Search Results

Search found 15670 results on 627 pages for 'multi level'.

Page 351/627 | < Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >

• HPC Cluster planning workflow?

  - by Veronica

  After three days of intensive Google searching, I have not found any high-level workflow of how to build a low profile - cheap - computing cluster (we are not interested in HA yet). This is just a front-end plus a node for now. We want to start small with rockscluster, provide a web-based server for offering services, and then add nodes as our budget increases. We're small company, so we haven't enough human resources to implement it smoothly. Here are some facts about our environment: Our hardware is not constant (we will add nodes). Our workload will vary (in the order from 200Mb - 1Tb) Our software will change (scientific applications for data mining) Do you know any visual workflow, worksheet, chart, describing the general necessary steps to begin our cluster planning?

  Read the article

• Set security on pattern of sub folders (Server 2003)

  - by Mark Major

  I have a folder structure similar to the one shown below these paragraphs. How do I change security on every 'Photos' folder without clicking through each individually in Windows Explorer? There are about 50 top level folders (Bob, Jim, Eva, etc, etc) which have the same layout of folders inside. I am keen for any suggestions, either scripting or GUI. I am on Windows Server 2003. Cheap/free method would be good, as the company is part of a registered charity. Ideally I would like to do this via DFS path. E.G. \\mycompany.local\Shared\Staff\Bob\ Thanks for reading. Thanks for any info. Mark Bob Review Profile Photos Jim Review Profile Photos Eva Review Profile Photos

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• Directory and Sub Directory listing

  - by shekhar

  I am trying to list the directory name (only name, not full path) and sub directories (only name, not full path) inside it. There is only one level of sub directories. I used below script to do this: @echo off&setlocal enableextensions for /r "PATH" %%G in (.) do ( Pushd %%G for %%* in (.) do set MyDir=%%~n* echo %MyDir% popd ) endlocal&goto :eof The problem with the above script is that it is showing root directory with the full path. How can I just make it show the directories in relation to the one I am working in?

  Read the article

• How to make numbered chapter titles and paragraph headers in iWork Pages 09?

  - by dyve

  For most of my document writing I use iWork Pages (from iWork '09), and it's usually fine for me. I don't miss Microsoft Word, except for one simple feature: the ability to number chapter titles and paragraph headers for easy reference in the contents of the document and for cross references. Somehow, I cannot find this feature in Pages '09. It is possible to number headers by setting the style to numbered, but it doesn't mitigate well into the generated dynamic contents, and paragraphs don't follow the numbering of higher level elements it seems. Does anyone know how to make this work?

  Read the article

• How to make Google Chrome honor my Windows dpi setting?

  - by Ian Boyd

  Google Chrome doesn't seem to respect my dpi-setting in Windows. i run at 150 dpi, but Chrome ignores that; meaning that images and text are teeeeeeny tiny. i hit Ctrl + + Ctrl + + to zoom in. Unfortunatly every new tab, or new window, defaults to the 100% teeny tiny zoom level. Is it possible for either: Chrome to respect my Windows dpi setting? Chrome to remember my zoom preference? Keywords: chrome, high dpi, accessibility Checked version: 4.0.249.78

  Read the article

• Mac ASL: Unable to see my application's log messages

  - by trojanfoe

  I have just added ASL logging support to my application but I cannot see any log entries using Console.app. I am logging with facility 'com.mydomain.myapp' (that's not the actual value) and have even added an entry to /private/etc/asl.conf to tell syslogd to 'store' entries at this Facility (with any Level): ? [= Facility com.mydomain.myapp] store I HUP'd syslogd with no success so I restarted my MacBook Pro, which also made no difference. I know my application is logging OK as I have added the option ASL_OPT_STDERR when calling asl_open() and can see the entries on stderr. Any help would be must appreciated!

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• Accessing multiple local HD's or RAID with ESXi 4.0

  - by Shawn Anderson

  How to I get additional HD's to be recognized and used by ESXi 4.0. When I purchased my system I had two 2TB HD's, but when I installed ESXi it only recognized one of them. I'm happy to get whatever number of drives that I need (I have a four bay SATA in my Dell T310). What are some options? RAID? If so, is it supported. I guess I would need hardware instead of software since ESXi is so small. The VMWare forums (where I've lived for the last two days) are a charlie foxtrot of outdated and conflicting info. I want to utilize my T310, with 32 GB RAM, 2.8GHz quad core to run many lab Windows VM's. I don't need production level availability but I do want decent performance, even though it's in a lab environment. A huge thanks to Jim B., Zypher, Helvick, and Jeff Hengesbach who posted answers to my earlier predecessor question on why ESXi was so sluggish.

  Read the article

• Log "date -s" command

  - by LinuxPenseur

  Hi, I know that the date -s <STRING> command sets the time described by the string STRING. What i want is to log the above command whenever it is used to set the time into the file /tmp/log/user.log. In my Linux distribution the logging is done by syslog-ng. I already have some logs going into /tmp/log/user.log. This is the content of /etc/syslog-ng/syslog-ng.conf in my system for logging into /tmp/log/user.log destination d_notice { file("/tmp/log/user.log");}; filter f_filter10 { level(notice) and not facility(mail,authpriv,cron); }; log { source(s_sys); filter(f_filter10); destination(d_notice); }; What should i do so that date -s command is also logged into /tmp/log/user.log

  Read the article

• AMD FX 8350 potentially overheating

  - by rhughes

  I am worried that my CPU is overheating when running at maximum capacity. I have not overclocked the machine. The machine often powers down after a couple of minutes of max CPU usage. I get the following events in the Event Log after the crash: Log Name: System Source: Microsoft-Windows-Kernel-Power Date: 11/10/2013 12:05:40 Event ID: 41 Task Category: (63) Level: Critical Keywords: (2) User: SYSTEM Computer: home-pc Description: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. What can I do to confirm this or further narrow down this issue? Due to the sudden nature of the crash, no MEMORY.DMP is created I believe. I am happy to post any extra information that is needed.

  Read the article

• Remove server from loadbalancer [on hold]

  - by Cris

  Our datacenter is load balancing the traffic to our weblogic servers based on an application deployed on each server called probe.ear It is a simple java app which is accessed by the loadbalancer and if it accessible it will redirect traffic to this server as well. When we want to remove one node from the loadbalancer we just stop the probe app and new traffic is not redirected to it BUT I am asking myself what about the current requests? The responses for the current requests are executed (completed). I did not had time to test (will do that first thing when go back to work) but on theoretical level for me it make sense to do so unless the loadbalancer has some special settings. Does my reasoning make sense to you? Just to make it clear since it was reported the question is not clear. Is there a way to configure a load balancer in a way that from a specific moment will not redirect traffic to a certain server without reseting the current requests ?

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• How can Firefox masquerade as Chrome?

  - by Christos Jonathan Hayward

  I have access to Firefox but not Chrome under XP. I would like extensions to make it more Chrome-like: in particular, 1: A tabbed theme that works like Chrome. 2: One address/search bar that will go to URLs and submit search queries appropriately. (I have already installed "Download Statusbar.") I am looking on a relatively superficial level; I'm not hoping to simulate V8 or Chrome's screaming render times. But I would like a setup that minimally breaks the illusion for someone accustomed to Chrome.

  Read the article

• Will Software RAID And iSCSI Work For A SAN

  - by Justin

  I am looking for a SAN solution, but can't afford even entry level solutions. Basically, the SAN is for development and a proof of concept product. The performance doesn't have to be amazing, but needs to be functional. My buddy says we should just setup sotware RAID and software iSCSI in Linux. Essentially I have a spare server with dual Xeon processors, 4GB of memory, and (2) 500GB 7200RPM drives. It's a bit old but working. I am sure there is reason people don't do software RAID and iSCSI, but will performance be usable? Thinking of configuring the drives in RAID 0 (for performance).

  Read the article

• Startup script on Ubuntu 12.04 not getting executed. Dependencies / load order.

  - by user861181

  I want to create a simple startup script on Ubuntu 12.04: myscript.sh #!/bin/sh sudo /etc/init.d/nginx start cd ~/app/current god -c config/resque.god sudo /etc/init.d/redis-server start echo "SCRIPT RUN" I have it at /etc/init.d/myscript.sh When I do sudo chkconfig --level 2345 myscript.sh I get myscript.sh 2345 When I do sudo chkconfig --add myscript.sh I get insserv: warning: script 'K01myscript.sh' missing LSB tags and overrides insserv: warning: script 'myscript.sh' missing LSB tags and overrides The script you are attempting to invoke has been converted to an Upstart job, but lsb-header is not supported for Upstart jobs. insserv: warning: script 'dbus' missing LSB tags and overrides .... myscript.sh 0:off 1:off 2:on 3:on 4:on 5:on 6:off ** EDIT:: I checked the boot.log and it turns out that the script is run, but the problem is that god is not loaded yet when the script is executed. Apparently I want to load this script as the very last thing at startup (or somehow check if god is loaded and then start the script).

  Read the article

• DNS protocol message example

  - by virtual-lab

  hello there, I am trying to figure out how to send out DNS messages from an application socket adapter to a DNSBL. I spent the last two days understanding the basics, including experimenting with WireShark to catch an example of message exchanged. Now I would like to query the DNS without using dig or host command (I'm using Ubuntu); how can I perform this action at low level, without the help of these tools in wrapping the request in a proper DNS message format? How the message should be post it? Hex or String? Thanks in advance for any help. Regards Alessandro Ilardo

  Read the article

• Best way to script checking whether a machine is on the corporate network

  - by Ben

  I am writing a Powershell script to determine if a machine is on the corporate network. The machine may or may not be on the domain, so I want to check at "IP" level. Have written something to check by pinging a couple of servers on a couple of different subnets (to get around the risk of someone being on another (external) subnet with a host on the same IP.) Works, but it's a bit slow, and not especially "future-proof" - e.g. in 2 years time when I decomission the server it'll break. Is there a way I can use the dns suffix being given by the local dhcp server? Just direct me what I need to check - I can figure out the script. Ta, Ben

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

• How to disable internet access at night on the router?

  - by izb

  I have an internet connection that I'd like to be enabled only during the day. With multiple household internet devices, this would need to be something disabled at the level of the router. I don't believe the router offers this sort of functionality, but I'm reasonably familiar with setting up web servers and the like, and I'm wondering if I can set up some sort of proxy server on the internet that the router must go through and have that proxy only active at certain times of day. It's a bit vague I know, but is something like this even possible? If not, are there other solutions to the problem?

  Read the article

• Using local proxy to specify used NIC on Windows 7?

  - by Nico

  I'm running Windows 7 and have 2 NIC installed, both are connected to the Internet (nic#1 LTE, nic#2 DSL). Windows 7 will only allow me to specify a binding order and a metric on which interface to chose but i can't specify this on an application level. My Idea was to use a local proxy server and use the proxy server whenever i want to use nic#2. I tried wingate and free proxy, both applications will let me chose the interface i want to use but this setting seems to have no effect? This is how i configured the applications: http://imageshack.us/photo/my-images/69/freeproxysettings.jpg/ http://imageshack.us/photo/my-images/811/wingateproxysettings.jpg/ Is what i'm trying to do in anyway possible?

  Read the article

• converting node inheritance to hiera

  - by quickshiftin

  I'm working on moving over a node inheritance tree to hiera. Presently working on the hierarchy. Prior to hiera, my nodes had a hierarchy as such base pre-prod qa nodes staging nodes development nodes prod nodes Now I'm trying to get the same tier with hiera. Starting out I have this :hierarchy: - base - "%{environment}" - "%{clientcert}" but I need another level to capture pre-prod and prod. My thought would be to add an entry to puppet.conf, something like [agent] realm = pre-prod then :hierarchy: - base - "%{realm}" - "%{environment}" - "%{clientcert}" A couple of questions Are you allowed to place arbitrary properties into puppet.conf? Will hiera see the realm property?

  Read the article

• Windows 7 cannot join samba domain

  - by Antonis Christofides

  I have a 3.5.6 samba server with a LDAP backend (both on Debian 6.0). I've been successfully adding Windows XP machines to the domain for years. I now try to add Windows 7. I have made the recommended registry changes, but I don't have any success so far. Here is what happens: 1. I go to computer name, select "Domain" instead of "Workgroup", type in the domain name, click OK. It asks me for the username and password of an account that can add computers to the domain; I enter them. After about 40 seconds, I get the following message: The following error occurred attempting to join the domain "ITIA": The specified computer account could not be found. Contact an administrator to verify the account is in the domain. If the account has been deleted unjoin, reboot, and rejoin the domain. Despite this, the samba server successfully creates the computer account. 2. Therefore, if I try again a second time, without deleting the already created computer account, I get a different error: The following error occurred attempting to join the domain "ITIA": The specified account already exists. (Note that until a while ago samba wasn't configured to automatically create computer accounts. What I did whenever I wanted an XP to join was to manually create it. When I first attempted to solve the Windows 7 join problem, I setup samba to do this automatically, as this is what most people do, as I understand, and I thought that it might be related. I haven't attempted to add an XP since I made this change, so I don't know if it works, but whether it works or not, the problem remains.) Update 1: Here are the relevant parts of smb.conf: [global] panic action = /usr/share/samba/panic-action %d workgroup = ITIA server string = Itia file server announce as = NT interfaces = 147.102.160.1 volume = %h passdb backend = ldapsam:ldap://ldap.itia.ntua.gr:389 ldap admin dn = uid=samba,ou=daemons,dc=itia,dc=ntua,dc=gr ldap ssl = off ldap suffix = dc=itia,dc=ntua,dc=gr ldap user suffix = ou=people ldap group suffix = ou=groups ldap machine suffix = ou=computers unix password sync = no add machine script = smbldap-useradd -w -i %u log file = /var/log/samba/samba-log.all log level = 3 max log size = 5000 syslog = 2 socket options = SO_KEEPALIVE TCP_NODELAY encrypt passwords = true password level = 1 security = user domain master = yes local master = no wins support = yes domain logons = yes idmap gid = 1000-2000 Update 2: The server has a single network interface eth1 (also an unused eth0 that shows up only in the kernel boot messages) and two ip addresses; the main, 147.102.160.1, and an additional one, 147.102.160.37, that comes up with "ip addr add 147.102.160.37/32 dev eth1" (used only for a web site that has a different certificate than other web sites served from the same machine). One of the problems I recently faced was that samba was using the latter IP address. I fixed that by adding the "interfaces = 147.102.160.1" statement in smb.conf. Now: acheloos:/etc/apache2# tcpdump host 147.102.160.40 and not port 5900 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 13:13:56.549048 IP lithaios.itia.civil.ntua.gr.netbios-dgm > 147.102.160.255.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549056 ARP, Request who-has acheloos2.itia.civil.ntua.gr tell lithaios.itia.civil.ntua.gr, length 46 13:13:56.549091 ARP, Reply acheloos2.itia.civil.ntua.gr is-at 00:10:4b:b4:9e:59 (oui Unknown), length 28 13:13:56.549324 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549608 IP lithaios.itia.civil.ntua.gr.netbios-dgm > acheloos2.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.549741 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.550364 IP lithaios.itia.civil.ntua.gr.netbios-dgm > acheloos.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) 13:13:56.550468 IP acheloos.itia.civil.ntua.gr.netbios-dgm > lithaios.itia.civil.ntua.gr.netbios-dgm: NBT UDP PACKET(138) (acheloos2 is the second IP address, 147.102.160.37). The above dump occurs when I click "OK" (to join the domain), until it asks me for the username and password of a user that can join the domain. I don't know why the client is contacting the second IP address. I tried temporarily deactivating it, but I still had some related ARP traffic (though I think not IP traffic).

  Read the article

• Solaris 10 opencsw git package issue with bitbucket git hosting

  - by zephyrus00jp

  Has anyone tried using `git' from opencsw package in order to work with bitbucket source hosting service (under solaris10)? I tried to use git as the bitbucket documentation explains, and - under Debian GNU/Linux, it worked flawlessly as described, but - under Solaris 10, I got Authentication Failed message. I even tried to run truss to see anything is suspicious but could not find any smoking gun under solaris why it failed. ldd git-binary didnd't show anything suspicious either (except for the libcrypt library which could be a suspicious to think about export restrictions. Have they shipped incompatible version? BUT since the password is typed into https: connection, I suspect it is only a matter of web-level cryptography and should be universal these days.) I am now tempted to compile git suite under solaris 10, but I did find people who seem to be using git with bitbucket under solaris 10 and am wondering what could be wrong.

  Read the article

• How to add timestamp to the logfilename with the apache log4j

  - by swati

  I am new to using apache logger . I have downloaded the log4j-xx and i have the following text configuration file # Set root logger level to DEBUG and its only appender to mainFormat. log4j.rootLogger = TRACE, mainFormat, FILE # mainFormat is set to be a ConsoleAppender. log4j.appender.mainFormat=org.apache.log4j.ConsoleAppender # mainFormat uses PatternLayout. log4j.appender.mainFormat.layout=org.apache.log4j.PatternLayout log4j.appender.mainFormat.layout.ConversionPattern=%d [%t] %-5p %c - %m%n #File makes a file of the output. log4j.appender.FILE=org.apache.log4j.FileAppender log4j.appender.FILE.File=log4j_HAPR001_OutputFile.log log4j.appender.FILE.layout=org.apache.log4j.PatternLayout log4j.appender.FILE.layout.ConversionPattern=%d [%t] %-5p %c - %m%n i use the above config file to create the log file. Now i wanted to add the current time stamp to the log file. Is there any way to do this. If yes can some one please give me the instructions how to do. Thanks in advance. Regards, Swati

  Read the article

< Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >