Search Results

Search found 5390 results on 216 pages for 'ssl vpn'.

Page 35/216 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• Setting up a VPN connection to Amazon VPC - routing

  - by Keeno

  I am having some real issues setting up a VPN between out office and AWS VPC. The "tunnels" appear to be up, however I don't know if they are configured correctly. The device I am using is a Netgear VPN Firewall - FVS336GV2 If you see in the attached config downloaded from VPC (#3 Tunnel Interface Configuration), it gives me some "inside" addresses for the tunnel. When setting up the IPsec tunnels do I use the inside tunnel IP's (e.g. 169.254.254.2/30) or do I use my internal network subnet (10.1.1.0/24) I have tried both, when I tried the local network (10.1.1.x) the tracert stops at the router. When I tried with the "inside" ips, the tracert to the amazon VPC (10.0.0.x) goes out over the internet. this all leads me to the next question, for this router, how do I set up stage #4, the static next hop? What are these seemingly random "inside" addresses and where did amazon generate them from? 169.254.254.x seems odd? With a device like this, is the VPN behind the firewall? I have tweaked any IP addresses below so that they are not "real". I am fully aware, this is probably badly worded. Please if there is any further info/screenshots that will help, let me know. Amazon Web Services Virtual Private Cloud IPSec Tunnel #1 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Your Customer Gateway must be configured with a tunnel interface that is associated with the IPSec tunnel. All traffic transmitted to the tunnel interface is encrypted and transmitted to the Virtual Private Gateway. The Customer Gateway and Virtual Private Gateway each have two addresses that relate to this IPSec tunnel. Each contains an outside address, upon which encrypted traffic is exchanged. Each also contain an inside address associated with the tunnel interface. The Customer Gateway outside IP address was provided when the Customer Gateway was created. Changing the IP address requires the creation of a new Customer Gateway. The Customer Gateway inside IP address should be configured on your tunnel interface. Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.42 Inside IP Addresses - Customer Gateway : 169.254.254.2/30 - Virtual Private Gateway : 169.254.254.1/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: To route traffic between your internal network and your VPC, you will need a static route added to your router. Static Route Configuration Options: - Next hop : 169.254.254.1 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. IPSec Tunnel #2 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.46 Inside IP Addresses - Customer Gateway : 169.254.254.6/30 - Virtual Private Gateway : 169.254.254.5/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: Static Route Configuration Options: - Next hop : 169.254.254.5 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. EDIT #1 After writing this post, I continued to fiddle and something started to work, just not very reliably. The local IPs to use when setting up the tunnels where indeed my network subnets. Which further confuses me over what these "inside" IP addresses are for. The problem is, results are not consistent what so ever. I can "sometimes" ping, I can "sometimes" RDP using the VPN. Sometimes, Tunnel 1 or Tunnel 2 can be up or down. When I came back into work today, Tunnel 1 was down, so I deleted it and re-created it from scratch. Now I cant ping anything, but Amazon AND the router are telling me tunnel 1/2 are fine. I guess the router/vpn hardware I have just isnt up to the job..... EDIT #2 Now Tunnel 1 is up, Tunnel 2 is down (I didn't change any settings) and I can ping/rdp again. EDIT #3 Screenshot of route table that the router has built up. Current state (tunnel 1 still up and going string, 2 is still down and wont re-connect)

  Read the article

• How to share internet over VPN and inside a virtual machine (Windows)?

  - by mountrix

  ` My final goal is to have a virtual machine at work in which anything that happen inside (tcp, udp, ping, ...) will use the Internet connection of a computer at home. So, if inside this VM should I open an Internet browser to a site such as "show my IP", my home IP should be printed. I am also looking for a way to debug/develop a software inside this VM, but I would like to tunnel only the connections of this software, not the full graphical interface, this is why a Remote Desktop solution won't fit me. The connection between the both computer should be secured somehow, like in a SSH tunnel. This ultimately should allow me to have a portable VM in which I can connect to whatever networks I have access at home, in a secure way. This is my configuration: At work, I have a LAN-connected desktop computer, with Windows 7 Professional Edition as a host [computer W] On this same computer, I have a Virtual Box machine running Windows XP [computer V] At home, I have a laptop computer, running Windows 7 Home Edition [computer H] This laptop is connected to a Livebox 2 broadband modem by Wifi. What I am trying to do is to sit at work in front of the virtual machine [V], and connect to a webpage as if the request was issued from the laptop [H] at home, and the data should be securely tunneled between the both. But if I am using internet directly inside [W], it should use the normal LAN interface at work. To achieve my goal, I first try using VPN, than SSH tunneling, without success. I first tried to install Teamviewer between [W] and [H]. This is working fine, I can send files, share desktop, etc. Teamviewer has a VPN mode that creates a new VPN network interface with its own IP, both on computer [W] and [H]. This allowed me to connect [H] as a network computer inside [W] and I was able to share files, but not to share Internet. At this point, I tried to use from [W] the Internet as if I was at home. I setup a route (using route add from command line in [W]) in order to instruct each packet going to a given website to pass by the new VPN interface on [W], with the hope it will be forwarded to [H], but the webpage was simply inaccessible. I then tried to setup a Windows VPN connection between [W] and [H], using the Windows 7 VPN feature. [H] was the server and [W] the client. But it failed: I got the "Unable to join a remote PC while trying to VPN" 720 Error when I was setting up the client on [W]. I think the problem is the Livebox 2 that could blocks the packets. But I am not sure of this: 1) with Teamviewer it works fine, 2) Livebox 2 has a configuration page for port mapping that gives the proper configuration to map VPN ports as an example so I guess that it should allow it, 3) I opened the ports 1723 (TCP) and 500 (UDP) according to some forums. Virtual box has a network configuration parameter in which I can use the VPN network interface created by Teamviewer as a bridged connection. This is suppose to work in the sense that all packets issued by the virtual machine [V] is supposed to go directly to [H]. But I had no internet connection inside [V]. Using the NAT mode, [V] has internet. For me this is the feature that I look for: filtering all connections from the virtual box application to the VPN network interface, and the remaining should use the normal LAN interface. Apart from the build-in feature of VBox, I even do not know if it is possible to route the packet from a given application to a given interface. Finally I tried also SSH tunneling, but this is not the solution I looked for. Using an external SSH server (Linux), I was able to create a localhost connection on [W] (or [V]), using something like 'ssh -N -D server[H]' in order to allow a web browser located in [W] to connect to any website using the SOCKS 5 proxy created locally (SOCKS is a build-in feature of SSH). But repeating the same operation on windows, using a windows SSH server inside [W] (I tried freeSSHd), it failed: SFTP worked, but not the SOCKS tunneling, it was like the browser in [H] did not find internet. Finally only Teamviewer looked able to create a VPN between [W] and [H], but I am not able to use it, as I want, I mean using the Internet connection of [H] sitting in front of [W]. I also tried to bridge the VPN interface and the wifi interface inside [H], but it blocked my laptop, and I tried also the Internet Connection Sharing, trying to share on [H] the wifi connection over the VPN interface. This fails also, but it seems because Teamviewer actually use the wifi interface to be able to provide the VPN link, so I guess I am creating a recursive loop. I do not know what to try next... Thank you for any advice!!

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Fake ssl cetificate for development

  - by Zerotoinfinite

  Hi, I am using asp.net 3.5 with c#, I want to develop website with SSL transaction. But before Developing the site I want to work with SSL to learn more from it. Please let me know from where I can get the dummy SSL or Fake SSL so that I could do the development work. Thanks in advance

  Read the article

• Accessing MySQL server via VPN in python

  - by user210481

  Hi I have a MySQL server that I need access through a VPN. I use MySQLdb package to access MySQL server in Python. When I can access the server without VPN, it works fine, but when I'm at certain locations, I need to connect through VPN. My computer is connected to the VPN and I can access the database through PHPMyAdmin, but MySQLdb gives me an error message: OperationalError: (2003, "Can't connect to MySQL server on 'MY_IP' (10061)") Any ideas on why it's not working? Thanks

  Read the article

• Cisco PIX to Juniper Netscreen Policy-based VPN fails Phase 2 Proposal

  - by elint

  I've followed the instructions to configure a VPN between a netscreen device and a Cisco PIX as directed by Cisco's [netscreen to PIX VPN]http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801c4445.shtml article. The only differences are that I'm running PIX 6.3(5) and Juniper Netscreen 6.1.0r2.0 (Firewall+VPN). I followed both configurations exactly, and when I try to connect, the Juniper returns with: 2010-02-21 12:54:28 information IKE: Removed Phase 2 SAs after receiving a notification message. 2010-02-21 12:54:28 information IKE pix_public_IP: Received a notification message for DOI 1 14 NO-PROPOSAL-CHOSEN. 2010-02-21 12:54:28 information IKE pix_public_IP Phase 2: Initiated negotiations. On the Netscreen, I've created a Phase 2 Proposal called ToCorpOffice using DH Group#2, 3DES-CBC, and SHA-1, and when configuring the AutoKey IKE, I chose ToCorpOffice and removed all other transforms. I believe I've configured the same on the PIX with: sysopt connection permit-ipsec crypto ipsec transform-set mytrans esp-3des esp-sha-hmac crypto map mymap 10 ipsec-isakmp crypto map mymap 10 match address nonat crypto map mymap 10 set pfs group2 crypto map mymap 10 set peer netscreen_public_ip crypto map mymap 10 set transform-set mytrans crypto map mymap interface outside Saved that and rebooted, so here's the cryptomap info: PIX-FW1# show crypto map Crypto Map: "mymap" interfaces: { outside } Crypto Map "mymap" 10 ipsec-isakmp Peer = netscreen_public_ip access-list nonat; 1 elements access-list nonat line 1 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 (hitcnt=0) Current peer: netscreen_public_ip Security association lifetime: 4608000 kilobytes/28800 seconds PFS (Y/N): Y DH group: group2 Transform sets={ mytrans, } PIX-FW1# Any idea why I'm getting a NO-PROPOSAL-CHOSEN error?

  Read the article

• squid ssl bump sslv3 enforce to allow old sites

  - by Shrey

  Important: I have this question on stackoverflow but somebody told me this is more relevant place for this question. Thanks I have configured squid(3.4.2) as ssl bumped proxy. I am setting proxy in firefox(29) to use squid for https/http. Now it works for most sites, but some sites which support old SSL proto(sslv3) break, and I see squid not employing any workarounds for those like browsers do. Sites which should work: https://usc-excel.officeapps.live.com/ , https://www.mahaconnect.in As a workaround I have set sslproxy_version=3 , which enforces SSLv3 and above sites work. My question: is there a better way to do this which does not involve enforcing SSLv3 for servers supporting TLS1 or better. Now I know openssl doesn't automatically handle that. But I imagined squid would. My squid conf snipper: http_port 3128 ssl-bump generate-host-certificates=on dynamic_cert_mem_cache_size=4MB cert=/usr/local/squid/certs/SquidCA.pem always_direct allow all ssl_bump server-first all sslcrtd_program /usr/local/squid/libexec/ssl_crtd -s /usr/local/squid/var/lib/ssl_db -M 4MB client_persistent_connections on server_persistent_connections on sslproxy_version 3 sslproxy_options ALL cache_dir aufs /usr/local/squid/var/cache/squid 100 16 256 coredump_dir /usr/local/squid/var/cache/squid strip_query_terms off httpd_suppress_version_string on via off forwarded_for transparent vary_ignore_expire on refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 UPDATE: I have tried compiling squid 3.4.5 with openssl 1.0.1h . No improvements

  Read the article

• Issue configuring Oracle database for SSL

  - by Santhosha Kaldambe

  Hello, I want to setup Oracle for SSL communication. I am not using SSL authentication for database user. As first requirement, generated self signed certificate using OpenSSL and added certificate to wallet. The wallet location is specified in server configuration. Created listener and it is starting however it does not provide any service. The default listener (non SSL) is working fine. When I execute LSNRCTL.EXE status SSLLISTENER it gives below output. STATUS of the LISTENER Alias SSLLISTENER Version TNSLSNR for 32-bit Windows: Version 11.1.0.6.0 - Production Start Date 14-NOV-2009 01:47:08 Uptime 16 days 22 hr. 14 min. 3 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File C:\app\Administrator\product\11.1.0\db_1\network\admin\listener.ora Listener Log File c:\app\administrator\diag\tnslsnr\\ssllistener\alert\log.xml Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=tcps)(HOST=)(PORT =2484))) The listener supports no services The command completed successfully Here is exact content of various files after configuration. 1) File Name: tnsnames.ora ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) 2) File Name: sqlnet.ora SSL_VERSION = 0 NAMES.DIRECTORY_PATH= (TNSNAMES, EZCONNECT) sqlnet.authentication_services= (NONE) tcp.validnode_checking = no tcp.invited_nodes=(PS0803.oraebs.com,PS2948,PS5098) SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) 3) File Name: listener.ora SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521)) ) (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) ) SSLLISTENER = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCPS)(HOST = )(PORT = 2484)) ) Thanks Santhosh

  Read the article

• How to set up ProxMox 1.9 on VPN?

  - by Gnudiff

  Disclaimer: I have only rudimentary knowledge of VPNs. I would love to learn about them properly, however, at the moment I really need to make stuff work on short notice. I am trying to set up a ProxMox virtualization platform in an existing network. The network currently consists of several servers which have VMWare free edition. There is some sort of VPN defined in switch. In order for VMWare management interface to be accessible, there needs to be ticked a checkbox in the network settings for VPN and entered the VPN id. I didn't notice any such configuration option during ProxMox installation, so my Proxmox VE on the same physical server, using same manual IP settings (ip/nm/gw), is not accessible. As I understand I should touch the Proxmox's underlying Debian config in /etc/network/interfaces, but I have no idea, what should I aim for: do I specify the settings for eth0, do I make a virtual interface? How to make it accessible for both ProxMox VE and underlying future VMs? I read the ProxMox installation guide, but unfortunately it presumes better understanding of VPNs than I have. A config template or similar would be appreciated. Thanks in advance.

  Read the article

• Providing access to a Samba server for VPN clients

  - by Kamil Kisiel

  We have some Windows users that connect to our network via VPN from home. They need to be able to connect to our Samba server and access a mapped network drive just as they do as when they are on our LAN. The complication is that VPN clients are placed on a subnet other than our office LAN, and behind a firewall. What's the easiest way for me to allow them to still connect to the network share? The solutions I've currently seen involve setting up a WINS server for name resolution purposes and then tunnelling a bunch of the NetBIOS stuff through the firewall. However that means I'd have to set up the VPN DHCP server to hand out the WINS address, something I'm not even sure is possible on the Cisco hardware we have. I'm thinking there must be an easier way. Should I use an LMHOSTS file? Or just map by IP address? Also, I'm not terribly familiar with Windows networking, so which ports would I need to pass through my firewall in order to get the file sharing through?

  Read the article

• nginx reverse ssl proxy with multiple subdomains

  - by BrianM

  I'm trying to locate a high level configuration example for my current situation. We have a wildcard SSL certificate for multiple subdomains which are on several internal IIS servers. site1.example.com (X.X.X.194) -> IISServer01:8081 site2.example.com (X.X.X.194) -> IISServer01:8082 site3.example.com (X.X.X.194) -> IISServer02:8083 I am looking to handle the incoming SSL traffic through one server entry and then pass on the specific domain to the internal IIS application. It seems I have 2 options: Code a location section for each subdomain (seems messy from the examples I have found) Forward the unencrypted traffic back to the same nginx server configured with different server entries for each subdomain hostname. (At least this appears to be an option). My ultimate goal is to consolidate much of our SSL traffic to go through nginx so we can use HAProxy to load balance servers. Will approach #2 work within nginx if I properly setup the proxy_set_header entries? I envision something along the lines of this within my final config file (using approach #2): server { listen Y.Y.Y.174:443; #Internally routed IP address server_name *.example.com; proxy_pass http://Y.Y.Y.174:8081; } server { listen Y.Y.Y.174:8081; server_name site1.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8081; } server { listen Y.Y.Y.174:8081; server_name site2.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8082; } server { listen Y.Y.Y.174:8081; server_name site3.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer02:8083; } This seems like a way, but I'm not sure if it's the best way. Am I missing a simpler approach to this?

  Read the article

• Exchange 2010 POP3/IMAP4/Transport services complaining that they can't find SSL certificate after blue screen

  - by Graeme Donaldson

  We have a single-server Exchange 2010 setup. In the early hours of this morning the server had a blue screen and rebooted. After coming back up the POP3/IMAP4 and Transport services are complaining that they cannot find the correct SSL certificate for mail.example.com. POP3: Log Name: Application Source: MSExchangePOP3 Date: 2012/04/23 11:45:15 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. SSL or TLS encryption can't be made to the POP3 service. IMAP4: Log Name: Application Source: MSExchangeIMAP4 Date: 2012/04/23 08:30:44 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. Neither SSL or TLS encryption can be made to the IMAP service. Transport: Log Name: Application Source: MSExchangeTransport Date: 2012/04/23 08:32:27 AM Event ID: 12014 Task Category: TransportService Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: Microsoft Exchange could not find a certificate that contains the domain name mail.example.com in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Default EXCH01 with a FQDN parameter of mail.example.com. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. The odd part is that Get-ExchangeCertificate show the cert as enabled for all the relevant services, and OWA is working flawlessly using this certificate. [PS] C:\Users\graeme\Desktop>Get-ExchangeCertificate Thumbprint Services Subject ---------- -------- ------- XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX ....S. CN=exch01 YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY ....S. CN=exch01 ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ IP.WS. CN=mail.example.com, OU=Domain Control Validated, O=mail.exa... Here's the certificate in the computer account's personal cert store: Does anyone have any pointers for getting POP3/IMAP4/SMTP to use the cert again?

  Read the article

• SSL in IIS 7 on a subdomain in a web farm

  - by justjoshingyou

  I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

  Read the article

• VPN Error 691 but server says authenticated on server

  - by Andy

  Hello all, I have a problem with a vpn connection on Windows XP SP3 that appears to be related to an account (maybe privilleges or an option that I have missed). When connecting using my account, which is a domain administrator account it will connect to through the vpn fine. However, using an account created for another person they receive Error 691: Username or Password is not valid for this domain. On the domain controller (windows 2003) I see a logon successful message: User DOMAIN\user was granted access. Fully-Qualified-User-Name = int.company.net.au/People/Management/User NAS-IP-Address = 10.30.0.3 NAS-Identifier = not present Client-Friendly-Name = MelbourneCore Client-IP-Address = Router-ip Calling-Station-Identifier = not present NAS-Port-Type = Virtual NAS-Port = 77 Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = undetermined Policy-Name = Remote VPN Access Authentication-Type = MS-CHAPv1 EAP-Type = Does anyone have any ideas as to where else I should look for finding a solution? If i use the wrong password it gives a logon failure error in the event viewer. Also removing them from the remote access group gives a logon failure error. Nothing appears in the event viewer on the local machine. In the past all that is required is to add them into our Remote Access Users group. Any help?

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Changing Mac OS X 10.6 Routing after VPN'd In

  - by Matt Rogish

  I have a coffee shop around the corner that I use to do some work when I want to get away from home. They offer free wi-fi and I then use my Mac 10.6 VPN to log into my work network. I have "Send all traffic over VPN connection" checked. Before, their network was 10.0.0.x. I think they got a new router because it's now 192.168.2.x However, this interferes with one of the subnets at work so now I can't visit 192.168.2.x at work. So: 1) Office network: VPN gives IPs as 192.168.1.x. Another network is 192.168.2.x 2) Coffee network: Gives IPs as 192.168.2.x I think if I set a route to send all 2.x traffic over the tunnel, it would blow up my routing to their system, right? What should I do? I know the individual IPs of the servers I want... Maybe I could add each one, or can I add all of them minus the default gateway of their router? How do I set that up "temporarily" in my Mac? Thanks!!

  Read the article

• Checkpoint VPN-1 R60 and Windows 7 64 Bit Client

  - by Mohit

  As per my knowledge of checkpoint VPN-1. My company is using checkpoint VPN-1 R 60 ( I guess as I dont know how to check server version) Firewall(VPN Server). Now the problem is that I installed Windows 7 64 bit. But, after my research I found that there are not even one client (SecuRemote/SecuClient) for Win7 64 bit, when Firewall or server is R60. I thought of some open source solutions. Can you guys please suggest me some with the configuration required. As of now, I know the IP of the server. I know my username and password using which I connect and that is not my domain password. that i can confirm to you guys. I am not a network guy. I am more of a developer. But, I need some help in this.So, let me know if I can provide you more details. Please please i need urgent help on this.

  Read the article

• Apache: rewrite port 80 and 443 - multiple SSL vhosts setup

  - by Benjamin Jung

  SETUP: multiple SSL domains are configured on a single IP, by using vhosts with different port numbers (on which Apache listens) Apache 2.2.8 on Windows 2003 (no comments on this pls) too many Windows XP users so SNI isn't an option yet There may be reasons why it's wrong to use this approach, but it works for now. vhosts setup: # secure domain 1 <VirtualHost IP:443> SSL stuff specifying certificate etc. ServerName domain1.org </VirtualHost> # secure domain 2 <VirtualHost IP:81> SSL stuff for domain2.org ServerName domain2.org </VirtualHost> GOAL: Some folders inside the domain2.org docroot need to be secure. I used a .htaccess file to rewrite the URL to https on port 81: RewriteEngine On RewriteCond %{SERVER_PORT} !^81$ RewriteRule (.*) https://%{HTTP_HOST}:81%{REQUEST_URI} [R] Suppose I put the .htaccess in the folder 'secfolder'. When accessing http://domain2.org/secfolder this gets succesfully rewritten to https://domain2.org:81/secfolder. ISSUE: When accessing https://domain2.org/secfolder (without port 81), the certificate from the first vhost (domain1.org) is used and the browser complains that the site is insecure because the certificate is not valid for domain2.org. I thought that RewriteCond %{SERVER_PORT} !^81$ would also rewrite https://domain2.org to https://domain2.org:81, but it doesn't. It seems that the .htaccess file is not being used at all in this case. At this point I am not sure how to apply a RewriteRule to https://domain2.org. I tried creating an additional vhost for domain2 on port 443 before the one for domain1.org, but Apache seems to choke on that. I hope someone of you has an idea how to approach this. TIA.

  Read the article

• VPN from Windows XP to OpenSwan: correct setup?

  - by Gnudiff

  Main question is what I am doing wrong in my OpenSwan or L2TP client setup? I am trying to create a Linux OpenSwan VPN connection from Windows XP machine, using preshared key and the builtin Windows XP L2TP IPsec option. I have followed the instructions in Linux Home networking Wiki for setting up OpenSwan and a guide to making it work with the Windows XP client, but am now stuck. The net setup is as follows: [my windows client, private IP A]<->[f/wall B]<-internet->[g/w X]<->[Linux OpenSwan server Y] A - private subnet /24 B - internet address X - internet address /24 Y - internet address on same subnet as X What I essentially want is for computer with A address to feel and work, as if it was in X subnet for purposes of outgoing and incoming TCP and UDP connections. My OpenSwan setup is as follows: /etc/ipsec.conf (AAA and YYY indicates ip address parts of A and Y addresses): conn net-to-net authby=secret left=B leftsubnet=AAA.AAA.AAA.0/24 leftnexthop=%defaultroute right=Y rightsubnet=YYY.YYY.YYY.0/24 rightnexthop=B auto=start the secret in /etc/ipsec.secrets is listed as: B Y : PSK "0xMysecretkey" where B & Y stand for respective IP adresses of gateway B and linux server Y My L2TP WinXP setup is: IP of destination: Y don't prompt for username security options: typical, require secured pass, don't require data encryption, IPSec PSK set to 0xMysecretkey networking options: VPN Type: L2TP IPSec VPN; TCPIP protocol (with automatic IP address assignment) and QOS packet schedulers enabled The error I get from Windows client is 789: "error during initial negotiation"

  Read the article

• Apahe configuration with virtual hosts and SSL on a local network

  - by Petah

  I'm trying to setup my local Apache configuration like so: http://localhost/ should serve ~/ http://development.somedomain.co.nz/ should serve ~/sites/development.somedomain.co.nz/ https://development.assldomain.co.nz/ should serve ~/sites/development.assldomain.co.nz/ I only want to allow connections from our local network (192.168.1.* range) and myself (127.0.0.1). I have setup my hosts file with: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 development.somedomain.co.nz 127.0.0.1 development.assldomain.co.nz 127.0.0.1 development.anunuseddomain.co.nz My Apache configuration looks like: Listen 80 NameVirtualHost *:80 <VirtualHost development.somedomain.co.nz:80> ServerName development.somedomain.co.nz DocumentRoot "~/sites/development.somedomain.co.nz" DirectoryIndex index.php <Directory ~/sites/development.somedomain.co.nz> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost localhost:80> DocumentRoot "~/" ServerName localhost <Directory "~/"> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <IfModule mod_ssl.c> Listen *:443 NameVirtualHost *:443 AcceptMutex flock <VirtualHost development.assldomain.co.nz:443> ServerName development.assldomain.co.nz DocumentRoot "~/sites/development.assldomain.co.nz" DirectoryIndex index.php SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /Applications/XAMPP/etc/ssl.crt/server.crt SSLCertificateKeyFile /Applications/XAMPP/etc/ssl.key/server.key BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 <Directory ~/sites/development.assldomain.co.nz> SSLRequireSSL Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> </IfModule> http://development.somedomain.co.nz/ http://localhost/ and https://development.assldomain.co.nz/ work fine. The problem is when I request http://development.anunuseddomain.co.nz/ or http://development.assldomain.co.nz/ it responds with the same as http://development.somedomain.co.nz/ I want it to deny all requests that do not match a virtual host server name and all requests to a https host that are requested with http PS I'm running XAMPP on Mac OS X 10.5.8

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• Poor SSL performance with vsftpd

  - by petrus

  I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

  Read the article

• Copying compressed files from Server 2008 R2 network share to XP client via VPN fails

  - by Dejan Janjuševic

  At the first sight the question looks similar to this one. I have experienced an odd behavior while trying to copy a certain file from Windows Server 2008 R2 network share to Windows XP Professional client via VPN. The VPN was set up using RRAS on the server machine. I will try to provide as much informations as possible in order to make the issue more clear. When trying to copy the compressed file sized ~2.5 MB (via Explorer or CMD, doesn't matter), the process stalls after some 20%, producing an error message after few seconds: Cannot copy filename: The specified network name is no longer available. If i start the command ping -t 192.168.2.1 (where the IP address specified belongs to the server) side by side with the copy command, I can clearly see that the ping command times out for few seconds as the copy process stalls. When this happens all network activities are frozen. After a few seconds, the network recovers, ping continues to run normally, however the copy process stands still before it displays the above error message. Copying other files (I tried 4-5 files), of which some are larger and some are smaller, succeeds. Seems to me that I can copy all uncompressed files. As soon as I try to copy an archive, the process freezes. Even a 707 KB large archive can't be copied. I can only reproduce this behavior on 2 machines, both Windows XP Professional, one is w/ SP2 and the other w/ SP3. Other XP clients don't have this problem, neither do Windows 7 clients. If I connect to the server using Remote Desktop Connection without using VPN from either of these 2 machines (using the same user account), I can copy anything I want normally, even these "problematic" files. Does anyone have any clue about what could possibly be going on?

  Read the article

• Cisco ASA dropping IPsec VPN between istself and CentOS server

  - by sebelk

  Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >