Search Results

Search found 2782 results on 112 pages for 'policy'.

Page 33/112 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

• How to send email from home ip when the email server isn't a designated outbound mail server allocated to BT Retail customers [on hold]

  - by Mr Shoubs

  (I am sys admin!) I can receive email, but when I try to send an email from my home office via our work email server I get the following reply: Your message did not reach some or all of the intended recipients. Subject: Test Sent: 19/08/2014 17:02 The following recipient(s) cannot be reached: 'Joe Blogs' on 19/08/2014 17:02 Server error: '554 5.7.1 Service unavailable; Client host [my-ip-here] blocked using zen.spamhaus.org; http://www.spamhaus.org/query/bl?ip=my-ip-here' I went to that URL and it says the following: Ref: PBL231588 81.152.0.0/13 is listed on the Policy Block List (PBL) Outbound Email Policy of BT Retail for this IP range: It is the policy of BT Retail that unauthenticated email sent from this IP address should be sent out only via the designated outbound mail server allocated to BT Retail customers. Please consult the following URL for details on how to configure your email client appropriately. http://btybb.custhelp.com/cgi-bin/btybb.cfg/php/enduser/cci/bty_adp.php?p_sid=fPnV4zhj&p_faqid=6876 Removal Procedure Removal of IP addresses within this range from the PBL is not allowed by the netblock owner's policy. Going to this URL just says: This site has been disabled for the time being. Does anyone know what I should do to allow me to send emails from my home ip - the site suggests I can configure my email client? (note that I have configured the client to use smtp authentication)

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• Install multiport module on iptables

  - by tarteauxfraises

  I'am trying to install "fail2ban" on Cubidebian, a Debian port for Cubieboard (A raspberry like board). The following rule failed due to "-m multiport --dports ssh" options (It works, when i run manually the command without multiple options). $ iptables -I INPUT -p tcp -m multiport --dports ssh -j fail2ban-ssh" iptables: No chain/target/match by that name. When i make a cat on "/proc/net/ip_tables_matches", i see that multiport module is not loaded: $ cat /proc/net/ip_tables_matches u32 time string statistic state owner pkttype mac limit helper connmark mark ah icmp socket socket quota2 policy length iprange ttl hashlimit ecn udplite udp tcp The result of iptables -L -n -v command : $ iptables -L -n -v Chain INPUT (policy ACCEPT 6 packets, 456 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 3 packets, 396 bytes) pkts bytes target prot opt in out source destination Chain fail2ban-apache (0 references) pkts bytes target prot opt in out source destination 0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (0 references) pkts bytes target prot opt in out source destination 0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0 What can i do to compile or to enable the multiport module? Thanks in advance for your help

  Read the article

• ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

  - by chickenloop

  I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

  Read the article

• iptables port redirection on Ubuntu

  - by Xi.

  I have an apache server running on 8100. When open http://localhost:8100 in browser we will see the site running correctly. Now I would like to direct all request on 80 to 8100 so that the site can be accessed without the port number. I am not familiar with iptables so I searched for solutions online. This is one of the methods that I have tried: user@ubuntu:~$ sudo iptables -A INPUT -p tcp --dport 80 -j ACCEPT user@ubuntu:~$ sudo iptables -A INPUT -p tcp --dport 8100 -j ACCEPT user@ubuntu:~$ sudo iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-ports 8100 It's not working. The site works on 8100 but it's not on 80. If print out the rules using "iptables -t nat -L -n -v", this is what I see: user@ubuntu:~$ sudo iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 14 packets, 2142 bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 redir ports 8100 Chain INPUT (policy ACCEPT 14 packets, 2142 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 177 packets, 13171 bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 177 packets, 13171 bytes) pkts bytes target prot opt in out source destination The OS is a Ubuntu on a VMware. I thought this should be a simple task but I have been working on it for hours without success. :( What am I missing?

  Read the article

• Prevent Changing the Screen Saver and Wallpaper in Windows 7

  - by Mysticgeek

  Sometimes you might not want users to have the ability to change Screen Savers and Wallpaper on Windows 7 workstations. Today we look at how to prevent them from changing either one or both. You might administer computers in your home or small office and find it annoying when users continuously change the wallpaper and Screen Savers to something obnoxious. A lot of times they might be inexperienced users and download these so-called “wonderful and free” Screen Saver/Wallpaper packages from shady sites that include loads of Spyware. Preventing users from changing them is another helpful tool to avoid wasteful time spent switching things back. Prevent Changing Screensavers & Wallpaper Using Group Policy Editor  Note: This method uses Group Policy which is not available in Home versions on Windows 7. Open the Start Menu and enter gpedit.msc into the Search box and hit Enter. When Local Group Policy Editor opens, navigate to User Configuration \ Administrative Templates \ Control Panel \ Personalization. Then in the right column double-click on Prevent changing desktop background. Now check the radio button next to Enabled, then click OK. Back on the Group Policy Screen, double-click on Prevent changing screen saver. In the next screen select the radio button next to Enable, click OK, then close out of Group Policy Editor. Now when a user goes into the Personalization section, the Desktop Background hyperlink is now grayed out and inactive. Notice the message One or more of the settings on this page has been disabled by the system administrator at the bottom of the section. If they click to change the Screen Saver, an error message will pop up letting them know the function is disabled. Prevent Changing Screensavers & Wallpaper Using a Registry Hack You can also make a couple Registry changes to prevent users from changing the Wallpaper & Screen Saver…which will work on Home versions of Windows 7. Before making any Registry changes make sure you back it up first. Open the Registry by typing regedit into the Search box in the Start menu and hit Enter. First we’ll start with the Wallpaper. Navigate to HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System and create a new String Value and name it Wallpaper. Then modify the Value data to point to the location of the Wallpaper you want it to always be. Where in this example it’s our main wallpaper on our local drive…then click OK. Now let’s make sure they can’t change the Screen Saver. In the same Registry location, we need to make a new DWORD (32-bit) Value. Give it the Value name of NoDispScrSavPage and the value data of “1” and click OK. Close out of the Registry and restart the machine or simply log off then back on again for the changes to take effect. Results For the Wallpapers, a user can still go in and see the selections, however if they try to change it to something else… It will just go back to the Personalization screen and no changes will be made, as we set the value to only be the background we specified. If the user tries to make a change to the Screen Saver, the hyperlink will be grayed out and inactive, and the message One or more of the settings on this page has been disabled by the system administrator will be displayed at the bottom of the section. Conclusion If you’re tired of users changing the Wallpaper and Screen Saver, and want another way to help avoid Malware, locking down these settings can help a lot. Again, before making any changes to the Registry, make sure to back it up. These settings should work in Vista and XP as well. Similar Articles Productive Geek Tips Save 1-4% More Battery Life With Windows Vista Battery SaverCustomize Your Windows Vista Logon ScreenEnable "Ubuntu Style" Logons in Windows VistaManage the Delete Confirmation Dialog box in Windows 7Dual Monitors: Use a Different Wallpaper on Each Desktop TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Fun with 47 charts and graphs Tomorrow is Mother’s Day Check the Average Speed of YouTube Videos You’ve Watched OutlookStatView Scans and Displays General Usage Statistics How to Add Exceptions to the Windows Firewall Office 2010 reviewed in depth by Ed Bott

  Read the article

• OS Analytics with Oracle Enterprise Manager (by Eran Steiner)

  - by Zeynep Koch

  Oracle Enterprise Manager Ops Center provides a feature called "OS Analytics". This feature allows you to get a better understanding of how the Operating System is being utilized. You can research the historical usage as well as real time data. This post will show how you can benefit from OS Analytics and how it works behind the scenes. The recording of our call to discuss this blog is available here: https://oracleconferencing.webex.com/oracleconferencing/ldr.php?AT=pb&SP=MC&rID=71517797&rKey=4ec9d4a3508564b3Download the presentation here See also: Blog about Alert Monitoring and Problem Notification Blog about Using Operational Profiles to Install Packages and other content Here is quick summary of what you can do with OS Analytics in Ops Center: View historical charts and real time value of CPU, memory, network and disk utilization Find the top CPU and Memory processes in real time or at a certain historical day Determine proper monitoring thresholds based on historical data Drill down into a process details Where to start To start with OS Analytics, choose the OS asset in the tree and click the Analytics tab. You can see the CPU utilization, Memory utilization and Network utilization, along with the current real time top 5 processes in each category (click the image to see a larger version):  In the above screen, you can click each of the top 5 processes to see a more detailed view of that process. Here is an example of one of the processes: One of the cool things is that you can see the process tree for this process along with some port binding and open file descriptors. Next, click the "Processes" tab to see real time information of all the processes on the machine: An interesting column is the "Target" column. If you configured Ops Center to work with Enterprise Manager Cloud Control, then the two products will talk to each other and Ops Center will display the correlated target from Cloud Control in this table. If you are only using Ops Center - this column will remain empty. The "Threshold" tab is particularly helpful - you can view historical trends of different monitored values and based on the graph - determine what the monitoring values should be: You can ask Ops Center to suggest monitoring levels based on the historical values or you can set your own. The different colors in the graph represent the current set levels: Red for critical, Yellow for warning and Blue for Information, allowing you to quickly see how they're positioned against real data. It's important to note that when looking at longer periods, Ops Center smooths out the data and uses averages. So when looking at values such as CPU Usage, try shorter time frames which are more detailed, such as one hour or one day. Applying new monitoring values When first applying new values to monitored attributes - a popup will come up asking if it's OK to get you out of the current Monitoring Policy. This is OK if you want to either have custom monitoring for a specific machine, or if you want to use this current machine as a "Gold image" and extract a Monitoring Policy from it. You can later apply the new Monitoring Policy to other machines and also set it as a default Monitoring Profile. Once you're done with applying the different monitoring values, you can review and change them in the "Monitoring" tab. You can also click the "Extract a Monitoring Policy" in the actions pane on the right to save all the new values to a new Monitoring Policy, which can then be found under "Plan Management" -> "Monitoring Policies". Visiting the past Under the "History" tab you can "go back in time". This is very helpful when you know that a machine was busy a few hours ago (perhaps in the middle of the night?), but you were not around to take a look at it in real time. Here's a view into yesterday's data on one of the machines: You can see an interesting CPU spike happening at around 3:30 am along with some memory use. In the bottom table you can see the top 5 CPU and Memory consumers at the requested time. Very quickly you can see that this spike is related to the Solaris 11 IPS repository synchronization process using the "pkgrecv" command. The "time machine" doesn't stop here - you can also view historical data to determine which of the zones was the busiest at a given time: Under the hood The data collected is stored on each of the agents under /var/opt/sun/xvm/analytics/historical/ An "os.zip" file exists for the main OS. Inside you will find many small text files, named after the Epoch time stamp in which they were taken If you have any zones, there will be a file called "guests.zip" containing the same small files for all the zones, as well as a folder with the name of the zone along with "os.zip" in it If this is the Enterprise Controller or the Proxy Controller, you will have folders called "proxy" and "sat" in which you will find the "os.zip" for that controller The actual script collecting the data can be viewed for debugging purposes as well: On Linux, the location is: /opt/sun/xvmoc/private/os_analytics/collect If you would like to redirect all the standard error into a file for debugging, touch the following file and the output will go into it: # touch /tmp/.collect.stderr   The temporary data is collected under /var/opt/sun/xvm/analytics/.collectdb until it is zipped. If you would like to review the properties for the Analytics, you can view those per each agent in /opt/sun/n1gc/lib/XVM.properties. Find the section "Analytics configurable properties for OS and VSC" to view the Analytics specific values. I hope you find this helpful! Please post questions in the comments below. Eran Steiner

  Read the article

• Why do ICMP Redirct Host happen?

  - by El Barto

  I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Why do ICMP Redirect Host happen?

  - by El Barto

  I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• iptables is not allowing me to contact my dns nameservers

  - by user1272737

  I have the follwing iptables rules: Chain INPUT (policy DROP) target prot opt source destination ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- localhost.localdomain anywhere tcp dpt:mysql ACCEPT tcp -- anywhere anywhere tcp dpt:14443 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:xxxxxxx Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination When I turn off iptables I am able to use wget and all other commands. When these rules are enabled I cannot connect to any address. Any idea why this would be?

  Read the article

• Juniper SSG-5 subinterface vlan routing to the internet

  - by catfish

  I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• NPS EAP authentication failing after Windows Update

  - by sqlreader

  I have a Windows 2008 Std server running NPS. After applying the latest round of updates (including Root Certificates for April 2012 KB931125 (See:http://support.microsoft.com/kb/933430/)), EAP authentication is failing due to being malformed. Sample error (Security/Event ID 6273), truncated for brevity: Authentication Details: Proxy Policy Name: Use Windows authentication for all users Network Policy Name: Wireless Access Authentication Provider: Windows Authentication Server: nps-host.corp.contoso.com Authentication Type: PEAP EAP Type: - Account Session Identifier: - Reason Code: 266 Reason: The message received was unexpected or badly formatted. The NPS policy (Wireless Access) is configured accordingly (for Constraints/Authentication methods) EAP Types: Microsoft: Protected EAP (PEAP) - with a valid certificate from ADCS Microsoft: Secured password (EAP-MSCHAP v2) Less secure authentication methods: Microsoft Encrypted Authentication version 2 (MS-CHAP-v2) User can change password after it has expired Microsoft Encrypted Authentication (MS-CHAP) User can change password after it has expired We've tested a different RADIUS server without the aforementioned patch, and removed EAP as an authentication type and experienced success. Has anyone else experienced this issue?

  Read the article

• OpenVPN on ec2 bridged mode connects but no Ping, DNS or forwarding

  - by michael

  I am trying to use OpenVPN to access the internet over a secure connection. I have openVPN configured and running on Amazon EC2 in bridge mode with client certs. I can successfully connect from the client, but I cannot get access to the internet or ping anything from the client I checked the following and everything seems to shows a successful connection between the vpn client/server and UDP traffic on 1194 [server] sudo tcpdump -i eth0 udp port 1194 (shows UDP traffic after establishing connection) [server] sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] sudo iptables -L -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- ip-W-X-Y-0.us-west-1.compute.internal/24 anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] openvpn.log Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 [localhost] Inactivity timeout (--ping-restart), restarting Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 SIGUSR1[soft,ping-restart] received, client-instance restarting Wed Oct 19 03:41:31 2011 MULTI: multi_create_instance called Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Re-using SSL/TLS context Wed Oct 19 03:41:31 2011 a.b.c.d:57889 LZO compression initialized Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Control Channel MTU parms [ L:1574 D:166 EF:66 EB:0 ET:0 EL:0 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Local Options hash (VER=V4): '360696c5' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Expected Remote Options hash (VER=V4): '13a273ba' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 TLS: Initial packet from [AF_INET]a.b.c.d:57889, sid=dd886604 ab6ebb38 Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=EXAMPLE_CA/[email protected] Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=localhost/[email protected] Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Oct 19 03:41:37 2011 a.b.c.d:57889 [localhost] Peer Connection Initiated with [AF_INET]a.b.c.d:57889 Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 PUSH: Received control message: 'PUSH_REQUEST' Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 SENT CONTROL [localhost]: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route-gateway W.X.Y.Z,ping 10,ping-restart 120,ifconfig W.X.Y.Z 255.255.255.0' (status=1) Wed Oct 19 03:41:40 2011 localhost/a.b.c.d:57889 MULTI: Learn: (IPV6) -> localhost/a.b.c.d:57889 [client] tracert google.com Tracing route to google.com [74.125.71.104] over a maximum of 30 hops: 1 347 ms 349 ms 348 ms PC [w.X.Y.Z] 2 * * * Request timed out. I can also successfully ping the server IP address from the client, and ping google.com from an SSH shell on the server. What am I doing wrong? Here is my config (Note: W.X.Y.Z == amazon EC2 private ipaddress) bridge config on br0 ifconfig eth0 0.0.0.0 promisc up brctl addbr br0 brctl addif br0 eth0 ifconfig br0 W.X.Y.X netmask 255.255.255.0 broadcast W.X.Y.255 up route add default gw W.X.Y.1 br0 /etc/openvpn/server.conf (from https://help.ubuntu.com/10.04/serverguide/C/openvpn.html) local W.X.Y.Z dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;server W.X.Y.0 255.255.255.0 server-bridge W.X.Y.Z 255.255.255.0 W.X.Y.105 W.X.Y.200 ;push "route W.X.Y.0 255.255.255.0" push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" tls-auth ta.key 0 # This file is secret user nobody group nogroup log-append openvpn.log iptables config sudo iptables -A INPUT -i tap0 -j ACCEPT sudo iptables -A INPUT -i br0 -j ACCEPT sudo iptables -A FORWARD -i br0 -j ACCEPT sudo iptables -t nat -A POSTROUTING -s W.X.Y.0/24 -o eth0 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward Routing Tables added route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface W.X.Y.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 0.0.0.0 W.X.Y.1 0.0.0.0 UG 0 0 0 br0 C:>route print =========================================================================== Interface List 32...00 ff ac d6 f7 04 ......TAP-Win32 Adapter V9 15...00 14 d1 e9 57 49 ......Microsoft Virtual WiFi Miniport Adapter #2 14...00 14 d1 e9 57 49 ......Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Net work Adapter 10...00 1f d0 50 1b ca ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 17...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 18...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 36...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.2.1 10.1.2.201 25 10.1.2.0 255.255.255.0 On-link 10.1.2.201 281 10.1.2.201 255.255.255.255 On-link 10.1.2.201 281 10.1.2.255 255.255.255.255 On-link 10.1.2.201 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.2.201 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.2.201 281 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.1.2.1 Default =========================================================================== C:>tracert google.com Tracing route to google.com [74.125.71.147] over a maximum of 30 hops: 1 344 ms 345 ms 343 ms PC [W.X.Y.221] 2 * * * Request timed out.

  Read the article

• svnserve accepts only local connection

  - by stiv

  I've installed svnserve in linux box konrad. On konrad I can checkout from svn: steve@konrad:~$ svn co svn://konrad A konrad/build.xml On my local Windows pc i can ping konrad, but checkout doesn work: C:\Projects>svn co svn://konrad svn: E730061: Unable to connect to a repository at URL 'svn://konrad' svn: E730061: Can't connect to host 'konrad': ??????????? ?? ???????????, ?.?. ???????? ????????? ?????? ?????? ?? ???????????. My linux firewall is disabled: konrad# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination and windows firewall is also off (I can't send screen shot here, so believe me). How can I fix that? Any ideas?

  Read the article

• Mandatory Profiles on a Server 2003 TS Box

  - by Chloe

  I have a Windows Server 2003 box which will be acting as a terminal server. It will actually be running Citrix, but I don't believe that to be relevant here. There has been a request for every user to use a single mandatory profile. I've used mandatory profiles before, but there have been generally different profiles for different users so I've always used the "Terminal Services Profile" tab to good effect. What I'd like this time is a single setting, such as a Group Policy or similar that simply forces every non-domain admin user logging on to the box into using the mandatory profile. We'll be using Folder Redirection to take care of everything else. I'm aware of the following GPO: Computer Policy\Computer Configuration\Administrative Templates\Windows Components/Terminal Services Set path for TS Roaming Profiles But, as that's a computer policy, will it not apply to all users including administrators? If so, is it possible to exclude admins somehow?

  Read the article

• failing to achive tunneling to fresh ubuntu 10.04 server

  - by user65297

  I've just set up a new 10.04 server and can't get the tunneling to work. local machine > ssh -L 9090:localhost:9090 [email protected] login success, but thereafter trying tunnel from local browser, http://127.0.0.1:9090 echo at server terminal: channel 3: open failed: connect failed: Connection refused auth.log sshd[24502]: error: connect_to localhost port 9090: failed. iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Trying 9090 at server (links http://xx.xxx.xx.xx:9090 works) sshd_config is identical to previous 8.04 server, working fine. What's going on? Thankful for any input. Regards, //t

  Read the article

• SVN Server not responding

  - by Rob Forrest

  I've been bashing my head against a wall with this one all day and I would greatly appreciate a few more eyes on the problem at hand. We have an in-house SVN Server that contains all live and development code for our website. Our live server can connect to this and get updates from the repository. This was all working fine until we migrated the SVN Server from a physical machine to a vSphere VM. Now, for some reason that continues to fathom me, we can no longer connect to the SVN Server. The SVN Server runs CentOS 6.2, Apache and SVN 1.7.2. SELinux is well and trully disabled and the problem remains when iptables is stopped. Our production server does run an older version of CentOS and SVN but the same system worked previously so I don't think that this is the issue. Of note, if I have iptables enabled, using service iptables status, I can see a single packet coming in and being accepted but the production server simply hangs on any svn command. If I give up waiting and do a CTRL-C to break the process I get a "could not connect to server". To me it appears to be something to do with the SVN Server rejecting external connections but I have no idea how this would happen. Any thoughts on what I can try from here? Thanks, Rob Edit: Network topology Production server sits externally to our in-house SVN server. Our IPCop (?) firewall allows connections from it (and it alone) on port 80 and passes the connection to the SVN Server. The hardware is all pretty decent and I don't doubt that its doing its job correctly, especially as iptables is seeing the new connections. subversion.conf (in /etc/httpd/conf.d) LoadModule dav_svn_module modules/mod_dav_svn.so <Location /repos> DAV svn SVNPath /var/svn/repos <LimitExcept PROPFIND OPTIONS REPORT> AuthType Basic AuthName "SVN Server" AuthUserFile /var/svn/svn-auth Require valid-user </LimitExcept> </Location> ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:5F:C8:3A inet addr:172.16.0.14 Bcast:172.16.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe5f:c83a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32317 errors:0 dropped:0 overruns:0 frame:0 TX packets:632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2544036 (2.4 MiB) TX bytes:143207 (139.8 KiB) netstat -lntp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 1484/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1135/rpcbind tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1351/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 1230/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 1575/master tcp 0 0 0.0.0.0:58401 0.0.0.0:* LISTEN 1153/rpc.statd tcp 0 0 0.0.0.0:5672 0.0.0.0:* LISTEN 1626/qpidd tcp 0 0 :::139 :::* LISTEN 1678/smbd tcp 0 0 :::111 :::* LISTEN 1135/rpcbind tcp 0 0 :::80 :::* LISTEN 1615/httpd tcp 0 0 :::22 :::* LISTEN 1351/sshd tcp 0 0 ::1:631 :::* LISTEN 1230/cupsd tcp 0 0 ::1:25 :::* LISTEN 1575/master tcp 0 0 :::445 :::* LISTEN 1678/smbd tcp 0 0 :::56799 :::* LISTEN 1153/rpc.statd iptables --list -v -n (when iptables is stopped) Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination iptables --list -v -n (when iptables is running, after one attempted svn connection) Chain INPUT (policy ACCEPT 68 packets, 6561 bytes) pkts bytes target prot opt in out source destination 19 1304 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 1 60 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:80 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 17 packets, 1612 bytes) pkts bytes target prot opt in out source destination tcpdump 17:08:18.455114 IP 'production server'.43255 > 'svn server'.local.http: Flags [S], seq 3200354543, win 5840, options [mss 1380,sackOK,TS val 2011458346 ecr 0,nop,wscale 7], length 0 17:08:18.455169 IP 'svn server'.local.http > 'production server'.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 816478 ecr 2011449346,nop,wscale 7], length 0 17:08:19.655317 IP 'svn server'.local.http > 'production server'k.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 817679 ecr 2011449346,nop,wscale 7], length 0

  Read the article

• disable RADIUS for Cisco 2500 wireless controller

  - by Tim Vaughan

  I have a Cisco 2500 wireless controller and four lightweight access points. I want to use the controller to manage a wireless network secured by WPA only, without using RADIUS or anything else. We'll handle the authentication using a captive portal behind the access points. However, it seems like the controller's default security policy requires a RADIUS server and I can't find out how to switch the policy off. The documentation assumes I'm in an environment which needs heavy-duty security and the use case is actually a small charity/business with much less stringent security requirements. How do I disable the complicated security policy and instead run a simple one that just uses WPA?

  Read the article

• OpenVPN and PPTP on XEN VPS

  - by amiv

  I have Debian based system (Ubuntu 11.10) on XEN VPS. I've installed OpenVPN and works great. I need to install PPTP too, so did it and clients can connect, but they have no internet on client side. If I connect to VPN over PPTP I can ping and access to only my VPS by its IP, but ony that. There's no "internet" on client side. It looks it's not DNS problems (I'm using 8.8.8.8) because I can't ping known IPs. I bet the solution is simple, but don't have any idea. Any guess? /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip 46.38.xx.xx remoteip 10.1.0.1-10 /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 proxyarp nodefaultroute lock nobsdcomp /etc/ppp/ip-up [...] ifconfig ppp0 mtu 1400 /etc/sysctl.conf [...] net.ipv4.ip_forward=1 Command which I run: iptables -t nat -A POSTROUTING -j SNAT --to-source 46.38.xx.xx (IP of my VPS) The client can connect, first one gets IP 10.1.0.1 and DNS from Google. I bet it's iptables problem, am I right? I'm iptables noob and I don't have idea what's wrong. And here's the ifconfig and route command before client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22671 errors:0 dropped:81 overruns:0 frame:0 TX packets:2266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1813358 (1.8 MB) TX bytes:667626 (667.6 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10778 (10.7 KB) TX bytes:10778 (10.7 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And here's the ifconfig and route command after client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.1.0.1 * 255.255.255.255 UH 0 0 0 ppp0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22989 errors:0 dropped:82 overruns:0 frame:0 TX packets:2352 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1841310 (1.8 MB) TX bytes:678456 (678.4 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12102 (12.1 KB) TX bytes:12102 (12.1 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:46.38.xx.xx P-t-P:10.1.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:66 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:10028 (10.0 KB) TX bytes:660 (660.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And ugly iptables --list output: root@vps3780:~# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- 10.1.0.0/24 anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.1.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable And ugly iptables -t nat -L output: root@vps3780:~# iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- 10.1.0.0/24 anywhere SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere SNAT all -- anywhere anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere As I said - OpenVPN works very good. 10.8.0.0/24 for OpenVPN (on tun0). PPTP won't work. 10.1.0.0/24 for PPTP (on ppp0). Clients can connect, but they haven't "internet". Any suggestions will be appreciated. Second whole day fighting with no results. EDIT: iptables -t filter -F - it resolved my problem :-)

  Read the article

• Amazon EC2 - Unable to connect to MySQL

  - by alexus

  I'm having issue connecting from one VM to another # nmap -p3306 ip-XX-XX-XX-XX.ec2.internal Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-10 17:50 EDT Nmap scan report for ip-XX-XX-XX-XX.ec2.internal (XX.XX.XX.XX) Host is up (0.000033s latency). PORT STATE SERVICE 3306/tcp closed mysql Nmap done: 1 IP address (1 host up) scanned in 1.05 seconds # in my Security Group I allowed Inbound connectivity via port TCP, portrange 3306 and Source 0.0.0.0/0, so theoratically it should work, but in reality it doesn't( I'm running red hat enterprise linux 7 on both VMs. mariadb.service running fine on another VM and I am able to connect to it locally. DB's: # netstat -anp | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 2324/mysqld # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # Any ideas what else I missed?

  Read the article

• Permission to see the expandable list of ISA Server 2006

  - by Hossein Mobasher

  I am working on ISA Server 2006 in Windows Server. I want to add some policy rules to my server, I followed this link. But It points to In the Microsoft Internet Security and Acceleration Server 2006 management console, expand the array name, and then click the Firewall Policy node. When I open the ISA Server 2006 Management Console, I can not show the expand list, how can I force ISA to show the expandable tree to start Firewall Policy? Could any one please help me to do this ? Note : I have administrator permission for my account. Thanks in advance :)

  Read the article

• AWS:EC2:: Could not connect FTP client?

  - by heathub

  My Server OS: Amazon Linux I am trying to set up ftp. I have: Installed vsftpd open port 20-21 open port 1024 - 1048 Basically, I followed every of these steps Start vsftpd service (the status indicate [ok]) I use filezilla for my ftp client. Here is my setting/configuration: Host: ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Port: -(blank, but I have tried 20 and 21 though) Server Type: FTP - File Transder Protocol Logon Type: Normal Username: (tried root and ec2-user) Transfer mode: Tried passive and active I always has this error: Status: Waiting to retry... Status: Resolving address of ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Status: Connecting to XX.XX.XXX.XX:21... Error: Connection timed out Error: Could not connect to server Have I missed any configuration/settings? EDIT After execute the /sbin/iptables -L -n Here is the result: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• CentOS 6 - iptables preventing web access via port 80

  - by bsod99

  I'm setting up a new web server with CentOS 6.2 and am not able to connect via the web. Everything looks set up correctly in httpd.conf and Apache is running, so I'm assuming it's an iptables issue. Is there anything in the following which could be causing the issue? # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT)

  Read the article

• Firewall still blocking port 53 despite listing otherwise?

  - by Tom

  I have 3 nodes with virtually the same iptables rules loaded from a bash script, but one particular node is blocking traffic on port 53 despite listing it's accepting it: $ iptables --list -v Chain INPUT (policy DROP 8886 packets, 657K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo any anywhere anywhere 2 122 ACCEPT icmp -- any any anywhere anywhere icmp echo-request 20738 5600K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- eth1 any anywhere node1.com multiport dports http,smtp 0 0 ACCEPT udp -- eth1 any anywhere ns.node1.com udp dpt:domain 0 0 ACCEPT tcp -- eth1 any anywhere ns.node1.com tcp dpt:domain 0 0 ACCEPT all -- eth0 any node2.backend anywhere 21 1260 ACCEPT all -- eth0 any node3.backend anywhere 0 0 ACCEPT all -- eth0 any node4.backend anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 15804 packets, 26M bytes) pkts bytes target prot opt in out source destination nmap -sV -p 53 ns.node1.com // From remote server Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2011-02-24 11:44 EST Interesting ports on ns.node1.com (1.2.3.4): PORT STATE SERVICE VERSION 53/tcp filtered domain Nmap finished: 1 IP address (1 host up) scanned in 0.336 seconds Any ideas? Thanks

  Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >