Search Results

Search found 9117 results on 365 pages for 'systems analysis'.

Page 334/365 | < Previous Page | 330 331 332 333 334 335 336 337 338 339 340 341  | Next Page >

• Wrapping a point-to-point link

  - by user3712955

  I'm using a pair of IP radios (non-WiFi) to bridge my office engineering LAN (172.0.0.0/8) to a lab in another building. The radios work fine, but they expose a web management interface I'd like to hide, and they also generate traffic (ARP, STP, and more) that I need to keep off my (very, very clean) LAN segments. I have some ARM-Linux boards (similar to Beagle/Panda/RasPi) running Ubuntu, and I've put one at each end of the link, between the radio and the LAN. Each of the boards has 2 wired Ethernet interfaces, eth0 and eth1. The LAN segments are connected to eth0, and the radios are connected to eth1. I'd like to accomplish the following: Keep radio-originated traffic off my LAN segments! Hide all services provided by the radio (web, ssh, etc.) Transparently pass all traffic between the LAN segments (including things like ARP). The above also applies to the ARM-Linux boards: No stray traffic my LAN from them either! I'd like the system to look like a switch: LAN packets arriving at one eth0 appear at the other. And neither eth0 should have an IP address: The working system should behave like a CAT6 cable with some latency (instead of ARM boards and radios). Unfortunately, I'm confused about how to properly configure the ARM Ubuntu systems. What I'm guessing I need is a bridge on each board (br0?) and a VLAN (vlan0 or eth0.0?) to isolate the LAN traffic from everything else as it passes through the ARM boards and the radios. Then I need some kind of a firewall to block sending anything out eth0 that isn't from the other eth0 (via the VLAN). I've looked at the ip and ebtables commands (especially -t broute). While the concepts sorta-kinda make sense, I'm completely lost in the details. Edit: In the perverse case that a system on one of my LAN segments has the same IP address as one of the radios, or as eth1 on the ARM-Ubuntu boards, a VLAN won't work. Which I believe means I need to tunnel all traffic between the two eth0 interfaces to get that "like a wire" behavior. Help? Finally, I'd like to have a way to temporarily expose services on the ARM boards (ssh) and the radios (web) for maintenance purposes. Ideally, it would expose an IP address with ssh available on port 22. Once connected, I figure I'd start an X11 session and run a browser on the ARM board to access the radios. Or something. I could login via the console to enable/disable this, or perhaps could use a GPIO to trigger a script. I feel I've identified most of the pieces needed to make all this happen, but I have no idea how to combine them to make a working system. Thanks!

  Read the article

• Migrating Split Access Database from one domain to another (not working, details in Q)

  - by Expo_Rob

  Some background: I'm a programmer, not a network administrator, who has been asked to migrate some accounting software (Integrated Office Accounting version 3.2) from an existing domain (OLD_NETWORK) to a new domain (NEW_NETWORK). No-body at the office knows how it works under the hood. It is a split Access 2000 database with the back-end shared and on a file server (which is also the DC) using mapped drives. The DC is NT Server 4 SP 6. The new server is server 2003. The two networks are running independently (ie: two computers on each desk). I have been able to get new computers set up on NEW_NETWORK and working with the IOA software just perfectly but for one problem: The company here uses other entirely separate databases which access the tables IOA maintains (specifically the 'customers' table) via links. To switch between these systems, you press F11 then File-Open the appropriate database and away you go (this is necessary to maintain the permissions that the IOA system uses to protect the customers table). The entire database is Access 2000, the links go to other Access databases, SQL-Server is not involved in any way, nor is a migration to SQL server likely. If I can't migrate anything over, everything will stay as it is, and the NEW_NETWORK computers will not be used. The problem: When I try and update these seperate databases (I shall call one "BANK_ACCOUNT", but the name does not matter), it says "this recordset cannot be updated". It also will sometimes not pull information out of the 'customers' table (ie: date_entered) when looking at a report of everyone who opened a bank account on a certain day (ie: today). I have tried: Giving 'everyone' full control via. shared directory permissions Giving 'everyone' full control on a file system level Checking the permissions within Access (everyone has full read/write on all tables) Copying the entire server contents from one file server to another (ie: xcopy everything) Copying the entire local client files from one computer to another, putting them in the exact same position in the file system, with the same permissons (or full control to 'everyone'). Running as an Administrator Taking one of the NEW_NETWORK computers, having it join OLD_NETWORK and run the software (direct copy from a working system with identical drive mappings), this did not work Weeping openly My Question: Is there anything else I can try? (sorry for this being so long)

  Read the article

• Synapse and string problems with HTTPSend in Delphi 2010

  - by Mick

  I have been trying to get to the bottom of this problem off and on for the past 2 days and I'm really stuck. Hopefully some smart folks can help me out. The issue is that I have a function that I call in a thread that downloads a file (using Synapse libraries) from a website that is passed to it. However, I've found that every once in a while there are sites where it will not pull down a file, but wget or Firefox/IE will download it without issue. Digging into it, I've found some curious things. Here is the relevant code: uses //[..] HTTPSend, blcksock; //[..] type TMyThread = class(TThread) protected procedure Execute; override; private { Private declarations } fTheUrl: string; procedure GetFile(const TheUrl: string); public property thrd_TheUrl: string read fTheUrl write fTheUrl; end; implementation [..] procedure TMyThread.GetFile(const TheUrl: string); var HTTP: THTTPSend; success: boolean; sLocalUrl: string; IsSame : boolean; begin HTTP := THTTPSend.Create; try HTTP.UserAgent := 'Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; .NET CLR 2.0.50727)'; HTTP.ProxyHost := 'MYPROXY.COM'; HTTP.ProxyPort := '80'; sLocalUrl := 'http://web.archive.org/web/20071212205017/energizer.com/usbcharger/download/UsbCharger_setup_V1_1_1.exe'; IsSame := SameText(sLocalUrl, sTheUrl); //this equals True when I debug /// /// /// THIS IS WHERE THE ISSUE BEGINS /// I will comment out 1 of the following when debugging /// HTTP.HTTPMethod('GET', sLocalUrl); // ----this works and WILL download the file HTTP.HTTPMethod('GET', sTheUrl); // --- this always fails, and HTTP.ResultString contains "Not Found" success := SysUtils.UpperCase(HTTP.ResultString) = 'OK'; if HTTP.ResultCode > 0 then success := True; //this is here just to keep the value around while debugging finally HTTP.Free; end; end; procedure TMyThread.Execute begin //fTheURL contains this value: http://web.archive.org/web/20071212205017/energizer.com/usbcharger/download/UsbCharger_setup_V1_1_1.exe GetFile(fTheUrl); end; The problem is that when I assign a local variable to the function and give it the URL directly, everything works. However, when passing the variable into the function, it fails. Anyone have any ideas? HTTP.HTTPMethod('GET', sLocalUrl); // ----this works and WILL download the file HTTP.HTTPMethod('GET', sTheUrl); // --- this always fails, and HTTP.ResultString contains "Not Found" I'm using the latest version of Synapse from their SVN repository (version from 2 days ago). NOTE: The file I am attempting to download is known to have a virus, the program I am writing is meant to download malicious files for analysis. So, don't execute the file once you download it. However, I'm using this URL b/c this is the one I can reproduce the issue with.

  Read the article

• Using MS Standalone profiler in VS2008 Professional

  - by fishdump

  I am trying to profile my .NET dll while running it from VS unit testing tools but I am having problems. I am using the standalone command-line profiler as VS2008 Professional does not come with an inbuilt profiler. I have an open CMD window and have run the following commands (I instrumented it earlier which is why vsinstr gave the warning that it did): C:\...\BusinessRules\obj\Debug>vsperfclrenv /samplegclife /tracegclife /globalsamplegclife /globaltracegclife Enabling VSPerf Sampling Attach Profiling. Allows to 'attaching' to managed applications. Current Profiling Environment variables are: COR_ENABLE_PROFILING=1 COR_PROFILER={0a56a683-003a-41a1-a0ac-0f94c4913c48} COR_LINE_PROFILING=1 COR_GC_PROFILING=2 C:\...\BusinessRules\obj\Debug>vsinstr BusinessRules.dll Microsoft (R) VSInstr Post-Link Instrumentation 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Error VSP1018 : VSInstr does not support processing binaries that are already instrumented. C:\...\BusinessRules\obj\Debug>vsperfcmd /start:trace /output:foo.vsp Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. C:\...\BusinessRules\obj\Debug> I then ran the unit tests that exercised the instrumented code. When the unit tests were complete, I did... C:\...\BusinessRules\obj\Debug>vsperfcmd /shutdown Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Waiting for process 4836 ( C:\Program Files\Microsoft Visual Studio 9.0\Common7\IDE\vstesthost.exe) to shutdown... It was clearly waiting for VS2008 to close so I closed it... Shutting down the Profile Monitor ------------------------------------------------------------ C:\...\BusinessRules\obj\Debug> All looking good, there was a 3.2mb foo.vsp file in the directory. I next did... C:\...\BusinessRules\obj\Debug>vsperfreport foo.vsp /summary:all Microsoft (R) VSPerf Report Generator, Version 9.0.0.0 Copyright (C) Microsoft Corporation. All rights reserved. VSP2340: Environment variables were not properly set during profiling run and managed symbols may not resolve. Please use vsperfclrenv before profiling. File opened Successfully opened the file. A report file, foo_Header.csv, has been generated. A report file, foo_MarksSummary.csv, has been generated. A report file, foo_ProcessSummary.csv, has been generated. A report file, foo_ThreadSummary.csv, has been generated. Analysis completed A report file, foo_FunctionSummary.csv, has been generated. A report file, foo_CallerCalleeSummary.csv, has been generated. A report file, foo_CallTreeSummary.csv, has been generated. A report file, foo_ModuleSummary.csv, has been generated. C:\...\BusinessRules\obj\Debug> Notice the warning about environment variables and using vsperfclrenv? But I had run it! Maybe I used the wrong switches? I don't know. Anyway, loading the csv files into Excel or using the perfconsole tool gives loads of useful info with useless symbol names: *** Loading commands from: C:\temp\PerfConsole\bin\commands\timebytype.dll *** Adding command: timebytype *** Loading commands from: C:\temp\PerfConsole\bin\commands\partition.dll *** Adding command: partition Welcome to PerfConsole 1.0 (for bugs please email: [email protected]), for help type: ?, for a quickstart type: ?? > load foo.vsp *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Profile loaded from 'foo.vsp' into @foo > > functions @foo >>>>> Function Name Exclusive Inclusive Function Name Module Name -------------------- -------------------- -------------- --------------- 900,798,600,000.00 % 900,798,600,000.00 % 0x0600003F 20397910 14,968,500,000.00 % 44,691,540,000.00 % 0x06000040 14736385 8,101,253,000.00 % 14,836,330,000.00 % 0x06000041 5491345 3,216,315,000.00 % 6,876,929,000.00 % 0x06000042 3924533 <snip> 71,449,430.00 % 71,449,430.00 % 0x0A000074 42572 52,914,200.00 % 52,914,200.00 % 0x0A000073 0 14,791.00 % 13,006,010.00 % 0x0A00007B 0 199,177.00 % 6,082,932.00 % 0x2B000001 5350072 2,420,116.00 % 2,420,116.00 % 0x0A00008A 0 836.00 % 451,888.00 % 0x0A000045 0 9,616.00 % 399,436.00 % 0x0A000039 0 18,202.00 % 298,223.00 % 0x06000046 1479900 I am so close to being able to find the bottlenecks, if only it will give me the function and module names instead of hex numbers! What am I doing wrong? --- Alistair.

  Read the article

• MSChart on ASP.NET MVC 2

  - by Adron

  I upgraded my MVC Application using MSChart to MVC 2 and have ended up with broken image links for the charts. See my blog entry here: http://blog.adronbhall.com/post/2010/04/12/MVC-2-Breaks-my-Charts.aspx I get no build errors anymore, and have completed the following steps. First, I setup the following web.config lines. add tagPrefix="asp" namespace="System.Web.UI.DataVisualization.Charting" assembly="System.Web.DataVisualization, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" and add path="ChartImg.axd" verb="GET,HEAD" type="System.Web.UI.DataVisualization.Charting.ChartHttpHandler, System.Web.DataVisualization, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" validate="false" (NOTE: I took the chevrons off so the lines would appear) The next thing I did was create this page with the following code. Which should, according to it working in MVC<1, showed 4 charts. <%@ Page Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage" %> <%@ Import Namespace="Scorecard.Views" %> <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> Scorecard </asp:Content> <asp:Content ID="applicationTitle" ContentPlaceHolderID="ContentPlaceHolderApplicationName" runat="server"> <%=Html.Encode(ViewData["ApplicationTitle"])%> </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> <form id="form1" runat="server"> <h2> Web Analysis Scorecard </h2> <table> <tr> <td> <% ChartHelper chartHelper = new ChartHelper("Top Countries", (double[])ViewData["TopCountryCounts"], (string[])ViewData["TopCountries"], SeriesChartType.Pie); Chart chartPieTwo = chartHelper.ResultingChart; // Explode data point with label "USA" chartPieTwo.Series["DefaultSeries"].Points[3]["Exploded"] = "true"; chartHelper.RenderChart(this); %> </td> <td> <% chartHelper = new ChartHelper("View Cart Trend", (double[])ViewData["LineValues"], (string[])ViewData["TopEngines"], SeriesChartType.Line); chartHelper.RenderChart(this); %> </td> </tr> <tr> <td> <% chartHelper = new ChartHelper("Yesterday's Page Views", (double[])ViewData["ColumnStats"], (string[])ViewData["ColumnStatHeaders"], SeriesChartType.Column); chartHelper.RenderChart(this); %> </td> <td> <% double[] theValues = (double[])ViewData["ColumnStats"]; double[] newValues = new double[] { 0, 0, 0, 0 }; int count = 0; int daysInMonth = DateTime.DaysInMonth(DateTime.Now.Year, DateTime.Now.Month); foreach (double d in theValues) { newValues[count] += d * daysInMonth; count++; } chartHelper = new ChartHelper("Current Month Page Views", newValues, (string[])ViewData["ColumnStatHeaders"], SeriesChartType.Bar); chartHelper.RenderChart(this); %> </td> </tr> </table> </form>

  Read the article

• Psychology researcher wants to learn new language

  - by user273347

  I'm currently considering R, matlab, or python, but I'm open to other options. Could you help me pick the best language for my needs? Here are the criteria I have in mind (not in order): Simple to learn. I don't really have a lot of free time, so I'm looking for something that isn't extremely complicated and/or difficult to pick up. I know some C, FWIW. Good for statistics/psychometrics. I do a ton of statistics and psychometrics analysis. A lot of it is basic stuff that I can do with SPSS, but I'd like to play around with the more advanced stuff too (bootstrapping, genetic programming, data mining, neural nets, modeling, etc). I'm looking for a language/environment that can help me run my simpler analyses faster and give me more options than a canned stat package like SPSS. If it can even make tables for me, then it'll be perfect. I also do a fair bit of experimental psychology. I use a canned experiment "programming" software (SuperLab) to make most of my experiments, but I want to be able to program executable programs that I can run on any computer and that can compile the data from the experiments in a spreadsheet. I know python has psychopy and pyepl and matlab has psychtoolbox, but I don't know which one is best. If R had something like this, I'd probably be sold on R already. I'm looking for something regularly used in academe and industry. Everybody else here (including myself, so far) uses canned stat and experiment programming software. One of the reasons I'm trying to learn a programming language is so that I can keep up when I move to another lab. Looking forward to your comments and suggestions. Thank you all for your kind and informative replies. I appreciate it. It's still a tough choice because of so many strong arguments for each language. Python - Thinking about it, I've forgotten so much about C already (I don't even remember what to do with an array) that it might be better for me to start from scratch with a simple program that does what it's supposed to do. It looks like it can do most of the things I'll need it to do, though not as cleanly as R and MATLAB. R - I'm really liking what I'm reading about R. The packages are perfect for my statistical work now. Given the purpose of R, I don't think it's suited to building psychological experiments though. To clarify, what I mean is making a program that presents visual and auditory stimuli to my specifications (hundreds of them in a preset and/or randomized sequence) and records the response data gathered from participants. MATLAB - It's awesome that cognitive and neuro folk are recommending MATLAB, because I'm preparing for the big leap from social and personality psychology to cognitive neuro. The problem is the Uni where I work doesn't have MATLAB licenses (and 3750 GBP for a compiler license is not an option for me haha). Octave looks like a good alternative. PsychToolbox is compatible with Octave, thankfully. SQL - Thanks for the tip. I'll explore that option, too. Python will be the least backbreaking and most useful in the short term. R is well suited to my current work. MATLAB is well suited to my prospective work. It's a tough call, but I think I am now equipped to make a more well-informed decision about where to go next. Thanks again!

  Read the article

• LLVM JIT segfaults. What am I doing wrong?

  - by bugspy.net

  It is probably something basic because I am just starting to learn LLVM.. The following creates a factorial function and tries to git and execute it (I know the generated func is correct because I was able to static compile and execute it). But I get segmentation fault upon execution of the function (in EE-runFunction(TheF, Args)) #include <iostream> #include "llvm/Module.h" #include "llvm/Function.h" #include "llvm/PassManager.h" #include "llvm/CallingConv.h" #include "llvm/Analysis/Verifier.h" #include "llvm/Assembly/PrintModulePass.h" #include "llvm/Support/IRBuilder.h" #include "llvm/Support/raw_ostream.h" #include "llvm/ExecutionEngine/JIT.h" #include "llvm/ExecutionEngine/GenericValue.h" using namespace llvm; Module* makeLLVMModule() { // Module Construction LLVMContext& ctx = getGlobalContext(); Module* mod = new Module("test", ctx); Constant* c = mod->getOrInsertFunction("fact64", /*ret type*/ IntegerType::get(ctx,64), IntegerType::get(ctx,64), /*varargs terminated with null*/ NULL); Function* fact64 = cast<Function>(c); fact64->setCallingConv(CallingConv::C); /* Arg names */ Function::arg_iterator args = fact64->arg_begin(); Value* x = args++; x->setName("x"); /* Body */ BasicBlock* block = BasicBlock::Create(ctx, "entry", fact64); BasicBlock* xLessThan2Block= BasicBlock::Create(ctx, "xlst2_block", fact64); BasicBlock* elseBlock = BasicBlock::Create(ctx, "else_block", fact64); IRBuilder<> builder(block); Value *One = ConstantInt::get(Type::getInt64Ty(ctx), 1); Value *Two = ConstantInt::get(Type::getInt64Ty(ctx), 2); Value* xLessThan2 = builder.CreateICmpULT(x, Two, "tmp"); //builder.CreateCondBr(xLessThan2, xLessThan2Block, cond_false_2); builder.CreateCondBr(xLessThan2, xLessThan2Block, elseBlock); /* Recursion */ builder.SetInsertPoint(elseBlock); Value* xMinus1 = builder.CreateSub(x, One, "tmp"); std::vector<Value*> args1; args1.push_back(xMinus1); Value* recur_1 = builder.CreateCall(fact64, args1.begin(), args1.end(), "tmp"); Value* retVal = builder.CreateBinOp(Instruction::Mul, x, recur_1, "tmp"); builder.CreateRet(retVal); /* x<2 */ builder.SetInsertPoint(xLessThan2Block); builder.CreateRet(One); return mod; } int main(int argc, char**argv) { long long x; if(argc > 1) x = atol(argv[1]); else x = 4; Module* Mod = makeLLVMModule(); verifyModule(*Mod, PrintMessageAction); PassManager PM; PM.add(createPrintModulePass(&outs())); PM.run(*Mod); // Now we going to create JIT ExecutionEngine *EE = EngineBuilder(Mod).create(); // Call the function with argument x: std::vector<GenericValue> Args(1); Args[0].IntVal = APInt(64, x); Function* TheF = cast<Function>(Mod->getFunction("fact64")) ; /* The following CRASHES.. */ GenericValue GV = EE->runFunction(TheF, Args); outs() << "Result: " << GV.IntVal << "\n"; delete Mod; return 0; }

  Read the article

• Tomcat stops responding to JK requests

  - by Bruno Reis

  Hello. I have a nasty issue with load-balanced Tomcat servers that are hanging up. Any help would be greatly appreciated. The system I'm running Tomcat 6.0.26 on HotSpot Server 14.3-b01 (Java 1.6.0_17-b04) on three servers sitting behind another server that acts as load balancer. The load balancer runs Apache (2.2.8-1) + MOD_JK (1.2.25). All of the servers are running Ubuntu 8.04. The Tomcat's have 2 connectors configured: an AJP one, and a HTTP one. The AJP is to be used with the load balancer, while the HTTP is used by the dev team to directly connect to a chosen server (if we have a reason to do so). I have Lambda Probe 1.7b installed on the Tomcat servers to help me diagnose and fix the problem soon to be described. The problem Here's the problem: after about 1 day the application servers are up, JK Status Manager starts reporting status ERR for, say, Tomcat2. It will simply get stuck on this state, and the only fix I've found so far is to ssh the box and restart Tomcat. I must also mention that JK Status Manager takes a lot longer to refresh when there's a Tomcat server in this state. Finally, the "Busy" count of the stuck Tomcat on JK Status Manager is always high, and won't go down per se -- I must restart the Tomcat server, wait, then reset the worker on JK. Analysis Since I have 2 connectors on each Tomcat (AJP and HTTP), I still can connect to the application through the HTTP one. The application works just fine like this, very, very fast. That is perfectly normal, since I'm the only one using this server (as JK stopped delegating requests to this Tomcat). To try to better understand the problem, I've taken a thread dump from a Tomcat which is not responding anymore, and from another one that has been restarted recently (say, 1 hour before). The instance that is responding normally to JK shows most of the TP-ProcessorXXX threads in "Runnable" state, with the following stack trace: java.net.SocketInputStream.socketRead0 ( native code ) java.net.SocketInputStream.read ( SocketInputStream.java:129 ) java.io.BufferedInputStream.fill ( BufferedInputStream.java:218 ) java.io.BufferedInputStream.read1 ( BufferedInputStream.java:258 ) java.io.BufferedInputStream.read ( BufferedInputStream.java:317 ) org.apache.jk.common.ChannelSocket.read ( ChannelSocket.java:621 ) org.apache.jk.common.ChannelSocket.receive ( ChannelSocket.java:559 ) org.apache.jk.common.ChannelSocket.processConnection ( ChannelSocket.java:686 ) org.apache.jk.common.ChannelSocket$SocketConnection.runIt ( ChannelSocket.java:891 ) org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run ( ThreadPool.java:690 ) java.lang.Thread.run ( Thread.java:619 ) The instance that is stuck show most (all?) of the TP-ProcessorXXX threads in "Waiting" state. These have the following stack trace: java.lang.Object.wait ( native code ) java.lang.Object.wait ( Object.java:485 ) org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run ( ThreadPool.java:662 ) java.lang.Thread.run ( Thread.java:619 ) I don't know of the internals of Tomcat, but I would infer that the "Waiting" threads are simply threads sitting on a thread pool. So, if they are threads waiting inside of a thread pool, why wouldn't Tomcat put them to work on processing requests from JK? Solution? So, as I've stated before, the only fix I've found is to stop the Tomcat instance, stop the JK worker, wait the latter's busy count slowly go down, start Tomcat again, and enable the JK worker once again. What is causing this problem? How should I further investigate it? What can I do to solve it? Thanks in advance.

  Read the article

• Reading email address from contacts fails with weird memory issue - Solved

  - by CapsicumDreams

  Hi all, I'm stumped. I'm trying to get a list of all the email address a person has. I'm using the ABPeoplePickerNavigationController to select the person, which all seems fine. I'm setting my ABRecordRef personDealingWith; from the person argument to - (BOOL)peoplePickerNavigationController:(ABPeoplePickerNavigationController *)peoplePicker shouldContinueAfterSelectingPerson:(ABRecordRef)person property:(ABPropertyID)property identifier:(ABMultiValueIdentifier)identifier { and everything seems fine up till this point. The first time the following code executes, all is well. When subsequently run, I can get issues. First, the code: // following line seems to make the difference (issue 1) // NSLog(@"%d", ABMultiValueGetCount(ABRecordCopyValue(personDealingWith, kABPersonEmailProperty))); // construct array of emails ABMultiValueRef multi = ABRecordCopyValue(personDealingWith, kABPersonEmailProperty); CFIndex emailCount = ABMultiValueGetCount(multi); if (emailCount > 0) { // collect all emails in array for (CFIndex i = 0; i < emailCount; i++) { CFStringRef emailRef = ABMultiValueCopyValueAtIndex(multi, i); [emailArray addObject:(NSString *)emailRef]; CFRelease(emailRef); } } // following line also matters (issue 2) CFRelease(multi); If compiled as written, the are no errors or static analysis problems. This crashes with a *** -[Not A Type retain]: message sent to deallocated instance 0x4e9dc60 error. But wait, there's more! I can fix it in either of two ways. Firstly, I can uncomment the NSLog at the top of the function. I get a leak from the NSLog's ABRecordCopyValue every time through, but the code seems to run fine. Also, I can comment out the CFRelease(multi); at the end, which does exactly the same thing. Static compilation errors, but running code. So without a leak, this function crashes. To prevent a crash, I need to haemorrhage memory. Neither is a great solution. Can anyone point out what's going on? Solution: It turned out that I wasn't storing the ABRecordRef personDealingWith var correctly. I'm still not sure how to do that properly, but instead of having the functionality in another routine (performed later), I'm now doing the grunt-work in the delegate method, and using the derived results at my leisure. The new (working) routine: - (BOOL)peoplePickerNavigationController:(ABPeoplePickerNavigationController *)peoplePicker shouldContinueAfterSelectingPerson:(ABRecordRef)person { // as soon as they select someone, return personDealingWithFullName = (NSString *)ABRecordCopyCompositeName(person); personDealingWithFirstName = (NSString *)ABRecordCopyValue(person, kABPersonFirstNameProperty); // construct array of emails [personDealingWithEmails removeAllObjects]; ABMutableMultiValueRef multi = ABRecordCopyValue(person, kABPersonEmailProperty); if (ABMultiValueGetCount(multi) > 0) { // collect all emails in array for (CFIndex i = 0; i < ABMultiValueGetCount(multi); i++) { CFStringRef emailRef = ABMultiValueCopyValueAtIndex(multi, i); [personDealingWithEmails addObject:(NSString *)emailRef]; CFRelease(emailRef); } } CFRelease(multi); return NO; }

  Read the article

• Postmortem debugging with WinDBG.

  - by Drazar

  I have an WCF-service running on an server, and occasionally(1-2 times every month) it throws an COMException with the informative message ”Unknown error (0x8005008)”. When i googled for this particular error I only got threads about problems when creating virtual directories in IIS. And the source code hasn’t anything with making a virtual directory in IIS. DirectoryServiceLib.LdapProvider.Directory - CreatePost - Could not create employee for 195001010000,000000000000: System.Runtime.InteropServices.COMException (0x80005008): Unknown error (0x80005008) at System.DirectoryServices.PropertyValueCollection.PopulateList I've taken a memorydump when I catch the Exception for further analysis in WinDBG. After switching to the right thread I executed the !CLRStack command: 000000001b8ab6d8 000000007708671a [NDirectMethodFrameStandalone: 000000001b8ab6d8] Common.MemoryDump.MiniDumpWriteDump(IntPtr, Int32, IntPtr, MINIDUMP_TYPE, IntPtr, IntPtr, IntPtr) 000000001b8ab680 000007ff002808d8 DomainBoundILStubClass.IL_STUB_PInvoke(IntPtr, Int32, IntPtr, MINIDUMP_TYPE, IntPtr, IntPtr, IntPtr) 000000001b8ab780 000007ff00280812 Common.MemoryDump.CreateMiniDump(System.String) 000000001b8ab7e0 000007ff0027b218 DirectoryServiceLib.LdapProvider.Directory.CreatePost(System.String, DirectoryServiceLib.Model.Post, DirectoryServiceLib.Model.Presumptions, Services.Common.SourceEnum, System.String) 000000001b8ad6d8 000007fef8816869 [HelperMethodFrame: 000000001b8ad6d8] 000000001b8ad820 000007feec2b6c6f System.DirectoryServices.PropertyValueCollection.PopulateList() 000000001b8ad860 000007feec225f0f System.DirectoryServices.PropertyValueCollection..ctor(System.DirectoryServices.DirectoryEntry, System.String) 000000001b8ad8a0 000007feec22d023 System.DirectoryServices.PropertyCollection.get_Item(System.String) 000000001b8ad8f0 000007ff00274d34 Common.DirectoryEntryExtension.GetStringAttribute(System.String) 000000001b8ad940 000007ff0027f507 DirectoryServiceLib.LdapProvider.DirectoryPost.Copy(DirectoryServiceLib.LdapProvider.DirectoryPost) 000000001b8ad980 000007ff0027a7cf DirectoryServiceLib.LdapProvider.Directory.CreatePost(System.String, DirectoryServiceLib.Model.Post, DirectoryServiceLib.Model.Presumptions, Services.Common.SourceEnum, System.String) 000000001b8adbe0 000007ff00279532 DirectoryServiceLib.WCFDirectory.CreatePost(System.String, DirectoryServiceLib.Model.Post, DirectoryServiceLib.Model.Presumptions, Services.Common.SourceEnum, System.String) 000000001b8adc60 000007ff001f47bd DynamicClass.SyncInvokeCreatePost(System.Object, System.Object[], System.Object[]) My conclusion is that it fails when the code is calling System.DirectoryServices.PropertyCollection.get_Item(System.String). So after issuing an !CLRStack -a I get this result: 000000001b8ad8a0 000007feec22d023 System.DirectoryServices.PropertyCollection.get_Item(System.String) PARAMETERS: this = <no data> propertyName = <no data> LOCALS: <CLR reg> = 0x0000000001dcef78 <no data> My very first question is why does it display no data on the propertyname? I am kinda new on Windbg. However I executed an dumpobject on = 0x0000000001dcef78: 0:013> !do 0x0000000001dcef78 Name: System.String MethodTable: 000007fef66d6960 EEClass: 000007fef625eec8 Size: 74(0x4a) bytes File: C:\Windows\Microsoft.Net\assembly\GAC_64\mscorlib\v4.0_4.0.0.0__b77a5c561934e089\mscorlib.dll String: personalprescriptioncode Fields: MT Field Offset Type VT Attr Value Name 000007fef66dc848 40000ed 8 System.Int32 1 instance 24 m_stringLength 000007fef66db388 40000ee c System.Char 1 instance 70 m_firstChar 000007fef66d6960 40000ef 10 System.String 0 shared static Empty >> Domain:Value 0000000000174e10:00000000019d1420 000000001a886f50:00000000019d1420 << So when the source code wants to fetch the personalprescriptioncode from Active Directory(what is used for persistence layer) it fails. Looking back at the stack it is when issuing the Copy method. DirectoryServiceLib.LdapProvider.DirectoryPost.Copy(DirectoryServiceLib.LdapProvider.DirectoryPost) So looking in the sourcecode: DirectoryPost postInLimbo = DirectoryPostFactory.Instance().GetDirectoryPost(LdapConfigReader.Instance().GetConfigValue("LimboDN"), idGenPerson.ID.UserId); if (postInLimbo != null) newPost.Copy(postInLimbo); This code is looking for another post in OU=limbo with the same UserId and if it finds one it copies the attributes to the new post. In this case it does and it fails with personalprescriptioncode. I've looked in Active Directory under OU=Limbo and the post exist there with the attribute personalprescriptioncode=31243. Question 1: Why does it display no data for some of the PARAMETERS and LOCALS? Is it the GC who has cleaned up before the memorydump had been created. Question 2: Is there anymore i can do to get to the solution to this problem?

  Read the article

• Thread Synchronisation 101

  - by taspeotis

  Previously I've written some very simple multithreaded code, and I've always been aware that at any time there could be a context switch right in the middle of what I'm doing, so I've always guarded access the shared variables through a CCriticalSection class that enters the critical section on construction and leaves it on destruction. I know this is fairly aggressive and I enter and leave critical sections quite frequently and sometimes egregiously (e.g. at the start of a function when I could put the CCriticalSection inside a tighter code block) but my code doesn't crash and it runs fast enough. At work my multithreaded code needs to be a tighter, only locking/synchronising at the lowest level needed. At work I was trying to debug some multithreaded code, and I came across this: EnterCriticalSection(&m_Crit4); m_bSomeVariable = true; LeaveCriticalSection(&m_Crit4); Now, m_bSomeVariable is a Win32 BOOL (not volatile), which as far as I know is defined to be an int, and on x86 reading and writing these values is a single instruction, and since context switches occur on an instruction boundary then there's no need for synchronising this operation with a critical section. I did some more research online to see whether this operation did not need synchronisation, and I came up with two scenarios it did: The CPU implements out of order execution or the second thread is running on a different core and the updated value is not written into RAM for the other core to see; and The int is not 4-byte aligned. I believe number 1 can be solved using the "volatile" keyword. In VS2005 and later the C++ compiler surrounds access to this variable using memory barriers, ensuring that the variable is always completely written/read to the main system memory before using it. Number 2 I cannot verify, I don't know why the byte alignment would make a difference. I don't know the x86 instruction set, but does mov need to be given a 4-byte aligned address? If not do you need to use a combination of instructions? That would introduce the problem. So... QUESTION 1: Does using the "volatile" keyword (implicity using memory barriers and hinting to the compiler not to optimise this code) absolve a programmer from the need to synchronise a 4-byte/8-byte on x86/x64 variable between read/write operations? QUESTION 2: Is there the explicit requirement that the variable be 4-byte/8-byte aligned? I did some more digging into our code and the variables defined in the class: class CExample { private: CRITICAL_SECTION m_Crit1; // Protects variable a CRITICAL_SECTION m_Crit2; // Protects variable b CRITICAL_SECTION m_Crit3; // Protects variable c CRITICAL_SECTION m_Crit4; // Protects variable d // ... }; Now, to me this seems excessive. I thought critical sections synchronised threads between a process, so if you've got one you can enter it and no other thread in that process can execute. There is no need for a critical section for each variable you want to protect, if you're in a critical section then nothing else can interrupt you. I think the only thing that can change the variables from outside a critical section is if the process shares a memory page with another process (can you do that?) and the other process starts to change the values. Mutexes would also help here, named mutexes are shared across processes, or only processes of the same name? QUESTION 3: Is my analysis of critical sections correct, and should this code be rewritten to use mutexes? I have had a look at other synchronisation objects (semaphores and spinlocks), are they better suited here? QUESTION 4: Where are critical sections/mutexes/semaphores/spinlocks best suited? That is, which synchronisation problem should they be applied to. Is there a vast performance penalty for choosing one over the other? And while we're on it, I read that spinlocks should not be used in a single-core multithreaded environment, only a multi-core multithreaded environment. So, QUESTION 5: Is this wrong, or if not, why is it right? Thanks in advance for any responses :)

  Read the article

• Survey Data Model - How to avoid EAV and excessive denormalization?

  - by AlexDPC

  Hi everyone, My database skills are mediocre at best and I have to design a data model for survey data. I have spent some thoughts on this and right now I feel that I am stuck between some kind of EAV model and a design involving hundreds of tables, each with hundreds of columns (and thousands of records). There must be a better way to do this and I hope that the wise folks on this forum can help me. I have already searched various forums, but I couldn't really find a solution. If it has already been given elsewhere, please excuse me and provide me with a link so I can read it up. Some assumptions about the data I have to deal with: Each survey consists of 1 to n questionnaires Each questionnaire consists of 100-2,000 questions (please ignore that 2,000 questions really sound like a lot to answer...) Questions can be of various types: multiple-choice, free text, a number (like age, income, percentages, ...) Each survey involves 10-200 countries (These are not the respondents. The respondents are actually people in the countries.) Depending on the type of questionnaire, each questionnaire is answered by 100-20,000 respondents per country. A country can adapt the questionnaires for a survey, i.e. add, remove or edit questions The data for one country is gathered in a separate database in that country. There is no possibility for online integration from the start. The data for all countries has to be integrated later. This means for example, if a country has deleted a question, that data must somehow be derived from what they sent in order to achieve a uniform design across all countries I will have to write the integration and cleaning software, which will need to work with every country's data In the end the data needs to be exported to flat files, one rectangular grid per country and questionnaire. I have already discussed this topic with people from various backgrounds and have not come to a good solution yet. I mainly got two kinds of opinions. The domain experts, who are used to working with flat files (spreadsheet-style) for data processing and analysis vote for a denormalized structure with loads of tables and columns as I described above (1 table per country and questionnaire). This sounds terrible to me, because I learned that wide tables are to be avoided, it will be annoying to determine which columns are actually in a table when working with it, the database will become cluttered with hundreds of tables (or I even need to set up multiple databases, each with a similar yet a bit differetn design), etc. O-O-programmers vote for a strongly "normalized" design, which would effectively lead to a central table containing all the answers from all respondents to all questions. This table would either need to contain a column of type sql_variant type or multiple answer columns with different types to store answers of different types (multiple choice, free text, ..). The former would essentially be a EAV model. I tend to follow Joe Celko here, who strongly discourages its use (he calls it OTLT or "One True Lookup Table"). The latter would imply that each row would contain null cells for the not applicable types by design. Another alternative I could think of would be to create one table per answer type, i.e., one for multiple-choice questions, one for free text questions, etc.. That's not so generic, it would lead to a lot of union joins, I think and I would have to add a table if a new answer type is invented. Sorry for boring you with all this text and thank you for your input! Cheers, Alex PS: I asked the same question here: http://www.eggheadcafe.com/community/aspnet/13/10242616/survey-data-model--how-to-avoid-eav-and-excessive-denormalization.aspx

  Read the article

• Application shows low memory warning and crashes while loading images?

  - by Bhoomi

  I am using following code for loading images from server using following code.When i scroll UITableView application crashes. AsynchrohousImageView class .m file - (void)dealloc { [connection cancel]; //in case the URL is still downloading [connection release]; [data release]; [_imageView release]; [_activityIndicator release]; [super dealloc]; } - (void)loadImageFromURL:(NSURL*)url defaultImageName:(NSString *)defaultImageName showDefaultImage:(BOOL)defaultImageIsShown showActivityIndicator:(BOOL)activityIndicatorIsShown activityIndicatorRect:(CGRect)activityIndicatorRect activityIndicatorStyle:(UIActivityIndicatorViewStyle)activityIndicatorStyle { if (connection!=nil) { [connection release]; } if (data!=nil) { [data release]; } if ([[self subviews] count]>0) { [[[self subviews] objectAtIndex:0] removeFromSuperview]; // } if (defaultImageIsShown) { self.imageView = [[[UIImageView alloc] initWithImage:[UIImage imageNamed:defaultImageName]] autorelease]; } else { self.imageView = [[[UIImageView alloc] init] autorelease]; } [self addSubview:_imageView]; _imageView.frame = self.bounds; [_imageView setNeedsLayout]; [self setNeedsLayout]; if (activityIndicatorIsShown) { self.activityIndicator = [[[UIActivityIndicatorView alloc] initWithActivityIndicatorStyle:activityIndicatorStyle] autorelease]; [self addSubview:_activityIndicator]; _activityIndicator.frame = activityIndicatorRect; _activityIndicator.center = CGPointMake(_imageView.frame.size.width/2, _imageView.frame.size.height/2); [_activityIndicator setHidesWhenStopped:YES]; [_activityIndicator startAnimating]; } NSURLRequest* request = [NSURLRequest requestWithURL:url cachePolicy:NSURLRequestUseProtocolCachePolicy timeoutInterval:60.0]; connection = [[NSURLConnection alloc] initWithRequest:request delegate:self]; } - (void)connection:(NSURLConnection *)theConnection didReceiveData:(NSData *)incrementalData { if (data==nil) { data = [[NSMutableData alloc] initWithCapacity:2048]; } [data appendData:incrementalData]; } - (void)connectionDidFinishLoading:(NSURLConnection*)theConnection { [connection release]; connection=nil; _imageView.image = [UIImage imageWithData:data]; if (_activityIndicator) { [_activityIndicator stopAnimating]; } [data release]; data=nil; } - (UIImage*) image { UIImageView* iv = [[self subviews] objectAtIndex:0]; return [iv image]; } In ViewController Class Which loads image - (UITableViewCell *)tableView:(UITableView *)tV cellForRowAtIndexPath:(NSIndexPath *)indexPath { static NSString *reuseIdentifier =@"CellIdentifier"; ListCell *cell = (ListCell *)[tableView dequeueReusableCellWithIdentifier:reuseIdentifier]; if (cell==nil) { cell = [[ListCell alloc]initWithStyle:UITableViewCellStyleDefault reuseIdentifier:reuseIdentifier]; NSMutableDictionary *dicResult = [arrResults objectAtIndex:indexPath.row]; NSURL *url=[NSURL URLWithString:[dicResult objectForKey:@"Image"]]; AsynchronousImageView *asyncImageView = [[AsynchronousImageView alloc] initWithFrame:CGRectMake(5, 10,80,80)]; [asyncImageView loadImageFromURL:url defaultImageName:@"DefaultImage.png" showDefaultImage:NO showActivityIndicator:YES activityIndicatorRect:CGRectMake(5, 10,30,30) activityIndicatorStyle:UIActivityIndicatorViewStyleGray]; // load our image with URL asynchronously [cell.contentView addSubview:asyncImageView]; // cell.imgLocationView.image = [UIImage imageNamed:[dicResult valueForKey:@"Image"]]; [asyncImageView release]; } if([arrResults count]==1) { UITableViewCell *cell1=[tableView dequeueReusableCellWithIdentifier:reuseIdentifier]; if(cell1==nil) cell1=[[[UITableViewCell alloc]initWithStyle:UITableViewCellStyleDefault reuseIdentifier:reuseIdentifier] autorelease]; NSMutableDictionary *dicResult = [arrResults objectAtIndex:0]; cell1.textLabel.text=[dicResult valueForKey:@"NoResults"]; return cell1; } else { NSMutableDictionary *dicResult = [arrResults objectAtIndex:indexPath.row]; NSString *title = [NSString stringWithFormat:@"%@ Bedrooms-%@", [dicResult valueForKey:KEY_NUMBER_OF_BEDROOMS],[dicResult valueForKey:KEY_PROPERTY_TYPE]]; NSString *strAddress = [dicResult valueForKey:KEY_DISPLAY_NAME]; NSString *address = [strAddress stringByReplacingOccurrencesOfString:@", " withString:@"\n"]; NSString *price = [dicResult valueForKey:KEY_PRICE]; NSString *distance = [dicResult valueForKey:KEY_DISTANCE]; cell.accessoryType = UITableViewCellAccessoryDisclosureIndicator; cell.lblTitle.text = title; cell.lblAddress.text = address; if ([price length]>0) { cell.lblPrice.text = [NSString stringWithFormat:@"£%@",price]; }else{ cell.lblPrice.text = @""; } if ([distance length]>0) { cell.lblmiles.text = [NSString stringWithFormat:@"%.2f miles",[distance floatValue]]; }else{ cell.lblmiles.text = @""; } } return cell; } How can i resolve this? I have attached heapshot analysis screen shot of it.Here non Object consumes so much of memory what is that?

  Read the article

• "assignment makes integer from pointer without a cast " warning in c

  - by mekasperasky

  #include<stdio.h> /* this is a lexer which recognizes constants , variables ,symbols, identifiers , functions , comments and also header files . It stores the lexemes in 3 different files . One file contains all the headers and the comments . Another file will contain all the variables , another will contain all the symbols. */ int main() { int i=0,j; char a,b[20],c[30]; FILE *fp1,*fp2; c[0]='"if"; c[1]="then"; c[2]="else"; c[3]="switch"; c[4]="printf"; c[5]="scanf"; c[6]="NULL"; c[7]="int"; c[8]="char"; c[9]="float"; c[10]="long"; c[11]="double"; c[12]="char"; c[13]="const"; c[14]="continue"; c[15]="break"; c[16]="for"; c[17]="size of"; c[18]="register"; c[19]="short"; c[20]="auto"; c[21]="while"; c[22]="do"; c[23]="case"; fp1=fopen("source.txt","r"); //the source file is opened in read only mode which will passed through the lexer fp2=fopen("lext.txt","w"); //now lets remove all the white spaces and store the rest of the words in a file if(fp1==NULL) { perror("failed to open source.txt"); //return EXIT_FAILURE; } i=0; while(!feof(fp1)) { a=fgetc(fp1); if(a!=' ') { b[i]=a; } else { for (j=0;j<23;j++) { if(c[j]==b) { fprintf(fp2, "%.20s\n", c[j]); continue ; } b[i]='\0'; fprintf(fp2, "%.20s\n", b); i=0; continue; } //else if //{ i=i+1; /*Switch(a) { case EOF :return eof; case '+':sym=sym+1; case '-':sym=sym+1; case '*':sym=sym+1; case '/':sym=sym+1; case '%':sym=sym+1; case ' */ } fclose(fp1); fclose(fp2); return 0; } This is my c code for lexical analysis .. its giving warnings and also not writing anything into the lext file ..

  Read the article

• ERROR: Linux route add command failed: external program exited with error status: 4

  - by JohnMerlino

  A remote machine running fedora uses openvpn, and multiple developers were successfully able to connect to it via their client openvpn. However, I am running Ubuntu 12.04 and I am having trouble connecting to the server via vpn. I copied ca.crt, home.key, and home.crt from the server to my local machine to /etc/openvpn folder. My client.conf file looks like this: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote xx.xxx.xx.130 1194 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nogroup # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca ca.crt cert home.crt key home.key # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 But when I start server and look in /var/log/syslog, I notice the following error: May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 10.27.12.1 netmask 255.255.255.252 gw 10.27.12.37 May 27 22:13:51 myuser ovpn-client[5626]: ERROR: Linux route add command failed: external program exited with error status: 4 May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 172.27.12.0 netmask 255.255.255.0 gw 10.27.12.37 May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 10.27.12.1 netmask 255.255.255.255 gw 10.27.12.37 And I am unable to connect to the server via openvpn: $ ssh [email protected] ssh: connect to host xxx.xx.xx.130 port 22: No route to host What may I be doing wrong?

  Read the article

• How To Switch Back to Outlook 2007 After the 2010 Beta Ends

  - by Matthew Guay

  Are you switching back to Outlook 2007 after trying out Office 2010 beta?  Here’s how you can restore your Outlook data and keep everything working fine after the switch. Whenever you install a newer version of Outlook, it will convert your profile and data files to the latest format.  This makes them work the best in the newer version of Outlook, but may cause problems if you decide to revert to an older version.  If you installed Outlook 2010 beta, it automatically imported and converted your profile from Outlook 2007.  When the beta expires, you will either have to reinstall Office 2007 or purchase a copy of Office 2010. If you choose to reinstall Office 2007, you may notice an error message each time you open Outlook. Outlook will still work fine and all of your data will be saved, but this error message can get annoying.  Here’s how you can create a new profile, import all of your old data, and get rid of this error message. Banish the Error Message with a New Profile To get rid of this error message, we need to create a new Outlook profile.  First, make sure your Outlook data files are backed up.  Your messages, contacts, calendar, and more are stored in a .pst file in your appdata folder.  Enter the following in the address bar of an Explorer window to open your Outlook data folder, and replace username with your user name: C:\Users\username\AppData\Local\Microsoft\Outlook Copy the Outlook Personal Folders (.pst) files that contain your data. Its name is usually your email address, though it may have a different name.  If in doubt, select all of the Outlook Personal Folders files, copy them, and save them in another safe place (such as your Documents folder). Now, let’s remove your old profile.  Open Control Panel, and select Mail.  In Windows Vista or 7, simply enter “Mail” in the search box and select the first entry. Click the “Show Profiles…” button. Now, select your Outlook profile, and click Remove.  This will not delete your data files, but will remove them from Outlook. Press Yes to confirm that you wish to remove this profile. Open Outlook, and you will be asked to create a new profile.  Enter a name for your new profile, and press Ok. Now enter your email account information to setup Outlook as normal. Outlook will attempt to automatically configure your account settings.  This usually works for accounts with popular email systems, but if it fails to find your information you can enter it manually.  Press finish when everything’s done. Outlook will now go ahead and download messages from your email account.  In our test, we used a Gmail account that still had all of our old messages online.  Those files are backed up in our old Outlook data files, so we can save time and not download them.  Click the Send/Receive button on the bottom of the window, and select “Cancel Send/Receive”. Restore Your Old Outlook Data Let’s add our old Outlook file back to Outlook 2007.  Exit Outlook, and then go back to Control Panel, and select Mail as above.  This time, click the Data Files button. Click the Add button on the top left. Select “Office Outlook Personal Folders File (.pst)”, and click Ok. Now, select your old Outlook data file.  It should be in the folder that opens by default; if not, browse to the backup copy we saved earlier, and select it. Press Ok at the next dialog to accept the default settings. Now, select the data file we just imported, and click “Set as Default”. Now, all of your old messages, appointments, contacts, and everything else will be right in Outlook ready for you.  Click Ok, and then open Outlook to see the change. All of the data that was in Outlook 2010 is now ready to use in Outlook 2007.  You won’t have to wait to re-download all of your emails from the server since everything’s still here ready to be used.  And when you open Outlook, you won’t see any error messages, either! Conclusion Migrating your Outlook profile back to Outlook 2007 is fairly easy, and with these steps, you can avoid seeing an error message every time you open Outlook.  With all your data in tact, you’re ready to get back to work instead of getting frustrated with Outlook.  Many of us use webmail and keep all of our messages in the cloud, but even on broadband connections it can take a long time to download several gigabytes of emails. Similar Articles Productive Geek Tips Opening Attachments in Outlook 2007 by KeyboardQuickly Create Appointments from Tasks with Outlook 2007’s To-Do BarFix For Outlook 2007 Constantly Asking for Password on VistaPin Microsoft Outlook to the Desktop BackgroundOur Look at the LinkedIn Social Connector for Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook

  Read the article

• Upgrading from TFS 2010 RC to TFS 2010 RTM done

  - by Martin Hinshelwood

  Today is the big day, with the Launch of Visual Studio 2010 already done in Asia, and rolling around the world towards us, we are getting ready for the RTM (Released). We have had TFS 2010 in Production for nearly 6 months and have had only minimal problems. Update 12th April 2010  – Added Scott Hanselman’s tweet about the MSDN download release time. SSW was the first company in the world outside of Microsoft to deploy Visual Studio 2010 Team Foundation Server to production, not once, but twice. I am hoping to make it 3 in a row, but with all the hype around the new version, and with it being a production release and not just a go-live, I think there will be a lot of competition. Developers: MSDN will be updated with #vs2010 downloads and details at 10am PST *today*! @shanselman - Scott Hanselman Same as before, we need to Uninstall 2010 RC and install 2010 RTM. The installer will take care of all the complexity of actually upgrading any schema changes. If you are upgrading from TFS 2008 to TFS2010 you can follow our Rules To Better TFS 2010 Migration and read my post on our successes.   We run TFS 2010 in a Hyper-V virtual environment, so we have the advantage of running a snapshot as well as taking a DB backup. Done - Snapshot the hyper-v server Microsoft does not support taking a snapshot of a running server, for very good reason, and Brian Harry wrote a post after my last upgrade with the reason why you should never snapshot a running server. Done - Uninstall Visual Studio Team Explorer 2010 RC You will need to uninstall all of the Visual Studio 2010 RC client bits that you have on the server. Done - Uninstall TFS 2010 RC Done - Install TFS 2010 RTM Done - Configure TFS 2010 RTM Pick the Upgrade option and point it at your existing “tfs_Configuration” database to load all of the existing settings Done - Upgrade the SharePoint Extensions Upgrade Build Servers (Pending) Test the server The back out plan, and you should always have one, is to restore the snapshot. Upgrading to Team Foundation Server 2010 – Done The first thing you need to do is off the TFS server and then log into the Hyper-v server and create a snapshot. Figure: Make sure you turn the server off and delete all old snapshots before you take a new one I noticed that the snapshot that was taken before the Beta 2 to RC upgrade was still there. You should really delete old snapshots before you create a new one, but in this case the SysAdmin (who is currently tucked up in bed) asked me not to. I guess he is worried about a developer messing up his server Turn your server on and wait for it to boot in anticipation of all the nice shiny RTM’ness that is coming next. The upgrade procedure for TFS2010 is to uninstal the old version and install the new one. Figure: Remove Visual Studio 2010 Team Foundation Server RC from the system.   Figure: Most of the heavy lifting is done by the Uninstaller, but make sure you have removed any of the client bits first. Specifically Visual Studio 2010 or Team Explorer 2010.  Once the uninstall is complete, this took around 5 minutes for me, you can begin the install of the RTM. Running the 64 bit OS will allow the application to use more than 2GB RAM, which while not common may be of use in heavy load situations. Figure: It is always recommended to install the 64bit version of a server application where possible. I do not think it is likely, with SharePoint 2010 and Exchange 2010  and even Windows Server 2008 R2 being 64 bit only, I do not think there will be another release of a server app that is 32bit. You then need to choose what it is you want to install. This depends on how you are running TFS and on how many servers. In our case we run TFS and the Team Foundation Build Service (controller only) on out TFS server along with Analysis services and Reporting Services. But our SharePoint server lives elsewhere. Figure: This always confuses people, but in reality it makes sense. Don’t install what you do not need. Every extra you install has an impact of performance. If you are integrating with SharePoint you will need to run this install on every Front end server in your farm and don’t forget to upgrade your Build servers and proxy servers later. Figure: Selecting only Team Foundation Server (TFS) and Team Foundation Build Services (TFBS)   It is worth noting that if you have a lot of builds kicking off, and hence a lot of get operations against your TFS server, you can use a proxy server to cache the source control on another server in between your TFS server and your build servers. Figure: Installing Microsoft .NET Framework 4 takes the most time. Figure: Now run Windows Update, and SSW Diagnostic to make sure all your bits and bobs are up to date. Note: SSW Diagnostic will check your Power Tools, Add-on’s, Check in Policies and other bits as well. Configure Team Foundation Server 2010 – Done Now you can configure the server. If you have no key you will need to pick “Install a Trial Licence”, but it is only £500, or free with a MSDN subscription. Anyway, if you pick Trial you get 90 days to get your key. Figure: You can pick trial and add your key later using the TFS Server Admin. Here is where the real choices happen. We are doing an Upgrade from a previous version, so I will pick Upgrade the same as all you folks that are using the RC or TFS 2008. Figure: The upgrade wizard takes your existing 2010 or 2008 databases and upgraded them to the release.   Once you have entered your database server name you can click “List available databases” and it will show what it can upgrade. Figure: Select your database from the list and at this point, make sure you have a valid backup. At this point you have not made ANY changes to the databases. At this point the configuration wizard will load configuration from your existing database if you have one. If you are upgrading TFS 2008 refer to Rules To Better TFS 2010 Migration. Mostly during the wizard the default values will suffice, but depending on the configuration you want you can pick different options. Figure: Set the application tier account and Authentication method to use. We use NTLM to keep things simple as we host our TFS server externally for our remote developers.  Figure: Setting your TFS server URL’s to be the remote URL’s allows the reports to be accessed without using VPN. Very handy for those remote developers. Figure: Detected the existing Warehouse no problem. Figure: Again we love green ticks. It gives us a warm fuzzy feeling. Figure: The username for connecting to Reporting services should be a domain account (if you are on a domain that is). Figure: Setup the SharePoint integration to connect to your external SharePoint server. You can take the option to connect later.   You then need to run all of your readiness checks. These check can save your life! it will check all of the settings that you have entered as well as checking all the external services are configures and running properly. There are two reasons that TFS 2010 is so easy and painless to install where previous version were not. Microsoft changes the install to two steps, Install and configuration. The second reason is that they have pulled out all of the stops in making the install run all the checks necessary to make sure that once you start the install that it will complete. if you find any errors I recommend that you report them on http://connect.microsoft.com so everyone can benefit from your misery.   Figure: Now we have everything setup the configuration wizard can do its work.  Figure: Took a while on the “Web site” stage for some point, but zipped though after that.  Figure: last wee bit. TFS Needs to do a little tinkering with the data to complete the upgrade. Figure: All upgraded. I am not worried about the yellow triangle as SharePoint was being a little silly Exception Message: TF254021: The account name or password that you specified is not valid. (type TfsAdminException) Exception Stack Trace:    at Microsoft.TeamFoundation.Management.Controls.WizardCommon.AccountSelectionControl.TestLogon(String connectionString)    at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument) [Info   @16:10:16.307] Benign exception caught as part of verify: Exception Message: TF255329: The following site could not be accessed: http://projects.ssw.com.au/. The server that you specified did not return the expected response. Either you have not installed the Team Foundation Server Extensions for SharePoint Products on this server, or a firewall is blocking access to the specified site or the SharePoint Central Administration site. For more information, see the Microsoft Web site (http://go.microsoft.com/fwlink/?LinkId=161206). (type TeamFoundationServerException) Exception Stack Trace:    at Microsoft.TeamFoundation.Client.SharePoint.WssUtilities.VerifyTeamFoundationSharePointExtensions(ICredentials credentials, Uri url)    at Microsoft.TeamFoundation.Admin.VerifySharePointSitesUrl.Verify() Inner Exception Details: Exception Message: TF249064: The following Web service returned an response that is not valid: http://projects.ssw.com.au/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. Either the extensions are not installed, the request resulted in HTML being returned, or there is a problem with the URL. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://projects.ssw.com.au. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. (type TeamFoundationServerInvalidResponseException) Exception Data Dictionary: ResponseStatusCode = InternalServerError I’ll look at SharePoint after, probably the SharePoint box just needs a restart or a kick If there is a problem with SharePoint it will come out in testing, But I will definatly be passing this on to Microsoft.   Upgrading the SharePoint connector to TFS 2010 You will need to upgrade the Extensions for SharePoint Products and Technologies on all of your SharePoint farm front end servers. To do this uninstall  the TFS 2010 RC from it in the same way as the server, and then install just the RTM Extensions. Figure: Only install the SharePoint Extensions on your SharePoint front end servers. TFS 2010 supports both SharePoint 2007 and SharePoint 2010.   Figure: When you configure SharePoint it uploads all of the solutions and templates. Figure: Everything is uploaded Successfully. Figure: TFS even remembered the settings from the previous installation, fantastic.   Upgrading the Team Foundation Build Servers to TFS 2010 Just like on the SharePoint servers you will need to upgrade the Build Server to the RTM. Just uninstall TFS 2010 RC and then install only the Team Foundation Build Services component. Unlike on the SharePoint server you will probably have some version of Visual Studio installed. You will need to remove this as well. (Coming Soon) Connecting Visual Studio 2010 / 2008 / 2005 and Eclipse to TFS2010 If you have developers still on Visual Studio 2005 or 2008 you will need do download the respective compatibility pack: Visual Studio Team System 2005 Service Pack 1 Forward Compatibility Update for Team Foundation Server 2010 Visual Studio Team System 2008 Service Pack 1 Forward Compatibility Update for Team Foundation Server 2010 If you are using Eclipse you can download the new Team Explorer Everywhere install for connecting to TFS. Get your developers to check that you have the latest version of your applications with SSW Diagnostic which will check for Service Packs and hot fixes to Visual Studio as well.   Technorati Tags: TFS,TFS2010,TFS 2010,Upgrade

  Read the article

• Our Look at the Internet Explorer 9 Platform Preview

  - by Asian Angel

  Have you been hearing all about Microsoft’s work on Internet Explorer 9 and are curious about it? If you are wanting a taste of the upcoming release then join us as we take a look at the Internet Explorer 9 Platform Preview. Note: Windows Vista and Server 2008 users may need to install a Platform Update (see link at bottom for more information). Getting Started If you are curious about the systems that the platform preview will operate on here is an excerpt from the FAQ page (link provided below). There are two important points of interest here: The platform preview does not replace your regular Internet Explorer installation The platform preview (and the final version of Internet Explorer 9) will not work on Windows XP There really is not a lot to the install process…basically all that you will have to deal with is the “EULA Window” and the “Install Finished Window”. Note: The platform preview will install to a “Program Files Folder” named “Internet Explorer Platform Preview”. Internet Explorer 9 Platform Preview in Action When you start the platform preview up for the first time you will be presented with the Internet Explorer 9 Test Drive homepage. Do not be surprised that there is not a lot to the UI at this time…but you can get a good idea of how Internet Explorer will act. Note: You will not be able to alter the “Homepage” for the platform preview. Of the four menus available there are two that will be of interest to most people…the “Page & Debug Menus”. If you go to navigate to a new webpage you will need to go through the “Page Menu” unless you have installed the Address Bar Mini-Tool (shown below). Want to see what a webpage will look like in an older version of Internet Explorer? Then choose your version in the “Debug Menu”. We did find it humorous that IE6 was excluded from the choices offered. Here is what the URL entry window looks like if you are using the “Page Menu” to navigate between websites. Here is the main page of the site here displayed in “IE9 Mode”…looking good. Here is the main page viewed in “Forced IE5 Document Mode”. There were some minor differences (colors, sidebar, etc.) in how the main page displayed in comparison to “IE9 Mode”. Being able to switch between modes makes for an interesting experience… As you can see there is not much to the “Context Menu” at the moment. Notice the slightly altered icon for the platform preview… “Add” an Address Bar of Sorts If you would like to use a “make-shift” Address Bar with the platform preview you can set up the portable file (IE9browser.exe) for the Internet Explorer 9 Test Platform Addressbar Mini-Tool. Just place it in an appropriate folder, create a shortcut for it, and it will be ready to go. Here is a close look at the left side of the Address Bar Mini-Tool. You can try to access “IE Favorites” but may have sporadic results like those we experienced during our tests. Note: The Address Bar Mini-Tool will not line up perfectly with the platform preview but still makes a nice addition. And a close look at the right side of the Address Bar Mini-Tool. In order to completely shut down the Address Bar Mini-Tool you will need to click on “Close”. Each time that you enter an address into the Address Bar Mini-Tool it will open a new window/instance of the platform preview. Note: During our tests we noticed that clicking on “Home” in the “Page Menu” opened the previously viewed website but once we closed and restarted the platform preview the test drive website was the starting/home page again. Even if the platform preview is not running the Address Bar Mini-Tool can still run as shown here. Note: You will not be able to move the Address Bar Mini-Tool from its’ locked-in position at the top of the screen. Now for some fun. With just the Address Bar Mini-Tool open you can enter an address and cause the platform preview to open. Here is our example from above now open in the platform preview…good to go. Conclusion During our tests we did experience the occasional crash but overall we were pleased with the platform preview’s performance. The platform preview handled rather well and definitely seemed much quicker than Internet Explorer 8 on our test system (a definite bonus!). If you are an early adopter then this could certainly get you in the mood for the upcoming beta releases! Links Download the Internet Explorer 9 Preview Platform Download the Internet Explorer 9 Test Platform Addressbar Mini-Tool Information about Platform Update for Windows Vista & Server 2008 View the Internet Explorer 9 Platform Preview FAQ Similar Articles Productive Geek Tips Mysticgeek Blog: A Look at Internet Explorer 8 Beta 1 on Windows XPMake Ctrl+Tab in Internet Explorer 7 Use Most Recent OrderRemove ISP Text or Corporate Branding from Internet Explorer Title BarWhy Can’t I Turn the Details/Preview Panes On or Off in Windows Vista Explorer?Prevent Firefox or Internet Explorer from Printing the URL on Every Page TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awesome Lyrics Finder for Winamp & Windows Media Player Download Videos from Hulu Pixels invade Manhattan Convert PDF files to ePub to read on your iPad Hide Your Confidential Files Inside Images Get Wildlife Photography Tips at BBC’s PhotoMasterClasses

  Read the article

• Geek Fun: Virtualized Old School Windows – Windows 95

  - by Matthew Guay

  Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

  Read the article

• Geek Fun: Virtualized Old School Windows – Windows 95

  - by Matthew Guay

  Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

  Read the article

• SQL SERVER – Signal Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

  - by pinaldave

  In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Signal Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Signal Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Signal Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the Signalwait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the Signal wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the Signal wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

• Secure wipe of a hard drive using WinPE.

  - by Derek Meier

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} The wiping of a hard drive is typically seen as fairly trivial.  There are tons of applications out there that will do it for you.  Point àClickàGlobal-Thermo Nuclear War. However, these applications are typically expensive or unreliable.  Plus, if you have a laptop or lack a secondary computer to put the hard drive into – how on earth do you wipe it quickly and easily while still conforming to a 7 pass rule (this means that every possible bit on the hard drive is set to 0 and then to 1 seven times in a row)?  Yes, one pass should be enough – as turning every bit from a 1 to a zero will wipe the data from existence.  But, we’re dealing with tinfoil hat wearing types here people.  DOD standards dictate at least 3 passes, and typically 7 is the preferred amount.  I’m not going to argue about data recovery.  I have been told to use 7 passes, and so I will.  So say we all! Quite some time ago I used to make a BartPE XP-based boot cd for the original purpose of securely wiping data.  I loved BartPE and integrated so many plugins into my builds that I could do pretty much anything directly from CD.  Reset passwords, uninstall security updates, wipe drives, chkdsk, remove spyware, install Windows, etc.  However, with the newer multi-core systems and new chipsets coming out from vendors, I found that BartPE was rather difficult to keep up to date.  I have since switched to WinPE 3.0 (Windows Preinstallation Environment). http://technet.microsoft.com/en-us/library/cc748933(WS.10).aspx  It is fairly simple to create your own CD, and I have made a few helpful scripts to easily integrate drivers and rebuild the ISO file for you.  I’ll cover making your own boot CD utilizing WinPE 3.0 in a later post – I can talk about WinPE forever and need to collect my thoughts!!  My wife loves talking about WinPE almost as much as talking about Doctor Who.  Wait, did I say loves?  Hmmmm, I may have meant loathes. The topic at hand?  Right. Wiping a drive! I must have drunk too much coffee this morning.  I like to use a simple batch script that calls a combination of diskpart.exe from Microsoft® and Sdelete.exe created by our friend Mark Russinovich. http://technet.microsoft.com/en-us/sysinternals/bb897443.aspx All of the following files are located within the same directory on my WinPE boot CD. Here are the contents of wipe_me.bat, script.txt and sdelete.reg. Wipe_me.bat:   @echo off echo. echo     I will completely wipe the local hard drives using echo     7 individual wipes. The data will NOT echo     be recoverable.  I will begin after you pause echo. echo Preparing to partition and format disk. Diskpart.exe /s "script.txt" REM I was annoyed by not having a completely automated script – and Sdelete wants you to accept the license agreement. So, I added a registry file to skip doing that. regedit /S sdelete.reg rem sdelete options selected are: -p (passes) -c (zero free space) -s (recurse through subdirectories, if any) -z (clean free space) [drive letter] sdelete.exe -p 7 -c -s -z c: echo. echo Pass seven complete. echo. echo Wiping complete. Pause exit script.txt: list disk select disk 0 clean create partition primary select partition 1 active format FS=NTFS LABEL="New Volume" QUICK assign letter=c exit *Notes: This script assumes one local hard drive – change the script as you see fit for your environment.  The clean command will overwrite the master boot record and any hidden sector information – so be careful!   sdelete.reg: Windows Registry Editor Version 5.00 [HKEY_CURRENT_USER\Software\Sysinternals\SDelete] "EulaAccepted"=dword:00000001   With a combination of WinPE, sdelete.exe and your friendly neighborhood text editor you can begin wiping drives as quickly and easily as possible!  I hope this helps, I get asked this a lot in my line of work. Best of luck, Derek

  Read the article

• SQL SERVER – Enumerations in Relational Database – Best Practice

  - by pinaldave

  Marko Parkkola This article has been submitted by Marko Parkkola, Data systems designer at Saarionen Oy, Finland. Marko is excellent developer and always thinking at next level. You can read his earlier comment which created very interesting discussion here: SQL SERVER- IF EXISTS(Select null from table) vs IF EXISTS(Select 1 from table). I must express my special thanks to Marko for sending this best practice for Enumerations in Relational Database. He has really wrote excellent piece here and welcome comments here. Enumerations in Relational Database This is a subject which is very basic thing in relational databases but often not very well understood and sometimes badly implemented. There are of course many ways to do this but I concentrate only two cases, one which is “the right way” and one which is definitely wrong way. The concept Let’s say we have table Person in our database. Person has properties/fields like Firstname, Lastname, Birthday and so on. Then there’s a field that tells person’s marital status and let’s name it the same way; MaritalStatus. Now MaritalStatus is an enumeration. In C# I would definitely make it an enumeration with values likes Single, InRelationship, Married, Divorced. Now here comes the problem, SQL doesn’t have enumerations. The wrong way This is, in my opinion, absolutely the wrong way to do this. It has one upside though; you’ll see the enumeration’s description instantly when you do simple SELECT query and you don’t have to deal with mysterious values. There’s plenty of downsides too and one would be database fragmentation. Consider this (I’ve left all indexes and constraints out of the query on purpose). CREATE TABLE [dbo].[Person] ( [Firstname] NVARCHAR(100), [Lastname] NVARCHAR(100), [Birthday] datetime, [MaritalStatus] NVARCHAR(10) ) You have nvarchar(20) field in the table that tells the marital status. Obvious problem with this is that what if you create a new value which doesn’t fit into 20 characters? You’ll have to come and alter the table. There are other problems also but I’ll leave those for the reader to think about. The correct way Here’s how I’ve done this in many projects. This model still has one problem but it can be alleviated in the application layer or with CHECK constraints if you like. First I will create a namespace table which tells the name of the enumeration. I will add one row to it too. I’ll write all the indexes and constraints here too. CREATE TABLE [CodeNamespace] ( [Id] INT IDENTITY(1, 1), [Name] NVARCHAR(100) NOT NULL, CONSTRAINT [PK_CodeNamespace] PRIMARY KEY ([Id]), CONSTRAINT [IXQ_CodeNamespace_Name] UNIQUE NONCLUSTERED ([Name]) ) GO INSERT INTO [CodeNamespace] SELECT 'MaritalStatus' GO Then I create a table that holds the actual values and which reference to namespace table in order to group the values under different namespaces. I’ll add couple of rows here too. CREATE TABLE [CodeValue] ( [CodeNamespaceId] INT NOT NULL, [Value] INT NOT NULL, [Description] NVARCHAR(100) NOT NULL, [OrderBy] INT, CONSTRAINT [PK_CodeValue] PRIMARY KEY CLUSTERED ([CodeNamespaceId], [Value]), CONSTRAINT [FK_CodeValue_CodeNamespace] FOREIGN KEY ([CodeNamespaceId]) REFERENCES [CodeNamespace] ([Id]) ) GO -- 1 is the 'MaritalStatus' namespace INSERT INTO [CodeValue] SELECT 1, 1, 'Single', 1 INSERT INTO [CodeValue] SELECT 1, 2, 'In relationship', 2 INSERT INTO [CodeValue] SELECT 1, 3, 'Married', 3 INSERT INTO [CodeValue] SELECT 1, 4, 'Divorced', 4 GO Now there’s four columns in CodeValue table. CodeNamespaceId tells under which namespace values belongs to. Value tells the enumeration value which is used in Person table (I’ll show how this is done below). Description tells what the value means. You can use this, for example, column in UI’s combo box. OrderBy tells if the values needs to be ordered in some way when displayed in the UI. And here’s the Person table again now with correct columns. I’ll add one row here to show how enumerations are to be used. CREATE TABLE [dbo].[Person] ( [Firstname] NVARCHAR(100), [Lastname] NVARCHAR(100), [Birthday] datetime, [MaritalStatus] INT ) GO INSERT INTO [Person] SELECT 'Marko', 'Parkkola', '1977-03-04', 3 GO Now I said earlier that there is one problem with this. MaritalStatus column doesn’t have any database enforced relationship to the CodeValue table so you can enter any value you like into this field. I’ve solved this problem in the application layer by selecting all the values from the CodeValue table and put them into a combobox / dropdownlist (with Value field as value and Description as text) so the end user can’t enter any illegal values; and of course I’ll check the entered value in data access layer also. I said in the “The wrong way” section that there is one benefit to it. In fact, you can have the same benefit here by using a simple view, which I schema bound so you can even index it if you like. CREATE VIEW [dbo].[Person_v] WITH SCHEMABINDING AS SELECT p.[Firstname], p.[Lastname], p.[BirthDay], c.[Description] MaritalStatus FROM [dbo].[Person] p JOIN [dbo].[CodeValue] c ON p.[MaritalStatus] = c.[Value] JOIN [dbo].[CodeNamespace] n ON n.[Id] = c.[CodeNamespaceId] AND n.[Name] = 'MaritalStatus' GO -- Select from View SELECT * FROM [dbo].[Person_v] GO This is excellent write up byMarko Parkkola. Do you have this kind of design setup at your organization? Let us know your opinion. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Best Practices, Database, DBA, Readers Contribution, Software Development, SQL, SQL Authority, SQL Documentation, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• SQL SERVER – Single Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

  - by pinaldave

  In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Single Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Single Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Single Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the single wait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the single wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the single wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

• Oracle Announces New Oracle Exastack Program for ISV Partners

  - by pfolgado

  Oracle Exastack Program Enables ISV Partners to Leverage a Scalable, Integrated Infrastructure to Deliver Their Applications Tuned and Optimized for High-Performance News Facts Enabling Independent Software Vendors (ISVs) and other members of Oracle Partner Network (OPN) to rapidly build and deliver faster, more reliable applications to end customers, Oracle today introduced Oracle Exastack Ready, available now, and Oracle Exastack Optimized, available in fall 2011 through OPN. The Oracle Exastack Program focuses on helping ISVs run their solutions on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud -- integrated systems in which the software and hardware are engineered to work together. These products provide partners with a lower cost and high performance infrastructure for database and application workloads across on-premise and cloud based environments. Leveraging the new Oracle Exastack Program in which applications can qualify as Oracle Exastack Ready or Oracle Exastack Optimized, partners can use available OPN resources to optimize their applications to run faster and more reliably -- providing increased performance to their end users. By deploying their applications on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud, ISVs can reduce the cost, time and support complexities typically associated with building and maintaining a disparate application infrastructure -- enabling them to focus more on their core competencies, accelerating innovation and delivering superior value to customers. After qualifying their applications as Oracle Exastack Ready, partners can note to customers that their applications run on and support Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud component products including Oracle Solaris, Oracle Linux, Oracle Database and Oracle WebLogic Server. Customers can be confident when choosing a partner's Oracle Exastack Optimized application, knowing it has been tuned by the OPN member on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud with a goal of delivering optimum speed, scalability and reliability. Partners participating in the Oracle Exastack Program can also leverage their Oracle Exastack Ready and Oracle Exastack Optimized applications to advance to Platinum or Diamond level in OPN. Oracle Exastack Programs Provide ISVs a Reliable, High-Performance Application Infrastructure With the Oracle Exastack Program ISVs have several options to qualify and tune their applications with Oracle Exastack, including: Oracle Exastack Ready: Oracle Exastack Ready provides qualifying partners with specific branding and promotional benefits based on their adoption of Oracle products. If a partner application supports the latest major release of one of these products, the partner may use the corresponding logo with their product marketing materials: Oracle Solaris Ready, Oracle Linux Ready, Oracle Database Ready, and Oracle WebLogic Ready. Oracle Exastack Ready is available to OPN members at the Gold level or above. Additionally, OPN members participating in the program can leverage their Oracle Exastack Ready applications toward advancement to the Platinum or Diamond levels in the OPN Specialized program and toward achieving Oracle Exastack Optimized status. Oracle Exastack Optimized: When available, for OPN members at the Gold level or above, Oracle Exastack Optimized will provide direct access to Oracle technical resources and dedicated Oracle Exastack lab environments so OPN members can test and tune their applications to deliver optimal performance and scalability on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud. Oracle Exastack Optimized will provide OPN members with specific branding and promotional benefits including the use of the Oracle Exastack Optimized logo. OPN members participating in the program will also be able to leverage their Oracle Exastack Optimized applications toward advancement to Platinum or Diamond level in the OPN Specialized program. Oracle Exastack Labs and ISV Enablement: Dedicated Oracle Exastack lab environments and related technical enablement resources (including Guided Learning Paths and Boot Camps) will be available through OPN for OPN members to further their knowledge of Oracle Exastack offerings, and qualify their applications for Oracle Exastack Optimized or Oracle Exastack Ready. Oracle Exastack labs will be available to qualifying OPN members at the Gold level or above. Partners are eligible to participate in the Oracle Exastack Ready program immediately, which will help them meet the requirements to attain Oracle Exastack Optimized status in the future. Guidelines for Oracle Exastack Optimized, as well as Oracle Exastack Labs will be available in fall 2011. Supporting Quotes "In order to effectively differentiate their software applications in the marketplace, ISVs need to rapidly deliver new capabilities and performance improvements," said Judson Althoff, Oracle senior vice president of Worldwide Alliances and Channels and Embedded Sales. "With Oracle Exastack, ISVs have the ability to optimize and deploy their applications with a complete, integrated and cloud-ready infrastructure that will help them accelerate innovation, unlock new features and functionality, and deliver superior value to customers." "We view performance as absolutely critical and a key differentiator," said Tom Stock, SVP of Product Management, GoldenSource. "As a leading provider of enterprise data management solutions for securities and investment management firms, with Oracle Exadata Database Machine, we see an opportunity to notably improve data processing performance -- providing high quality 'golden copy' data in a reduced timeframe. Achieving Oracle Exastack Optimized status will be a stamp of approval that our solution will provide the performance and scalability that our customers demand." "As a leading provider of Revenue Intelligence solutions for telecommunications, media and entertainment service providers, our customers continually demand more readily accessible, enriched and pre-analyzed information to minimize their financial risks and maximize their margins," said Alon Aginsky, President and CEO of cVidya Networks. "Oracle Exastack enables our solutions to deliver the power, infrastructure, and innovation required to transform our customers' business operations and stay ahead of the game." Supporting Resources Oracle PartnerNetwork (OPN) Oracle Exastack Oracle Exastack Datasheet Judson Althoff blog Connect with the Oracle Partner community at OPN on Facebook, OPN on LinkedIn, OPN on YouTube, or OPN on Twitter

  Read the article

< Previous Page | 330 331 332 333 334 335 336 337 338 339 340 341  | Next Page >