Search Results

Search found 31625 results on 1265 pages for 'private network'.

Page 336/1265 | < Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Significant OS X Finder lag when listing directories/files

  - by Jack Sleight

  I'm experiencing some significant OS X finder lag, that seems to be purely an issue with Finder itself, and not the HD or any other part of OS X (I'll explain below). The lag only appears to be when listing directories/files, where I'm seeing up to twelve or so seconds of lag (the folder opens with a blank list and the spinner going in the bottom right). This happens with both the local SSD and network drives (connected via ethernet or wifi) Browsing both local and network drives in terminal and listing directories is instant I can actually browse files on my NAS from my phone over a 3G connection from the other side of the country faster than Finder can when connected to the local network (madness!) Can anyone help? Thanks.

  Read the article

• Is creating a separate pool for each individual png image in the same class appropriate?

  - by Panzercrisis

  I'm still possibly a little green about object-pooling, and I want to make sure something like this is a sound design pattern before really embarking upon it. Take the following code (which uses the Starling framework in ActionScript 3): [Embed(source = "/../assets/images/game/misc/red_door.png")] private const RED_DOOR:Class; private const RED_DOOR_TEXTURE:Texture = Texture.fromBitmap(new RED_DOOR()); private const m_vRedDoorPool:Vector.<Image> = new Vector.<Image>(50, true); . . . public function produceRedDoor():Image { // get a Red Door image } public function retireRedDoor(pImage:Image):void { // retire a Red Door Image } Except that there are four colors: red, green, blue, and yellow. So now we have a separate pool for each color, a separate produce function for each color, and a separate retire function for each color. Additionally there are several items in the game that follow this 4-color pattern, so for each of them, we have four pools, four produce functions, and four retire functions. There are more colors involved in the images themselves than just their predominant one, so trying to throw all the doors, for instance, in a single pool, and then changing their color properties around isn't going to work. Also the nonexistence of the static keyword is due to its slowness in AS3. Is this the right way to do things?

  Read the article

• Do I need a VPN to secure communication over a T1 line?

  - by Seth

  I have a dedicated T1 line that runs between my office and my data center. Both ends have public IP addresses. On both ends, we have a T1 routers which connect to SonicWall firewalls. The SonicWalls do a site-to-site VPN and handle the network translation, so the computers on the office network (10.0.100.x) can access the servers in the rack (10.0.103.x). So the question: can I just add a static route to the SonicWalls so each network can access each other with out the VPN? Are there security problems (such as, someone else adding the appropriate static route and being able to access either the office or the datacenter)? Is there another / better way to do it? The reason I'm looking at this is because the T1 is already a pretty small pipe, and having the VPN overhead makes connectivity really slow.

  Read the article

• Methodology To Determine Cause Of User Specific Error

  - by user3163629

  We have software that for certain clients fails to download a file. The software is developed in Python and compiled into an Windows Executable. The cause of the error is still unknown but we have established that the client has an active internet connection. We suspect that the cause is due to the clients network setup. This error cannot be replicated in house. What technique or methodology should be applied to this kind of specific error that cannot be replicated in house. The end goal is to determine the cause of this error so we can move onto the solution. For example; Remote Debugging: Produce a debug version of the software and ask the client to send back a debug output file. This involves alot of time (back and forth communication) and requires the client to work and act in a timely manor to be successful. In-house debugging: Visit the client and determine their network setup, etc. Possibly develop a series of script tests before hand to run on the clients computer under the same network. Other methodologies and techniques I am not aware of?

  Read the article

• How to implement child-parent aggregation link in C++?

  - by Giorgio

  Suppose that I have three classes P, C1, C2, composition (strong aggregation) relations between P <>- C1 and P <>- C2, i.e. every instance of P contains an instance of C1 and an instance of C2, which are destroyed when the parent P instance is destroyed. an association relation between instances of C1 and C2 (not necessarily between children of the same P). To implement this, in C++ I normally define three classes P, C1, C2, define two member variables of P of type boost::shared_ptr<C1>, boost::shared_ptr<C2>, and initialize them with newly created objects in P's constructor, implement the relation between C1 and C2 using a boost::weak_ptr<C2> member variable in C1 and a boost::weak_ptr<C1> member variable in C2 that can be set later via appropriate methods, when the relation is established. Now, I also would like to have a link from each C1 and C2 object to its P parent object. What is a good way to implement this? My current idea is to use a simple constant raw pointer (P * const) that is set from the constructor of P (which, in turn, calls the constructors of C1 and C2), i.e. something like: class C1 { public: C1(P * const p, ...) : paren(p) { ... } private: P * const parent; ... }; class P { public: P(...) : childC1(new C1(this, ...)) ... { ... } private: boost::shared_ptr<C1> childC1; ... }; Honestly I see no risk in using a private constant raw pointer in this way but I know that raw pointers are often frowned upon in C++ so I was wondering if there is an alternative solution.

  Read the article

• How can I improve performance over SMB/CIFS for an application that has poor write speeds?

  - by Jeremy

  I have a third party application that reads several large files and generates a third large file. Its performance is quite good when the generated file is stored on "local storage", i.e. either a direct attached or iSCSI-based disk. The source files that are read can be stored remotely on our NAS and accessed via SMB with little effect on performance. However, if we attempt to write the target file to any kind of SMB/CIFS share (Samba or Windows Server) the performance drops almost ten-fold. This is unacceptably slow in our case. Writing files to network shares is not otherwise slow. I can copy large files to SMB shares and get great performance - near what I would expect is possible given the disks and network in question. I have a theory that this application's problem with SMB shares has something to do with a lack of write caching over the share and perhaps lots of network roundtrips. Is this possible and is there anything that can be done about it?

  Read the article

• psloggedon timeout question.

  - by user60707

  Hi guys, I have a list of machine names from my network that I have put in a batchfile to run through the list and show me who is logged onto each. psloggedon \machineA psloggedon \machineB psloggedon \machineC psloggedon \machineD psloggedon \machineE psloggedon \machineF Psloggedon works fine, however when it hits a machine that isnt actually on the network, it hangs for a good 30 - 60 seconds before moving onto the next machine...I was just wondering if there was any way to speed this up so that if it hits a machine that isnt on the network, it moves onto the next machine in the list much quicker. I have read in other places that this could be possible by adding a ping -n loop into the command but im not sure how to get that to work? any ideas guys? Many thanks in advance. Jimmy

  Read the article

• Configure ubuntu 12.10 to share internet through second NIC with subnetwork

  - by Dan Smith

  I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

  Read the article

• Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

  - by tomdee

  I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

  Read the article

• How to auto-mount a copied encrypted home

  - by LedZ

  How can I auto-mount and use my encrypted home that I copied to another partition on the same hard disk? I'm running Ubuntu 11.10. My encrypted home is on sda1. There I've 2 users: userA and userB. Another partition is sda3 on which I have some other Data. BTW, sda1 is formatted as EXT4, sda3 is formatted as EXT3. I did the following: I logged out from GUI (Gnome) and changed (using Ctrl+Alt+F1) to the shell. From there I logged in, changed to sudo (using sudo -s) . After then I created a new mountpoint (tmp) under /mnt (mkdir /mnt/tmp) mounted /dev/sda3 on that mountpoint /mnt/tmp (mount /dev/sda3 /mnt/tmp) copied my encrypted /home to /mnt/tmp using rsync (rsync --acvxASXH --progress --stats /home/ /mnt/tmp/). After the “copy-procedure” I looked to my “new home” in /mnt/tmp and there I found the following 3 folders: userA, userB, .ecryptfs My structure for /dev/sda3 mounted on /mnt/tmp looks like the following (userB in ecryptfs I've not listed): -userA ¦ +userB ¦ +.ecryptfs ¦ +userA ¦ + auto-mount ¦ + auto-umount ¦ + Private.mnt ¦ + Private.sig ¦ + wrapped-passphrase ¦ + .wrapped-passphrase.recorded ¦ + .Private + (encrypted file_1) + (encrypted file_2) + (encrypted file_n) Now I would like that this copy of the original home-directory should act with the same behavior as the original home-directory means, that it should be auto-mounted at reboot and give me access to my unencrypted files and after logout all my files should be encrypted again. Any suggestions?

  Read the article

• Track sales and commission with third-party tool

  - by Andrew

  I have a clothing website where I link to various clothing retailers. I have reached an agreement with one of the retailers whereby they will pay a commission to us for every sale they make from traffic that was referred by our site. I need a mechanism for tracking how much commission should be paid to us, that involves as little work as possible to implement from their side. We both have Google Analytics. Option 1: They record a goal in their GA account whenever someone makes a purchase on their site. They see how many completed goals are marked as referral traffic from our site and calculate commission accordingly. The problem with this is that the whole process of calculating and paying commission will be manual. They will need to frequently check how many sales were generated by referral traffic from our site, and probably we will have to chase them for commission payments. Also - since we won't have access to their GA data - we will need to trust that they report all sales accurately. Option 2: Sign them up to an affiliate network like Commission Junction or Google's Affiliate Network, and connect to them through this network. The problem with this solution is that it seems too heavyweight; ideally we don't want to ask a retailer to go through the whole sign up process just to deal with us and pay us commission. I am assuming that there must be some lightweight service that tracks the number of sales by one site and pays commission accordingly to the other site, where the sign up and installation procedure is simple and fast.

  Read the article

• How do I remove/uninstall a corporate VPN?

  - by Metro Smurf

  I have a corporate VPN installed on one of my Windows XP systems that I'd like to completely uninstall. There are no programs listed in the add/remove programs dialog matching the corporate VPN name or similar. I can find the VPN being launched from here: C:\Documents and Settings\All Users\Application Data\Microsoft\Network\Connections\Cm\<Company Name> I can see the VPN connection under network connections: Name Type Device Name Connection Manager ------------------- Connection to <Company Name> Connection Manger WAM Miniport (PPTP) Do I just need to delete the connection from Network Connections? And delete the directory? Or?

  Read the article

• iptables question

  - by RubyFreak

  i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

  Read the article

• Windows user cannot connect via application, but can via Remote Desktop

  - by C. Ross

  I have an application (ASG-Zena) giving an 1385 error (Logon failure: the user has not been granted the requested logon type at this computer) when trying to run a batch job. I have checked on "Access this computer from the network" includes Everyone and Administrators and many others. "Deny access to this computer from the network" make sure that Guest is not listed there. If you still have problems, then maybe make sure that nothing is listed there. Administrative tools...local security policy..security options "Network access sharing and security model for local accounts" there are 2 options either classic or 'guest only'. Mine is set to classic. (These diagnostics come from this post) The account in question is added to the Administrator group on this computer. I know the login is valid because I regularly login to the server via remote Desktop. What other settings should I check?

  Read the article

• Is encoding needed in this decryption?

  - by Lijo

  I have a Encryption – Decryption scenario as shown below. //[Clear text ID string as input] -- [(ASCII GetByte) + Encoding] -- [Encrption as byte array] -- [Database column is in VarBinary] -- [Pass byte[] as VarBinary parameter to SP for comparison] //[ID stored as VarBinary in Database] -- [Read as byte array] -- [(Decrypt as byte array) + Encoding + (ASCII Get String)] -- Show as string in the UI My question is in the decryption scenario. After decryption I get a byte array. I am doing an encoding (IBM037) after that. Is it correct? Is there something wrong in the flow shown above? private static byte[] GetEncryptedID(string id) { Interface_Request input = new Interface_Request(); input.RequestText = Encodeto64(id); input.RequestType = Encryption; ProgramInterface inputRequest = new ProgramInterface(); inputRequest.Test_Trial_Request = input; using (KTestService operation = new KTestService()) { return ((operation.KTrialOperation(inputRequest)).Test_Trial_Response.ResponseText); } } private static string GetDecryptedID(byte[] id) { Interface_Request input = new Interface_Request(); input.RequestText = id; input.RequestType = Decryption; ProgramInterface request = new ProgramInterface(); request.Test_Trial_Request = input; using (KTestService operationD = new KTestService()) { ProgramInterface1 response = operationD.KI014Operation(request); byte[] decryptedValue = response.ICSF_AES_Response.ResponseText; Encoding sourceByteFormat = Encoding.GetEncoding("IBM037"); Encoding destinationByteFormat = Encoding.ASCII; //Convert from one byte format to other (IBM to ASCII) byte[] ibmEncodedBytes = Encoding.Convert(sourceByteFormat, destinationByteFormat,decryptedValue); return System.Text.ASCIIEncoding.ASCII.GetString(ibmEncodedBytes); } } private static byte[] EncodeTo64(string toEncode) { byte[] dataInBytes = System.Text.ASCIIEncoding.ASCII.GetBytes(toEncode); Encoding destinationByteFormat = Encoding.GetEncoding("IBM037"); Encoding sourceByteFormat = Encoding.ASCII; //Convert from one byte format to other (ASCII to IBM) byte[] asciiBytes = Encoding.Convert(sourceByteFormat, destinationByteFormat, dataInBytes); return asciiBytes; }

  Read the article

• Impacting the Future through Collaboration at Alliance 14

  - by Jeb Dasteel-Oracle

  We’re hearing good things about the Alliance 14 conference held in Las Vegas by the Higher Education Users Group (HEUG) back in March. For those of you who aren’t familiar with Alliance 14 conferences, they are global events dedicated to enhancing and educating its members and the world on how higher educational institutions can utilize Oracle applications to change how they do business. The HEUG is an all-volunteer organization made up of individuals who collaborate with Oracle as part of the evolving higher education industry. Conference participants network with peers from other institutions (regionally and globally) to share the challenges; discuss solutions and ideas, and collaborate on HEUG strategic initiatives. The HEUG enables each institution to be a part of the ever-changing Oracle landscape. Watch the video below and hear directly from the attendees about their experience with Oracle and how being part of the HEUG has allowed them to  collaborate with one of their most importance resources... and with each other. Oracle is committed to fostering a strong and independent network of user groups worldwide. Currently over 900+ groups provide dynamic forums for customers to share information, experiences and expertise. If you’re interested in more information or joining an Oracle User Group, click and become part of a vibrant network of engaged users finding the best ways to get the most value from their Oracle investment and collaborating to provide a unified feedback voice to Oracle. Catch you next time, Jeb

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Windows VPN not authenticating from ADSL to Wireless link

  - by deanvz

  I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

  Read the article

• What are the advantages of OSPF vs nexthop self with iBGP?

  - by Matt Hamilton

  Assuming I have a fairly small network internally, but I have 4 routers each connected out to a different network. The routers are all sat next to each other connected via a switch. Each router uses BGP to speak to the outside networks. There is an iBGP mesh for each router to exchange the routes internally it knows about from each external network. The usual setup is to use OSPF to distribute the connected routes, as the routes via iBGP will still have the next hop set to their original value. What is the advantage of using OSPF in this scenario versus simply using 'set nexthop self' on the routes?

  Read the article

• Windows 7 PPTP VPN problem

  - by Marco Martins

  Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• How to minimize the usage of static variables and objects

  - by Peter Penzov

  I'm trying to implement this JavaFX code where I want to call remote Java class and pass boolean flag: final CheckMenuItem toolbarSubMenuNavigation = new CheckMenuItem("Navigation"); toolbarSubMenuNavigation.setOnAction(new EventHandler<ActionEvent>() { @Override public void handle(ActionEvent e) { //DataTabs.renderTab = toolbarSubMenuNavigation.isSelected(); DataTabs.setRenderTab(toolbarSubMenuNavigation.isSelected()); // call here the getter setter and send boolean flag System.out.println("subsystem1 #1 Enabled!"); } }); Java class which I want to call: public class DataTabs { private static boolean renderTab; // make members *private* private static TabPane tabPane; public static boolean isRenderTab() { return DataTabs.renderTab; } public static void setRenderTab(boolean renderTab) { DataTabs.renderTab = renderTab; tabPane.setVisible(renderTab); } // somewhere below // set visible the tab pane TabPane tabPane = DataTabs.tabPane = new TabPane(); tabPane.setVisible(renderTab); } This implementation works but I want to optimize it to use less static variables and objects. Can you tell me which sections of the code how can be optimized?

  Read the article

• recent unreliable wireless connection

  - by gabkdlly

  Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

  Read the article

< Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >