Search Results

Search found 31625 results on 1265 pages for 'private network'.

Page 334/1265 | < Previous Page | 330 331 332 333 334 335 336 337 338 339 340 341  | Next Page >

• I am trying to set up a ubuntu sever 12.04 on my machine

  - by Jseb

  I am trying to set up a server on my home network which will eventually host rails. I am not great in linux server and i try to follow the prompt. I did succesfully get to a black screen which then prompts me to a username then password to then do anything ( assuming). However here what i try to do I kinda fellow his tutorial http://www.ubuntugeek.com/step-by-step-ubuntu-11-04-natty-lamp-server-setup.html but however the command where not 100% like him not in same order but same idea. Then i want to install ubuntu server with gui here the command i try with sudo apt-get upgrade sudo apt-get install ubuntu-desktop Which however give me the following error Err http... inRelease w Failed to fetch ht... So been ignored if i try the desktop one i get E: unable to locate package ubuntu E: unable to locate package desktop So i am assuming i am not connected to the internet, so i try the following command sudo vi /etc/network/interfaces here the output it gives me and i know my gateway on my laptop is 192.168.1.1 address: 192.168.1.148 netmask: 255.255.255.0 network: 192.168.1.0 broadcasts: 192.168.1.255 gateway: 192.168.1.1 Btw i do not know the command to get out of vi and saving it. Err http://us.archive.ubuntu.com precises InRelease Err http://us.archive.ubuntu.com precises-updates InRelease Err http://us.archive.ubuntu.com precises-backports InRelease Reading package lists... Done W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise/InRelease W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-updates/InRelease W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-backport/InRelease

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Creating user UI using Flixel

  - by Jamie Read

  I am new to game development but familiar with programming languages. I have started using Flixel and have a working Breakout game with score and lives. What I am trying to do is add a Start Screen before actually loading the game. I have a create function that adds all the game elements to the stage: override public function create():void // all game elements { How can I add this pre-load Start Screen? I'm not sure if I have to add in the code to this create function or somewhere else and what code to actually add. Eventually I would also like to add saving, loading, options and upgrades too. So any advice with that would be great. Here is my main game.as: package { import org.flixel.*; public class Game extends FlxGame { private const resolution:FlxPoint = new FlxPoint(640, 480); private const zoom:uint = 2; private const fps:uint = 60; public function Game() { super(resolution.x / zoom, resolution.y / zoom, PlayState, zoom); FlxG.flashFramerate = fps; } } } Thanks.

  Read the article

• Amazon EC2, fastest way to get a node into an existing cluster

  - by imaginative

  I'm new to Amazon AWS. A lot of the time I hear about people folks spawning instances and almost instantly putting them behind a load balancer and into an existing cluster. In the traditional world of managed machines, this would include provisioning hardware, installing an OS, configuring the network on the machine and once the network is available, use a tool of your choice such as CFengine, Puppet or Chef to bootstrap the machine based on its class. It seems like there are "shortcuts" that are able to get a server of a particular class up and running in Amazon EC2. If I have a particular stack running on my server, such as erlang, tomcat6 etc.. what's the fastest way to get these up and running and hooked into Amazon's load balancer? From network, to software stack to kernel tuning? Is it a combination of creating an AMI then running a tool like Puppet against the new instance? Any idea

  Read the article

• mystery Internet traffic to port 445

  - by Ben Collver

  Recently, I noticed traffic from the office network to TCP port 445 on the Internet [a]. Below are the Linux firewall log entries to Facebook's network [b] and Google's network [c]. I would like to identify the source of this traffic. My first guess is that Facebook and Google might be using multiple TCP ports for SSL load balancing. However, I could not confirm this based on the web proxy logs. What else might it be? [a] http://support.microsoft.com/kb/204279 [b] Sep 4 08:30:03 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.131 DST=69.171.237.34 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=14287 DF PROTO=TCP SPT=51711 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0 [c] Aug 28 06:02:41 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.115 DST=173.194.33.47 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=4558 DF PROTO=TCP SPT=49294 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0

  Read the article

• OpenVPN to connect remote networks, peer to peer instead of client/server possible?

  - by John Robertson

  I would like to connect two remote networks using OpenVPN. I am very new to this we are very small and don't have a sys/network admin. What are the possible setups to have both networks both live on a common LAN via OpenVPN? I would prefer to use the UDP peer model rather than client/server. Is there a way to set that up instead? I can't see how because no computer on existing network A has a routable address to any computer on existing network B and vice versa.

  Read the article

• dhcpd pool exhaustion - What's the result?

  - by jarmund

  I have a DHCP server that serves leases to several houndred, maybe up to a thousand, different clients on an average day. The pool consists of 242 IPs, and due to the highly dynamic nature of the network, it's enough 99% of the time (most devices are gone from the network in a few minutes), despite having a lease time of 3600. Now, imagine if more clients than that connect to the network during an hour. The sollution is obvious: Decrease lease time, or increase the DHCP pool, however, what i would like to know: What happens when dhcpd has exhausted the pool? Are new DHCP requests simply ignored?

  Read the article

• Cannot login in account with encrypted home after update from 11.04 to 11.10

  - by martin

  After upgrading from ubuntu 11.04 to 10.10 I cannot access my encrypted home partition anymore. I can login, however all data stays encrypted. ecryptfs-mount-private gives: ERROR: Encrypted private directory is not setup properly Any idea how to fix this? Update I have several kernels installed (after the upgrade my menu.lst looks like this: http://paste.org/pastebin/view/35591) the problem is the same for all kernels. Booting from 2.6.32-27-generic and adduser --encrypt-home tes gives: Adding user `tes' ... Adding new group `tes' (1008) ... Adding new user `tes' (1007) with group `tes' ... Creating home directory `/home/tes' ... Setting up encryption ... ************************************************************************ YOU SHOULD RECORD YOUR MOUNT PASSPHRASE AND STORE IT IN A SAFE LOCATION. ecryptfs-unwrap-passphrase ~/.ecryptfs/wrapped-passphrase THIS WILL BE REQUIRED IF YOU NEED TO RECOVER YOUR DATA AT A LATER TIME. ************************************************************************ Error: Your kernel does not support filename encryption ERROR: Could not add passphrase to the current keyring adduser: `/usr/bin/ecryptfs-setup-private -b -u tes' returned error code 1. Exiting.

  Read the article

• How to achieve reliable Gigabit Ethernet Link with my Acer Aspire Revo R3610?

  - by The Operator

  I want to stream HD movies over my wired Gigabit LAN from my PC to my Acer Aspire Revo R3610. It's connected with a 3ft Cat5e patch cable to my Netgear GS605v2 Switch. The PC acting as File Server is connected at 1Gbps to the Switch. Network driver options are set to defaults, including automatic speed/duplex negotiation on both machines. The Revo will not connect to my Network Switch at 1Gbps - the OS reports that it reverts to 100Mbps either shortly after connection or immediately upon connection. Through a process of elimination (trying different drivers, patch cables, ports on the switch, and other 1Gbps-capable devices connected to the Network switch which successfully achieve 1Gbps links and performance) I have drawn the conclusion there is either a Hardware or Software (Driver) issue with the Revo itself. I have performed tests using Windows 7 and Ubuntu 9.10. Can anyone offer insight on Gigabit Ethernet with the Revo?

  Read the article

• Pattern for a class that does only one thing

  - by Heinzi

  Let's say I have a procedure that does stuff: void doStuff(initalParams) { ... } Now I discover that "doing stuff" is quite a compex operation. The procedure becomes large, I split it up into multiple smaller procedures and soon I realize that having some kind of state would be useful while doing stuff, so that I need to pass less parameters between the small procedures. So, I factor it out into its own class: class StuffDoer { private someInternalState; public Start(initalParams) { ... } // some private helper procedures here ... } And then I call it like this: new StuffDoer().Start(initialParams); or like this: new StuffDoer(initialParams).Start(); And this is what feels wrong. When using the .NET or Java API, I always never call new SomeApiClass().Start(...);, which makes me suspect that I'm doing it wrong. Sure, I could make StuffDoer's constructor private and add a static helper method: public static DoStuff(initalParams) { new StuffDoer().Start(initialParams); } But then I'd have a class whose external interface consists of only one static method, which also feels weird. Hence my question: Is there a well-established pattern for this type of classes that have only one entry point and have no "externally recognizable" state, i.e., instance state is only required during execution of that one entry point?

  Read the article

• Mikrotik server networks and Cain & Abel

  - by user269742

  I'm connected to the internet via a mikrotik server network. Recently, I read about that scaring application named Cain & Abel and all the capabilities it offered for malicious users. I don't know if anyone on my network is using or even aware of such application but my questions are: 1- How to protect myself from this program? 2- How to know if someone using such application against me? 3- Is Tor Bundle capable of protecting me from Cain & Abel? 4- If I filled my e-mail password via SSL page, Can Cain & Abel collect it? 5- Is it safe to use SKYPE or Yahoo Messenger voice chat if some one using Cain & Abel on my network?

  Read the article

• Too many processes?

  - by Mophily

  VMware Fusion v3.0.1 One vm for Windows XP, converted and recently expanded the disk size. Mac OS X 10.5.8, 2 x 3 GHz dual-core intel xeon machine. Immediately after booting, and before VMware Fusion is launched, the Activity Monitor shows eight processes associated with "vm". What caught my eye is the duplicates: netifup and dhcpd. I noticed this while trying to re-establish network connectivity after the upgrade to 3.0.1. I am not sure when the network connection was clobbered, so I cannot say it happend during the upgrade. Is eight processes typcial? I expect about six, as listed in other notes and documents on the web site. Could this be related to the failure to connect to the network?

  Read the article

• Cisco, How to do a subnetting scheme using VLSM and RIP-2?

  - by Andrei T. Ursan

  I'm studying for my CCNA exam and I have to create a VLSM scheme using RIP-2 for the following requirements: (this is an exercise) Use the class C network 192.168.1.0 network for your point-to-point connections Using the Class A network 10.0.0.0, plan for the following number of hosts in each location: New York: 1000 Chicago: 500 Los Angeles: 1000 On the LAN and point-to-point connections, select subnet masks that use the smallest ranges of IP addresses possible given the above requirements. In all cases, use the lowest possible subnet numbers. Subnet zero is allowed. My guess is the following: New York: S0/0 192.168.1.1 /24 Fa0/0 10.1.0.1 netmask 255.255.248.0 - because we need 1000 hosts Chicago: S0/0 192.168.1.2 /24 Fa0/0 10.2.0.1 netmask 255.255.252.0 (for 500 hosts) Los Angeles: S0/0 192.168.2.3 /24 Fa0/0 10.3.0.1 netmask 255.255.248.0 (for 1000 hosts) Is this a good configuration? I'm reading the CCNA book but not everything is very clear, so I said to do some exercises... Thank you!

  Read the article

• How to make sure Windows PC is reasonably secure?

  - by Coder

  I'm not much of a network and network security expert, but I need to add an existing Windows PC to a network with always on connection. The problem is, I have no idea if the PC is really clean, and, actually, no knowledge to check it. I scanned the PC with Process Explorer to verify if all running processes are signed, ran an AVG scan, but this is where my knowledge ends. IIRC, there can be bad code attached to svchost or something, bad drivers, and so on, but I have no idea how to check all those things. Reformatting the PC is unfeasible as of now. Are there any suggestions on what I could do?

  Read the article

• PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

  - by lcbrevard

  When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

  Read the article

• Configure Windows Routes for VPN

  - by Florin Sabau

  I have a Virtual PC/VMWare machine that runs Windows Server 2003. This virtual machine uses an IPSec VPN client program to connect to a remote network. I configured the virtual machine to have 2 NICs: NAT - to be used by the VPN Client to access the remote network Host only - to be able to access the virtual machine from the host The reason I have this setup is because I want to be able to access some remote network from the host machine. I could've installed the VPN client on the host machine, but the host runs Windows 7 and the client doesn't support it. The problem: although the virtual machine is normally reachable (ping + http access), as soon as the VPN client is started, neither of the NIC addresses are reachable anymore. I'm wondering if it is a routing problem that needs to be addressed? How do routing/VPN client connection affect the ability of the server to respond to client requests from the host?

  Read the article

• Why is wireless slow with Atheros AR9285?

  - by Luke

  I know there are many posts like this, however none of the fixes I have found have worked. I had the issue on 11.04, and after having no luck fixing it decided to try 12.04 however this has not fixed the problem. I'm using a Lenovo IdeaPad, the network card is a Atheros Communications AR9285. edit add outputs: sudo iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"NETGEAR-PLOW" Mode:Managed Frequency:2.437 GHz Access Point: E0:91:F5:7D:1B:BA Bit Rate=65 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:77 Invalid misc:63 Missed beacon:0 eth0 no wireless extensions. lspci -nnk | grep -iA2 net 06:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Lenovo Device [17aa:30a1] Kernel driver in use: ath9k -- 07:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 Thanks

  Read the article

• Linksys EA3500 : use WAN port as WAN + LAN possible?

  - by Dough

  I'm waiting for deliver of a Linksys EA3500 router. I was wondering if it was possible to get the WAN port act as normal WAN port (Internet IP) + LAN switch ? My problem is that my Internet box is in a room with NAS and PC, and the router will be in another room with TV, PS3 and PC. The Internet box have a 4 port Gigabit switch so one cable will plug from there to the router's WAN in the other room. The router will get the Internet IP from the Internet box, but will it be possible to have private network through this link too ? I could have a first network between the Internet box and the router, and another network form router and devices but that will do double NAT for nothing... Thanks for reading me and your help !

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system?

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it)

  Read the article

• Automatically updating routing table on server

  - by bramp

  I have a LAN with three routers on it, one connected to the Internet, one VPN router connected to a few remote sites, and a final route connected to a private network (using BGP to get prefix advertisements). On the same LAN I have multiple Linux servers which needs access to the networks behind each router. I have achieved this by configuring static routes on the server, pointing the different network prefixes to the correct router. This has worked well, but every time we connect to a new remote VPN, we have to change all the servers to be aware that the network is now accessible via the VPN, and not via the default Internet route. What I want is a way to automatically update the routes on all of the servers, when the route is added to a routers. Now, I could install Quagga or something similar on all the servers to receive router advertisements, but that seems like overkill. So my question is what is the easiest/simpliest way to update the routing tables on the server automatically, and what protocol is best suited for this purpose. thanks

  Read the article

• Making internal website available publicly (Win 2008 Server)

  - by endigo

  I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

  Read the article

• Default gateway is in different subnet. How to configure in RHEL6.2

  - by Dmytro Leonenko

  I have two subnets routed to my server from ISP. I have only one gateway ip. The gateway is on the same VLAN as my IP address. For example netowrk 1 is 1.0.0.0/24 and network 2 is 2.0.0.0/24. Both are routed to eth0 by my ISP. Gateway is 1.0.0.1. My host ip is 2.0.0.1/24 (eth0) So I can configure default gateway manually with ip route add default dev eth0 ip route add default via 1.0.0.1 and then internet connection works properly. How do I configure it in /etc/sysconfig/network-scripts/ifcfg-eth0 ? I tried to set GATEWAY=1.0.0.1 but it doesn't work. Tried to set GATEWAY and GATEWAYDEV in /etc/sysconfig/network and it does only what first command from listing above do.

  Read the article

• Relative encapsulation design

  - by taher1992

  Let's say I am doing a 2D application with the following design: There is the Level object that manages the world, and there are world objects which are entities inside the Level object. A world object has a location and velocity, as well as size and a texture. However, a world object only exposes get properties. The set properties are private (or protected) and are only available to inherited classes. But of course, Level is responsible for these world objects, and must somehow be able to manipulate at least some of its private setters. But as of now, Level has no access, meaning world objects must change its private setters to public (violating encapsulation). How to tackle this problem? Should I just make everything public? Currently what I'm doing is having a inner class inside game object that does the set work. So when Level needs to update an objects location it goes something like this: void ChangeObject(GameObject targetObject, int newX, int newY){ // targetObject.SetX and targetObject.SetY cannot be set directly var setter = new GameObject.Setter(targetObject); setter.SetX(newX); setter.SetY(newY); } This code feels like overkill, but it doesn't feel right to have everything public so that anything can change an objects location for example.

  Read the article

• When connected through a router, a new gateway appears, and I lose my internet connection.

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

  Read the article

• I don't know how to connect to the internet

  - by Michiel

  I'm having some trouble finding an answer to my problem. I have a dell desktop (studio hybrid) and i have windows vista on it. The internet on windows vista works great, no problem. But now i downloaded Ubuntu 11.10 and I'm having problems. I can't find how to connect to my wireless network, when i click the network icon, it shows a list of things but I can only click 'enable wireless network' or something like that and 'edit connections'. But in this list it also says ( in a grey collor and i can't click it ) : 'No wireless connection, device not ready (firmware missing)" Or something like that. Now i tried several things i read on the internet (using my vista OS cause i can't use ubuntu for the internet, which is really enoying). But none of them helped me. I would like someone to tell me what my problem is or what information I have to give you to get an answer. So tell me if i have to edit a connection, or tell me how i have to get the wireless connection to work and to repair the 'firmware missing problem'. I hope someone can/is willing to help me. Bye

  Read the article

< Previous Page | 330 331 332 333 334 335 336 337 338 339 340 341  | Next Page >