Search Results

Search found 10674 results on 427 pages for 'glib config'.

Page 329/427 | < Previous Page | 325 326 327 328 329 330 331 332 333 334 335 336  | Next Page >

  • Apache Proxy and Rewrite, append directory to URL

    - by ionFish
    I have a backend server running on http://10.0.2.20/ from the local network, which serves similar to this: / (root) | |_user1/ | |_www/ | |_private/ | |_user2/ |_www/ |_private/ (etc.) Accessing http://10.0.2.20/user1/ of course, contains 'www' and 'private' folders and is proxied through a public server using Apache's Reverse Proxy. I'd like it so the following happens: http://public-proxy-server/user1/ actually shows the content from http://10.0.2.20/user1/www/ without indicating it in the URL. (/private/ would not be accessible via the public proxy server). The key here, is for it to be dynamic, so all requests to http://public-proxy-server/*/should show content from http://10.0.2.20/*/www/. Again, the proxy currently works fine; below is the config: (On the public server) <VirtualHost *:80> ServerName www.domain.com ProxyRequests Off ProxyPreserveHost On ProxyVia full ProxyPass / http://10.0.2.20/ ProxyPassReverse / http://10.0.2.20/ </VirtualHost> (On the backend server) <VirtualHost *:80> ... #this directory contains folders 'user1' and 'user2' DocumentRoot /var/www/ ... </VirtualHost>

    Read the article

  • TFTP Timing Out on Ubuntu VM

    - by valsidalv
    I'm running a Windows 7 PC with VMware installed which has my Ubuntu (10.04 Lucid Lynx). I recently installed a DHCP server and TFTP (Xinet tftpd) using these instructions. I've mapped a network drive so that my Windows has access to all the files in my VM through a 192.x.x.x IP address. I'm trying to throw some custom firmware onto a router. The router has its own built-in TFTP utility that will download the image. It successfully manages to do everything but it is slow because it writes it to flash memory. There is another method that is much quicker because it writes to RAM directly but it must use the TFTP server in Ubuntu. The issue I'm facing is that the Ubuntu TFTP transfer seems to be timing out. The transfer starts but never goes past ~60%. Here's my /etc/xinetd.d/tftp file (similar to a known working config): service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /home/user/tftp/ disable = no cps = 300 2 per_source = 60 } I've done some searching but can't find any parameters for this file to control timeout time or number of retries. The last two arguments (cps, per_source) and completely alien to me (can anyone explain). I have a few possible solutions but the easiest would be to get this TFTP server working. Can anyone help? Either with a timeout configuration or maybe even recommend a different TFTP server? Thanks!

    Read the article

  • iptables to block non-VPN-traffic if not through tun0

    - by dacrow
    I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

    Read the article

  • memory tuning with rails/unicorn running on ubuntu

    - by user970193
    I am running unicorn on Ubuntu 11, Rails 3.0, and Ruby 1.8.7. It is an 8 core ec2 box, and I am running 15 workers. CPU never seems to get pinned, and I seem to be handling requests pretty nicely. My question concerns memory usage, and what concerns I should have with what I am seeing. (if any) Here is the scenario: Under constant load (about 15 reqs/sec coming in from nginx), over the course of an hour, each server in the 3 server cluster loses about 100MB / hour. This is a linear slope for about 6 hours, then it appears to level out, but still maybe appear to lose about 10MB/hour. If I drop my page caches using the linux command echo 1 /proc/sys/vm/drop_caches, the available free memory shoots back up to what it was when I started the unicorns, and the memory loss pattern begins again over the hours. Before: total used free shared buffers cached Mem: 7130244 5005376 2124868 0 113628 422856 -/+ buffers/cache: 4468892 2661352 Swap: 33554428 0 33554428 After: total used free shared buffers cached Mem: 7130244 4467144 2663100 0 228 11172 -/+ buffers/cache: 4455744 2674500 Swap: 33554428 0 33554428 My Ruby code does use memoizations and I'm assuming Ruby/Rails/Unicorn is keeping its own caches... what I'm wondering is should I be worried about this behaviour? FWIW, my Unicorn config: worker_processes 15 listen "#{CAPISTRANO_ROOT}/shared/pids/unicorn_socket", :backlog = 1024 listen 8080, :tcp_nopush = true timeout 180 pid "#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid" GC.respond_to?(:copy_on_write_friendly=) and GC.copy_on_write_friendly = true before_fork do |server, worker| STDERR.puts "XXXXXXXXXXXXXXXXXXX BEFORE FORK" print_gemfile_location defined?(ActiveRecord::Base) and ActiveRecord::Base.connection.disconnect! defined?(Resque) and Resque.redis.client.disconnect old_pid = "#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid.oldbin" if File.exists?(old_pid) && server.pid != old_pid begin Process.kill("QUIT", File.read(old_pid).to_i) rescue Errno::ENOENT, Errno::ESRCH # already killed end end File.open("#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid.ok", "w"){|f| f.print($$.to_s)} end after_fork do |server, worker| defined?(ActiveRecord::Base) and ActiveRecord::Base.establish_connection defined?(Resque) and Resque.redis.client.connect end Is there a need to experiment enforcing more stringent garbage collection using OobGC (http://unicorn.bogomips.org/Unicorn/OobGC.html)? Or is this just normal behaviour, and when/as the system needs more memory, it will empty the caches by itself, without me manually running that cache command? Basically, is this normal, expected behaviour? tia

    Read the article

  • Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

    - by jimp
    I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

    Read the article

  • Windows Server 2008 R2 Finding Hidden files that are causing drive to fill up

    - by Xaxum
    What is the best way to find out what files are sucking up so much space? My Windows directory lists its size as 15 GB but when I run a powershell script against it, it shows 40 GB. It seems 40 GB is about right because if I use that 40 GB and add it to the rest of my folders on C I get the 45 GB that is in use. I checked volume shadow copy and that is disabled and there are no volume shadow files listed. My page file is limited to 3 GB. How can I find out what files are taking 25 GB of space? Final Results: We ended up disabling UAC and then the Properties showed the true file size of the Windows folder, as shown in powershell script. This allowed us to drill down to the folder that had the issues... In our case it was in C:\Windows\System32\config\systemprofile\AppData\Local\VMware\VDM there were several large dump files, these were the mysterious unknown files in WinDirStat. It turns out our nessus scan is crashing a view service for a couple seconds so it creates a large dump file. So we will try this.. https://discussions.nessus.org/thread/5212

    Read the article

  • How do I change the Dropbox directory on a headless GNU/Linux server?

    - by DrTwox
    I have installed Dropbox 2.0.0 via command line on my home server (Ubuntu Server 12.04) to use for off-site automated backups, but I can't change the directory that the Dropbox daemon keeps synced. I've tried the following: The official docs say to use the desktop application, which is not applicable in my situation. However I installed the desktop app on my desktop machine and changed the default folder location, but I can't find where this change is stored in the ~/.dropbox/ directory so I can make the same change on the server. This page (and several others) recommends a Python script to do the job. Looking at the script, it opens a SQLite database called ~/.dropbox/dropbox.db, which does not exist on my Dropbox install, leading me to believe the script is out-of-date. This forum thread suggests manually inserting the required row in the config.db database, which I did, but it made no difference. I checked the same database file on my desktop machine, and it does not have the dropbox_path key, so I'm presuming the information in that thread is also out of date for version 2.0. I have tried to launch the Dropbox GUI configuration wizard over SSH with X11 forwarding, as suggested in one of the answers, but the binary must detect the absence of a local X11 install and it starts a command line daemon instead, which provides no means to change the option I need. I am currently using a symlink, as suggested as an answer, but this is a kludge. I would like to know the correct way to make the change. How do I change the Dropbox directory on a headless GNU/Linux server? Update: I've ditched Dropbox and started using Copy. Their Linux tools and support is far superior to Dropbox. I leave this question here in case someone, someday, can answer it.

    Read the article

  • OpenSWAN KLIPS not working

    - by bonzi
    I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

    Read the article

  • Apache going straight to 100% mem usage on localhost

    - by Dennis Pedrie
    Hi, I'm running XAMPP on a OS X testing server... I'm the only person sending requests to the server. I've never messed with Apache config before, so I'm kinda without a paddle here. When I start Apache, I get ~10 httpd processes started, and 95% idle CPU. When I request a WordPress page, the CPU usage goes to 50%, and the page loads in about five seconds. It seems like once the page has finished loading, the CPU usage jumps to 100%, almost all of that httpd. A ton of processes get started, and they don't go away, and their CPU usage stays the same. I've changed the MaxRequestPerChild setting and so forth, but nothing seems to solve the problem. Even now, having not send any requests for about 15 minutes, the CPU usage is at 100%. Here's the applicable settings: Timeout 10 KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 3 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 0 MaxSpareServers 2 MaxClients 20 MaxRequestsPerChild 50 </IfModule> I had always thought that once the request was made, Apache killed the process. Is there anything I can do to bring down the CPU usage, or is this just something I'll have to deal with? Thanks for helping out an Apache idiot.

    Read the article

  • MacOS creates a new mount on AFP path calls

    - by jAndy
    Hi Folks, following scenario: In my webapp, my customers are using Firefox as target browser. They have the need to open afp:// folders via Javascript. To make a long story short, this really works. You need to setup Firefox with about:config and set the value network.protocol-handler.external.afp to true. What happens then, the operating system (OSX) takes care of that path and it correctly opens a Finder window. The problem: OSX does create a new mount every time. It cannot distinct between afp://host/path/111 and afp://host/path/222 for instance. Furthermore, even if the afp path is 100% identical a new mount is created. It looks like this is the default behavior from OSX regardless of Firefox. So, is there any chance I can tell OSX not to create a new mount for some sub directorys which should get access over afp:// ? update: It looks like, there are OSX applications which can change the default behavior for network protocols. So you can change "somewhere" which application OSX should call for a protocol. If that is true, wouldn't it be possible to create a script which just opens the local path without a afp:// prefix ? The question here is, where is that configuration (?) to tell OSX which application to use for specific protocol. Any help welcome!

    Read the article

  • IIS crashes with unhandled exception in ASP.NET

    - by SnowCrash
    We had an issue recently with an unhandled exception in an ASP.NET C# application bringing down IIS and all application pools that it was hosting. IIS Manager was unable to restart or stop/start the service and I was unable start IIS again after killing w3wp.exe in the task manager. A system reboot restored IIS to a running state; as a primarily Linux admin, I generally consider an unplanned system reboot to resolve a software error to be an act of high heresy. Is there a way to "harden" IIS so that a faulting application does not affect anything but the request that exposes the fault? Some details on the server and application fault. IIS: 7.5 .NET: 4.0 Windows Server 2008 R2 Faulted on call to System.Net.Dns.Resolve() with a url pointing to a non-existant domain as the argument. (I'm aware that this method is deprecated but the point that a page code issue shouldn't bring down the server still stands) The exception generated was SocketException. The faulting module according to event viewer was KERNELBASE.dll The issue was resolved by wrapping the call in a try-catch, logging the exception and displaying some generic content on the page. I'm hoping that I missed something in the IIS config that would switch it to "production" mode or something.

    Read the article

  • A lots of Apache processes are using my CPU uses always more than 70%

    - by Barkat Ullah
    I am running a plesk panel in 1and1. I have 120 sites running and all are using pligg cms, each site has 600 visitors per day. Please see the details of my server below: HDD-1000GB RAM-16GB Processor-6 Core I always see a lot of apache processes running in my # top view, so the server seems overloaded. If I can reduce the amount apache processes I think the server will be ok. But I don't know why too many apache processes are running. Please see the link below for the screenshot of my # top view: http://dl.dropbox.com/u/26967109/%23Top-2.jpg Sometimes I saw too many connection error in my plesk control panel, so I added the below line in my [mysqld] section: set-variable=max_connections=416 But I didn't find a solution yet. I have also added maxclients and serverlimit 416 in the config /etc/httpd/conf/httpd.conf But no solution yet. I am researching around more than 7 days but don't get any solution. Please help me to solve the problem. In peak hours my sites are taking too much time to load, but off-peak hour it is ok. Please help me to find out the actual problem.

    Read the article

  • Amazon EC2 Nat Instance - goes out but not back in

    - by nocode
    I've followed Amazon's steps and list what I've done. I've created 6 subnets (4 private SN1: 10.50.1.0/24, SN2: 10.50.2.0/24, SN3: 10.50.3.0/24, SN4: 10.50.4.0/24) and 2 public (SN5: 10.50.101.0/24 and SN6: 10.50.102.0/24) -I have a Bastion host and a NAT instance on SN5 and assigned EIP's to both. I created a test instance on SN1. edit: -NAT instance has source/destination check disabled -On the NAT instance, I had enabled the following commands to be bootstrapped: echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -s 10.0.0.0/16 -j MASQUERADE -In my VPC, the private subnets have their own route table and configured 0.0.0.0/0 to the NAT instance with 4 subnets being associated with the route table. I have a second route table for my public subnets and 0.0.0.0/16 is pointed towards the IGW (with the other 2 subnets associated with it). -For Security Groups, I have the NAT instance accepting all traffic on each of the 4 subnets and all OUTBOUND traffic is allowed. For my test server, I have allowed all outbound access and have allowed all traffic from the public subnet of the NAT host. I can ping internally with no issues. On my test instance, if I try to ping google.com, DNS resolves however I don't get a reply back. On my NAT instance, I run a tcpdump and can see the request being requested to google.com but it's not sending the reply back. My NAT host can ping and receive a reply from google. From the test host, when I ping the NAT instance, the tcpdump shows a request and receive. Is there something I'm missing? EDIT: I've figured it out - I had to save the iptable config and restart the service.

    Read the article

  • Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

    - by Jander
    I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

    Read the article

  • Setting the default permissions for files uploaded via FTP to a directory

    - by Kerri
    Disclaimer: I'm just a web designer/coder, and server admin stuff is my weakest point of them all. So be easy on me (and very specific). I'm using a simple CMS (Unify) on a site, where part of the functionality is that the client can upload files to a specified directory (using FTP). The permissions for the upload directory are set to 755. But when files are uploaded through the interface, they are uploaded with permissions set to 640 (instead of 644), so site visitors cannot acces the files. When I emailed the CMS's support about this, they told me that it was a server setting, and I need to make sure that files uploaded through FTP are set to 644. Makes perfect sense, but I have no idea how to do this. Any help would be greatly appreciated. This site is a shared site hosted by Network Solutions (Unix), so my access options are limited. I can edit .htaccess files, and php.ini, but that's about all I have access to. It appears I can't even log on via shell. ETA: 11/11/2010 Thanks all. I was able to work around this problem by setting up the CMS's settings in a different way. I'd be interested in following up on Nick O'Niel's suggestions, because I think he's on the right track, but unfortunately I can't access the necessary files on this particular server. So, anyway, I'm leaving this open, since the original questions isn't exactly resolved. Unfortunately, I probably can't put a correct answer to the test, since the shared server in question has nearly all of its config files tightly locked down.

    Read the article

  • Service nginx reload: unexpected error

    - by Anna
    I'm trying to install wordpress on my nginx server by following this tutorial: http://premium.wpmudev.org/blog/how-to-setup-your-own-nginx-powered-wordpress-server/ However, the last command at step 7 gave me a strange error: service nginx reload A copy-paste from my terminal: root@server:~# service nginx reload Reloading nginx configuration: nginx: [emerg] unexpected "o" in /etc/nginx/sites-enabled/wordpress:7 nginx: configuration file /etc/nginx/nginx.conf test failed When I nano into sites-enabled/wordpress, on the 7th line I can't find anything strange: <!DOCTYPE html> <html class=" "> <head prefix="og: http://ogp.me/ns# fb: http://ogp.me/ns/fb# object: http://ogp.me/ns/object# article: http://ogp.me/ns/article# profile: http://ogp.me/ns/profile#"> <meta charset='utf-8'> <meta http-equiv="X-UA-Compatible" content="IE=edge"> Also, I don't see any obvious errors in my nginx.conf file, but maybe I'm not checking something? The first couple of lines of the nginx config file: user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } Any help is appreciated, thanks a lot in advance!

    Read the article

  • reset locale in debian under Squeeze

    - by si2w
    I have problems with locale in debian. I tried many thing but it doesn't anything for me : locale -a locale: Cannot set LC_CTYPE to default locale: No such file or directory C POSIX en_US.utf8 I try to set en_US.utf8 without success with this :dpkg-reconfigure locales -plow perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = "en_US", LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = (unset) are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory /usr/bin/locale: Cannot set LC_CTYPE to default locale: No such file or directory /usr/bin/locale: Cannot set LC_ALL to default locale: No such file or directory Generating locales (this might take a while)... en_US.UTF-8... done Generation complete. perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = "en_US", LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = (unset) are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = "en_US", LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = (unset) are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). After reboot, i try to use a perl script : perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = "en_US", LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = "en_US.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). Here is my /etc/default/locale config file : cat /etc/default/locale LANG=en_US.UTF-8 LANGUAGE=en_US Any idea to solve this (stupid) problem ? Thanks

    Read the article

  • IIS 6 Windows Authentication in ASP.Net app fails

    - by Kjensen
    I am trying to install an ASP.Net app on an IIS6 webserver. The site requires the user to authenticate with windows, and this works on several other apps on the same server. In IIS I have enabled anonymous access and windows authentication. In web.config, authentication is set to: <authentication mode="Windows"/> and authorization...: <authorization> <allow roles="Users"/> <deny users="*"/> </authorization> Ie. allow all users in role "Users" and deny everybody else. This is the approach that is working with several other apps on the same server. If I run the site, I am prompted for username and password. If I remove the line: <deny users="*"/> I can access the site and everything works - but the user credentials are not passed to the site (Page.User.Identity.Name returns a blank string in ASP.Net). The site has identical (inherited) file permissions as other working sites on the server. The only difference in authentication/authorization between this site and the other working sites is, that this runs Asp.Net 4 (but there are other working asp.net 4 sites on the server as well). What am I missing here? Where should I look?

    Read the article

  • Debian, 2 NICs load-balancing or agregating with one same gateway

    - by pouney
    Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

    Read the article

  • Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

    - by Kjensen
    A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

    Read the article

  • Selecting Interface for SSH Port Forwarding

    - by Eric Pruitt
    I have a server that we'll call hub-server.tld with three IP addresses 100.200.130.121, 100.200.130.122, and 100.200.130.123. I have three different machines that are behind a firewall, but I want to use SSH to port forward one machine to each IP address. For example: machine-one should listen for SSH on port 22 on 100.200.130.121, while machine-two should do the same on 100.200.130.122, and so on for different services on ports that may be the same across all of the machines. The SSH man page has -R [bind_address:]port:host:hostport listed I have gateway ports enabled, but when using -R with a specific IP address, server still listens on the port across all interfaces: machine-one: # ssh -NR 100.200.130.121:22:localhost:22 [email protected] hub-server.tld (Listens for SSH on port 2222): # netstat -tan | grep LISTEN tcp 0 0 100.200.130.121:2222 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN tcp 0 0 :::80 :::* LISTEN Is there a way to make SSH forward only connections on a specific IP address to machine-one so I can listen to port 22 on the other IP addresses at the same time, or will I have to do something with iptables? Here are all the lines in my ssh config that are not comments / defaults: Port 2222 Protocol 2 SyslogFacility AUTHPRIV PasswordAuthentication yes ChallengeResponseAuthentication no GSSAPIAuthentication no GSSAPICleanupCredentials no UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes ClientAliveInterval 30 ClientAliveCountMax 1000000 UseDNS no Subsystem sftp /usr/libexec/openssh/sftp-server

    Read the article

  • Missing whole disk device in OpenSolaris

    - by Jeff Mc
    I have begun experimenting with Solaris and ZFS as a NAS. All was going very smoothly until I had a drive failure. When I replaced the drive, I no longer have a device file mapped to the whole disk. /dev/dsk/c7t3d0 does not exist but c7t2d0 and c7t4d0 both do. Also the sd@3,0:wd file under the /devices/ tree is non-existent. Do I have to prepare/partition the disk somehow to cause the whole disk device to exist? Here are a few outputs that might be useful. jeffmc@ats-ds2:/dev/dsk$ zpool status pool: datapool state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using 'zpool online'. see: http://www.sun.com/msg/ZFS-8000-2Q scrub: none requested config: NAME STATE READ WRITE CKSUM datapool DEGRADED 0 0 0 mirror-0 DEGRADED 0 0 0 c7t2d0 ONLINE 0 0 0 c7t3d0 UNAVAIL 0 0 0 cannot open mirror-1 ONLINE 0 0 0 c7t4d0 ONLINE 0 0 0 c7t5d0 ONLINE 0 0 0 jeffmc@ats-ds2:/dev/dsk$ zpool replace datapool c7t3d0 cannot open 'c7t3d0': no such device in /dev/dsk must be a full path or shorthand device name jeffmc@ats-ds2:/dev/dsk$ sudo format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c7t0d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@0,0 1. c7t1d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@1,0 2. c7t2d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@2,0 3. c7t3d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@3,0 4. c7t4d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@4,0 5. c7t5d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@5,0

    Read the article

  • Unexpected(?) high 'wasted' memory in memcached

    - by Nanne
    Looking at our memcached stats I think I have found an issue I was not aware of before. It seems that we have a strangely high amount of wasted space. I checked with phpmemcacheadmin for a change, and found this image staring at me: Now I was under the impression that the worst-case scenario would be that there is 50% waste, although I am the first to admit not knowing all the details. I have read - amongst others- this page which is indeed somewhat old, but so is our version of memcached. I think I do understand how the system works (e.g.) I believe, but I have a hard time understanding how we could get to 76% wasted space. The eviction rate that phpmemcacheadmin shows is 2 ev/s, so there is some problem here. The primary question is: what can I do to fix this. I could throw more memory at it (there is some extra available I think), maybe I should fiddle with the slab config (is that even possible with this version?), maybe there are other options? Upgrading the memcached version is not a quickly available option. The secondairy question, out of curiosity, is of course if the rate of 75% (and rising) wasted space is expected, and if so, why. System: This is currently not something I can do anything about, I know the memcached version isn't the newest, but these are the cards I've been dealt. Memcached 1.4.5 Apache 2.2.17 PHP 5.3.5

    Read the article

  • Tunneling a public IP to a remote machine

    - by Jim Paris
    I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

    Read the article

  • nginx- Rewrite URL with Trailing Slash

    - by Bryan
    I have a specialized set of rewrite rules to accommodate a mutli site cms setup. I am trying to have nginx force a trailing slash on the request URL. I would like it to redirect requests for domain.com/some-random-article to domain.com/some-random-article/ I know there are semantic considerations with this, but I would like to do it for SEO purposes. Here is my current server config. server { listen 80; server_name domain.com mirror.domain.com; root /rails_apps/master/public; passenger_enabled on; # Redirect from www to non-www if ($host = 'domain.com' ) { rewrite ^/(.*)$ http://www.domain.com/$1 permanent; } location /assets/ { expires 1y; rewrite ^/assets/(.*)$ /assets/$http_host/$1 break; } # / -> index.html if (-f $document_root/cache/$host$uri/index.html) { rewrite (.*) /cache/$host$1/index.html break; } # /about -> /about.html if (-f $document_root/cache/$host$uri.html) { rewrite (.*) /cache/$host$1.html break; } # other files if (-f $document_root/cache/$host$uri) { rewrite (.*) /cache/$host$1 break; } } How would I modify this to add the trailing slash? I would assume there has to be a check for the slash so that you don't end up with domain.com/some-random-article//

    Read the article

< Previous Page | 325 326 327 328 329 330 331 332 333 334 335 336  | Next Page >