Search Results

Search found 11512 results on 461 pages for 'usb mass storage'.

Page 35/461 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• diskmgmt.msc: Cannot delete volume from USB

  - by Notinlist

  I have an USB drive with about 8GB of size. It has a single partition of size 169MB. Don't know why, I got it that way. I wanted to delete this small (FAT32) partition and create a single NTFS volume on it. First, I noticed that the "Delete volumme" option is disabled (grayed out). I then tried "Change drive letter and paths..." and removed "F:", that way I made sure that there are no open files on it. The "Delete volume" was still disabled. Then I got suspicious, and right clicked on the "Unallocated" area and I noticed that I did not have any useful option. All "New * volume" items are disabled. I exited from diskmgmt.msc, ran a cmd.exe with administrator privileges, ran the diskmgmt.msc from it, same experiences. Why can't i do anything with this disk? I've read some advices about downloading some alternative free software, but I rather not do it if possible. I still hope that Windows 7 Enterprise 64bit alone can reinitialize an USB drive without external help. I also cannot do anything with my other 8GB pendrive. It's all an NTFS volume, I tried to delete it, but the option is disabled here too. Maybe I have some settings somewhere that prevents my from partitioning USB disks. (I have the freedom to remove my D: partition which is the second - not counding the "System reserved" - on my SSD disk.)

  Read the article

• Make UEFI, GPT, Bootloader, SSD, USB, Linux and Windows work together

  - by user129552

  I like to use the latest hardware and the latest software; thus I have a Laptop (Lenovo X220) with UEFI instead of BIOS an SSD instead of an HDD GPT partitioning scheme instead of MBR USB to boot from instead of optical disks. I need to use both Windows and Linux. I tried to make them work alongside, but I didn't succeed. Most Linux distribution isos don't even really work on UEFI systems booted from USB. (Not even the self-claimed cutting-edge Fedora. I also tried Linux Mint Debian Edition and Sabayon Linux (according to this guide) which did not work. Only Ubuntu worked for me. I first installed Windows 8 which created sda1: Recovery, sda2: EFI system, sda3: msftres, sda4: NTFS Windows. Windows worked without a problem. I then created sda5: linux-swap and installed Ubuntu into sda6: btrfs. After rebooting, I was not presented GRUB2 as expected, but instead my system just booted into Ubuntu. I could no longer access Windows. After fixing dpkg in btrfs Ubuntu, I followed the Ubuntu documentation on UEFI booting. The result left me with a broken GRUB2, but interestingly, when I wanted to select the device to boot from, I was not only presented the internal SSD, an attached USB device, or LAN, but also Grub2 (broken), Ubuntu and Windows. The result is not very satisfying to me. What would I have to do to fix everything? Or differently asked, what operating system should I install at what point given my possibilities and requirements, so that I have a working bootloader in my UEFI GPT system which presents me a working Linux and Windows.

  Read the article

• Short, intermittent USB port timeouts

  - by jacobsee

  I have a data acquisition application controlled by a Windows PC. I am using an Intel Desktop Board DH67CL motherboard. This has 6 USB2 ports along with 2 of the new blue USB3 ports. The DAQ instrument connects via USB to the computer. Roughly once every day or two there is a short communication glitch with the USB that causes the instrument to disconnect briefly and then reconnect. This is logged so I know whenever it happens. Occasionally it will cause the data acquisition to stop. I've verified that the glitches will go away if I use the USB3 ports, or if I use a PCI add-on card with USB ports. So it seems that there is something going on with these built-in USB2 ports on this motherboard. I haven't yet had a chance to test with other motherboards. My question: what could be causing these glitches and how to get rid of them for this board, or is there a better motherboard to use? We have standardized on the DH67CL because it's inexpensive, has 3 PCI slots that we need, and is readily available. We don't need the power of higher-end server boards but reliability is important. Thanks. Update: This problem has been reproduced many times on different hardware, though we always use the same model of motherboard (DH67CL) and power supply (Antec EA-430D). I don't think the power requirements are very high but will check on that.

  Read the article

• No partition on USB Flash Drive?

  - by Skytunnel

  A friend gave me a corrupted USB memory stick to try recovery data from. But I've had some unusual results, so thought I'd share to see if anyone is familiar with this problem... First off I just tried opening from my own PC. Windows prompted to Format the drive, which I of course declined Downloaded TestDisk to anaylsis the drive. And right away I noticed something strange, on the listed drives it comes up as Disk /dev/sdc - 6144 B - USB Flash Drive That's right, the first USB flash drive smaller than a floppy disk!? Moving on anyway... first anaylsis comes up with: Partition sector doesn't have the endmark 0xAA55 TestDisk's Quick Search gave no results, moved on to Deeper Search: No partition found or selected for recovery This left me stumped. I tired a couple of other programs with no success I did manage to get a backup image, but it was just as small as TestDisk indicated, so nothing of use on it After a few hours trying various suggestions from other sources, I gave in and just tried formatting the drive. But returned the message: Windows was unable to complete the format. From googling that, the suggestion was to delete the partition. But there is no partition to delete in this case. most recently I've tried formatting from cmd, and got this result: Format D: /FS:FAT32 The type of the file system is RAW The new file system is FAT32 Verifying 0M 11 bad sectors were encountered during the format. These sectors cannot be guaranteed to have been cleaned The volume is too small for FAT32 Anyone got any suggestions? UPDATE: As per suggestion from @Karen, I tried running a CLEAN from DISKPART, results as follows DiskPart has encountered an error: The request could not be preformed because of an I/O device error.

  Read the article

• Bootable ISO to USB stick xp quickest method

  - by brux

  My dog took a leak on my PC when I went out (ye funny), now it reandomly restarts - I'm convinced the HDD is failing because the Windows seagate diagnostic program fails on a few tests. I want to run this prior to windows in an attempt to try and recover sectors, the program includes an iso which can be written to cd and booted, but i dont have any cd's. I tried using unetbootin to create the bootable usb from the iso file (SeaToolsDOS222ALL.576.ISO) but it doesnt work. When i boot from the usb hdd unetbootin loads with "default" in the menu. No joy booting though. I checked the usb hdd in windows and all the files are there, extracted from the iso file, wont boot though. Any ideas? Im using windows xp. More info - when the computer restarts (like i just did now) it constantly reaches the end of POST and then restarts in infinite loop. If I pull the power cable out it will get back into windows, the longer i leave it between attempts, the longer I am able to stay in windows until it restarts. i.e if i leave the power cable out 5 minutes it will stay operable for longer than if i had left it out for only a few seconds.

  Read the article

• Would a USB hub work in reverse?

  - by Tim

  Imagine for a moment with a 4 port USB hub. Normally how this would work is the hub has one plug that goes to the computer, then 4 ports that you can plug in other things to (thumb drive, keyboard, mouse etc). I am wondering if I can use it in reverse. So I would have 1 keyboard going in to the hub, and then plug in male to male usb cables from the 4 ports to 4 different PCs, my aim is that when a key is pressed on the keyboard all 4 PCs will receive it as if the keyboard were plugged in to them. Does anyone know if this would work? And if not does anyone have any ideas how I could get the same effect? EDIT: So I am looking for more of a KVM switch type device rather than a USB hub. However all of the KVM switches I've found use some sort of mechanism to select which computer you'll be using. (some are physical switches / buttons, others do it via software "automatically" some how) However I need to have 1 keyboard hooked up to 2 computers and when I press a key on the keyboard I want the keypress to be sent to both computers simultaneously, not to one or the other. Does anyone know if KVMs with this feature exist?

  Read the article

• 100% CPU use when new usb device plugged in - services.exe / Windows Server 2003

  - by Will3265

  On my server I am trying to install a new usb drive but all that happens is that the system starts using huge amounts of processor cycles with services.exe. On closer inspection with process explorer there is a thread called umpnpmgr.dll using most of the services.exe processor time. I left it for a half hour and still nothing happened. Rebooted and tried again, same result. Tried a different usb drive, then a flash drive but still same issue. Tried updating driver but it said the update function was already in action. I have used process explorer to kill the thread now so the server can still perform its intended functions. Any device that was previously installed before this began happening will still work but any device new to the system will not. My question(s) is/are: Is there a way to manually install the device into the registry so Windows thinks it is a previously installed device? Or can this problem be repaired through anything other than a reinstall? To do a reinstall would mean backing up large amounts of data which is hard with a usb drive and insufficient space on all other network machines. Any help would be greatly appreciated. William

  Read the article

• Map /dev/bus/usb node to /sys node on Linux

  - by Cody Brocious

  I'm using libusb to find and access a USB device, but once I get the information I need from there, I need to map it to a /sys node. This could be to the actual USB bus it's on, the /sys/bus/usb-serial node (which is where I'm going to get eventually), or effectively anywhere else since I can walk the tree from there. I can get to a /dev/bus/usb node easily enough, but I'm a bit lost from there. What would be the best route to perform this mapping?

  Read the article

• Is it possible to have a USB to USB computer network?

  - by Ram Bhat

  Hey guys Was wondering if it was possible to have a USB to USB network for file transfer between two computers. As in there are two computers connected by a USB to USB connector and BOOM! Fast file transfer

  Read the article

• Controlling usb devices from a droid?

  - by user324721

  Anyone know where I can find information on how I can control the USB port on a Droid running Android 2.0? I want to know how to either initialize the USB port or send data across it vi a program. I want to be able to atatch a device to the USB port to act as a switch to control a microservo. So when I said "send data" across the port, I just need to be able to energize the transmit pin on the USB to turn the servo on. Thanks ahead, Tom

  Read the article

• Daisychain external USB drive to WD My Book World Edition (Blue rings)

  - by d03boy

  I recently bought a new My Book Essential 1TB (WDBACW0010HBK-NESN) to daisychain to my older My Book World Edition 500GB (blue rings) with one of the version 01.xx.xx firmwares. At first when I connected the USB drive to the MBWE, it showed up in the System Summary section of the administration page without any issue. I was able to set up a new share on the new drive. The administration website moved very, very slow though. The administration pages became nearly unresponsive during this setup process. Once the share was set up I could access the new share but again, it was very slow, now through Windows Explorer. I looked around the internet and it seems that this is caused by the USB drive being formatted with NTFS. I tried reformatting it (again, as NTFS) just to double check and the same problem occurred. I then tried FAT32 but realized it would only support files of approximately 2GB and that is not acceptable for me. I decided to try a firmware upgrade on the MBWE to version 02.00.19. The firmware upgrade completed successfully but now the MBWE does not display the USB drive in the System Summary like it did with the earlier firmware version. The USB drive works perfectly fine when connected directly to my computer. Is there a way to solve this issue?

  Read the article

• 19" Rackmountable fast storage arrays

  - by Eruditass

  I'm in need of some fast (15+ GB/s write) and somewhat large (50 TB+) storage subsystem with a standard storage interface. I'd prefer something other than Fibre Channel, which admittedly appears to be the most standard interface. RAID 5 is sufficient. What are the cheapest / smallest products from vendors to look at for building this subsystem? I've looked at DDN and TMS so far. Small: Under 20U Cheap: Under a million Edit: I'd really like to cut back costs as much as possible at the expense of capacity. How cheap can these bandwidth requirements be met?

  Read the article

• How do i use storage spaces?

  - by Lucas

  I am planning on building a new windows 2012 server for a client and I have no experience in doing so. I have built many linux servers for them and setting up software raid during the install is a trivial matter. I have been unable to confirm that the windows 2012 install process has an analogous process for setting up Storage Spaces during the install. Can Storage Spaces be used as an installation target (configured during setup?) Is it capable of mirror+stripe (RAID10)? We have not ordered the hardware yet, so I'm looking for clarification.

  Read the article

• How to speed up rsync?

  - by Jakobud

  I'm running rsync to sync a directory onto my external USB HDD. It's about 150 gigs of data. 50000+ files I would guess. It's running it's first sync at the moment, but its copying files at a rate of only 1-5 MB/s. That seems incredibly slow for a USB 2.0 enclosure. There are no other transfers happening on the drive either. Here are the options I used: rsync -avz --progress /mysourcefolder /mytargetfolder I'm running Ubuntu Server 9.10.

  Read the article

• Is there still a place for tape storage?

  - by Jon Ericson

  We've backed up our data on LTO tapes for years and it's a real comfort to know we have everything on tape. A sister project and one of our data providers have both moved to 100% disk storage because the cost of disk has dropped so much. When we propose systems to potential customers these days we tend to downplay or not mention our use of tape systems for data storage since it might seem outdated. I feel more comfortable with having data saved in two separate formats: disks and tape. In addition, once data is securely written to tape, I feel (perhaps naively) that it's been permanently saved. Not having to rely on a RAID controller to be able to read back data is another plus for me. Do you see a place for tape backup these days?

  Read the article

• How can I troubleshoot SSD disconnection problems on Windows 7?

  - by 0xC0000022L

  I have a small SSD (Transcend StoreJet TS256GESD200K) which I am using on several computers. The drive is formatted with NTFS and recently I started noticing disconnects. Normally one probably wouldn't notice (you don't even get the notification sound in Windows when it disconnects), but since I use USBDLM and run a VM from that SSD, I get to see this first-hand. How could I best figure out whether the problem is the hardware (SSD, USB socket, USB cable or something in the PC) or software? In short: how can I locate the source of the disruption so that I can work on removing the problem? Side-note: SMART status for the SSD is clean.

  Read the article

• How can I get data off of a damaged thumb drive?

  - by Lord Torgamus

  A guy I work with just came by to ask me about a damaged thumb drive/USB flash drive. Apparently his son dropped it on a hard surface and it won't power up anymore. They've tried plugging it into multiple machines without success, even though each port they tried was able to power other USB devices. He knows it's not a lost cause because a local tech store is offering to recover the data for $500, but he says they're not worth that much. I figured someone on SU would have an idea about this; he doesn't care about using the drive in the future, just wants to salvage a few files that would be a pain to recreate. Is this possible without advanced equipment, and if so, how? He said he already tried the advice on the Internet about typing in different drive letters and such, but that failed because there was no power going to the drive. He also said that he opened the case up at one point, but I'm not sure what, if anything, he did inside.

  Read the article

• LinqPad with Azure Table Storage

  - by Sarang

  LinqPad as we all know has been a wonderful tool for running ad-hoc queries. With Windows Azure Table storage in picture LinqPad was no longer in picture and we shifted focus to Cloud Storage Studio only to realize the limited and strange querying capabilities of CSS. With some tweaking to Linqpad we can get the comfortable old shoe of ad-hoc queries with LinqPad in the Windows Azure Table storage. Steps: 1. Start LinqPad 2. Right Click in the query window and select “Query Properties” 3. In The Additional References add reference to Microsoft.WindowsAzure.StorageClient, System.Data.Services.Client.dll and the assembly containing the implementation of the DataServiceContext class tied to the Windows Azure table storage. 4. In the additional namespace imports import the same three namespaces mentioned above. 5. Then we need to provide following details. a. Table storage account name and shared key. b. DataServiceContext implementing class in your code. c. A LINQ query. e.x.         var storageAccountName = "myStorageAccount";  // Enter valid storage account name         var storageSharedKey = "mysharedKey"; // Enter valid storage account shared key         var uri = new System.Uri("http://table.core.windows.net/");         var storageAccountInfo = new CloudStorageAccount(new StorageCredentialsAccountKey(storageAccountName, storageSharedKey), false);         var serviceContext = new TweetPollDataServiceContext(storageAccountInfo); // Specify the DataServiceContext implementation         // The query         var query = from row in serviceContext.Table                     select row;         query.Dump(); Thanks LinqPad! Technorati Tags: LinqPad,Azure Table Storage,Linq

  Read the article

• how to create a bootable usb on mac to install ubuntu into a formatted PC?

  - by kutayk

  hi I have a working MacBook Pro and a crashed Windows 7 PC. I was running Ubuntu on my PC but after a recurrent issue now I can't boot either OS. I would like to install only ubuntu to my PC and will make Windows 7 history for good. But I am a bit puzzled with cretatinf bootable usb options on the website. If I create a bootable USB on my MAc following the instructions for MAc OS, would it boot in A PC?

  Read the article

• How do I mount a USB floppy disk drive?

  - by Jocky B

  I have tried to mount my usb floppy disk drive in 11.04 Natty. So far I have managed to use the udisks --mount/dev/sdf command in terminal, but get a message that I have not stated a filetype john@john-desktop:~$ udisks --mount /dev/sdf Mount failed: Error mounting: mount: you must specify the filesystem type This is the result I get when trying to mount the usb floppy disk drive. Anyone know how to proceed?

  Read the article

• have to plug/un-plug usb devices on system booting?

  - by user866581

  it's so weired that i have to plug/unplug in my usb devices every time booting ubuntu. it happens for both installing ubuntu and booting ubuntu (10.10 and 11.10) the scenario is like: 1.bios checking - 2.grub start - 3.keyboard & mouse led OFF (black screen with a cursor on top-left) - 4.i plug/unplug in any usb devices - 5.everything is back to normal and ubuntu started it's really frustrating :( please advise the solution.

  Read the article

• Ubuntu in USB.. Boot from fixed HDD?

  - by Z9iT

  I am having Ubuntu 12.04 minimal installed on my USB pen-drive; which I use on several systems as portable OS. I was thinking to edit the boot parameters so that before the main Ubuntu OS is loaded, it shows an option to Boot from Hard Drive for 5 seconds, and then boots to Ubuntu. This way i'll be able to have an option to boot to the OS installed on the Hard-Drive, without removing or unplugging my ubuntu USB stick. How do I edit the boot parameters to achieve this?

  Read the article

• Why isn't persistence working on Lubuntu 12.04 Live-USB?

  - by Frodik

  I have used Universal-USB-Installer ever since to install different Linux versions to USB flash drive. But now with Lubuntu 12.04 even though I do the same process by selecting persistence file, it gets created but is never used in Lubuntu. Every time I boot into Lubuntu on flash, it is fresh new Lubuntu without my changes I did last time I have booted it. Anyone can help me or give me some hints ? Thanks in advance.

  Read the article

• Why is my Wacom Intuos tablet not detected?

  - by mjwittering

  I need a little help trying to install a Wacom Intuos tablet, model number CTL-480/S. My installation of Ubuntu 13.04, 64bit, doesn't seem to be able to detect the device. I've tried an few different USB ports on my machine and get the same result. I believe there is an issue because when I open the System Settings app from the launcher and browse to the Wacom Tablet section under hardware, it reports that there is 'No table detected'. When I use lsusb I can see the device is detected: Bus 003 Device 004: ID 056a:030e Wacom Co., Ltd I've also pulled the following from the syslog: Oct 16 16:51:05 earth kernel: [ 7062.388031] usb 3-5: new full-speed USB device number 4 using ohci_hcd Oct 16 16:51:05 earth kernel: [ 7062.611038] usb 3-5: New USB device found, idVendor=056a, idProduct=030e Oct 16 16:51:05 earth kernel: [ 7062.611042] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Oct 16 16:51:05 earth kernel: [ 7062.611045] usb 3-5: Product: Intuos PS Oct 16 16:51:05 earth kernel: [ 7062.611047] usb 3-5: Manufacturer: Wacom Co.,Ltd. Oct 16 16:51:05 earth mtp-probe: checking bus 3, device 4: "/sys/devices/pci0000:00/0000:00:02.0/usb3/3-5" Oct 16 16:51:05 earth mtp-probe: bus: 3, device: 4 was not an MTP device I'd really appreciate any suggestions to help debug and install this device.

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >