Search Results

Search found 13434 results on 538 pages for 'boot on power up'.

Page 322/538 | < Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >

• Good Linux disaster-ready filesystem?

  - by Felipe Solís

  I'm working on this emergency open wi-fi network project and it includes a local website (nginx + MySQL). In order to eliminate SPOFs, we're going to setup at least two of everything (server, switch, router, etc.). This network is thought to work when an earthquake strikes and it's very likely to a server to go to down, if so, we need to be able to boot them up and be operating as soon as possible. Do any of you know if any linux filesystem would work better than others in this scenario?

  Read the article

• Add a small RAID card? Will it help overall stability and performance of my nine hard drives?

  - by Ray

  Hi, Will I get any extra genuine added performance and RAID stability if I insert a basic RAID card into a PCI-E x1 slot? I am considering the Adaptec 1220SA - 2 port SATA , pci-express (1x) , raid 0/1. Ok it only supports two SATA drives. Purpose is to help support the eight internal hard drives (1TB each), a DVD drive and an external e-SATA connected 2TB hard drive - by dealing with two of the internal hard drives. My current configuration of eight internal 1TB Barracuda (7200.12) SATA hard drives, one external 2TB SATA Western Digital Green Drive (e-SATA) and one DVD drive can already be supported by the Intel P55 & JMicron controllers on the ASUS motherboard : the Intel P55 (controls six HDD; configured as three x RAID 1), and the JMicron (controls two HDD as one RAID 1, as well as the DVD drive and the external SATA drive via the motherboard's e-SATA port (controlled by the JMicron)). Bigger picture details : I have an ASUS motherboard designed for the LGA1156 type processor and it includes the Intel P55 Express Chipset and JMicron. I am using the Intel Core i7-870 processor, and have 8GB DDR3 (1333) memory (four x 2GB Corsair DIMMs). Enough overall power. The power supply is more than sufficicient for the system. Corsair AX850. The system will never need the full 850 watts (future : second graphics card). The RAID card would provide hardware RAID 1 for two of the eight intrnal drives. It would either reduce the load on : the Intel P55 firmware RAID support, or replace the JMicron controller's RAID 1 set. I am busy installing the above configuration using Windows 7 Ultimate 64-bit as the OS. The RAID card is a last minute addition to the plan. Is it worth spending the extra R700 - R900 on the Adaptec 1220SA, or equivalent RAID card? I cannot afford to spend yet another R2000 - R3000 on a RAID card that would support many SATA2 hard drives, with a better RAID, example the RAID 5. My Issue & assumption : I am trusting that the Intel P55 chipset can properly handle six drives, configured as three * RAID 1. I am assuming that the JMicron can handle, using its RED SATA ports, one RAID-1 (two HDDs). The DVD drive connects to the JMicron optical SATA port 1 (white port 1). White port 2 is not used. The e-SATA connection is from the JMicron straight to, and through the motherboard - to an on-board (rear panel) e-SATA port. Am I being a little hopeful in only using the on-board Intel P55 and the JMicron? Is it a waste of money to install a RAID card that handles two SATA2 drives? OR Is it wisdom to take the pressure a little off the Intel P55? Obviously I am interested in data security, hence RAID 1, not RAID Zero. RAID 5 would be nice. The CPU, Intel Core i7-870 will provide the clout. Context to nine drives : I am using virtualisation with Windows 7 Ultimate. Bootable VMs. The operating system gets a mirror. Loaded apps gets a mirror. The current design data is kept in another mirror and Another mirror is back-up one and / or VM territory. Then the external 2TB drive (via e-SATA) is the next layer of data security and then finally, I use off-site data security. Thanks.

  Read the article

• FreeBSD running in Hyper-V

  - by dmo

  I'd like to install FreeBSD 8.0 in a Hyper-V VM but I get a kernel panic whenever I try to boot the install ISO. I've tried both i386 and amd64; with and without APIC enabled; with and without processor features disabled in Hyper-V. Is it necessary to use the procedure in the Handbook for Xen domU? Does anyone has experience with this configuration?

  Read the article

• how do i turn air port on in windows 7?

  - by Ioan

  I have a macbook 2010 and i instaled windows 7 ultimate using boot camp. I can't connect to the internet. I have a wireless rooter in my house. IE say's that maybe the wireless adapter isn't turned on. How do i connect to the internet without using a cable? ty

  Read the article

• Prime95 daul-core tool?

  - by Ssvarc

  Does Prime95 use multiple cores? (Is there a difference in this regard between running it from Windows, UBCD, or UBCD4Win?) If it doesn't, are there tools out there that will (preferably via a boot disc)? Thanks!

  Read the article

• How decode xfs lost+found directory

  - by Satpal

  I have managed to trash my homebrew Nas box (an old hp d530 + 2x 750gb sata soft raid1 + 17gb boot disk with ubuntu server 8.10) I have searched the web and tried to repair the file system but to no avail :( I was thinking that the dirs/files located under the root of the lost+found directory are 64 bit numbers. Is there any way that I could decant the number into binary form, from there reconstruct the directory/file structure. More to the point can anyone point to the information on how xfs inodes are broken down(does that make sense)?

  Read the article

• Cloning an LVM disk with dd?

  - by joeforker

  I would like to clone a smaller LVM-formatted disk onto a larger one using dd, and boot that disk in the same machine. Do I need to make any special considerations for LVM?

  Read the article

• Hitachi DFT hangs - Causes and workarounds?

  - by Ssvarc

  Hitachi DFT hangs (it gets all the way to "Loading DFT" and hangs with a blinking cursor) when I use it on various computers (the latest computer to hang being a Dell Vostro 1000 laptop) and works on others. What determines when it will hang and when it won't? What similar program can I use (boot CD) that can determine HD health reliably? Thanks!

  Read the article

• XP Suddenly asking for password

  - by ProfKaos

  Is there any sane explanation for a client's Acer Aspire 1 netbook, running XP Home SP 2, suddenly starting to ask for a login password at boot? He has a strict policy of not using passwords, and I removed his login password weeks ago. The story is that suddenly this morning, for the first time, it is asking for a login password.

  Read the article

• XP Suddenly asking for password

  - by ProfKaos

  Is there any sane explanation for a client's Acer Aspire 1 netbook, running XP Home SP 2, suddenly starting to ask for a login password at boot? He has a strict policy of not using passwords, and I removed his login password weeks ago. The story is that suddenly this morning, for the first time, it is asking for a login password.

  Read the article

• Not able to Defrag my drive for shrink even using PerfectDisk on Windows 7

  - by Mithun Sasidharan

  I want to partition my c drive which has over 450gb capacity of which hardly 30gb is being used. I deleted the pagefile.sys and also disabled hibernate and cache memory. I then defragmented and consolidated free space using PerfectDisk 12 and also run a boot time defragmented. Now what remains is Metadata files that preventing me from shrinking the volume beyond half the size if disk. Please tell me what to do?????

  Read the article

• Rocksclusters reinstalling nodes partitioning error.

  - by Antiarchitect

  I have a HPC based on rocksclusters So when I've added new roll (torque) I send a kickstart command to all nodes to reinstall them. But after loading X installer on nodes all of them showed me an error: Could not allocate requested partitions: Partitioning failed: Could not allocate partitions as primary partitions. Cannot allocate partition for /boot

  Read the article

• downgrade the system

  - by deddihp

  hello, actually i have some business to downgrade the kernel. I downgrade from kernel 2.6.31-14 (ubuntu 9.10) to 2.6.26.8. And then i got the following error in my boot process : warning: unable to find a suitable fs in /proc/mounts, is it mounted ? use --subdomainfs to override what is that mean anyway ? thanks.

  Read the article

• Authenticate to VM using vagrant up

  - by utrecht

  Authentication failure during Vagrant Up, while vagrant ssh and ssh vagrant@localhost -p2222 works I would like to execute a shell script using Vagrant at boot. Vagrant is unable to Authenticate, while the VM has been started using vagrant up: c:\temp\helloworld>vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Importing base box 'helloworld'... ==> default: Matching MAC address for NAT networking... ==> default: Setting the name of the VM: helloworld_default_1398419922203_60603 ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2222 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2222 default: SSH username: vagrant default: SSH auth method: private key default: Error: Connection timeout. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... ... After executing CTRL + C it is possible to authenticate to the VM using vagrant ssh and ssh vagrant@localhost -p2222 Vagrant file I use the default Vagrantfile and I only changed the hostname: # -*- mode: ruby -*- # vi: set ft=ruby : # Vagrantfile API/syntax version. Don't touch unless you know what you're doing! VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| # All Vagrant configuration is done here. The most common configuration # options are documented and commented below. For a complete reference, # please see the online documentation at vagrantup.com. # Every Vagrant virtual environment requires a box to build off of. config.vm.box = "helloworld" ... Vagrant version c:\temp\helloworld>vagrant --version Vagrant 1.5.1 Question How to authenticate to VM using vagrant up?

  Read the article

• Connect ps/2->usb keyboard to linux?

  - by Daniel

  I have a lovely ancient ergonomic keyboard (no name SK - 6000) connected via a DIN-ps/2 adapter to a ps/2-usb adapter to my docking station. After Grub it stops working. It takes either suspending and waking up or replugging it while Linux is running to get it to work. No extra kernel modules get loaded for this. When it works and I restart without power off, it will work immediately. Even when it does not work, it is visible (lsusb device number varies but output is identical whether working or not): $ lsusb -v -s 001:006 Bus 001 Device 006: ID 0a81:0205 Chesen Electronics Corp. PS/2 Keyboard+Mouse Adapter Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x0a81 Chesen Electronics Corp. idProduct 0x0205 PS/2 Keyboard+Mouse Adapter bcdDevice 0.10 iManufacturer 1 CHESEN iProduct 2 PS2 to USB Converter iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 59 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 2 PS2 to USB Converter bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 1 Keyboard iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 64 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 148 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) $ ll -R /sys/bus/hid/drivers/ /sys/bus/hid/drivers/: total 0 drwxr-xr-x 2 root root 0 Jul 8 2012 generic-usb/ /sys/bus/hid/drivers/generic-usb: total 0 lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:046D:C03D.0003 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/0003:046D:C03D.0003/ lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:0A81:0205.0001 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/ lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:0A81:0205.0002 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.1/0003:0A81:0205.0002/ --w------- 1 root root 4096 Jul 7 23:32 bind lrwxrwxrwx 1 root root 0 Jul 7 23:33 module -> ../../../../module/usbhid/ --w------- 1 root root 4096 Jul 7 23:32 new_id --w------- 1 root root 4096 Jul 8 2012 uevent --w------- 1 root root 4096 Jul 7 23:32 unbind When replugging, dmesg shows this (which except for the 1st line and different input numbers already came at boot time): [ 1583.295385] usb 1-1.2.1: new low-speed USB device number 6 using ehci_hcd [ 1583.446514] input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/input/input17 [ 1583.446817] generic-usb 0003:0A81:0205.0001: input,hidraw0: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:00:1a.0-1.2.1/input0 [ 1583.454764] input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.1/input/input18 [ 1583.455534] generic-usb 0003:0A81:0205.0002: input,hidraw1: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:00:1a.0-1.2.1/input1 [ 1583.455578] usbcore: registered new interface driver usbhid [ 1583.455584] usbhid: USB HID core driver So I tried $ sudo udevadm test /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 run_command: calling: test adm_test: version 175 This program is for debugging only, it does not run any program, specified by a RUN key. It may show incorrect results, because some values may be different, or not available at a simulation run. parse_file: reading '/lib/udev/rules.d/40-crda.rules' as rules file parse_file: reading '/lib/udev/rules.d/40-fuse.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/40-usb-media-players.rules' as rules file parse_file: reading '/lib/udev/rules.d/40-usb_modeswitch.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/42-qemu-usb.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/69-cd-sensors.rules' as rules file add_rule: IMPORT found builtin 'usb_id', replacing /lib/udev/rules.d/69-cd-sensors.rules:76 ... parse_file: reading '/lib/udev/rules.d/77-mm-usb-device-blacklist.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/85-usbmuxd.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/95-upower-hid.rules' as rules file parse_file: reading '/lib/udev/rules.d/95-upower-wup.rules' as rules file parse_file: reading '/lib/udev/rules.d/97-bluetooth-hid2hci.rules' as rules file udev_rules_new: rules use 271500 bytes tokens (22625 * 12 bytes), 44331 bytes buffer udev_rules_new: temporary index used 76320 bytes (3816 * 20 bytes) udev_device_new_from_syspath: device 0x7f78a5e4d2d0 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' udev_device_new_from_syspath: device 0x7f78a5e5f820 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' udev_device_read_db: device 0x7f78a5e5f820 filled with db file data udev_device_new_from_syspath: device 0x7f78a5e60270 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001' udev_device_new_from_syspath: device 0x7f78a5e609c0 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0' udev_device_new_from_syspath: device 0x7f78a5e61160 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1' udev_device_new_from_syspath: device 0x7f78a5e61960 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2' udev_device_new_from_syspath: device 0x7f78a5e62150 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1' udev_device_new_from_syspath: device 0x7f78a5e62940 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1' udev_device_new_from_syspath: device 0x7f78a5e630f0 has devpath '/devices/pci0000:00/0000:00:1a.0' udev_device_new_from_syspath: device 0x7f78a5e638a0 has devpath '/devices/pci0000:00' udev_event_execute_rules: no node name set, will use kernel supplied name 'hidraw0' udev_node_add: creating device node '/dev/hidraw0', devnum=251:0, mode=0600, uid=0, gid=0 udev_node_mknod: preserve file '/dev/hidraw0', because it has correct dev_t udev_node_mknod: preserve permissions /dev/hidraw0, 020600, uid=0, gid=0 node_symlink: preserve already existing symlink '/dev/char/251:0' to '../hidraw0' udev_device_update_db: created empty file '/run/udev/data/c251:0' for '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' ACTION=add DEVNAME=/dev/hidraw0 DEVPATH=/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 MAJOR=251 MINOR=0 SUBSYSTEM=hidraw UDEV_LOG=6 USEC_INITIALIZED=969079051 The later lines sound like it's already there. And none of these awakes the keyboard: $ sudo udevadm trigger --verbose --sysname-match=usb* /sys/devices/pci0000:00/0000:00:1a.0/usb1 /sys/devices/pci0000:00/0000:00:1a.0/usbmon/usbmon1 /sys/devices/pci0000:00/0000:00:1d.0/usb2 /sys/devices/pci0000:00/0000:00:1d.0/usbmon/usbmon2 /sys/devices/virtual/usbmon/usbmon0 $ sudo udevadm trigger --verbose --sysname-match=hidraw0 /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 $ sudo udevadm trigger I also tried this to no avail: # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/bind ksh: echo: write to 1 failed [No such device] # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/unbind # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/bind # echo usb1 >/sys/bus/usb/drivers/usb/unbind # echo usb1 >/sys/bus/usb/drivers/usb/bind What else should I try to get the same result as replugging or suspending, by just issuing a command?

  Read the article

• Ubuntu 10.04 (LTS) DomU on Debian Wheezy Dom0 Xen 4

  - by mdjp

  I have been forced to move from a Centos Dom0 xen 3 Centos + Ubuntu Lucid DomUs To Debian Wheezy Dom0 Xen 4 Ubuntu Lucid DomUs However although I can create new DomUs on wheezy I cannot get them to boot. pygrub returns Error: Bootloader didn't return any data I have ensured that the disks are the correct way around in the xen.cfg and also that the grub config is correct. If I try to run pygrub manually eg /usr/bin/pygrub /dev/volgroup/disk I get Illegal instruction can anyone offer me any advice on this? Thanks Matt

  Read the article

• xp black screen

  - by ciss

  Hello, sorry for my english, i am from russia. so, my pc based on AMD athlon. In past i move harddrive with xp and insert this HardDrive to another PC (Intel core2duo) I do this because i need a lot of files from my pc to another. So after this i back my harddrive to original pc (amd) And i see blackscreen on win-loading! (additional info - i boot this hard on another pc ... i know this is bad =(

  Read the article

• XFS disk becomes unavailable after a while

  - by Guard

  Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

  Read the article

• Ubuntu: USB drive = /dev/sda1?

  - by lipton

  I'm trying to boot Ubuntu from my USB drive. How do I know the drive name in Ubuntu since I haven't installed Ubuntu yet? This guy is using /dev/sda1 for his USB drive. How did he figure that out?

  Read the article

• Dell XPS Problem

  - by Alex B.

  Hi, Yesterday, my mom dropped her laptop to the floor and got the blue screen of death after trying to boot the system. I was able to start fedora live CD and get some of her stuff off the hard drive, but I cannot seem to be able to install Windows on it. The installation starts loading files and then the computer turns off. I am thinking that she might need a new hard drive. Any ideas?

  Read the article

• Server restarted while rebuilding array, what to do?

  - by user239054

  It's a HP ProLiant DL380 Generation 7, that has four hard drives, one is dead, I suppose that another one is dead too, but is there any way to force the array to rebuild again? The server has restarted while it was rebuilding an array. My windows server(2008) that is on it won't boot, it goes directly to system recovery screen. I have an image backup, would restoring it be my only option?If I restore, it will get back to regular automatically or will I have to configure something?

  Read the article

• Windows 7 Ultimate Restore From Another Machine

  - by Guy Thomas

  The situation I have an old machine running Windows Server 2008. I make a backup of selected directories. New Machine: I install Windows 7 Ultimate (and Windows Server 2008 [dual boot]) I cannot restore those files that I backed-up on the old machine. On the New machine neither the Windows 7 or Windows Server 2008 Restore (Recovery) can 'see' the backup files even though they are on the local machine. Is this behaviour (non-behaviour) 'by design' or am I missing something?

  Read the article

• How to install debian oldstable from network?

  - by Vi.

  I use PXE debian installer and install it from the local network mirror. It only offers to install "squeeze - stable" despite of there are both squeeze and lenny on the mirror. How to force it to install oldstable (lenny)? When I use legacy network-boot installer, it offers both "oldstable - lenny" and "stable - squeeze", but when I use new one it only offers "stable - squeeze". Can the new installer install old Debian?

  Read the article

• Amazon EC2 root defaults on EBS

  - by CodeShining

  I'm trying to understand why when launching a new instance Amazon defaults to EBS (8gb root) instead of instance storage. Why do they sell instance storage then if it's not used also to boot the base system? Is it safe to uncheck delete on termination, make it bigger (~50GiB) and keep all files on that EBS instead of creating a new one to make sure data will persist and it will also be usable by another instance?

  Read the article

• Windows not remembering default audio device?

  - by Lynda

  I prefer the audio output on my computer to use the standard audio jack output due to volume issues. But I am using a monitor with HDMI. I have chosen to set the default audio device to be "Speakers" But every time I reboot the default audio device is the HDMI Output again. I am running Windows 7 64bit. Why does it not remember the default device? (I do shutdown and boot up properly without errors.)

  Read the article

< Previous Page | 318 319 320 321 322 323 324 325 326 327 328 329  | Next Page >