Search Results

Search found 8843 results on 354 pages for 'partition master'.

Page 337/354 | < Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >

  • How to delete files and folders that cannot be deleted?

    - by glenneroo
    I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

    Read the article

  • How to use more than 3 virtual disks in Linux using CentOS and XenServer

    - by 010110110101
    I've attached 5 virtual disks to a Virtual Machine in Citrix XenServer. The VM has the xs-tools installed. Initially it said that it couldn't add so many disks. After I installed the xs-tools, it let me add all the disks. But /dev doesn't show all the disks. It shows these: /dev/xvda /dev/xvdb /dev/xvdc /dev/cdrom Perhaps it is bound by the limits of an IDE bus? (3 disks + CD-ROM) If so, how does one change the VM to use SCSI? Edit: According to the documentation: 2.6.3. VM Block Devices In the PV Linux case, block devices are passed through as PV devices. XenServer does not attempt to emulate SCSI or IDE, but instead provides a more suitable interface in the virtual environment in the form of xvd* devices. It is also possible to get an sd* device using the same mechanism, where the PV driver inside the VM takes over the SCSI device namespace. This is not desirable so it is best to use xvd* where possible for PV guests (this is the default for Debian and RHEL). For Windows or other fully virtualized guests, XenServer emulates an IDE bus in the form of an hd* device. When using Windows, installing the Citrix Tools for Virtual Machines installs a special PV driver that works in a similar way to Linux, except in the fully virtualized environment. Still, with 5 virtual disks attached, I don't see the other xvd devices. Edit #2: (attached requested info) Host Machine: XenServer 6.1 Linux version 2.6.32.43-0.4.1.xs1.6.10.777.170770xen (geeko@buildhost) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Wed Apr 17 05:52:03 EDT 2013 Guest Machine: CentOS release 6.4 (Final) Linux version 2.6.32-358.6.2.el6.x86_64 ([email protected]) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Thu May 16 20:59:36 UTC 2013 Output of 'fdisk -l' on Guest Machine: Note, the disk beyond the first 3 attached are not displaying -- there should be 4 100GB disks. (There are a total of 5 disks displayed in XenCenter -- 16GB, 100GB, 100GB, 100GB, 100GB) Disk /dev/xvdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb6c95b9 Device Boot Start End Blocks Id System /dev/xvdb1 1 13054 104856223+ 83 Linux Disk /dev/xvda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e5f41 Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2089 16264192 8e Linux LVM Disk /dev/xvdc: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed249ced Device Boot Start End Blocks Id System /dev/xvdc1 1 13054 104856223+ 83 Linux Disk /dev/mapper/vg_blue-lv_root: 14.6 GB, 14571012096 bytes 255 heads, 63 sectors/track, 1771 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_blue-lv_swap: 2080 MB, 2080374784 bytes 255 heads, 63 sectors/track, 252 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 I see that the Linux versions say SMP. The Guest VM doesn't say "xen" in the name. However, I have already run yum install kernel-xen. Could be a clue?

    Read the article

  • File copying utility like rsync with error handling like ddrescue, for data recovery from a hard drive with bad sectors or hardware failure

    - by purefusion
    I have a hard drive with either bad blocks or sectors that are failing to read due to potential mechanical issues, such as a bad disk head, bad motor, or some other issue that is causing the hard drive to read data excruciatingly slowly and with lots of read errors. I'm seeing an average of 50 KB/sec, with some reads dropping below 10 KB/sec, and frequently it gets stuck on a file or sector altogether, usually for quite a long time—from 2-10 minutes or more (when using rsync, before it times out). Speed seems to vary wildly, and it gets stuck on files a lot, and when it finally gets "unstuck" it only seems to last for a short burst before it gets stuck again. The drive is also very quiet with only an occasional sound of files copying (usually when it gets stuck/unstuck for a brief time, before getting stuck again). Thus, there are none of those evil sounds that are normally associated with HDD death. Someone suggested that the problems sounded like they might be caused by a misaligned disk head, which requires a lot of re-reads before it finally reads data with success. Sounds plausible, but I digress... Anyway, the problem with rsync is that it seems to have no decent error handling support. Obviously, it wasn't meant for use in recovering data from failing hard drives, but all the so-called "data recovery" utilities out there that are meant for such use usually focus on recovery of deleted files or messed up partitions, rather than copying files off dying hard drives. Deleted file recovery is not what I need, obviously, so perhaps you can understand my disappointment in not being able to find what I'm after yet. Naturally, this is where you'd probably say "You should use ddrescue!" Well, that's all fine and dandy, but I've already got most of the data backed up, so I just want to recover certain files. I'm not concerned with trying to recover a full partition block-by-block as ddrescue does. I am only interested in rescuing just specific files and directories. Ideally, what I'd like is some sort of cross between rsync and ddrescue: something that lets me specify source and destination as directories of normal files like rsync (rather than two full partitions as ddrescue requires), with a way to skip files with errors in an initial run, and then allows me to attempt recovery of those files with errors in a later run (with a slightly altered command, of course), perhaps even offering an option to specify the number of retry attempts ...just like how ddrescue works with blocks, only I want a utility that works with specific files/directories like rsync does. So am I daydreaming here, or does something out there exist that can do this? Or, maybe even a way to make rsync or ddrescue work in such a way? I'm really open to whatever solutions might work, so long as they let me choose which files I want to "rescue", and can skip files with errors in the initial run, and try/retry those errors again later. So far I've tried rsync with the following options, but it often gets stuck on a file for longer than the timeout, and ideally I'd just like it to move on to the next file and come back later to the files it gets stuck on. I don't think that's possible though. Anyway, here's what I've been using up till now: rsync -avP --stats --block-size=512 --timeout=600 /path/to/source/* /path/to/destination/

    Read the article

  • Using different SSDs types (not only SATA based) as system drive

    - by Hubert Kario
    Currently I have a Thinkpad X61s and want to make it both a bit faster and a bit more power efficient. For that reason I thought that adding SSD drive would make most sense. Unfortunately, because of financial reasons, buying SSD of over 200GB capacity is out of reach for me (not only it would be worth more than the rest of the laptop, but also I currently have a 500GB drive in it, so even such a drive would be kind of a downgrade for me). During preliminary testing with a cheap Transcend 4GB Class 6 (14MiB/s streaming, 9MiB/s random read) card I experienced boot times to be reduced by half so putting the OS only on it would already would be an improvement. Unfortunately, my system now is about 11GiB in size so anything less than 16GB would be constraining. In this laptop I can connect additional drives on at least 5 different ways: using SATA-ATA converter caddy in the X6 Ultrabase using internal mini PCIe slot using integrated SDHC slot using CardBus (a.k.a PCMCIA or PC Card) slot using USB Thankfully, because I use only Linux on this PC the bootability of them is irrelevant as I can put the /boot partition on internal HDD and / on any of the above mentioned Flash memories (as I already did for the SDHC test). From what I was able to research and from my own experience those options come with rather big downsides or other problems: SATA-ATA caddy It has three downsides: I have to carry the Ultrabse with me at all times (it's not really inconvenient, but those grams do add) and couldn't disconnect it when I want to disconnect the battery It makes the bay unusable for the optical drive and occasional quick access to other hard drives the only caddies I could buy have rather flaky controllers in them so putting my OS on it would hamper its stability Internal mini PCIe slot This would be an ideal solution, if only I could find real PCIe SSDs, not only devices that could talk only SATA or ATA over PCIe mechanical connection (the ones used in Dell Mini or Asus EEE). Theoretically Samsung did release such devices but I couldn't find them in retail anywhere. Integrated SDHC slot It's a nice solution with a single drawback: the fastest 16GB SDHC card on the market can only do around 35MiB/s read and 15MiB/s write while still costing like a normal 40GB SATA SSD that's 10 times faster. Not really cost-effective. CardBus (a.k.a PCMCIA or PC Card) slot Those cards are much faster than the SDHC option (there are ones that can do well over 50MiB/s read in benchmarks) and from what I could find the PCMCIA controller in my laptop does support UDMA so it should be able to deliver comparable speeds. They still cost similarly to SD cards but at least they provide streaming performance comparable to my current HDD. USB That's the worst option. Not only is it limited to 20-30MiB/s by the interface itself the drive would stick out of the laptop so it's a big no no. The question As such I think that going the "CF in a CardBus adapter" route will be the best option. My question is: did anyone try using CF cards in CardBus adapters as system drives with Linux on Thinkpad laptops? Laptops in general? What was the real-world performance? I don't have any CF cards so I can't check how well does it work with suspend/resume, or whatever it's easy to make it work in initramfs (I'm using ArchLinux and SD card was trivial — add 3 modules in single config line and rebuilding initramfs) so any tips/gotchas on this are welcome as well.

    Read the article

  • Samba with Active Directory - shares are readonly, NT_STATUS_MEDIA_WRITE_PROTECTED

    - by froh42
    I've set a samba server that seems to work, all shares are seemingly exported as readonly, however. The machine is called "lx". When I'm on lx I can run the following command: froh@lx:~$ smbclient //lx/export -UAdministrator Enter Administrator's password: Domain=[CUSTOMER] OS=[Unix] Server=[Samba 3.5.4] smb: \> mkdir wrzlbrmpf NT_STATUS_MEDIA_WRITE_PROTECTED making remote directory \wrzlbrmpf smb: \> ls . D 0 Fri Dec 3 19:04:20 2010 .. D 0 Sun Nov 28 01:32:37 2010 zork D 0 Fri Dec 3 18:53:33 2010 bar D 0 Sun Nov 28 23:52:43 2010 ork 1 Fri Dec 3 18:53:02 2010 foo 1 Sun Nov 28 23:52:41 2010 gaga D 0 Fri Dec 3 19:04:20 2010 How can I troubleshoot this? What I did: First I set up a fresh install of Ubuntu 10.10 x64. Second I got kerberos working with the following krb5.conf file: [libdefaults] ticket_lifetime = 24000 clock_skew = 300 default_realm = CUSTOMER.LOCAL [realms] CUSTOMER.LOCAL = { kdc = SB4.customer.local:88 admin_server = SB4.customer.local:464 default_domain = CUSTOMER.LOCAL } [domain_realm] .customer.local = CUSTOMER.LOCAL customer.local = CUSTOMER.LOCAL #[login] # krb4_convert = true # krb4_get_tickets = false I also added winbind to group, passwd and shadow in nsswitch.conf. Seemingly Kerberos works: root@lx:~# net ads testjoin Join is OK root@lx:~# wbinfo -a 'Administrator%MYSECRETPASSWORD' plaintext password authentication succeeded challenge/response password authentication succeeded wbinfo -u and wbinfo -g also spit out a list of users and a list of groups respectiveley. I noted that domain accounts did NOT include a domain and they are in german (as on the SBS 2003 that is the domain server). So I get a "Domänenbenutzer" in wbinfo -u's output not a "CUSTOMER+Domain User" or something similar. I'm not sure anymore what I did to the PAM configuration, but here is what I currently have: root@lx:/etc/pam.d# cat samba @include common-auth @include common-account @include common-session-noninteractive root@lx:/etc/pam.d# grep -ve '^#' common-auth auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login try_first_pass auth requisite pam_deny.so auth required pam_permit.so root@lx:/etc/pam.d# grep -ve '^#' common-account account [success=2 new_authtok_reqd=done default=ignore] pam_unix.so account [success=1 new_authtok_reqd=done default=ignore] pam_winbind.so account requisite pam_deny.so account required pam_permit.so account required pam_krb5.so minimum_uid=1000 root@lx:/etc/pam.d# grep -ve '^#' common-session-noninteractive session [default=1] pam_permit.so session requisite pam_deny.so session required pam_permit.so session optional pam_krb5.so minimum_uid=1000 session required pam_unix.so session optional pam_winbind.so At some point I joined the linux box into the AD domain. After (manually) creating a home directory on the linux box I can log in using the Adminstrator user with the password taken from AD. Now I run samba with the following setup: [global] netbios name = LX realm = CUSTOMER.LOCAL workgroup = CUSTOMER security = ADS encrypt passwords = yes password server = 192.168.20.244 #IP des Domain Controllers os level = 0 socket options = TCP_NODELAY SO_RCVBUF=16384 SO_SNDBUF=16384 idmap uid = 10000-20000 idmap gid = 10000-20000 winbind enum users = Yes winbind enum groups = Yes preferred master = no winbind separator = + dns proxy = no wins proxy = no # client NTLMv2 auth = Yes log level = 2 logfile = /var/log/samba/log.smbd.%U template homedir = /home/%U template shell = /bin/bash [export] path = /mnt/sdc1/export read only = No public = Yes Currently I don't care whether export is exported to everyone or just one user, I want to see somebody WRITING to that directory before I start fiddling with the authentication settings. (Who may access it). As mentioned, accessing the share from smbclient results in this NT_STATUS_MEDIA_WRITE_PROTECTED . Accessing it from windows shows ACLs that look correct (The user may write) - but it does not work, I can only read files not write. The directory to be exported looks like this: root@lx:/etc/pam.d# ls -ld /mnt/ drwxr-xr-x 5 root root 4096 2010-11-28 01:29 /mnt/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/ drwxr-xr-x 4 froh froh 4096 2010-11-28 01:32 /mnt/sdc1/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/export/ drwxrwxrwx+ 5 administrator domänen-admins 4096 2010-12-03 19:04 /mnt/sdc1/export/ root@lx:/etc/pam.d# getfacl /mnt/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/ # owner: root # group: root user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/ # owner: froh # group: froh user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/export/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/export/ # owner: administrator # group: domänen-admins user::rwx group::rwx group:domänen-admins:rwx mask::rwx other::rwx default:user::rwx default:group::rwx default:group:domänen-admins:rwx default:mask::rwx default:other::rwx My, oh my what am I overlooking? What am I to blind to see?

    Read the article

  • Do hard drive enclosures fail/is it the HDD or enclosure?

    - by x0a
    I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

    Read the article

  • Samba with Active Directory - shares are readonly, NT_STATUS_MEDIA_WRITE_PROTECTED

    - by froh42
    I've set a samba server that seems to work, all shares are seemingly exported as readonly, however. The machine is called "lx". When I'm on lx I can run the following command: froh@lx:~$ smbclient //lx/export -UAdministrator Enter Administrator's password: Domain=[CUSTOMER] OS=[Unix] Server=[Samba 3.5.4] smb: \> mkdir wrzlbrmpf NT_STATUS_MEDIA_WRITE_PROTECTED making remote directory \wrzlbrmpf smb: \> ls . D 0 Fri Dec 3 19:04:20 2010 .. D 0 Sun Nov 28 01:32:37 2010 zork D 0 Fri Dec 3 18:53:33 2010 bar D 0 Sun Nov 28 23:52:43 2010 ork 1 Fri Dec 3 18:53:02 2010 foo 1 Sun Nov 28 23:52:41 2010 gaga D 0 Fri Dec 3 19:04:20 2010 How can I troubleshoot this? What I did: First I set up a fresh install of Ubuntu 10.10 x64. Second I got kerberos working with the following krb5.conf file: [libdefaults] ticket_lifetime = 24000 clock_skew = 300 default_realm = CUSTOMER.LOCAL [realms] CUSTOMER.LOCAL = { kdc = SB4.customer.local:88 admin_server = SB4.customer.local:464 default_domain = CUSTOMER.LOCAL } [domain_realm] .customer.local = CUSTOMER.LOCAL customer.local = CUSTOMER.LOCAL #[login] # krb4_convert = true # krb4_get_tickets = false I also added winbind to group, passwd and shadow in nsswitch.conf. Seemingly Kerberos works: root@lx:~# net ads testjoin Join is OK root@lx:~# wbinfo -a 'Administrator%MYSECRETPASSWORD' plaintext password authentication succeeded challenge/response password authentication succeeded wbinfo -u and wbinfo -g also spit out a list of users and a list of groups respectiveley. I noted that domain accounts did NOT include a domain and they are in german (as on the SBS 2003 that is the domain server). So I get a "Domänenbenutzer" in wbinfo -u's output not a "CUSTOMER+Domain User" or something similar. I'm not sure anymore what I did to the PAM configuration, but here is what I currently have: root@lx:/etc/pam.d# cat samba @include common-auth @include common-account @include common-session-noninteractive root@lx:/etc/pam.d# grep -ve '^#' common-auth auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login try_first_pass auth requisite pam_deny.so auth required pam_permit.so root@lx:/etc/pam.d# grep -ve '^#' common-account account [success=2 new_authtok_reqd=done default=ignore] pam_unix.so account [success=1 new_authtok_reqd=done default=ignore] pam_winbind.so account requisite pam_deny.so account required pam_permit.so account required pam_krb5.so minimum_uid=1000 root@lx:/etc/pam.d# grep -ve '^#' common-session-noninteractive session [default=1] pam_permit.so session requisite pam_deny.so session required pam_permit.so session optional pam_krb5.so minimum_uid=1000 session required pam_unix.so session optional pam_winbind.so At some point I joined the linux box into the AD domain. After (manually) creating a home directory on the linux box I can log in using the Adminstrator user with the password taken from AD. Now I run samba with the following setup: [global] netbios name = LX realm = CUSTOMER.LOCAL workgroup = CUSTOMER security = ADS encrypt passwords = yes password server = 192.168.20.244 #IP des Domain Controllers os level = 0 socket options = TCP_NODELAY SO_RCVBUF=16384 SO_SNDBUF=16384 idmap uid = 10000-20000 idmap gid = 10000-20000 winbind enum users = Yes winbind enum groups = Yes preferred master = no winbind separator = + dns proxy = no wins proxy = no # client NTLMv2 auth = Yes log level = 2 logfile = /var/log/samba/log.smbd.%U template homedir = /home/%U template shell = /bin/bash [export] path = /mnt/sdc1/export read only = No public = Yes Currently I don't care whether export is exported to everyone or just one user, I want to see somebody WRITING to that directory before I start fiddling with the authentication settings. (Who may access it). As mentioned, accessing the share from smbclient results in this NT_STATUS_MEDIA_WRITE_PROTECTED . Accessing it from windows shows ACLs that look correct (The user may write) - but it does not work, I can only read files not write. The directory to be exported looks like this: root@lx:/etc/pam.d# ls -ld /mnt/ drwxr-xr-x 5 root root 4096 2010-11-28 01:29 /mnt/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/ drwxr-xr-x 4 froh froh 4096 2010-11-28 01:32 /mnt/sdc1/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/export/ drwxrwxrwx+ 5 administrator domänen-admins 4096 2010-12-03 19:04 /mnt/sdc1/export/ root@lx:/etc/pam.d# getfacl /mnt/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/ # owner: root # group: root user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/ # owner: froh # group: froh user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/export/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/export/ # owner: administrator # group: domänen-admins user::rwx group::rwx group:domänen-admins:rwx mask::rwx other::rwx default:user::rwx default:group::rwx default:group:domänen-admins:rwx default:mask::rwx default:other::rwx My, oh my what am I overlooking? What am I to blind to see?

    Read the article

  • How can I recover an ext4 filesystem corrupted after a fsck?

    - by Regan
    I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

    Read the article

  • why is my centos, nginx, php,mysql server using so much memory

    - by kb2tfa
    i'm not sure where the problem lies. I have: centos 6 mysql php php-fpm wordpress (1 site). this is a dedicated server i'm learning on. as soon as i ran the web url the memory slammed to 125% of a 512k server, i had to upgrade to 1gig, so i'm not sure where the problem lies. I thought by switching to nginx from apache i would have more memory free, but i'm still stuck with the problem. before launching the site with nginx and mysqld running the site was about 5% memory. I reanamed my "my-small.cnf" to my.cnf and put in my /etc folder where the original was, but that seems not to have done it. after looking at my TOP results, i'm starting to think it may be php-fpm eating my memory, but not sure. is php-fpm the preferend way or is there something better to use. I read about possible memory leaks in php-fpm. here is what i have: php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. include=/etc/php-fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Default Value: none pid = /var/run/php-fpm/php-fpm.pid ; Error log file ; Default Value: /var/log/php-fpm.log error_log = /var/log/php-fpm/error.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes ;daemonize = yes ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf end php-fpm.conf

    Read the article

  • I am starting to think that Prevx.com isnt a legit site...but heres my long-winded question

    - by cop1152
    I apologize in advance for the long-winded post. I posted it all because I believe its informative and may be useful. Also, I posted my question at the end. Moments ago I was RDC to a file server in my home (from inside my home). I had opened Firefox and Googled for a manufacturers website. Immediately after clicking the link, Firefox abruptly closed. This seemed odd to me to so I checked the running processes and discovered d.exe, e.exe, and f.exe running. I Googled these processes on a different machine and found them belonging to a key-logger/screen-capturer/trojan called defender.exe, which according to the Prevx lives in c:\documents and settings\user\local settings\temp. (Prevx link http://www.prevx.com/filenames/147352809685142526-X1/DEFENDER32.EXE.html) Simultaneously, an obviously-spoofed Windows Firewall popup appeared on the server asking me to click ‘yes’ to update Windows Firewall. At this time I ended all rogue processes, emptied the temp folder, removed defender.exe from startup, and checked my registry and a few other locations. Before deleting Defender.exe I noted that it was created moments ago, just before Firefox crashed. I believe that I was ‘almost’ infected with this malware. I believe that it needed me to click the phony popup in order to complete infection because it wasn’t allowed to execute processes from the temp folder. After cleaning the machine, I restarted it and have been monitoring it for over an hour. I am debating on whether or not to restore the Windows partition (a separate physical drive from the data) or to just watch it for awhle. I should mention that, because of the specs on this machine, I do not run antivirus software, but I know it well and inspect it regularly. It is a very old Compaq with a 400mhz processer and 512mb of ram. I have a static IP and the server is in the DMZ running an FTP client and some HTTP server software. All files transferred to and stored on this machine are scanned for malware before transferring. Usually the machine only runs 19 processes and performs pretty well for its intended purpose. I posted the story so that you could be aware of a possible new piece of malware and how it acts, but I also have a question or two. First, over the last few months I have noticed that PREVX is listed at the top of most of my Google searches when researching malware, especially for new or obscure malware…and they always want you to purchase something. I don’t think they are one of the top AV companies, so it seems odd that they are always the top Google result. Does anyone have any experience with any of their products? Also, what sites do you rely on for malware researching? Recently, I have found it difficult to find good info because of HijackThis-logs and other deadend info cluttering up my searches. And lastly, besides antivirus, third-party firewall, etc, what settings would you use to lock down a machine to make it more secure in instances where a stubborn admin like myself refuses to run AV? Thanks.

    Read the article

  • dns server bind is not work [closed]

    - by user1742080
    I just installed bind on RHEL 6 and point a domain to that server. but actually when i ping domain it returns error 1214: Here is my named.conf: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { listen-on port 53 { any; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { any; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; zone "mydomain.com"{ type master; file "/var/named/data/named.mydomain.com"; allow-update { none; }; }; AND The content of "/var/named/data/named.mydomain.com": 1 $TTL 38400 2 3 mydomain.com. IN SOA ns1.mydomain.com. milad.yahoo.com. ( 4 2012101201 ; serial number YYMMDDNN 5 28800 ; Refresh 6 7200 ; Retry 7 864000 ; Expire 8 38400 ; Min TTL 9 ) 10 11 mydomain.com. IN A 1.2.3.4 12 www IN A 1.2.3.4 13 ns1.mydomain.com. IN A 1.2.3.4 14 ns2.mydomain.com. IN A 1.2.3.4 15 mydomain.com. IN NS ns1.mydomain.com. 16 mydomain.com. IN NS ns2.mydomain.com. AND i'm sure the named service is running: [root@server ~]# service named status version: 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.3 CPUs found: 8 worker threads: 8 number of zones: 20 debug level: 0 xfers running: 0 xfers deferred: 0 soa queries in progress: 0 query logging is OFF recursive clients: 0/0/1000 tcp clients: 0/100 server is up and running named (pid 26299) is running...

    Read the article

  • linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

    - by devicerandom
    We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

    Read the article

  • Distributed and/or Parallel SSIS processing

    - by Jeff
    Background: Our company hosts SaaS DSS applications, where clients provide us data Daily and/or Weekly, which we process & merge into their existing database. During business hours, load in the servers are pretty minimal as it's mostly users running simple pre-defined queries via the website, or running drill-through reports that mostly hit the SSAS OLAP cube. I manage the IT Operations Team, and so far this has presented an interesting "scaling" issue for us. For our daily-refreshed clients, the server is only "busy" for about 4-6 hrs at night. For our weekly-refresh clients, the server is only "busy" for maybe 8-10 hrs per week! We've done our best to use some simple methods of distributing the load by spreading the daily clients evenly among the servers such that we're not trying to process daily clients back-to-back over night. But long-term this scaling strategy creates two notable issues. First, it's going to consume a pretty immense amount of hardware that sits idle for large periods of time. Second, it takes significant Production Support over-head to basically "schedule" the ETL such that they don't over-lap, and move clients/schedules around if they out-grow the resources on a particular server or allocated time-slot. As the title would imply, one option we've tried is running multiple SSIS packages in parallel, but in most cases this has yielded VERY inconsistent results. The most common failures are DTExec, SQL, and SSAS fighting for physical memory and throwing out-of-memory errors, and ETLs running 3,4,5x longer than expected. So from my practical experience thus far, it seems like running multiple ETL packages on the same hardware isn't a good idea, but I can't be the first person that doesn't want to scale multiple ETLs around manual scheduling, and sequential processing. One option we've considered is virtualizing the servers, which obviously doesn't give you any additional resources, but moves the resource contention onto the hypervisor, which (from my experience) seems to manage simultaneous CPU/RAM/Disk I/O a little more gracefully than letting DTExec, SQL, and SSAS battle it out within Windows. Question to the forum: So my question to the forum is, are we missing something obvious here? Are there tools out there that can help manage running multiple SSIS packages on the same hardware? Would it be more "efficient" in terms of parallel execution if instead of running DTExec, SQL, and SSAS same machine (with every machine running that configuration), we run in pairs of three machines with SSIS running on one machine, SQL on another, and SSAS on a third? Obviously that would only make sense if we could process more than the three ETL we were able to process on the machine independently. Another option we've considered is completely re-architecting our SSIS package to have one "master" package for all clients that attempts to intelligently chose a server based off how "busy" it already is in terms of CPU/Memory/Disk utilization, but that would be a herculean effort, and seems like we're trying to reinvent something that you would think someone would sell (although I haven't had any luck finding it). So in summary, are we missing an obvious solution for this, and does anyone know if any tools (for free or for purchase, doesn't matter) that facilitate running multiple SSIS ETL packages in parallel and on multiple servers? (What I would call a "queue & node based" system, but that's not an official term). Ultimately VMWare's Distributed Resource Scheduler addresses this as you simply run a consistent number of clients per VM that you know will never conflict scheduleing-wise, then leave it up to VMWare to move the VMs around to balance out hardware usage. I'm definitely not against using VMWare to do this, but since we're a 100% Microsoft app stack, it seems like -someone- out there would have solved this problem at the application layer instead of the hypervisor layer by checking on resource utilization at the OS, SQL, SSAS levels. I'm open to ANY discussion on this, and remember no suggestion is too crazy or radical! :-) Right now, VMWare is the only option we've found to get away from "manually" balancing our resources, so any suggestions that leave us on a pure Microsoft stack would be great. Thanks guys, Jeff

    Read the article

  • Bug with asp.net mvc2, collection and ValidationMessageFor ?

    - by Rafael Mueller
    I'm with a really weird bug with asp.net mvc2 (rtm) and ValidationMessageFor. The example below throws a System.Collections.Generic.KeyNotFoundException on Response.Write(Html.ValidationMessageFor(n = n[index].Name)); Any ideas why thats happening? I'm accessing the same dictionary twice before, but it only throws the error on ValidationMessageFor, any thoughts? Here's the code. public class Parent { public IList<Child> Childrens { get; set; } [Required] public string Name { get; set; } } public class Child { [Required] public string Name { get; set; } } The controller public class ParentController : Controller { public ActionResult Create() { var parent = new Parent { Name = "Parent" }; parent.Childrens = new List<Child> { new Child(), new Child(), new Child() }; return View(parent); } } The view (Create.aspx) <%@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<Parent>" %> <%@ Import Namespace="BugAspNetMVC" %> <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> <%Html.EnableClientValidation(); %> <% using (Html.BeginForm()) {%> <%=Html.LabelFor(p => p.Name)%> <%=Html.TextBoxFor(p => p.Name)%> <%=Html.ValidationMessageFor(p => p.Name)%> <%Html.RenderPartial("Childrens", Model.Childrens); %> <%} %> </asp:Content> And the partial view (Childrens.ascx) <%@ Control Language="C#" Inherits="System.Web.Mvc.ViewUserControl<IList<Child>>" %> <%@ Import Namespace="BugAspNetMVC"%> <% for (int i = 0; i < Model.Count; i++) { var index = i; Response.Write(Html.LabelFor(n => n[index].Name)); Response.Write(Html.TextBoxFor(n => n[index].Name)); Response.Write(Html.ValidationMessageFor(n => n[index].Name)); } %>

    Read the article

  • Return Json causes save file dialog in asp.net mvc

    - by Eran
    Hi, I'm integrating jquery fullcalendar into my application. Here is the code i'm using: in index.aspx: <script type="text/javascript"> $(document).ready(function() { $('#calendar').fullCalendar({ events: "/Scheduler/CalendarData" }); }); </script> <div id="calendar"> </div> Here is the code for Scheduler/CalendarData: public ActionResult CalendarData() { IList<CalendarDTO> tasksList = new List<CalendarDTO>(); tasksList.Add(new CalendarDTO { id = 1, title = "Google search", start = ToUnixTimespan(DateTime.Now), end = ToUnixTimespan(DateTime.Now.AddHours(4)), url = "www.google.com" }); tasksList.Add(new CalendarDTO { id = 1, title = "Bing search", start = ToUnixTimespan(DateTime.Now.AddDays(1)), end = ToUnixTimespan(DateTime.Now.AddDays(1).AddHours(4)), url = "www.bing.com" }); return Json(tasksList,JsonRequestBehavior.AllowGet); } private long ToUnixTimespan(DateTime date) { TimeSpan tspan = date.ToUniversalTime().Subtract( new DateTime(1970, 1, 1, 0, 0, 0)); return (long)Math.Truncate(tspan.TotalSeconds); } public ActionResult Index() { return View("Index"); } I also have the following code inside head tag in site.master: <asp:ContentPlaceHolder ID="ContentPlaceHolder1" runat="server" /> <link href="<%= Url.Content("~/Content/jquery-ui-1.7.2.custom.css") %>" rel="stylesheet" type="text/css" /> <link href="~Perspectiva/Content/Site.css" rel="stylesheet" type="text/css" /> <link href="~Perspectiva/Content/fullcalendar.css" rel="stylesheet" type="text/css" /> <script src="~Perspectiva/Scripts/jquery-1.4.2.js" type="text/javascript"></script> <script src="~Perspectiva/Scripts/fullcalendar.js" type="text/javascript"></script> <script src="/Scripts/MicrosoftAjax.debug.js" type="text/javascript"></script> <script src="/Scripts/MicrosoftMvcAjax.debug.js" type="text/javascript"></script> Everything I did was pretty much copied from http://szahariev.blogspot.com/2009/08/jquery-fullcalendar-and-aspnet-mvc.html When navigating to /scheduler/calendardata I get a prompt for saving the json data which contents are exactly what I created in the CalendarData function. What do I need to do in order to render the page correctly? Thanks in advance, Eran

    Read the article

  • How do I work around an HTML Table rendering bug in IE 7?

    - by osmaniac
    I have a table. Some cells span multiple columns. Some cells span multiple rows and columns. But one row (which spans all columns but the rightmost one) creates an artifact. Part of the text in the cell is erroneously repeated left justified on a new row just below the table. I'm baffled. I tried rendering with and without "table-layout: fixed;". Same result. When I originally composed the design using just HTML and CSS, it looked great. But then I worked it into a page and had to add more columns to my master table the right to hold buttons. These buttons are in three groups, each having their own div to control floating and rewrapping when the window gets narrower. One div has another table inside it that groups a single row of buttons. Thus I have table inside div inside td inside outer table. I would prefer a simpler design, but how? This is what I want to have: ................................................................................... . . . . Four rows of data . Three groups of buttons that can reflow . . With several columns . if window gets narrower . . meticulously layed out, . . . That should not resize . . . when window gets narrower . . ................................................................................... . One more row of data spanning the whole screen which stays below the buttons . ................................................................................... What I was doing was putting the three divs with the buttons in the upper right in a single cell that spanned four rows. What other opportunities does CSS offer? The buttons are not allowed to overlap the data on the left or go past the data line below. The original design had the divs with the buttons NOT in a table with the data, but when the window gets narrow, some of the buttons flow such that they go underneath the data, which looks bad. I would post actual HTML, except it is generated by ASP, huge, with lots of CSS styling, and the feature that lets me view the final HTML is not working at the moment. (Built in security in the application.)

    Read the article

  • Removing expired certificates from LDS (new ver of ADAM)

    - by jonthebrewer
    Hi all. This is my situation: We are in the process of replacing a certificate store currently hosted on Sun's iPlanet with Microsoft's Lightweight Directory Services (new version of ADAM with Server 2008). These certificates have been imported into LDS into an application partition (say o=myorg, C=AU). Under this structure I have around 40,000 OU's each one representing a customer under each customers OU are one or more user (iNetOrg) objects (around 60,000 in all). In each user are one or more certificates in the UserCertificate attribute. A combination of in-house written application code and proprietory PKI code reads and publishes these certficates to validate financial transactions. As the LDAP path of the certificates is stored within the customer certificates (and within the application code) and there is zero appetite for changing any of the code, I have had to pick up the iPlanet directory as a whole and dump it in LDS in the same structure. (I will not be using or hosting a Microsoft CA, just implementing an LDAP compliant directory to host these certificates) We have fully tested the application using the data in LDS and everything works fine - here is my dilema and question (finally, phew!) There was no process put in place for removing revoked or expired certificates, consequently the vast majority of the data is completely useless, the system has been running for about 8 years! I have done a quick analysis and I estimate that at least 80% of the data is no longer valid. As I am taking on responsibility for managing the directory I would like to start with a clean directory. Does anyone have any idea how I can cleanup these expired certificates. I am not a highly experienced scripter but have some background in VB. I have been researching the use of CAPICOM and have a feeling this may be able to be used but in exactly what way I am not sure?? I would prefer to write a script that I could specify an expiration date (say any certs that expired prior to 2010) then run against the LDS paritition. This way I can reuse the script periodically to cleanup the directory (as mentioned above - I have no way to adjust the applications that are writing the certs, this is with a third party). Another, less attractive, alternative is to massage the LDIF file (2.7 million lines!) to rip the certs out prior to the import Any help and advice MUCH appreciated. Cheers Jon

    Read the article

  • Best ASP.NET E-Commerce Framework (aspDotNetStoreFront, AbleCommerce, BVCommerce, MediaChase,...)

    - by EfficionDave
    I need a full-featured asp.net E-Commerce solution for a project. It needs to be easily extensible as I need to extend it to integrate with a custom Flash based personalization engine. It should also have a great administrative back-end that handles inventory tracking, report, labels, shipping, ... so that the client can really use it as the basis for their business. I've used quite a few different E-Commerce systems including OSCommerce, Zen Cart, Catalook, and eTailer. While I was impressed with Zen Cart and eTailer, this project is big enough that I want to try a more serious, commercial offering. I'm particularly interested in thoughts on aspdotnetstorefront, BVCommerce, AbleCommerce, and MediaChase. [UPDATE] I've done quite a bit of evaluation since I posted this question and will give some of my findings below: BVCommerce - The price point is nice, the product seems fairly well regarded, and I've heard good things about customizing/extending it, it just doesn't seem like it's going to meet my needs as an Top Tier ECommerce solution. After viewing the tutorial videos, the Admin interface just seems too basic and outdated. aspDotNetStorefront - The integration with DotNetNuke was it's biggest selling point for me but after reading peoples opinions, it's integration seems quite weak. It's sounds like there's a significant learning curve and the architecture just doesn't sound like it's as clean as it should be. AbleCommerce - After a rather thorough evaluation, I have selected AbleCommerce for at least my next project. The Admin interface is beautiful and has a nice list of features. The E-Commerce portion of the user side is very well done, highly skin-able (using Master Pages and a couple other techniques), and the checkout workflow has all the features I need while still being very clean. Source to the API can be bought for $500 but you generally won't need it. There are some 3rd party modules available but there's not currently a large market for these. The biggest glaring weakness of AbleCommerce I've found is their CMS capabilities are very limited and not at all well suited for a non-technical user to make most site content updates. But I have a good solution for that that I plan adapting into AbleCommerce. They will automatically generate a site for you to play with to your heart's content for 30 days. It is defniitely worth checking out.

    Read the article

  • Qt vs .NET - plz no n00bs who don't know wtf they're talking about [closed]

    - by Pirate for Profit
    Man in all these Qt vs. .NET discussions 90% these people don't know WTF they're talking about. Trying to get a real comparison chart going before we embark on a major fucking project. And yes I'm drunk, and yes I use cocaine. Event Handling In Qt the event handling system you just emit signals when something cool happens and then catch them in slots, for instance emit valueChanged(int percent, bool something); and void MyCatcherObj::valueChanged(int p, bool ok){} blocking them and disconnecting them when needed, doing it across threads... once you get the hang of it, it just seems a lot more natural and intuitive than the way the .NET event handling is set up (you know, object sender, CustomEventArgs e). And I'm not just talking about syntax, because in the end the .NET delegate crap is the bomb. I'm also talking about in more than just reflection (because, yes, .NET obviously has much stronger reflection capabilities). I'm talking about in the way the system feels to a human being. Qt wins hands down i m o. Basically, the footprints make more sense and you can visualize the project easier without the clunky event handling system. I wish I could it explain it better. The only thing is, I do love some of the ease of C# compared to C++ and .NET's assembly architecture. That is a big bonus for modular projects, which are a PITA to do in C++. Database Ease of Doing Crap Also what about datasets and database manipulations. I think .net wins here but I'm not sure. Threading/Conccurency How do you guys think of the threading? In .NET, all I've ever done is make like a list of master worker threads with locks. I like QConcurrentFramework, you don't worry about locks or anything, and with the ease of the signal slot system across threads it's nice to get notified about the progress of things. Memory Usage Also what do you think of the overall memory usage comparison. Is the .NET garbage collector pretty on the ball and quick compared to the instantaneous nature of native memory management? Or does it just let programs leak up a storm and lag the computer then clean it up when it's about to really lag? However, I am a n00b who doesn't know what I'm talking about, please school me on the subject.

    Read the article

  • Javascript - find swfobject on included page and call javascript function

    - by Rob
    I’m using the following script on my website to play an mp3 in flash. To instantiate the flash object I use the swfobject framework in a javascript function. When the function is called the player is created and added to the page. The rest of the website is in php and the page calling this script is being included with the php include function. All the other used scripts are in the php 'master'-page var playerMp3 = new SWFObject("scripts/player.swf","myplayer1","0","0","0"); playerMp3.addVariable("file","track.mp3"); playerMp3.addVariable("icons","false"); playerMp3.write("player1"); var player1 = document.getElementById("myplayer1"); var status1 = $("#status1"); $("#play1").click(function(){ player1.sendEvent("play","true"); $("#status1").fadeIn(400); player4.sendEvent("stop","false"); $("#status4").fadeOut(400); player3.sendEvent("stop","false"); $("#status3").fadeOut(400); player2.sendEvent("stop","false"); $("#status2").fadeOut(400); }); $("#stop1").click(function(){ player1.sendEvent("stop","false"); $("#status1").fadeOut(400); }); $(".closeOver").click(function(){ player1.sendEvent("stop","false"); $("#status1").fadeOut(400); }); $(".accordionButton2").click(function(){ player1.sendEvent("stop","false"); $("#status1").fadeOut(400); }); $(".accordionButton3").click(function(){ player1.sendEvent("stop","false"); $("#status1").fadeOut(400); }); $(".turnOffMusic").click(function(){ player1.sendEvent("stop","false"); $("#status1").fadeOut(400); }); }); I have a play-button with the id ‘#play1’ and a stop-button with the id ‘#stop1’ on my page. A div on the same page has the id ‘#status1’ and a little image of a speaker is in the div. When you push the playbutton, the div with the speaker is fading in and when you push the stopbutton, the div with the speaker is fading out, very simple. And it works as I want it to do. But the problem is, when a song is finished, the speaker doesn’t fade out. Is there a simple solution for this? I already tried using the swfobject framework to get the flash player from the page and call the ‘IsPlaying’ on it, but I’m getting the error that ‘swfobject’ can’t be found. All I need is a little push in the right direction or an example showing me how I can correctly get the currently playing audio player (in flash), check if it’s playing and if finished, call a javascript function to led the speaker-image fade-out again. Hope someone here can help me

    Read the article

  • Google Streetview under V3 Code having hiccups and delays

    - by jeffkee
    http://new.brocksmeaton.com/showlisting.php/196/-7210-Arbutus-Place-Whytecliff-West-Vancouver-west-vancouver-real-estate The really odd thing is I had this working yesterday and today it's not working. I'm using jQuery UI to switch the tabs on the location map/street view module. I've recently upgraded the Google Maps code as well as the Google Streetview code to version 3. So when I open it in Firefox, with Firebug on, as soon as I switch to the Streetview tab, the navigation and zoom in out controls show, but nothing shows.. and then when I try to drag the map around, it does not move around, but instead, causes errors in Firebug: "too much recursion". So it causes the whole browser to become buggy, slows down, and the errors happen, and nothing shows on the streetview pane. Most of the map loading code is located in inline Javascript on the page itself. Some of the code is under showlisting.js <script type="text/javascript" src="/js/showlisting.js"></script> <script type="text/javascript"> // Call this function when the page has been loaded function loadmap() { var latlng = new google.maps.LatLng(49.374918567425475, -123.28996885871596); var myOptions = { zoom: 14, center: latlng, mapTypeId: google.maps.MapTypeId.ROADMAP }; var map = new google.maps.Map(document.getElementById('listingmap'), myOptions); var listingicon = '/images/activehouse.png'; var infowindow = new google.maps.InfoWindow(); homemarker = new google.maps.Marker({position: latlng, map: map, icon: listingicon}); google.maps.event.addListener(homemarker, 'click', function() { infowindow.setContent('<div style="height:80px; width:250px; color:#333;"><p>7210 Arbutus Place<br />Whytecliff, West Vancouver</div>') infowindow.open(map,homemarker); }); } function loadpano() { var latlng = new google.maps.LatLng(49.374918567425475, -123.28996885871596); $('#listingpanorama').slideDown(500, function() { var panoramaOptions = { addressControl:false, position: latlng, pov: { heading: 34, pitch: 30, zoom: 1 } }; var panorama = new google.maps.StreetViewPanorama(document.getElementById('listingpanorama'), panoramaOptions); }); return false; } </script> My old one under GOogle API Version 2 is here FYI if you want to take a look at it: http://demo.brixwork.com/master/showlisting.php/63/1701-388-Drake-Street-False-Creek-North-Vancouver-

    Read the article

  • Failed to load viewstate

    - by Jen
    OK have just started getting this error and I'm not sure why. I have a hosting page which has listview and a panel with a usercontrol. The listview loads up records with a linkbutton. You click the link button to edit that particular record - which gets loaded up in the formview (within the usercontrol) which goes to edit mode. After an update occurs in the formview I'm triggering an event which my hosting page is listening for. The hosting page then rebinds the listview to show the updated data. So this all works - but when I then go to click on a different linkbutton I get the below error: Webpage error details User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; InfoPath.3) Timestamp: Fri, 18 Jun 2010 03:15:54 UTC Message: Sys.WebForms.PageRequestManagerServerErrorException: Failed to load viewstate. The control tree into which viewstate is being loaded must match the control tree that was used to save viewstate during the previous request. For example, when adding controls dynamically, the controls added during a post-back must match the type and position of the controls added during the initial request. Line: 4723 Char: 21 Code: 0 URI: http://localhost:1951/AdminWebSite/ScriptResource.axd?d=yfdLw4zYs0bqYqs1arL-htap1ceeKCyW1EXhrhMZy_AqJ36FUpx8b2pzMKL6V7ebYsgJDVm_sZ_ykV1hNtFqgYcJCLLtardHm9-yyA7zC4k1&t=ffffffffec2d9970 Any suggestions as to what is actually wrong?? My event listener does this: protected void RatesEditDate1_EditDateRateUpdated() { if (IsDateRangeValid(txtDisplayFrom, txtDisplayTo)) { PropertyAccommodationRates1.DataBind(); } else { pnlViewAccommodationRates.Visible = false; } divEditRate.Visible = false; } When I click my link button - it should be hitting this but the second time round it errors before hitting the breakpoint: protected void RatesEditDate1_EditDateRateSelected(DateTime theDateTime) { // make sure everything else is invisible pnlAddAccommodation.Visible = false; pnlViewEditAccommodations.Visible = false; RatesEditDate1.TheDateTime = theDateTime; RatesEditDate1.PropertyID = (int)Master.PropertyId; if (!String.IsNullOrEmpty(Accommodations1.SelectedValue)) { RatesEditDate1.AccommodationTypeID = Convert.ToInt32(Accommodations1.SelectedValue); } else { RatesEditDate1.AccommodationTypeID = 0; } divEditRate.Visible = true; } So my listview appears to be being rebound successfully - I can see my changed data.. I just don't know why its complaining about viewstate when I click on the linkbutton. Or is there a better way to update the data in my listview? My listview and formview are bound to objectdata sources (in case that matters) Thanks for the help!

    Read the article

  • "Bad binary signature" in ASP.NET MVC application

    - by David M
    We are getting the error above on some pages of an ASP.NET MVC application when it is deployed to a 64 bit Windows 2008 server box. It works fine on our development machines, though these are 32 bit XP. Just wondered if anyone had encountered this before, and has any suggestions? Details as follows: Bad binary signature. (Exception from HRESULT: 0x80131192) Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Runtime.InteropServices.COMException: Bad binary signature. (Exception from HRESULT: 0x80131192) All projects are set to compile for Any CPU, and are compiled in Release mode. The ASP.NET site is precompiled, and the precompiled build is on a 64 bit Windows 2008 TeamCity build agent. Thanks in advance. EDIT We're still plagued by this. I have looked at all the binaries in the website's bin directory using corflags.exe. None has the 32BIT flag set, and all have a CorFlags value of 9 except for Antlr3.Runtime.dll which has a value of 1. The problem only affects certain pages, and it seems to be those which use FluentValidation (including FluentValidation.Mvc and FluentValidation.xValIntegration assemblies). None of these shows anything out of the ordinary when inspected with corflags.exe, and there are no odd looking dependencies revealed by ildasm. When built locally (32 bit Windows XP) the site deploys and runs fine. When built on the build agents (64 bit Windows 2008 Server) the site displays these errors. The site runs in Integrated Pipeline mode, and is not set to 32 bit. The stack trace is: [COMException (0x80131192): Bad binary signature. (Exception from HRESULT: 0x80131192)] ASP.views_user_newinternal_aspx.__RenderContent2(HtmlTextWriter __w, Control parameterContainer) in e:\TeamCity\buildAgent\work\605ee6b4a5d1dd36\...Admin.Mvc\Views\User\NewInternal.aspx:53 System.Web.UI.Control.RenderChildrenInternal(HtmlTextWriter writer, ICollection children) +115 ASP.views_shared_site_master.__Render__control1(HtmlTextWriter __w, Control parameterContainer) in e:\TeamCity\buildAgent\work\605ee6b4a5d1dd36\...Admin.Mvc\Views\Shared\Site.Master:26 System.Web.UI.Control.RenderChildrenInternal(HtmlTextWriter writer, ICollection children) +115 System.Web.UI.Control.RenderChildrenInternal(HtmlTextWriter writer, ICollection children) +240 System.Web.UI.Page.Render(HtmlTextWriter writer) +38 System.Web.Mvc.ViewPage.Render(HtmlTextWriter writer) +94 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +4240

    Read the article

  • JBoss EJB Bean not bound

    - by portoalet
    Hi, I have the following error Exception in thread "main" javax.naming.NameNotFoundException: CounterBean not bound trying to access an EJB JAR CounterBean.jar deployed on JBoss5 from a client application outside the Application Server. From the Jboss log, it looks like it does not have a global JNDI name? Is this ok? What have I done wrong? JBoss log: 13:50:39,669 INFO [JBossASKernel] Created KernelDeployment for: Counter.jar 13:50:39,672 INFO [JBossASKernel] installing bean: jboss.j2ee:jar=Counter.jar,name=CounterBean,service=EJB3 13:50:39,672 INFO [JBossASKernel] with dependencies: 13:50:39,672 INFO [JBossASKernel] and demands: 13:50:39,673 INFO [JBossASKernel] partition:partitionName=DefaultPartition; Required: Described 13:50:39,673 INFO [JBossASKernel] jboss.ejb:service=EJBTimerService; Required: Described 13:50:39,673 INFO [JBossASKernel] and supplies: 13:50:39,673 INFO [JBossASKernel] jndi:CounterBean 13:50:39,673 INFO [JBossASKernel] Added bean(jboss.j2ee:jar=Counter.jar,name=CounterBean,service=EJB3) to KernelDeployment of: Counte r.jar 13:50:39,712 INFO [SessionSpecContainer] Starting jboss.j2ee:jar=Counter.jar,name=CounterBean,service=EJB3 13:50:39,727 INFO [EJBContainer] STARTED EJB: com.don.CounterBean ejbName: CounterBean 13:50:39,732 INFO [JndiSessionRegistrarBase] Binding the following Entries in Global JNDI: The client code is: public static void main(String[] args) throws NamingException, InterruptedException { InitialContext ctx = new InitialContext(); Counter s = (Counter)ctx.lookup("CounterBean/remote"); for(int i = 0; i < 100; i++ ) { s.printCount(i); Thread.sleep(1000); } } Error message: java -Djava.naming.provider.url=jnp://123.123.123.123:1099 -Djava.naming.factory.initial=org.jnp.interfaces.NamingContextFactory com.don.Client Exception in thread "main" javax.naming.NameNotFoundException: CounterBean not bound at org.jnp.server.NamingServer.getBinding(NamingServer.java:771) at org.jnp.server.NamingServer.getBinding(NamingServer.java:779) at org.jnp.server.NamingServer.getObject(NamingServer.java:785) at org.jnp.server.NamingServer.lookup(NamingServer.java:396) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at sun.rmi.server.UnicastServerRef.dispatch(UnicastServerRef.java:305) at sun.rmi.transport.Transport$1.run(Transport.java:159) at java.security.AccessController.doPrivileged(Native Method) at sun.rmi.transport.Transport.serviceCall(Transport.java:155) at sun.rmi.transport.tcp.TCPTransport.handleMessages(TCPTransport.java:535) at sun.rmi.transport.tcp.TCPTransport$ConnectionHandler.run0(TCPTransport.java:790) at sun.rmi.transport.tcp.TCPTransport$ConnectionHandler.run(TCPTransport.java:649) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:619) at sun.rmi.transport.StreamRemoteCall.exceptionReceivedFromServer(StreamRemoteCall.java:255) at sun.rmi.transport.StreamRemoteCall.executeCall(StreamRemoteCall.java:233) at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:142) at org.jnp.server.NamingServer_Stub.lookup(Unknown Source) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:726) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:686) at javax.naming.InitialContext.lookup(InitialContext.java:392) at com.don.Client.main(Client.java:10)

    Read the article

  • OCR an RSA key fob (security token)

    - by user130582
    I put together a quick WinForm/embedded IE browser control which logs into our company's bank website each morning and scrapes/exports the desired deposit information (the bank is a smallish regional bank). Since we have a few dozen "pseudoaccounts" that draw from the same master account, this actually takes 10-15 minutes to retrieve. Anyway, the only problem is that our business bank account reuires an RSA security token (http://www.rsa.com/node.aspx?id=1156)--if you are not familiar, it is a small device which shows a random 6 digit number every 15(?) seconds, so I have to prompt for this value before starting. This is on top of the website's login based security model, so even if you create a read-only account that can't do anything, you still have to put the RSA number in. We have 5 of these tokens for different people in the company. From our perspective this is nusiance security. I was joking about using a web camera to OCR the digits from the key fob so they didn't have to type it in -- mainly so that the scraping/export would be done before anyone arrives in the morning. Well, they asked if I could really do it. So now I ask you, how hard (how many hours) do you think it would take to OCR these digits reliably from a JPEG image produced by the camera? I already know I can get the JPEG easily. I think you get 3 tries to log in, so it really needs to hit a 99% accuracy rate. I could work on this on my off time, but they don't want me to put more than a few hours into it, so I want to leverage as much existing code as possible. This is a 7-segment display (like an alarm clock) so it's not exactly text that an OCR package would be used to seeing. Also--there is a countdown timer on the side of the display; typically when it is down to 1 bar, you wait until the next number appears and it starts over at 5 bars (like signal strength on your cell phone). So this would need to be OCRd as well but it is not text. Anyway the more I think about it as I type this, the less convinced I am that I can truly get this right, so maybe I should just work on it in my spare time?

    Read the article

< Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >