Search Results

Search found 2918 results on 117 pages for 'brian scott'.

Page 33/117 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

  • SLI Video Cards

    - by Scott
    I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

    Read the article

  • Windows Server 2008 R2 and Keyboards

    - by Brian
    Hello, I have a machine with WIN server 2008 R2 installed, when the machine boots up, it says keyboard failure. The keyboard I had was from an older machine and was PS/2, I got a PS/2 to USB converter in order for it to work, but it says keyboard failure and doesn't work. Is it because it's pretty old and that's it, or does it have to be USB? I'm going to look into a new one, but want to make sure I don't get this issue again... Thanks.

    Read the article

  • Rewrite URL based off of IP on OpenWRT

    - by Scott
    We are running OpenWRT on a WRT54GL. I have been looking for an answer to this, but I can't seem to figure out what to search for, if its possible, or what combination of programs to use. I want to be able to redirect a HTTP request from a WiFi device based off of their MAC address. This should all be transparent to the device. Basically we are trying to redirect any non-registered devices to a website to register the device (at this point, we would push a new config to the router that would allow this MAC address "full access"). Once a device is registered, it will be redirected to a transparent squid proxy server on another machine for caching/blocking certain sites. I looked at tinyproxy - popilo which redirects but I won't have the MAC address to know if its registered or not. Any help (google suggestions, programs, anything!) would be very much appreciated!

    Read the article

  • Windows Explorer slow to open networked computer, fast to navigate once opened

    - by Scott Noyes
    I open Windows Explorer and enter an IP for a computer on my home network (\\192.168.1.101). It takes 30 seconds or more to present a list of the shared folders. It does not appear to be an initial handshaking/authentication thing; even if I allow the view to load and then immediately load the same again, it is always slow. Once they appear, navigating through folders and opening files is fast. Also, navigating directly to a folder (\\192.168.1.101\My Music) is fast, even if it's the first connection since a restart. Using \\computerName instead of the IP address gives exactly the same results. Pings return in 1ms. net view \\computerName (or \ipAddress) returns the list of shared folders fast. This makes me suspect an Explorer issue rather than a network issue. Suspecting that the remote computer was being automatically indexed or something, I went into Tools-Folder Options-View and unchecked "Automatically search for network folders and printers," but that made no difference. De-selecting the "Folders" icon near the address bar makes no difference. Adding the IP address and computer name to the hosts file makes no difference. Both computers involved are laptops running Windows XP. Both have WiFi and cable adapters. Mine is not connected via cable. The result is the same whether the target is plugged in to the cable or not (although the IP address changes - 192.168.1.101 over cable, 192.168.1.103 over WiFi.) We are using DHCP assigned by the router.

    Read the article

  • Make my IP address appear to be from another country

    - by Brian
    How do I make it appear that my IP address is coming from one country while I'm located in another? I live in Germany and some websites (like Hulu or Youtube) don't work because my IP isn't in the US. How do I get around this? Do I have to use a proxy or something? Moderator note Super User does not endorse nor defend any activity which may be used to circumvent local/state/national laws.

    Read the article

  • CommunicationException when shutting down JBoss 4.2.2

    - by Brian
    I have deployed an application using JBoss 4.2.2 on a 64-bit RHEL5 server. Since there are other JBoss servers, I had to change some port configurations so that there would be no conflicts when starting the server. So right now I'm using ports-01 from the sample-bindings.xml file that came in the docs/examples/binding-manager/samples directory. In addition, below is a list of all the files I've edited to reflect the new ports: JBOSS_HOME/servers/default/deploy/jboss-web.deployer/server.xml: Changed Connector port - 8080 to 8180 Changed AJP 1.3 Connector port - 8009 to 8109 JBOSS_HOME/server/default/deploy/jbossws.beans/META-INF/jboss-beans.xml Changed 8080 to 8180 JBOSS_HOME/server/default/conf/jboss-service.xml: Changed 8083 to 8183 Changed 1099 to 1299 Changed 1098 to 1298 Changed 4444 to 4644 Changed 4445 to 4645 Changed 4446 to 4646 Changed 4447 to 4647 JBOSS_HOME/server/default/conf/jboss-minimal.xml: Changed 1099 to 1299 Changed 1098 to 1298 When I start the server (binding to localhost) everything is fine and I'm able to access the application. But when I try to shutdown the server I get the following error: Exception in thread "main" javax.naming.CommunicationException: Could not obtain connection to any of these urls: localhost [Root exception is javax.naming.CommunicationException : Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]]] at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1562) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:634) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:627) at javax.naming.InitialContext.lookup(InitialContext.java:392) at org.jboss.Shutdown.main(Shutdown.java:214) Caused by: javax.naming.CommunicationException: Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:274) at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1533) ... 4 more Caused by: javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:248) ... 5 more Caused by: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:525) at java.net.Socket.connect(Socket.java:475) at java.net.Socket.(Socket.java:372) at java.net.Socket.(Socket.java:273) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:84) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:77) at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:244) ... 5 more Is there any other file that I need to change the 1099 to 1299, or am I missing some other step?

    Read the article

  • Creating a bootable external drive in OSX

    - by Brian Postow
    I want to do some slightly dangerous testing, testing an install package I've written, so I've got an external drive, and I want to make it a bootable OSX disk, then I can boot up on the external, do my install, and if it screws things up, it doesn't actually affect the usability of my machine. The problem is that when I stick the disk that came with my computer (It's actually another computer in the office, but they're both minis) in and try to run the installer, it says "You cannot install OSx 10.6 on this computer". Now, the computer is ALREADY running 10.6, so that's a kind of silly error message... It does this when I boot to the DVDRom as well. Am I doing something really really dumb? or what?

    Read the article

  • Is it possible to integrate Computer Associates SiteMinder with SQLServer?

    - by Scott Weinstein
    We have a MS SQL BI stack which the standards group wants us to move to "WebSSO" which is based on Computer Associates SiteMinder/netegrity product. I figure integrating the web component won't be too hard, but we have users which connect to the Database directly - currently using Windows Authentication. Is is possible to itegrate Computer Associates SiteMinder with SQL Server? With SSAS? If so, how much effort is involved?

    Read the article

  • Ubuntu 12.04 - HP ProLiant DL380 G4 - Load Maxes Out / Unresponsive

    - by Brian S
    Trying to post this question on here. I've posted it on the Ubuntu forums as well with no replies. Recently I upgraded an HP ProLiant DL380 G4 server from Ubuntu 10.04 server to Ubuntu 12.04 server. Upon doing so, the server will not - at random times - get to a load of 400+ and then become completely non-responsive. I use an SNMP graphing program (cacti) and the load steadily increases by about 10 every five minutes until it gets over 400 and the graphing stops. The graphs may not be accurate, but the CPU load averages about 3% before this happens - and right when the load starts increasing, it jumps to about 25% for 15 minutes and dramatically dips down to less than 1% (about 0.3%) until the graphing stops. I'm not able to open a SSH tunnel to the server to do anything. I've checked the /var/log/syslog and all logging stops at that time as well - with nothing else in there. The odd thing is - the server still responds to DNS queries for the zones it is authoritative on during this time - and at normal speed. Just not sure what the next step would be in order to find out what is going on - and how this issue can be corrected. The server cannot stay with Ubuntu 10.04 Server and needs to stay upgraded.

    Read the article

  • How can I restore my system from WIM files?

    - by Brian Henk
    I installed another OS on my netbook and decided I want to revert back to Windows 7 Starter. I was careful to keep the recovery partition, but even when I manage to boot to it, the system just restarts a few seconds after selecting "restore." I grabbed all the files from the recovery partition onto a flash drive. I also have been able to use this drive to boot a Windows 7 install, but it was unable to find the recovery partition. These WIM files seem to be the key to installing Windows again. How can I use them?

    Read the article

  • Links won't open in Outlook

    - by Scott Mitchell
    About a week ago Chrome (my default browser) stopped working and I ended up reinstalling. After that, however, links in Outlook 2007, when clicked, no longer open. Instead, I get a warning that reads: General failure. The URL was: URL. Application not found. I presume that there is some MIME or file type association that needs to be configured at the OS level, but I've not had any luck so far. My operating system is Windows 7. Any ideas? EDIT #1 Wayne Johnston suggested I set Chrome as my default browser, but when I go to the Set Default Programs screen in Windows 7 (via Control Panel) I do not see Chrome in the list of programs. How do I get it to show up there?

    Read the article

  • Change Drobo directory permissions

    - by Steven Scott
    I have a Drobo unit that is connected via fire-wire to a Dell notebook. Using Ubuntu 12.04. I can not seem to change the permissions to allow all users to have read/write access to the drives. The unit is automatically mounting the volumes as my user using the system, so other applications can not access the device. I want to set up a Plex Media Server to stream music, etc... but it will not scan the drives since it can not access them. How can I change the permissions to allow everyone to read the volumes? IF I add them to the fstab as ntfs volumes, Ubuntu reports that they are not available during the boot up, likely due to the fire-wire not having found the drives yet. Any ideas or suggestions would be greatly appreciated.

    Read the article

  • I'm receiving an SSL error in various browsers, but I can't find non-SSL content

    - by Scott Vercuski
    I'm receiving an error with my SSL connection. Using google chrome I see the following error: Your connection is encrypted with 128-bit encryption ... however this page includes other resources which are not secure I've scoured the source code, scripts and rendered code in the browser but cannot find where an http:// call is made. I've also used Fiddler2 to examine the traffic and everything is coming across via HTTPS. Has anyone run into this issue before and if so how did you go about finding the culprit. The website is running ASP.NET MVC3 in C#. The page in question is a simple payment page. The only external call is the google analytics tracking code. The page appears to load correctly, all images and scripts are in place.

    Read the article

  • Why is SMF manifest losing configuration data when exported on SmartOS?

    - by Scott Lowe
    I'm running a server process under SMF (Server Management Facility) on Joyent's Base64 1.8.1 SmartOS image. For those not aqauinted with SmartOS, it is a cloud-based distribution of IllumOS with KVM. But essentially it is like Solaris and inherits from OpenSolaris. So even if you've not used SmartOS, I'm hoping to tap into some Solaris knowledge on ServerFault. My issue is that I want an unprivileged user to be allowed to restart a service that they own. I have worked out how to do that by using RBAC and adding an authorisation to /etc/security/auth_attr and associating that authorisation with my user. I then added the following to my SMF manifest for the service: <property_group name='general' type='framework'> <!-- Allow to be restarted--> <propval name='action_authorization' type='astring' value='solaris.smf.manage.my-server-process' /> <!-- Allow to be started and stopped --> <propval name='value_authorization' type='astring' value='solaris.smf.manage.my-server-process' /> </property_group> And this works well when imported. My unprivileged user is allowed to restart, start and stop its own server process (this is for automated code deployments). However, if I export the SMF manifest, this configuration data is gone... all I see in that section is this: <property_group name='general' type='framework'> <property name='action_authorization' type='astring'/> <property name='value_authorization' type='astring'/> </property_group> Does anybody know why this is happening? Is my syntax wrong, or am I simply not using SMF incorrectly?

    Read the article

  • Move MySQL database while instance is online

    - by Mike Scott
    I have a MySQL instance containing a number of databases, one of which is an archive database (although using the INNODB rather than ARCHIVE storage engine) that is not queried or written to in normal operation. The data filesystem is filling up and I'd like to move the archive database's data directory to a different filesystem (and then symlink it back, obviously). If there are no SQL statements attempting to query or update the data during the move, can I safely do this while the MySQL instance and the other databases stay online and in use? I plan to rsync the database directory to the new filesystem, then rename the old one on the original filesystem to something different and create the new symlink. lsof reports that MySQL does have the .ibd files open, so presumably it would have to reopen them.

    Read the article

  • using iptables to change a destination port but keep the ip the same.

    - by Scott Chamberlain
    I am playing around with transparent proxies, The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated.

    Read the article

  • Why is SSH finding remote keys for other accounts?

    - by Brian Pontarelli
    This is a strange issue I'm having with SSH from my Macbook Pro to a Linux (Ubuntu 11.10) server. I have a DSA key setup on the remote Linux server under my home directory like this: /home/me/.ssh/authorzied_keys I also have the same DSA key setup for a few other accounts on the machine named "foo" and "bar". I can log into all of the accounts fine without any password. Therefore, the DSA keys are all setup correctly. The strange behavior I'm seeing is when debugging the SSH connection. During the connection, the SSH debug is outputting this: debug2: key: /Users/me/.ssh/id_dsa (0x7f91a1424220) debug2: key: /home/foo/.ssh/id_dsa (0x7f91a1425620) debug2: key: /home/bar/.ssh/id_rsa (0x7f91a1425c60) debug2: key: /Users/me/.ssh/id_rsa (0x0) This is strange for so many reasons, but essentially, why is SSH listing out keys on the server (/home/foo/.ssh/id_dsa and /home/bar/.ssh/id_rsa)? These files don't even exist on the server, so why are they listed? I'm not logging into the "foo" or "bar" accounts, so why is SSH even listing those? On my Macbook Pro, I only have a DSA key, but SSH is listing out an RSA key, what's that all about? Another user on the server doesn't get any of these messages when they log in and they have the exact same setup for their DSA key and the exact same Macbook Pro setup as mine? Does anyone know what these messages are and why SSH is outputting them?

    Read the article

  • Problem opening XWindows programs with xming and SSH Secure Shell

    - by Brian
    I've installed SSH Secure Shell and xming on my laptop running Windows 7 (64-bit). I'm having trouble starting X Windows applications from the SSH console. I've been able to do it in the past. I've pretty much determined that it's not a server issue because I've tried it on two different servers (both servers are running RHEL 5). Running "echo $DISPLAY" on either server gave me "localhost:10.0". My XLaunch configuration settings are: Multiple Windows, 10 (display number), and Start no client. Once xming has launched, I'll try to execute something like "firefox" and I get this back: The application 'firefox' lost its connection to the display localhost:10.0; most likely the X server was shut down or you killed/destroyed the application. I've already checked to make sure that the X server is running and it is: root 12579 2689 0 Feb14 tty7 00:04:23 /usr/bin/Xorg :0 -br -audit 0 -auth /var/gdm/:0.Xauth -nolisten tcp vt7 Additionally, X11 Tunneling has been enabled in SSH as well as SSH 2 connections.

    Read the article

  • How do I remove Slony from a restored PostgreSQL database?

    - by Scott Herbert
    I've restored a database which came from a server on which Slony was running. The server on which the database has been restored does not have Slony installed. When the database restored, there were a lot of errors reported, with Slony related objects not getting created due to Slony related logins being missing. This I thought was not a problem, as losing the Slony objects didn't seem to matter, and infact seemed desirable. However, now I've got an anoying, if not critical problem. Whenever one clicks on a table in the newly restored DB in PGAdmin, a Slony related error popup ... pops up. The first one reads: "An error has occured: ERROR: function _rmscl.getlocalnodeid(unknown) does not exist" I notice that under the Replication node in PGAdmin, that there is a Slony replication cluster. Trying to drop this cluster results in more object missing type errors. Does anyone have any ideas how we can remove the last vestiges of Slony from this database?

    Read the article

  • DVI to USB adapter - Worth it?

    - by Brian
    Hello, I have a DVI TV, and was wondering if anyone has tried out the DVI to USB adapter and could let me knwo what kind of quality it has... was it worth it? Was thinking of using it for online TV (don't have a wireless device)... Thanks.

    Read the article

  • Applying the Windows Experience Index to Servers

    - by Scott
    I finally convinced upper management that we need a computer replacement plan, and I've been tasked with making an inventory of what we have and determining what needs to be replaced this year, next year, the year after, etc. I had to use some sort of criteria to back up my recommendations, so I decided to try using the Windows Experience Index. I've determined the CPU and Memory scores for all of our desktops and servers using community data. I also feel fairly successful in assigning a WEI score to each user based on their computing needs. I'm struggling with assigning a WEI score to the various servers that we have: file server, database server, Exchange server, backup server (for doing backups), web server. Suggestions would be appreciated.

    Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >