Search Results

Search found 1013 results on 41 pages for 'christopherous 5000'.

Page 34/41 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

  • i cant ping to my DMZ zone from the local inside PC

    - by Big Denzel
    HI everybody. Can anyone please help me on the following issue. I got a Cisco Asa 5520 configured at my network. I cant ping to my DMZ interface from a local inside network PC. so the only way a ping the DMZ is right from the Cisco ASA firewall, there i can pint to all 3 interfaces, Inside, Outside and DMZ,,,, But no PC from the Inside Network can access the DMZ. Can please any one help? I thank you all in advance Bellow is my Cisco ASA 5520 Firewall show run; ASA-FW# sh run : Saved : ASA Version 7.0(8) ! hostname ASA-FW enable password encrypted passwd encrypted names dns-guard ! interface GigabitEthernet0/0 description "Link-To-GW-Router" nameif outside security-level 0 ip address 41.223.156.109 255.255.255.248 ! interface GigabitEthernet0/1 description "Link-To-Local-LAN" nameif inside security-level 100 ip address 10.1.4.1 255.255.252.0 ! interface GigabitEthernet0/2 description "Link-To-DMZ" nameif dmz security-level 50 ip address 172.16.16.1 255.255.255.0 ! interface GigabitEthernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 description "Local-Management-Interface" no nameif no security-level ip address 192.168.192.1 255.255.255.0 ! ftp mode passive access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.107 eq smtp access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.106 eq www access-list OUT-TO-DMZ extended permit icmp any any log access-list OUT-TO-DMZ extended deny ip any any access-list inside extended permit tcp any any eq pop3 access-list inside extended permit tcp any any eq smtp access-list inside extended permit tcp any any eq ssh access-list inside extended permit tcp any any eq telnet access-list inside extended permit tcp any any eq https access-list inside extended permit udp any any eq domain access-list inside extended permit tcp any any eq domain access-list inside extended permit tcp any any eq www access-list inside extended permit ip any any access-list inside extended permit icmp any any access-list dmz extended permit ip any any access-list dmz extended permit icmp any any access-list cap extended permit ip 10.1.4.0 255.255.252.0 172.16.16.0 255.255.25 5.0 access-list cap extended permit ip 172.16.16.0 255.255.255.0 10.1.4.0 255.255.25 2.0 no pager logging enable logging buffer-size 5000 logging monitor warnings logging trap warnings mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover asdm image disk0:/asdm-508.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (dmz,outside) tcp 41.223.156.106 www 172.16.16.80 www netmask 255.255.255 .255 static (dmz,outside) tcp 41.223.156.107 smtp 172.16.16.25 smtp netmask 255.255.2 55.255 static (inside,dmz) 10.1.0.0 10.1.16.0 netmask 255.255.252.0 access-group OUT-TO-DMZ in interface outside access-group inside in interface inside access-group dmz in interface dmz route outside 0.0.0.0 0.0.0.0 41.223.156.108 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute http server enable http 10.1.4.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside ! ! match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect dns maximum-length 512 inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum: : end ASA-FW# Please Help. Big Denzel

    Read the article

  • Possible to give one connection to each IP?

    - by Alice
    I am having overloading problems. Too many connections, and some IP has more than 20 connection at once. I do this command. netstat -anp |grep 'tcp\|udp' | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n To get total of connection and this is the output: 1 106.3.98.81 1 106.3.98.82 1 108.171.251.2 1 110.85.103.207 1 111.161.30.217 1 113.53.103.55 1 119.235.237.20 1 124.106.19.34 1 157.55.32.166 1 157.55.33.49 1 157.55.34.28 1 175.141.103.239 1 180.76.5.59 1 180.76.5.61 1 188.235.165.216 1 205.213.195.70 1 216.157.222.25 1 218.93.205.100 1 222.77.209.105 1 27.153.148.109 1 27.159.194.242 1 27.159.253.71 1 54.242.122.201 1 61.172.50.99 1 65.55.24.239 1 71.179.78.5 1 74.125.136.27 1 74.125.182.30 1 74.125.182.36 1 79.112.225.39 1 93.190.139.208 2 124.227.191.67 2 157.55.33.84 2 157.55.35.34 2 190.66.3.107 2 203.87.153.38 2 220.161.119.3 2 221.6.15.156 2 27.153.148.116 2 27.159.197.0 2 96.47.224.42 3 202.14.70.1 3 218.6.15.42 3 222.77.218.226 3 222.77.224.187 3 37.59.66.100 3 46.4.181.244 3 87.98.254.192 3 91.207.8.62 4 188.143.233.222 4 218.108.168.166 4 221.12.154.18 4 93.182.157.8 4 94.142.128.183 5 180.246.170.187 5 8.21.6.226 6 178.137.94.87 6 218.93.205.112 7 199.15.234.222 9 9 125.253.97.6 10 178.137.17.196 11 46.118.192.179 12 212.79.14.14 21 72.201.187.135 27 0.0.0.0 Can anyone give me some directions, my server crashed few times this week because of this. Thanks. EDIT: Alright, my error logs says: [Thu Oct 18 12:17:39 2012] [error] could not make child process 4842 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4843 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4855 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4856 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4861 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4869 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4872 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4873 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4874 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4875 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4876 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4880 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4882 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4885 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4897 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4900 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4901 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4906 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4907 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4925 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4926 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4927 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4931 exit, attempting to continue anyway [Thu Oct 18 12:17:40 2012] [notice] caught SIGTERM, shutting down PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20060613+lfs/curl.iso' - /usr/lib/php5/20060613+lfs/curl.iso: cannot open shared object file: No such file or directory in Unknown on line 0 [Thu Oct 18 12:17:45 2012] [notice] Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch configured -- resuming normal operations And I have over thousands of line saying:(each has different process id) [Thu Oct 18 12:17:38 2012] [error] child process 4906 still did not exit, sending a SIGKILL And I also have line saying: [Wed Oct 17 09:44:58 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 50 MaxClients 300 MaxRequestsPerChild 5000 </IfModule>

    Read the article

  • Rails program is not being run on apache + passenger - only directory listing

    - by user909943
    I have successfully installed Phusion passenger + Apache 2 + Rails 3.1 program + git on a linux Debian 6. I ran passenger-install-apache2-module and followed the configuration instructions. I followed also the setup instructions at https://help.ubuntu.com/community/RubyOnRails#Configure%20Apache My program is in /var/www/myrailsproject and runs fine on webrick on my mac. When going to myhomepage.com (example) I only see directory listing. By preventing directory listing and setting Options -Indexes in < Document tag in /etc/apache2/sites-available default or myhomepage.com I get an error on my website: Forbidden You don't have permission to access / on this server. Apache/2.2.19 (Debian) Server at myhomepage.com Port 80 In /etc/apache2/apache.conf I added: ServerName myhomepage.com LoadModule passenger_module /usr/lib/ruby/gems/1.8/gems/passenger-3.0.8/ext/apache2/mod_passenger.so PassengerRoot /usr/lib/ruby/gems/1.8/gems/passenger-3.0.8 PassengerRuby /usr/bin/ruby1.8 In /etc/apache2/sites-available myhomepage.com: < VirtualHost *:80 ServerName myhomepage.com ServerAlias www.myhomepage.com DocumentRoot /var/www/myrailsproject/public ErrorLog /var/www/logs/error.log CustomLog /var/www/logs/access.log combined RailsEnv test RackEnv test RailsBaseURI /mayrailsproject < Directory /var/www/myrailsproject> Options -Indexes FollowSymLinks -MultiViews AllowOverride all Order allow,deny allow from all < /Directory> < Directory /var/www/myrailsproject/public> AllowOverride All Options -Indexes +FollowSymLinks MultiViews Order allow,deny Allow from all < /Directory> RailsSpawnMethod smart PassengerPoolIdleTime 1000 RailsAppSpawnerIdleTime 0 RailsFrameworkSpawnerIdleTime 0 PassengerMaxRequests 5000 PassengerStatThrottleRate 5 < /VirtualHost I think I have tried all possible combinations of values and variables in < Directory (and < Directory /, < Directory /var/www etc.) the dafault looks like: < VirtualHost *:80 ServerName myhomepage.com RailsBaseURI /myrailsproject DocumentRoot /var/www/myrailsproject/public RackEnv test RailsEnv test < Directory /var/www/myrailsproject> Options -Indexes FollowSymLinks -MultiViews AllowOverride None Order deny,allow Deny from all < /Directory> <Directory /root/public/myrailsproject/public> Options -Indexes FollowSymLinks -MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" < Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 < /Directory> < /VirtualHost So I wonder why my rails project is not being run, only directory listing. I do not have any index file in my project, routes.rb routes to root :to = 'static_pages#home' I think all permissions are as they should be. Thanks a lot in advance Regards Íris

    Read the article

  • Windows Service SearchIndexer.exe Crashes on Indexing

    - by Josh Jay
    Relevant Specs: Windows 7 Professional 64-bit SP1 Outlook 2010 Version 14.0.7116.5000 (32-bit) Original Symptom: In outlook, I attempted to search for an email but nothing ever returned and the indicator kept going like it was searching. Attempted Resolutions: I investigated the search options and with some research noticed the Windows Service "Windows Search" (SearchIndexer.exe) was not running. I attempted to start it but I receive this error message: "Windows could not start the Windows Search service on Local Computer. Error 1067: The process terminated unexpectedly." The Event Viewer gives this error entry: Log Name: Application Source: Application Error Date: 6/3/2014 11:02:05 AM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ***REMOVED FOR POST*** Description: Faulting application name: SearchIndexer.exe, version: 7.0.7601.17610, time stamp: 0x4dc0d019 Faulting module name: KERNELBASE.dll, version: 6.1.7601.18229, time stamp: 0x51fb1677 Exception code: 0xc0000005 Fault offset: 0x000000000000940d Faulting process id: 0x6a0 Faulting application start time: 0x01cf7f3cc83757c6 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 06424160-eb30-11e3-9555-843a4b07b336 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2014-06-03T15:02:05.000000000Z" /> <EventRecordID>602923</EventRecordID> <Channel>Application</Channel> <Computer>M6700-12011.ncaa.org</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7601.17610</Data> <Data>4dc0d019</Data> <Data>KERNELBASE.dll</Data> <Data>6.1.7601.18229</Data> <Data>51fb1677</Data> <Data>c0000005</Data> <Data>000000000000940d</Data> <Data>6a0</Data> <Data>01cf7f3cc83757c6</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\system32\KERNELBASE.dll</Data> <Data>06424160-eb30-11e3-9555-843a4b07b336</Data> </EventData> </Event> The regular windows search (from start menu) works fine, and if I reboot the machine the service starts up OK but as soon as it kicks off when I let the machine idle for long enough it crashes (same Event Viewer entry). We also tried the Microsoft Utility to no avail. Has anyone seen this issue before?

    Read the article

  • need assistance with my.cnf - 1500% CPU usage

    - by Alan Long
    I'm running into a few issues with our new database server. It is a HP G8 with 2 INTEL XEON E5-2650 processors and 32GB of ram. This server is dedicated as a MySQL server (5.1.69) for our intranet portal. I have been having issues with this server staying alive - I notice high CPU usage during certain times of day (8% ~ 1500%+) and see very low memory usage (7 ~ 15%) based on using the 'top' command. When the CPU usage passes 1000%, that is when the app usually dies. I'm trying to see what I'm doing wrong with the config file, hopefully one of the experts can chime in and let me know what they think. See below for my.cnf file: [mysqld] default-storage-engine=InnoDB datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock #user=mysql large-pages # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 max_connections=275 tmp_table_size=1G key_buffer_size=384M key_buffer=384M thread_cache_size=1024 long_query_time=5 low_priority_updates=1 max_heap_table_size=1G myisam_sort_buffer_size=8M concurrent_insert=2 table_cache=1024 sort_buffer_size=8M read_buffer_size=5M read_rnd_buffer_size=6M join_buffer_size=16M table_definition_cache=6k open_files_limit=8k slow_query_log #skip-name-resolve # Innodb Settings innodb_buffer_pool_size=18G innodb_thread_concurrency=0 innodb_log_file_size=1G innodb_log_buffer_size=16M innodb_flush_log_at_trx_commit=2 innodb_lock_wait_timeout=50 innodb_file_per_table #innodb_buffer_pool_instances=4 #eliminating double buffering innodb_flush_method = O_DIRECT flush_time=86400 innodb_additional_mem_pool_size=40M #innodb_io_capacity = 5000 #innodb_read_io_threads = 64 #innodb_write_io_threads = 64 # increase until threads_created doesnt grow anymore thread_cache=1024 query_cache_type=1 query_cache_limit=4M query_cache_size=256M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 0 wait_timeout = 1800 connect_timeout = 10 interactive_timeout = 60 [mysqldump] max_allowed_packet=32M [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid log-slow-queries=/var/log/mysql/slow-queries.log long_query_time = 1 log-queries-not-using-indexes we connect to one database with 75 tables, the largest table has 1,150,000 entries and the second largest has 128,036 entries. I have also verified that our PHP queries are optimized as best as possible. Reference - MySQLtuner: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.69-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 420M (Tables: 75) [!!] Total fragmented tables: 75 -------- Security Recommendations ------------------------------------------- [!!] User '[email protected]' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 1h 14m 50s (8M q [1K qps], 705 conn, TX: 6B, RX: 892M) [--] Reads / Writes: 68% / 32% [--] Total buffers: 19.7G global + 35.2M per thread (275 max threads) [!!] Maximum possible memory usage: 29.1G (93% of installed RAM) [OK] Slow queries: 0% (472/8M) [OK] Highest usage of available connections: 66% (183/275) [OK] Key buffer size / total MyISAM indexes: 384.0M/91.0K [OK] Key buffer hit rate: 100.0% (173 cached / 0 reads) [OK] Query cache efficiency: 96.2% (7M cached / 7M selects) [!!] Query cache prunes per day: 553614 [OK] Sorts requiring temporary tables: 0% (3 temp sorts / 1K sorts) [!!] Temporary tables created on disk: 49% (3K on disk / 7K total) [OK] Thread cache hit rate: 74% (183 created / 705 connections) [OK] Table cache hit rate: 97% (231 open / 238 opened) [OK] Open file limit used: 0% (17/8K) [OK] Table locks acquired immediately: 100% (432K immediate / 432K locks) [OK] InnoDB data size / buffer pool: 420.9M/18.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Temporary table size is already large - reduce result set size Reduce your SELECT DISTINCT queries without LIMIT clauses Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 256M) [see warning above] Thanks in advanced for your help!

    Read the article

  • The Partner Perspective from Oracle OpenWorld 2012 - IDC’s Darren Bibby report

    - by Richard Lefebvre
    Below is IDC’s Darren Bibby report on ‘The Partner Perspective from Oracle OpenWorld 2012’. If you missed the 2012 edition, I trust this will give you the willingness to attend next year one! October 26, 2012 I attended my fourth Oracle OpenWorld earlier in October. I always go in with the lens of, "What's in it for partners this year?" Although it's primarily thought of as a customer event - and yes, the bulk of the almost 50,000 attendees are customers - this year's conference was clearly the largest and most important partner event Oracle has ever run. Oracle PartnerNetwork (OPN) Exchange There were more partner attendees than ever, with Oracle citing somewhere around 5000. But the format for partners this year was different. And it was better. Traditionally, Oracle hosts a one-day only Partner Forum on the Sunday before the customer-focused conference begins. This year, the partner content still began on the Sunday, but the worldwide alliances and channels group created an exclusive track throughout the week, just for partners. It featured content specifically targeted towards partners, and was anchored at a nearby hotel. This was a great move for Oracle. The Oracle PartnerNetwork (OPN) team has been in a tricky position for years in that they have enough partners that they need a landmark event in the year, but perhaps not enough to justify a separate, worldwide, large, partner-only event. Coinciding a four day event with Oracle OpenWorld, where anybody who's anybody in the Oracle world attends anyway, is a good solution. The channels leadership team can build from this success for an even better conference next year. It's expected that they will follow a similar strategy. Cloud Announcements for Partners As for the content, it was primarily about the Cloud. For customers, for VARs, for ISVs, for everyone. There were five key Cloud related announcements for partners at the event: Cloud Builder Specialization. This is one of the first broader Specializations that isn't focused on one unique product. It is a designation for partners that offer design and implementation services for private cloud solutions. As such, it will surely be something that nearly every partner will consider, and many will pursue. New Specializations for Cloud Services. Unlike the broad, almost "strategy-level" Specialization above, there are a group of new product-based "merit badges" for many of the new Cloud offerings. Think about a Specialization for the Cloud version of HCM, for instance. Each of these particular specializations will also have Rapid Start implementation methodologies that allow a partner to offer a fixed scope and fixed price bid to customers. Based on the learnings from Oracle Consulting, this means a partner might be able to deliver Cloud HCM in six weeks for a fixed price. In the end, this means more consistent experiences for Oracle customers. Cloud Resale Program. For those partners who achieve one of these Cloud Specializations, it will mean they can actually resell the subscription-based Cloud product. This is important because it has been somewhat of a rarity in the emerging Cloud channel for partners to be able to "take the paper", take the revenue, do the billing, be first line of support etc. This is an important step for Oracle and one the partners will be happy to see. Cloud Referral Program. For those partners who are not as engaged with these specific Cloud products that the Specializations revolve around, there is a new referral program that provides an incentive to recommend Oracle Cloud products. This one-two punch of referral and resale programs is similar in many ways to other vendors who allow more committed partners to resell, while more casual partners can collect fees. It's the model that seems to work. The key to allow a company to resell a subscription product - something that is inherently delivered directly between the vendor and customer - is trust. Achieving a specialization is a good bar to have to meet. Platform as a Service for ISVs. Leveraging some of the overall announcements made by CEO Larry Ellison around a cloud version of its famous database, Oracle also outlined a new ability for ISVs to build cloud services on its new PaaS offering. Details were less available for this announcement, though it's an expected and fitting play for ISVs comfortable with Oracle technology who can now more easily build out cloud applications. There wasn't much talk of an app store to go along with this, but surely it's in the works. Specializations And "The Gap" Coming back to Specializations, Oracle PartnerNetwork (OPN) has 4600 partners worldwide that hold 20,000 Specializations. These are impressive numbers just three years into the new OPN framework. The actual number of Specializations has also grown significantly, up to 111 today and soon around 125 or so with the new Cloud designations. Oracle may need to look at grouping some of these and creating higher level, broader designations that partners could achieve by earning several Specializations in that group. At 125 and growing, this is a lot. On the top of the pyramid, Hitachi Ltd. successfully became the eleventh partner to make it to the highly prestigious Diamond level. Partner programs partially exist in order to recognize capable partners. And it's more than abundantly clear that the Diamond level does this. But I think Oracle has a gap. Specializations show capability in a very specific product area, and all sizes of partners can achieve these. The next level at which to show a level of expertise is the Advanced Specialization. However, this is a massive step up from the regular Specialization. The advanced level requires 50 people to have certification in that particular product area. Most other industry programs have similar higher level statuses, but none are even close to that number. Whereas a customer who sees an Oracle partner with an advanced specialization can be very sure of capability, there is a gap in that there are hundreds or even thousands of 20-50 person solution providers who are top notch in their area of expertise. They will never get to Advanced due to numbers alone. These boutique partners don't really have a way of showing off their talents in the current program. Advanced may not need to be so high to really show that a company has deep expertise. Overall it was a very successful Oracle OpenWorld for Oracle partners of all sizes. There was progress made on making it a bigger and more relevant event. And also on catching up and maybe even leading in some cases with cloud opportunities for partners.

    Read the article

  • Use Those Extra Mouse Buttons to Increase Efficiency

    - by Mark Virtue
    Did you know that the most commonly used mouse actions are clicking a window’s “Close” button (the X in the top-right corner), and clicking the “Back” button (in a browser and various other programs)?  How much time do you spend every day locating the Close button or the Back button with your mouse so that you can click on them?  And what about that mouse you’re using – how many buttons does it have, besides the two main ones?  Most mouses these days have at least four (including the scroll-wheel, which a lot of people don’t realize is also a button as well).  Why not assign those extra buttons to your most common mouse actions, and save yourself a bundle of mousing-around time every day? If your mouse was manufactured by one of the “premium” mouse manufacturers (Microsoft, Logitech, etc), it almost certain came with driver software to allow you to customize your mouse’s controls and take advantage of your mouse’s special features.  Microsoft, for example, provides driver software called IntelliPoint (link below), while Logitech provides SetPoint.  It’s possible that your mouse has some extra buttons but doesn’t come with its own driver software (the author is using a Microsoft Bluetooth Notebook Mouse 5000, which amazingly is not supported by the Microsoft IntelliPoint software!).  If your mouse falls into this category, you can use a marvelous free product called X-Mouse Button Control, from Highresolution Enterprises (link below).  It provides a truly amazing array of mouse configuration options, including assigning actions to buttons on a per-application basis. Once X-Mouse Button Control is downloaded, its setup process is quite straightforward. Once downloaded, you can start the program via Start / Highresolution Enterprises / X-Mouse Button Control.  You will find the program’s icon in the system tray: Right-click on the icon and select Setup from the pop-up menu.  The program’s configuration window appears: It’s extremely unlikely that we will want to change the functionality of our mouse’s two main buttons (left and right), so instead we’ll look at the rest of the options on the right side of the window.  The Middle Button refers to either the third, middle button (found on some old mouses), or the pressing of the wheel itself, as a button (if you didn’t know you could press your wheel like a button, try it out now).  Mouse Button 4 and Mouse Button 5 usually refer to the extra buttons found on the side of the mouse, often near your thumb. So what can we use these extra mouse buttons for?  Well, clearly Close and Back are two obvious candidates.  Each of these can be found by selecting them from the drop-down menu next to each button field: Once the two options are chosen, the window will look something like this: If you’re not interested in choosing Back or Close, you may like to try some of the other options in the list, including: Cut, Copy and Paste Undo Show the Desktop Next/Previous track (for media playback) Open any program Simulate any keystroke or combination of keystrokes ….and many other options.  Explore the drop-down list to see them all. You may decide, for example, that closing the current document (as opposed to the current program) would be a good use for Mouse Button 5.  In other words, we need to simulate the keypress of Ctrl-F4.  Let’s see how we achieve this. First we select Simulated Keystrokes from the drop-down list: The Simulated Keystrokes window opens: The instructions on the page are pretty comprehensive.  If you want to simulate the Ctrl-F4 keystroke, you need to type {CTRL}{F4} into the box: …and then click OK. Assigning Actions to Buttons on a Per-Application Basis One of the most powerful features of X-Mouse Button Control is the ability to assign actions to buttons on a per-application basis.  This means that if we have a particular program open, then our mouse will behave differently – our buttons will do different things. For example, when we have Windows Media Player open, for example, we may wish to have buttons assigned to Play/Pause, Next track and Previous track, as well as changing the volume with the mouse!  This is easy with X-Mouse Button Control.  We start by opening Windows Media Player.  This makes the next step easier.  Then we return to X-Mouse Button Control and add a new “configuration”.  This is done by clicking the Add button: A window opens containing a list of all running programs, including our recently opened Windows Media Player: We select Windows Media Player and click OK.  A new, blank “configuration” is created: We repeat the earlier steps to assign buttons to Play/Pause, Next track and Previous track, and assign scrolling the wheel to alter the volume:   To save all our changes and close the window, we click Apply. Now spend a few minutes thinking of all the applications you use the most, and what are the most common simple tasks you perform in each of those applications.  Those tasks are then perfect candidates for per-application button assignments. There are many more configuration options and capabilities of X-Mouse Button Control – too many to list here.  We encourage you to spend a bit of time exploring the Setup window.  Then, most important of all, don’t forget to use your new mouse buttons!  Get into the habit of using them, and then after a while you’ll start to wonder how you ever tolerated the laborious, tedious, time-consuming process of actually locating each window’s Close button… Download X-Mouse Button Control Highresolution Enterprise Similar Articles Productive Geek Tips Add Specialized Toolbar Buttons to Firefox the Easy WayBoost Your Mouse Pointing Accuracy in WindowsMake Mouse Navigation Faster in WindowsVista Style Popup Previews for Firefox TabsStupid Geek Tricks: Using the Quick Zoom Feature in Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Download Videos from Hulu Pixels invade Manhattan Convert PDF files to ePub to read on your iPad Hide Your Confidential Files Inside Images Get Wildlife Photography Tips at BBC’s PhotoMasterClasses Mashpedia is a Real-time Encyclopedia

    Read the article

  • Web Site Performance and Assembly Versioning – Part 3 Versioning Combined Files Using Mercurial

    - by capgpilk
    Minification and Concatination of JavaScript and CSS Files Versioning Combined Files Using Subversion Versioning Combined Files Using Mercurial – this post I have worked on a project recently where there was a need to version the system (library dll, css and javascript files) by date and Mercurial revision number. This was in the format:- 0.12.524.407 {major}.{year}.{month}{date}.{mercurial revision} Each time there is an internal build using the CI server, it would label the files using this format. When it came time to do a major release, it became v1.{year}.{month}{date}.{mercurial revision}, with each public release having a major version increment. Also as a requirement, each assembly also had to have a new GUID on each build. So like in previous posts, we need to edit the csproj file, and add a couple of Default targets. 1: <?xml version="1.0" encoding="utf-8"?> 2: <Project ToolsVersion="4.0" DefaultTargets="Hg-Revision;AssemblyInfo;Build" 3: xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> 4: <PropertyGroup> Right below the closing tag of the entire project we add our two targets, the first is to get the Mercurial revision number. We first need to import the tasks for MSBuild which can be downloaded from http://msbuildhg.codeplex.com/ 1: <Import Project="..\Tools\MSBuild.Mercurial\MSBuild.Mercurial.Tasks" />   1: <Target Name="Hg-Revision"> 2: <HgVersion LocalPath="$(MSBuildProjectDirectory)" Timeout="5000" 3: LibraryLocation="C:\TortoiseHg\"> 4: <Output TaskParameter="Revision" PropertyName="Revision" /> 5: </HgVersion> 6: <Message Text="Last revision from HG: $(Revision)" /> 7: </Target> With the main Mercurial files being located at c:\TortoiseHg To get a valid GUID we need to escape from the csproj markup and call some c# code which we put in a property group for later reference. 1: <PropertyGroup> 2: <GuidGenFunction> 3: <![CDATA[ 4: public static string ScriptMain() { 5: return System.Guid.NewGuid().ToString().ToUpper(); 6: } 7: ]]> 8: </GuidGenFunction> 9: </PropertyGroup> Now we add in our target for generating the GUID. 1: <Target Name="AssemblyInfo"> 2: <Script Language="C#" Code="$(GuidGenFunction)"> 3: <Output TaskParameter="ReturnValue" PropertyName="NewGuid" /> 4: </Script> 5: <Time Format="yy"> 6: <Output TaskParameter="FormattedTime" PropertyName="year" /> 7: </Time> 8: <Time Format="Mdd"> 9: <Output TaskParameter="FormattedTime" PropertyName="daymonth" /> 10: </Time> 11: <AssemblyInfo CodeLanguage="CS" OutputFile="Properties\AssemblyInfo.cs" 12: AssemblyTitle="name" AssemblyDescription="description" 13: AssemblyCompany="none" AssemblyProduct="product" 14: AssemblyCopyright="Copyright ©" 15: ComVisible="false" CLSCompliant="true" Guid="$(NewGuid)" 16: AssemblyVersion="$(Major).$(year).$(daymonth).$(Revision)" 17: AssemblyFileVersion="$(Major).$(year).$(daymonth).$(Revision)" /> 18: </Target> So this will give use an AssemblyInfo.cs file like this just prior to calling the Build task:- 1: using System; 2: using System.Reflection; 3: using System.Runtime.CompilerServices; 4: using System.Runtime.InteropServices; 5:  6: [assembly: AssemblyTitle("name")] 7: [assembly: AssemblyDescription("description")] 8: [assembly: AssemblyCompany("none")] 9: [assembly: AssemblyProduct("product")] 10: [assembly: AssemblyCopyright("Copyright ©")] 11: [assembly: ComVisible(false)] 12: [assembly: CLSCompliant(true)] 13: [assembly: Guid("9C2C130E-40EF-4A20-B7AC-A23BA4B5F2B7")] 14: [assembly: AssemblyVersion("0.12.524.407")] 15: [assembly: AssemblyFileVersion("0.12.524.407")] Therefore giving us the correct version for the assembly. This can be referenced within your project whether web or Windows based like this:- 1: public static string AppVersion() 2: { 3: return Assembly.GetExecutingAssembly().GetName().Version.ToString(); 4: } As mentioned in previous posts in this series, you can label css and javascript files using this version number and the GetAssemblyIdentity task from the main MSBuild task library build into the .Net framework. 1: <GetAssemblyIdentity AssemblyFiles="bin\TheAssemblyFile.dll"> 2: <Output TaskParameter="Assemblies" ItemName="MyAssemblyIdentities" /> 3: </GetAssemblyIdentity> Then use this to write out the files:- 1: <WriteLinestoFile 2: File="Client\site-style-%(MyAssemblyIdentities.Version).combined.min.css" 3: Lines="@(CSSLinesSite)" Overwrite="true" />

    Read the article

  • Quartz.Net Windows Service Configure Logging

    - by Tarun Arora
    In this blog post I’ll be covering, Logging for Quartz.Net Windows Service 01 – Why doesn’t Quartz.Net Windows Service log by default 02 – Configuring Quartz.Net windows service for logging to eventlog, file, console, etc 03 – Results: Logging in action If you are new to Quartz.Net I would recommend going through, A brief Introduction to Quartz.net Walkthrough of Installing & Testing Quartz.Net as a Windows Service Writing & Scheduling your First HelloWorld job with Quartz.Net   01 – Why doesn’t Quartz.Net Windows Service log by default If you are trying to figure out why… The Quartz.Net windows service isn’t logging The Quartz.Net windows service isn’t writing anything to the event log The Quartz.Net windows service isn’t writing anything to a file How do I configure Quartz.Net windows service to use log4Net How do I change the level of logging for Quartz.Net Look no further, This blog post should help you answer these questions. Quartz.NET uses the Common.Logging framework for all of its logging needs. If you navigate to the directory where Quartz.Net Windows Service is installed (I have the service installed in C:\Program Files (x86)\Quartz.net, you can find out the location by looking at the properties of the service) and open ‘Quartz.Server.exe.config’ you’ll see that the Quartz.Net is already set up for logging to ConsoleAppender and EventLogAppender, but only ‘ConsoleAppender’ is set up as active. So, unless you have the console associated to the Quartz.Net service you won’t be able to see any logging. <log4net> <appender name="ConsoleAppender" type="log4net.Appender.ConsoleAppender"> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t] %-5p %l - %m%n" /> </layout> </appender> <appender name="EventLogAppender" type="log4net.Appender.EventLogAppender"> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t] %-5p %l - %m%n" /> </layout> </appender> <root> <level value="INFO" /> <appender-ref ref="ConsoleAppender" /> <!-- uncomment to enable event log appending --> <!-- <appender-ref ref="EventLogAppender" /> --> </root> </log4net> Problem: In the configuration above Quartz.Net Windows Service only has ConsoleAppender active. So, no logging will be done to EventLog. More over the RollingFileAppender isn’t setup at all. So, Quartz.Net will not log to an application trace log file. 02 – Configuring Quartz.Net windows service for logging to eventlog, file, console, etc Let’s change this behaviour by changing the config file… In the below config file, I have added the RollingFileAppender. This will configure Quartz.Net service to write to a log file. (<appender name="GeneralLog" type="log4net.Appender.RollingFileAppender">) I have specified the location for the log file (<arg key="configFile" value="Trace/application.log.txt"/>) I have enabled the EventLogAppender and RollingFileAppender to be written to by Quartz. Net windows service Changed the default level of logging from ‘Info’ to ‘All’. This means all activity performed by Quartz.Net Windows service will be logged. You might want to tune this back to ‘Debug’ or ‘Info’ later as logging ‘All’ will produce too much data to the logs. (<level value="ALL"/>) Since I have changed the logging level to ‘All’, I have added applicationSetting to remove logging log4Net internal debugging. (<add key="log4net.Internal.Debug" value="false"/>) <?xml version="1.0" encoding="utf-8" ?> <configuration> <configSections> <section name="quartz" type="System.Configuration.NameValueSectionHandler, System, Version=1.0.5000.0,Culture=neutral, PublicKeyToken=b77a5c561934e089" /> <section name="log4net" type="log4net.Config.Log4NetConfigurationSectionHandler, log4net" /> <sectionGroup name="common"> <section name="logging" type="Common.Logging.ConfigurationSectionHandler, Common.Logging" /> </sectionGroup> </configSections> <common> <logging> <factoryAdapter type="Common.Logging.Log4Net.Log4NetLoggerFactoryAdapter, Common.Logging.Log4net"> <arg key="configType" value="INLINE" /> <arg key="configFile" value="Trace/application.log.txt"/> <arg key="level" value="ALL" /> </factoryAdapter> </logging> </common> <appSettings> <add key="log4net.Internal.Debug" value="false"/> </appSettings> <log4net> <appender name="ConsoleAppender" type="log4net.Appender.ConsoleAppender"> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t] %-5p %l - %m%n" /> </layout> </appender> <appender name="EventLogAppender" type="log4net.Appender.EventLogAppender"> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t] %-5p %l - %m%n" /> </layout> </appender> <appender name="GeneralLog" type="log4net.Appender.RollingFileAppender"> <file value="Trace/application.log.txt"/> <appendToFile value="true"/> <maximumFileSize value="1024KB"/> <rollingStyle value="Size"/> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d{HH:mm:ss} [%t] %-5p %c - %m%n"/> </layout> </appender> <root> <level value="ALL" /> <appender-ref ref="ConsoleAppender" /> <appender-ref ref="EventLogAppender" /> <appender-ref ref="GeneralLog"/> </root> </log4net> </configuration>   Note – Please ensure you restart the Quartz.Net Windows service for the config changes to be picked up by the service   03 – Results: Logging in action Once you start the Quartz.Net Windows Service up, the logging should be initiated to write all activities in the Console, EventLog and File… See screen shots below… Figure – Quartz.Net Windows Service logging all activity to the event log Figure – Quartz.Net Windows Service logging all activity to the application log file Where is the output from log4Net ConsoleAppender? As a default behaviour, the console isn't available in windows services, web services, windows forms. The output will simply be dismissed. Unless you are running the process interactively. Which you can do by firing up Quartz.Server.exe –i to see the output   This was fourth in the series of posts on enterprise scheduling using Quartz.net, in the next post I’ll be covering troubleshooting why a scheduled task hasn’t fired on Quartz.net windows service. All Quartz.Net specific blog posts can listed here. Thank you for taking the time out and reading this blog post. If you enjoyed the post, remember to subscribe to http://feeds.feedburner.com/TarunArora. Stay tuned!

    Read the article

  • How to archive data from a table to a local or remote database in SQL 2005 and SQL 2008

    - by simonsabin
    Often you have the need to archive data from a table. This leads to a number of challenges 1. How can you do it without impacting users 2. How can I make it transactionally consistent, i.e. the data I put in the archive is the data I remove from the main table 3. How can I get it to perform well Points 1 is very much tied to point 3. If it doesn't perform well then the delete of data is going to cause lots of locks and thus potentially blocking. For points 1 and 3 refer to my previous posts DELETE-TOP-x-rows-avoiding-a-table-scan and UPDATE-and-DELETE-TOP-and-ORDER-BY---Part2. In essence you need to be removing small chunks of data from your table and you want to do that avoiding a table scan. So that deals with the delete approach but archiving is about inserting that data somewhere else. Well in SQL 2008 they introduced a new feature INSERT over DML (Data Manipulation Language, i.e. SQL statements that change data), or composable DML. The ability to nest DML statements within themselves, so you can past the results of an insert to an update to a merge. I've mentioned this before here SQL-Server-2008---MERGE-and-optimistic-concurrency. This feature is currently limited to being able to consume the results of a DML statement in an INSERT statement. There are many restrictions which you can find here http://msdn.microsoft.com/en-us/library/ms177564.aspx look for the section "Inserting Data Returned From an OUTPUT Clause Into a Table" Even with the restrictions what we can do is consume the OUTPUT from a DELETE and INSERT the results into a table in another database. Note that in BOL it refers to not being able to use a remote table, remote means a table on another SQL instance. To show this working use this SQL to setup two databases foo and fooArchive create database foo go --create the source table fred in database foo select * into foo..fred from sys.objects go create database fooArchive go if object_id('fredarchive',DB_ID('fooArchive')) is null begin     select getdate() ArchiveDate,* into fooArchive..FredArchive from sys.objects where 1=2       end go And then we can use this simple statement to archive the data insert into fooArchive..FredArchive select getdate(),d.* from (delete top (1)         from foo..Fred         output deleted.*) d         go In this statement the delete can be any delete statement you wish so if you are deleting by ids or a range of values then you can do that. Refer to the DELETE-TOP-x-rows-avoiding-a-table-scan post to ensure that your delete is going to perform. The last thing you want to do is to perform 100 deletes each with 5000 records for each of those deletes to do a table scan. For a solution that works for SQL2005 or if you want to archive to a different server then you can use linked servers or SSIS. This example shows how to do it with linked servers. [ONARC-LAP03] is the source server. begin transaction insert into fooArchive..FredArchive select getdate(),d.* from openquery ([ONARC-LAP03],'delete top (1)                     from foo..Fred                     output deleted.*') d commit transaction and to prove the transactions work try, you should get the same number of records before and after. select (select count(1) from foo..Fred) fred        ,(select COUNT(1) from fooArchive..FredArchive ) fredarchive   begin transaction insert into fooArchive..FredArchive select getdate(),d.* from openquery ([ONARC-LAP03],'delete top (1)                     from foo..Fred                     output deleted.*') d rollback transaction   select (select count(1) from foo..Fred) fred        ,(select COUNT(1) from fooArchive..FredArchive ) fredarchive The transactions are very important with this solution. Look what happens when you don't have transactions and an error occurs   select (select count(1) from foo..Fred) fred        ,(select COUNT(1) from fooArchive..FredArchive ) fredarchive   insert into fooArchive..FredArchive select getdate(),d.* from openquery ([ONARC-LAP03],'delete top (1)                     from foo..Fred                     output deleted.*                     raiserror (''Oh doo doo'',15,15)') d                     select (select count(1) from foo..Fred) fred        ,(select COUNT(1) from fooArchive..FredArchive ) fredarchive Before running this think what the result would be. I got it wrong. What seems to happen is that the remote query is executed as a transaction, the error causes that to rollback. However the results have already been sent to the client and so get inserted into the

    Read the article

  • Running Solaris 11 as a control domain on a T2000

    - by jsavit
    There is increased adoption of Oracle Solaris 11, and many customers are deploying it on systems that previously ran Solaris 10. That includes older T1-processor based systems like T1000 and T2000. Even though they are old (from 2005) and don't have the performance of current SPARC servers, they are still functional, stable servers that customers continue to operate. One reason to install Solaris 11 on them is that older machines are attractive for testing OS upgrades before updating current, production systems. Normally this does not present a challenge, because Solaris 11 runs on any T-series or M-series SPARC server. One scenario adds a complication: running Solaris 11 in a control domain on a T1000 or T2000 hosting logical domains. Solaris 11 pre-installed Oracle VM Server for SPARC incompatible with T1 Unlike Solaris 10, Solaris 11 comes with Oracle VM Server for SPARC preinstalled. The ldomsmanager package contains the logical domains manager for Oracle VM Server for SPARC 2.2, which requires a SPARC T2, T2+, T3, or T4 server. It does not work with T1-processor systems, which are only supported by LDoms Manager 1.2 and earlier. The following screenshot shows what happens (bold font) if you try to use Oracle VM Server for SPARC 2.x commands in a Solaris 11 control domain. The commands were issued in a control domain on a T2000 that previously ran Solaris 10. We also display the version of the logical domains manager installed in Solaris 11: root@t2000 psrinfo -vp The physical processor has 4 virtual processors (0-3) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep T SUNW,Sun-Fire-T200 # ldm -V Failed to connect to logical domain manager: Connection refused # pkg info ldomsmanager Name: system/ldoms/ldomsmanager Summary: Logical Domains Manager Description: LDoms Manager - Virtualization for SPARC T-Series Category: System/Virtualization State: Installed Publisher: solaris Version: 2.2.0.0 Build Release: 5.11 Branch: 0.175.0.8.0.3.0 Packaging Date: May 25, 2012 10:20:48 PM Size: 2.86 MB FMRI: pkg://solaris/system/ldoms/[email protected],5.11-0.175.0.8.0.3.0:20120525T222048Z The 2.2 version of the logical domains manager will have to be removed, and 1.2 installed, in order to use this as a control domain. Preparing to change - create a new boot environment Before doing anything else, lets create a new boot environment: # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris NR / 2.14G static 2012-09-25 10:32 # beadm create solaris-1 # beadm activate solaris-1 # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris N / 4.82M static 2012-09-25 10:32 solaris-1 R - 2.14G static 2012-09-29 11:40 # init 0 Normally an init 6 to reboot would have been sufficient, but in the next step I reset the system anyway in order to put the system in factory default mode for a "clean" domain configuration. Preparing to change - reset to factory default There was a leftover domain configuration on the T2000, so I reset it to the factory install state. Since the ldm command is't working yet, it can't be done from the control domain, so I did it by logging onto to the service processor: $ ssh -X admin@t2000-sc Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved. Oracle Advanced Lights Out Manager CMT v1.7.9 Please login: admin Please Enter password: ******** sc> showhost Sun-Fire-T2000 System Firmware 6.7.10 2010/07/14 16:35 Host flash versions: OBP 4.30.4.b 2010/07/09 13:48 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 sc> bootmode config="factory-default" sc> poweroff Are you sure you want to power off the system [y/n]? y SC Alert: SC Request to Power Off Host. SC Alert: Host system has shut down. sc> poweron SC Alert: Host System has Reset At this point I rebooted into the new Solaris 11 boot environment, and Solaris commands showed it was running on the factory default configuration of a single domain owning all 32 CPUs and 32GB of RAM (that's what it looked like in 2005.) # psrinfo -vp The physical processor has 8 cores and 32 virtual processors (0-31) The core has 4 virtual processors (0-3) The core has 4 virtual processors (4-7) The core has 4 virtual processors (8-11) The core has 4 virtual processors (12-15) The core has 4 virtual processors (16-19) The core has 4 virtual processors (20-23) The core has 4 virtual processors (24-27) The core has 4 virtual processors (28-31) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep Mem Memory size: 32640 Megabytes Note that the older processor has 4 virtual CPUs per core, while current processors have 8 per core. Remove ldomsmanager 2.2 and install the 1.2 version The Solaris 11 pkg command is now used to remove the 2.2 version that shipped with Solaris 11: # pkg uninstall ldomsmanager Packages to remove: 1 Create boot environment: No Create backup boot environment: No Services to change: 2 PHASE ACTIONS Removal Phase 130/130 PHASE ITEMS Package State Update Phase 1/1 Package Cache Update Phase 1/1 Image State Update Phase 2/2 Finally, LDoms 1.2 installed via its install script, the same way it was done years ago: # unzip LDoms-1_2-Integration-10.zip # cd LDoms-1_2-Integration-10/Install/ # ./install-ldm Welcome to the LDoms installer. You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. ... ... normal install messages omitted ... The Solaris Security Toolkit applies to Solaris 10, and cannot be used in Solaris 11 (in which several things hardened by the Toolkit are already hardened by default), so answer b in the choice below: You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. Select a security profile from this list: a) Hardened Solaris configuration for LDoms (recommended) b) Standard Solaris configuration c) Your custom-defined Solaris security configuration profile Enter a, b, or c [a]: b ... other install messages omitted for brevity... After install I ensure that the necessary services are enabled, and verify the version of the installed LDoms Manager: # svcs ldmd STATE STIME FMRI online 22:00:36 svc:/ldoms/ldmd:default # svcs vntsd STATE STIME FMRI disabled Aug_19 svc:/ldoms/vntsd:default # ldm -V Logical Domain Manager (v 1.2-debug) Hypervisor control protocol v 1.3 Using Hypervisor MD v 1.1 System PROM: Hypervisor v. 1.7.3. @(#)Hypervisor 1.7.3.c 2010/07/09 15:14\015 OpenBoot v. 4.30.4. @(#)OBP 4.30.4.b 2010/07/09 13:48 Set up control domain and domain services At this point we have a functioning LDoms 1.2 environment that can be configured in the usual fashion. One difference is that LDoms 1.2 behavior had 'delayed configuration mode (as expected) during initial configuration before rebooting the control domain. Another minor difference with a Solaris 11 control domain is that you define virtual switches using the 'vanity name' of the network interface, rather than the hardware driver name as in Solaris 10. # ldm list ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Configuration and resource information is displayed for the configuration under construction; not the current active configuration. The configuration being constructed will only take effect after it is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-c-- SP 32 32640M 3.2% 4d 2h 50m # ldm add-vdiskserver primary-vds0 primary # ldm add-vconscon port-range=5000-5100 primary-vcc0 primary # ldm add-vswitch net-dev=net0 primary-vsw0 primary # ldm set-mau 2 primary # ldm set-vcpu 8 primary # ldm set-memory 4g primary # ldm add-config initial # ldm list-spconfig factory-default initial [current] That's it, really. After reboot, we are ready to install guest domains. Summary - new wine in old bottles This example shows that (new) Solaris 11 can be installed on (old) T2000 servers and used as a control domain. The main activity is to remove the preinstalled Oracle VM Server for 2.2 and install Logical Domains 1.2 - the last version of LDoms to support T1-processor systems. I tested Solaris 10 and Solaris 11 guest domains running on this server and they worked without any surprises. This is a viable way to get further into Solaris 11 adoption, even on older T-series equipment.

    Read the article

  • Library like ENet, but for TCP?

    - by Milo
    I'm not looking to use boost::asio, it is overly complex for my needs. I'm building a game that is cross platform, for desktop, iPhone and Android. I found a library called ENet which is pretty much what I need, but it uses UDP which does not seem to support encryption and a few other things. Given that the game is an event driven card game, TCP seems like the right fit. However, all I have found is WINSOCK / berkley sockets and bost::asio. Here is a sample client server application with ENet: #include <enet/enet.h> #include <stdlib.h> #include <string> #include <iostream> class Host { ENetAddress address; ENetHost * server; ENetHost* client; ENetEvent event; public: Host() :server(NULL) { enet_initialize(); setupServer(); } void setupServer() { if(server) { enet_host_destroy(server); server = NULL; } address.host = ENET_HOST_ANY; /* Bind the server to port 1234. */ address.port = 1721; server = enet_host_create (& address /* the address to bind the server host to */, 32 /* allow up to 32 clients and/or outgoing connections */, 2 /* allow up to 2 channels to be used, 0 and 1 */, 0 /* assume any amount of incoming bandwidth */, 0 /* assume any amount of outgoing bandwidth */); } void daLoop() { while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (server, & event, 5000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_CONNECT: printf ("A new client connected from %x:%u.\n", event.peer -> address.host, event.peer -> address.port); /* Store any relevant client information here. */ event.peer -> data = "Client information"; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("packet", strlen ("packet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("packetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("packet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (server); break; case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; case ENET_EVENT_TYPE_DISCONNECT: printf ("%s disconected.\n", event.peer -> data); /* Reset the peer's client information. */ event.peer -> data = NULL; } } } } ~Host() { if(server) { enet_host_destroy(server); server = NULL; } atexit (enet_deinitialize); } }; class Client { ENetAddress address; ENetEvent event; ENetPeer *peer; ENetHost* client; public: Client() :peer(NULL) { enet_initialize(); setupPeer(); } void setupPeer() { client = enet_host_create (NULL /* create a client host */, 1 /* only allow 1 outgoing connection */, 2 /* allow up 2 channels to be used, 0 and 1 */, 57600 / 8 /* 56K modem with 56 Kbps downstream bandwidth */, 14400 / 8 /* 56K modem with 14 Kbps upstream bandwidth */); if (client == NULL) { fprintf (stderr, "An error occurred while trying to create an ENet client host.\n"); exit (EXIT_FAILURE); } /* Connect to some.server.net:1234. */ enet_address_set_host (& address, "192.168.2.13"); address.port = 1721; /* Initiate the connection, allocating the two channels 0 and 1. */ peer = enet_host_connect (client, & address, 2, 0); if (peer == NULL) { fprintf (stderr, "No available peers for initiating an ENet connection.\n"); exit (EXIT_FAILURE); } /* Wait up to 5 seconds for the connection attempt to succeed. */ if (enet_host_service (client, & event, 20000) > 0 && event.type == ENET_EVENT_TYPE_CONNECT) { std::cout << "Connection to some.server.net:1234 succeeded." << std::endl; } else { /* Either the 5 seconds are up or a disconnect event was */ /* received. Reset the peer in the event the 5 seconds */ /* had run out without any significant event. */ enet_peer_reset (peer); puts ("Connection to some.server.net:1234 failed."); } } void daLoop() { ENetPacket* packet; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("backet", strlen ("backet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("backetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("backet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (client); while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (client, & event, 1000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; } } } } ~Client() { atexit (enet_deinitialize); } }; int main() { std::string a; std::cin >> a; if(a == "host") { Host host; host.daLoop(); } else { Client c; c.daLoop(); } return 0; } I looked at some socket tutorials and they seemed a bit too low level. I just need something that abstracts away the platform (eg, no WINSOCKS) and that has basic ability to keep track of connected clients and send them messages. Thanks

    Read the article

  • Disk Drive not working

    - by user287681
    The CD/DVD drive on my sisters' (I'm helping her shift from Win. XP (now officially deprecated by Microsoft) to Ubuntu) system. Now, it may end up being a failed attempt, all together (Almost the whole last year (when she's been on XP) the disk drive hasn't (not even powering on) been working.), I just want to make sure I've explored every remote possibility. Because I figure, "Huh, now that I've got Ubuntu running, instead of XP, that (just) might make a difference.". I have tried using the sudo lshw command in the terminal, to (seemingly) no avil, but, who knows, you might be able to make something out of it. Here's the output: kyra@kyra-Satellite-P105:~$ sudo lshw [sudo] password for kyra: kyra-satellite-p105 description: Notebook product: Satellite P105 () vendor: TOSHIBA version: PSPA0U-0TN01M serial: 96084354W width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=oem-specific chassis=notebook frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=00900559-F88E-D811-82E0-00163680E992 *-core description: Motherboard product: Satellite P105 vendor: TOSHIBA physical id: 0 version: Not Applicable serial: 1234567890 *-firmware description: BIOS vendor: TOSHIBA physical id: 0 version: V4.70 date: 01/19/20092 size: 92KiB capabilities: isa pci pcmcia pnp upgrade shadowing escd cdboot acpi usb biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM)2 CPU T5 slot: U2E1 size: 1667MHz capacity: 1667MHz width: 64 bits clock: 166MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx x86-64 constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm lahf_lm dtherm cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1 Cache size: 16KiB capacity: 16KiB capabilities: asynchronous internal write-back *-cache:1 description: L2 cache physical id: 6 slot: L2 Cache size: 2MiB capabilities: burst external write-back *-memory description: System Memory physical id: c slot: System board or motherboard size: 2GiB capacity: 3GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: M1 size: 1GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: M2 size: 1GiB width: 64 bits *-pci description: Host bridge product: Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 03 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display:0 description: VGA compatible controller product: Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 03 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0200000-d027ffff ioport:1800(size=8) memory:c0000000-cfffffff memory:d0300000-d033ffff *-display:1 UNCLAIMED description: Display controller product: Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 03 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:d0280000-d02fffff *-multimedia description: Audio device product: NM10/ICH7 Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 02 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:44 memory:d0340000-d0343fff *-pci:0 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:84000000-841fffff ioport:84200000(size=2097152) *-pci:1 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:4000(size=4096) memory:84400000-846fffff ioport:84700000(size=2097152) *-network description: Wireless interface product: PRO/Wireless 3945ABG [Golan] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 02 serial: 00:13:02:d6:d2:35 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl3945 driverversion=3.13.0-29-generic firmware=15.32.2.9 ip=10.110.20.157 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:43 memory:84400000-84400fff *-pci:2 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:5000(size=4096) memory:84900000-84afffff ioport:84b00000(size=2097152) *-usb:0 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:1820(size=32) *-usb:1 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:1840(size=32) *-usb:2 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:1860(size=32) *-usb:3 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #4 vendor: Intel Corporation physical id: 1d.3 bus info: pci@0000:00:1d.3 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:1880(size=32) *-usb:4 description: USB controller product: NM10/ICH7 Family USB2 EHCI Controller vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 02 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:d0544000-d05443ff *-pci:3 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: e2 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list resources: ioport:2000(size=4096) memory:d0000000-d00fffff ioport:80000000(size=67108864) *-pcmcia description: CardBus bridge product: PCIxx12 Cardbus Controller vendor: Texas Instruments physical id: 4 bus info: pci@0000:0a:04.0 version: 00 width: 32 bits clock: 33MHz capabilities: pcmcia bus_master cap_list configuration: driver=yenta_cardbus latency=176 maxlatency=5 mingnt=192 resources: irq:17 memory:d0004000-d0004fff ioport:2400(size=256) ioport:2800(size=256) memory:80000000-83ffffff memory:88000000-8bffffff *-firewire description: FireWire (IEEE 1394) product: PCIxx12 OHCI Compliant IEEE 1394 Host Controller vendor: Texas Instruments physical id: 4.1 bus info: pci@0000:0a:04.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm ohci bus_master cap_list configuration: driver=firewire_ohci latency=64 maxlatency=4 mingnt=3 resources: irq:17 memory:d0007000-d00077ff memory:d0000000-d0003fff *-storage description: Mass storage controller product: 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) vendor: Texas Instruments physical id: 4.2 bus info: pci@0000:0a:04.2 version: 00 width: 32 bits clock: 33MHz capabilities: storage pm bus_master cap_list configuration: driver=tifm_7xx1 latency=64 maxlatency=4 mingnt=7 resources: irq:17 memory:d0005000-d0005fff *-generic description: SD Host controller product: PCIxx12 SDA Standard Compliant SD Host Controller vendor: Texas Instruments physical id: 4.3 bus info: pci@0000:0a:04.3 version: 00 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=sdhci-pci latency=64 maxlatency=4 mingnt=7 resources: irq:17 memory:d0007800-d00078ff *-network description: Ethernet interface product: PRO/100 VE Network Connection vendor: Intel Corporation physical id: 8 bus info: pci@0000:0a:08.0 logical name: eth0 version: 02 serial: 00:16:36:80:e9:92 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half latency=64 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10Mbit/s resources: irq:20 memory:d0006000-d0006fff ioport:2000(size=64) *-isa description: ISA bridge product: 82801GBM (ICH7-M) LPC Interface Bridge vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 02 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide description: IDE interface product: 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 02 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:18b0(size=16) *-serial UNCLAIMED description: SMBus product: NM10/ICH7 Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 02 width: 32 bits clock: 33MHz configuration: latency=0 resources: ioport:18c0(size=32) *-scsi physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: ST9250421AS vendor: Seagate physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: SD13 serial: 5TH0B2HB size: 232GiB (250GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=000d7fd5 *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: 13bb4bdd-8cc9-40e2-a490-dbe436c2a02d size: 230GiB capacity: 230GiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2014-06-01 17:37:01 filesystem=ext4 lastmountpoint=/ modified=2014-06-01 21:15:21 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2014-06-01 21:15:21 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 2037MiB capacity: 2037MiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 2037MiB capabilities: nofs *-remoteaccess UNCLAIMED vendor: Intel physical id: 1 capabilities: inbound kyra@kyra-Satellite-P105:~$

    Read the article

  • Unable to boot Ubuntu 13.10 (nVidia GTX 770m and Intel HD 4600)

    - by Raziel Gonzalez
    Ever since I bought this laptop I've been trying to install Ubuntu on it. It came with W8 preinstalled. Up to this point, I've been able to boot in UEFI mode with a black screen. I can tell it's trying to use the nVidia card (there's a led on the computer, depending on the color you can tell which GPU is using) and if I press crtl+alt+F1 I can go to console mode. Taking this advantage I tried to install bumblebee and after a successful install the led that indicates which GPU is being used change, indicating that it switched to the Intel HD 4600 graphics. After the installation I tried to initiate the graphic interface (startx) with no success. Xorg.0.log shows the error: [ 3706.779] X.Org X Server 1.14.3 Release Date: 2013-09-12 [ 3706.782] X Protocol Version 11, Revision 0 [ 3706.783] Build Operating System: Linux 3.2.0-37-generic x86_64 Ubuntu [ 3706.783] Current Operating System: Linux ubuntu 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:20:46 UTC 2013 x86_64 [ 3706.783] Kernel command line: BOOT_IMAGE=/casper/vmlinuz.efi file=/cdrom/preseed/ubuntu.seed boot=casper nomodeset -- [ 3706.785] Build Date: 15 October 2013 09:23:37AM [ 3706.786] xorg-server 2:1.14.3-3ubuntu2 (For technical support please see http://www.ubuntu.com/support) [ 3706.786] Current version of pixman: 0.30.2 [ 3706.788] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 3706.788] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 3706.791] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Nov 2 12:28:52 2013 [ 3706.792] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 3706.792] (==) No Layout section. Using the first Screen section. [ 3706.792] (==) No screen section available. Using defaults. [ 3706.792] (**) |-->Screen "Default Screen Section" (0) [ 3706.792] (**) | |-->Monitor "<default monitor>" [ 3706.792] (==) No monitor specified for screen "Default Screen Section". Using a default monitor configuration. [ 3706.792] (==) Automatically adding devices [ 3706.792] (==) Automatically enabling devices [ 3706.792] (==) Automatically adding GPU devices [ 3706.792] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 3706.792] Entry deleted from font path. [ 3706.792] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist. [ 3706.792] Entry deleted from font path. [ 3706.792] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 3706.792] Entry deleted from font path. [ 3706.792] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist. [ 3706.792] Entry deleted from font path. [ 3706.792] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 3706.792] Entry deleted from font path. [ 3706.792] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/Type1, built-ins [ 3706.792] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" [ 3706.792] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 3706.792] (II) Loader magic: 0x7ff680918d20 [ 3706.792] (II) Module ABI versions: [ 3706.792] X.Org ANSI C Emulation: 0.4 [ 3706.792] X.Org Video Driver: 14.1 [ 3706.792] X.Org XInput driver : 19.1 [ 3706.792] X.Org Server Extension : 7.0 [ 3706.793] (--) PCI:*(0:0:2:0) 8086:0416:1462:10e8 rev 6, Mem @ 0xf7400000/4194304, 0xb0000000/268435456, I/O @ 0x0000f000/64 [ 3706.793] (II) Open ACPI successful (/var/run/acpid.socket) [ 3706.794] Initializing built-in extension Generic Event Extension [ 3706.795] Initializing built-in extension SHAPE [ 3706.796] Initializing built-in extension MIT-SHM [ 3706.797] Initializing built-in extension XInputExtension [ 3706.797] Initializing built-in extension XTEST [ 3706.798] Initializing built-in extension BIG-REQUESTS [ 3706.799] Initializing built-in extension SYNC [ 3706.799] Initializing built-in extension XKEYBOARD [ 3706.800] Initializing built-in extension XC-MISC [ 3706.801] Initializing built-in extension SECURITY [ 3706.802] Initializing built-in extension XINERAMA [ 3706.802] Initializing built-in extension XFIXES [ 3706.803] Initializing built-in extension RENDER [ 3706.804] Initializing built-in extension RANDR [ 3706.804] Initializing built-in extension COMPOSITE [ 3706.805] Initializing built-in extension DAMAGE [ 3706.806] Initializing built-in extension MIT-SCREEN-SAVER [ 3706.806] Initializing built-in extension DOUBLE-BUFFER [ 3706.807] Initializing built-in extension RECORD [ 3706.807] Initializing built-in extension DPMS [ 3706.808] Initializing built-in extension X-Resource [ 3706.809] Initializing built-in extension XVideo [ 3706.809] Initializing built-in extension XVideo-MotionCompensation [ 3706.810] Initializing built-in extension SELinux [ 3706.811] Initializing built-in extension XFree86-VidModeExtension [ 3706.811] Initializing built-in extension XFree86-DGA [ 3706.812] Initializing built-in extension XFree86-DRI [ 3706.812] Initializing built-in extension DRI2 [ 3706.812] (II) "glx" will be loaded by default. [ 3706.812] (WW) "xmir" is not to be loaded by default. Skipping. [ 3706.812] (II) LoadModule: "dri2" [ 3706.812] (II) Module "dri2" already built-in [ 3706.812] (II) LoadModule: "glamoregl" [ 3706.813] (II) Loading /usr/lib/xorg/modules/libglamoregl.so [ 3706.813] (II) Module glamoregl: vendor="X.Org Foundation" [ 3706.813] compiled for 1.14.2.901, module version = 0.5.1 [ 3706.813] ABI class: X.Org ANSI C Emulation, version 0.4 [ 3706.813] (II) LoadModule: "glx" [ 3706.813] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 3706.813] (II) Module glx: vendor="X.Org Foundation" [ 3706.813] compiled for 1.14.3, module version = 1.0.0 [ 3706.813] ABI class: X.Org Server Extension, version 7.0 [ 3706.813] (==) AIGLX enabled [ 3706.814] Loading extension GLX [ 3706.814] (==) Matched intel as autoconfigured driver 0 [ 3706.814] (==) Matched vesa as autoconfigured driver 1 [ 3706.814] (==) Matched modesetting as autoconfigured driver 2 [ 3706.814] (==) Matched fbdev as autoconfigured driver 3 [ 3706.814] (==) Assigned the driver to the xf86ConfigLayout [ 3706.814] (II) LoadModule: "intel" [ 3706.814] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so [ 3706.814] (II) Module intel: vendor="X.Org Foundation" [ 3706.814] compiled for 1.14.3, module version = 2.99.904 [ 3706.814] Module class: X.Org Video Driver [ 3706.814] ABI class: X.Org Video Driver, version 14.1 [ 3706.814] (II) LoadModule: "vesa" [ 3706.814] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so [ 3706.814] (II) Module vesa: vendor="X.Org Foundation" [ 3706.814] compiled for 1.14.1, module version = 2.3.2 [ 3706.814] Module class: X.Org Video Driver [ 3706.814] ABI class: X.Org Video Driver, version 14.1 [ 3706.814] (II) LoadModule: "modesetting" [ 3706.814] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so [ 3706.814] (II) Module modesetting: vendor="X.Org Foundation" [ 3706.814] compiled for 1.14.1, module version = 0.8.0 [ 3706.814] Module class: X.Org Video Driver [ 3706.814] ABI class: X.Org Video Driver, version 14.1 [ 3706.814] (II) LoadModule: "fbdev" [ 3706.814] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so [ 3706.815] (II) Module fbdev: vendor="X.Org Foundation" [ 3706.815] compiled for 1.14.1, module version = 0.4.3 [ 3706.815] Module class: X.Org Video Driver [ 3706.815] ABI class: X.Org Video Driver, version 14.1 [ 3706.815] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, HD Graphics, HD Graphics 2000, HD Graphics 3000, HD Graphics 2500, HD Graphics 4000, HD Graphics P4000, HD Graphics 4600, HD Graphics 5000, HD Graphics P4600/P4700, Iris(TM) Graphics 5100, HD Graphics 4400, HD Graphics 4200, Iris(TM) Pro Graphics 5200 [ 3706.815] (II) VESA: driver for VESA chipsets: vesa [ 3706.815] (II) modesetting: Driver for Modesetting Kernel Drivers: kms [ 3706.815] (II) FBDEV: driver for framebuffer: fbdev [ 3706.815] (--) using VT number 7 [ 3706.819] (WW) Falling back to old probe method for modesetting [ 3706.819] (EE) open /dev/dri/card0: No such file or directory [ 3706.819] (WW) Falling back to old probe method for fbdev [ 3706.819] (II) Loading sub module "fbdevhw" [ 3706.819] (II) LoadModule: "fbdevhw" [ 3706.819] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so [ 3706.819] (II) Module fbdevhw: vendor="X.Org Foundation" [ 3706.819] compiled for 1.14.3, module version = 0.0.2 [ 3706.819] ABI class: X.Org Video Driver, version 14.1 [ 3706.819] (II) Loading sub module "vbe" [ 3706.819] (II) LoadModule: "vbe" [ 3706.819] (II) Loading /usr/lib/xorg/modules/libvbe.so [ 3706.819] (II) Module vbe: vendor="X.Org Foundation" [ 3706.819] compiled for 1.14.3, module version = 1.1.0 [ 3706.819] ABI class: X.Org Video Driver, version 14.1 [ 3706.819] (II) Loading sub module "int10" [ 3706.819] (II) LoadModule: "int10" [ 3706.819] (II) Loading /usr/lib/xorg/modules/libint10.so [ 3706.819] (II) Module int10: vendor="X.Org Foundation" [ 3706.819] compiled for 1.14.3, module version = 1.0.0 [ 3706.819] ABI class: X.Org Video Driver, version 14.1 [ 3706.819] (II) VESA(0): initializing int10 [ 3706.820] (EE) VESA(0): V_BIOS address 0x0 out of range [ 3706.820] (II) UnloadModule: "vesa" [ 3706.820] (II) UnloadSubModule: "int10" [ 3706.820] (II) Unloading int10 [ 3706.820] (II) UnloadSubModule: "vbe" [ 3706.820] (II) Unloading vbe [ 3706.820] (EE) Screen(s) found, but none have a usable configuration. [ 3706.820] (EE) Fatal server error: [ 3706.820] (EE) no screens found(EE) [ 3706.820] (EE) Please consult the The X.Org Foundation support at http://wiki.x.org for help. [ 3706.820] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information. [ 3706.820] (EE) [ 3706.827] (EE) Server terminated with error (1). Closing log file. I also saved the dsmeg output to see if it can be of any help. In order to be able to get to this stage I had to boot with nomodeset option and removed quiet and splash. Anyone got this same error? Any guidance? I've tried other linux distros and so far the only one that is able to boot is Opensuse 12.3 without any issues (but only when I switch to legacy mode instead of UEFI).

    Read the article

  • C#/.NET Little Wonders: Interlocked Read() and Exchange()

    - by James Michael Hare
    Once again, in this series of posts I look at the parts of the .NET Framework that may seem trivial, but can help improve your code by making it easier to write and maintain. The index of all my past little wonders posts can be found here. Last time we discussed the Interlocked class and its Add(), Increment(), and Decrement() methods which are all useful for updating a value atomically by adding (or subtracting).  However, this begs the question of how do we set and read those values atomically as well? Read() – Read a value atomically Let’s begin by examining the following code: 1: public class Incrementor 2: { 3: private long _value = 0; 4:  5: public long Value { get { return _value; } } 6:  7: public void Increment() 8: { 9: Interlocked.Increment(ref _value); 10: } 11: } 12:  It uses an interlocked increment, as we discuss in my previous post (here), so we know that the increment will be thread-safe.  But, to realize what’s potentially wrong we have to know a bit about how atomic reads are in 32 bit and 64 bit .NET environments. When you are dealing with an item smaller or equal to the system word size (such as an int on a 32 bit system or a long on a 64 bit system) then the read is generally atomic, because it can grab all of the bits needed at once.  However, when dealing with something larger than the system word size (reading a long on a 32 bit system for example), it cannot grab the whole value at once, which can lead to some problems since this read isn’t atomic. For example, this means that on a 32 bit system we may read one half of the long before another thread increments the value, and the other half of it after the increment.  To protect us from reading an invalid value in this manner, we can do an Interlocked.Read() to force the read to be atomic (of course, you’d want to make sure any writes or increments are atomic also): 1: public class Incrementor 2: { 3: private long _value = 0; 4:  5: public long Value 6: { 7: get { return Interlocked.Read(ref _value); } 8: } 9:  10: public void Increment() 11: { 12: Interlocked.Increment(ref _value); 13: } 14: } Now we are guaranteed that we will read the 64 bit value atomically on a 32 bit system, thus ensuring our thread safety (assuming all other reads, writes, increments, etc. are likewise protected).  Note that as stated before, and according to the MSDN (here), it isn’t strictly necessary to use Interlocked.Read() for reading 64 bit values on 64 bit systems, but for those still working in 32 bit environments, it comes in handy when dealing with long atomically. Exchange() – Exchanges two values atomically Exchange() lets us store a new value in the given location (the ref parameter) and return the old value as a result. So just as Read() allows us to read atomically, one use of Exchange() is to write values atomically.  For example, if we wanted to add a Reset() method to our Incrementor, we could do something like this: 1: public void Reset() 2: { 3: _value = 0; 4: } But the assignment wouldn’t be atomic on 32 bit systems, since the word size is 32 bits and the variable is a long (64 bits).  Thus our assignment could have only set half the value when a threaded read or increment happens, which would put us in a bad state. So instead, we could write Reset() like this: 1: public void Reset() 2: { 3: Interlocked.Exchange(ref _value, 0); 4: } And we’d be safe again on a 32 bit system. But this isn’t the only reason Exchange() is valuable.  The key comes in realizing that Exchange() doesn’t just set a new value, it returns the old as well in an atomic step.  Hence the name “exchange”: you are swapping the value to set with the stored value. So why would we want to do this?  Well, anytime you want to set a value and take action based on the previous value.  An example of this might be a scheme where you have several tasks, and during every so often, each of the tasks may nominate themselves to do some administrative chore.  Perhaps you don’t want to make this thread dedicated for whatever reason, but want to be robust enough to let any of the threads that isn’t currently occupied nominate itself for the job.  An easy and lightweight way to do this would be to have a long representing whether someone has acquired the “election” or not.  So a 0 would indicate no one has been elected and 1 would indicate someone has been elected. We could then base our nomination strategy as follows: every so often, a thread will attempt an Interlocked.Exchange() on the long and with a value of 1.  The first thread to do so will set it to a 1 and return back the old value of 0.  We can use this to show that they were the first to nominate and be chosen are thus “in charge”.  Anyone who nominates after that will attempt the same Exchange() but will get back a value of 1, which indicates that someone already had set it to a 1 before them, thus they are not elected. Then, the only other step we need take is to remember to release the election flag once the elected thread accomplishes its task, which we’d do by setting the value back to 0.  In this way, the next thread to nominate with Exchange() will get back the 0 letting them know they are the new elected nominee. Such code might look like this: 1: public class Nominator 2: { 3: private long _nomination = 0; 4: public bool Elect() 5: { 6: return Interlocked.Exchange(ref _nomination, 1) == 0; 7: } 8: public bool Release() 9: { 10: return Interlocked.Exchange(ref _nomination, 0) == 1; 11: } 12: } There’s many ways to do this, of course, but you get the idea.  Running 5 threads doing some “sleep” work might look like this: 1: var nominator = new Nominator(); 2: var random = new Random(); 3: Parallel.For(0, 5, i => 4: { 5:  6: for (int j = 0; j < _iterations; ++j) 7: { 8: if (nominator.Elect()) 9: { 10: // elected 11: Console.WriteLine("Elected nominee " + i); 12: Thread.Sleep(random.Next(100, 5000)); 13: nominator.Release(); 14: } 15: else 16: { 17: // not elected 18: Console.WriteLine("Did not elect nominee " + i); 19: } 20: // sleep before check again 21: Thread.Sleep(1000); 22: } 23: }); And would spit out results like: 1: Elected nominee 0 2: Did not elect nominee 2 3: Did not elect nominee 1 4: Did not elect nominee 4 5: Did not elect nominee 3 6: Did not elect nominee 3 7: Did not elect nominee 1 8: Did not elect nominee 2 9: Did not elect nominee 4 10: Elected nominee 3 11: Did not elect nominee 2 12: Did not elect nominee 1 13: Did not elect nominee 4 14: Elected nominee 0 15: Did not elect nominee 2 16: Did not elect nominee 4 17: ... Another nice thing about the Interlocked.Exchange() is it can be used to thread-safely set pretty much anything 64 bits or less in size including references, pointers (in unsafe mode), floats, doubles, etc.  Summary So, now we’ve seen two more things we can do with Interlocked: reading and exchanging a value atomically.  Read() and Exchange() are especially valuable for reading/writing 64 bit values atomically in a 32 bit system.  Exchange() has value even beyond simply atomic writes by using the Exchange() to your advantage, since it reads and set the value atomically, which allows you to do lightweight nomination systems. There’s still a few more goodies in the Interlocked class which we’ll explore next time! Technorati Tags: C#,CSharp,.NET,Little Wonders,Interlocked

    Read the article

  • ANTS CLR and Memory Profiler In Depth Review (Part 2 of 2 &ndash; Memory Profiler)

    - by ToStringTheory
    One of the things that people might not know about me, is my obsession to make my code as efficient as possible. Many people might not realize how much of a task or undertaking that this might be, but it is surely a task as monumental as climbing Mount Everest, except this time it is a challenge for the mind… In trying to make code efficient, there are many different factors that play a part – size of project or solution, tiers, language used, experience and training of the programmer, technologies used, maintainability of the code – the list can go on for quite some time. I spend quite a bit of time when developing trying to determine what is the best way to implement a feature to accomplish the efficiency that I look to achieve. One program that I have recently come to learn about – Red Gate ANTS Performance (CLR) and Memory profiler gives me tools to accomplish that job more efficiently as well. In this review, I am going to cover some of the features of the ANTS memory profiler set by compiling some hideous example code to test against. Notice As a member of the Geeks With Blogs Influencers program, one of the perks is the ability to review products, in exchange for a free license to the program. I have not let this affect my opinions of the product in any way, and Red Gate nor Geeks With Blogs has tried to influence my opinion regarding this product in any way. Introduction – Part 2 In my last post, I reviewed the feature packed Red Gate ANTS Performance Profiler.  Separate from the Red Gate Performance Profiler is the Red Gate ANTS Memory Profiler – a simple, easy to use utility for checking how your application is handling memory management…  A tool that I wish I had had many times in the past.  This post will be focusing on the ANTS Memory Profiler and its tool set. The memory profiler has a large assortment of features just like the Performance Profiler, with the new session looking nearly exactly alike: ANTS Memory Profiler Memory profiling is not something that I have to do very often…  In the past, the few cases I’ve had to find a memory leak in an application I have usually just had to trace the code of the operations being performed to look for oddities…  Sadly, I have come across more undisposed/non-using’ed IDisposable objects, usually from ADO.Net than I would like to ever see.  Support is not fun, however using ANTS Memory Profiler makes this task easier.  For this round of testing, I am going to use the same code from my previous example, using the WPF application. This time, I will choose the ‘Profile Memory’ option from the ANTS menu in Visual Studio, which launches the solution in its currently configured state/start-up project, and then launches the ANTS Memory Profiler to help.  It prepopulates all of the fields with the current project information, and all I have to do is select the ‘Start Profiling’ option. When the window comes up, it is actually quite barren, just giving ideas on how to work the profiler.  You start by getting to the point in your application that you want to profile, and then taking a ‘Memory Snapshot’.  This performs a full garbage collection, and snapshots the managed heap.  Using the same WPF app as before, I will go ahead and take a snapshot now. As you can see, ANTS is already giving me lots of information regarding the snapshot, however this is just a snapshot.  The whole point of the profiler is to perform an action, usually one where a memory problem is being noticed, and then take another snapshot and perform a diff between them to see what has changed.  I am going to go ahead and generate 5000 primes, and then take another snapshot: As you can see, ANTS is already giving me a lot of new information about this snapshot compared to the last.  Information such as difference in memory usage, fragmentation, class usage, etc…  If you take more snapshots, you can use the dropdown at the top to set your actual comparison snapshots. If you beneath the timeline, you will see a breadcrumb trail showing how best to approach profiling memory using ANTS.  When you first do the comparison, you start on the Summary screen.  You can either use the charts at the bottom, or switch to the class list screen to get to the next step.  Here is the class list screen: As you can see, it lists information about all of the instances between the snapshots, as well as at the bottom giving you a way to filter by telling ANTS what your problem is.  I am going to go ahead and select the Int16[] to look at the Instance Categorizer Using the instance categorizer, you can travel backwards to see where all of the instances are coming from.  It may be hard to see in this image, but hopefully the lightbox (click on it) will help: I can see that all of these instances are rooted to the application through the UI TextBlock control.  This image will probably be even harder to see, however using the ‘Instance Retention Graph’, you can trace an objects memory inheritance up the chain to see its roots as well.  This is a simple example, as this is simply a known element.  Usually you would be profiling an actual problem, and comparing those differences.  I know in the past, I have spotted a problem where a new context was created per page load, and it was rooted into the application through an event.  As the application began to grow, performance and reliability problems started to emerge.  A tool like this would have been a great way to identify the problem quickly. Overview Overall, I think that the Red Gate ANTS Memory Profiler is a great utility for debugging those pesky leaks.  3 Biggest Pros: Easy to use interface with lots of options for configuring profiling session Intuitive and helpful interface for drilling down from summary, to instance, to root graphs ANTS provides an API for controlling the profiler. Not many options, but still helpful. 2 Biggest Cons: Inability to automatically snapshot the memory by interval Lack of complete integration with Visual Studio via an extension panel Ratings Ease of Use (9/10) – I really do believe that they have brought simplicity to the once difficult task of memory profiling.  I especially liked how it stepped you further into the drilldown by directing you towards the best options. Effectiveness (10/10) – I believe that the profiler does EXACTLY what it purports to do.  Features (7/10) – A really great set of features all around in the application, however, I would like to see some ability for automatically triggering snapshots based on intervals or framework level items such as events. Customer Service (10/10) – My entire experience with Red Gate personnel has been nothing but good.  their people are friendly, helpful, and happy! UI / UX (9/10) – The interface is very easy to get around, and all of the options are easy to find.  With a little bit of poking around, you’ll be optimizing Hello World in no time flat! Overall (9/10) – Overall, I am happy with the Memory Profiler and its features, as well as with the service I received when working with the Red Gate personnel.  Thank you for reading up to here, or skipping ahead – I told you it would be shorter!  Please, if you do try the product, drop me a message and let me know what you think!  I would love to hear any opinions you may have on the product. Code Feel free to download the code I used above – download via DropBox

    Read the article

  • ???Flashback Log???????Redo Log?

    - by Liu Maclean(???)
    ????????????????????redo log?   RVWR( Recovery Writer)?3s??flashback generate buffer??block before image?????????? ?????block change???RVWR??block before image ?flashback log? ?????????,Oracle???????????before image????????,????????flashback database logs?????   ???????????,????? ??????????????????,???????????before image?????shared pool??flashback log buffer?,RVWR??????flashback log buffer??????????? ?DBWR???????????????,DBWR?????buffer header??FBA(Flashback Byte Address)?flashback log buffer?????????? ???? ?????? ??? ????????????? , RVWR???????????(flashback markers)?flashback database logs?? ????(flashback markers)?????????????Oracle??flashback ??????????  ??????????, Oracle ??????(flashback markers)????????????flashback database log???????????block image; ??Oracle ???????(forward recovery)?????????????????SCN?????? flashback markers for example: **** Record at fba: (lno 1 thr 1 seq 1 bno 4 bof 8184) **** RECORD HEADER: Type: 3 (Skip) Size: 8132 RECORD DATA (Skip): **** Record at fba: (lno 1 thr 1 seq 1 bno 4 bof 52) **** RECORD HEADER: Type: 7 (Begin Crash Recovery Record) Size: 36 RECORD DATA (Begin Crash Recovery Record): Previous logical record fba: (lno 1 thr 1 seq 1 bno 3 bof 316) Record scn: 0x0000.00000000 [0.0] **** Record at fba: (lno 1 thr 1 seq 1 bno 3 bof 8184) **** RECORD HEADER: Type: 3 (Skip) Size: 7868 RECORD DATA (Skip): **** Record at fba: (lno 1 thr 1 seq 1 bno 3 bof 316) **** RECORD HEADER: Type: 2 (Marker) Size: 300 RECORD DATA (Marker): Previous logical record fba: (lno 0 thr 0 seq 0 bno 0 bof 0) Record scn: 0x0000.00000000 [0.0] Marker scn: 0x0000.0060e024 [0.6348836] 06/13/2012 15:56:35 Flag 0x0 Flashback threads: 1, Enabled redo threads 1 Recovery Start Checkpoint: scn: 0x0000.0060e024 [0.6348836] 06/13/2012 15:56:12 thread:1 rba:(0x80.180.10) Flashback thread Markers: Thread:1 status:0 fba: (lno 1 thr 1 seq 1 bno 2 bof 8184) Redo Thread Checkpoint Info: Thread:1 rba:(0x80.180.10) **** Record at fba: (lno 1 thr 1 seq 1 bno 2 bof 8184) **** RECORD HEADER: Type: 3 (Skip) Size: 8168 RECORD DATA (Skip): End-Of-Thread reached ????????????????block change ????before image????????flashback log?? ?????block change???flashback log record ????????? redo log???!????flashback log ???????before image ? redo log??? change vector ?  Oracle?????????????????????????????????????,??????I/O??????????????: ??hot block??,Oracle???????????block image?????; Oracle ?????????(flashback barriers)???????????????,flashback barriers???????(???15??),??????????(flashback barriers)????(flashback markers)????????? ????, ??????change?????, ???????????????????????????, ?15????????????????????flashback log????????before image?????????????,?????????????????????,?????????????? ????????,??????????????(flashback barriers), flashback barriers???????,?????15????? ?????flashback barriers????????(flashback markers)???????????????,???????????????????(????barriers?????)??????block image ,????????????????????????????????? ??????????flashback log????redo log????! ????,????????????????, ?????????? SQL> select * from v$version; BANNER -------------------------------------------------------------------------------- Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production PL/SQL Release 11.2.0.3.0 - Production CORE 11.2.0.3.0 Production TNS for Linux: Version 11.2.0.3.0 - Production NLSRTL Version 11.2.0.3.0 - Production SQL> select * from global_name; GLOBAL_NAME -------------------------------------------------------------------------------- www.oracledatabase12g.com SQL> create table flash_maclean (t1 varchar2(200)) tablespace users; Table created. SQL> insert into flash_maclean values('MACLEAN LOVE HANNA'); 1 row created. SQL> commit; Commit complete. SQL> startup force; ORACLE instance started. Total System Global Area 939495424 bytes Fixed Size 2233960 bytes Variable Size 713034136 bytes Database Buffers 218103808 bytes Redo Buffers 6123520 bytes Database mounted. Database opened. SQL> update flash_maclean set t1='HANNA LOVE MACLEAN'; 1 row updated. commit; Commit complete. SQL> alter system checkpoint; System altered. SQL> select dbms_rowid.rowid_block_number(rowid),dbms_rowid.rowid_relative_fno(rowid) from flash_maclean; DBMS_ROWID.ROWID_BLOCK_NUMBER(ROWID) DBMS_ROWID.ROWID_RELATIVE_FNO(ROWID) ------------------------------------ ------------------------------------ 140431 4 datafile 4 block 140431 ??RDBA rdba: 0x0102248f (4/140431) SQL> ! ps -ef|grep rvwr|grep -v grep oracle 26695 1 0 15:56 ? 00:00:00 ora_rvwr_G11R23 SQL> oradebug setospid 26695 Oracle pid: 20, Unix process pid: 26695, image: [email protected] (RVWR) SQL> ORADEBUG DUMP FBTAIL 1; Statement processed. To dump the last 2000 flashback records , ??ORADEBUG DUMP FBTAIL 1????????2000?????? SQL> oradebug tracefile_name /s01/orabase/diag/rdbms/g11r23/G11R23/trace/G11R23_rvwr_26695.trc ? TRACE?????????block? before image **** Record at fba: (lno 1 thr 1 seq 1 bno 55 bof 2564) **** RECORD HEADER: Type: 1 (Block Image) Size: 28 RECORD DATA (Block Image): file#: 4 rdba: 0x0102248f Next scn: 0x0000.00000000 [0.0] Flag: 0x0 Block Size: 8192 BLOCK IMAGE: buffer rdba: 0x0102248f scn: 0x0000.00609044 seq: 0x01 flg: 0x06 tail: 0x90440601 frmt: 0x02 chkval: 0xc626 type: 0x06=trans data Hex dump of block: st=0, typ_found=1 Dump of memory from 0x00002B1D94183C00 to 0x00002B1D94185C00 2B1D94183C00 0000A206 0102248F 00609044 06010000 [.....$..D.`.....] 2B1D94183C10 0000C626 00000001 00014AD4 0060903A [&........J..:.`.] 2B1D94183C20 00000000 00320002 01022488 00090006 [......2..$......] 2B1D94183C30 00000CC8 00C00340 000D0542 00008000 [[email protected].......] 2B1D94183C40 006040BC 000F000A 00000920 00C002E4 [.@`..... .......] 2B1D94183C50 0017048F 00002001 00609044 00000000 [..... ..D.`.....] 2B1D94183C60 00000000 00010100 0014FFFF 1F6E1F77 [............w.n.] 2B1D94183C70 00001F6E 1F770001 00000000 00000000 [n.....w.........] 2B1D94183C80 00000000 00000000 00000000 00000000 [................] Repeat 500 times 2B1D94185BD0 00000000 00000000 2C000000 4D120102 [...........,...M] 2B1D94185BE0 454C4341 4C204E41 2045564F 4E4E4148 [ACLEAN LOVE HANN] 2B1D94185BF0 01002C41 43414D07 4E41454C 90440601 [A,...MACLEAN..D.] Block header dump: 0x0102248f Object id on Block? Y seg/obj: 0x14ad4 csc: 0x00.60903a itc: 2 flg: E typ: 1 - DATA brn: 0 bdba: 0x1022488 ver: 0x01 opc: 0 inc: 0 exflg: 0 Itl Xid Uba Flag Lck Scn/Fsc 0x01 0x0006.009.00000cc8 0x00c00340.0542.0d C--- 0 scn 0x0000.006040bc 0x02 0x000a.00f.00000920 0x00c002e4.048f.17 --U- 1 fsc 0x0000.00609044 bdba: 0x0102248f data_block_dump,data header at 0x2b1d94183c64 =============== tsiz: 0x1f98 hsiz: 0x14 pbl: 0x2b1d94183c64 76543210 flag=-------- ntab=1 nrow=1 frre=-1 fsbo=0x14 fseo=0x1f77 avsp=0x1f6e tosp=0x1f6e 0xe:pti[0] nrow=1 offs=0 0x12:pri[0] offs=0x1f77 block_row_dump: tab 0, row 0, @0x1f77 tl: 22 fb: --H-FL-- lb: 0x2 cc: 1 col 0: [18] 4d 41 43 4c 45 41 4e 20 4c 4f 56 45 20 48 41 4e 4e 41 end_of_block_dump SQL> select dump('MACLEAN LOVE HANNA',16) from dual; DUMP('MACLEANLOVEHANNA',16) -------------------------------------------------------------------- Typ=96 Len=18: 4d,41,43,4c,45,41,4e,20,4c,4f,56,45,20,48,41,4e,4e,41 ???????????????????????,??flashback log??before image????????? create table flash_maclean1 (t1 int) tablespace users; SQL> select vs.name, ms.value 2 from v$mystat ms, v$sysstat vs 3 where vs.statistic# = ms.statistic# 4 and vs.name in ('redo size','db block changes'); NAME VALUE ---------------------------------------------------------------- ---------- db block changes 0 redo size 0 SQL> select name,value from v$sysstat where name like 'flashback log%'; NAME VALUE ---------------------------------------------------------------- ---------- flashback log writes 49 flashback log write bytes 9306112 SQL> begin 2 for i in 1..5000 loop 3 update flash_maclean1 set t1=t1+1; 4 commit; 5 end loop; 6 end; 7 / PL/SQL procedure successfully completed. SQL> select vs.name, ms.value 2 from v$mystat ms, v$sysstat vs 3 where vs.statistic# = ms.statistic# 4 and vs.name in ('redo size','db block changes'); NAME VALUE ---------------------------------------------------------------- ---------- db block changes 20006 redo size 3071288 SQL> select name,value from v$sysstat where name like 'flashback log%'; NAME VALUE ---------------------------------------------------------------- ---------- flashback log writes 52 flashback log write bytes 10338304 ??????????? ??hot block,???20006 ?block changes???? ??? 3000k ?redo log ? ??1000k? flashback log ?

    Read the article

  • Can't get the L2TP IPSEC up and running

    - by Maciej Swic
    i have an Ubuntu 11.10 (oneiric) server running on a ReadyNAS. Im planning to use this to accept ipsec+l2tp connections through a router. However, the connection is failing somewhere half through. Using Openswan IPsec U2.6.28/K3.0.0-12-generic and trying to connect with an iOS 5 iPhone 4S. This is how far i can get: auth.log: Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "PSK" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-NAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-noNAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "passthrough-for-non-l2tp" Jan 19 13:54:11 ubuntu pluto[1990]: listening for IKE messages Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying new style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying old style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo ::1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 2001:470:28:81:a00:27ff:* Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/etc/ipsec.secrets" Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/var/lib/openswan/ipsec.secrets.inc" Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [Dead Peer Detection] Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: responding to Main Mode from unknown peer 95.*.*.233 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R1: sent MR1, expecting MI2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R2: sent MR2, expecting MI3 Jan 19 14:05:03 ubuntu pluto[1990]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 95.*.*.233 port 500, complainant 95.*.*.233: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Router config UDP 500, 1701 and 4500 forwarded to 192.168.19.99 (Ubuntu server for ipsec). Ipsec passthrough enabled. /etc/ipsec.conf # /etc/ipsec.conf - Openswan IPsec configuration file # This file: /usr/share/doc/openswan/ipsec.conf-sample # # Manual: ipsec.conf.5 version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes #charonstart=yes #plutostart=yes protostack=netkey conn PSK authby=secret forceencaps=yes pfs=no auto=add keyingtries=3 dpdtimeout=60 dpdaction=clear rekey=no left=192.168.19.99 leftnexthop=192.168.19.1 leftprotoport=17/1701 right=%any rightprotoport=17/%any rightsubnet=vhost:%priv,%no dpddelay=10 #dpdtimeout=10 #dpdaction=clear include /etc/ipsec.d/l2tp-psk.conf /etc/ipsec.d/l2tp-psk.conf conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT # # PreSharedSecret needs to be specified in /etc/ipsec.secrets as # YourIPAddress %any: "sharedsecret" authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=192.168.19.99 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "0" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port, but propose "0" instead of their port. rightprotoport=17/%any dpddelay=10 dpdtimeout=10 dpdaction=clear conn passthrough-for-non-l2tp type=passthrough left=192.168.19.99 leftnexthop=192.168.19.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/ipsec.secrets include /var/lib/openswan/ipsec.secrets.inc %any %any: PSK "my-key" 192.168.19.99 %any: PSK "my-key" /etc/xl2tpd/xl2tpd.conf [global] debug network = yes debug tunnel = yes ipsec saref = no listen-addr = 192.168.19.99 [lns default] ip range = 192.168.19.201-192.168.19.220 local ip = 192.168.19.99 require chap = yes refuse chap = no refuse pap = no require authentication = no ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd pcp-accept-local ipcp-accept-remote noccp auth crtscts idle 1800 mtu 1410 mru 1410 defaultroute debug lock proxyarp connect-delay 5000 ipcp-accept-local /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses maciekish * my-secret * * maciekish my-secret * I can't seem to find the problem. Other ipsec connections to other hosts work from the network im currently at.

    Read the article

  • HAProxy: Display a "BADREQ" | BADREQ's by the thousands

    - by GruffTech
    My HAProxy Configuration. #HA-Proxy version 1.3.22 2009/10/14 Copyright 2000-2009 Willy Tarreau <[email protected]> global maxconn 10000 spread-checks 50 user haproxy group haproxy daemon stats socket /tmp/haproxy log localhost local0 log localhost local1 notice defaults mode http maxconn 50000 timeout client 10000 option forwardfor except 127.0.0.1 option httpclose option httplog listen dcaustin 0.0.0.0:80 mode http timeout connect 12000 timeout server 60000 timeout queue 120000 balance roundrobin option httpchk GET /index.html log global option httplog option dontlog-normal server web1 10.10.10.101:80 maxconn 300 check fall 1 server web2 10.10.10.102:80 maxconn 300 check fall 1 server web3 10.10.10.103:80 maxconn 300 check fall 1 server web4 10.10.10.104:80 maxconn 300 check fall 1 listen stats 0.0.0.0:9000 mode http balance log global timeout client 5000 timeout connect 4000 timeout server 30000 stats uri /haproxy HAProxy is running, and the socket is working... adam@dcaustin:/etc/haproxy# echo "show info" | socat stdio /tmp/haproxy Name: HAProxy Version: 1.3.22 Release_date: 2009/10/14 Nbproc: 1 Process_num: 1 Pid: 6320 Uptime: 0d 0h14m58s Uptime_sec: 898 Memmax_MB: 0 Ulimit-n: 20017 Maxsock: 20017 Maxconn: 10000 Maxpipes: 0 CurrConns: 47 PipesUsed: 0 PipesFree: 0 Tasks: 51 Run_queue: 1 node: dcaustin desiption: Errors show nothing from socket... adam@dcaustin:/etc/haproxy# echo "show errors" | socat stdio /tmp/haproxy adam@dcaustin:/etc/haproxy# However... My Error log is exploding with "badrequests" with the Error code cR. cR (according to 1.3 documentation) is The "timeout http-request" stroke before the client sent a full HTTP request. This is sometimes caused by too large TCP MSS values on the client side for PPPoE networks which cannot transport full-sized packets, or by clients sending requests by hand and not typing fast enough, or forgetting to enter the empty line at the end of the request. The HTTP status code is likely a 408 here. Correct on the 408, but we're getting literally thousands of these requests every hour. (This log snippet is an clip for about 10 seconds of time...) Jun 30 11:08:52 localhost haproxy[6320]: 92.22.213.32:26448 [30/Jun/2011:11:08:42.384] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10002 408 212 - - cR-- 35/35/18/0/0 0/0 "<BADREQ>" Jun 30 11:08:54 localhost haproxy[6320]: 71.62.130.24:62818 [30/Jun/2011:11:08:44.457] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10001 408 212 - - cR-- 39/39/16/0/0 0/0 "<BADREQ>" Jun 30 11:08:55 localhost haproxy[6320]: 84.73.75.236:3589 [30/Jun/2011:11:08:45.021] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10008 408 212 - - cR-- 35/35/15/0/0 0/0 "<BADREQ>" Jun 30 11:08:55 localhost haproxy[6320]: 69.39.20.190:49969 [30/Jun/2011:11:08:45.709] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10000 408 212 - - cR-- 37/37/16/0/0 0/0 "<BADREQ>" Jun 30 11:08:56 localhost haproxy[6320]: 2.29.0.9:58772 [30/Jun/2011:11:08:46.846] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10001 408 212 - - cR-- 43/43/22/0/0 0/0 "<BADREQ>" Jun 30 11:08:57 localhost haproxy[6320]: 212.139.250.242:57537 [30/Jun/2011:11:08:47.568] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10000 408 212 - - cR-- 42/42/21/0/0 0/0 "<BADREQ>" Jun 30 11:08:58 localhost haproxy[6320]: 74.79.195.75:55046 [30/Jun/2011:11:08:48.559] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10000 408 212 - - cR-- 46/46/24/0/0 0/0 "<BADREQ>" Jun 30 11:08:58 localhost haproxy[6320]: 74.79.195.75:55044 [30/Jun/2011:11:08:48.554] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10004 408 212 - - cR-- 45/45/24/0/0 0/0 "<BADREQ>" Jun 30 11:08:58 localhost haproxy[6320]: 74.79.195.75:55045 [30/Jun/2011:11:08:48.554] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10005 408 212 - - cR-- 44/44/24/0/0 0/0 "<BADREQ>" Jun 30 11:09:00 localhost haproxy[6320]: 68.197.56.2:52781 [30/Jun/2011:11:08:50.975] dcaustin dcaustin/<NOSRV> -1/-1/-1/-1/10000 408 212 - - cR-- 49/49/28/0/0 0/0 "<BADREQ>" From what I read on google, if i wanted to see what the bad requests are, I can show errors to the socket and it will spit them out. We do run a pretty heavily trafficed website and the percentage of "BADREQS" to normal requests is quite low, but I'd like to be able to get ahold of what that request WAS so I can debug it. stats # pxname,svname,qcur,qmax,scur,smax,slim,stot,bin,bout,dreq,dresp,ereq,econ,eresp,wretr,wredis,status,weight,act,bck,chkfail,chkdown,lastchg,downtime,qlimit,pid,iid,sid,throttle,lbtot,tracked,type,rate,rate_lim,rate_max, dcaustin,FRONTEND,,,64,120,50000,88433,105889100,2553809875,0,0,4641,,,,,OPEN,,,,,,,,,1,1,0,,,,0,45,0,128, dcaustin,web1,0,0,10,28,300,20941,25402112,633143416,,0,,0,3,0,0,UP,1,1,0,0,0,2208,0,,1,1,1,,20941,,2,11,,30, dcaustin,web2,0,0,9,30,300,20941,25026691,641475169,,0,,0,3,0,0,UP,1,1,0,0,0,2208,0,,1,1,2,,20941,,2,11,,30, dcaustin,web3,0,0,10,27,300,20940,30116527,635015040,,0,,0,9,0,0,UP,1,1,0,0,0,2208,0,,1,1,3,,20940,,2,10,,31, dcaustin,web4,0,0,5,28,300,20940,25343770,643209546,,0,,0,8,0,0,UP,1,1,0,0,0,2208,0,,1,1,4,,20940,,2,11,,31, dcaustin,BACKEND,0,0,34,95,50000,83762,105889100,2553809875,0,0,,0,34,0,0,UP,4,4,0,,0,2208,0,,1,1,0,,83762,,1,43,,122, 88500 "Sessions" and 4500 errors. in the last 20 minutes.

    Read the article

  • Juniper SSG-5 subinterface vlan routing to the internet

    - by catfish
    I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

    Read the article

  • Can't get FTP to work on centOS 5.6

    - by josi
    Hi guys I have been trying for a few hours to install and get FTP to work... I did yum install ftp and yum install vsftpd They all installed and are running but when I try to use filezilla or some other client I just can't connect....I've tried connecting on port 21 and port 990 ....nothing! These are my iptables # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p esp -j ACCEPT -A RH-Firewall-1-INPUT -p ah -j ACCEPT -A RH-Firewall-1-INPUT -d 224.0.0.251 -p udp -m udp --dport 5353 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 110 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 990 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 465 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 646 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 993 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 995 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10009 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 7778 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5000 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25566 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8765 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8192 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8123 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 20 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m state --state NEW -m udp --dport 23877 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 9091 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 51413 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10011 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 30033 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT Any help would be much appreciated! If I do lsof -i :21 without the "." it shows nothing. [root@ks3000420 ~]# lsof -i :21 . COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME bash 9964 root cwd DIR 8,1 4096 483329 . bash 11608 root cwd DIR 8,1 4096 483329 . bash 13550 root cwd DIR 8,1 4096 483329 . vi 14117 root cwd DIR 8,1 4096 483329 . sftp-serv 15261 root cwd DIR 8,1 4096 483329 . sftp-serv 15477 root cwd DIR 8,1 4096 483329 . bash 19074 root cwd DIR 8,1 4096 483329 . lsof 19100 root cwd DIR 8,1 4096 483329 . lsof 19101 root cwd DIR 8,1 4096 483329 .

    Read the article

  • MySQL is hogging my server resources

    - by Reacen
    Does anyone have any idea of what can cause this weird behaviour and how I go about fixing it? This is all coming from MySQL only (both RAM and CPU usage), for about 10 minutes after I reboot my Java game server (that has a pool of 256 connections). There are not that many queries and I think it may be more of a MySQL misconfiguration problem. My server: 3.20 GHz * 6 core / 24 GB RAM / 64 bit Windows Server 2003. My game server: Java server, with 256 MySQL connections pool (MyISAM engine), about 500,000 accounts, and 9 million rows of game items in database and about 3,000 players are connected. After about 15 minutes of the game server reboot, the server resumes its stability and CPU usage drop down to 1% ~ 5% and memory to 6 GB. Here is a copy of my MySQL configuration. Also, any advice about my MySQL configuration will be appreciated. I really set it up almost at random. # Example MySQL config file for very large systems. # # This is for a large system with memory of 1G-2G where the system runs mainly # MySQL. # # You can copy this file to # /etc/my.cnf to set global options, # mysql-data-dir/my.cnf to set server-specific options (in this # installation this directory is C:\mysql\data) or # ~/.my.cnf to set user-specific options. # # In this file, you can use all long options that a program supports. # If you want to know which options a program supports, run the program # with the "--help" option. # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /tmp/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] #log=c:\mysql.log port = 3306 socket = /tmp/mysql.sock skip-locking key_buffer_size = 2572M max_allowed_packet = 64M table_open_cache = 512 sort_buffer_size = 128M read_buffer_size = 128M read_rnd_buffer_size = 128M myisam_sort_buffer_size = 500M thread_cache_size = 32 query_cache_size = 1948M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 12 max_connections = 5000 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # #skip-networking # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 # Replication Slave (comment out master section to use this) # # To configure this host as a replication slave, you can choose between # two methods : # # 1) Use the CHANGE MASTER TO command (fully described in our manual) - # the syntax is: # # CHANGE MASTER TO MASTER_HOST=<host>, MASTER_PORT=<port>, # MASTER_USER=<user>, MASTER_PASSWORD=<password> ; # # where you replace <host>, <user>, <password> by quoted strings and # <port> by the master's port number (3306 by default). # # Example: # # CHANGE MASTER TO MASTER_HOST='125.564.12.1', MASTER_PORT=3306, # MASTER_USER='joe', MASTER_PASSWORD='secret'; # # OR # # 2) Set the variables below. However, in case you choose this method, then # start replication for the first time (even unsuccessfully, for example # if you mistyped the password in master-password and the slave fails to # connect), the slave will create a master.info file, and any later # change in this file to the variables' values below will be ignored and # overridden by the content of the master.info file, unless you shutdown # the slave server, delete master.info and restart the slaver server. # For that reason, you may want to leave the lines below untouched # (commented) and instead use CHANGE MASTER TO (see above) # # required unique id between 2 and 2^32 - 1 # (and different from the master) # defaults to 2 if master-host is set # but will not function as a slave if omitted #server-id = 2 # # The replication master for this slave - required #master-host = <hostname> # # The username the slave will use for authentication when connecting # to the master - required #master-user = <username> # # The password the slave will authenticate with when connecting to # the master - required #master-password = <password> # # The port the master is listening on. # optional - defaults to 3306 #master-port = <port> # # binary logging - not required for slaves, but recommended #log-bin=mysql-bin # # binary logging format - mixed recommended #binlog_format=mixed # Point the following paths to different dedicated disks #tmpdir = /tmp/ #log-update = /path-to-dedicated-directory/hostname # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = C:\mysql\data/ #innodb_data_file_path = ibdata1:2000M;ibdata2:10M:autoextend #innodb_log_group_home_dir = C:\mysql\data/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 384M #innodb_additional_mem_pool_size = 20M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 100M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 [mysqldump] quick max_allowed_packet = 64M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [myisamchk] key_buffer_size = 256M sort_buffer_size = 256M read_buffer = 8M write_buffer = 8M [mysqlhotcopy] interactive-timeout

    Read the article

  • How would you shorten 5,000+ URLs? [closed]

    - by Tyler J Fisher
    How would you go about shortening approximately 5,000 permalinks? The links point to a remote media archiving server, and are unlikely to change. Example URLs: rtsp://foo-1.bar.com/xx/xx/xx/xx.rm http://media.foo.org/xx/xx/xx.mp4 The URLs are going to be stored in a local MySQL database, as such it's crucial that the URLs are in a manageable form (i.e bit.ly or ow.ly). There are bulk URL shortening services, but those only allow shortening of 100 links/day, which isn't technically feasible so I need to think of something else.

    Read the article

  • What type of VPS stats should I look for?

    - by Dave
    I have a few websites that average a total of 10,000 uniques a day across my network. I also have a few mobile apps that pull xml data maybe 5,000 calls a day. My sites aren't anything major just a few wallpaper websites and few other small sites, nothing real database intensive. I currently own a dedicated server and I feel like it's overkill for my network. I'm looking into getting a Virtual Private Server (VPS). I was just wondering what kind of stats I should be looking for to support my network of sites. Thanks

    Read the article

  • Nginx + Haproxy + Thin + Rails - 503 Service Unavailable -

    - by Luca G. Soave
    I don't know how troubleshoot this. I get "503 Service Unavailable" http error for all "nginx upstreams" proxy passing calls to haproxy fast_thin and slow_thin ( server 127.0.0.1:3100 and server 127.0.0.1:3200 ), which loadbalance on 6 Thin servers ( 127.0.0.1:3000 .. 3005 ). Static files like /blog are currently fine. The falldown is: nginx on port 80 - haproxy on 3100 and 3200 - thin on 3000 .. 3005 and then Rails. Here it is /etc/nginx/nginx.conf : user nginx; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; sendfile on; tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; include /etc/nginx/conf.d/*.conf; } then /etc/nginx/conf.d/default.conf upstream fast_thin { server 127.0.0.1:3100; } upstream slow_thin { server 127.0.0.1:3200; } server { listen 80; server_name www.gitwatcher.com; rewrite ^/(.*) http://gitwatcher.com/$1 permanent; } server { listen 80; server_name gitwatcher.com; access_log /var/www/gitwatcher/log/access.log; error_log /var/www/gitwatcher/log/error.log; root /var/www/gitwatcher/public; # index index.html; location /about { proxy_pass http://fast_thin; break; } location /trends { proxy_pass http://slow_thin; break; } location /categories { proxy_pass http://slow_thin; break; } location /signout { proxy_pass http://slow_thin; break; } location /auth/github { proxy_pass http://slow_thin; break; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (-f $request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f $request_filename.html) { rewrite (.*) $1.html break; } if (!-f $request_filename) { proxy_pass http://slow_thin; break; } } } then haproxy config file /etc/haproxy/haproxy.cfg : global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet nbproc 1 # number of processing cores defaults log global retries 3 maxconn 2000 contimeout 5000 mode http clitimeout 60000 # maximum inactivity time on the client side srvtimeout 30000 # maximum inactivity time on the server side timeout connect 4000 # maximum time to wait for a connection attempt to a server to succeed option httplog option dontlognull option redispatch option httpclose # disable keepalive (HAProxy does not yet support the HTTP keep-alive mode) option abortonclose # enable early dropping of aborted requests from pending queue option httpchk # enable HTTP protocol to check on servers health option forwardfor # enable insert of X-Forwarded-For headers balance roundrobin # each server is used in turns, according to assigned weight stats enable # enable web-stats at /haproxy?stats stats auth haproxy:pr0xystats # force HTTP Auth to view stats stats refresh 5s # refresh rate of stats page listen rails_proxy 127.0.0.1:3100 # - equal weights on all servers # - maxconn will queue requests at HAProxy if limit is reached # - minconn dynamically scales the connection concurrency (bound my maxconn) depending on size of HAProxy queue # - check health every 20000 microseconds server web1 127.0.0.1:3000 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3001 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3002 weight 1 minconn 3 maxconn 6 check inter 20000 listen slow_proxy 127.0.0.1:3200 # cluster for slow requests, lower the queues, check less frequently server slow1 127.0.0.1:3003 weight 1 minconn 1 maxconn 3 check inter 40000 server slow2 127.0.0.1:3004 weight 1 minconn 1 maxconn 3 check inter 40000 server slow3 127.0.0.1:3005 weight 1 minconn 1 maxconn 3 check inter 40000 and the Thin config file /etc/thin/gitwatcher.yml : --- chdir: /var/www/gitwatcher environment: production address: 0.0.0.0 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 100 require: [] wait: 30 servers: 6 daemonize: true if I look into open listen ports, I got the following : root@fullness:/var/www/gitwatcher# lsof | grep TCP | egrep "nginx|haproxy|thin" nginx 834 root 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 835 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 837 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) haproxy 1908 haproxy 4u IPv4 11699 0t0 TCP localhost:3100 (LISTEN) haproxy 1908 haproxy 6u IPv4 11701 0t0 TCP localhost:3200 (LISTEN) root@fullness:/var/www/gitwatcher# iptables -L get me the following : Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:22222 ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT all -- anywhere anywhere DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Any help ?

    Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >