Search Results

Search found 2415 results on 97 pages for 'asus motherboard'.

Page 35/97 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

  • Booting From VIA VT6421A Based PCI SATA Card

    - by Priyan R
    I bought a VIA VT6421A based SATA card for an 845 chipset based motherboard. The card is working i can access sata hdd from windows/linux. The problem is i can't directly boot from the sata card. My motherboard is award bios 6 based. I tried first boot as SCSI, its not worked. There is no Raid Bios screen appeared from the card. On searching i found , Add VT6421A bios to system bios as pci addon bios. I did it using cbrom6 , successfully added VT6421A bios to the existing bios. But now on booting instead of raid bios system bios showed Warning : something like cannot load add on rom for vendor id xxxx device id xxx . Whats wrong ? As the card is VT6421A based and i added VT6421A bios got from VIA website.

    Read the article

  • Windows 7 64 Bit Can't Get Past Format

    - by Soren
    favorite Just assembled a new machine: MSI 880GM-E41 motherboard 500GB Samsung hard drive AMD Athlon II X4 640 processor 4GB RAM Windows 7 64 Bit LITE-ON Black 4X Blu-ray reader I boot up, start the install. When it gets to the screen to select what partition, the motherboard loses power. It doesnt make sense, I can leave it in the bios settings for a very long time and it doesnt lose power. When it does lose power, the monitor shuts down and the mouse loses power, but the power light stays on. I cannot tell if it is a harware or software problem.

    Read the article

  • Video Card needs additional mounting support

    - by Sean
    We are creating a fairly decent system with crossfire. The issue we are having is apparently the video cards are physically to heavy to be supported purely by the motherboard and case mounts. Whenever we have the case horizontal everything works fine however when we bring the case upright the computer stops working. Relevant Info: Video Cards (2) - Sapphire 5870 (http://www.newegg.com/Product/Product.aspx?Item=N82E16814102856) MotherBoard - Asus M4A79T Deluxe Case - CoolerMaster 922 HAF To me it looks as if an additional support bracket that could hold up the end of the card would be required (included with the viideo cards!!!) Does anyone have any experience with this.

    Read the article

  • Windows 7 Can't Get Past Format

    - by Soren
    Just assembled a new machine: MSI 880GM-E41 motherboard 500GB Samsung hard drive AMD Athlon II X4 640 processor 4GB RAM Windows 7 64 Bit LITE-ON Black 4X Blu-ray reader I boot up, start the install. When it gets to the screen to select what partition, the motherboard loses power. It doesnt make sense, I can leave it in the bios settings for a very long time and it doesnt lose power. When it does lose power, the monitor shuts down and the mouse loses power, but the power light stays on. I cannot tell if it is a harware or software problem.

    Read the article

  • Acer Aspire ASE700-UQ660A will not respond to power button

    - by Tim R.
    This is something of a continuation of this question. I am now completely unable to boot this computer. The last time I used it, I used hibernation mode. When I needed to use it again, it would not respond at all to the power button, keyboard, or mouse. I tried: Holding down the power button for 15 seconds pressing the power button Unplugging the power cord for 30 seconds, plugging it back in, and trying again Removing the motherboard battery for over a minute and reinstalling it Before removing the motherboard battery, none of the lights on the front of the computer lit up. After reinstalling the battery and plugging the power cord back in, the light behind the power button is constantly illuminated (without even pressing the power button), but there is still no response to the power button, no fans turned on, nothing else that would indicate that it is running. System: Acer Aspire ASE700-UQ660A (Specs should be all factory defaults except:) 4 GB RAM Nvidia GeForce 8600 GT with driver version 197.45 Windows 7 Professional 64 bit

    Read the article

  • Fan twitches and LEDs blink when computer is plugged in

    - by Zifre
    I just finished assembling a desktop for the first time. The specs are: Gigabyte GA-H55M-S2H motherboard Core i3 530 CPU 4 GB DDR3 RAM 1 TB SATA hard drive 500 Watt PSU As soon as I plug in the computer, the "phase LED" starts blinking orange and the system fan LED blinks while the fan "twitches". This continues until about three seconds after I unplug the computer. This worries me a lot because I haven't even turned the computer on and it continues even after there is no power. I did make sure the PSU is on the proper power setting. What is causing this and how can I fix it? Is the motherboard dead?

    Read the article

  • Xenserver boot error

    - by Adrian
    I'm trying to get Xenserver 5.5 running on a spare computer here, hardware specs: Intel Q6600, 4GB Ram, and Gigabyte GA-P35-DS3R motherboard Xenserver itself installs fine onto a 150GB sata hdd, however it fails to boot whatsoever, giving this garbled mess: http://img697.imageshack.us/img697/9918/biosi.jpg it's not frozen because if I press enter it just prints a different garble and it also says "could not find kernel image". The strangest thing is if I put that hdd in my desktop and assign it to a VMWare desktop vm (under the ESX profile no less) it boots perfectly... leading me to believe there are no problems with the install or the hdd itself. From what I can tell the error seems to be occuring completely seperately to Xenserver, in the bootloader extlinux?. If there was a motherboard compatibility issue I would think it would also have manifested during installation, and the fact the problem seems to be with the booting into Xen makes me doubt this. Any ideas guys? (I'm using Xen because it can do PCI passthrough without VT-d.)

    Read the article

  • GeForce 9600GT support for dual monitor setup

    - by Theo
    I have a NVIDIA GeForce 9600 GT (point of view, link) on an Asus M2V-MX motherboard. The card has one DVI, HDMI and S-Video output. The graphics card does not seem to support dual monitors: the driver control panel for the graphics card does not detect a second monitor that is attached via S-Video (which leads me to believe that it doesn't support dual monitors with DVI and the other connections). Would it be possible to use a VGA/DVI splitter to attach two monitors to the single DVI output on the graphics card? Would this allow for a dual monitor setup, or only mirroring? How do I know if the graphic card supports this? With this particular motherboard, would it be possible to use the onboard video for another monitor?

    Read the article

  • problem with monitor

    - by misha nesterenko
    I have an Asus VB191T connected to notebook via DVI connector as secondary monitor. I am observing some problems on that monitor. Photo of a properly functioning screen: Photo of my Asus VB191T screen: So as you can see there are white lines on both sides of black ones. Resolution is set to the monitor's native resolution which is 1280x1024. The artifacts don't appear for every color, and they show up the clearest where there is black on a grey background. What could be wrong? The monitor itself? Perhaps the connector?

    Read the article

  • Windows XP won't boot after drive transplant

    - by Nathan
    Hi all, I moved my hard drive from my Lenovo laptop into my Asus Eee PC netbook. When I started the netbook, after POST all I got was a black screen with a cursor in the upper left corner. I thought that the migration should work OK because this was a 32-bit version of Windows XP, and the Atom processor in the Asus should support the x86 instruction set. However, I don't know much about Windows, so maybe this was a dumb thought. I did verify that the BIOS can find the drive. It required major surgery to replace the drive, so any solution requiring me to remove the transplant drive is not going to fly. Keeping in mind that the netbook has no optical drive and that I have no other Windows computers (all my other computers run Linux), is there any way I can fix this problem? Thanks! Nathan

    Read the article

  • Windows 8 Disk Mirroring vs Intel Fake RAID

    - by Johnny W
    So Windows 8 is out and I have a new motherboard. I wish to create a RAID 1 coupling between two HDDs -- for storage purposes only (my OS is on an SSD) -- but I don't know which is the best route to take. My motherboard (Z77 chipset) comes with the age old Intel Fake RAID, but since I only wish to use my RAID for storage, I wondered if I might be better to use Windows 8 Disk Mirroring. Can anyone advise which is better? Or perhaps the pros and cons of each, if that's too contentious? I just can't see the benefit of FakeRAID. You can see my current setup here, if that might change things(?): Thanks!

    Read the article

  • Computer crashes and won't start, LED indicator blinks slowly

    - by hexacyanide
    I have a MSI K8NGM2-FID motherboard coupled with a AMD Athlon 3700+ and an Antec TPII-550 power supply. The computer crashes at random times in operation, sometimes taking a while to crash, and sometimes crashing right after Windows XP shows the desktop after boot. The CPU temperature is always in the safe range, usually 30-33 degrees Celsius, and swapping the RAM has not done anything, so the crashes aren't cause by the RAM. What could be causing this? If the motherboard were fried, would the computer even boot at all? What causes inconsistent crashing of the computer? After the computer crashes, the LED power indicator blinks about once a second, and the computer does not respond to the power button. This behavior continues until the computer's power supply is completely removed.

    Read the article

  • Windows 7 x64 installation freezes on new PC build

    - by jhsowter
    Symptoms While attempting to install Windows 7 (64 bit) on my new PC build, it freezes usually at the point where it is expanding the windows image, but has frozen as early as accepting the licence agreement, and as late as just after the first restart. My specs are at the bottom of the post. So far I have tried the following to identify the problem, in rough chronological order: Tried different hard drives with different sata cables. Same symptoms. I later used a different computer to install windows on the same hard drive with no problems. Tried the RAM in different slots, and tried one RAM stick instead of two. Same symptoms. Updated the BIOS to 1.60. Same symptoms. Ran Memtest86+ with RAM in dual channel. It passed about 6 times when I left it running overnight. Used USB to install windows instead of an optical drive. Same symptoms. Change SATA configuration from AHCI to IDE. Same symptoms. Tried various different SATA ports. Same symptoms. Updated BIOS to 1.70. Same symptoms. I saw the RAM did not list my motherboard as being supported even though the motherboard did list the RAM as being supported. So I tried some Kingston DDR3 1333MHz RAM instead. Same symptoms. Other (possibly) pertinent information My CPU idles at about 30 °C. I can't tell what it gets to when it's working. When I installed the CPU, the lever which locks the CPU in place took quite a bit of force to pull down. Now I didn't just yank it down without rechecking the CPU was seated properly about 5 times, but it does seems unusual, and I wonder if the CPU was seated badly if I would see these symptoms? I am out of ideas and don't know how to diagnose any further. I suppose either the motherboard or CPU must be the problem. I am on the verge of taking it to a specialist. The Question How should I proceed from here? Is there anything I can rule out as being the source of the symptoms I am seeing? My Specs CPU: Intel i5 3570k RAM: G.Skill RipjawsX 8GB kit HDD: single 3.5" 500GB SATA or 160GB 2.5" SATA (at different times and sometime together. But no RAID or anything). MB: ASRock Extreme4 Z77 PSU: Silverstone Strider Plus 600W ST60F-P

    Read the article

  • Dual boot Windows XP 32 bit and Windows 7 64-bit

    - by Santanu Roy
    My system config is AMD phenom-II x2 550 processor, 2x2gb(800fsb)ddr2 zion ram, gigabyte ga-m61pme-s2 motherboard, 160gb sata hdd. Now I am planning to install Windows XP sp3 (32-bit) and Windows 7 (64bit). My first questions are: Is my system enough for the above mentioned two OSes? Which OS one should be installed first on local disk c: drive? I have both XP and vista drivers on separate disks as provided with my motherboard but don't have drivers for win-7, so can I use my vista driver for win-7?

    Read the article

  • Realtek HD Audio 5.1 Optical Input (from Xbox 360)

    - by Shevek
    I'm trying to connect up my Xbox 360 digital audio to my 5.1 speakers via my PC (my LCD has dual input, DVI for the PC, D-SUB for the Xbox). The motherboard has a Realtek ALC888 chipset and I have a 5.1 speaker system connected via 3 x 3.5mm jacks (FR/FL, RR/RL, C/LFE) and I get full 5.1 output from the PC. I have connected the optical audio cable from the Xbox to the Optical In on the motherboard's backplate. With the Xbox in Digital Stereo mode I get 2 channel audio from the Xbox, through the PC, to the speakers. With the Xbox in Dolby Digital 5.1 mode I get no sound at all. I have the latest Realtek drivers installed in Win 7 32-bit. Questions: Is it possible to use the full 5.1 DD from the Xbox? If so, am I missing some option(s) in the Realtek setup? Do I need some other piece of software to do this? (AC3Filter or FFDShow perhaps) Many thanks

    Read the article

  • Linux: How to delay hddtemp service start at boot until all hdd are visible?

    - by Atis
    I live in a hot and humid environment, therefore I monitor the hdd temperature using hddtemp and gkrellm. There is an LSI9211 8i sata/sas controller in my computer. I have drives connected to both my motherboard and the LSI. hddtemp monitors only the drives directly connected to my motherboard after booting the system, therefore gkrellm displays the temperature of those drvies only. Logging in and restarting hddtemp before starting gkrellm fixes my issue, i.e. drives connected to the LSI controller are also visible. It seems that the drives connected to the LSI controller become visible only after hddtemp is started in the boot sequence. I think delaying it would help. How can I delay the starting of hddtemp till all drives are visible? I prefer a way to check if drives are visible to the delay of a specific amount of seconds.

    Read the article

  • How do i have 4GB of video memory with a 1GB video card?

    - by Tomas Spc Yaczik
    I ran the direct X diagnostic tool to take a look at my graphics capabilities and its telling me that the approximate video memory is clocked in at 4096MB. That doesn't make any sense, how is that possible? The only things that i can think of were that DirectX was inaccurate so i looked at the graphics statistics of my computer on CPU-Z which was included with the motherboard and that's telling me i have "negative" 1988MB. Not only is that not 4096MB, but its giving me a negative number and i know for a fact that you can't have a negative amount of memory???!!! The only things i can think of that would be amplifying my video memory output is the PCIe 3.0 bus, or that the motherboard is somehow including the on board video chip set with the video card which only then is only 2GB of video memory, which still has to be being amplified by something. Any suggestions?

    Read the article

  • Using an old PC case and power supply as a HDD Enclosure?

    - by mexiq
    I have 5 HDD and my computer is not handling the situation very well. hehe There are some towers that I can buy to put 4 of my drives out, but I'm thinking that I could use the power source of a failed computer I have and use it to power the 4 (or at least 3) of the drives. The data cables (SATA) will remain connected to the working computer (so no USB solution). The problem is that the power source will not work unless it is connected to the failing computer motherboard. Is there any way I could use the power source without plunging it to the old motherboard? Any "HOW-TO" links may be useful as well.

    Read the article

  • No compatible network card

    - by sbintcliffe
    Motherboard: Asus K8N-E Deluxe with onboard NIC (nVidia nForce) Secondary NIC: I've tried using a standard NIC (Device Manager displays this as D-Link DFE-538TX 10/100, but under manufacturer in the General tab of the properties in Windows it states Realtek Semiconductor Corp.) I have downloaded ESXi 4.0.0 build 208167 and cooked to disc. I've booted from it, the .TGZ modules load from the yellow and grey screen, the progress bar reaches to about 60% and like a second later the screen changes and I have the following information on screen; "No compatible network adapter found. Please consult the HCG." I've checked the HCG and found that my motherboard is listed. I also get the same message with the secondary NIC. Any ideas please?

    Read the article

  • Is it possible to use a dual processor computer as your desktop?

    - by Ivo
    I've seen some people suggesting to get a motherboard that supports two processors and stick two Xeon Nehalem processors in it. Could you use this system as a desktop PC or is this useless or even impossible? It's more hypothetical question if Windows 7 would support such a set-up. I know you could just take an i7, but wouldn't two of those processors be a whole lot more awesome? Like the previous generation Skulltrails? The idea would be to have a motherboard like this ASUS Z8NA-D6C Dual LGA 1366 Intel 5500 ATX and two Xeons (since I don't think i7's could be used) Intel Xeon E5405 Harpertown to run something like Windows 7 Ultimate.

    Read the article

  • Fried graphics card, how to proceed ?

    - by user19496
    Motherboard: Biostar TPower I45 I fried my graphics card (white smoke), by removing the cable marked PCI-E from the card, and then booting. Removed the graphics card, and now the machine is booting, and I can ping it. However I have no possibility to see what is actually happening, because I can't attach a monitor. Can I workaround the lack of monitor in some way, just to see if the motherboard is fine, attach a cable and telnet in or any other way ? Or, do I have to buy and install a new graphics card to be sure ?

    Read the article

  • Windows 2000 Inaccessible Boot Device

    - by Foo_Chow
    I am working with a machine that had its motherboard die. The machine is running Windows 2000 for legacy software. After the motherboard died I used disk2vhd to perform a physical to virtual transfer. The drive data seemed to copy over to the vhd file well. However, whenever i try to boot I get a message saying Inaccessible Boot Device So far I have tried several things to fix it. fixMBR fixBoot chkdsk windows 2000 automated repair Also, I have attempted to open the registry of the vhd without any success. There is another fix that i have seen suggested that requires editing the registry. Is it possible to open a Windows 2000 hive in another OS or another copy of Windows 2000? One other thing to note is that the error appears in all of Virtual PC 2007, Hyper-V and VMWare Player. Does anyone know how to get past this?

    Read the article

  • USB mouse disconnecting and reconnecting randomly and often

    - by Marc
    Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

    Read the article

  • Can't find onboard NIC with windows server 2008

    - by Sanarothe
    Hi. I'm trying to setup a windows server, but I can't seem to get it to install ethernet drivers :( motherboard is ms-6743 chipset 82865g/pe/p(intel) The MSI drivers specifically for this motherboard are bad links. Not surprising... MSI is rarely helpful. Sisoft Sandra doesn't see any network devices, and all of my leads to drivers have reported that there is no network adapter to install a driver for. The light is ON on the mobo, the onboard setting in bios is ON and the computer worked just fine with a standard install of windows 7 about a month ago. I don't know what to do :(

    Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >