Search Results

Search found 2344 results on 94 pages for 'ethernet'.

Page 34/94 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Command-line connect to wired network for Ubuntu

  - by Tim

  I like to know how to use command-line to connect to a wired network in general for Ubuntu 8.10? In my case, I connect a cable to my laptop but it doesn't work with my WICD. So I like to try command-line method. Here is the ifconfig of my network adapters: $ ifconfig eth0 Link encap:Ethernet HWaddr 00:c0:9f:8d:23:74 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 Base address:0x1800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4457 errors:0 dropped:0 overruns:0 frame:0 TX packets:4457 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:493002 (493.0 KB) TX bytes:493002 (493.0 KB) wlan0 Link encap:Ethernet HWaddr 00:0e:9b:ab:56:19 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:576 Metric:1 RX packets:1508929 errors:0 dropped:0 overruns:0 frame:0 TX packets:768144 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:806027375 (806.0 MB) TX bytes:78834873 (78.8 MB) wlan0:avahi Link encap:Ethernet HWaddr 00:0e:9b:ab:56:19 inet addr:169.254.5.92 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:576 Metric:1 wmaster0 Link encap:UNSPEC HWaddr 00-0E-9B-AB-56-19-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Thanks and regards! UPDATE: Tried what oyvindio suggested. Here is the failing message: $ sudo dhclient3 eth0 There is already a pid file /var/run/dhclient.pid with pid 18279 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ mon0: unknown hardware address type 803 wmaster0: unknown hardware address type 801 mon0: unknown hardware address type 803 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:c0:9f:8d:23:74 Sending on LPF/eth0/00:c0:9f:8d:23:74 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 No DHCPOFFERS received. No working leases in persistent database - sleeping.

  Read the article

• Can't bring NAT to work

  - by user31738

  Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

  Read the article

• OSX Parallels 5 - can't share internet connection when using host-only networking...

  - by Steve Kirtley

  I've just upgraded from Parallels 3 to Parallels 5, but am having a problem matching my previous configuration. I am a web developer so run a local web server on my mac. I used to allow access to this from the virtual machines in Parallels by using 'Host-Only Networking' and then in OSX enabling internet sharing from my wifi/ethernet to the virtual ethernet ports that Parallels created. The setup was based on: http://www.craigfrancis.co.uk/features/setup/parallels/ The new version of Parallels doesn't create any network adaptors that are available for internet sharing in OSX - just VNIC's which only show under an ifconfig... Can anyone suggest how to make this all play nice? Thanks in advance! Steve

  Read the article

• How can I fix my WRT54GL's constant crashing?

  - by Aarthi

  I have a Linksys WRT54GL wireless router (the old blue-and-black) whose underside indicates it is Version 2. I've noticed that, on wireless mode, if I am on a Skype call or in a Google Hangout, the wireless aspect will crash completely. In addition, if I am connected via an ethernet cord, my quality (that is, how my voice is received) tanks very quickly. I suspect this is due, in part, to my internet connectivity itself (I'm on Comcast instead of Verizon FiOS, as I'd prefer) but I'd like to stop my wireless router's wireless capability from crashing. I considered a firmware upgrade, but it looks to me as if I am upgraded. Short of manually running ethernet all over my house, I'm not sure what to do. How can I solve my wireless router's issues? If the answer is "buy a new router," then that's valid, as well, in my opinion.

  Read the article

• replacing 3 Cisco Catalyst 4500

  - by hoberion

  Our network supplier recommends replacing our 3 cisco catalyst 4500's because they are EOL and dont speak OSPF (which we really want) Its not my area of expertise so I cant say for sure if we really need to replace these units but for my company the estimated costs of 250K euro is a huge problem. Is there any way to cut down on costs (without moving from cisco devices), I heard the 4500´s can speak ospf but would need an upgrade of sorts? edit: version: IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(20)EW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) supervisor: WS-X4013+ Cisco Catalyst 4500 Series Supervisor Engine II-Plus density: WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)

  Read the article

• Use wired LAN adapter by default

  - by Frantumn

  I am trying to find out if there's a way to set up network adapters so that if 2 are connected with network and internet access it will choose one over the other. Scenario: I have seen several computers running Windows 7 or Windows 8 where you are connected to a wireless network, working perfectly. Then when you plug in an Ethernet cable, it still shows the network icon in the taskbar as wireless. I would like to have my computer set up so that if there's an Ethernet cable plugged in, it uses that, and not the wireless adapter. 1) Is this possible / How? 2) Why does it stay on wireless over wired when given the option for both?

  Read the article

• Connect to development server via switch?

  - by letseatfood

  I apologize upfront if this isn't appropriate for superuser. I asked it on serverfault and was told it was too general for that site. I have a laptop with Vista and it receives it's internet connection wireless. I have an old desktop with Ubuntu 10.04 Server Edition installed and it is setup as a development server with Apache, MySQL, and PHP. This works well, with the server having a static IP address. The server is connected to the router via an Ethernet cable. Is it possible to disconnect the cable that is currently connecting the server and the router, then connect the server and workstation to a switch, so that I am still able to connect to the server via web browser from the workstation? I am trying to eliminate the long ethernet cable connecting the server to the router in the other room. I already have a switch, that is why I asked specifically about it. Thanks and I will be more than happy to clarify!

  Read the article

• Ubuntu: disable udev's persistent-net-generator.rules

  - by Luke404

  I'm using Ubuntu 12.04 LTS server edition and I am modifying /etc/udev/rules.d/70-persistent-net.rules to define my own mappings of ethernet interfaces to MAC addresses; that file is initially generated by rules in /lib/udev/rules.d/75-persistent-net-generator.rules at system installation time (or at the first boot, I actually don't know and it doesn't matter here). How can I be sure that my edited version will never ever be overwritten by anything? Removing the persistent-net-generator, as suggested on some websites, is not the Right Thing™ to do as told by comments in the file itself: it will be overwritten by any update of the udev package. I'm looking for a more formally correct way to disable it. Is it enough to just make sure that /etc/udev/rules.d/70-persistent-net.rules does exist? Maybe there are other events that could trigger its regeneration? (eg. adding or removing ethernet interfaces to the system?)

  Read the article

• What are the mandatory Linux kernel modules to run inside of ESXi

  - by Marcin

  I'm used to rolling my own kernels for servers, as it nicely minimizes the number of exploits (and the resulting patches) to take care of. In a traditional (bare metal) world, the whole process is about knowing what you have (hardware), and what you need (Ethernet, IPv4, iptables, etc.) In a virtualized environment, some things stay the same (still need Ethernet and IPv4), some things go away (power management), and then there are some new needs (vxnet3, or vmware-tools, even though that's compiled outside of the kernel). So my question mostly concerns itself with the last two categories: what can I remove completely, and what new stuff do I want? For example, what IO scheduler do I want, if all my disk operations are going through another filesystem/scheduler/cache to get to the virtual disk? Do I need hyper-threading enabled, or is the VM going to show them to me anyway as a CPU anyway? Do I need Large Receive Offload turned on, or is that something that the hypervisor's network drivers are going to do for me?

  Read the article

• Monitor Bonded Interface for Disconnection

  - by bradlis7

  I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

  Read the article

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

• Wireless bridge between two prolink adsl modem/router

  - by MyName

  Allright, so i've got 2 prolink hurricane h5004n. Its a broadband adsl modem and router. My Pc is connected to the first one via ethernet. What i want to do is a wireless bridge to make the 2 routers "talk". I've tried hooking up the dsl cable (as they are modems) in both to try but when one disconnects as the other connects. I don't really know about the configurations to be done of all the DCHP or RIP and NAT forwarding stuffs. (i'm just writing what i saw) In short i want the second router to act as a wifi repeater but i don't see any repeater option and i also do not want to connect them via ethernet. So is it possible to do something? Apart from buying another repeater i don't want to spend anymore i'm done :S

  Read the article

• Intel PRO/1000 Server NIC on Windows latency. How to measure?

  - by Bobb

  Please note - this question is about latency of the card itself. Not latency of internet or anything else. Thank you for your attention on this matter. It is often said that good server NIC does make difference compared to low grade cards and on-board Ethernet chips. I understand that on-board chip will likely consume CPU time and stand-alone card would use its own chip. Also server card would be faster than low-grade card. Are these 2 facts explaining most of the server cards advantages over on-board and low-grade cards ethernet? How would you measure latency on the card itself? I saw some reports stating some microseconds figures of NIC latency but I dont see how to measure that... Any advise will be appreciated.

  Read the article

• Cat5 wiring in my home [closed]

  - by Mike

  I have problem with cat5 cabling First I ran a length of cable 30 metres to my bedroom 1 and and connected both ends to a wall sockets internally using my punch down tool, both ends look fine. I also ran a cable from bedroom 1 to bedroom 2 so my son can use same internet connection , i then parallel connected my cables in bedroom 1 against using punch down tool using same colours all the way through. I ran a Ethernet cable from modem to first wall socket close to it then at bedroom end used another Ethernet cable to connect pc, it wouldn't connect to pc so I disconnected bedroom 2 cable from bedroom 1 socket. I connected bedroom 1 to pc and it worked, but how do I connect bedroom 2 (obviously cat 5 cable bedroom 1 to 2 is in place) As soon as I connect one wire from bedroom2 I loose Internet connection!

  Read the article

• Can a switch consume bandwidth?

  - by aashiq

  I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

  Read the article

• How to show disconnect network drives

  - by Jake

  Windows 7 and Vista laptops in my company domain has network drives set up by Win2k8 Server GPO. Normally, when the laptops has ethernet cable plugged in before boot, the network drives connect and appear as expected at the end of startup sequence. However, when the laptop has ethernet cable unplugged, the network drives are not connected, which is fine, but the disconnected icons disappear as well. i.e. the drives are not set up. At the end of the startup sequence, upon reaching desktop, the wireless adapters will connect to the network and the laptop will be able to find the network drive. Hence I want the drives to be setup nonetheless, so that the next attempt to connect, say, via a desktop shortcut, will reestablish the network drive connection. How can this be done?

  Read the article

• Areca 1880ix RAID hangs

  - by Dave

  Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

  Read the article

• how do i automatically add a new route to the routing table?

  - by Robbie Mckennie

  I'm looking at linking two networks with a long range Ethernet bridge. I know I can connect my two networks with a router, but my problem is how will my computers know where to send packets if I don't add the route manually? I COULD add them manually, but it seems like a hassle. I have very very limited knowledge of RIP (I know it has something to do with routing), but I don't know how to use it. edit: My vision for the network would be the 2 networks (which are currently independent home networks), connected by a microwave Ethernet link. I assumed i'd need a router on one end of the bridge, to handle communication between the 2 networks.

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• Bridging two connections in windows 7

  - by Serban Razvan

  I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

  Read the article

• Why does Windows Firewall show "Unidentified network" as one of my "Active public networks"?

  - by MousePad

  I have a machine that has wifi and ethernet. I have wifi active, and am not using ethernet. My Windows firewall shows two active networks, one is the wifi network I connect to, and the other is "Unidentified network". What is this unidentified network? I can't seem to be able to get rid of it because I can't find where it is even defined. How can you detect this and know whether this is just something appropriate or possibly a security problem? I am on Windows 7 64bit.

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >