Search Results

Search found 20114 results on 805 pages for 'network adapter'.

Page 353/805 | < Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >

• static routes, cisco ASA, remote locations

  - by Jeff

  192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

  Read the article

• dhcpd won't let go of old leases

  - by Jakobud

  We have DHCP setup to hand out leases in the following range: 192.168.10.190 - 192.168.10.254 (roughly 65 leases) Our small business network only has about 30 computers that use DHCP. We noticed that dhcpd stopped handing out new dynamic leases to the computers, even though there are definitely not 65 computers on the network. Why has it stopped handing out leases? Is it not releasing old un-used leases? How do we tell dhcpd to let go of old leases and start handing out fresh ones again?

  Read the article

• Cannot control the fan on a Sony Vaio laptop

  - by Xobb

  I've got Sony Vaio laptop and my fan is on all the time, though the temperature on the video-adapter is always over 60°?. As I've googled, vaiofand does not support VPC-EA series. Is there anything I can do with that or I need another laptop? I'm using the following graphics card: 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] though the problem is not with the graphics card. I've mentioned its temperature as the highest (64°C now btw). Seems like the notebook is always overheated and I cannot control the fan speed to make it cooler. And yes, I'm using the proprietary driver ATI/AMD FGLRX graphics driver. I'm using Kubuntu 11.04.

  Read the article

• MIDI Over Networking on OSX: Lots of beachballing

  - by Yar

  I have 4 computers connected to a Wifi router (with no Internet uplink). Whenever we enter the Network interface for Audio/Midi preferences in ANY of the computers, the Mac beachballs and then finally finds its way. Occasionally, however, one of the computers fails to receive the MIDI information that was destined for it via the Network MIDI interface. Changing to all wired connections does NOT help. Adding Internet uplink DOES help and the problem is resolved. This makes no sense to me as the computers can access each other just fine with or without the Internet uplink. Any ideas? [NOTE: I'll update the question if people correct my terminology, or feel free to do that if you have the rights].

  Read the article

• default gateway of a host

  - by varun

  if my understanding is correct, the following is what happens when a host A wants to communicate with a machine X outside its network. 1) The host ,checks it routing table to find out if there is any direct routes to the machine. 2) It finds out that the machine is outside its network and has to sent the packets to the default gateway(router) R. 3) The host sents an ARP broadcast to get the mac of the router R. 4) After getting the MAC, the host creates a packet with src IP and MAC as that of the host A, dest IP of the remote machine X and dest MAC of the router R. 5)The router R receives the packet, either drops its or sents its to its next hope, which can be another router or the remote machine X itself. Can anyone explain, how the steps would be, if i set the default gateway of the host A as host A itself...?

  Read the article

• What the hell was THAT?!?

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• smartctl not returning on HBA that's secure-erasing a different drive

  - by Stu2000

  Whenever I run smartctl -i /dev/sd* where * is a drive that is plugged into the same host bus adapter as another drive that is currently being erased with an hdparm secure erase command, the smart command will just 'hang' and not return (blocked) until the erasure of the other drive is finished. To make matters worse you can't cntrl-c out of it. Has anyone else had this issue? Is there another way to retrieve smart data from a drive, which doesn't block? I noticed that I can still use the udevadm command to retrieve the serial and model of the drive which is useful but doesn't appear to have any smart data. Any information relating to this matter is appreciated, especially if you can tell me another way to retrieve the S.M.A.R.T data that might work. Regards, Stuart

  Read the article

• WEP authentication suddenly failing in Ubuntu

  - by kellishaver

  I'm running Ubuntu 9.10 and after a recent reboot, I'm now unable to authenticate to wireless networks using WEP encryption. I can connect fine to open networks (no idea about WPA). When trying to connect via WEP, I'm continually prompted for the network key, which I know I have entered correctly (and should have been/is saved in my keyring anyway). Everything had been working fine until the reboot. No updates had been installed or configuration changes made. Hardware-wise, everything looks fine (http://pastebin.org/113777), and the fact that connecting to an open network works just fine leads me to think this is a software issue. I just don't know where to begin fixing it. Any insights would be greatly appreciated.

  Read the article

• Useless Plesk Error?

  - by Josh Pennington

  I am trying to determine why Plesk on my server won't start and I have no idea where to even start (since my hosting company appears to not want to help me out). Anyways, the error in my Plesk error_log is as follows: 2010-12-25 21:30:28: (log.c.75) server started 2010-12-25 21:30:28: (network.c.336) SSL: error:00000000:lib(0):func(0):reason(0) 2010-12-25 21:30:28: (log.c.75) server started 2010-12-25 21:30:28: (network.c.336) SSL: error:00000000:lib(0):func(0):reason(0) It leads me to believe its a problem with the SSL on the server but I am not sure what to make of the error. Can someone lead me in the right direction? Thanks Josh Pennington

  Read the article

• "Account locked out" security event at midnight

  - by Kev

  The last three midnights I've gotten an Event ID 539 in the log...about my own account: Event Type: Failure Audit Event Source: Security Event Category: Logon/Logoff Event ID: 539 Date: 2010-04-26 Time: 12:00:20 AM User: NT AUTHORITY\SYSTEM Computer: SERVERNAME Description: Logon Failure: Reason: Account locked out User Name: MyUser Domain: MYDOMAIN Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: SERVERNAME Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: - Source Port: - It's always within a half minute of midnight. There are no login attempts before it. Right after it (in the same second) there's a success audit entry: Logon attempt using explicit credentials: Logged on user: User Name: SERVERNAME$ Domain: MYDOMAIN Logon ID: (0x0,0x3E7) Logon GUID: - User whose credentials were used: Target User Name: MyUser Target Domain: MYDOMAIN Target Logon GUID: - Target Server Name: servername.mydomain.lan Target Server Info: servername.mydomain.lan Caller Process ID: 2724 Source Network Address: - Source Port: - The process ID was the same on all three of them, so I looked it up, and right now at least it maps to TCP/IP Services (Microsoft). I don't believe I changed any policies or anything on Friday. How should I interpret this?

  Read the article

• Show Notes: Getting Past the Cloud Hype

  - by Bob Rhubart

  This week’s ArchBeat podcast features an unvarnished bit of conversation culled from a recent virtual meet-up. These meet-ups are informal conversations among architects, many of who have participated in previous ArchBeat programs. There’s no prearranged topic, so the participants talk about whatever is on their minds. The most recent meet-up included Oracle ACE Director Ran Batra, director of cloud computing product development with AT&T, and Daniel Templeton, principal product manager for Oracle Grid Engine, and the man behind Dan T’s GridBlog. The conversation took place at the end of the year – and the end of the decade – a time when most tech publications feature their predictions for the coming year.  I wanted a different spin on that theme, so I asked Ron and Dan to talk about the technologies about which they weren’t all that optimistic.   I found that ten-minute chunk of conversation particularly interesting, so that’s what you’re going to hear this week. Listen Get Social If you have questions or comment for Ron and/or Daniel you can connect via the following: Ron Batra Blog | Twitter | LinkedIn | Oracle Mix | Oracle ACE Profile Daniel Templeton Blog | Twitter | LinkedIn Coming Up Oracle ACE Director Debra Lilley talks about her role in the UKOUG’s development group and that group’s collaboration with Oracle on Oracle Fusion Applications. Dr Frank Munz, author of Middleware and Cloud Computing: Oracle Fusion Middleware on Amazon Web Services and Rackspace Cloud. Stay tuned: http://feeds2.feedburner.com/OtnArch2ArchRSS   del.icio.us Tags: oracle,oracle technology network,archbeat,cloud computing,software architect,podcast Technorati Tags: oracle,oracle technology network,archbeat,cloud computing,software architect,podcast

  Read the article

• Wireless not detected on an hp Pavilion g6 - RT5390PCIe

  - by Earl Larson

  I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

  Read the article

• VMXNET3 nic loses the ability to update ARP table after N hours

  - by Peter

  I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without issue. A tcpdump of the offending NIC shows only ARP broadcasts but no responses. None of the other VMs on the vDS see the ARP broadcasts from the offending NIC. The only way I can currently solve the problem is to reboot the VM and then everything works for a while. I've tried changing the port on the vDS and even flipping the network configurations after I lose eth1's ARP table, but the ARP problem follows eth1 but I can access the machines that were originally on eth1. If I statically add the arp entries for machines on the same subnet I have no problems with connectivity. The Hypervisor is an HP BL49X series with flex-10 network modules. Has anyone seen anything like this before?

  Read the article

• Ethernet card not detected on Ubuntu Server 12.04

  - by Dana

  My onboard ethernet isn't detected after a re-install of Server 12.04. For reasons I won't get into here, I had to put the server's drive into another machine to install Ubuntu, then swap back into the server. So the server starts up fine, except for the "Waiting for network configuration". I read in another article that Server, by default, doesn't handle new mac addresses for hardware changes dynamically, unlike Ubuntu Desktop, but a look at /etc/udev/rules.d/70-persistent-net.rules shows only one ethernet interface. Shouldn't it show both the old, and the new? lspci -vv shows an ethernet interface, so what the heck is going on? I should mention that the onboard LAN is enabled in the BIOS. And I know this isn't important, but all this started when I changed some network configuration settings in webmin before the re-install. It couldn't download any updates, so I tinkered a little. Broke, it, installed FreeNAS, which worked, but I didn't like it, then went back to Ubuntu Server, and now I'm in this pickle. Thanks for any advice!

  Read the article

• Running 12.04 as a gateway - resolvconf, dhclient and dnsmasq integration

  - by Adam

  I have a gateway server which is set up originally with Ubuntu desktop 12.04 - perhaps a mistake, I don't know, something to bear in mind. I ripped out network-manager and now want to get resolvconf, dhclient and dnsmasq to play well together. dhclient gets the gateway's eth0 WAN ip address and the ISP DNS name server from the modem. dnsmasq needs to serve dhcp to the rest of the lan on eth1 and acts as a DNS cache both for the lan and for the gateway machine. I also set up iptables as a firewall. Right now, the gateway's /etc/resolv.conf shows only name server = 127.0.0.1 which is correct AFAIK. However I don't think that dhclient is giving dnsmasq the ISP DNS name server nor is dnsmasq picking up the OpenDNS and Google name servers I specified in /etc/network/interfaces - at the moment look-ups, i.e. ping or surfing, don't work unless I manually edit /etc/resolv.conf to put in an upstream name server like 8.8.8.8 So I removed the resolvconf package. Now I'm not getting dhcp on my lan and I'm not able to do DNS look-ups on the host itself - I can surf and ping on the net, but not 127.0.0.1. Where do I go from here? This setup with the config for dhclient and dnsmasq, and the same resolv.conf and hosts files worked on my old debian box.

  Read the article

• autofs mac os x afp not loading as correct user?

  - by Stephen Furlani

  Hello, I am way out of my depth, and I am trying to get all of my nodes on a cluster to mount a drive on my head node. I've got /etc/auto_master and /etc/auto_afp configured according to Apple's "Autofs: Automatically Mounting Network File Shares in Mac OS X" White Paper: /etc/auto_master +auto_master # Use directory service /net -hosts -nobrowse,hidefromfinder,nosuid /home auto_home -nobrowse,hidefromfinder /Network/Servers -fstab /- -static /- auto_afp /etc/auto_afp /Volumes/userA -fstype=afp afp://userA:[email protected]:/ /Volumes/userB -fstype=afp afp://userB:[email protected]:/ I am logged into a compute-node as userA. automount appears to mount both /Volumes/userA and /Volumes/userB to head-node.local:/Users/userA/Documents/ even though I have usernames, passwords, and user-directory specified in the afp url. If I go and login with Finder - it mounts userB appropriately. File sharing and cd/dvd sharing is enabled on all computers involved. Am I doing the right thing, and if so, what did I do wrong? -Stephen

  Read the article

• Can't connect to sql server 2008 named instance

  - by hcsrpm

  I have sql server 2005 and 2008 running on a server on my local (and very straightforward) network. Using sql management studio 2008 and visual studio 2008, I can connect over the network to the 2005 instance which is the default instance. I can't connect to the 08 instance (named MC08). I can connect to both when logged in to the server. Remote connections have been enabled for MC08 and dynamic ports is turned off (assigned to port 1045). The sql browser service is running as well. This used to work so I'm not sure what has changed. I can't connect using the IP address either. Nothing unusual in the event log either. Any ideas?

  Read the article

• Sonicwall settings for Polycom TFTP

  - by Michael Glenn

  I'm switching our VoIP phones (Polycom 301s and 501s) to our data network. They were previously segmented to their own network. This means disabling the DHCP on the Trixbox (Asterisk) server and configuring the Sonicwall TZ 210 DHCP to indicate that Trixbox is the TFTP server. The Polycom phones are stating "could not contact boot server". All phones are configured to TFTP and were confirmed working when previously using the Trixbox server for DHCP. Trixbox DHCP is now turned off. I've configured options 66(as String), 128(as IP) and 150(as IP) in DHCP and added them to a TFTP Option Group. I've enabled "Allow BOOTP Clients to use Range" for the Dynamic IP range and assigned the Option Group TFTP as the DHCP Generic Option Group. Any idea what I'm missing? Is there a separate tool to inspect the DHCP response to compare Trixbox to the Sonicwall?

  Read the article

• Oracle OpenWorld São Paulo Is Back!

  - by Kristin Rose

  Guess what’s back and bigger than ever! Oracle OpenWorld São Paulo, and we can’t wait to see YOU there! Be part of the first ever Oracle PartnerNetwork Exchange Latin America, a program that incorporates special activities specifically tailored to you, our partners. OracleOpenWorld Latin America is taking place from December 4th – 6th at the Transamerica Expo Center, so if you haven’t already registered, hurry and do so to take advantage of our Early Bird pricing here! This year’s jam-packed agenda includes keynotes from Hugo Freytes, SVP of Latin America Alliances and Channels, Judson Althoff, SVP of Worldwide Alliances and Channels and many more! The OPN Keynote session will take place on December 5th from 10:00am to 12:00am, and the program will feature four tracks including Applications, Cloud, Engineered Systems and Technology for partners, complete with endless content! Click here to view the Oracle OpenWorld Latin America Oracle PartnerNetwork Agenda. Also, we wanted to offer a huge THANK YOU to our 2012 Oracle PartnerNetwork Exchange Latin America and Lounge sponsors: Avnet and Preteco! Be sure to stop by our Oracle PartnerNetwork Lounge to hold meetings, network with your peers, and engage in relevant conversations with your partners, customers and other industry professionals. Finally, don’t wait to register! Early Bird Pricing for OPN Exchange @ OpenWorld has ends November, 23. You really don't want to miss this great opportunity to learn, network, and be a part of the experience. Register here! Welcome to the new Oracle PartnerNetwork Exchange @ OpenWorld Latin America 2012! The OPN Communications Team

  Read the article

• SQL Azure Security: DoS

  - by Herve Roggero

  Since I decided to understand in more depth how SQL Azure works I started to dig into its performance characteristics. So I decided to write an application that allows me to put SQL Azure to the test and compare results with a local SQL Server database. One of the options I added is the ability to issue the same command on multiple threads to get certain performance metrics. That's when I stumbled on an interesting security feature of SQL Azure: its Denial of Service (DoS) detection engine. What this security feature does is that it performs a check on the number of connections being established, and if the rate of connection is too high, SQL Azure blocks all communication from that machine. I am still trying to learn more about this specific feature, but it appears that going to the SQL Azure portal and testing the connection from the portal "resets" the feature and you are allowed to connect again... until you reach the login threashold. In the specific test I was performing, all the logins were successful. I haven't tried to login with an invalid account or password... that will be for next time. On my Linked In group (SQL Server and SQL Azure Security: http://www.linkedin.com/groups?gid=2569994&trk=hb_side_g) Chip Andrews (www.sqlsecurity.com) pointed out that this feature in itself could present an internal threat. In theory, a rogue application could be issuing many login requests from a NATed network, which could potentially prevent any production system from connecting to SQL Azure within the same network. My initial response was that this could indeed be the case. However, while the TCP protocol contains the latest NATed IP address of a machine (which masks the origin of the machine making the SQL request), the TDS protocol itself contains the IP Address of the machine making the initial request; so technically there would be a way for SQL Azure to block only the internal IP address making the rogue requests.  So this warrants further investigation... stay tuned...

  Read the article

• Virtualbox PXE Boot Failing with a Windows Server 2008 R2 Server

  - by Vbitz

  Some fast help on this would be good, I have been on this problem for 14 hours. In a Virtualbox test environment I have 2 virtual machines networked together using a internal network (no traffic runs though the host, it is all at a software level). One is a fresh client with 512mb of ram and a dual core set-up, the other is the server with 1.5GB of ram and running server 2008 r2. The server is configured as a dns server, dchp server, domain controller and also serves PXE booting though WDS (Windows Deployment Services). Both machines can see each other and I am able to start a network boot. The issue comes at the second to last stage of the pre windows PE install. On TFTP download of boot.sdi it starts it but stops during the boot process.

  Read the article

• Resealing windows XP stops PXE working

  - by zeocrash

  I'm trying to capture a drive image of a windows xp pro machine. I've gone through the steps and resealed the machine. When i try and network boot the PXE instantly gives the message "PXE-MOF" and ends. I have managed to get network boot to work on this machine whenever XP is not resealed. I have tried Multiple times to get PXE to work after resealing windows, but with no luck. As soon as i unseal it, PXE works every time. I know PXE is supposed to work independent of what's on the hard drive. Is there any way that resealing windows could cause PXE to stop working.

  Read the article

• Hyper-V Cluster with failover - NETWORKING

  - by Adam

  Hi We are looking to setup a 3 node Hyper-V cluster with live migration and failover using: 3 x Dell R710's with dual quad core Xeon & 128 GB RAM & 6 NICs in each 1 x Dell MD 3220i SAN We will be running this setup from a data center and so co-locating our kit. Can anybody explain how we should setup the network connections to make the system redundant? We have looked into this great article but are not sure how to get a 3 server setup correctly and reliably: http://faultbucket.ca/2011/01/hyper-v-failover-cluster-setup/. I believe we need network connections for: live migration, heartbeat, management, hyper-v etc. I assume as we are running it from a DC all IPs will have to be public IPs? Are AD servers will be VMs. One on each Hyper-V server and setup not to be HA.

  Read the article

• Can't complete dropbox installation from behind proxy

  - by Mark Jones

  Problem: My PC on campus sits behind a proxy (requiring authentication) and I can't setup Dropbox. I am convinced that this is a proxy issue as I can't setup Ubuntu one either (but I don't use Ubuntu One so that is not a problem). I have looked at the Ubuntu One fix but it seems to be to modify settings explicitly related to Ubuntu One. I can install the nautilus-dropbox package (compiled from source and from .deb package from website and from software centre) but once I click OK from the "Dropbox Installation" dialog box (prompting me to download the proprietary daemon) the installation just freezes with the OK button pressed. When I look at its process in System Monitor its waiting channel is inet_wait_for_connect. I have set the following proxy directives thus far: Added mj22:**@proxy.waikato.ac.nz:80 information to network proxy settings under network in settings. Added http_host and http_port variables under gconf-editor-system-proxy Added 'host', 'authentication_password' 'authentication_user' and ticked 'user authentication' and 'use_http_proxy' under gconf-editor-system-http_proxy Added export http_proxy="http://mj22:**@proxy.waikato.ac.nz:80/" to /etc/bash.bashrc Added Acquire::http::proxy "http://mj22:**@proxy.waikato.ac.nz:80/"; to /etc/apt/apt.conf (which is what I imagine is letting Software Center retrieve packages). (where ** is my password) I have also added the equivalent ftp and https lines for the above entries. I get the internet fine and Software Centre can download packages but thats it. Related issues: The software centre can't fetch reviews (but can download packages). When trying to add an online account in Gnome 3 a dialog pop up appears with "Error getting a Request Token: Cannot connect to proxy (proxy.waikato.ac.nz)" Updates: After some time (10mins ish) Dropbox shows an error dialog box that reads: Trouble connecting to Dropbox servers. Maybe your internet connection is down, or you need to set you http_proxy environment variable. Is there a way I can see what environment variables are currently set?

  Read the article

• Get Smarter Just By Listening

  - by mark.wilcox

  Occasionally my friends ask me what do I listen/read to keep informed. So I thought I would like to post an update. First - there is an entirely new network being launched by Jason Calacanis called "ThisWeekIn". They have weekly shows on variety of topics including Startups, Android, Twitter, Cloud Computing, Venture Capital and now the iPad. If you want to keep ahead (and really get motivated) - I totally recommend listening to at least This Week in Startups. I also find Cloud Computing helpful. I also like listening to the Android show so that I can see how it's progressing. Because while I love my iPhone/iPad - it's  important to keep the competition in the game up to improve everything. I'm also not opposed to switching to Android if something becomes as nice experience - but so far - my take on Android devices are  - 10 years ago, I would have jumped all over them because of their hackability. But now, I'm in a phase, where I just want these devices to work and most of my creation is in non-programming areas - I find the i* experience better. Second - In terms of general entertaining tech news - I'm a big fan of This Week in Tech. Finally - For a non-geek but very informative show - The Kevin Pollack Show on ThisWeekIn network gets my highest rating. It's basically two-hours of in-depth interview with a wide variety of well-known comedian and movie stars. -- Posted via email from Virtual Identity Dialogue

  Read the article

< Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >