Search Results

Search found 16499 results on 660 pages for 'off rhoden'.

Page 342/660 | < Previous Page | 338 339 340 341 342 343 344 345 346 347 348 349  | Next Page >

• Ubuntu 12.04 Fails to Boot after Reboot

  - by Joe

  I have installed Ubuntu 12.04 on several Dell c6220 servers. The install was successful and all hardware is recognized. The problem that I am running into is that when issuing the reboot command or when pressing ctrl-alt-del, the server shuts down, but never comes back up. Instead, the fan revs up to full speed and stays that way until I power the server down. Once the server has been powered down via the power button, Ubuntu will boot just fine -- until the next reboot. I have found that by rebooting the server via the DRAC web interface will reboot the server correctly. I have also found that this problem does not exist with CentOS -- I can press ctrl-alt-del all day long and it always comes back up. I've tried several kernel parameters such as: reboot=bios reboot=pci reboot=acpi reboot=cold acpi=off noapic Nothing seems to work. I have also tried upgrading to kernel 3.4, but no change there, either. Has anyone run into a similar problem or any pointers on troubleshooting? Thanks, Joe

  Read the article

• My WD Caviar Green SATA HDD cannot be detected

  - by obhasha

  I have a WD 2TB Caviar Green SATA HDD. I used it as an external hard drive formatted to FAT32. The main purpose was to store my PS3 games. It worked fine and all of a sudden my PS3 stopped detecting it. I tried connecting it to my pc and the same result. I took it off from the enclosure and plugged it directly to my PC and used the BIOS setup. The BIOS setup detects my HDD but it says it's 0.0MB!!! I also tried the WD Data Lifeguard Diagnostic tool and it wasn't much of use because the drive is not picking up by windows at all. Is my HDD dead? Is it beyond repair?

  Read the article

• Calculating the number of occasions with a set period sumproduct function

  - by user158056

  =SUMPRODUCT((F16:F274=("A")) *(F17:F275<>("A"))) +SUMPRODUCT((F16:F274=("AH")) *(F17:F275<>("AH"))) +SUMPRODUCT((F16:F274=("AU")) *(F17:F275<>("AU"))) +SUMPRODUCT((F16:F274=("AHU"))*(F17:F275<>("AHU"))) I am using the above formula to add the number of occasions sickness occurs using the following as a key. It works fine until you get say an A and a AH in the same sickness period. Instead of reporting just one occasion off it reports two. Is there a way I can separate this? Absence A Absence 1/2 AH Absence Unpaid AU Absence 1/2 Unpaid AHU

  Read the article

• How do I stop color changes when quitting vi from a terminal emulator?

  - by Michael Warhol

  I have a problem with colors when using vi under Ubuntu 12.04. I'm connecting to my Ubuntu server from a PC, using PowerTerm terminal emulation software. I have PowerTerm set up to display black text on a grey background. When I connect to the Ubuntu box, the screen is fine. When I open a file with vi, the screen is fine. The text is black on a gray background, which is normal for my PowerTerm setup. However, if the file is less than a full screen long, the remainder of the screen is a black background. When I quit vi, the entire background turns black, and the text becomes white. I have to do a Terminal Reset to restore my normal text and background colors. What I want is for there to be no change at all when I use vi. The text should be black and the background grey. I have another server loaded with RedHat 9, and that acts normally; colors don’t change when using vi. Here is my .vimrc file: set compatible syntax off let g:loaded_matchparen=1 set nocp set noincsearch set nohlsearch set noshowmatch set bg=dark I've tried set bg=dark and set bg=light. It makes no difference. Is there some other set command that would clear this up for me, or some TERM setting (my TERM is set to linux)?

  Read the article

• postfix: force server to send mail outside of localhost

  - by LoneWolfPR

  I have a php file that sends mail using the mail() function. The problem is one of the forms sends to a domain that is registerred on my server while having the mail handled on a different server. Postfix looks locally only. When it doesn't find the email address is rejects the message. How can I configure postfix to send mail to all domains through the internet and not locally? Update Ok. So it wasn't a postfix issue at all. I simply needed to turn off mail to that domain from the command line. For anyone that needs that command it is (at least on my system): /usr/local/psa/bin/domain --update example.com -mail_service false

  Read the article

• plesk + high POP3/IMAP traffic, how to check details?

  - by Danzzz

  Please check this image, it's a screenshot from plesk 10 of 1 domains mail traffic: This domain has about 1GB POP3/IMAP (OUT) traffic each day. I know that this is not normal because I know the owner and how he's using his mail. It's just some mails each day. Is OUT in this case incomming mails to the domain owner? or is it OUTgoing imap traffic? I have about 30 domains on this machine, but this one is the only one making so much traffic. How can I check whats happening there? Can I check which email adress makes the most of this traffic? Can I try to swich off Imap for just this domain?

  Read the article

• Postfix configuration w.r.t. port 25

  - by Monkey Boson

  After a considerable amount of research, I have configured my postfix server to use dovecot to accept SMTPS connections over port 465 and everything works swimmingly. Unfortunately, I forgot that, unless I listen to port 25, I'm not going to receive any e-mail from the net. I'm hoping somebody knows off the top of their head how to open up port 25 on Postfix for anonymous users, but disallow relaying and any other bad things on that port. And to leave the port 465 the way it is. As to my current configuration, I changed the master.cf file: smtps inet n - n - - smtpd and the main.cf file: # Use our SSL certificates smtpd_tls_cert_file = .....cer smtpd_tls_key_file = .....key smtpd_tls_security_level = may # Use Dovecot for SASL authentication smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_sasl_authenticated, reject_unauth_destination Any help is appreciated!

  Read the article

• Credentials needed for BT line on Netgear router

  - by Bali C

  I have recently bought a new Netgear router to replace my current BTHomeHub as it doesn't support wireless. I did buy a WAP but figured it would be easier to use a router with wireless built in. (It's a modem/router combo). I have got as far as setting up the router on the web interface, but then it asks for a username and password to connect to the net, I can only assume this is for the phone line? I have tried some passwords I could find written down but they don't work, the internet light comes on and then when the creds fail it goes off. I have been on the homehubs web interface and been through all the settings it has to find the credentials it is using which obviously work, but no joy. Is there anything obvious I am missing, or is there a way I can retrieve my settings from my existing router? Any pointers will be very appreciated.

  Read the article

• Tools/Tips to reduce the files/directories in C: which is SSD on Windows 7.

  - by prosseek

  I bought a SSD to install it as C: drive on Windows 7. As the SSD size is relatively small, I need to come up with an idea to reduce the files/directories in C:. What I found is as follows. Run WinDirStat to check how the C: is used. Remove the hibernate file (if you don't use it) powercfg –h off http://helpdeskgeek.com/windows-7/windows-7-delete-hibernation-file-hiberfil-sys/ Symbolic link files and directories to different drive. I'm not sure if this is safe way to go, I asked another post to ask about it. mklink /d e:\windows\installer c:\windows\installer Install software to E: directory, not C: directory. Create E:\Program Files What other tools or tips do you have?

  Read the article

• During interviews, how do I gauge a company's respect for my position?

  - by Bluu

  I'm a web developer who previously joined a software company not knowing their value and respect went to big data analysis, not their website. Sure, they needed a public-facing website, but I eventually found that the most exciting, valued projects there went to data teams. Realizing this, members of the web team were picked off and switched teams, making it hard for those left behind to keep up the work load, and making us look bad. At times it seemed the company culture sneered at us, wondering, "What does that team even do here?" A friend of mine had the opposite problem at another software company. All he wanted to do was crunch big numbers. However he complained that the rest of the company wouldn't shut up about developing the usability of their website. Meanwhile his analytics team languished. I've also heard of salespeople getting love at a company, while engineering as a whole is undervalued, or vice versa. As for my story, if I could have known the company was like that, I might have avoided the job in the first place. So, before I join a new company, how do I gauge its actual respect for my programming role? For its other roles? I want to avoid companies that aren't serious about my particular focus in programming, or, perhaps bigger picture, companies that don't value everybody who works there. (Note I think gauging the company's attitude toward the basic needs of its programmers is covered by these related questions.)

  Read the article

• How to limit access to Exchange 2003 Mobile Actviesync server by user?

  - by micilin

  So I was asked to set up an Exchange Activesync mobile gateway. That's done. It's a separat eExchange 2003 front-end server configured for SSL, and I've put an off-domain ISA server in front of it. Now I'm being asked to limit which users can connect to it. By default an Exchange front-end server allows any user who has a mail account to connect to the front -end server. So I'm looking at the permissions on the various IIS sites/apps on the server, but I know that it's easy to break Exchange Front-end server perms. So I've got the following in IIS: Exadmin Exchange EchWeb Microsoft-SErver-ActiveSync MobileAdmin OMA And a couple of others that I dont think are relevant. Can I change the permissions on one of these to restrict who can connect to Activesync? As a bonus: Can I do it in a way that does not affect ordinary browser based Exchange Access? Thanks in Advance!!

  Read the article

• 2 DSL lines...any benefit?

  - by EJB

  I have verizon DSL in my office, I put DSL in about a year ago for $29.95 month...I added a new phone line recently and it was cheaper to actually get it bundled with DSL so now I have two DSL lines...my plan was to shut the first one off when my 1 year contract comes up (in September). A couple of times DSL has gone out on one line so I just used the other, which is a nice redundancy to have - but it doesn't happen often. (I unplugged one line and plugged in the other) Question is, is there any way to use both DSL lines together so that 1) I can increase bandwidth and effective speed might increase (is that possible?) or 2) have them both on and connected someway so that traffic on my network would just use either one, and if one went down the traffic would route automatically? If I can either increase speed by having two, or at a minimum get some automatic redundancy, I see no reason to keep both on.... Thanks!

  Read the article

• Dead-simple USB-based Windows partition cloner?

  - by OverTheRainbow

  Clonezilla is a fine open-source tool, but it requires going through several screens. Since I need to save/restore the same Windows partition, I was wondering if someone knew of a tool (open-source or not) that is easier to use and boots off a USB keydrive. Ideally, it'll save the two commands to save/restore a partition, so I just need to boot the host from the USB key, choose the command, and it'll take care of business. Are there solutions that look like this? Thank you. Edit: Here's one among other articles that shows how to tell CZ to run a script to avoid the multiple screens.

  Read the article

• Windows terminating system processes

  - by jemper

  To be sure nobody will answer me with advice on not trying to terminate critical (system) processes - I'm relatively experienced in programming and Windows in general - I'd know what I'm doing so far. So there are these processes that can't be terminated with taskkill - system processes in general. But there also is, for example my Anti Virus program that makes itself "unterminateable". How can I access and mainly terminate system processes under windows? (kill.exe by Microsoft doesn't work) How do processes like anti-virus programs protect themselves? How can you turn them off again, then?

  Read the article

• HP Deskjet 3600: Offline and won't stop blinking and won't print.

  - by George Bailey

  Using Vista and an HP Deskjet 3600 on USB connection Normally when I unplug the printer, I open the printer queue and in the title bar it says "HP Deskjet 3600 - Use Printer Offline" then the offline message will go away and it will start printing. But for some reason, the bower button light is continually blinking. (this is the only light on the machine). The printer queue says "HP Deskjet 3600 - Offline" and when I unplug it it says "HP Deskjet 3600 - Offline - Use Printer Offline". I have tried unplugging it for a few hours, also tried turning it off for a few hours. Does anybody know what the single word Offline means? Does anybody know how I can clear out the memory in the Printer? (this is my guess as to what is causing the problem)

  Read the article

• How do you import an EPS file in Inkscape?

  - by Neil

  I'm using Inkscape, and I'm trying to import an EPS file to use it as a vector and eventually save it as an SVG. This link here mentions several methods: http://www.inkscapeforum.com/viewtopic.php?f=5&t=797 But the responses aren't rated since it's a forum, so I thought I'd ask here to find the best answer. I'd prefer not to have to use some website to convert the file to a PDF first. Either way, when I import an EPS into Inkscape, or use the website to convert it to a PDF, in both cases the resulting file loses all colour and gradients, and the EPS file gets cut off on the right side. It looks like ps2pdf is clipping the file incorrectly, and Inkscape is eliminating the colour. I have these version installed in Ubuntu Lucid Linux: Inskape 0.47.0-2ubuntu2 Ghostscript 8.71.dfsg.1-0ubuntu5.3

  Read the article

• Mac firewall blocking nginx (port 80) from external side

  - by Alex Ionescu

  I installed nginx using ports and started it with sudo. Accessing the nginx welcome page from localhost works perfectly, however accessing it from an external computer fails. Doing an nmap on the computer from the outside reveals 80/tcp filtered http So clearly the mac firewall is blocking the port. I then proceed to add the nginx executable to the firewall exception list as seen in this image, however the nmap still shows up as port 80 being filtered and I'm unable to access the webpage. The exact binary that is in the list is /opt/local/sbin/nginx which to my knowledge seems correct Any ideas what I should do? Thanks! P.S. Turning the firewall off does allow me to access the website from the outside world, however that isn't an ideal solution.

  Read the article

• Twinview broken on upgrade to ubuntu 10.10

  - by mapkyca

  I have been on 9.10 for over a year on the grounds that if it ain't broke, don't fix it. However, I had a spare weekend and figured it was probably about time... I performed an upgrade to 10.4, and everything seemed to proceed smoothly, so I took the plunge and went for 10.10. Disaster. My twinview Nvidia display which had been working perfectly is now broken. On boot everything seems fine, but when X starts and the second monitor springs into life the primary winks out and switches off - almost as if its been put into an unsupported display mode. The system seems to think there's a second monitor - the nvidia logo is split across the two screens, but it can't seem to start. Things I've tried: Swapping the monitors (one is older than the other, and its definitely the port not the actual monitor) Rolling back to an old Xorg conf from prior to the upgrade Installing a non-beta driver direct from Nvidia (this seems to start both monitors but then apparently stops boot and causes the second display to 'wink'. Twinview seems non-functional, both displays are mirrors) Disabling EDID Disabling twinview, logging in and attempting to use the Nvidia config to re-detect the monitors (second monitor is falsely detected and won't go higher than 1024x768. Selecting 'apply' causes one screen to go blank and the other to display garbage) googling for about 5 hours looking for similar problems, none of the offered solutions seemed to work I'm at a loss, and it is looking very much like I'm going to have to go through a time consuming reinstall to downgrade back to the working 10.4. Any thoughts?

  Read the article

• Outlook keeps dropping 'Other Calendars'

  - by David Gard

  We run Exchnage 2010 with Outlook 2007, and we have public calendars that users are able to 'Add to favorites...' - these are then shown under 'Other Calendars' when a user clicks their 'Calendar' tab. The issue we are having is that these calendars drop off every now and again. Looking under 'Public Folders - Favorites', I can see that the calendars are there, but Outlook doesn't seem to know that they are calendars any more. Simply clicking on one of them to open it changes the icon to that of a 'Folder containing calendar items' for each of the favorite items, and closing and reopening Outlook gets them back under 'Other Calendars' My question is this - how can I make Outlook stop forgetting that these public folders are calendars? Thanks.

  Read the article

• Windows Server 2008 R2 - Can't connect RDP over the Internet

  - by Jonathan DeMarks

  I have two networks: Domain and Public, Domain is a VPN connection and Public is the local connection to the network. This is not a domain controller or a DNS/DHCP server. I can connect via RDP from the local network (192.168.1.), from the VPN network (10.1.2.), and from the VPN network over the internet. I cannot connect from the internet (anywhere besides where the server is VPN'd) Wireshark indicates that the server is getting packets, and the audit log is indicating that the packets are being dropped. Advanced Firewall has explicit options to allow RDP, and has no deny policies. I have also tried turning Firewall off completely to no avail. I'm really lost on this one.

  Read the article

• Identify an instance of Google Chrome by PID

  - by Laramie

  While working I generally need around 40 windows open at a time and run 100-200 processes. When memory constraints become an issue, I start picking off the processes that are the most resource intensive and disposable. Often these are chrome.exe. It would be helpful to be able to match a particularly memory-hungry instance of chrome to it's PID so I can selectively close it. That is, if I knew what the page title it is currently open to, I could choose whether it lives or dies. I've tried Process Explorer to no avail. Any ideas?

  Read the article

• process running on login: can't find in AD or login batch scripts

  - by tombull89

  Hallo, I'm trying to deploy some classroom control software (NetSupport School) to some of the machines on our network but for some reason when you log off and restart the computer any user who logs on ends up re-installing the software while logging on. I spent two hours on the phone to the complanys support and we eventually nailed it down to most likely a setting in Active Directory or in the login.bat (drive mapping and settings) but we can't find anything in those that would say "run this installer at logon". Is there anywhere else on the system that would set something like this? Server 2003/XP. Ta!

  Read the article

• setting up a second monitor in centos

  - by Rob

  I have CentOS installed on my laptop. I hooked up my TV via VGA and it works, just not as I'd like it to. The left side (on the tv) is cut off, like the image is justified too far left. I want it to be centered, but I also want to use a different resolution. You see, I use a netbook, and thus my laptop screen is tiny, meaning some things cant fit in the same window without scrolling. I want my TV to fix that for me.

  Read the article

• Windows XP Activation Issues

  - by David

  Related to my older question: Get xp product key from boot Thanks for the help on that one. So, in the end, i couldn't get into my harddrive because i didn't have the available hardware to hook it up to another computer to get the old activation key. So, instead, i entered another activation key (i know, naughty) in hopes that there would be a way to retrieve the old one, restore point or something afterwords. What legal ways can I get xp re-activated after a repair when I don't have any record of my activation key? for those who think im just trying to crack it, your wrong: Got a virus, which stopped me from getting into windows Got AVG Anti Virus, which stopped me from getting into safe mode Got a 2 year old, who decided to rip-off and chew my activation sticker on my computer (nice one). Repaired windows installation thinking i wouldn't be asked to re-enter the activation key, to find that i was.

  Read the article

• DVI problem with LG L204WT

  - by Holgerwa

  I have a LG L204WT which has VGA and DVI connectors. Until recently, I have used the monitor via VGA, but now I have upgraded the graphics board and switched to DVI. The problem is that each time after the computer starts, the monitor either doesn't show anything (black screen, but doesn't go into standby) or the picture is distorted. I then switch the monitor off and on several times, and at some point it starts correctly and then I can work as usual. This only happens on startup. It is one out of 3 monitors, the other two work fine. It seems to me as if the monitor is not able to synchronize on the DVI signal and either shows a distorted picture or nothing at all. There are no settings in the monitor setup that would change anything. What could be the problem?

  Read the article

< Previous Page | 338 339 340 341 342 343 344 345 346 347 348 349  | Next Page >