Search Results

Search found 22036 results on 882 pages for 'vpn service'.

Page 34/882 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Any consumer routers with Outgoing VPN support?

  - by Brian Lacy

  When I'm working at home, I need to be able to connect to three different outgoing VPNs, two of which happen to use the same internal IP addressing schemes (192.168.0.*). I also need a static address for my VirtualBox VM so I can connect to my testing web server. Are there any routers which will allow me to connect to multiple outgoing VPNs and assign different internal IP addresses through NAT? Is such a thing even possible, or are there alternate solutions available? Thanks!

  Read the article

• PFSence VPN Routing

  - by SvrGuy

  We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

  Read the article

• Masquerade traffic from certain source IP to VPN connection

  - by Shuo Ran

  Network Setup: 10.0.0.1 Router: to internet 10.0.0.70 Server: Ubuntu based server,default gateway is 10.0.0.1 10.0.0.51 PC I created a PPTP connection(interface: ppp0) on Server to a machine on the internet, what I want to do is route all the traffic from certain IP address(10.0.0.51) through the PPTP connection and then to the internet. What I did are: Set the gateway on PC(10.0.0.51) as 10.0.0.70 Enabled ipv4 forward on 10,0,0,70 Add the masquerade rule to iptable: iptables -t nat -A POSTROUTING -o ppp0 -s 10.0.0.51 -j MASQUERADE After that, it seems none of the traffic from 10.0.0.51 be redirected to ppp0, instead these traffic are still going through 10.0.0.1 directly. Any thoughts on it?

  Read the article

• Update/Insert With ADF Web Service Data Control

  - by shay.shmeltzer

  The Web service data control (WSDC) in ADF is a powerful feature that allows you to easily build a UI on top of WS interfaces exposed by other systems. However when you drag a WSDC to a page you usually get a set of output components where the data is shown. So how would you actually do an update operation on those values? The answer is that you need a call to another method in your WSDC that does the update - but what if you want to pass to it the actual values that you get from the get method you invoked before? Here is a demo showing how to do that: The two tricks that are shown here are: Changing the properties of items in the DC to be updateable - this gives you inputText fields instead of outputText fields. And passing the currentRow.dataProvider to the update method (and choosing the right iterator for this).

  Read the article

• Forcing a Service to Restart at Boot

  - by pjtatlow

  So I use winbind and samba to connect to an AD domain at work, and one of my ubuntu machines has been having issues. At boot, I cannot log in as an AD user, but if I log in as the local user and do a sudo service winbind restart it works fine. Yes, winbind does start at boot, although for some reason incorrectly I think. I can't tell anything from the logs, and I'm just wondering how to force winbind to restart after it starts the first time, at boot. Thanks!

  Read the article

• Use of Service Bus in a Pub-Sub Engine

  - by JoseK

  In one of our projects, we've built a Publisher - Subscriber Engine on Oracle Service Bus. The functionality being a series of events are published and subscribers (JMS queues) receive these whenever a new event is published. We are facing some technical issues now, performance-wise and hence an architectural review is underway. Now for my questions: Architecturally the ESB has to publish events into a DB and read from the DB which users wish to be notified, then push the event onto their respective queues. There is a high amount of DB interaction and the question is whether ESB should be having such high amount of interaction with the DB in the first place? Or should there have been some alternate component responsible for doing this. Alternately is there any non-DB approach in which we can store the events and subscribers? Where else can this application data be held within the ESB context?

  Read the article

• not start the cron (scheduler) service

  - by user74730

  A have problem witch Natty Narwhal uname -r 2.6.38-15-generic. After update cron is not starting. ps aux | grep [c]ron -- none :( ls -la /etc/ | grep crontab -rw-r--r-- 1 root root 724 2011-01-05 13:22 crontab apt-get install --reinstall cron && dpkg --configure -a && service cron restart ps aux | grep [c]ron -- none :( chkconfig --list|grep cron anacron 0:off 1:off 2:on 3:on 4:on 5:on 6:off cron 0:off 1:off 2:on 3:on 4:on 5:on 6:off How-to repair this problem?

  Read the article

• Is it possible to set a VPN through Tor? and have functionality for Software Updates?

  - by moazhmi

  Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

  Read the article

• How to setup DNS server behind a VPN

  - by Brian

  I want to host some websites behind a VPN and I need some help with the finer points of the configuration. Thus far I've settled on OpenVPN + Bind9 and I want to configure the domains like this: External DNS mail.example.com www.example.com vpn.example.com I want to be able to connect to the vpn using 'vpn.example.com'. Once connected I then want to be able to resolve anything which is '*.vpn.example.com' with the DNS server sitting behind the VPN. I know that OpenVPN can push DNS servers to clients when they connect. I am having trouble though with the DNS config, both internal and external. I've gone through a few tutorials etc. and tried to reason about it myself but I'm not getting anywhere. So my main question would be does the above configuration make sense? If so, any general pointers or examples would be greatly appreciated. Here's what I've tried so far based on this tutorial (I've redacted my domain with example.com). When I try the tests with dig at the end to check the resolution is working it fails. db.vpn.example.com $TTL 15m vpn.example.com. IN SOA ns.vpn.example.com. [email protected]. ( 2009010910 ;serial 900 ;refresh 900 ;retry 900 ;expire 900 ;minimum TTL ) vpn.example.com. IN NS ns.vpn.example.com. ns IN A 192.168.0.2 test IN A 192.168.0.2

  Read the article

• Problem with Windows Service and network printers.

  - by Mohammadreza

  I have a Windows Service application that every now and then should print some documents. As far as I know, to print those documents, my service must be run with a user account other than Local Service or Network Service. So i have created a user account and added that to the Administrators group and ran the service with it. With locally installed printers, I don't have any problems because those printers are automatically installed for all accounts. To be able to print with the network printers, I have created another application that syncs the installed printers of the currently logged in user with the user account that my service uses with the rundll32.exe printui.dll,PrintUIEntry command. In Vista and Windows7 I don't have any problems with the syncing of the printers because every time that a printer should be installed the authentication window will open and it asks for the appropriate user account to install that printer (The service user account is not created on the network printers computers) but in XP a find dialog with the "Connecting to {printername}" caption will appear and stops responding, or sometimes it installs the printer but every time service tries to print, a Win32Exception with "A StartDocPrinter call was not issued" message will throw and in the user account that runs the sync application a duplicate printer will be shown and I couldn't delete those printers unless with force (using registry). Am I doing the right thing for printing documents with Windows Services at all? If yes, how can I solve the above-mentioned problem? And if not, what the heck should I do? Thanks.

  Read the article

• Nagios service active only when other service is failing

  - by Laimoncijus

  Is is possible to define service to be active only the times while other service is failing? Consider following example: 2 hosts available: HostA (primary) and HostB (backup). Nagios service, which monitors amount of active connections to the host: gives OK when amount of connections to host 0 gives FAILURE when amount of connections to host = 0 If setup nagios service to monitor both hosts: HostA and HostB - it will give me OK for HostA (while it is primary and all connections normally goes to it) and FAIL for HostB (while it is backup and will receive no connections while HostA is alive). Can I make the nagios service for HostB somehow depend on sevice of HostA and give no failures (or maybe be inactive) up to the moment the service of HostA starts failing?

  Read the article

• Specifying a file name for the FTP and File based transports in OSB

  - by [email protected]

  A common question I receive is how to incorporate a variable value into a file name when using the FTP, SFTP, or File transports in Oracle Service Bus.  For example, if one of the fields in a message being put down to a file by the File transport is an order number variable, then how can you make the order number become part of the file name?  Another example might be if you want to specify the date in the file name.  The transport configuration wizard in OSB does not have an option to allow for this, other than allowing you to specify a static prefix of suffix variable.

  Read the article

• How can Bonjour be setup to function over a VPN connection using Mac OS X — Mountain Lion Server?

  - by Ben Coppock

  I purchased Mountain Lion Server for our office thinking that Bonjour would automatically enable any computers connected via VPN to see all computers and applications (such as Bento) running on the office network. The hope was that those of us working at home would feel just like we were in the office, with all network services working transparently over the VPN connection. However, I see that Bonjour (aka mDNS) is not enabled to work over the VPN by default. Can I configure Mountain Lion Server to automatically pass Bonjour traffic over the VPN? Is there any reason not to do this?

  Read the article

• How do I send traffic from my Mac's wifi to my VPN client?

  - by Heath Borders

  I need to connect my Android to a Juniper VPN. Unfortunately, Juniper doesn't support Android on our VPN version. We've already put in a feature request for it, but we have no idea how long it will take to be complete. Right now, I connect to the Juniper VPN with a Juniper Mac OSX VPN client that uses Java to install kernel extensions to start and stop the VPN. Thus, I can't use the Network panel in System Preferences to create a VPN device, which means it won't show up in the 'Sharing' panel's Internet Sharing Share your connection from: menu, as suggested here. I used newproc.d to see what /usr/libexec/InternetSharing did when it ran, and it runs the following processes: 2013 Nov 1 00:26:54 5565 <1> 64b /usr/libexec/launchdadd 2013 Nov 1 00:26:55 5566 <1> 64b /usr/libexec/InternetSharing 2013 Nov 1 00:26:56 5568 <5566> 64b natpmpd -d -y bridge100 en0 2013 Nov 1 00:26:56 5569 <1> 64b /usr/libexec/pfd -d 2013 Nov 1 00:26:56 5567 <5566> 64b bootpd -d -P My Juniper VPN client creates the following devices (output of ifconfig): jnc0: flags=841<UP,RUNNING,SIMPLEX> mtu 1400 inet 10.61.9.61 netmask 0xffffffff open (pid 920) jnc1: flags=841<UP,RUNNING,SIMPLEX> mtu 1450 closed So, it seems like I should just be able to do this and have everything work: sudo killall -9 natpmpd sudo /usr/libexec/natpmpd -y bridge100 jnc0 My android connected fine and could hit public internet sites, but it couldn't hit private VPN sites. I assume this is because I need to change the routes that /usr/libexec/InternetSharing sets up. This is the output from sudo pfctl -s all before starting Internet Sharing: No ALTQ support in kernel ALTQ related functions disabled TRANSLATION RULES: nat-anchor "com.apple/*" all rdr-anchor "com.apple/*" all FILTER RULES: scrub-anchor "com.apple/*" all fragment reassemble anchor "com.apple/*" all DUMMYNET RULES: dummynet-anchor "com.apple/*" all INFO: Status: Disabled for 0 days 00:11:02 Debug: Urgent State Table Total Rate current entries 0 searches 22875 34.6/s inserts 1558 2.4/s removals 1558 2.4/s Counters match 2005 3.0/s bad-offset 0 0.0/s fragment 0 0.0/s short 0 0.0/s normalize 0 0.0/s memory 0 0.0/s bad-timestamp 0 0.0/s congestion 0 0.0/s ip-option 12 0.0/s proto-cksum 0 0.0/s state-mismatch 1 0.0/s state-insert 0 0.0/s state-limit 0 0.0/s src-limit 0 0.0/s synproxy 0 0.0/s dummynet 0 0.0/s TIMEOUTS: tcp.first 120s tcp.opening 30s tcp.established 86400s tcp.closing 900s tcp.finwait 45s tcp.closed 90s tcp.tsdiff 60s udp.first 60s udp.single 30s udp.multiple 120s icmp.first 20s icmp.error 10s grev1.first 120s grev1.initiating 30s grev1.estblished 1800s esp.first 120s esp.estblished 900s other.first 60s other.single 30s other.multiple 120s frag 30s interval 10s adaptive.start 6000 states adaptive.end 12000 states src.track 0s LIMITS: states hard limit 10000 app-states hard limit 10000 src-nodes hard limit 10000 frags hard limit 5000 tables hard limit 1000 table-entries hard limit 200000 OS FINGERPRINTS: 696 fingerprints loaded This is the output from sudo pfctl -s all after starting Internet Sharing: No ALTQ support in kernel ALTQ related functions disabled TRANSLATION RULES: nat-anchor "com.apple/*" all nat-anchor "com.apple.internet-sharing" all rdr-anchor "com.apple/*" all rdr-anchor "com.apple.internet-sharing" all FILTER RULES: scrub-anchor "com.apple/*" all fragment reassemble scrub-anchor "com.apple.internet-sharing" all fragment reassemble anchor "com.apple/*" all anchor "com.apple.internet-sharing" all DUMMYNET RULES: dummynet-anchor "com.apple/*" all STATES: ALL tcp 10.0.1.32:50593 -> 74.125.225.113:443 SYN_SENT:CLOSED ALL udp 10.0.1.32:61534 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL udp 10.0.1.32:55433 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL udp 10.0.1.32:64041 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL tcp 10.0.1.32:50619 -> 74.125.225.131:443 SYN_SENT:CLOSED INFO: Status: Enabled for 0 days 00:00:01 Debug: Urgent State Table Total Rate current entries 5 searches 22886 22886.0/s inserts 1563 1563.0/s removals 1558 1558.0/s Counters match 2010 2010.0/s bad-offset 0 0.0/s fragment 0 0.0/s short 0 0.0/s normalize 0 0.0/s memory 0 0.0/s bad-timestamp 0 0.0/s congestion 0 0.0/s ip-option 12 12.0/s proto-cksum 0 0.0/s state-mismatch 1 1.0/s state-insert 0 0.0/s state-limit 0 0.0/s src-limit 0 0.0/s synproxy 0 0.0/s dummynet 0 0.0/s TIMEOUTS: tcp.first 120s tcp.opening 30s tcp.established 86400s tcp.closing 900s tcp.finwait 45s tcp.closed 90s tcp.tsdiff 60s udp.first 60s udp.single 30s udp.multiple 120s icmp.first 20s icmp.error 10s grev1.first 120s grev1.initiating 30s grev1.estblished 1800s esp.first 120s esp.estblished 900s other.first 60s other.single 30s other.multiple 120s frag 30s interval 10s adaptive.start 6000 states adaptive.end 12000 states src.track 0s LIMITS: states hard limit 10000 app-states hard limit 10000 src-nodes hard limit 10000 frags hard limit 5000 tables hard limit 1000 table-entries hard limit 200000 TABLES: OS FINGERPRINTS: 696 fingerprints loaded It looks like I need to change the pf settings that /usr/libexec/InternetSharing set up, but I have no idea how to do that.

  Read the article

• Debugging Visual Studio 2010 Unit Test and WCF Service in one IDE instance

  - by Dr.HappyPants

  I have created a WCF service in Visual Studio 2010 along with some supporting assemblies. I have also created a test project which contains multiple unit tests for the service and the supporting assemblies. Right now I have them all in one solution with the Test project having a service reference (http) to the WCF service. If I debug the WCF service and select "Run checked tests" in a Test List I created, I can debug the WCF service without a problem. Note: I cannot select Debug Checked Tests while debugging the WCF service. (Because the IDE is already debugging?) If I open the Test project in another instance of VS 2010, debug the WCF service and then select "Debug Checked Tests" - I can debug both my tests and the WCF service. However - I would like to (and my question is) be able to debug my tests and my service in a single IDE. Is this possible?

  Read the article

• Can I easily use a VPN to duplicate SSH Tunneling functionality?

  - by Steve V.

  Right now, when I want to use an unsecured wireless connection with my (Linux) laptop, I secure my connection using a variation of the method provided here. However, to the best of my knowledge, the (non-jailbroken) iPad does not allow applications to tunnel traffic through local ports. However, it does seem to allow certain VPN traffic. I have never set up, or even used, a VPN before. I'm looking for confirmation that I'm not barking up the wrong tree before I invest significant effort into setting up my own VPN server. If I want to secure my wireless iPad traffic over an unsecure wireless connection, would I be on the right track by looking at a VPN?

  Read the article

• VPN Sonicwall 190 with MAC OS 10.6.1?

  - by matthewb

  Has anyone been able to vpn to a sonicwall 190, using a free or cheap VPN client? I've tried VPN Tracker 6 and it works but don't want to spend $129+

  Read the article

• VPN running in vmware vm, is there any way to get the host to share that tunnel?

  - by Marco

  I'm running WinXP in VMWare Fusion hosted by MAC OS X 10.5. There's no mac client for the vpn I need to use so I'm going through windows. The vpn runs fine in the vm. Is there a way I can get my host mac connection to piggyback off this vpn so I can access the network through the mac? I can provide more info, so let me know what would be helpful.

  Read the article

• How do I set up a connection to a Stonegate VPN in Ubuntu?

  - by Igor Zinov'yev

  I'm relatively new to the topic, so please help me. I have a single VPN connection plugin installed, and it's vpnc. As far as I can see, it's not the thing I need to establish a VPN connection to a Stonegate VPN gateway. Is there a plugin for that gateway? What software should I use, or at least where do I start reading? Thanks in advance!

  Read the article

• High availability for Windows Service under Windows Server 2003

  - by empi

  Hi. I have a following situation: I need to deploy a windows service that listens for incoming request on tcp port (basically WCF service). I have a High Availability requirement - the service must be deployed on two servers and if the service stops (only the service, not the whole server) on one server, all the requests must be redirected to the second one. For me it looks like a basic failover scenario. How can I achieve this on Windows Server 2003? Should I use Microsoft Cluster Service or Network Load Balancing? The important part is that the process of swapping the servers should not concern the clients (the client must see only single address / single host or domain name). Thanks in advance for help.

  Read the article

• Something in the world of Firewall Hosted SSL VPN's

  - by AreYouSerious

  I run a Physical firewall at my residence. Call me paranoid, but I appreciate the added security. I have been working to get the VPN to work properly, but had until today not managed this. I worked with ensuring that the VPN configurations were correct, that the port filters were correct,  I could connect to the Firewall GUI, but never to the VPN. Turns out that in W7, if you add a key, it suddenly works.Computer\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SecurityProviders\SCHANNELAdd DWORD(32-bit) - SendExtraRecord --> value 2 and voila, suddenly your presented with the login screen. I won't mention the specific vendor, as they don't have this listed in their fixes... but there are several venders where this is an issue. So, if you are having an issue connecting to an SSL VPN (web vpn) this might just be the solution that you need.

  Read the article

• IP Phone over VPN - one way calls unless default route?

  - by dannymcc

  I have come across a strange problem with our VPN and BCM 50 (Nortel/Avaya) phone system. As you can tell by my other questions I have been doing some work on setting a VPN up from one location to another and it's all working well. With one exception. We have an IP phone that is connected at the remote location, straight to a router which has a VPN tunnel to our main practice. The phone works mostly, but every few calls it turns into a one way call. As in, the caller (from the remote phone) can't hear the receiver- but the receiver can hear the caller. This is fixed by setting the VPN tunnel to be the default route for all traffic. The problem with fixing it that way is that all traffic then goes through the tunnel which slows internet access etc. down considerably. The router is set to send the following over the VPN: 192.168.1.0/24 192.168.2.0/24 192.168.4.0/24 The IP of the remote location is: 192.168.3.0/24 The remote router (where the phone is) is a Draytek 2830n, and the local router (at the main practice) is a Draytek 2820. We are using an IPSec tunnel with AES encryption <- as a result of a previous answer pointing to the incompatibility in the hardware encryption. Any advice would be appreciated!

  Read the article

• Windows service running under network credentials doesn't autostart

  - by David Alpert

  I have a Subversion Server running as a resident service on a Windows XP Pro machine. That service needs to access a secure network fileshare, so I used the Services-Properties-Log On tab to tell the service to run as a user who has access to the target fileshare. That works out fine until the machine restarts, when the service fails to autostart. I am able to start it manually by logging in, going back to that Services-Properties-Log On tab and reconfiming the explicit credentials. Do I have to manually start this service under alternate credentials every time the machine reboots? Is there something else I can do to make sure that my Subversion server service autostarts with proper access to authenticate against this network share?

  Read the article

• Symbol of VPNanytime is not shown anymore after upgrading from Ubuntu 11.04 to 11.10

  - by Aufwind

  Usually when I start VPN anytime (by calling a certain url in firefox) in Ubuntu 11.10 I saw a little "green symbol with a yellow lock in front of it" for the VPN anytime client near the clock. If I wanted to quit the VPN connection I just clicked on this symbol and hit logout/quit. Today I upgraded to Ubuntu 11.10 and the VPN connection works here fine too. But the symbol near the clock is not shown anymore. Is this a bug or do I have to set this up manually? And is there a way to quit the client perhaps by terminal? Currently I just do a restart, when I want the vpn connection terminated and that's kind uncomfortable. :-) Thanks for any suggestions!

  Read the article

• Does a VPN requirement kill the concept of having a Web Application in the Cloud?

  - by Christian

  Recently I posted a question in SO, but so far I got no answers. I wonder if I'm asking the wrong question. This is the problem: We need to design an application which offers a public http web service, but at the same time it must consume some services through a VPN connection from other existing company. There is no other alternative but to use a VPN connection to access those services. We want to host our application in some cloud infrastructure like Heroku or Amazon EC2. But there is no direct way to access the VPN services of the other company from there. The solution I'm thinking, but I don't like is to have a different server to expose the services from that VPN. But this will require the setup of another server which I prefer to avoid. In the case this is the solution, can I use an Amazon EC2 instance to connect to a VPN? This is what I was thinking, is it correct? I don't have experience using VPNs, tunnels or those kind of networking stuff. I will really appreciate if you can propose me an alternative solution, or just give me a comment.

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >