Search Results

Search found 18916 results on 757 pages for 'sharing nothing architect'.

Page 328/757 | < Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >

• why is port 500 in use and how can I free it? VPNC error

  - by kirill_igum

  i tried to use network manager to connect to my university's vpn; it didn't work. then i used a command line vpnc: > sudo vpnc [sudo] password for kirill: Enter IPSec gateway address: vpn.net.**.edu Enter IPSec ID for vpn.net.**.edu: ** Enter IPSec secret for **@vpn.net.**.edu: Enter username for vpn.net.**.edu: ** Enter password for **@vpn.net.**.edu: vpnc: Error binding to source port. Try '--local-port 0' Failed to bind to 0.0.0.0:500: Address already in use then i did this: sudo vpnc --local-port 0 with the same config and it all worked. i'd like to be able to use network manager gui to connect to vpn. I wanted to find out which program uses the port 500: > sudo netstat -a |grep 500 tcp 0 0 *:17500 *:* LISTEN udp 0 0 *:4500 *:* udp 0 0 *:17500 *:* unix 3 [ ] STREAM CONNECTED 63500 unix 3 [ ] STREAM CONNECTED 12500 @/tmp/.X11-unix/X0 there is nothing that uses 500 i'm using ubuntu 10.10 on thinkpad x201t

  Read the article

• USB 3.0 port with USB 3.0 device in Ubuntu 12.10

  - by fernando garcía

  When I try to connect a USB 3.0 device in Ubuntu 12.10 (ASUS K55VD, kernel 3.5.0-19-generic #30-Ubuntu SMP), the system says [ 74.747832] hub 3-0:1.0: unable to enumerate USB device on port 1 [ 74.931957] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd [ 74.949390] usb 4-1: New USB device found, idVendor=05e3, idProduct=0731 [ 74.949396] usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2 [ 74.949400] usb 4-1: Product: USB Storage [ 74.949403] usb 4-1: SerialNumber: 0000000000000033 [ 75.033327] usbcore: registered new interface driver uas [ 75.038548] Initializing USB Mass Storage driver... [ 75.038651] scsi7 : usb-storage 4-1:1.0 [ 75.038700] usbcore: registered new interface driver usb-storage [ 75.038701] USB Mass Storage support registered. but it does not recognize the device, and the disks applications (gparted, nautilus) act as if nothing had been connected. I have checked other questions, but either they have no answers or they told about previous Ubuntu version with 3.0.x kernels. A USB 2.0 device will work in the USB 3.0 ports. A USB 3.0 device will work (at USB 2.0 speeds) in the USB 2.0 ports. The problem, as I wrote, is between USB 3.0 devices and USB 3.0 ports. I have my USB 3.0 ports configured without legacy support via the BIOS (the way they should be, I suppose). But I also have tried to configure them with XHCI Preboot mode disabled. Have any one solved a similar problem? Thanks in advance.

  Read the article

• Windows 2003 VM, not connecting to VM Network

  - by TheWellington

  I am running VMware's vSphere infrastructure. I have a windows 2003 VM that is suddenly not connected to the network. I can log into vSphere and see that the VM is running, but it does not connect to the VM network. The firewall on this VM is not running. The network adapter in the VM is configured correctly. The only evidence I see indicating an issue is in the event viewer. I have the following entry. Source: VMUpgradeHelper EventID: 270 Description: Not restoring network configuration for adapter with MAC address 00:50:56:xx:xx:xx. The device ID for this adapter is unchanged. THis VM is a webserver, and it was working beautifully just two days ago. "nothing" has happened... so I am at a loss as to what may have happened. Ideas??

  Read the article

• Zantaz's EAS exchange archive product doesn't integrate with Outlook in Windows 7

  - by Chris Farmer

  I work at a place that uses Exchange with Outlook for mail, and they also use a product from Zantaz called "EAS" which does server-side archiving of old messages. One of the artifacts of this archival is that email attachments are missing from the archived messages when viewed in Outlook. EAS has a client tool that plugs into Outlook that enables easy retrieval of those archived messages and their attachments, but it doesn't seem to work when installed on Windows 7. I have no direct evidence of this, other than that it simply doesn't work on my Windows 7 machine, and some of our network support staff seem to corroborate this. The symptom is that Outlook seems to know nothing of the existence of this EAS app. The EAS app also has a system tray icon which is there and offers some minimal functionality, but the real goodness is the Outlook integration, which I sorely miss. So, my question is this: does anyone here know whether it's possible to coerce this EAS product into working correctly in Windows 7?

  Read the article

• Problems compiling scangearmp

  - by maat

  I have already installed some missing packages, but i still get that error. Can anyone help me identify what is missing ? Thanks a lot psr@psr-EasyNote-TM85:~/Downloads/scangearmp-source-2.10-1/scangearmp$ make make all-recursive make[1]: Entering directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp' Making all in po make[2]: Entering directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp/po' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp/po' Making all in backend make[2]: Entering directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp/backend' /bin/bash ../libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -I.. -I. -I./include -DV_MAJOR=2 -DV_MINOR=1 -O2 -D__GIMP_PLUGIN_ENABLE__ -D_FILE_OFFSET_BITS=64 -MT libsane_canon_mfp_la-canon_mfp_tools.lo -MD -MP -MF .deps/libsane_canon_mfp_la-canon_mfp_tools.Tpo -c -o libsane_canon_mfp_la-canon_mfp_tools.lo `test -f 'canon_mfp_tools.c' || echo './'`canon_mfp_tools.c libtool: compile: gcc -DHAVE_CONFIG_H -I. -I.. -I. -I./include -DV_MAJOR=2 -DV_MINOR=1 -O2 -D__GIMP_PLUGIN_ENABLE__ -D_FILE_OFFSET_BITS=64 -MT libsane_canon_mfp_la-canon_mfp_tools.lo -MD -MP -MF .deps/libsane_canon_mfp_la-canon_mfp_tools.Tpo -c canon_mfp_tools.c -fPIC -DPIC -o .libs/libsane_canon_mfp_la-canon_mfp_tools.o canon_mfp_tools.c:40:17: fatal error: usb.h: No such file or directory #include ^ compilation terminated. make[2]: *** [libsane_canon_mfp_la-canon_mfp_tools.lo] Error 1 make[2]: Leaving directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp/backend' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/home/psr/Downloads/scangearmp-source-2.10-1/scangearmp' make: *** [all] Error 2 psr@psr-EasyNote-TM85:~/Downloads/scangearmp-source-2.10-1/scangearmp$

  Read the article

• How to resolve "svn: Can't find a temporary directory: Internal error"?

  - by HorusKol

  I have already googled the message, and I have plenty of disk space available on the SVN server (it's about 4% usage of 150 GB). I have noticed that when I try echo $TMPDIR at the command prompt on the SVN server I get nothing. What is making this a little confusing is that I only get this message from one location when I do an svn diff (that I've tested so far) - this error is not coming up when I try from three other computers (one of which is testing against the exact same repository, the other two are different repositories on the same svn server). About the only difference I can see is that the broken working copy is connecting to the server by an IP address where all the others are using a server name (although this resolves over DNS to the same IP Address). I'm hoping that I don't have to scratch the broken working copy and checkout a new one - unfortunately, this is a legacy project and not all changes have been properly revisioned.

  Read the article

• Installing Win7 over PXE through Serva fails on Loading Network Resources

  - by Armand

  Trying to install Win7 OS to a Lenovo E335 with no DVD/CD. I have to do it either over PXE/Network or USB. Although I am able to get passt the installation menu of Serva, it fails on Loading Network Resources ... FAILED No NIC/Driver, ABORTING! This is the only log on the Serva Client PC and nothing on the Serva-server. Would appreciate if someone can tell me how to go pass this error. THe network card works fine, it has already loaded the Windows installation structure on a X: drive on the new laptop. Another detail: I am using a normal Ethernet Cable to connect the PCs. Should this be enough or a crossover cable is a must in this case?

  Read the article

• Debian error : edac mc0 internal error

  - by Xantra

  I have a problem on last Debian Server. I have this error written every seconds on my screen : EDAC MC0: INTERNAL ERROR: csrow value is out of range (7 >= 4) edac-utils give that : mc0: 0 Uncorrected Errors with no DIMM info mc0: 44747 Corrected Errors with no DIMM info mc0: csrow0: 15330 Uncorrected Errors mc0: csrow0: mc#0csrow#0channel#0: 0 Corrected Errors mc0: csrow0: mc#0csrow#2channel#0: 0 Corrected Errors mc0: csrow2: 0 Uncorrected Errors mc0: csrow2: mc#0csrow#1channel#0: 0 Corrected Errors mc0: csrow2: mc#0csrow#3channel#0: 0 Corrected Errors mc0: csrow3: 0 Uncorrected Errors mc0: csrow3: mc#0csrow#1channel#1: 0 Corrected Errors mc0: csrow3: mc#0csrow#3channel#1: 0 Corrected Errors Nothing on Memtest. What's the problem? How to solve it? Thank you.

  Read the article

• C#: System.Collections.Concurrent.ConcurrentQueue vs. Queue

  - by James Michael Hare

  I love new toys, so of course when .NET 4.0 came out I felt like the proverbial kid in the candy store!  Now, some people get all excited about the IDE and it’s new features or about changes to WPF and Silver Light and yes, those are all very fine and grand.  But me, I get all excited about things that tend to affect my life on the backside of development.  That’s why when I heard there were going to be concurrent container implementations in the latest version of .NET I was salivating like Pavlov’s dog at the dinner bell. They seem so simple, really, that one could easily overlook them.  Essentially they are implementations of containers (many that mirror the generic collections, others are new) that have either been optimized with very efficient, limited, or no locking but are still completely thread safe -- and I just had to see what kind of an improvement that would translate into. Since part of my job as a solutions architect here where I work is to help design, develop, and maintain the systems that process tons of requests each second, the thought of extremely efficient thread-safe containers was extremely appealing.  Of course, they also rolled out a whole parallel development framework which I won’t get into in this post but will cover bits and pieces of as time goes by. This time, I was mainly curious as to how well these new concurrent containers would perform compared to areas in our code where we manually synchronize them using lock or some other mechanism.  So I set about to run a processing test with a series of producers and consumers that would be either processing a traditional System.Collections.Generic.Queue or a System.Collection.Concurrent.ConcurrentQueue. Now, I wanted to keep the code as common as possible to make sure that the only variance was the container, so I created a test Producer and a test Consumer.  The test Producer takes an Action<string> delegate which is responsible for taking a string and placing it on whichever queue we’re testing in a thread-safe manner: 1: internal class Producer 2: { 3: public int Iterations { get; set; } 4: public Action<string> ProduceDelegate { get; set; } 5: 6: public void Produce() 7: { 8: for (int i = 0; i < Iterations; i++) 9: { 10: ProduceDelegate(“Hello”); 11: } 12: } 13: } Then likewise, I created a consumer that took a Func<string> that would read from whichever queue we’re testing and return either the string if data exists or null if not.  Then, if the item doesn’t exist, it will do a 10 ms wait before testing again.  Once all the producers are done and join the main thread, a flag will be set in each of the consumers to tell them once the queue is empty they can shut down since no other data is coming: 1: internal class Consumer 2: { 3: public Func<string> ConsumeDelegate { get; set; } 4: public bool HaltWhenEmpty { get; set; } 5: 6: public void Consume() 7: { 8: bool processing = true; 9: 10: while (processing) 11: { 12: string result = ConsumeDelegate(); 13: 14: if(result == null) 15: { 16: if (HaltWhenEmpty) 17: { 18: processing = false; 19: } 20: else 21: { 22: Thread.Sleep(TimeSpan.FromMilliseconds(10)); 23: } 24: } 25: else 26: { 27: DoWork(); // do something non-trivial so consumers lag behind a bit 28: } 29: } 30: } 31: } Okay, now that we’ve done that, we can launch threads of varying numbers using lambdas for each different method of production/consumption.  First let's look at the lambdas for a typical System.Collections.Generics.Queue with locking: 1: // lambda for putting to typical Queue with locking... 2: var productionDelegate = s => 3: { 4: lock (_mutex) 5: { 6: _mutexQueue.Enqueue(s); 7: } 8: }; 9:  10: // and lambda for typical getting from Queue with locking... 11: var consumptionDelegate = () => 12: { 13: lock (_mutex) 14: { 15: if (_mutexQueue.Count > 0) 16: { 17: return _mutexQueue.Dequeue(); 18: } 19: } 20: return null; 21: }; Nothing new or interesting here.  Just typical locks on an internal object instance.  Now let's look at using a ConcurrentQueue from the System.Collections.Concurrent library: 1: // lambda for putting to a ConcurrentQueue, notice it needs no locking! 2: var productionDelegate = s => 3: { 4: _concurrentQueue.Enqueue(s); 5: }; 6:  7: // lambda for getting from a ConcurrentQueue, once again, no locking required. 8: var consumptionDelegate = () => 9: { 10: string s; 11: return _concurrentQueue.TryDequeue(out s) ? s : null; 12: }; So I pass each of these lambdas and the number of producer and consumers threads to launch and take a look at the timing results.  Basically I’m timing from the time all threads start and begin producing/consuming to the time that all threads rejoin.  I won't bore you with the test code, basically it just launches code that creates the producers and consumers and launches them in their own threads, then waits for them all to rejoin.  The following are the timings from the start of all threads to the Join() on all threads completing.  The producers create 10,000,000 items evenly between themselves and then when all producers are done they trigger the consumers to stop once the queue is empty. These are the results in milliseconds from the ordinary Queue with locking: 1: Consumers Producers 1 2 3 Time (ms) 2: ---------- ---------- ------ ------ ------ --------- 3: 1 1 4284 5153 4226 4554.33 4: 10 10 4044 3831 5010 4295.00 5: 100 100 5497 5378 5612 5495.67 6: 1000 1000 24234 25409 27160 25601.00 And the following are the results in milliseconds from the ConcurrentQueue with no locking necessary: 1: Consumers Producers 1 2 3 Time (ms) 2: ---------- ---------- ------ ------ ------ --------- 3: 1 1 3647 3643 3718 3669.33 4: 10 10 2311 2136 2142 2196.33 5: 100 100 2480 2416 2190 2362.00 6: 1000 1000 7289 6897 7061 7082.33 Note that even though obviously 2000 threads is quite extreme, the concurrent queue actually scales really well, whereas the traditional queue with simple locking scales much more poorly. I love the new concurrent collections, they look so much simpler without littering your code with the locking logic, and they perform much better.  All in all, a great new toy to add to your arsenal of multi-threaded processing!

  Read the article

• Postgresql fails to start on Ubuntu 10.04.4 LTS

  - by cancerballs

  I installed postgresql 9.2 from add-apt-repository ppa:pitti/postgresql using apt-get install postgresql-9.2 At the end of the install and every time I try to launch postgresql by using the following command /etc/init.d/postgresql start or service postgresql start I get this error: Error: could not exec /usr/lib/postgresql/9.2/bin/pg_ctl /usr/lib/postgresql/9.2/bin/pg_ctl start -D /var/lib/postgresql/9.2/main -l /var/log/postgresql/postgresql-9.2-main.log -s -o -c config_file="/etc/postgresql/9.2/main/postgresql.conf" : [fail] invoke-rc.d: initscript postgresql, action "start" failed. dpkg: error processing postgresql-9.2 (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: postgresql-9.2 E: Sub-process /usr/bin/dpkg returned an error code (1) I have tried everything found here: How to thoroughly purge and reinstall postgresql on ubuntu and here: Eliminating non working postgresql installations on ubuntu 10-04 and starting af. I have also done dpkg -P --force-remove-reinstreq postgresql-client-9.2 in my attempt to remove everything postgres related from my server. After removing postgresql I have used dpkg --get-selections | grep postg To be sure there is nothing left and I can do a clean install. I have also made sure that the files and folders mentioned in the error message have the right permissions. The /var/log/postgresql/postgresql-9.2-main.log file is empty. I have tried installing every postgresql version from 8.3 to 9.2 and I get the same error on every time. I once managed to compile postgresql from the source provided on their website but then I encountered weird errors with psycopg2 so I figured I'd install postgresql this way and avoid those errors. Also when I type apt-get install postgresql it by default tries to install the 8.3 version even when I can find the package by typing apt-get install postgresql-9.2.

  Read the article

• Import IIS6 website configuration into IIS7

  - by sinni800

  Hello, I have many websites hosted on IIS6 and I want to migrate them to IIS7. It is enough if the basic configuration (folder, virtual folders inside, hostheaders, ) is migrated. a great part of the configuration is in web.config anyway. It is even okay if they're just created as "classic" mode applications. I have tried the following things: Msdeploy. This copies the whole directoried though, not good... Tried exporting the iis websites to xml... Found nothing to give them to iis7... Anybody got an idea?

  Read the article

• Import IIS6 website configuration into IIS7

  - by sinni800

  Hello, I have many websites hosted on IIS6 and I want to migrate them to IIS7. It is enough if the basic configuration (folder, virtual folders inside, hostheaders, ) is migrated. a great part of the configuration is in web.config anyway. It is even okay if they're just created as "classic" mode applications. I have tried the following things: Msdeploy. This copies the whole directoried though, not good... Tried exporting the iis websites to xml... Found nothing to give them to iis7... Anybody got an idea?

  Read the article

• Generate a Strong Password using Mac OS X Lion’s Built-in Utility

  - by Usman

  You might’ve heard of the LinkedIn and last.fm security breaches that took place recently. Not to mention the thousands of websites that have been hacked till now. Nothing is invulnerable to hacking. And when something like that happens, passwords are leaked. Choosing a good password is essential. A good password generator can give you the best blend of alphanumeric and symbolic characters, making up a strong password. There are a variety of password generators out there, but not many people know that there’s one built right into Mac OS X Lion. Read on to see how you can generate a strong password without any third party application. To do this, open System Preferences. Click “Users & Groups”. How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It? HTG Explains: What Is Windows RT and What Does It Mean To Me?

  Read the article

• "Outlook must be online or connected to complete this action" windows XP, outlook 2007, connect to e

  - by bob franklin smith harriet

  Hey, I can't connect to an exchange server using windows XP and outlook 2007, using the "connect anywhere over HTTP" process, it has been working until recently and the user reports no recent changes to his environment. The error is "Outlook must be online or connected to complete this action" It will prompt me for the username and password which I can enter, then it will give the errorm however this only happens when I delete the account and enter all details for the excahnge server again. The client computer that is unable to connect using outlook can connect to the HTTPS mail service and login send/receive fine. Nobody else has reported issues. making a test environment with a clean install of XP and outlook 2007 gives the same error, but using windows 7 and outlook 2007 connects perfectly fine everytime. I also removed all passwords using control keymgr.dll which didnt help. Any assistance or ideas would be appreciated, at this point nothing I've tried from technet or google works <_<

  Read the article

• FIM 2010 GAL MA - It appears this forest is not exchange enabled.

  - by WooYek

  I am trying to configure a Management Agent (MA) for Global Address List (GAL) sync in FIM 2010. I cannot move to the next step from "Configure GAL" because of an error message saying "It appears this forest is not exchange enabled". Nothing I change on "Configure GAL" step is changing this behavior. I'am configuring a standalone test lab. I have a Windows 2008 R2 x64 Server, promoted to a DC and SQL 2008 SP1 installed, DNS is also running locally. I have tried to install Exchange 2010 and 2007, but there is no difference. AD MA works fine. Any ideas what did I screw up?

  Read the article

• "No video with supported format and mime type found" - Firefox - HTML5

  - by mangobug

  I am working with django 1.6, python 2.7, firefox 30 and Mac OS 10.10 Beta. When I render the following code <video width="570" height="340" controls="controls"> <source src="/some/path/" type="video/mp4" /> </video> I get an error stating "No video with supported format and mime type found". The same code runs perfectly on Safari and Chrome (yes I still haven't checked IE). I have tried different formats for the uploaded files and looked into ad-ons which might prevent this or different coding mechanisms, though nothing has been helpful. Please help!!!!

  Read the article

• Cannot start serial over lan on iDrac6

  - by Bryan Agee

  I have a couple of Dell R610/R710 servers loaded with iDrac6 system management boards. I figured out how to log into the SM CLP with ssh. According to the dell documentation, I should be able to start a console session by running: start /system1/sol1 but I get the following failure message: cmdstat status : 3 status_tag : COMMAND EXECUTION FAILED job job_id : 12 joberr errtype : 1 errtype_desc : Other cimstat : 6 cimstat_desc : CIM_ERR_NOT_FOUND severity : 2 severity_desc : Low /system1/sol1 started FAILED at Sun Sep 16 00:20:58 2012 I have enabled the serial-over-lan via the web interface and rebooted, but nothing seems to make them available.

  Read the article

• Why do programmers use or recommend Mac OS X?

  - by codingbear

  I've worked on both Mac and Windows for awhile. However, I'm still having a hard time understanding why programmers enthusiastically choose Mac OS X over Windows and Linux? I know that there are programmers who prefer Windows and Linux, but I'm asking the programmers who would just use Mac OS X and nothing else, because they think Mac OS X is the greatest fit for programmers. Some might argue that Mac OS X got the beautiful UI and is nix based, but Linux can do that. Although Windows is not nix based, you can pretty much develop on any platform or language, except Cocoa/Objective-C. Is it the softwares that offer only on Mac OS X? Does that really worth using Mac? Is it to develop iPhone apps? Is it because you need to buy new Windows every 2 years (less backwards compatible)? I understand why people, who are working in multimedia/entertainment industry, would use Mac OS X; however, I don't have strong merits of Mac OS X over Windows. If you develop daily on Mac and prefer Mac over anything else, can you give me a merit that Mac has over Windows/Linux? Maybe something you can do on Mac that cannot be done in Windows/Linux with the same level of ease? I'm not trying to do another Mac vs. Windows here. I tried to find things that I do on Mac that cannot be done on Windows with the same level of ease, but I couldn't. So, I'm asking for some help.

  Read the article

• Upgrading Sharepoint MOSS 2007 Farm to Sharepoint 2010 "waiting to get a lock to upgrade the farm"

  - by Wes Weeks

  My first inplace upgrade of a MOSS 2007 farm to sharepoint went pretty smooth. I read the preupgrade documentation and was comfortable with the steps.  Since it was a fairly new installation of Moss changes were minimal and I wasn't anticipating too many problems The one issue I got was after installing the software on all of the farm.  I went to the first machine which ran Sharepoint 2010 central administration and ran the Sharepoint 2010 Products Configuration Wizard.  I received the message that I would need to run the configuration on each server in the farm.  Fair enough, I expected as much. The wizard completed without issue on the first server, but when I tried to run it on the others it hung with a "waiting to get a lock to upgrade the farm" message.  It hung for about 10 minutes and then the wizard failed.  Did a few searches on Google and Bing and got 0 results for that message.  None, Nothing, Zilch.  I'm on my own... For grins, hit the help button on the configuration wizard and it seemed to indicate that the configuration wizard needed to be run on all farm servers simultaneously.  I started it again on the first server to the point I got the message about needing to be run on all servers on the farm and then started the wizard on the other servers and ran it to that point as well.  I then clicked ok on the first server and then the subsuquent servers. It took a while and it did hang on the lock message for some time, but then it did kick off and completed succesfully on all of them.  Yeah! Hope this helps someone else!  Now there should be at least one post with this error message on it!

  Read the article

• 401 - Unauthorized On Server 2008 R2 IIS 7.5

  - by mxmissile

  I have a web application deployed to Server 2008 IIS 7.5 box. From remote it gives this error: 401 - Unauthorized: Access is denied due to invalid credentials. (remote = desktops on the same LAN) Have tried several remote clients using different browsers, all the same result. (IE, FF, and Chrome) Hitting the application from the desktop of the server itself works flawlessly. The application is using Anonymous Authentication. The application is written in .NET 4.0 Asp.Net using the MVC framework. Sysinternals procmon returns these 2 results for each request: FAST IO DISALLOWED and PATH NOT FOUND. I have 2 other MVC apps running fine on the same server. I have checked the security on the folders and they all match. App runs fine on a Server 2008 IIS 7.0 box. Nothing shows up in the Event log on the server related to this. Pulling my hair out here, any troubleshooting tips?

  Read the article

• sshfs with fstab: connection reset by peer

  - by user171348

  I am trying to allow my laptop (Ubuntu 13.04) to access my PC (Lubuntu 13.04) hard drive through SSHFS. I'm using RSA keys to connect. It works perfectly fine if I type this in the terminal: sshfs my-PC:/a_folder /media/a_folder But I would like it to be mounted automatically when I boot my laptop. So I added myself to the fuse group: sudo adduser mynickname fuse And I added the following line to my fstab file: sshfs#mynickname@my-PC:/a_folder /media/a_folder fuse defaults,idmap=user,_netdev 0 0 When I boot the laptop, a_folder appears in the list of devices, but is not mounted. When I try to access it through Nautilus, it displays the following error: mount: only root can mount sshfs#mynickname@my-PC:/a_folder on /media/a_folder I get the same error if I try mount /media/a_folder in a terminal. If I try sudo mount /media/a_folder I get read: Connection reset by peer I tried to add "allow_other" as an option in the fstab entry, and uncommented the related line in /etc/fuse.conf, but it didn't change anything. The user "mynickname" is the owner of the folder /media/a_folder and has rwx permissions. I looked at many threads on the internet about people with quite similar issues, but nothing worked so far. Usually, people can't even do sshfs my-PC:/a_folder /media/a_folder without getting an error, whereas this works fine on my laptop. Any insight and tips will be greatly appreciated! Thanks.

  Read the article

• Setting Up GLFW3 in Visual Studio

  - by sm81095

  I decided a couple of days ago that I was going to start trying to develop games in C++ with OpenGL, instead of C# Monogame like I have been doing for a while. I was looking around for libraries to use, to make OpenGL a little easier to use. I settled on GLEW and GLFW. GLEW was a super easy copy/paste, but GLFW3 was not. After looking around for a while and fighting with CMake, I got the GLFW2.lib file created, and I added the additional include directories, library directories, and linked my program to the glfw3.lib file I just created. The problem is, I get these linker errors when I try to run or build my program: Error 1 error LNK2019: unresolved external symbol _glfwInit referenced in function _main C:\Codex Interactive\Projects\OGLTest\OGLTest\test.obj OGLTest Error 2 error LNK2019: unresolved external symbol _glfwTerminate referenced in function _main C:\Codex Interactive\Projects\OGLTest\OGLTest\test.obj OGLTest Error 3 error LNK2019: unresolved external symbol _glfwSetErrorCallback referenced in function _main C:\Codex Interactive\Projects\OGLTest\OGLTest\test.obj OGLTest and 10 other LNK2019 errors, all talking about some glfw method, as well as: Error 14 error LNK1120: 13 unresolved externals C:\Codex Interactive\Projects\OGLTest\Debug\OGLTest.exe 1 1 OGLTest at the very bottom of the error list. I've looked up most of these errors on their own, and the solutions that I find either do nothing to solve the problem, or are people commenting on how dumb people are for not being about to solve this linker problem. Any assistance to solve these errors would be greatly appreciated. Info: I built GLFW3 on Cmake for Visual Studio 11, 32 bit and 64 bit, and both threw the same errors. The only extra libraries I linked were opengl32.lib, glu32.lib, and glfw3.lib Here is the test code (from GLFW3's latest tutorial): Code

  Read the article

• mount: cannot remount block device /dev/sda5 read-write, is write-protected

  - by marc.riera

  So, this is it. Everything is working as usual except the disk is read only and dont want to change back. ^_^! thanks. root@NODE02:/tmp# df . Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda5 461490504 179502128 258545928 41% / root@NODE02:/tmp# mount -o rw,remount /dev/sda5 mount: cannot remount block device /dev/sda5 read-write, is write-protected root@NODE02:/tmp# touch helll touch: cannot touch `helll': Read-only file system It's not multipath. It's nothing special. Just a server with ubuntu 9.10. makes no sense for me, does it?

  Read the article

• jQuery Templates and Data Linking (and Microsoft contributing to jQuery)

  - by ScottGu

  The jQuery library has a passionate community of developers, and it is now the most widely used JavaScript library on the web today. Two years ago I announced that Microsoft would begin offering product support for jQuery, and that we’d be including it in new versions of Visual Studio going forward. By default, when you create new ASP.NET Web Forms and ASP.NET MVC projects with VS 2010 you’ll find jQuery automatically added to your project. A few weeks ago during my second keynote at the MIX 2010 conference I announced that Microsoft would also begin contributing to the jQuery project.  During the talk, John Resig -- the creator of the jQuery library and leader of the jQuery developer team – talked a little about our participation and discussed an early prototype of a new client templating API for jQuery. In this blog post, I’m going to talk a little about how my team is starting to contribute to the jQuery project, and discuss some of the specific features that we are working on such as client-side templating and data linking (data-binding). Contributing to jQuery jQuery has a fantastic developer community, and a very open way to propose suggestions and make contributions.  Microsoft is following the same process to contribute to jQuery as any other member of the community. As an example, when working with the jQuery community to improve support for templating to jQuery my team followed the following steps: We created a proposal for templating and posted the proposal to the jQuery developer forum (http://forum.jquery.com/topic/jquery-templates-proposal and http://forum.jquery.com/topic/templating-syntax ). After receiving feedback on the forums, the jQuery team created a prototype for templating and posted the prototype at the Github code repository (http://github.com/jquery/jquery-tmpl ). We iterated on the prototype, creating a new fork on Github of the templating prototype, to suggest design improvements. Several other members of the community also provided design feedback by forking the templating code. There has been an amazing amount of participation by the jQuery community in response to the original templating proposal (over 100 posts in the jQuery forum), and the design of the templating proposal has evolved significantly based on community feedback. The jQuery team is the ultimate determiner on what happens with the templating proposal – they might include it in jQuery core, or make it an official plugin, or reject it entirely.  My team is excited to be able to participate in the open source process, and make suggestions and contributions the same way as any other member of the community. jQuery Template Support Client-side templates enable jQuery developers to easily generate and render HTML UI on the client.  Templates support a simple syntax that enables either developers or designers to declaratively specify the HTML they want to generate.  Developers can then programmatically invoke the templates on the client, and pass JavaScript objects to them to make the content rendered completely data driven.  These JavaScript objects can optionally be based on data retrieved from a server. Because the jQuery templating proposal is still evolving in response to community feedback, the final version might look very different than the version below. This blog post gives you a sense of how you can try out and use templating as it exists today (you can download the prototype by the jQuery core team at http://github.com/jquery/jquery-tmpl or the latest submission from my team at http://github.com/nje/jquery-tmpl).  jQuery Client Templates You create client-side jQuery templates by embedding content within a <script type="text/html"> tag.  For example, the HTML below contains a <div> template container, as well as a client-side jQuery “contactTemplate” template (within the <script type="text/html"> element) that can be used to dynamically display a list of contacts: The {{= name }} and {{= phone }} expressions are used within the contact template above to display the names and phone numbers of “contact” objects passed to the template. We can use the template to display either an array of JavaScript objects or a single object. The JavaScript code below demonstrates how you can render a JavaScript array of “contact” object using the above template. The render() method renders the data into a string and appends the string to the “contactContainer” DIV element: When the page is loaded, the list of contacts is rendered by the template.  All of this template rendering is happening on the client-side within the browser:   Templating Commands and Conditional Display Logic The current templating proposal supports a small set of template commands - including if, else, and each statements. The number of template commands was deliberately kept small to encourage people to place more complicated logic outside of their templates. Even this small set of template commands is very useful though. Imagine, for example, that each contact can have zero or more phone numbers. The contacts could be represented by the JavaScript array below: The template below demonstrates how you can use the if and each template commands to conditionally display and loop the phone numbers for each contact: If a contact has one or more phone numbers then each of the phone numbers is displayed by iterating through the phone numbers with the each template command: The jQuery team designed the template commands so that they are extensible. If you have a need for a new template command then you can easily add new template commands to the default set of commands. Support for Client Data-Linking The ASP.NET team recently submitted another proposal and prototype to the jQuery forums (http://forum.jquery.com/topic/proposal-for-adding-data-linking-to-jquery). This proposal describes a new feature named data linking. Data Linking enables you to link a property of one object to a property of another object - so that when one property changes the other property changes.  Data linking enables you to easily keep your UI and data objects synchronized within a page. If you are familiar with the concept of data-binding then you will be familiar with data linking (in the proposal, we call the feature data linking because jQuery already includes a bind() method that has nothing to do with data-binding). Imagine, for example, that you have a page with the following HTML <input> elements: The following JavaScript code links the two INPUT elements above to the properties of a JavaScript “contact” object that has a “name” and “phone” property: When you execute this code, the value of the first INPUT element (#name) is set to the value of the contact name property, and the value of the second INPUT element (#phone) is set to the value of the contact phone property. The properties of the contact object and the properties of the INPUT elements are also linked – so that changes to one are also reflected in the other. Because the contact object is linked to the INPUT element, when you request the page, the values of the contact properties are displayed: More interesting, the values of the linked INPUT elements will change automatically whenever you update the properties of the contact object they are linked to. For example, we could programmatically modify the properties of the “contact” object using the jQuery attr() method like below: Because our two INPUT elements are linked to the “contact” object, the INPUT element values will be updated automatically (without us having to write any code to modify the UI elements): Note that we updated the contact object above using the jQuery attr() method. In order for data linking to work, you must use jQuery methods to modify the property values. Two Way Linking The linkBoth() method enables two-way data linking. The contact object and INPUT elements are linked in both directions. When you modify the value of the INPUT element, the contact object is also updated automatically. For example, the following code adds a client-side JavaScript click handler to an HTML button element. When you click the button, the property values of the contact object are displayed using an alert() dialog: The following demonstrates what happens when you change the value of the Name INPUT element and click the Save button. Notice that the name property of the “contact” object that the INPUT element was linked to was updated automatically: The above example is obviously trivially simple.  Instead of displaying the new values of the contact object with a JavaScript alert, you can imagine instead calling a web-service to save the object to a database. The benefit of data linking is that it enables you to focus on your data and frees you from the mechanics of keeping your UI and data in sync. Converters The current data linking proposal also supports a feature called converters. A converter enables you to easily convert the value of a property during data linking. For example, imagine that you want to represent phone numbers in a standard way with the “contact” object phone property. In particular, you don’t want to include special characters such as ()- in the phone number - instead you only want digits and nothing else. In that case, you can wire-up a converter to convert the value of an INPUT element into this format using the code below: Notice above how a converter function is being passed to the linkFrom() method used to link the phone property of the “contact” object with the value of the phone INPUT element. This convertor function strips any non-numeric characters from the INPUT element before updating the phone property.  Now, if you enter the phone number (206) 555-9999 into the phone input field then the value 2065559999 is assigned to the phone property of the contact object: You can also use a converter in the opposite direction also. For example, you can apply a standard phone format string when displaying a phone number from a phone property. Combining Templating and Data Linking Our goal in submitting these two proposals for templating and data linking is to make it easier to work with data when building websites and applications with jQuery. Templating makes it easier to display a list of database records retrieved from a database through an Ajax call. Data linking makes it easier to keep the data and user interface in sync for update scenarios. Currently, we are working on an extension of the data linking proposal to support declarative data linking. We want to make it easy to take advantage of data linking when using a template to display data. For example, imagine that you are using the following template to display an array of product objects: Notice the {{link name}} and {{link price}} expressions. These expressions enable declarative data linking between the SPAN elements and properties of the product objects. The current jQuery templating prototype supports extending its syntax with custom template commands. In this case, we are extending the default templating syntax with a custom template command named “link”. The benefit of using data linking with the above template is that the SPAN elements will be automatically updated whenever the underlying “product” data is updated.  Declarative data linking also makes it easier to create edit and insert forms. For example, you could create a form for editing a product by using declarative data linking like this: Whenever you change the value of the INPUT elements in a template that uses declarative data linking, the underlying JavaScript data object is automatically updated. Instead of needing to write code to scrape the HTML form to get updated values, you can instead work with the underlying data directly – making your client-side code much cleaner and simpler. Downloading Working Code Examples of the Above Scenarios You can download this .zip file to get with working code examples of the above scenarios.  The .zip file includes 4 static HTML page: Listing1_Templating.htm – Illustrates basic templating. Listing2_TemplatingConditionals.htm – Illustrates templating with the use of the if and each template commands. Listing3_DataLinking.htm – Illustrates data linking. Listing4_Converters.htm – Illustrates using a converter with data linking. You can un-zip the file to the file-system and then run each page to see the concepts in action. Summary We are excited to be able to begin participating within the open-source jQuery project.  We’ve received lots of encouraging feedback in response to our first two proposals, and we will continue to actively contribute going forward.  These features will hopefully make it easier for all developers (including ASP.NET developers) to build great Ajax applications. Hope this helps, Scott P.S. [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu]

  Read the article

• Ask How-To Geek: Dropbox in the Start Menu, Understanding Symlinks, and Ripping TV Series DVDs

  - by Jason Fitzpatrick

  This week we take a look at how to incorporate Dropbox into your Windows Start Menu, understanding and using symbolic links, and how to rip your TV series DVDs right to unique and high-quality episode files. Once a week we dip into our reader mailbag and help readers solve their problems, sharing the useful solutions with you in the process. Read on to see our fixes for this week’s reader dilemmas. Add Drobox to Your Start Menu Dear How-To Geek, I use Dropbox all the time and would like to add it right onto my start menu along side the other major shortcuts like Documents, Pictures, etc. It seems like adding Dropbox into the menu should be part of the Dropbox installation package! Sincerely, Dropboxing in Des Moines Dear Dropboxing, We agree, it would be a nice installation option. As it stands you’re going to have to do a little simple hacking to get Dropbox nestled neatly into your start menu. The hack isn’t super elegant but when you’re done you’ll have the link you want and it’ll look like it was there all along. Check out this step-by-step guide here in order to take an existing Library shortcut and rework it to be a Dropbox link. Understanding and Using Symbolic Links Dear How-To Geek, I was talking to a coworker the other day about an issue I’d been having with a media center application I’m running. He suggested using symbolic links to better organize my media and make it easier for the application to access my collection. I had no idea what he was talking about and never got a chance to bug him about it later. Can you clear up this whole symbolic links business for me? I’ve been using computers for years and I’ve never even heard of it! Sincerely, Symbolic Who? Dear Symbolic, Symbolic links aren’t commonly used by many Windows users which is why you likely haven’t run into the concept. Symbolic links are essentially supercharged shortcuts—the newly introduced Windows library system is really just a type of symbolic link system. You can use symbolic links to do all sorts of neat stuff like link folders to your Dropbox folder, organize media, and more. The concept of symbolic links is pretty simple but the execution can be really tricky. We’d suggest reading over our guide to creating symbolic links in Windows 7, Windows XP, and Ubunutu to get a clearer idea what you’re getting into. Rip Your TV DVDs into Handy Episode Files Dear How-To Geek, My wife got me an iPod for Christmas and I still haven’t got around to filling it up. I have tons of entire TV show seasons on DVD and would like to get them on the iPod but I have absolutely no idea where to start. How do I get the shows off the discs? I thought it would be as easy to import the TV shows into iTunes as it is to import tracks off a CD but I was totally wrong. I tried downloading some applications to rip them but those didn’t work at all. Very frustrating! Surely there is an easy and/or automated way to do this, right? Sincerely, Free My DVDs Dear DVDs, Oh man is this a frustration we can relate to. It’s inordinately difficult to get movies and TV shows off physical media and into digital (and portable media player-friendly) formats. There are a multitude of ways to rip DVDs and quite a few applications out there (some good, some mediocre, and some outright malware). We’d recommend a two-part punch to solve your ripping woes. You’ll need a copy of DVDFab to strip away the protections on the discs and rip the disc and Handbrake to load the disc image and convert the files. It’s not quite as smooth as the CD-to-iTunes workflow but it’s still pretty easy. Check out all the steps and settings you’ll want to toggle here. Have a question you want to put before the How-To Geek staff? Shoot us an email at [email protected] and then keep an eye out for a solution in the Ask How-To Geek column. Latest Features How-To Geek ETC Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Stop Believing TV’s Lies: The Real Truth About "Enhancing" Images The How-To Geek Valentine’s Day Gift Guide Inspire Geek Love with These Hilarious Geek Valentines Google’s New Personal Blocklist Extension Kills Search Engine Spam KeyCounter Tracks Your Keystrokes and Mouse Clicks Add Custom LED Ambient Lighting to Your PC or Media Center The Trackor Monitors Amazon Prices; Integrates with Chrome, Firefox, and Safari Four Awesome TRON Legacy Themes for Chrome and Iron Anger is Illogical – Old School Style Instructional Video [Star Trek Mashup]

  Read the article

< Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >