Search Results

Search found 11015 results on 441 pages for 'explain plan'.

Page 333/441 | < Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >

• How to set shmall, shmmax, shmni, etc ... in general and for postgresql

  - by jpic

  I've used the documentation from PostgreSQL to set it for example this config: >>> cat /proc/meminfo MemTotal: 16345480 kB MemFree: 1770128 kB Buffers: 382184 kB Cached: 10432632 kB SwapCached: 0 kB Active: 9228324 kB Inactive: 4621264 kB Active(anon): 7019996 kB Inactive(anon): 548528 kB Active(file): 2208328 kB Inactive(file): 4072736 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 3432 kB Writeback: 0 kB AnonPages: 3034588 kB Mapped: 4243720 kB Shmem: 4533752 kB Slab: 481728 kB SReclaimable: 440712 kB SUnreclaim: 41016 kB KernelStack: 1776 kB PageTables: 39208 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 8172740 kB Committed_AS: 14935216 kB VmallocTotal: 34359738367 kB VmallocUsed: 399340 kB VmallocChunk: 34359334908 kB HardwareCorrupted: 0 kB AnonHugePages: 456704 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 12288 kB DirectMap2M: 16680960 kB >>> ipcs -l ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 4316816 max total shared memory (kbytes) = 4316816 min seg size (bytes) = 1 ------ Semaphore Limits -------- max number of arrays = 128 max semaphores per array = 250 max semaphores system wide = 32000 max ops per semop call = 32 semaphore max value = 32767 ------ Messages Limits -------- max queues system wide = 31918 max size of message (bytes) = 8192 default max size of queue (bytes) = 16384 sysctl.conf extract: kernel.shmall = 1079204 kernel.shmmax = 4420419584 postgresql.conf non defaults: max_connections = 60 # (change requires restart) shared_buffers = 4GB # min 128kB work_mem = 4MB # min 64kB wal_sync_method = open_sync # the default is the first option checkpoint_segments = 16 # in logfile segments, min 1, 16MB each checkpoint_completion_target = 0.9 # checkpoint target duration, 0.0 - 1.0 effective_cache_size = 6GB Is this appropriate ? If not (or not necessarily), in which case would it be appropriate ? We did note nice performance improvements with this config, how would you improve it ? How should kernel memory management parameters be set ? Can anybody explain how to really set them from the ground up ?

  Read the article

• QoS basics on a Cisco ASA

  - by qbn

  Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

  Read the article

• Unexplained CPU and Disk activity spikes in SQL Server 2005

  - by Philip Goh

  Before I pose my question, please allow me to describe the situation. I have a database server, with a number of tables. Two of the biggest tables contain over 800k rows each. The majority of rows are less than 10k in size, though roughly 1 in 100 rows will be 1 MB but <4 MB. So out of the 1.6 million rows, about 16000 of them will be these large rows. The reason they are this big is because we're storing zip files binary blobs in the database, but I'm digressing. We have a service that runs constantly in the background, trimming 10 rows from each of these 2 tables. In the performance monitor graph above, these are the little bumps (red for CPU, green for disk queue). Once ever minute we get a large spike of CPU activity together with a jump in disk activity, indicated by the red arrow in the screenshot. I've run the SQL Server profiler, and there is nothing that jumps out as a candidate that would explain this spike. My suspicion is that this spike occurs when one of the large rows gets deleted. I've fed the results of the profiler into the tuning wizard, and I get no optimisation recommendations (i.e. I assume this means my database is indexed correctly for my current workload). I'm not overly worried as the server is coping fine in all circumstances, even under peak load. However, I would like to know if there is anything else I can do to find out what is causing this spike? Update: After investigating this some more, the CPU and disk usage spike was down to SQL server's automatic checkpoint. The database uses the simple recovery model, and this truncates the log file at each checkpoint. We can see this demonstrated in the following graph. As described on MSDN, the checkpoints will occur when the transaction log becomes 70% full and we are using the simple recovery model. This has been enlightening and I've definitely learned something!

  Read the article

• Laptop Asus P50IJ with Intel 4500M GMA output going to a Dell 1907FP external monitor will not allow

  - by ProfessionalAmateur

  Hello - I just purchased an Asus P50IJ-X2 laptop which has a Intel GMA 4500M video card running Windows7. At work I output this laptop to a Dell 1907FP LCD which has a maximum resolution of 1280x1024. Not matter what I do the Windows will not allow the laptop to set a resolution higher than 1024x768 to this LCD monitor. Ive even gone to the extent of downloading PowerStrip (I'd post a link but Im new and can only enter 1 url, if you google for powerstrip its the first option) to create a custom driver for my monitor thinking Windows was having a hard time seeing the available resolutions it would accept. However, powerstrip read the registery and properly sees the monitor and what its capable of so Im now at a complete loss as to why Windows7 will not allow me to set/use a 1280x1024 resolution for this external monitor (as my last laptop did running Vista). The Intel documentation (http://software.intel.com/en-us/articles/quick-reference-guide-to-intel-integrated-graphics/) indicates that the GMA 4500M should be able to run up to a 2560x1600 max res. The Dell 1907FP specification states it can run up to a 1280x1024 res. But no matter what the computer will not allow me to set higher than a 1024x768. I'm completely baffled but I would really like to be able to output this laptop to a reasonable resolution, 1024x768 makes me feel like I'm using my mom's computer. Any help would be greatly appreciated! Here are some attached images (I apologize for the links, being new I cannot post images) that should help explain this better: Image 1 - This image is from powerstrip which shows the monitors max accepted resolution and at the top right the max res my PC currently allows. (http://imgur.com/agrno.png) Image 2 - This shows my Windows7 resolution picker. (http://imgur.com/3nv6q.png) Image 3 - The 'List all modes' option taken from the Screen Resolution Advanced Settings List All Modes. (http://imgur.com/AMREh.png) Image 4 - Monitor information from registry read by powerstrip, this shows the laptop is able to read the necessary info from the LCD monitor. (http://imgur.com/hUX4D.png)

  Read the article

• Wifi as LAN - Is it possible ? How ?

  - by sagar

  Hello ! Every one. I am having a query regarding WiFi network. I am having PC & LapTop. Now, Let me explain the situation. I requested My WiFi providers that I want connection in my PC. So that - WiFi provider set up an Antenna on my building Terrace - They joined a cable to pc & that Antenna. ( I think using RJ45 connector ) - The reason behind this - my pc is not having inbuilt wifi functionality. Now - almost laptops have inbuilt functionality. Now - On terrace there is wifi with superb speed. But on my flat - wifi comes with low speed. so, when ever I use internet on my pc - it has great speed - but my laptop works with low speed. The reason behind this - PC is catching wifi from terrace & laptop is catching the wifi from it's own place. Now, My question is something like this. Can we place an antenna or something like that & connect it to laptop for better wifi speed? ( I am not technical person - Please add comment for down vote - if any ) ( Please add comment for more explanation of my Problem ) Thanks in advance for sharing your knowledge. Sagar

  Read the article

• Wifi as LAN - Is it possible ? How ?

  - by sagar

  Hello ! Every one. I am having a query regarding WiFi network. I am having PC & LapTop. Now, Let me explain the situation. I requested My WiFi providers that I want connection in my PC. So that - WiFi provider set up an Antenna on my building Terrace - They joined a cable to pc & that Antenna. ( I think using RJ45 connector ) - The reason behind this - my pc is not having inbuilt wifi functionality. Now - almost laptops have inbuilt functionality. Now - On terrace there is wifi with superb speed. But on my flat - wifi comes with low speed. so, when ever I use internet on my pc - it has great speed - but my laptop works with low speed. The reason behind this - PC is catching wifi from terrace & laptop is catching the wifi from it's own place. Now, My question is something like this. Can we place an antenna or something like that & connect it to laptop for better wifi speed? ( I am not technical person - Please add comment for down vote - if any ) ( Please add comment for more explanation of my Problem ) Thanks in advance for sharing your knowledge. Sagar

  Read the article

• Ubuntu/Nvidia lists DVI dual cable as single

  - by Joseph Mastey

  I have an NVidia Quadro FX 880M graphics card, from which I am trying to drive 2 monitors: my internal laptop montior (15.6", 1920x1080, Nvidia driver says it's running via DisplayPort) and an external 27" monitor (Dell U2711, 2560x1440 native resolution, via DVI). I've hooked the dual DVI cable to the dual DVI port on my dock (Dell PR03X) and installed the proprietary NVidia driver, but I cannot seem to get the full 2560x1440 out of the larger 27" external monitor. Looking at the NVidia driver settings, the monitor's connection is reported as a single DVI cable, rather than a dual one, which would explain the reduced resolution. Does anyone have any experience with an issue like this? What can I do to make full use of my new monitor? (Possibly) Relevant Information: There is no DVI port on the laptop itself, but one is provided via the dock. The laptop and dock both provide a DisplayPort jack, but I have been unable to get this working on either w/ the monitor. I did have the nouveau driver installed when I installed the nvidia proprietary driver, but have since removed it (no change in the monitor situation when I removed it). The 27" reports a max resolution of 1680x1050. Thanks, Joe

  Read the article

• What is causing random hard freezes on my system? Kaspersky?

  - by Christian Ivicevic

  The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

  Read the article

• Cisco ASA intermittently fails to see traffic

  - by DrStalker

  users | Mikrotik -- Internet | ASA | ServerA and ServerB I'm trying to troubleshoot a problem with a new Cisco ASA 5505. The network design is as above - the Microtik is the existing router, ServerA and ServerB used to plug directly into it. ServerA has IP 10.30.1.10, ServerB has IP 10.30.1.11 The ASA is configured with no NAT, a "allow anything" firewall, and uses the microtik as its default gateway. In effect, it is currently a simple IP router; the firewall and VPN stuff will all come later once the basics are working. Th problem is access to ServerA and ServerB is erratic - sometimes it will work, sometimes it will fail. It can fail for either one of the servers only, or both. When it is working: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show the incoming connections. When it is failing: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show nothing reaching the ASA. This can fail for one server only (e.g.: the Mikrotik is putting out packets to 10.30.1.10 and 10.30.1.11, but the ASA is only seeing packets arrive destined for 10.30.1.11) It can fail for one source only (e.g.: ClientA on the users network can ping 10.30.1.11, but clientB cannot) The problem can also be seen from the mikrotik router itself; sometimes it can ping ServerA and ServerB, sometimes it can only ping one of them What could be causing this? I can't think of any possible cause that is intermittent and could explain why the problem may occur for one destination server and not others. edit: Link to ASA config

  Read the article

• nmap on my webserver shows TCP ports 554 and 7070 open

  - by atc

  I have a webserver that hosts various websites for me. The two services that are accessible outside are SSH and Apache2. These are running on a non-standard and standard port, respectively. All other ports are closed explicitly via arno-iptables-firewall. The host is running Debian Testing. I noticed that a scan of the host using nmap produced different results from different PCs. From my laptop on my home network (behind a BT Homehub), I get the following: Not shown: 996 filtered ports PORT STATE SERVICE 80/tcp open http 554/tcp open rtsp 7070/tcp open realserver 9000/tcp open cslistener whereas scanning from a US-based server with nmap 5.00 and a Linux box in Norway running nmap 5.21 I get the following: Not shown: 998 filtered ports PORT STATE SERVICE 80/tcp open http 9000/tcp open cslistener so I hope it's my internal network or ISP that's playing up, but I cannot be sure. Running a netstat -l | grep 7070 produces nothing. Similarly for port 554. Can anyone explain the peculiarities I'm seeing?

  Read the article

• Giving Select Windows Domain Users Symbolic Link Privilege

  - by fp0n

  I would like to setup select users on our domain to have the ability to create symbolic links on local NTFS drives and network shares without needing to run as Administrator, as part of an application with will call the CreateSymbolicLink() API directly. The default configuration for our users is to be Administrator of their computer and I think I am fighting UAC to make the privileges work the way that I want because of that. I found this link on MSDN: http://social.msdn.microsoft.com/Forums/en-SG/windowssdk/thread/fa504848-a5ea-4e84-99b7-0eb4e469cbef which describes the interaction between the SeCreateSymbolicLinkPrivilege, UAC and a domain but really does not have a solution. Here's the three options I've come up with: 1) Create a new group, give the SeCreateSymbolicLinkPrivilege to the group and assign users to the group 2) Give each individual user (2 now, more later) the privilege 3) Give the privilege to the default User group which opens it up to all Users 4) Change config so Users are not Admins by default (probably would work but not likely) Based on my testing, only 3 works for me and that is the least desirable but I've only got a local server to test with, not a domain. I need to recommend to the admin how to set this up and also have something that we can easily explain to other users of our application that are on their own domain or not on a domain. The other option seems to be to create a Service that runs with a SYSTEM account that creates the links for the application but I'd rather not go that route. Thanks.

  Read the article

• How do I connect two computers with a LAN cable?

  - by John

  I have two machines - Windows XP and a laptop using Windows 7. I connected them with a WLAN cable. On the Windows XP machine, I set the IP address to 192.168.0.10. On the Windows 7 laptop, I set the IP address to 192.168.0.20. The laptop can see the Windows XP machine, but Windows XP machine cannot see the Windows 7 machine. But this does NOT concern me. I want to move the files from my desktop (Windows XP) to Windows 7 (laptop). That's why I'm going through all this. The problem is that when I try to connect from Windows 7 to Windows XP machine, I get this window: I don't understand what username/password is needed. I use none on the Windows XP machine. I tried all usernames - no success. Please explain in deep details how to solve my problem so I can connect to my Windows XP machine. EDIT: Maybe this can help: the Windows XP machine is named 'I' and '???????? III' is the name of the laptop. Both computers share one workgroup - WORKGROUP.

  Read the article

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• Using the RST3 plugin in the Leo Outliner

  - by T-Boy

  I'm currently trying out the Leo Outliner, and I've heard quite a bit about the RST3 plugin that it has. I'm not planning to use Leo to program just yet -- at this point I'm wondering if it might be useful for generating HTML and PDF documents, as I'm quite currently enamored with RST and how it works. I'm using my Ubuntu Netbook Remix netbook (running 9.10, I believe). I think I've got it down pat, more or less -- I've installed docutils using the Synaptics Package Manager, and I think I've gotten SilverCity installed, as per the requirements -- I've downloaded the archive, and then run "sudo python setup.py install" with no errors. The thing is, I'm not exactly sure how to invoke the rst3 plugin itself. It doesn't appear in the Plugins menu for Leo right now, and the documentation I've managed to source doesn't seem to clearly explain how to use the plugin. Has anyone had any experience in using the rst3 plugin in Leo? It's a little confusing right now, and searches on Google doesn't seem to be helping much any more. I'm using the latest 4.7.1 final version of Leo from the Synaptics Package Manager (was informed that this would have offered the best integration with UNR, so I figured, what the heck). Have I missed out on any steps here, and are there any useful tutorials on how to use the rst3 plugin?

  Read the article

• Performance of file operations on thousands of files on NTFS vs HFS, ext3, others

  - by peterjmag

  [Crossposted from my Ask HN post. Feel free to close it if the question's too broad for superuser.] This is something I've been curious about for years, but I've never found any good discussions on the topic. Of course, my Google-fu might just be failing me... I often deal with projects involving thousands of relatively small files. This means that I'm frequently performing operations on all of those files or a large subset of them—copying the project folder elsewhere, deleting a bunch of temporary files, etc. Of all the machines I've worked on over the years, I've noticed that NTFS handles these tasks consistently slower than HFS on a Mac or ext3/ext4 on a Linux box. However, as far as I can tell, the raw throughput isn't actually slower on NTFS (at least not significantly), but the delay between each individual file is just a tiny bit longer. That little delay really adds up for thousands of files. (Side note: From what I've read, this is one of the reasons git is such a pain on Windows, since it relies so heavily on the file system for its object database.) Granted, my evidence is merely anecdotal—I don't currently have any real performance numbers, but it's something that I'd love to test further (perhaps with a Mac dual-booting into Windows). Still, my geekiness insists that someone out there already has. Can anyone explain this, or perhaps point me in the right direction to research it further myself?

  Read the article

• SQL Server transaction log backups,

  - by krimerd

  Hi there, I have a question regarding the transaction log backups in sql server 2008. I am currently taking full backups once a week (Sunday) and transaction log backups daily. I put full backup in folder1 on Sunday and then on Monday I also put the 1st transaction log backup in the same folder. On tuesday, before I take the 2nd transaction log backup I move the first transaction log backup from folder1 an put it into folder2 and then I take the 2nd transaction log backup and put it in the folder1. Same thing on Wed, Thurs and so on. Basicaly in folder1 I always have the latest full backup and the latest transaction log backup while the other transaction log backups are in folder2. My questions is, when sql server is about to take, lets say 4th (Thursday) transaction log backup, does it look for the previous transac log backups (1st, 2nd, and 3rd) so that this new backup will only include the transactions from the last backup or it has some other way of knowing whether there are other transac log backups. Basically, I am asking this because all my transaction log backups seem to be about the same size and I thought that their size will depend on the amount of transactions since the last transaction log backup. Example: If you have a, lets say, full backup and then you take a transac log backup and this transac log backup is lets say 200 MB and now you immediatelly take another transac log backup, this last transac log backup should be considerably smaller than the first one because no or almost no transaction occured between these two backups, right? At least, that's what I've been assuming. What happens in my case is that this second backup is pretty much the same size as the first one and I am wondering if the reason for that is because I moved the first transac log backup to a different folder so now sql server thinks that all I have is just a full backup and it then gets all the transactions that happened since the full backup and puts it in the 2nd transac log backup. Can anyone please explain if my assumptions are right? Thanks...

  Read the article

• Can a wifi AP act as a client, and a server at the same time?

  - by nbolton

  I feel this is SF worthy (as opposed to SU) as I go into a bit of detail on gateways/routing. Here's my ideal setup (if possible) -- there is a wifi network (lets call it bob's) with which I want access to, but I have a few other computers on my network which I want to keep behind a firewall. So I was thinking of buying a wireless access point so that I could set it up to connect to bob's network from the AP, and then from my server, connect to the AP via ethernet. So that's the first bit. Second part is that I want to have my own private wifi network off the back of this; can I then tell the AP to serve a new network called foobar. When I say private network, I mean that my server is actually a Debian linux install with routing configured (and I also do some QoS stuff on, etc). So ideally, I'd like all the clients on the private network to be behind the server in terms of routing. However, if the private clients connect to the server via wifi, then aren't they exposed to the "public" network? That is, if someone is savvy enough to scan for my IP range. Also, to do routing I'd need to connect two ethernet cables between the server and the AP (because you can't do routing/QoS on virtual devices) -- which isn't a problem really; but I'm not sure whether the AP will allow me to separate the public and private LANs. Or, as well as the AP, am I better getting a wifi-to-ethernet adapter for the server? I could use a wifi usb, but this can be tricky to set up on headless linux; plus the signal strength is a bit lousy. If this question is a bit vague/spurious in places, please comment and I will explain in more detail.

  Read the article

• How come the ls command prints in multiple columns on tty but only one column everywhere else?

  - by David Lou

  Even after using Unix-like OSes for a couple years, this behaviour still baffles me. When I use the ls command in a directory that has lots of files, the output is usually nicely formatted into multiple columns. Here's an example: $ ls a.txt C.txt f.txt H.txt k.txt M.txt p.txt R.txt u.txt W.txt z.txt A.txt d.txt F.txt i.txt K.txt n.txt P.txt s.txt U.txt x.txt Z.txt b.txt D.txt g.txt I.txt l.txt N.txt q.txt S.txt v.txt X.txt B.txt e.txt G.txt j.txt L.txt o.txt Q.txt t.txt V.txt y.txt c.txt E.txt h.txt J.txt m.txt O.txt r.txt T.txt w.txt Y.txt However, if I try to redirect the output to a file, or pipe it to another command, only a single column appears in the output. Using the same example directory as above, here's what I get when I pipe ls to wc: $ ls | wc 52 52 312 In other words, wc thinks there are 52 lines, even though the output to the terminal has only 5. I haven't observed this behaviour in any other command. Would you like to explain this to me?

  Read the article

• Windows 2008 RemoteAPP client disconnects within a matter of minutes

  - by Jeroen Wilke

  I'm having an odd problem with Windows 2008 TS, and remote applications specifically. The situation is as follows: TS idle timeout is disabled via GPO TS terminating disconnected sessions after 1hr (via GPO) My users can log on to the Terminal server, and get a full desktop, OR via rdp files that give access to a few remote applications. When a user connects to a full desktop, everything is fine and dandy, they will remain logged on indefinately, and when they disconnect the session is terminated after an hour. however, when a user connects using a remote application link, the client seems to disconnect after only a few minutes of inactivity, when you click the window, the session reconnects. EventID's on TS server: 4779: This event is generated when a user disconnects from an existing Terminal Services session, or when a user switches away from an existing destop using Fast User Switching. 4778 : This event is generated when a user reconnects to an existing Terminal Services session, or when a user switches to an existing desktop using Fast User Switching users are connecting directly to 3389, not using a TS-gateway at the moment. This behavior is consistent on different clients that we have, Full desktop is fine, RemoteAPP constantly disconnects. The .rdp file used doesn't list any interesting parameters, aside from what application to launch, and where to find it. Can someone explain to me how there can be a difference in behaviour between full desktop, and remoteapp ? since essentially they use the exact same client ? Regards Jeroen

  Read the article

• prevent IE8 tabs from opening tabs in stack in taskbar

  - by Nano8Blazex

  This may have been asked before too... But, anyways. I'm using Windows 7 Ultimate, and IE 8, and have the taskbar in icon view. I'm not sure how to explain this, but I'm amazed at how each tab in IE8 seems to act like a new "process" in the taskbar (as if each tab was a window). Like... each tab acts like a different window in the taskbar although they are actually running in the same window. Now when I use IE 8 it looks (in the taskbar) like there's 15 windows open when in fact the taskbar is simply showing the 15 tabs. More simply put, it's displaying a "stack" for all of the tabs when I'd rather have the icon act like, for example, firefox so that a stack is only shown for the multiple windows. I know that they are meant to be running as separate processes to prevent crashing and the such... but is there a way to disable this strange "taskbar" effect? I'd rather have the taskbar show the main window and not the tabs individually. There has to be a simple way to do this...

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• How does Subnetting Work?

  - by Kyle Brandt

  How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. What is classless routing and why is class-based routing obsolete? If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? Not looking for links to other sites (unless maybe you have one post with a bunch of good ones). I already know how to subnet, I just thought it would be nice if Server Fault had a generic subnetting answer.

  Read the article

• What DBus signal is sent on system suspend?

  - by Paul Robinson

  Hello, I need to detect when a machine is going to sleep in Ubuntu 9.10 and Fedora 13. Both use UPower, so I've been looking on the "org.freedesktop.UPower" DBus bus for such signals. I've been listening for the "sleeping" signal on the UPower bus with the following command: dbus-monitor --system "type='signal',interface='org.freedesktop.UPower',member='Sleeping'" When I sleep the machine (either by closing the lid, selecting "shutdown - suspend" or sending a DBus message) I don't see a "sleeping" event. I notice that the "Sleeping" event is sent when the "org.freedesktop.UPower.AboutToSleep" method is invoked. I can do this manually by calling: dbus-send --print-reply --system --dest=org.freedesktop.UPower /org/freedesktop/UPower org.freedesktop.UPower.AboutToSleep And I notice the "sleeping" signal is fired. My understanding is that anything that sleeps the PC must send the "AboutToSleep" signal before hand. It doesn't seem like this is happening. I've tried these steps on both Fedora 13 and Ubuntu 9.10 and I see the same results. Can anyone explain what's happening or provide me with an alternative DBus signal to listen for? Many thanks, Paul

  Read the article

• Bash script 'while read' loop causes 'broken pipe' error when run with GNU Parallel

  - by Joe White

  According to the GNU Parallel mailing list this is not a GNU Parallel-specific problem. They suggested that I post my problem here. The error I'm getting is a "broken pipe" error, but I feel I should first explain the context of my problem and what causes this error. It happens when trying to use any bash script containing a 'while read' loop in GNU Parallel. I have a basic bash script like this: #!/bin/bash # linkcheck.sh while read domain do host "$domain" done Assume that I want to pipe in a large list (250mb say). cat urllist | ./linkcheck.sh Running host command on 250mb worth of URLs is rather slow. To speed things up I want to break up the input into chunks before piping it and then run multiple jobs in parallel. GNU Parallel is capable of doing this. cat urllist | parallel --pipe -j0 parallel ./linkcheck.sh {} {} is substituted by the contents of urllist line-by-line. Assume that my systems default setup is capable of running 500ish jobs per instance of parallel. To get round this limitation we can parallelize Parallel itself: cat urllist | parallel -j10 --pipe parallel -j0 ./linkcheck.sh {} This will run 5000'ish jobs. It will also, sadly, cause the error "broken pipe" (bash FAQ). Yet the script starts to work if I remove the while read loop and take input directly from whatever is fed into {} e.g., #!/bin/bash # linkchecker.sh domain="$1" host "$1" Why will it not work with a while read loop? Is it safe to just turn off the SIGPIPE signal to stop the "broken pipe" message, or will that have side effects such as data corruption? Thanks for reading.

  Read the article

• How can i link a oracle user to a business objects user

  - by Robert Speckmann

  I have a problem with linking the oracle user to a business objects user. I will try to explain it as detailed as possible; I have a Oracle database (10g) where a couple of users are defined. These users can query on information with application X. Those records will then be written into the oracle database. The records that is written into the database has a ID that links to the person that has run the query. I also have a active directory in wich a couple of users are made; testuser1, testuser2. When those users log on, and want to load a report in Business Objects XI i want them to see the information that was created when the report was activated by that same user that had runned the query before with application X. The name of the person in the active directory and the name in the oracle database are not the same but i dont think that would be a problem in this stage. So the steps i took: First, i run a report in application X (with a account prodpim_rs) wich fills my Oracle database with a record. The second step is logging on as testuser1 (from the AD) and then login on Business Objects XI with the account. Now i want to load a report with the information in my Oracle database. So the prodpim_rs user and the testuser must have a link between them. I am wondering how to forfill this. Can i link the account, wich is made in a Oracle database, with the user of BO wich is linked to my AD? Thank you in advance for your reply Robert

  Read the article

< Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >