Search Results

Search found 8755 results on 351 pages for 'triple boot'.

Page 336/351 | < Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >

  • Intermittent internet connectivity

    - by Rob Oplawar
    UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

    Read the article

  • Dual monitor not working completely in 12.10 after upgrade

    - by Mark Baldridge
    At 12.04, dual monitors worked perfectly. After upgrading to 12.10, the primary monitor works, the second monitor only partly works. I am sure there is some difference between the releases that I have missed setting properly. System settings - Displays show both correctly as Acer 22" monitors at 1680x1050 (16:10). An icon on monitor 2 is present, but elongated; almost an artifact, since other icons on the primary screen are absent, but this one icon is there on th second monitor. Selecting the icons on both screens exist. Painting is weird on monitor 2. Launcher exists and works on both screens, but even with sticky edges off, the cursor stops at the left edge of monitor 2. Clicking on text editor on screen 2 launcer will launch gedit there. If I drag it, it leaves a trail of after images like repaint is failing. If I drive the cursor on the launcher, the help tags like "LibreOffice Writer" appear, but stay on screen unless I drag the active gedit window over them. Then part of the help bubbles are overwritten, leaving behind after images of the gedit window on screen. What is really fascinating is that the System settings - Displays is now ignoring monitor selection, after allowing it earlier. Just before this, the help popup which said "Select a monitor to change its properties; drag to rearrange its placement" actually let me do that. Maybe a trick of where I grab the edge of the monitor in the Displays setting. I just found a working handle. When I drag monitor 1 to the right of monitor 2, "Apply" and confirm, both monitors work normally (although the right monitor lets the cursor slide off the right edge onto the left edge of monitor 1 - which sounds correct). Painting of windows does not leave an after image. However, success is only temporary. The setting survives the reboot, but painting on the left monitor, now monitor 2, now replicates the issues from before. The after image of the gedit window and the small window for "Are you sure you want to close all programs and restart the computer?" are still on monitor 2 (on the left now), even though they are not real windows, nor do they have processes behind them. Curiously, in Displays, the "green" monitor on the left in the display window is matched by the right monitor color in the monitor upper left corner. Probably makes sense as the one on the right is now monitor 1. If I repeat the "drag the left monitor to the right of the right monitor on the "Displays" window, things are oriented properly, with no display artifacts as I drag windows around either screen. Also the description bubbles that pop up are overwritten on both screens, so none of those artifacts either. This goodness does not survive a reboot, however. Have not tried logging out and back in. All of this after positing that the motherboard VGA and HDMI ports could have been the issue. So, I installed an e-GeForce 7600 GT Dual DVI (I know the web thinks it is not DVI, but VGA, but the connectors are DVI). No change to the weird behavior. The good parts continue to work, the weirdness also works, and swapping monitor positions seems to cure the issue. So, is there a setting I have missed? Given "swapping" monitor 1 and 2 on the System Settings... - Displays makes it work, just not across boot, I suspect so.

    Read the article

  • Getting Started with Cloud Computing

    - by juanlarios
    You’ve likely heard about how Office 365 and Windows Intune are great applications to get you started with Cloud Computing. Many of you emailed me asking for more info on what Cloud Computing is, including the distinction between "Public Cloud" and "Private Cloud". I want to address these questions and help you get started. Let's begin with a brief set of definitions and some places to find more info; however, an excellent place where you can always learn more about Cloud Computing is the Microsoft Virtual Academy. Public Cloud computing means that the infrastructure to run and manage the applications users are taking advantage of is run by someone else and not you. In other words, you do not buy the hardware or software to run your email or other services being used in your organization – that is done by someone else. Users simply connect to these services from their computers and you pay a monthly subscription fee for each user that is taking advantage of the service. Examples of Public Cloud services include Office 365, Windows Intune, Microsoft Dynamics CRM Online, Hotmail, and others. Private Cloud computing generally means that the hardware and software to run services used by your organization is run on your premises, with the ability for business groups to self-provision the services they need based on rules established by the IT department. Generally, Private Cloud implementations today are found in larger organizations but they are also viable for small and medium-sized businesses since they generally allow an automation of services and reduction in IT workloads when properly implemented. Having the right management tools, like System Center 2012, to implement and operate Private Cloud is important in order to be successful. So – how do you get started? The first step is to determine what makes the most sense to your organization. The nice thing is that you do not need to pick Public or Private Cloud – you can use elements of both where it makes sense for your business – the choice is yours. When you are ready to try and purchase Public Cloud technologies, the Microsoft Volume Licensing web site is a good place to find links to each of the online services. In particular, if you are interested in a trial for each service, you can visit the following pages: Office 365, CRM Online, Windows Intune, and Windows Azure. For Private Cloud technologies, start with some of the courses on Microsoft Virtual Academy and then download and install the Microsoft Private Cloud technologies including Windows Server 2008 R2 Hyper-V and System Center 2012 in your own environment and take it for a spin. Also, keep up to date with the Canadian IT Pro blog to learn about events Microsoft is delivering such as the IT Virtualization Boot Camps and more to get you started with these technologies hands on. Finally, I want to ask for your help to allow the team at Microsoft to continue to provide you what you need. Twice a year through something we call "The Global Relationship Study" – they reach out and contact you to see how they're doing and what Microsoft could do better. If you get an email from "Microsoft Feedback" with the subject line "Help Microsoft Focus on Customers and Partners" between March 5th and April 13th, please take a little time to tell them what you think. Cloud Computing Resources: Microsoft Server and Cloud Computing site – information on Microsoft's overall cloud strategy and products. Microsoft Virtual Academy – for free online training to help improve your IT skillset. Office 365 Trial/Info page – get more information or try it out for yourself. Office 365 Videos – see how businesses like yours have used Office 365 to transition to the cloud. Windows Intune Trial/Info – get more information or try it out for yourself. Microsoft Dynamics CRM Online page – information on trying and licensing Microsoft Dynamics CRM Online. Additional Resources You May Find Useful: Springboard Series Your destination for technical resources, free tools and expert guidance to ease the deployment and management of your Windows-based client infrastructure. TechNet Evaluation Center Try some of our latest Microsoft products for free, Like System Center 2012 Pre-Release Products, and evaluate them before you buy. AlignIT Manager Tech Talk Series A monthly streamed video series with a range of topics for both infrastructure and development managers. Ask questions and participate real-time or watch the on-demand recording. Tech·Days Online Discover what's next in technology and innovation with Tech·Days session recordings, hands-on labs and Tech·Days TV.

    Read the article

  • Cannot get ATI Drivers installed

    - by bittoast67
    I am trying to install the Catalyst driver. The best I can get is a strange resolution problem and firefox acts all wonkt. The worst I have gotten is low graphics mode in which I just reinstall Ubuntu. I have a HP Pavilion Dv7 laptop. With Radeon 3200 HD. I plan to try again with a fresh install of Ubuntu 12.4.3 as I have heard its the most compatible. This is what I have done: I have tried just the easy way of going to synaptic and installing the drivers that way. the fglrx package (not the fglrx update). And if memory serves I think that boots me into low graphics mode. So, fresh install of Ubuntu and tried again. I have done everything a couple times from this site (http://wiki.cchtml.com/index.php/Ubuntu_Precise_Installation_Guide) following every instruction to a T. That gets me something, such as a lowered fan speed and a much cooler computer, but I also lose most of my resolution. And displays says its the best resolution I can get. I also have a very screwy firefox. Using this method I can see AMD Catalyst Control Center in my dash (two of them really one administrator and one not) but when I try to open it it says no amd driver detected. So again, ubuntu reinstall. I have tried the GUI method from the Legacy driver I got from AMD's site. It runs through smoothly and at the very end after I exit the installer it gives me an error. I have also tried various other methods using terminal, as well as various different drivers (the one from the amd's site and the one suggested in the above link for my graphics card) both to no avail. When I try the method in the link on number 2, and I get the super low res and screwy fire fox. I type in, fglrxinfo ,and get a badrequest error. I have yet to type in fglrxinfo and get anything like what I am supposed to. UPDATE: I am now currently reinstalling Ubuntu 12.4. I tried the above mentioned link - thank you very much!- just to see on the previously failed driver attempt by following the purge commands. And to no avail when typing fglrxinfo I still get the badrequest thing. I will update again after a try with a true fresh install. Thanks again!! UPDATE: Alright everyone. Still no go. I have done everything word per word in the provided tutorial. I have rebooted my computer again to a fucked up resolution and this is what I get when typing fglrxinfo: $ fglrxinfo X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 153 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 12 Current serial number in output stream: 12 I would like to add that when installing this file: fglrx_8.970-0ubuntu1_amd64.deb I got this: Building initial module for 3.8.0-29-generic Error! Bad return status for module build on kernel: 3.8.0-29-generic (x86_64) Consult /var/lib/dkms/fglrx/8.970/build/make.log for more information. update-initramfs: deferring update (trigger activated) Processing triggers for ureadahead ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-29-generic Processing triggers for libc-bin ... ldconfig deferred processing now taking place Any ideas? Anyone? I cant for the life of me figure out what I am doing wrong.

    Read the article

  • Software Center seems to freeze system when installing, syslog has "blocked for more than 120 seconds" errors

    - by nbm
    12.04 (precise) 64-bit Kernel Linux 3.2.0-39 3.6GB memory Intel Core 2 Duo CPU @ 2.40GHz x2 WUBI-installed Ubuntu running on a MacBook Pro 7.1 with OSX running Vista via Boot Camp (hey, I like lots of OS's m'kay?) When installing from Ubuntu software center my system very frequently freezes. This has happened 4 of the last 5 installs. Most recently I was installing the Google Earth .deb from Google's website: clicking the .deb file automatically opens Software Center (otherwise I would have used Synaptic, as I've grown to expect Software Center to freeze my system and I'm rather tired of it.) By "freeze" I mean nothing works: no dash, no launcher, no mouse movement, no alt-tab, can't open terminal (keyboard does not work). Software center does show the "installing" icon but after that it greys out and I can't click anything. REISUB has no effect but a cold power-down and restart is possible. Occasionally, after 5-10 minutes, I'll be able to move the mouse / use the keyboard and run a launcher command or two, although other open apps (Chrome and Software Center) will still be greyed-out/frozen. (I've never waited longer than that - if still unresponsive after 15 minutes I just power down and restart.) Most recently, which is why I am finally posting a question, I waited about 15 minutes and was finally able to open System Monitor while this was going on. Processes tells me that System Monitor is using about 20% of CPU, and nothing else is using much (zeros mostly). In fact I didn't even see Software Center listed? However at this point the system finally partially unfroze, the installation completed, and while I wasn't about to close Software Center I was able to do a system shutdown and fresh restart and I went and took a look at the syslog. In /var/log/syslog I see a lot of ":blocked for more than 120 seconds" messages. Similar to ubuntu hang out with this message :blocked for more than 120 seconds Which has not been answered, and I'm not running a virtual machine. My full syslog with stack traces looks very, very similar to this: Why do tasks on Amazon Xen instance block for over 120 seconds causing server to hang? Note that that question was solved, but that's because the problem was being caused by Amazon and Amazon fixed the bug. I'm not running anything Amazon-related. My syslog does look very similar, however. My question is also similar to this: Troubleshooting server hang But the referenced "duplicate" in that question is about how to kill processes/restart when the system freezes. I know how to kill processes and restart. I want to figure out what is causing the problem so I can try to fix it. I realize that I could just use Synaptic instead of Ubuntu Software Center, but I'd like to try to solve the problem if possible. I'm thinking I should perhaps submit a bug report, but I wanted to first see if anyone else was having any similar problems, and if so what you all did to fix it. I see a number of questions about Software Center freezing and others, including those I linked, about the "blocked for more than 120 seconds" log error, but I didn't see any question that links the two. I did save a copy of the syslog report if anyone wants to see it, but as mentioned it's quite similar to the one posted in the Amazon-related question...and I didn't want to take up even more space unnecessarily as, my apologies - this question has already become extremely verbose!

    Read the article

  • Errors when switching to specific static IP

    - by michaelc
    I had a Fedora box running using my static IP 69.169.136.6, etc, all configured according to what the ISP required. Just recently the hard drive failed (and I should have been keeping better backups) - while it is being recovered I would like to put up a webpage on my Archlinux PC explaining the problem - I presently do not have sufficient access to change the DNS record assigned to the domain. When I change my ip address while my system is running to 69.169.136.6, ifconfig reports the new ip address, but http://whatismyip.com/ does not. When I change it and reboot, I can't ping - the message I recieve is "connect: Network is unreachable" (when given one of google.com 's IP addresses - hostnames give me ping: unknown host xxx). Until I have access to the DNS system, what can I do to make this work? Edit: With new IP address, same problem, IP is now 69.169.136.29. Some commands might be useful: #ping 69.169.136.1 PING 69.169.136.1 (69.169.136.1) 56(84) bytes of data. 64 bytes from 69.169.136.1: icmp_seq=1 ttl=64 time=0.377 ms #ping 69.169.190.211 connect: Network is unreachable #ping 208.72.160.67 connect: Network is unreachable #ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4D:97:23:9B inet addr:69.169.136.29 Bcast:69.169.137.255 Mask:255.255.254.0 inet6 addr: fe80::2e0:4dff:fe97:239b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:132091 errors:0 dropped:0 overruns:0 frame:0 TX packets:17 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9635179 (9.1 Mb) TX bytes:1322 (1.2 Kb) Interrupt:29 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2480 (2.4 Kb) TX bytes:2480 (2.4 Kb) #ip route 69.169.136.0/23 dev eth0 proto kernel scope link src 69.169.136.29 #cat /etc/resolv.conf # Generated by dhcpcd #nameserver 208.67.222.222 #nameserver 208.67.220.220 nameserver 69.169.190.211 nameserver 208.72.160.67 # /etc/resolv.conf.tail can replace this line Update: have new static IP addresses, verified to work in Windows... Relevant portions of /etc/rc.conf below: #Static IP example #eth0="eth0 69.169.136.6 netmask 255.255.254.0 broadcast 69.169.136.1" #eth0="eth0 69.169.136.29 netmask 255.255.254.0 broadcast 69.169.137.255" eth0="eth0 69.169.136.32 netmask 255.255.254.0 broadcast 69.169.137.255" #eth0="dhcp" INTERFACES=(eth0) # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # #gateway="default gw 192.168.0.1" gateway="default gw 69.169.136.1" #gateway="69.169.136.1" ROUTES=(!gateway) #ROUTES=()

    Read the article

  • Partitioning recommendations for a Proxmox VM Server (OpenVZ)

    - by luison
    We are new to virtualization and we are planning to turn our online server into a virualized one, mainly for maintenance, backup and recovery improvements. Initially we would only have one real virtual system with load plus 1-3 copys for testing and recovering and maybe a small centralized syslog virtual machine. We would like, if possible the host machine to include an iptables plus rsync to back up to other machines and some other global security systems. Due to this and the offerings of our hosting supplier we are mainly considering Proxmox for its simplicity (we like the idea of its web admin panel) and as I also understand that the container approach of OpenVMZ systems may fit well resource wise with our setup. The base system comes with debian so we can personalise it to our requirements. Proxmox installations default installs an LVM partition for the VMs. Our doubts are with the fact of what would be the best partition structure for this considering that: we would like to have a mirror of the root partition we could boot from if required (our provider supports booting the system from another partition via control panel) we ideally would like to have a partition that could be shared among the VM systems. We still don't know if this is possible directly with OpenVMZ containers, otherwise we are considering doing this by sharing it via NFS on the host machine. we want to use the backup system available on the proxmox host administrator to programme VMs backups and then rsync it to another machine. With this based on a Linux Raid of aprox (750Gb) we are considering something like: ext3_1/ - (20Gb) ext3_2/bak_root - (20Gb) mostly unmounted, root partition sync LVM_1 /var/lib/vz - (390Gb) partition for virtual images LVM_2 /shared_data - (30Gb) LVM_3 /backups - (300Gb) where all backups would be allocated Our initial tests with Proxmox seem to have issues with snapshots backups like this, perhaps caused by the fact that they can not be done to another LVM partition (error: command 'lvcreate --size 1024M --snapshot --name vzsnap-ns204084.XXX.net-0 /dev/pve/LV' failed with exit code 5) in which case we might have to use a standart ext3 partition (but unsure if we can do this with the 4 primary partition limitations). Does this makes more or less sense? Would it be mad to for example write VMs /var/logs to a NFS mounted partition (on the host system)? Are their any other easier ways to mount host system partitions (or folders) to the VMs?

    Read the article

  • Installing gnome on Linode with Ubuntu 9.10 x64 - remote VNC/RDP

    - by Kieran Benton
    Hi, I'm a self confessed Linux newbie, having lived and worked mostly within the Windows world for most of my life. I'm making the effort to try moving my virtual host from a Windows box to a Linode instance to try and better learn Linux, and one of the uses I occasionally have with my current Windows VPS is to RDP into it and browse the internet. I'm aware that this is probably not best practice (from either performance or security), and most of the time I will be learning from the shell, but I do occasionally need to boot into a GUI. Because of this, I'd like the ability within my Ubuntu installation on Linode to start/stop Windows X and Gnome at will after SSHing in (startx? gdm?), so I've tried: apt-get install ubuntu-desktop Reboot startx But I've got an error that no amount of googling has helped me with so far, which I'm assuming is something to do with the fact the box is headless and X needs some more configuration that is beyond me at the moment: root@local:~# startx hostname: Unknown host xauth: creating new authority file /root/.Xauthority xauth: creating new authority file /root/.Xauthority xauth: (argv):1: bad display name "local.kieranbenton.com:0" in "list" command xauth: (stdin):1: bad display name "local.kieranbenton.com:0" in "add" command X.Org X Server 1.6.4 Release Date: 2009-9-27 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-23-server x86_64 Ubuntu Current Operating System: Linux local.kieranbenton.com 2.6.31.5-x86_64-linode9 #1 SMP Mon Oct 26 19:35:25 UTC 2009 x86_64 Kernel command line: root=/dev/xvda xencons=tty console=tty1 console=hvc0 nosep nodevfs ramdisk_size=32768 ro Build Date: 26 October 2009 05:19:56PM xorg-server 2:1.6.4-2ubuntu4 (buildd@) Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 2 15:50:23 2009 Primary device is not PCI (==) Using default built-in configuration (21 lines) (EE) open /dev/fb0: No such file or directory (EE) No devices detected. Fatal server error: no screens found Please consult the The X.Org Foundation support at http://wiki.x.org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. ddxSigGiveUp: Closing log Can anyone give me any pointers as to how to go from here and get VNC/RDP setup? (RDP would be preferred?). Thanks.

    Read the article

  • Installing gnome on Linode with Ubuntu 9.10 x64 - remote VNC/RDP

    - by Kieran Benton
    Hi, I'm a self confessed Linux newbie, having lived and worked mostly within the Windows world for most of my life. I'm making the effort to try moving my virtual host from a Windows box to a Linode instance to try and better learn Linux, and one of the uses I occasionally have with my current Windows VPS is to RDP into it and browse the internet. I'm aware that this is probably not best practice (from either performance or security), and most of the time I will be learning from the shell, but I do occasionally need to boot into a GUI. Because of this, I'd like the ability within my Ubuntu installation on Linode to start/stop Windows X and Gnome at will after SSHing in (startx? gdm?), so I've tried: apt-get install ubuntu-desktop Reboot startx But I've got an error that no amount of googling has helped me with so far, which I'm assuming is something to do with the fact the box is headless and X needs some more configuration that is beyond me at the moment: root@local:~# startx hostname: Unknown host xauth: creating new authority file /root/.Xauthority xauth: creating new authority file /root/.Xauthority xauth: (argv):1: bad display name "local.kieranbenton.com:0" in "list" command xauth: (stdin):1: bad display name "local.kieranbenton.com:0" in "add" command X.Org X Server 1.6.4 Release Date: 2009-9-27 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-23-server x86_64 Ubuntu Current Operating System: Linux local.kieranbenton.com 2.6.31.5-x86_64-linode9 #1 SMP Mon Oct 26 19:35:25 UTC 2009 x86_64 Kernel command line: root=/dev/xvda xencons=tty console=tty1 console=hvc0 nosep nodevfs ramdisk_size=32768 ro Build Date: 26 October 2009 05:19:56PM xorg-server 2:1.6.4-2ubuntu4 (buildd@) Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 2 15:50:23 2009 Primary device is not PCI (==) Using default built-in configuration (21 lines) (EE) open /dev/fb0: No such file or directory (EE) No devices detected. Fatal server error: no screens found Please consult the The X.Org Foundation support at http://wiki.x.org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. ddxSigGiveUp: Closing log Can anyone give me any pointers as to how to go from here and get VNC/RDP setup? (RDP would be preferred?). Thanks.

    Read the article

  • Best available technology for layered disk cache in linux

    - by SpliFF
    I've just bought a 6-core Phenom with 16G of RAM. I use it primarily for compiling and video encoding (and occassional web/db). I'm finding all activities get disk-bound and I just can't keep all 6 cores fed. I'm buying an SSD raid to sit between the HDD and tmpfs. I want to setup a "layered" filesystem where reads are cached on tmpfs but writes safely go through to the SSD. I want files (or blocks) that haven't been read lately on the SSD to then be written back to a HDD using a compressed FS or block layer. So basically reads: - Check tmpfs - Check SSD - Check HD And writes: - Straight to SSD (for safety), then tmpfs (for speed) And periodically, or when space gets low: - Move least frequently accessed files down one layer. I've seen a few projects of interest. CacheFS, cachefsd, bcache seem pretty close but I'm having trouble determining which are practical. bcache seems a little risky (early adoption), cachefs seems tied to specific network filesystems. There are "union" projects unionfs and aufs that let you mount filesystems over each other (USB device over a DVD usually) but both are distributed as a patch and I get the impression this sort of "transparent" mounting was going to become a kernel feature rather than a FS. I know the kernel has a built-in disk cache but it doesn't seem to work well with compiling. I see a 20x speed improvement when I move my source files to tmpfs. I think it's because the standard buffers are dedicated to a specific process and compiling creates and destroys thousands of processes during a build (just guessing there). It looks like I really want those files precached. I've read tmpfs can use virtual memory. In that case is it practical to create a giant tmpfs with swap on the SSD? I don't need to boot off the resulting layered filesystem. I can load grub, kernel and initrd from elsewhere if needed. So that's the background. The question has several components I guess: Recommended FS and/or block layer for the SSD and compressed HDD. Recommended mkfs parameters (block size, options etc...) Recommended cache/mount technology to bind the layers transparently Required mount parameters Required kernel options / patches, etc..

    Read the article

  • Ubuntu suddenly freezes

    - by tapan
    I've a strange problem with my ubuntu 10.04 installation. Whenever i boot into ubuntu the entire system freezes / hangs soon after (~ 2 mins in). This problem exists on my windows 7 installation too. However if i start World of Warcraft or Warcraft on windows it doesnt hang for the duration i'm playing the game. After i stop playing and exit the game my laptop hangs inside 2 mins. Here is when it gets weirder. If i disconnect the charger, the laptop doesn't hang. However when I start it in ubuntu recovery mode and drop to root shell and use the 'startx' command everything works perfectly. I cannot figure out what the problem is. i have an intel core2duo 2.2ghz processor, intel mobile 965 graphics, 2 GB RAM for more details here is the output of cat /proc/cpuinfo : processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4389.80 clflush size : 64 power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4388.96 clflush size : 64 power management: here is the output of cat /proc/meminfo MemTotal: 2052440 kB MemFree: 55924 kB Buffers: 579352 kB Cached: 821752 kB SwapCached: 704 kB Active: 897124 kB Inactive: 1032256 kB Active(anon): 412140 kB Inactive(anon): 264804 kB Active(file): 484984 kB Inactive(file): 767452 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 1178440 kB HighFree: 6012 kB LowTotal: 874000 kB LowFree: 49912 kB SwapTotal: 995988 kB SwapFree: 986616 kB Dirty: 8928 kB Writeback: 0 kB AnonPages: 527596 kB Mapped: 76536 kB Slab: 39480 kB SReclaimable: 21100 kB SUnreclaim: 18380 kB PageTables: 5672 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2022208 kB Committed_AS: 1856400 kB VmallocTotal: 122880 kB VmallocUsed: 11928 kB VmallocChunk: 104644 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 892928 kB Also the kern.log doesn't show any errors. What I want to know is what might be the problem, how i could test for it and if there are any solutions I could try. Thanks :).

    Read the article

  • cron doesn't execute it's commands

    - by Silvio Keller
    I created an own small server with Debian. Last night i updated it. It created an error while generating the initrd and it didn't boot. Today i booted from another filesystem and did dpkg --configure -a with chroot. I also checked the filesystem. Now everything should be ok. But cron doesn't work:-( It is the same /etc/crontab-File but it doesn't work. I reinstalled cron and tried many things. Is there a way to see cron's log? I only readed about rsyslog, but i have not installed rsyslog, because the server is based on a minimal system (Freeagent Dockstar). Has someone an idea? Best regards Silvio Keller Update There is no file /var/log/syslog and dpkg -l|grep syslog gives me no output, so i think syslog is not installed. It is only a minimal system. cron -l gives: cron: can't lock /var/run/crond.pid, otherpid may be 687: Resource temporarily unavailable So i stopped cron with /etc/init.d/cron stop and executed cron -l again, this gives no output. At this moment i tried to start cron with /etc/init.d/cron start: Starting periodic command scheduler: cron failed! But there's no additional error info... But i see there's now in the background a proccess called cron -l which runs. If i stop it /etc/init.d/cron start works: Starting periodic command scheduler: cron. I used the crontab-file /etc/crontab, this worked for me always. Till i updated my kernel and the initrd it doesn't. The file's content is: SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 6 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) 00 5 * * * root dummy 23 45 * * 7 root dummy 00 * * * * root dummy */1 * * * * root dummy 00 1 * * * root dummy 00 4 * * * root dummy */5 * * * * root dummy #00 */10 * * * root dummy 01 0 * * * root dummy 00 5 * * * root dummy 00 4 * * * root dummy # If i start crontab -e it creates a new file /tmp/crontab.vn87tv/crontab, which is unfortunaly on a tmpfs and which also doesn't work. Thanks & Best regards

    Read the article

  • Ubuntu/Windows suddenly freezes

    - by tapan
    I've a strange problem with my ubuntu 10.04 installation. Whenever i boot into ubuntu the entire system freezes / hangs soon after (~ 2 mins in). This problem exists on my windows 7 installation too. However if i start World of Warcraft or Warcraft on windows it doesnt hang for the duration i'm playing the game. After i stop playing and exit the game my laptop hangs inside 2 mins. Here is when it gets weirder. If i disconnect the charger, the laptop doesn't hang. However when I start it in ubuntu recovery mode and drop to root shell and use the 'startx' command everything works perfectly. I cannot figure out what the problem is. i have an intel core2duo 2.2ghz processor, intel mobile 965 graphics, 2 GB RAM for more details here is the output of cat /proc/cpuinfo : processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4389.80 clflush size : 64 power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4388.96 clflush size : 64 power management: here is the output of cat /proc/meminfo MemTotal: 2052440 kB MemFree: 55924 kB Buffers: 579352 kB Cached: 821752 kB SwapCached: 704 kB Active: 897124 kB Inactive: 1032256 kB Active(anon): 412140 kB Inactive(anon): 264804 kB Active(file): 484984 kB Inactive(file): 767452 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 1178440 kB HighFree: 6012 kB LowTotal: 874000 kB LowFree: 49912 kB SwapTotal: 995988 kB SwapFree: 986616 kB Dirty: 8928 kB Writeback: 0 kB AnonPages: 527596 kB Mapped: 76536 kB Slab: 39480 kB SReclaimable: 21100 kB SUnreclaim: 18380 kB PageTables: 5672 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2022208 kB Committed_AS: 1856400 kB VmallocTotal: 122880 kB VmallocUsed: 11928 kB VmallocChunk: 104644 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 892928 kB Also the kern.log doesn't show any errors. What I want to know is what might be the problem, how i could test for it and if there are any solutions I could try. Thanks :).

    Read the article

  • Problem virtualizing Ubuntu 10.04 32 bit on VirtualBox 3.1 on Windows Vista 64 bit

    - by Adam Siddhi
    Software & Hardware Setup Host System : Windows Vista Home Premium SP1 64 bit Guest : Ubuntu 10.04 (ubuntu-10.04-desktop-i386.iso) 32 bit VM : VirtualBox 3.1.8 Hardware : Intel Core 2 Duo T6400 4GB SDRAM What Happened I followed the tutorial called Installing Ubuntu inside Windows using VirtualBox located here: www.psychocats.net/ubuntu/virtualbox At first I downloaded ubuntu-10.04-desktop-amd64.iso because I figured that it would be a perfect fit with my Vista 64 OS. I was wrong because it turns out the my Intel Core 2 Duo T6400 CPU does not have Intel® Virtualization Technology. So I had to go with the ubuntu-10.04-desktop-i386.iso which is 32 bit. This got me to the point where I could actually create the Ubuntu VM. So I set up the VM in VirtualBox (according to the tutorial I was following) to prepare for the Ubuntu 10.04 virtualization. Please go to my Picassa web album to see the screen shots of my VM settings and Ubuntu boot process so you can see what I experienced (they appear in the order that I experienced them in). www.picasaweb.google.com/rubysiddhi/ProblemVirtualizingUbuntu100432BitOnVirtualBox31OnWindowsVista64# The first 17 images show the VM settings. The last 8 show my attempt at virtualizing Ubuntu 10.04. You can see booting up but ultimately failing. The Specifics The one error message I got was: (process:210): GLib-WARNING **: getpwuid_r(): failed due to unknown user id (0) It appeared on a black screen that sort of looked like a Windows console screen but with out the c:\ or the ability to type. Then this error message got more complex when tons of text appeared in the screen. Pictures 23 - 25 in the album show this text. I should also mention that I found this post in the Ubuntu forums by zonination who seemed to have similar problems to mine even though they had a different set up. The main issue I think zonination and me may be having is the fact that we can not change the color mode to 32 bit while it is booting. I think the 16 bit color mode maybe making Ubuntu fail. Not certain though. Well I hope I explained my problem thoroughly and clearly. Thanks for the tutorial. It got me started but, now I hope to finish this process so I can start developing in Ubuntu. OH by the way if you want to actually see what happened play by play (with some classical in the background) check out the video I made over here: http://www.youtube.com/watch?v=XMbbm5E_0Xw Thanks! Regards, Adam

    Read the article

  • AIX: iscsi volumes disappear after reboot

    - by Dan
    We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet port for iSCSI exclusively.) When we reboot the AIX box, the iSCSI volume doesn't get mounted (which is fine; I've figured out that it fails to mount because AIX tries mounting it's volumes before starting the networking stack.) The problem is, after the server has booted it fails to redetect the iSCSI target as a physical disk. This means the volume group (iscsivg) can't go online. if I run cfgmgr -v to redetect the iscsi volume it successfully detects the iscsi target volume and creates a physical volume reference, but allocates it a different volume ID to what was defined before. eg - rootvg contains hdisk 0 and 1 iscsivg was originally defined with hdisk2 as the physical iSCSI volume. after reboot and running cfgmgr -v, AIX detects physical volumes hdisk0, hdisk11 and hdisk3. As there's no hdisk2, I can't varyon the iscsivg volume group. I can't seem any existing hdisk2 definition in the ODM. I can't easily add or change the definition of the physcial disk in the iscsivg volume group as it won't "varyon". Exporting the volume group deletes it completely, recreating the volume group by "importing" it from the reallocated disk makes it available again, but surely there's a better way? Can I force a specific hdisk drive designation for an iscsi target? How do you bring online iSCSI volumes after a reboot? I assume this "just works" with a dedicated HBA instead of a generic ethernet adapter? By the way, the iSCSI volume works fine once it's mounted; we only have problems getting it working - and only with AIX. The iSCSI array works fine with our Linux and Windows servers; ie the volumes get detected and remounted after boot time without any problems, using generic ethernet adapters. Here's some of the config from the AIX box: defined disks / devices: # lsdev hdisk0 Available 06-08-01-5,0 16 Bit LVD SCSI Disk Drive hdisk1 Available 06-08-01-8,0 16 Bit LVD SCSI Disk Drive hdisk3 Available Other iSCSI Disk Drive iscsi0 Available iSCSI Protocol Device scsi0 Available 06-08-00 PCI-X Dual Channel Ultra320 SCSI Adapter bus scsi1 Available 06-08-01 PCI-X Dual Channel Ultra320 SCSI Adapter bus ses0 Available 06-08-01-15,0 SCSI Enclosure Services Device sisscsia0 Available 06-08 PCI-X Dual Channel Ultra320 SCSI Adapter iscsi target definition in /etc/iscsi/targets: # IBM DS3300 disk array # port 1 on second controller 10.10.xx.xxx 3260 iqn.1992-01.com.lsi:1535.600a0b80005b0a7fxxxxxxxxxxxx physical volumes (after reimporting the volume group) # lspv hdisk0 0003b08a0d4936b6 rootvg active hdisk1 0003b08aaa5cb366 rootvg active hdisk3 0003b08a032d04bb iscsivg active

    Read the article

  • Touch gestures in IE not working without explorer.exe being run once

    - by Michael
    Edit: Rephrasing my question: Upon further troubleshooting, I can conclude that: Touch gestures (dragging, pinch to zoom, touch-and-hold right click) in Internet Explorer start to work when: The system has been running for ~2 minutes. This coincides with the delayed start of services. Explorer.exe is being run, then killed. I assume Explorer.exe starts some services? The services with delayed start are as follows: Security Center Software Protection Windows Defender, Search and Update Windows Font Cache Service Microsoft .NET Framework NGEN v4.0.30319_X64 and X86 I see no connection between these services and touch gestures, but just in case, I manually tried starting these services, but without luck. What else happens delayed after system boot, which also happens when explorer is started? Old question: Details: Internet Explorer 9 and Windows 7 Professional, running on a HP TouchSmart (touch screen PC). It is going to be a kiosk PC (running a custom GUI for displaying websites). Scenario 1: When running Internet Explorer as a normal program in Windows 7, touch functions work perfectly. I can scroll the website by dragging it with my finger, I can pinch zoom and I can touch-and-hold right click. I now change the default shell in Windows to Internet Explorer (ie. IE starts instead of explorer.exe). Internet Explorer of course starts up when logging in. However, touch functions are reduced to basic clicking (no dragging, no pinch zooming, no touch-and-hold right click). Then I manually start explorer.exe, and the touch functions work again! And here is the weird part: When I kill explorer.exe, the touch functions keeps working - even if I close IE and start a new instance. Scenario 2: The exact same, but instead of changing the default shell to Internet Explorer, I change it to my own program, which uses an embedded Internet Explorer ("WebBrowser"). Same thing happens. What I've tried: Autorun programs: When explorer.exe launches, it launches all the autorun programs. There are no relevant programs being run by explorer, but just in case, I have manually started all the autorun programs, so that it is identical (but without explorer.exe) to a normal login. It still does not work (until I launch explorer.exe). Specifically TabTip.exe, TabTip32.exe and wisptis.exe are all running. All services are also started. To sum it up Running explorer.exe once changes something in the touch capabilities of Internet Explorer. It doesn't matter if explorer.exe is running - as long as it has been run once. Does anyone know what causes this behavior? Or how I can circumvent it neatly?

    Read the article

  • Installing drivers for switchable graphics

    - by Anonymous
    I recently bought a laptop that came with Windows 7 64-bit installed. I have some older (16-bit and 32-bit) software that doesn't work with 64-bit Windows, but works just fine with 32-bit. Since I also wanted to get rid of all of the pre-installed spam, I decided to wipe the hard drive and install a fresh copy of Windows 7 32-bit. I can't get the graphics cards working. This laptop uses switchable graphics, an Intel card and a Radeon card. I first tried installing this driver from Intel, which works for the Intel card. Of course, the Radeon card doesn't work with this driver and I need it for some of the newer games I have. I also tried this driver. Windows's device manager will recognize the Radeon card, but it will still use the Intel card. Also, even though that package says it contains the Intel driver, the Intel card still isn't properly recognized by Windows (leaving me with a nasty 800x600 resolution). On top of that, the Catalyst Control Center won't open (saying "The Catalyst Control Center is not supported by the driver version of your enabled graphics adapter") I tried installing HP's driver then installing Intel's driver on top of it. Device manager will then recognize both graphics cards properly. However, the laptop still uses the Intel card. The CCC still won't start (saying the same thing as before) and I can't find any of 'switching' graphics cards. Before formatting, I could right-click the desktop and click "Configure Switchable Graphics" This option hasn't been in the context menu regardless of what driver(s) I've installed. After some research, I found out that this menu entry runs the command "cli.exe Start PowerXpressHybrid" I've tried manually running this command, but I get the same unsupported message from CCC. So, does anyone know how I can get this working? I would like to be able to switch between the Intel and Radeon. But, if there's some way to disable the Intel and use only the Radeon, that would be fine I dual-boot with Linux (framebuffer uses the Intel, haven't even tried getting X set up yet) Here's the output of lspci # lspci -v | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Seymour [AMD Radeon HD 6470M] (prog-if 00 [VGA controller]) The laptop is a HP Pavilion g6t-1d00. HP doesn't support installing anything but Windows 7 64-bit, so calling tech support isn't an option. Thanks for any help UPDATE: I finally got it working. After a fresh install of Windows 7, I installed the HP driver (the one linked above). Then, there's an optional Windows update I installed (don't remember the exact name, but it'll stick out). After that, graphics switching works just like it's supposed to. Moab, thanks anyways for your help

    Read the article

  • vagrant up command very slow on OS X Lion

    - by Andy Hume
    When I run vagrant up to provision a new VM on Lion it takes an extremely long time, during which the entire Mac is very laggy and unresponsive. The output is as follows, the key point being the "notice: Finished catalog run in 754.28 seconds" > vagrant up [default] Importing base box 'lucid64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.1.0 VirtualBox Version: 4.1.6 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- ssh: 22 => 2222 (adapter 1) [default] -- web: 80 => 4567 (adapter 1) [default] Creating shared folders metadata... [default] Running any VM customizations... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant [default] -- v-data: /var/www [default] -- manifests: /tmp/vagrant-puppet/manifests [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: /Stage[main]/Lucid64/Package[apache2]/ensure: ensure changed 'purged' to 'present' [default] [default] notice: /Stage[main]/Lucid64/File[/etc/motd]/ensure: defined content as '{md5}a25e31ba9b8489da9cd5751c447a1741' [default] [default] notice: Finished catalog run in 754.28 seconds [default] [default] err: /File[/var/lib/puppet/rrd]/ensure: change from absent to directory failed: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: change from absent to directory failed: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 2.05 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 1.36 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] >

    Read the article

  • Linux Software RAID recovery

    - by Zoredache
    I am seeing a discrepancy between the output of mdadm --detail and mdadm --examine, and I don't understand why. This output mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Wed Mar 14 18:20:52 2012 Raid Level : raid10 Array Size : 3662760640 (3493.08 GiB 3750.67 GB) Used Dev Size : 1465104256 (1397.23 GiB 1500.27 GB) Raid Devices : 5 Total Devices : 5 Preferred Minor : 2 Persistence : Superblock is persistent Seems to contradict this. (the same for every disk in the array) mdadm --examine /dev/sdc2 /dev/sdc2: Magic : a92b4efc Version : 0.90.00 UUID : 1f54d708:60227dd6:163c2a05:89fa2e07 (local to host) Creation Time : Wed Mar 14 18:20:52 2012 Raid Level : raid10 Used Dev Size : 1465104320 (1397.23 GiB 1500.27 GB) Array Size : 2930208640 (2794.46 GiB 3000.53 GB) Raid Devices : 5 Total Devices : 5 Preferred Minor : 2 The array was created like this. mdadm -v --create /dev/md2 \ --level=raid10 --layout=o2 --raid-devices=5 \ --chunk=64 --metadata=0.90 \ /dev/sdg2 /dev/sdf2 /dev/sde2 /dev/sdd2 /dev/sdc2 Each of the 5 individual drives have partitions like this. Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057754 Device Boot Start End Blocks Id System /dev/sdc1 2048 34815 16384 83 Linux /dev/sdc2 34816 2930243583 1465104384 fd Linux raid autodetect Backstory So the SATA controller failed in a box I provide some support for. The failure was a ugly and so individual drives fell out of the array a little at a time. While there are backups, we the are not really done as frequently as we really need. There is some data that I am trying to recover if I can. I got additional hardware and I was able to access the drives again. The drives appear to be fine, and I can get the array and filesystem active and mounted (using read-only mode). I am able to access some data on the filesystem and have been copying that off, but I am seeing lots of errors when I try to copy the most recent data. When I am trying to access that most recent data I am getting errors like below which makes me think that the array size discrepancy may be the problem. Mar 14 18:26:04 server kernel: [351588.196299] dm-7: rw=0, want=6619839616, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.196309] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.196313] dm-7: rw=0, want=6619839616, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.199260] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.199264] dm-7: rw=0, want=20647626304, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.202446] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.202450] dm-7: rw=0, want=19973212288, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.205516] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.205520] dm-7: rw=0, want=8009695096, limit=6442450944

    Read the article

  • Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

    - by Chris Huang-Leaver
    I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

    Read the article

  • How to create a Windows 7 installation usb media from linux ? (to install Windows 7) - Help need to know better method

    - by Abel Coto
    I have been reading some web pages and posts here and in other forums about how to create a Windows 7 installation Usb media (to install windows 7 using a usb) from linux. I asked in technet about this , and they give me general ideas about how to do it I personally am not very familiar with linux, but basicaly all that you need to do... in whatever way you do it is the following: Format a usb flash drive, either fat32 or ntfs create a partition that is large enough to host the windows installation (give or take 3GB for 64bit, aroudn 2.5gb for 32bit) and mark that partition as active/bootable. Since this can be done with windows, but just as well with a tool like gparted, you should be able to do the same in debian. Once you have created that partition, mount the iso that you download, and copy all files starting from the root, into the root of the usb flash drive. That's all there's to it. There is a method that i found in various places,that is almost the same that the man of technet has said. But,there is a step,that in that method is done,that i don't know if it is really necessary,or not. Not allways dd works.Basically, the missing step was to write a proper boot sector to the usb stick, which can be done from linux with ms-sys. This works with the Win7 retail version. Here is the complete rundown again: Install ms-sys Check what device your usb media is asigned - here we will assume it is /dev/sdb. Delete all partitions, create a new one taking up all the space, set type to NTFS, and set it bootable: *# cfdisk /dev/sdb* Create NTFS filesystem: *# mkfs.ntfs -f /dev/sdb1* Mount iso and usb media: *# mount -o loop win7.iso /mnt/iso # mount /dev/sdb1 /mnt/usb* Copy over all files: *# cp -r /mnt/iso/* /mnt/usb/* Write Windows 7 MBR on usb stick: *# ms-sys -7 /dev/sdb* ...and you're done. Shouldn't the usb work without doing the last step "# ms-sys -7 /dev/sdb" or to make the usb bootable , is a must , not only to mark the partition as bootable ? Would be better use rsync instead of cp -r ? All this steps should be done as root, i suppose , or if not , chmod to 664 and chown the directories where are mounted the usb and the iso, no ? But i suppose that the easier thing is to copy the data as root , and that this will not affect to the data. Has anyone tried this method or some similar like copying the iso with dd ?

    Read the article

  • TPROXY Not working with HAProxy, Ubuntu 14.04

    - by Nyxynyx
    I'm trying to use HAProxy as a fully transparent proxy using TPROXY in Ubuntu 14.04. HAProxy will be setup on the first server with eth1 111.111.250.250 and eth0 10.111.128.134. The single balanced server has eth1 and eth0 as well. eth1 is the public facing network interface while eth0 is for the private network which both servers are in. Problem: I'm able to connect to the balanced server's port 1234 directly (via eth1) but am not able to reach the balanced server via Haproxy port 1234 (which redirects to 1234 via eth0). Am I missing out something in this configuration? On the HAProxy server The current kernel is: Linux extremehash-lb2 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:11:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux The kernel appears to have TPROXY support: # grep TPROXY /boot/config-3.13.0-24-generic CONFIG_NETFILTER_XT_TARGET_TPROXY=m HAProxy was compiled with TPROXY support: haproxy -vv HA-Proxy version 1.5.3 2014/07/25 Copyright 2000-2014 Willy Tarreau <[email protected]> Build options : TARGET = linux26 CPU = x86_64 CC = gcc CFLAGS = -g -fno-strict-aliasing OPTIONS = USE_LINUX_TPROXY=1 USE_LIBCRYPT=1 USE_STATIC_PCRE=1 Default settings : maxconn = 2000, bufsize = 16384, maxrewrite = 8192, maxpollevents = 200 Encrypted password support via crypt(3): yes Built without zlib support (USE_ZLIB not set) Compression algorithms supported : identity Built without OpenSSL support (USE_OPENSSL not set) Built with PCRE version : 8.31 2012-07-06 PCRE library supports JIT : no (USE_PCRE_JIT not set) Built with transparent proxy support using: IP_TRANSPARENT IPV6_TRANSPARENT IP_FREEBIND Available polling systems : epoll : pref=300, test result OK poll : pref=200, test result OK select : pref=150, test result OK Total: 3 (3 usable), will use epoll. In /etc/haproxy/haproxy.cfg, I've configured a port to have the following options: listen test1235 :1234 mode tcp option tcplog balance leastconn source 0.0.0.0 usesrc clientip server balanced1 10.111.163.76:1234 check inter 5s rise 2 fall 4 weight 4 On the balanced server In /etc/networking/interfaces I've set the gateway for eth0 to be the HAProxy box 10.111.128.134 and restarted networking. auto eth0 eth1 iface eth0 inet static address 111.111.250.250 netmask 255.255.224.0 gateway 111.131.224.1 dns-nameservers 8.8.4.4 8.8.8.8 209.244.0.3 iface eth1 inet static address 10.111.163.76 netmask 255.255.0.0 gateway 10.111.128.134 ip route gives: default via 111.111.224.1 dev eth0 10.111.0.0/16 dev eth1 proto kernel scope link src 10.111.163.76 111.111.224.0/19 dev eth0 proto kernel scope link src 111.111.250.250

    Read the article

  • NTPD seems to delete all network interfaces

    - by Aurelin
    We have a couple of virtual interfaces configured on eth0 on a CentOS, and every now and then, they went down seemingly out of the blue. Now after going through the log files, I found out that apparently ntpd deletes all eth0 interfaces, and that dhclient automatically brings eth0 back up. The virtual interfaces, however, stay down which causes several of our websites to be inaccessible. Can someone explain to me why ntpd deletes interfaces? Can / should that be turned off, or can / should I configure dhclient to bring the virtual interfaces back up automatically, too? EDIT// The log files that I should've posted : Nov 12 13:10:28 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x6a825e97) Nov 12 13:10:42 raptor dhclient[20048]: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPOFFER from 96.126.108.78 Nov 12 13:10:42 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPACK from 96.126.108.78 (xid=0x24554092) Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #31 eth0, 50.116.50.97#123, interface stats: received=3255, sent=3256, dropped=0, active_time=1559394 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #32 eth0:0, 50.116.53.56#123, interface stats: received=3, sent=0, dropped=0, active_time=1559391 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #33 eth0:1, 66.175.211.192#123, interface stats: received=2, sent=0, dropped=0, active_time=1559389 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #34 eth0:2, 50.116.53.95#123, interface stats: received=3, sent=0, dropped=0, active_time=1559387 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #35 eth0:3, 97.107.132.32#123, interface stats: received=2, sent=0, dropped=0, active_time=1559385 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #36 eth0:4, 50.116.56.201#123, interface stats: received=2, sent=0, dropped=0, active_time=1559383 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #37 eth0:5, 66.175.212.121#123, interface stats: received=2, sent=0, dropped=0, active_time=1559381 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #38 eth0:6, 66.175.215.137#123, interface stats: received=2, sent=0, dropped=0, active_time=1559379 secs Nov 12 13:10:44 raptor NET[1573]: /sbin/dhclient-script : updated /etc/resolv.conf Nov 12 13:10:44 raptor dhclient[20048]: bound to 50.116.50.97 -- renewal in 32692 seconds. Nov 12 13:10:45 raptor ntpd[2109]: Listening on interface #39 eth0, 50.116.50.97#123 Enabled The eth0 config : DEVICE="eth0" ONBOOT="yes" BOOTPROTO="dhcp" IPV6INIT="no" IPADDR=50.116.50.97 NETMASK=255.255.255.0 GATEWAY=50.116.50.1 And the virtual interfaces (I posted the first one only, they look the same for the most part) : # Configuration for eth0:0 DEVICE=eth0:0 BOOTPROTO=none # This line ensures that the interface will be brought up during boot. ONBOOT=yes # eth0:0 IPADDR=50.116.53.56 NETMASK=255.255.255.0

    Read the article

  • dnsmasq acts as the DHCP server for selected nodes overriding the existing DHCP server on the same LAN?

    - by user183394
    I am trying to set up a small "lab" at home. Like many modern homes, I have a regular DSL service which comes with a 2Wire 3600HGV router, which acts also as a DHCP server. Since I would like to PXE boot a few computers in my "lab" The 2Wire is inflexible to adjustments that I want to do I have used dnsmasq at work so I would like to use dnsmasq as the DHCP server for the few nodes in my "lab" if feasible. In the dnsmasq man page, there is the following: [...] -K, --dhcp-authoritative (IPv4 only) Should be set when dnsmasq is definitely the only DHCP server on a network. It changes the behaviour from strict RFC compliance so that DHCP requests on unknown leases from unknown hosts are not ignored. This allows new hosts to get a lease without a tedious timeout under all circumstances. It also allows dnsmasq to rebuild its lease database without each client needing to reacquire a lease, if the database is lost. [...] As far as I know, the ISC DHCP server can use the following to do what I would like to accomplish: authoritative; [...] subnet 192.168.1.0 netmask 255.255.255.0 { host nb0 { # only give DHCP information to this computer: hardware ethernet e8:9a:8f:17:70:42; fixed-address 192.168.1.10; option subnet-mask 255.255.255.0; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; # Non-essential DHCP options filename "/pxelinux.0"; } [...] But I much prefer dnsmasq's "all-in-one-ness". My question: do I have to couple the -K option with something else? As shown in the example above, the ISC DHCP server requires the mac addresses of managed nodes to be explicitly specified. Does dnsmasq have something similar? FYI, the machine on which I plan to run dnsmasq runs CentOS 6.3 64bit. It has a statically assigned IP address: 192.168.1.3.

    Read the article

  • VMWare-Mount not recognizing virtual disks

    - by user36175
    I have two disks as .vmdk files, and four as .vdi files. I can boot virtual machines on them with Sun xMV VirtualBox, and they work just fine. However, I want to mount them on my local computer so I can read some files off of them without starting a virtual machine. I downloaded the vmware-mount utility, but I get this error, even when mounting .vmdk files, which should be VMWare images... Unable to mount the virtual disk. The disk may be in use by a virtual machine, may not have enough volumes or mounted under another drive letter. If not, verify that the file is a valid virtual disk file. Thinking it's a problem with the utility, I downloaded the SDK and made my own simple program in C to try to mount a disk. It just initializes the API, connects to it, then attempts to open the disk. I get this error, once again claiming it is not a virtual disk: **LOG: DISKLIB-DSCPTR: descriptor above max size: I64u **LOG: DISKLIB-LINK : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-CHAIN : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-LIB : Failed to open 'f:\programming\VMs\windowstrash.vdi' with flags 0x1e (The file specified is not a virtual disk). ** FAILURE ** : The file specified is not a virtual disk The files are clearly virtual disks, though, since I can actually mount and use them with a virtual machine. I tried detaching them from any VMs and trying again, but I got the same results. Any ideas? Maybe the "descriptor above max size" is a hint? Some more info: the .vmdk disks were created on other computers. I just copied them to mine and created new VMs around them, but they work fine. All the .vdi files were created on my machine. Not sure if that affects anything. Update: WinMount can mount the file.. so the problem seems to be with vmware-mount.

    Read the article

< Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343  | Next Page >