers," but that made no difference. De-selecting the "Folders" icon near the address bar makes no difference. Adding the IP address and computer name to the hosts file makes no difference. Both computers involved are laptops running Windows XP. Both have WiFi and cable adapters. Mine is not connected via cable. The result is the same whether the target is plugged in to the cable or not (although the IP address changes - 192.168.1.101 over cable, 192.168.1.103 over WiFi.) We are using DHCP assigned by the router.

  Read the article

• Retiring a print server but looking for a method to confirm no one is still connecting to it

  - by Richard West

  I have a Windows 2003 print server that I need to retire. Through variaous methods (login scripts, etc) I think that I had everyone migrated off of this server and connected to the new print server. Having said that, I'd like to make sure before taking the server down :-) Is there a script that I can run to query a remote workstations in my domain to see what printer shares it is connected to?

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Removing forward lookup zone broke our site - why?

  - by user102469

  I'm fairly new to the job and trying to get to grips with the infrastructure here. We've moved a site from being locally hosted on our own network to an external host (1&1). I've transferred the DNS hosting from the previous DNS host to 1&1 to keep things simple. Once everything had gone through, visitors that were external to our network were being directed to the new site on 1&1 but requests from within our network were still going to our own server. I noticed in the DNS server that there was a forward lookup zone for the site pointing to our own server still. My (admittedly simplistic) understanding was that pausing that zone would then cause the DNS server to get the address for the site from our external DNS servers and our users would start landing on our new site. However, what happened instead was that they were being met with "page not found" type errors. I've resolved it my modifying the forward lookup zone A record to point to the external web server but would like to get an understanding as to why pausing the zone didn't work. Would deleting the zone work? I am reluctant to try that as creating it again will not be as easy as simply pressing "start". Many thanks.

  Read the article

• Allowing XP Home Clients To Access Active Directory Printers

  - by Sean M

  My school's network is based on Active Directory on Windows Server 2003 servers. Most of the computers in the school are members of the domain. However, we also acquired a passel of netbooks that are running Windows XP Home (as netbooks tend to), and we're trying to make those useful. The netbooks are made available to students by check-out, so none of them are dedicated to a specific user. I only want to allow the netbooks to do two significant network activities: to access the Internet (this is working acceptably well so far), and to print to one or more printers on the network. That second one is where trouble starts. I'm trying to find a way to allow the XP Home clients to access those Active Directory printers. All the solutions that I can come up with right now are expensive, ugly, or both - for example, changing the OS on the netbooks (even with imaging, that would take a lot of my time) or making sure that the user account on each netbook has a matching account in Active Directory with permissions for printing (invites security/maintainability disaster). Are there any elegant solutions? Failing that, what's the best ugly solution for allowing my students to print from the netbooks?

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• Debian: Should I add vlan interface into bridge for KVM?

  - by javano

  I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is to add multiple logical VLAN (sub)-interfaces to the physical NICs and then create a bridge adapter for each VLAN interace, and assign each bridge as a NIC for KVM guests. Does this make good sense, or madness? Do I have to use bridged interfaces with KVM like this? Can't I just add eth1.xx and eth1.yy to my interfaces config below and then configure those directly as bridged KVM guest NICs? If so, how should this look in the interfaces config file below? user@host:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # Management Interface auto eth0 iface eth0 inet static address 172.22.0.31 netmask 255.255.255.0 gateway 172.22.0.1 # Interface for guest VMs auto eth1 # Guest1 : Use VLAN 117 auto eth1.117 iface eth1.117 inet manual # Set up br1 for guest 1, bridging with vlan 117 auto br1.117 iface br1.117 inet manual bridge_ports eth1.117 bridge_stp off user@host:~$ uname -a Linux hostname 3.4.9 #1 SMP Wed Aug 22 19:08:46 BST 2012 x86_64 GNU/Linux UPDATE I would really like it if someone could clarify the config for me, as I have also seen the above configured with this syntax, so I don't see why one would be preferred over the other; # Interface for guest VMs auto eth1 allow-hotplug eth1 iface eth1 inet static # Vlan 117 for guest 1 auto vlan 117 iface vlan111 inet static vlan_raw_device eth1 # Guest 1 : NIC 1 auto br1.117 iface br1.117 inet manual bridge_ports vlan117 bridge_stp off

  Read the article

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• Cannot connect with Cisco VPN but can connect with ShrewSoft VPN

  - by rodey

  EDIT: We connected an air card to the computer to use a different Internet connection and using the Cisco software, we were able to successfully connect to our VPN server. I just don't understand why the ShrewSoft VPN client would connect but the Cisco connection won't. I'm not our network admin so sorry if I butcher some of the terminology. I have a computer at remote site that connects to our network through Cisco VPN. It uses the Cisco VPN software to do so. The problem is that the computer at this site cannot connect to our VPN because it is getting error "Reason 412: The remote peer is no longer responding." To see if perhaps something on their network was blocking the connection, I installed the ShrewSoft VPN client on the computer, imported our .pcf file and connected with no problem. I have tried two different versions of the Cisco VPN software (4.8.0.* and 5.0.03.*) and have the same problem. I installed Wireshark on the computer and have confirmed (while trying to connect through Cisco) that the computer is trying to contact the VPN server but is not receiving a response. We are not having any other problems regarding users not being able to connect. I'm at a loss at what else to check. I'll be monitoring this and have access to the computer at any time.

  Read the article

• Make case-sensitive SMB share case-insensitive

  - by fungs

  I am running a legacy XP app that I would like to move on a network share. It is very simple and works in theory but the server providing the share is based on Linux (cannot configure) and the software does not work correctly because it is programmed case-insensitively, it seems. After some research, network shares behave like the filesystem they use underneath. This is normal. Unfortunately I cannot fix the software myself. Is there any way to turn the case-sensitivity into case-insensitivity for a Windows network drive on the client side? I fould two approaches: First, something like icasefile (http://wnd.katei.fi/icasefile/) that wraps around the program and intercepts the file I/O. This is for UNIX only. Secondly, a proxy virtual file system (e. g. something using Dokan). Unfortunately I couldn't find any suitable fs, the only possibility would be to put a case-insensitive filesystem on an image file and put this on the share using for example lmdisk (http://www.ltr-data.se/opencode.html/#ImDisk). Do you have any better ideas?

  Read the article

• USB-to-Parallel adapter rated as USB 1.1 - will its driver lower speed of USB 2.0 bus?

  - by cumminjm

  I need to connect a printer with a parallel port to a computer with only a USB 2.0 bus. I'd like to do so without lowering the USB 2.0 bus speed to USB 1.1. All the USB-to-Parallel adapter cable found so far seem to be rated as USB 1.1 and they come with a CD which presumably contains a necessary driver. I haven't purchased one and tested it out yet, but if so, would the cable's driver lower speed of USB 2.0 bus?

  Read the article

• Cisco ASA 5510 Time of Day Based Policing

  - by minamhere

  I have a Cisco ASA 5510 setup at a boarding school. I determined that many (most?) of the students were downloading files, watching movies, etc, during the day and this was causing the academic side of our network to suffer. The students should not even be in their rooms during the day, so I configured the ASA to police their network segment and limit their outbound bandwidth. This resolved all of our academic issues, and everyone was happy. Except the resident students. I have been asked to change/remove the policing policy at the end of the day, to allow the residents access to the unused bandwidth at night. There's no reason to let bandwidth sit unused at night just because it would be abused during the day. Is there a way to setup Time of Day based Policies on the ASA? Ideally I'd like to be able to open up the network at night and all day during weekends. If I can't set Time based policies, is is possible to schedule the ASA to load a set of commands at a specific time? I suppose I could just setup a scheduled task on one of our servers to log in and make the changes with a simple script, but this seems like a hack, and I'm hoping there is a better or more standard way to accomplish this. Thanks. Edit: If there is a totally different solution that would accomplish a similar goal, I'd be interested in that as well. Free/Cheap would be ideal, but if a separate internet connection is my only other option, it might be worth fighting for money for hardware or software to do this better or more efficiently.

  Read the article

• VMWare converter performance

  - by bellocarico

  Hello, I have a question about my test lab. It's more to understand the concept more than apply this into production: I have an ESXi with few VMs linux/windows configured and I'd like to use VMWare converter to create backups. To speedup the process I decided to create a Windows VM on the same ESXi host where I've installed Windows 7 and VMWare Converter. The Host has a gigabit card but it's currently connected to a 100Mb FD port. Windows 7 sees a 1gb card connected. When I do the backup using VMWare converter I specify the host IP as source and destination, so I thought the copy could be faster then use my laptop across the network. Well, to cut a long sotry short: I get dreadful performance (4Mb/sec). I'm a buit confused on this because despite the fact that the host is running 100Mb communication between VMs and hosts shouldn't (correct me if I'm wrong) have any limitation instead. I did tweak windows 7 to optimise network performane but I got just a little improvement. i still need 4 hours to back up a 50Gb (thin) VM. Additionally I wanted to ask: Would jumbo frame help in this? I know that jumbo frame have to be supported end to end, and the network switch where the host is currently connected doesn't support this, but I was wondering: 1) Does ESXi host support jumbo frames at all? 2) Can I enable it somehow? 3) If I do so, I guess bulk transfert between VMs and host would improve, but would this affect the communication going through the real switch as this doesn't do jumbo? Thanks for reading

  Read the article

• Firebox 1250e Core Failing?

  - by Noah

  We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

  Read the article

• Using proxy.pac to access Apache 2 with a hostname?

  - by leeand00

  Note that I do not have a DNS on my network, and that is why I am resorting to using a proxy.pac file. I would like to be able to access my development Apache 2 server using a name instead of an ip without setting up a full blown DNS. I am aware of setting names in the C:\Windows\System32\drivers\etc\hosts file and the /etc/hosts files, however I cannot edit the hosts file on all of the devices that I am testing the site on. I've added a proxy.pac file to my Apache2 server and pointed my browsers settings to it at: http://192.168.2.221/proxyutils/proxy.pac ...where 192.168.2.221 is thehostname's ip address. I set the above URL in Firefox in the following manner: From the menubar selecting "Edit-Preferences" In the resulting "Firefox Preferences" window clicking the "Advanced" tab. Clicking the "Network" tab Clicking the "Settings" button. Selecting the "Automatic proxy configuration URL:" radio button. Entering http://192.168.2.221/proxyutils/proxy.pac and pressing OK. The contents of the proxy.pac file on the Apache server function FindProxyForURL(url, host) { if( dnsDomainIs(host, "thehostname") ) return "PROXY 192.168.2.221:80"; return "DIRECT"; } In Firefox I then access the following URL: http://thehostname/wp-blog/ And instead of the development version of the Wordpress blog I am trying to access I get a URL of http://thehostnamehttp/thehostname/wp-blog/ in my address bar and a 404 Not Found page in the browser window. Looking over proxy.pac, it seems like calling dnsDomainIs shouldn't work considering I don't have a DNS setup on my network, but I've also tried just comparing the host argument with the string "hostname" and it yielded the same result, even after modifying the proxy.pac file and clicking the reload button near the proxy settings. This could also be a Wordpress problem, since I've noticed that directories without Wordpress seem to function perfectly normally. (see cross post here) Is there any way I can modify my configuration so that I can access the site using http://thehostname/wp-blog/ ?

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• How can I change the default location/action of 'Open Outlook Data File' in Outlook 2010?

  - by Chadddada

  I have recently deployed a Remote Desktop Host server that functions as a remote Microsoft Office 2010 work space for users. In part of the locking down of this server I have installed all programs on the D: drive and, through the use of Group Policy, hidden all the drives on the server from standard users. In addition to hiding these drives I am not allowing users to save anything locally (on the server) or open Libraries. However one of the functions of the server is to provide the Outlook client. Often users will have the .PST file stored on a network location and want to open this in Outlook. Can I change the default action or location that File Open Open Outlook Data File looks or tries to pull the file from? The default location seems to be under Users / Libraries. When click 'Open' you get a warning: This operation has been cancelled due to restrictions in effect on this computer. Clicking OK drops the user into a small menu that shows attached network drives under Computer. Can I instead have the 'Open' click drop the users in a defined network drive or just open computer and allow them to select a share? I don't want them to see the error message. A solution that looks to have been used for Office 2000/03 is: Key: HKEY_CURRENT_USER\Software\Microsoft\Office\<version>\Outlook Value name: ForceOSTPath Value type: REG_EXPAND_SZ Value: path to your storage folder I am not sure if there is a better way to do this now OR if this even works with Office 2010.

  Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >