Search Results

Search found 12820 results on 513 pages for 'little devil'.

Page 354/513 | < Previous Page | 350 351 352 353 354 355 356 357 358 359 360 361  | Next Page >

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

  • Synchronize two directories on linux pc

    - by Gab
    I need a distributed filesystem (or a synchronization tool) that is capable of keeping a directory synchronized across 4 pc. My requirements are: offline access (data must be available offline on each pc) preserve execution rights: some files are marked executable on a linux partition. This flag should be replicated. efficient sync strategy: some of my files are 20GB, they are changed quite often, but in very little parts (Virtualbox images). Delta transmissions are welcome. efficient handling of space: no history for files, files shouldn't be copied to temp directories "just in case you break it". it must propagate deletions of files modification can happen in any of the 4 pcs, they should be propagated when other pc are connected. Other specs of my solution are: Sync is over a lan, the total amount of data to be synced is around 180GB, in some ten thousand files. Changes are small, but can happen in big files. At the moment i'm interested in a linux only solution. conflicts either don't happen or are solved with "last one wins" I haven't found any good solution. I've been trying: unison: it is the only one working at the moment, but during the hashing phase it hangs my pc for some minute, disk light steady on. Sparkleshare doesn't handle large files nicely. It keeps an history of all your changes that grows up indefinitely. They promise it will be fixed in next releases, but at the moment it still doesn't fit my needs. owncloud (keeps history of each file i change) coda ? (help! i couldn't set it up correctly!) git-annex assistant transforms all your files in symlinks and mark the original file as read only ("just in case you make a mistake while you modify it"!). Before you edit a file you have to issue a special command "git-annex unlock", that creates a local copy of the file, and you have to remember to lock it again if you want it synchronized. What to try next?

    Read the article

  • sharepoint crawl not indexing main site

    - by user22215
    Guys I'm having some strange search issues' going on with my main portal application. First off let me give you a little back ground on the problem web app. Our Sharepoint environment was originally set up by a consultant that did not follow best practices. She used one web app to house our companies' intranet site, ssp, and mysites. Since than I have provisioned a new ssp that I have segmented correctly I moved all of our other sites over to the new ssp with out any problems . However, I could not assign the main portal app to the new ssp since the portal app housed the ssp site collection. So I deleted the ssp site collection after that I deleted the ssp and assigned the portal app to my new ssp. Now this is where the problem starts when I attempt to crawl this application the crawl starts than stops 5 seconds later with a status of success also it reports that 1 item was successfully crawled. The funny thing is the main portal app has nearly 30000 items. I have tracked the problem down to the web app if I create a test web app than restore the content I have no problem crawling all 30000 items. Also all of my other web apps that use the same ssp have no problem completing crawls. I don't see anything in the ULS logs or server 2003's event viewer. Also I'm using a separate dedicated index server that's configured to crawl itself via host file configuration. I would like to fix this problem with out having to recreate our main portal site due to the fact that we have several custom code modifications where DLL's were registered to the IIS bin folder also I don't even want to get into the Silverlight mods that were done. Any help with this problem is much appreciated Same problem as minehttp://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Server/MS-SharePoint/Q_23885820.html

    Read the article

  • SQL Server Installation: Is it 32 or 64 bit?

    - by CapBBeard
    Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

    Read the article

  • win 7 something is causing excessive disk usage, maybe chrome?

    - by camcam
    On my Win 7 computer, this happens: I work for several hours without problems, also using Chrome Suddenly, just after refreshing a page in Chrome, disk starts being used excessively (here I can close Chrome or not, no matter, the disk won't stop) Disk diod is on all the time and I hear it running like crazy, all computer is a little slowed down It last 5-10 minutes In the meantime, I go to Windows Task Manager and observe what processes are using disk and turn them off one by one - but no success in stopping the excessive disk usage After approximately 10 minutes everything stops I go to Chrome (or re-open it) and refresh the page with mixed results - sometimes the whole process repeats immediately, sometimes not Basically, it is almost always Chrome refreshing random page that starts the excessive disk usage, but killing Chrome process does not stop the disk. Going to the same page in Firefox is not causing problems. Windows Search is turned off. I would like to know what is really happening. Perhaps there is a utility which would allow me to see which process is really using the disk, so that I can disable the service ? (not chrome, because killing chrome does not change anything) or even better, perhaps there is a way to fix it?

    Read the article

  • Fedora installed in Legacy mode, how to make it work in UEFI?

    - by TryntaLearn
    I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

    Read the article

  • Exchange 2010 OWA- Open Other User Mailbox

    - by Benjamin Jones
    I just started working for this small firm (30 people) a little bit ago, replacing their System Admin. First thing I noticed was Exchange Server 2010 was WAY out of date. Believe it or not they did not have SP1 installed. So after I installed and configured Exchange 2010 SP3 and redirected OWA I noticed something in OWA. I could add ANYONE's User Mailbox WITHOUT giving mailbox premission. I created a couple test users, same thing. I even had another employee provide me access to their OWA and they could open anyone's Inbox without granting permission. I don't want to play the blame game, but I was SHOCKED that this was going on. Luckly being such a small company I'll be able to cover this mistake that I did not create, BUT HOW? My guess is that I need to find out where the past System Admin went wrong in providing Full Access Permission? Or could this be a Auto-Mapping issue? I found this article: http://technet.microsoft.com/en-us/library/hh529943.aspx This might work $FixAutoMapping = Get-MailboxPermission sharedmailbox |where {$_.AccessRights -eq "FullAccess" -and $_.IsInherited -eq $false} $FixAutoMapping | Remove-MailboxPermission $FixAutoMapping | ForEach {Add-MailboxPermission -Identity $_.Identity -User $_.User -AccessRights:FullAccess -AutoMapping $false} However how do I insert the above code into Powershell? Again I was thrown into this mess and I'm just trying to iron out this tangled mess.

    Read the article

  • Liked Arch Linux - but I am still not sure if its the right distro for me...

    - by BlackAndGold
    As the title says... I used Arch Linux for a while and liked it a lot: leightweight, sleek, fast and well documented with a great community. However I had to format my hd and for the sake of being too lazy to reinstall arch, I used windows 7 exclusively for a while. Now I want to get back to linux again (still dual boot), mainly for web development purposes and using handy tools such as rsync ect. Again, I liked Arch, but there is too much tweeking, too much reading up and too much figuring out what to do as well es some bad suprises especially when you need them the least and when just quickly want to get some work done. I kind of would like to have a little more "out of the box" distro that is still fast and somewhat leighweight and of course reliable. I actually considered Ubuntu, which I am not too big of a fan of, but I will still give the minimal install a shot. However other distros seem interesting as well, such as crunchbang and mint debian ecpecially. My question, hoping this isn't too boring for many you, what is the right distro for me?

    Read the article

  • HP/Lenovo alternative to Buffalo iSCSI TerraStation?

    - by Robin Day
    I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/Lenovo? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

    Read the article

  • Hadoop streaming job on EC2 stays in "pending" state

    - by liamf
    Trying to experiment with Hadoop and Streaming using cloudera distribution CDH3 on Ubuntu. Have valid data in hdfs:// ready for processing. Wrote little streaming mapper in python. When I launch a mapper only job using: hadoop jar /usr/lib/hadoop/contrib/streaming/hadoop-streaming*.jar -file /usr/src/mystuff/mapper.py -mapper /usr/src/mystuff/mapper.py -input /incoming/STBFlow/* -output testOP hadoop duly decides it will use 66 mappers on the cluster to process the data. The testOP directory is created on HDFS. A job_conf.xml file is created. But the job tracker UI at port 50030 never shows the job moving out of "pending" state and nothing else happens. CPU usage stays at zero. (the job is created though) If I give it a single file (instead of the entire directory) as input, same result (except Hadoop decides it needs 2 mappers instead of 66). I also tried using the "dumbo" Python utility and launching jobs using that: same result: permanently pending. So I am missing something basic: could someone help me out with what I should look for? The cluster is on Amazon EC2. Firewall issues maybe: ports are enabled explicitly, case by case, in the cluster security group.

    Read the article

  • Multiple Remote Desktop Connection in Windows Server 2003?

    - by Joel Bradley
    My company is transitioning all user PC's to Windows 7 64-Bit in anticipation of the 2014 cutoff for Windows XP support. So far everything has been going great except for one specific piece of software that will not run in Windows 7. The current plan is to give everyone a cheap secondary PC to run this software but I feel that's a little much for software that's not even used all the time, although it is essential. I've suggested we install virtual machines but the company does not want to pay for the XP licences. I have access to a copy of Windows Server 2003 that is no longer being used and I was wondering if it was possible to create a remote desktop server. I know it can be done on a one-to-one basis, but this is a 15 person helpdesk. I'd like to be able to support multiple remote dekstop sessions, each with their own logins and dekstops. Is this possible? Are there any other alternatives to my issue? FYI, I've been told that XP mode is only free for consumers. There are costs when used in a corporate environment.

    Read the article

  • Best grep-like tool

    - by e-satis
    I do in file search a lot, and used to love grep. Then I learn the existence of egrep, so I switched to benefit from the advanced regexp. Then I discovered the Eclipse search tool. Much easier to use that grep. Then I found ack : fast, easy, powerful. And now I use grin, which is smooth for pythonistas. I know there is also a couple of this kind of tools with a GUI. So what tool do you use, and why do you think it's the best. Practical features generally are : fast to fire and use; speedy processing; automatically ignore useless files; colored output; output lines, filename, context; allow complex regexp; allow a custom filtering and ouput; GUI + command line intergation; let you open an editor from the result set. There are some related posts on SO : http://stackoverflow.com/questions/87350/what-are-good-grep-tool-for-windows http://stackoverflow.com/questions/981601/colorized-grep-viewing-the-entire-file-with-highlighting http://stackoverflow.com/questions/1028107/is-there-some-unix-util-that-will-allow-me-to-grep-multiple-files-with-little-type http://stackoverflow.com/questions/1027906/unix-find-grep-syntax-vs-awk

    Read the article

  • IP tables blocking access to most hosts but some accesses being logged

    - by epo
    What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

    Read the article

  • How to setup port forwarding from my Webserver (apache) to my Database server (mysql)

    - by karman888
    Hello again guys, and thank you for your help so far. Here is my problem: I have two remote dedicated servers, one webserver that runs apache, and one db server that runs mysql. The apache server is visible on the internet of course, but the second server is only visible to the apache server because they are connected with LAN. I need to connect to the remote mysql server through internet from my home-pc , but only apache server is visible to my home-pc. How can i setup port-forwarding from my apache server to the mysql server so i will be able to "see" the mysql server from my home-pc? This question is a follow-up from my first question Connect to remote mysql server from my application. Problem is that Mysql server is on LAN in which you answered me and helped me a lot by telling me to do "port-forwarding". I looked over the internet, and i cant find a good how-to to do port-forwarding. I'm an experienced programmer, but have little experience on hardware and networks. I can understand though what must be done, so i just need a litle help to sort things out :) I hope you can help me guys, Thank you in advance p.s. machine that Apache is running is on CentOS, mysql server also CentOS. p.s2 webserver runs WebHostManager i dont know if that makes any difference or it can be made easily through this, i just mention it :)

    Read the article

  • For Windows XP: How to uninstall Broadcom Bluetooth software that won't disappear

    - by T. Webster
    Hello, my situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to install it (so I can install the Toshiba stack for the Cirago adapter). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. I would include pictures here, but I don't have 10 reputation yet, so I'll just use links instead. picasaweb.google.com/lh/photo/2NAos6BP9UigPtJKaYRGyQ?feat=directlink But I do see that the little Bluetooth icon still persists: picasaweb.google.com/lh/photo/kbxgPP8ZLxhjX4ob2YjSew?feat=directlink I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. picasaweb.google.com/lh/photo/hWDo-OzB8ApibzeHA_saxQ?feat=directlink What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

    Read the article

  • Bad performance with Linux software RAID5 and LUKS encryption

    - by Philipp Wendler
    I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

    Read the article

  • Disk usage on IIS, PHP5, performance problems.

    - by Jacob84
    Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

    Read the article

  • SamFS performance problem on file creation

    - by Gregor Longariva
    I have two samfs filesystems (samfs1 and samfs2), both on the same 6130, both with the same config/watermarks/timeouts etc. creating a file on samfs2 works as it should, on samfs1 not. A little simple script shows up, that every while and then the file creation needs between 11 and 28 seconds: stan 12:32 [scratch]# while ( 1 ) while? echo - while? time echo test file while? time mv file file2 while? echo + while? sleep 1 while? end 0.00u 0.00s 0:00.01 0.0% 0.00u 0.00s 0:00.00 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.03 0.0% + 0.00u 0.00s 0:23.71 0.0% 0.00u 0.00s 0:00.14 0.0% + 0.00u 0.00s 0:00.18 0.0% 0.00u 0.00s 0:00.13 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.06 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.04 0.0% + 0.00u 0.00s 0:00.04 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.01 0.0% + 0.00u 0.00s 0:26.05 0.0% 0.00u 0.00s 0:00.50 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.06 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.12 0.0% + Any idea where the problem could be?

    Read the article

  • Things to check for an internet-facing email server.

    - by Shtééf
    I'm faced with the task of setting up a public-internet-facing email server, that will be relaying mail for all of our other servers in the network. While the software in itself is set up in few keystrokes, what little experience I have with managing an email server has thought me that there are tons of awkward filtering techniques employed by other email systems. Systems that my own server will inevitably interact with a some point. Hence, my questions: What things should be kept in mind and double checked when setting up an email server? What resources are available for checking if my email server is set-up correctly? I'm specifically NOT looking for instructions for any given mail server, such as Exchange or Postfix. But it's okay to say: “you should have X and Y in your set-up, because when talking to server software Z, it typically tries to weed out open relays by checking for these.” Some things I've discovered myself: Make sure forward and reverse DNS are set up. Mail servers tend to do a reverse lookup for the peer IP-address when receiving. Matching a reverse look up with a follow-up forward lookup is probably employed to weed out open relays run through malware on home networks. Make sure the user in the From-address exists. The From-address is easily spoofed. A receiving mail server may try to contact the mail server in the From-domain, and see if the From-user actually exists.

    Read the article

  • Removing extended partition without deleting logical in it

    - by HisDudeness
    I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

    Read the article

  • Retrieve a user's Exchange database in powershell

    - by Paul
    Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

    Read the article

  • Please help to find a solution for two way, real-time synchronization on Centos 5.5 64Bit

    - by Vipul Limbachiya
    I am in need of a real time, two way synchronization software for Centos 5.5 / 64Bit. Here's little explanation: It needs to be able to perform: Two way synchronization. It must be realtime. By realtime means it can be almost realtime, i.e. a delay of 1 second for example is fine. And the folders are on the same server. I am currently using GlusterFS across two webservers. However, it has extremely poor small file read performance and it's slowing down my website. There's nothing more that can be done to improve this, I have already tested many configurations. As a solution, I was going to mount a RAM drive (tmpfs) that mirrors the GlusterFS web files but get the webserver to use the RAM drive. The issue is that I need two way realtime mirroring or replication between glusterfs and the RAM drive. I need this is as Apache writes files as wells. As I said, realtime two way synchronization across two folders. Which are in fact 2 different mounts points. The RAM (tmpfs) mount poing and the GlusterFS mount point. I already know about: Rsync - Which is one way Unison - Which is not realtime Please suggest me any solution free or paid. Thanks in advance

    Read the article

  • Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

    - by alexleonard
    I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

    Read the article

  • Requests are making it to my app server, but not into node.js -- why?

    - by Zane Claes
    I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

    Read the article

  • How to setup a hyper-v domain with internet access

    - by fynnbob
    First off let me say that I'm not a network admin or server guy, I know very little about that stuff. What I'm trying to do is setup a virtualized domain using hyper-V. Here is the configuration: Physical Server: 4Mb RAM Windows Server 2008 R2 running Hyper-V Virtual Environment: One Domain Controller running Windows Server 2008 R2 One Client running Windows Server 2008 R2 I have been successful in setting up a virtual domain controller and adding a virtual client to that domain controller but I'm stuck at trying to give the virtual Environment Internet access. I can give the client VM Internet access if I remove them from the virtual domain but once I add them back to the virtual domain, Internet access is gone. I've read articles describing many different ways this can be done (using RRAS with NAT, using a wireless connection, etc...) but all of those articles only cover a small piece of the setup and also seem to be geared towards people who know there way around networking and servers which I don't. I'd like to know more but my thing is software development and I have my hands full trying to keep up with everything in that realm. I simply want to setup a virtual domain with Internet access for testing. Can anyone point me to any "for Dummy's" type information on how to setup this type of environment or can anyone provide this kind of step-by-step help. Any help would be very much appreciated.

    Read the article

< Previous Page | 350 351 352 353 354 355 356 357 358 359 360 361  | Next Page >