Search Results

Search found 11003 results on 441 pages for 'usb storage'.

Page 344/441 | < Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >

  • Centrino Wireless-N 1000 takes forever to connect and keeps asking for password

    - by waclock
    A few days ago I started having this problem. When I tried to connect to any WiFi Connection it would stay connecting forever, and after a minute or so it would ask me for the password again. The strange thing is that this happened out of nowhere, I did not install any new drivers or anything like that. After this happened I decided to uninstall ubuntu and install it again ("inside windows") but the problem is still there. Any suggestions would be greatly appreciated. 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:aa:e4:7d size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:50 ioport:4000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:09:9c:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:c4500000-c4501fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.2 logical name: eth1 serial: ee:85:2f:7d:80:96 capabilities: ethernet physical configuration: broadcast=yes driver=ipheth ip=172.20.10.2 link=yes multicast=yes

    Read the article

  • Are there Know issues with Ubuntu 11 and socket 1155? acpi=off

    - by James
    Since building my new system I cant get Ubuntu (or any other flavor of Linux) to "run" properly. To boot the live cd I have to "F6" and turn off acpi or the screen halts at a black screen with "boot stuff" written above the blinking curser. When installed I can only boot if I enter repair mode from Grub menu then once in repair mode I choose Boot Normally and it boots to the desktop. Once on the desktop I can "click" (with the mouse) only on one thing...like firefox or "desktop appearance" and the mouse no longer "clicks" on anything else ...its like the computer freezes but the mouse still moves. I end up using the reset button to restart the computer. I was able to update when prompted to do so....but at the end of the update I could not "click" the "finish" and had to use the manual reset button. I have run Ubuntu since v 8... My system specs are: intel i7 2600k ...Graphics disabled in bios... Asus p8z68-v pro.... 16G Kingston HyperX.... 2 EVGA GTX 570 in SLI.... Mouse is a simple Logitech usb Wireless. Ubuntu installed on secondary sata drive.

    Read the article

  • TCO Comparison: Oracle Exadata vs IBM P-Series

    - by Javier Puerta
    Cost Comparison for Business Decision-makersOracle Exadata Database Machine vs. IBM Power SystemsHow to Weigh a Purchase DecisionOctober 2012 Download full report here In this research-based  white paper conducted at the request of Oracle, The FactPoint Group compares the cost of ownership of the Oracle Exadata engineered system to a traditional build-your-own (BYO) solution, in this case an IBM Power 770 (P770) with SAN storage.  The IBM P770 was chosen given it is IBM’s current most popular model, based on FactPoint primary and secondary research and IBM claims, and because at least one of the interviewed customers had specifically migrated from a P770 to Exadata, affording us a more specific data point for comparison. This research found that Oracle Exadata: Can be deployed more quickly and easily requiring 59% fewer man-hours than a traditional IBM Power Systems solution. Delivers dramatically higher performance typically up to 12X improvement, as described by customers, over their prior solution.  Requires 40% fewer systems administrator hours to maintain and operate annually, including quicker support calls because of less finger-pointing and faster service with a single vendor.  Will become even easier to operate over time as users become more proficient and organize around the benefits of integrated infrastructure. Supplies a highly available, highly scalable and robust solution that results in reserve capacity that make Exadata easier for IT to operate because IT administrators can manage proactively, not reactively.  Overall, Exadata operations and maintenance keep IT administrators from “living on the edge.”  And it’s pre-engineered for long-term growth. Finally, compared to IBM Power Systems hardware, Exadata is a bargain from a total cost of ownership perspective:  Over three years, the IBM hardware running Oracle Database cost 31% more in TCO than Exadata.

    Read the article

  • geomipmapping using displacement mapping (and glVertexAttribDivisor)

    - by Will
    I wake up with a clear vision, but sadly my laptop card doesn't do displacement mapping nor glVertexAttribDivisor so I can't test it out; I'm left sharing here: With geomipmapping, the grid at any factor is transposable - if you pass in an offset - say as a uniform - you can reuse the same vertex and index array again and again. If you also pass in the offset into the heightmap as a uniform, the vertex shader can do displacement mapping. If the displacement map is mipmapped, you get the advantages of trilinear filtering for distant maps. And, if the scenery is closer, rather than exposing that the you have a world made out of quads, you can use your transposable grid vertex array and indices to do vertex-shader interpolation (fancy splines) to do super-smooth infinite zoom? So I have some questions: does it work? In theory, in practice? does anyone do it? Does this technique have a name? Papers, demos, anything I can look at? does glVertexAttribDivisor mean that you can have a single glMultiDrawElementsEXT or similar approach to draw all your terrain tiles in one call rather than setting up the uniforms and emitting each tile? Would this offer any noticeable gains? does a heightmap that is GL_LUMINANCE take just one byte per pixel(=vertex)? (On mainstream cards, obviously. Does storage vary in practice?) Does going to the effort of reusing the same vertices and indices mean that you can basically fill the GPU RAM with heightmap and not a lot else, giving you either bigger landscapes or more detailed landscapes/meshes for the same bang? is mipmapping the displacement map going to work? On future cards? Is it going to introduce unsurmountable inaccuracies if it is enabled?

    Read the article

  • How do I prevent my filesystems from being mounted read-only after suspending?

    - by Chas. Owens
    I have Ubuntu 12.04 installed on an SDHC card (only one ext2 partition, no swap). When I suspend using pm-suspend, my root filesystem is mounted read-only. I am currently "fixing" this with the following file: /etc/pm/sleep.d/99_make_disk_rw: #!/bin/sh mount -o remount,rw / But the disk is marked as needing an fsck on reboot. How can I prevent the filesystem from being mounted read-only or whatever is going wrong here. Update: It looks like it is getting mounted read-only because an error occurred. I have changed the mount options for / in /etc/fstab to noatime,nodiratime,errors=continue and it no longer mounts the SDHC card as read-only after it resumes. So the problem is happening when it suspends, not when it resumes as I had thought. I checked /sys/bus/usb/devices/1-4/power/persist and it is set to 1. So the SDHC card shouldn't appear disconnected to the OS (or more accurately it should recover from the disconnection without error). Here seems to be the relevant section of the syslog Sep 10 10:34:23 iubit kernel: [ 748.246226] sd 4:0:0:0: [sdb] Media Changed Sep 10 10:34:23 iubit kernel: [ 748.246234] sd 4:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Sep 10 10:34:23 iubit kernel: [ 748.246243] sd 4:0:0:0: [sdb] Sense Key : Unit Attention [current] Sep 10 10:34:23 iubit kernel: [ 748.246253] Info fld=0x0 Sep 10 10:34:23 iubit kernel: [ 748.246258] sd 4:0:0:0: [sdb] Add. Sense: Not ready to ready change, medium may have changed Sep 10 10:34:23 iubit kernel: [ 748.246271] sd 4:0:0:0: [sdb] CDB: Read(10): 28 00 00 5d 3e f0 00 00 08 00 Sep 10 10:34:23 iubit kernel: [ 748.246291] end_request: I/O error, dev sdb, sector 6110960 Sep 10 10:34:23 iubit kernel: [ 748.247027] EXT2-fs (sdb1): error: ext2_fsync: detected IO error when writing metadata buffers Sep 10 10:34:23 iubit anacron[6954]: Anacron 2.3 started on 2012-09-10 Sep 10 10:34:23 iubit anacron[6954]: Normal exit (0 jobs run) Sep 10 10:34:24 iubit laptop-mode: Laptop mode Sep 10 10:34:24 iubit laptop-mode: enabled, not active Sep 10 10:34:24 iubit kernel: [ 749.055376] sd 4:0:0:0: [sdb] No Caching mode page present Sep 10 10:34:24 iubit kernel: [ 749.055387] sd 4:0:0:0: [sdb] Assuming drive cache: write through Sep 10 10:34:25 iubit anacron[7555]: Anacron 2.3 started on 2012-09-10 Sep 10 10:34:25 iubit anacron[7555]: Normal exit (0 jobs run) Sep 10 10:34:31 iubit kernel: [ 756.090861] EXT2-fs (sdb1): previous I/O error to superblock detected

    Read the article

  • CodePlex Daily Summary for Friday, October 12, 2012

    CodePlex Daily Summary for Friday, October 12, 2012Popular ReleasesHyperCrunch Druid: HyperCrunch Druid 1.0.2102: For all documentation and feedback, visit http://druid.hypercrunch.com.GoogleMap Control: GoogleMap Control 6.1: Some important bug fixes and couple of new features were added. There are no major changes to the sample website. Source code could be downloaded from the Source Code section selecting branch release-6.1. Thus just builds of GoogleMap Control are issued here in this release. NuGet Package GoogleMap Control 6.1 NuGet Package FeaturesBounds property to provide ability to create a map by center and bounds as well; Setting in markup <artem:GoogleMap ID="GoogleMap1" runat="server" MapType="HY...Bundle Transformer - a modular extension for ASP.NET Web Optimization Framework: Bundle Transformer 1.6.5: Version: 1.6.5 Published: 10/12/2012 In the configuration elements css and js added the usePreMinifiedFiles attribute, which enables/disables usage of pre-minified files; Added translator-adapter, which produces translation of TypeScript-code to JS-code; In BundleTransformer.MicrosoftAjax added support of the Microsoft Ajax Minifier 4.69; In BundleTransformer.Yui added support of the YUI Compressor for .NET 2.1.0.0; In BundleTransformer.Csso added support of the CSSO version 1.3.4. ...OrgCharts for SharePoint: OrgChart web part for SharePoint: Key features: • Central License management so no need to remember the license key details when adding to pages. • Builtin-asp.net caching for high performing loading of the Org Chart. • Create Org Chart from SharePoint list data OR SQL server queries. • Multi-level drill through • Use SharePoint lists or SQL Data as datasource • Support node level Images. {Example: Peoples my site photos} • AJAX enabled for fast client side processing • Optionally set the TAB field for an Auto-generated TAB i...mojoPortal: 2.3.9.3: see release notes on mojoportal.com http://www.mojoportal.com/mojoportal-2393-released Note that we have separate deployment packages for .NET 3.5 and .NET 4.0, but we recommend you to use .NET 4, we will probably drop support for .NET 3.5 once .NET 4.5 is available The deployment package downloads on this page are pre-compiled and ready for production deployment, they contain no C# source code and are not intended for use in Visual Studio. To download the source code see getting the lates...OstrivDB: OstrivDB 0.1: - Storage configuration: objects serialization (Xml, Json), storage file compressing, data block size. - Caching for Select queries. - Indexing. - Batch of queries. - No special query language (LINQ used). - Integrated sorting and paging. - Multithreaded data processing.D3 Loot Tracker: 1.5.4: Fixed a bug where the server ip was not logged properly in the stats file.Captcha MVC: Captcha Mvc 2.1.2: v 2.1.2: Fixed problem with serialization. Made all classes from a namespace Jetbrains.Annotaions as the internal. Added autocomplete attribute and autocorrect attribute for captcha input element. Minor changes. v 2.1.1: Fixed problem with serialization. Minor changes. v 2.1: Added support for storing captcha in the session or cookie. See the updated example. Updated example. Minor changes. v 2.0.1: Added support for a partial captcha. Now you can easily customize the layout, s...DotNetNuke® Community Edition CMS: 06.02.04: Major Highlights Fixed issue where the module printing function was only visible to administrators Fixed issue where pane level skinning was being assigned to a default container for any content pane Fixed issue when using password aging and FB / Google authentication Fixed issue that was causing the DateEditControl to not load the assigned value Fixed issue that stopped additional profile properties to be displayed in the member directory after modifying the template Fixed er...Advanced DataGridView with Excel-like auto filter: 1.0.0.0: ?????? ??????Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.69: Fix for issue #18766: build task should not build the output if it's newer than all the input files. Fix for Issue #18764: build taks -res switch not working. update build task to concatenate input source and then minify, rather than minify and then concatenate. include resource string-replacement root name in the assumed globals list. Stop replacing new Date().getTime() with +new Date -- the latter is smaller, but turns out it executes up to 45% slower. add CSS support for single-...WinRT XAML Toolkit: WinRT XAML Toolkit - 1.3.3: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features Attachable Behaviors AwaitableUI extensions Controls Converters Debugging helpers Extension methods Imaging helpers IO helpers VisualTree helpers Samples Recent changes NOTE:...VidCoder: 1.4.4 Beta: Fixed inability to create new presets with "Save As".MCEBuddy 2.x: MCEBuddy 2.3.2: Changelog for 2.3.2 (32bit and 64bit) 1. Added support for generating XBMC XML NFO files for files in the conversion queue (store it along with the source video with source video name.nfo). Right click on the file in queue and select generate XML 2. UI bugifx, start and end trim box locations interchanged 3. Added support for removing commercials from non DVRMS/WTV files (MP4, AVI etc) 4. Now checking for Firewall port status before enabling (might help with some firewall problems) 5. User In...Sandcastle Help File Builder: SHFB v1.9.5.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This release supports the Sandcastle October 2012 Release (v2.7.1.0). It includes full support for generating, installing, and removing MS Help Viewer files. This new release suppor...ClosedXML - The easy way to OpenXML: ClosedXML 0.68.0: ClosedXML now resolves formulas! Yes it finally happened. If you call cell.Value and it has a formula the library will try to evaluate the formula and give you the result. For example: var wb = new XLWorkbook(); var ws = wb.AddWorksheet("Sheet1"); ws.Cell("A1").SetValue(1).CellBelow().SetValue(1); ws.Cell("B1").SetValue(1).CellBelow().SetValue(1); ws.Cell("C1").FormulaA1 = "\"The total value is: \" & SUM(A1:B2)"; var...Json.NET: Json.NET 4.5 Release 10: New feature - Added Portable build to NuGet package New feature - Added GetValue and TryGetValue with StringComparison to JObject Change - Improved duplicate object reference id error message Fix - Fixed error when comparing empty JObjects Fix - Fixed SecAnnotate warnings Fix - Fixed error when comparing DateTime JValue with a DateTimeOffset JValue Fix - Fixed serializer sometimes not using DateParseHandling setting Fix - Fixed error in JsonWriter.WriteToken when writing a DateT...Readable Passphrase Generator: KeePass Plugin 0.7.2: Changes: Tested against KeePass 2.20.1 Tested under Ubuntu 12.10 (and KeePass 2.20) Added GenerateAsUtf8 method returning the encrypted passphrase as a UTF8 byte array.JSLint for Visual Studio 2010: 1.4.2: 1.4.2patterns & practices: Prism: Prism for .NET 4.5: This is a release does not include any functionality changes over Prism 4.1 Desktop. These assemblies target .NET 4.5. These assemblies also were compiled against updated dependencies: Unity 3.0 and Common Service Locator (Portable Class Library).New ProjectsATM Stimulate Using WCF Service: This project is my homework Basic Events: Basic Events makes it easier for developers to use out of the box events with basic properties in their eventargs like string message and datetime.BCCP-DEX: sumary not avaibleBing Maps TypeScript Declarations: Unofficial TypeScript declarations for the Bing Maps v7 AJAX Control.CodePlex Practice: Testing CodePlexDepIC: Dependency Injection Container with a very simple API.DNN TaskManger: This is the a project build with the DotNetNuke task manager tutorial videos series.Document Importer For SharePoint: Quickly import large volumes of documents into SharePoint document libraries using an effective user interface.Drop Me!!: cOMING SOON...wORKING ON THISGesPro: PFE de fin de BAC MB MLGL2DX (OpenGL to DirectX Wrapper Library): GL2DX is a wrapper library that allows you to build your OpenGL app for WinRT.MoControls - XNA 4 GUI Controls Library: XNA 4 GUI Controls Library aimed to simplify porting of a XNA 4.0 GUI interface to various platforms.Morph implementation in Delphi: Morph Protocol implementation written in Delphi XE3. Morph is a very powerful application level protocol. For more about Morph, go to http://morph.codeplex.com/Musicallis: Projeto da disciplina de Técnicas de Programação Aplicada II da Universidade Presbiteriana Mackenzie - SP.NHook - A debugger API for your hooking projects: A debugger API for your hooking projectsOperation Timber System: This is a Timber system aimed at merchants/wholesalers/Mills. It is only in design phase.Oryon .Net Extension Methods Library: This project contains a lot of useful extension methods for .Net Applications.OstrivDB: OstrivDB is an embedded NoSQL database engine.Outreach02: A research project for website development.PARCIAL-CP-2012: Proyecto De Calidad y Pruebas de Software - Examen ParcialProject13261011: dfdsfProject13271011: 11project-3D-fabien: C# project 3D IN4M12 -->http://www.esiee.fr/~mustafan/IN4M12-13/Pulsar Programming Language: Pulsar, is a free open source programming language alternative to Assembly. Create your dream Operating System without using Assembly, or C#, or C++!Scoot: A rowing club management application.Sfaar Bytex: an hexadecimal file readerSSIS RAW File Viewer: SSIS 2008 RAW file viewer.testddgit1011201201: ttesttom10112012tfs02: fdsf fsd???WindowsPhone???: ???Windows Phone??????www.yidingcan.com?????。??????、??

    Read the article

  • Free Developer Day - Hands-on Oracle 11g Applications Development

    - by [email protected]
    Spend a day with us learning the key tools, frameworks, techniques, and best practices for building database-backed applications. Gain hands-on experience developing database-backed applications with innovative and performance-enhancing methods. Meet, learn from, and network with Oracle database application development experts and your peers. Get a chance to win a Flip video camera and Oracle prizes, and enjoy post-event benefits such as advanced lab content downloads.Bring your own laptop (Windows, Linux, or Mac with minimum 2Gb RAM) and take away scripts, labs, and applications*.Space is limited. "Register Now"  for this FREE event. Don't miss your exclusive opportunity to meet with Oracle application development & database experts, win Oracle Trainings, and discuss today's most vital application development topics.          Win two Oracle Trainings valued in $2500 each. Offered by SDT Learning Corp·         Oracle Application Express: Developing Web Applications (duración de 4 días)·         Oracle Fusion Middleware 11g: Java Programming Ed 1.1 (duración de 5 días)You can also be registered Calling to Jamielle Gandía at 787-999-3187Requirements by TrackFor .Net Track1) A windows machine with 2 GB memory2) Attendees must in advance of the show, download and install VMWare player:       http://www.vmware.com/products/player/3) Attendees should test their machine to make sure they can run an executable on an external USB hard drive (some corporate machines are locked down so they cannot do this)For Java TrackYou will save time if you install these applications in advance:1) A windows machine with 2 GB memory2) VirtualBox must be installed in each laptopWhat is virtual box? Where can I download it?For APEX Track1) A windows machine with 2 GB memoryOracle Corporate agenda @  HereNote:  (Limited to 50 people per Track)

    Read the article

  • Why Wouldn't Root Be Able to Change a Zone's IP Address in Oracle Solaris 11?

    - by rickramsey
    You might assume that if you have root access to an Oracle Solaris zone, you'd be able to change the root's IP address. If so, you'd proceed along these lines ... First, you'd log in: root@global_zone:~# zlogin user-zone Then you'd remove the IP interface: root@user-zone:~# ipadm delete-ip vnic0 Next, you'd create a new IP interface: root@user-zone:~# ipadm create-ip vnic0 Then you'd assign the IP interface a new IP address (10.0.0.10): root@user-zone:~# ipadm create-addr -a local=10.0.0.10/24 vnic0/v4 ipadm: cannot create address: Permission denied Why would that happen? Here are some potential reasons: You're in the wrong zone Nobody bothered to tell you that you were fired last week. The sysadmin for the global zone (probably your ex-girlfriend) enabled link protection mode on the zone with this sweet little command: root@global_zone:~# dladm set-linkprop -p \ protection=mac-nospoof,restricted,ip-nospoof vnic0 How'd your ex-girlfriend learn to do that? By reading this article: Securing a Cloud-Based Data Center with Oracle Solaris 11 by Orgad Kimchi, Ron Larson, and Richard Friedman When you build a private cloud, you need to protect sensitive data not only while it's in storage, but also during transmission between servers and clients, and when it's being used by an application. When a project is completed, the cloud must securely delete sensitive data and make sure the original data is kept secure. These are just some of the many security precautions a sysadmin needs to take to secure data in a cloud infrastructure. Orgad, Ron, and Richard and explain the rest and show you how to employ the security features in Oracle Solaris 11 to protect your cloud infrastructure. Part 2 of a three-part article on cloud deployments that use the Oracle Solaris Remote Lab as a case study. About the Photograph That's the fence separating a small group of tourist cabins from a pasture in the small town of Tropic, Utah. Follow Rick on: Personal Blog | Personal Twitter | Oracle Forums   Follow OTN Garage on: Web | Facebook | Twitter | YouTube

    Read the article

  • Direct IO enhancements in OVM Server for SPARC 2.2(a.k.a LDoms2.2)

    - by user12611315
    The Direct I/O feature has been available for LDoms customers since LDoms2.0. Apart from the latest SR-IOV feature in LDoms2.2, it is worth noting a few enhancements to the Direct I/O feature. These are: Support for Metis-Q and Metis-E cards. These cards are highly requested for support and are worth mentioning because they are the only combo cards containing both FibreChannel and Ethernet in the same card. With this support, a customer can have both SAN storage and network access with just one card and one PCIe slot assigned to a logical domain. This reduces cost and helps when there are less number of slots in a given platform. The following are the part numbers for these cards. I have tried to put the platforms on which each card is supported, but this information can get quickly outdated. The accurate information can be found at the Support Document.  Card Name  Part Number  Platforms Metis-Q: StorageTek Dual 8Gb Fibre Channel Dual GbE ExpressModule HBA, QLogic SG-XPCIEFCGBE-Q8-N  SPARC T3-4, T4-4 Metis-E: StorageTek Dual 8Gb Fibre Chanel Dual GbE ExpressModule HBA, Emulex SG-XPCIEFCGBE-E8-N SPARC T3-4, T4-4  Additional cards added to the portfolio of supported cards. This is mainly Powerville based Ethernet cards, the part numbers for these cards as below:  Part Number  Description  7100477 Sun Quad Port GbE PCI Express 2.0 Low Profile Adapter, UTP  7100481 Sun Dual Port GbE PCI Express 2.0 Low Profile Adapter, MMF  7100483 Sun Quad Port GbE PCI Express 2.0 ExpressModule, UTP  7110486 Sun Quad Port GbE PCI Express 2.0 ExpressModule, MMF    Note:  Direct IO feature has a hard dependency on the Root domain(PCIe bus owner, here Primary domain). That is, rebooting the Root domain for any reason may impact the logical domains having PCIe slots assigned with Direct IO feature. So rebooting a root domain need to be carefully managed. Also apply the failure-policy settings as described in the admin guide and release notes to deal with unexpected cases.

    Read the article

  • Sharing swap space between Windows and Ubuntu

    - by Leftium
    This Linux Swap Space Mini-HOWTO describes how to share swap space between Windows and Linux. Do these instructions still apply to Ubuntu in 2011? How should I modify the steps for Ubuntu? Is there a better approach to sharing swap space? Based on the HOWTO, it seems best to create a dedicated NTFS swap partition: Dedicated so the swap file will be contiguous and remain unfragmented. NTFS so both Windows and Ubuntu can read/write to it. (Or is FAT32 better for this purpose?) Then, configure Ubuntu to prepare the swap space for use by Linux on start up; by Windows on shut down. I want to dual boot Ubuntu and Windows 7 on my X301 laptop. However, my laptop only has a 64 GB SDD, so I would like to conserve as much disk space as possible. update: There is an alternate method using a special driver for Windows that let you use a Linux swap partition for temporary storage like a RAM-disk, but it doesn't seem to be as good...

    Read the article

  • PHP - Making CMS (architecture, etc.)

    - by UnknownProgramer
    I'm in the stage of planning new CMS. Before I used WordPress and other open source CMS for my clients, but I always had to write new modules and even mess with the code in order to do certain things. Which as you understand is not the best thing to do. So I finally decided to make my own CMS to work with, the way I need. But before I start it, I would like to think it trough carefully to ensure that I won't need to rewrite it ground up, just because I forgot to include some feature into architecture or did it wrong. I would like to hear your thoughs and the most important I would like you to suggest me some articles or books on that subject, especially on architecture of such systems. I googled a few good books, but that is not enough. The way I'm planning to do it: PHP5, completely OOP, modules architecture. You make a page and add any modules you need there, but modules are not global, but local to a page so you can make two pages with the same module, but content will be different if you set different "content ID" for these two entities. But it can be set the same, so two pages has the same content of the modules put there. Also I plan to support online storage web service (like amazon S3) for images and files, so I would like to hear your thoughs on it too. Also I have not yet decided how to store language data. I don't want to use DB for that, but I haven't decided yet. Also I think I will support other DB with global DB class and separate DB wrappers for MySQL and other databases. And, well, I would appreciate any other information you can provide for that subject.

    Read the article

  • computer shows up twice, connection unknown

    - by Thomas G. Seroogy
    added two computers to Ubuntu One. One machine is windows. The windows version seems to work fine, and I started syncing a folder by placing it into the Ubuntu One folder. All files and folders are visible when I go to my account online. On Ubuntu machine. I selected to sync the Download folder. Shortly thereafter, I realized that one folder exceeded my storage max. I tried to un-sync the folder, but Ubuntu One and the Stop Syncing This Folder were not visible in the menu. Per Ubuntu instructions, I removed my Ubuntu computer from the list of syncing computers. Per Ubuntu instructions, I re-added the Ubuntu computer. However, I find that two computers by the same name are added on both the desktop app and on the web. Plus, I the connection is "unknown." I have removed and re-added the computer several times with the same results. In all cases, I remove the computers using the Ubuntu One desktop app, then removing them from my account on the web, removing the Ubuntu One password, and restart the Ubuntu One app. Problem remains. Thanks in advance for any replies and help.

    Read the article

  • New Book: Oracle Exalogic Elastic Cloud Handbook

    - by user12608550
    Oracle Exalogic Elastic Cloud Handbook, by Tom Plunkett, TJ Palazzolo, and Tejas Joshi, Oracle Press. The well-known characteristics and tiers of cloud computing have spawned myriad implementations by a host of vendors and system integrators. One of these, Oracle's Exalogic Elastic Cloud, part of Oracle's family of Engineered Systems, is a key component of Oracle's public and private cloud computing solutions, providing critical PaaS (Platform as a Service) features for cloud developers. These developers need guidance to take advantage of Exalogic's extensive capabilities, and the Oracle Exalogic Elastic Cloud Handbook, written by three highly experienced Oracle technologists, provides that guidance. Part One of the book covers Exalogic's hardware and software components, and includes a very useful chapter on deployment examples, describing best practices for scalabiity, availability, backup and recovery, and multi-tenant security, including integration with other Oracle Engineered Systems and products such as Exadata and storage subsystems. Part Two is a thorough guide to Exalogic installation features, configuration and monitoring, packaged application software management, and scalable application development. The book also provides an extensive list of online resources, including pointers to Web sites, whitepapers, instructional videos, and other Oracle documentation. So, if you're planning to implement Exalogic as part of your cloud infrastructure, or are considering such, you'll find lots of sage advice and best practices in this handbook.

    Read the article

  • How to make pulseaudio and ubuntu detect the same audio device as alsa driver

    - by Kiwy
    I use Ubuntu 14.04 x64 and I use gnome-shell on my laptop. I have a Bose companion 5 (which is basically a USB sound system) and a HDMI port, both does work perfectly when I just boot with the cable plugin. However, when my laptop go to sleep or get unplugged from those two outputs, if I plug back the device, I end up without any hardware detection (only the built-in speakers) from pulse and gnome-shell sound output selector while if I use alsamixer, the device look up and ready. gstreamer-properties allow me to select and test effectively any device but while alsa recognize any device on the run, pulse is not capable of handling things correctly, my question is then: How can I make pulse detect and use the same hardware as alsa, or how to remove completely and gracefully pulseaudio (meaning volume applet running in gnome shell) I don't mind if the project implies to recompile half gnome shell if it implies those audio outputs work all the time. Pulse does not list my soundcard when I use command pactl list cards while the module plug&play for sound card is loaded in pactl list modules. I really don't know what to do, the behavior seems pretty random.

    Read the article

  • Problem Installing Ubuntu 12.04 - [Errno 5]

    - by Rob Barker
    I'm trying to intall Ubuntu 12.04 to my brand new eBay purchased hard drive. Only got the drive today and already it's causing me problems. The seller is a proper proffesional company with 99.9% positive feedback, so it seems unlikely they would have sold me something rubbish. My old hard drive packed up last Tuesday and so i bought a new one to replace it. Because this was an entirely new drive i decided to install Ubuntu as there was no current operating system. My computer is an eMachines EM250 netbook. There's no disc drive so i am installing from a USB stick. The new operating system loads beautifully, and the desktop appears just as it should. When i click install i am taken to the installer which copies the files to about 35% and then displays this: [Errno 5] Input/output error This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment. The hard drive can be heard constantly crackling. When i booted Ubuntu 12.04 from my old faulty hard drive as a test, i didn't even make it past the purple Ubuntu screen, so it can't be that bad. Any ideas? Message to the moderators. Please do not close this thread. I'm well aware there may be other threads on this, but i don't want it closing as the others do not provide the answer i am looking for. Thank you.

    Read the article

  • Oracle Solaris Remote Lab (OSRL) Fact Sheet

    - by user13333379
    The Oracle Solaris Remote Lab allows independent software vendors (ISVs) to test and qualify their applications in a self service Solaris cloud. ISVs who are Oracle Partner Network Gold members with a specialization in the Solaris knowledge zone can apply for free access in OPN. The lab offers the following features to it's users: Lifetime of project: 45 days (extensions granted on demand)  Up to 5 virtual machines in a private network  Virtual Machine technology: Solaris zones  Resources per VM processor support: SPARC or x86  OS version: OracleSolaris 11.0 4GB physical memory  4GB swap space  10GB local filesystem storage  10GB network filesystem (NFS) mounted on all virtual machines Networking configuration The only external network routes are to Partner's other Virtual Machines  No network routing to the Internet  The SMB (CIFS) sharing protocol is not available between Virtual Machines  Device Access  Applications that assume the existence of /devices will not run in a Virtual Machine  Applications that use eeprom to modify SPARC eeprom setting will not run in a Virtual Machine The following utilities do not work properly in Virtual Machines:  add_drv, disks, prtconf, prtdiag, rem_dev Access technology: Secure Global Desktop, file up and download root access within VM Available VM templates (both processor architectures) Oracle Database 11g Release 2 (11.2.0.3) for Solaris with Oracle Enterprise Manager 11g Weblogic 12c  SAMP: Apache http server, PHP, MySQL, phpadmin on all templates and images: Oracle Solaris Studio 12.3 for application development  More resources: Online application for Oracle Solaris remote Lab Developer Webinar about the Oracle Solaris Remote Lab Everything an Oracle Solaris Developer needs...

    Read the article

  • Oracle Solaris Remote Lab (OSRL) Fact Sheet

    - by user13333379
    The Oracle Solaris Remote Lab allows independent software vendors (ISVs) to test and qualify their applications in a self service Solaris cloud. ISVs who are Oracle Partner Network Gold members with a specialization in the Solaris knowledge zone can apply for free access in OPN. The lab offers the following features to it's users: Lifetime of project: 45 days (extensions granted on demand)  Up to 5 virtual machines in a private network  Virtual Machine technology: Solaris zones  Resources per VM processor support: SPARC or x86  OS version: OracleSolaris 11.0 4GB physical memory  4GB swap space  10GB local filesystem storage  10GB network filesystem (NFS) mounted on all virtual machines Networking configuration The only external network routes are to Partner's other Virtual Machines  No network routing to the Internet  The SMB (CIFS) sharing protocol is not available between Virtual Machines  Device Access  Applications that assume the existence of /devices will not run in a Virtual Machine  Applications that use eeprom to modify SPARC eeprom setting will not run in a Virtual Machine The following utilities do not work properly in Virtual Machines:  add_drv, disks, prtconf, prtdiag, rem_dev Access technology: Secure Global Desktop, file up and download root access within VM Available VM templates (both processor architectures) Oracle Database 11g Release 2 (11.2.0.3) for Solaris with Oracle Enterprise Manager 11g Weblogic 12c  SAMP: Apache http server, PHP, MySQL, phpadmin on all templates and images: Oracle Solaris Studio 12.3 for application development  More resources: Online application for Oracle Solaris remote Lab Developer Webinar about the Oracle Solaris Remote Lab Everything an Oracle Solaris Developer needs...

    Read the article

  • Local file system not properly unmounted during shutdown

    - by bernhard
    I have a file system with two HDDs and several partitions mounted separately locally. /root, /home, /usr, /var, /local/share , /home/bernhard/fotos/bilder, /backup are on separate partitions and are all ext3. During unmounting the message "unmounting local file system" does not appear any further and when booting all partitions but the root partition have to reload the journal, which indicates improper unmounting. The root partition and /usr are on sda, the others on sdb or further usb-mounted devices. the only partition unmounted w/o problem seems to be the root partition on sda4. I wonder whether the script to umount all devices has a "wait for success" loop or that the script itself got corrupted. However, yesterday I upgraded to 11.04 and the error persists. pmount does not look to be appropriate since the device are not hotplugged but simply mounted during system start. Obviously mounting /usr and afterwards /usr/local/share as well as /home and later /home/bernhard/fotos/bilder presents problems for umount; the devices may be busy und thus not properly unmounted. Does anybody have an idea for a script to organize unmounting in an ordered way? How to wait for unmounting of the secondary mount? Do you know as well where to place such a script that it will be used instead of the original umount command? Could be a general solution.

    Read the article

  • Hot Off the Press - Oracle Exadata: A Data Management Tipping Point

    - by kimberly.billings
    Advances in data-management architecture - including CPU, memory, storage, I/O, and the database - have been steady but piecemeal. In this report, Merv Adrian describes how Oracle Exadata not only provides the latest technology in each part of the data-management architecture, but also integrates them under the full control of one vendor with a unified approach to leveraging the full stack. He writes, "the real "secret sauce" of Oracle Exadata V2 is the way in which these technologies complement each other to deliver additional performance and scalability." Merv interviews two Exadata customers, Banco Transylvania and TUI Netherlands, and concludes that early indications are that Oracle Exadata is delivering on its promise of extreme performance and scalability. His recommendation to IT is to target corporate applications with the biggest potential for speed-based enhancement, and consider whether Oracle Exadata V2 can cost-effectively enable new ways to use these for competitive advantage. Read the full report. var gaJsHost = (("https:" == document.location.protocol) ? "https://ssl." : "http://www."); document.write(unescape("%3Cscript src='" + gaJsHost + "google-analytics.com/ga.js' type='text/javascript'%3E%3C/script%3E")); try { var pageTracker = _gat._getTracker("UA-13185312-1"); pageTracker._trackPageview(); } catch(err) {}

    Read the article

  • Another guvcview issue? Core dump!

    - by user290498
    guvcview is core dumping with my Sony Handycam plugged in. It works fine with my standard Logitech Webcam. I deleted the config file so it could re-create it. here is the output: $ guvcview guvcview 1.5.3 Could not open /home/rayj/.guvcviewrc for read, will try to create it write /home/rayj/.guvcviewrc OK ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 ERROR opening V4L2 interface for /dev/video1 Init. stk1160 (location: usb-0000:00:1d.0-1.5) { pixelformat = 'UYVY', description = '16 bpp YUY2, 4:2:2, packed' } VIDIOC_ENUM_FRAMESIZES - Error enumerating frame sizes: Inappropriate ioctl for device Unable to enumerate frame sizes. : Inappropriate ioctl for device { pixelformat = 'RGB3', description = 'RGB3' } { ?GSPCA? : width = 720, height = 480 } fmtind:2 fsizeind: 1 { pixelformat = 'BGR3', description = 'BGR3' } { ?GSPCA? : width = 720, height = 480 } fmtind:3 fsizeind: 1 { pixelformat = 'YU12', description = 'YU12' } { ?GSPCA? : width = 720, height = 480 } fmtind:4 fsizeind: 1 { pixelformat = 'YV12', description = 'YV12' } { ?GSPCA? : width = 720, height = 480 } fmtind:5 fsizeind: 1 vid:05e1 pid:0408 driver:stk1160 checking format: 1196444237 Format unavailable: 1196444237. Init v4L2 failed !! Init video returned -2 trying minimum setup ... Segmentation fault (core dumped)

    Read the article

  • Oracle VM Server for x86 Training Schedule

    - by Antoinette O'Sullivan
    Learn about Oracle VM Server for x86 to see how you can accelerate enterprise application deployment and simplify lifecycle management with fully integrated support from physical to virtual servers including applications. Oracle offers a 3 day course Oracle VM Administration: Oracle VM Server for x86. This course  teaches you how to: Build a virtualization platform using the Oracle VM Manager and Oracle VM Server for x86. Deploy and manage highly configurable, inter-connected virtual machines. Install and configure Oracle VM Server for x86 as well as details of network and storage configuration, pool and repository creation, and virtual machine management. You can take this course as follows: Live Virtual Class - taking the course from your own desktop accessing a live teach by top Oracle instructors and accessing extensive hands-on exercises. No travel necessary. Over 300 events are current scheduled in many timezones across the world. See the full schedule by going to the Oracle University Portal and clicking on Virtualization. In Classroom - Events scheduled include those shown below:  Location  Date  Delivery Language  Warsaw, Poland  6 August 2012  Polish  Istanbul, Turkey  10 September 2012  Turkish  Dusseldorf, Germany  6 August 2012  German  Munich, Germany  10 September 2012  German  Paris, France  17 October 2012  French  Denver, Colorado, US  30 July 2012  English  Roseville, Minnesota, US  23 July 2012  English  Sydney, Australia  3 September  English For more information on this course and these events or to search for additional events or register your interest in an additional event/location, please visit the Oracle University Portal and click on Virtualization.

    Read the article

  • How can I get run Ubuntu Desktop on my Galaxy Nexus?

    - by Jack Senechal
    On the Ubuntu for phones site it advertises the desktop view feature: "The phone becomes a full PC and thin client when docked.". And there's the demo by Canonical of something similar running under Ubuntu for Android. I realize they're different systems, but the end effect is in both is to have a full Ubuntu system running on the phone. I've installed Ubuntu Touch Preview on my Galaxy Nexus (toro), and it's working as expected (no cellular signal, but wifi works, etc). But when I plug in a monitor via HDMI it just mirrors the phone's touch display. There's also currently no bluetooth support for attaching keyboard and mouse. Keyboard only kind of works via USB, and mouse not at all. I've also tried running Ubuntu under Android via VNC, but the lack of responsiveness of VNC makes it impractical for daily use. I'd consider that route again if there is some way to make the UI more responsive. So the question is, how can set up my phone to run Ubuntu Desktop in a way that's useable as a laptop replacement? Is there a way to enable Desktop View on Ubuntu Touch? Or can I run Ubuntu for Android as in the previously referenced demo? Plugging into a monitor would be OK, but I'd love to be able to use the desktop interface with mouse and keyboard through the phone's screen as well. Touch input and an onscreen keyboard would be a plus but is definitely not necessary.

    Read the article

  • Software design of a browser-based strategic MMO game

    - by Mehran
    I wonder if there are any known tested software designs for Travian-like browser-based strategic MMO games? I mean how would they implement the server of such games or what is stored in database and what is stored in RAM? Is the state of the world stored in one piece or is it distributed among a number of storage? Does anyone know a resource to study the problems and solutions of creating such games? [UPDATE] Suggested in comments, I'm going to give an example how would I design such a project. Even though I'm not sure if I'm proposing the right one. Having stored the world state in a MongoDB, I would implement an event collection in which all the changes to the world will register. Changes that are meant to happen in the future will come with an action date set to the future and those that are to be carried out immediately will be set to now. Having this datastore as the central point of the system, players will issue their actions as events inserted in datastore. At the other end of the system, I'll have a constant-running software taking out events out of the datastore which are due to be carried out and not done yet. Executing an event means apply some update on the world's state and thus the datastore. As scalable as this design sounds, I'm not sure if it will be worth implementing. For one, it is pointless to cache the datastore as most of updates happen once without any follow ups. For instance if you have the growth of resources in your game, you'll be updating the whole world state periodically in which case, having incorporated a cache, you are keeping the whole world in RAM (which most likely is impossible). So can someone come up with a better design?

    Read the article

  • Dirt Cheap Bi-Directional Antenna Wirelessly Extends Your LAN

    - by Jason Fitzpatrick
    If you’re looking for an effective way to link remote LANs without the hassle of laying cable, this DIY bi-directional antenna is a quick (and cheap) method for bringing internet access to outbuildings and other locations. Tinker Danilo Larizza needed to share internet access between apartments that are relatively close together but not hardwired–ruling out simply sharing the access via existing LAN infrastructure. His solution combines a simple scrap wire antenna array mounted inside a plastic food bin (seen here with the cover removed to show the antenna) and some coaxial cable to link the antenna to two routers. Our favorite part about his build is that he constructed the pair to establish if the antenna setup would even work in his location and intended to buy commercial antennas if it did; his Tupperware models worked so well, however, they’re now the permanent solution. Hit up the link below for more information about the project. 2.4 Ghz Directive Biquad Antenna [via Hack A Day] How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It

    Read the article

  • Java Spotlight Episode 98: Cliff Click on Benchmarkings

    - by Roger Brinkley
    Interview with Cliff Click of 0xdata on benchmarking. Recorded live at JFokus 2012. Right-click or Control-click to download this MP3 file. You can also subscribe to the Java Spotlight Podcast Feed to get the latest podcast automatically. If you use iTunes you can open iTunes and subscribe with this link:  Java Spotlight Podcast in iTunes. Show Notes News Bean Validation 1.1 Java EE 7 Roadmap Java JRE Update 7u7 and 6u35 available. Change to Java SE 7 and Java SE 6 Update Release Numbers JCP 2012 Award Nominations Announced Griffon JavaFX Plugin Events Sep 3-6, Herbstcampus, Nuremberg, Germany Sep 10-15, IMTS 2012 Conference,  Chicago Sep 12,  The Coming M2M Revolution: Critical Issues for End-to-End Software and Systems Development,  Webinar Sep 30-Oct 4, JavaONE, San Francisco Oct 3-4, Java Embedded @ JavaONE, San Francisco Oct 15-17, JAX London Oct 30-Nov 1, Arm TechCon, Santa Clara Oct 22-23, Freescale Technology Forum - Japan, Tokyo Nov 2-3, JMagreb, Morocco Nov 13-17, Devoxx, Belgium Feature Interview Cliff Click is the CTO and Co-Founder of 0xdata, a firm dedicated to creating a new way to think about web-scale data storage and real-time analytics. I wrote my first compiler when I was 15 (Pascal to TRS Z-80!), although my most famous compiler is the HotSpot Server Compiler (the Sea of Nodes IR). I helped Azul Systems build an 864 core pure-Java mainframe that keeps GC pauses on 500Gb heaps to under 10ms, and worked on all aspects of that JVM. Before that I worked on HotSpot at Sun Microsystems, and am at least partially responsible for bringing Java into the mainstream. I am invited to speak regularly at industry and academic conferences and has published many papers about HotSpot technology. I hold a PhD in Computer Science from Rice University and about 15 patents. What’s Cool Shaun Smith’s Devoxx 2011 talk "JPA Multi-Tenancy & Extensibility" now freely available at Parleys.

    Read the article

< Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >