Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 357/778 | < Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• NAT and ISP Subnet when load balancing on pfsense?

  - by dannymcc

  I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• Slow LAN transfer from 3rd party computer

  - by Chris

  Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

  Read the article

• Accessing the Internet via browser

  - by ucas

  I am on Windows 7 and using Firefox browser. I am using WiFi, but since the morning I cannot access the Internet via the browsers (Firefox, Chrome, or IE). The laptop shows there is Internet connection, Skype is online, but I can't reach the Internet. Then I launched Tor application which creates secure channel and provides its Firefox browser. Well, I can now access the Internet over that browser. So, what might be the problem causing this malfunction? The error: The connection has timed out The server at mail.google.com is taking too long to respond. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Best regards

  Read the article

• mac + parallels and https site test = router restarts

  - by Erik

  Ok I have an interesting & very frustrating problem happening. I'm going to explain it the best I can. I work as a graphic designer & web designer on a mac and have a Comcast internet connection that comes through a Comcast branded router (SMC8014) which then ties into an Airport Extreme Base Station which runs my office network. I run OS 10.5.7 and also run Parallels 4.0.3 (running Windows XP) for testing websites in Internet Explorer and so on. Ok, so that the basic background. Here's my issue. I've been collaborating an ecommerce website with another designer/developer and when testing the site on the PC side we have started to run into some sort of network problem. The site is https if that matters at all I suspect it may. Basically when I run parallels for testing I am constantly having to restart the router in order to connect to the test site (it's hosted). Funny thing is I can access the rest of the internet fine, just not this site I'm working on until I restart the router (It's sorta like the site is timing out). This never happens when just running the Mac side of things. It only becomes an issue when Parallels is open and I am doing page refreshes while making css or HTML edits via something like Coda or CSS edit (connected to the hosting server via ftp). The real problem is that once the problem starts I only get about 2 or 3 page loads before I have to restart the router again. It's absolutely crippling. I cannot get any work done when I have to restart the router every couple of minutes. So, if you think this problem is isolated to me, the answer is no. The designer/developer I'm collaborating with has an office a couple miles away and experiences very similar problems under slightly different setup. He also has Comcast as his internet provider and connects his router to an Airport and primarily works on a mac. The main difference is that rather than using a visualizer like parallels to test the website on the PC he uses a real live PC that is on his network. Once he fire up the PC to do testing he runs into the same issue described above. After a couple of page refreshes in Internet Explorer or other browser on the PC the site becomes unresponsive and the router has to get restarted. Any thoughts on what is going on here would be greatly appreciated. Thanks in advance.

  Read the article

• Issues connecting to WPA2 with User Authentication Mavericks?

  - by heinst

  I was on all the builds of the Mavericks beta and connecting to my University's network was fine. Then I upgraded to the public release and now I can't seem to connect to the internet. I can connect to other networks, but not my schools. Its a WPA2 network with a User Authentication. And my MacBook is a 2011? 2.2 GHz first gen i7 Quad Core with 8 GBs of RAM. Does anyone else have the same issue? Any tips on how to fix it? Thanks! heinst

  Read the article

• Windows 7 - Remote Desktop - multiple credentials

  - by w--

  My home network consists of a couple Windows XP machines and a Windows 7 box. One of the Windows XP boxes is like a shared server accessed via Remote Desktop. I have an account on there and my gf has another. Previously I was able to save RDC shortcuts to this shared server including credentials. So in order to access the server from a computer on the network, I just needed to open the shortcut. I thus would have two shortcuts, one for my account and one for my gf's. In Windows 7, it seems to store credentials for a box based on machine name. I.e. I can only store one set of credentials per machine name. This seems incredibly stupid so my question is: In Windows 7, is there some way to have RDC shortcuts that use different credentials to login to the same target box?

  Read the article

• Searching For a Desktop Security Software to harden Windows machines, anybody?

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So if anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• Naming your website longname.com vs shortcatchy.net vs shortcatchy.info

  - by jskye

  I'm designing a website that will basically be a social network for sharing information. I have the domain $$$$d.net and the same domain $$$$d.info where $$$$ is a word (that runs into the d) pertaining to the purpose of the site . The .com of this domain was already taken, but they've got nothing showing. They only have a not reached google error showing ie. dont seem to be trying to sell it either. I also have the long name of the site $$$$------&&&&&&&&&.com where the words $$$$ and &&&&&&&&& would contribute relevant seo to the site. In fact the word $$$$------ would also if a one letter spelling mistake is recognised at all by google, which i doubt but am unsure about. But as a brandname the $$$$------ word still works relevantly. Which do you think is a better choice to use? The short catchy name with the .info for relevance to information The .net which is more familiar than .info but slightly less relevant maybe. (But i think net as in network still works cos as i said it will be a social networking site). The long, .com domain which has more SEO plus a pun albeit on a spelling mistake. I know its kind of a subjective question and also hard to answer without knowing the name (which I've obfuscated because I'm only in initial design stage) but nevertheless im interested in what some of you guys think.

  Read the article

• "Play on another device" function not working with Samsung Allshare

  - by Tural Teyyuboglu

  Briefly I can't get work "Play on another device" function More detailed My Samsung TV (which support network) and PC are in the same network. The problem is, I can play PC contents from TV. But when I try to control TV remotely from Allshare software (PC), it shows TV only as connected device: But not as remote player in "players" list The result Tried to turn off firewall completely, reset router, re-install software. No success. Please help. BTW. On this link they kinda explained how to do it, but I software doesn' detect the TV as player in my case: http://www.samsung.com/global/allshare/pcsw/quickguide.html

  Read the article

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• ArchBeat Link-o-Rama for 2012-09-25

  - by Bob Rhubart

  Oracle 11gR2 RAC on Software Defined Network (SDN) | Gilbert Stan "The SDN [software defined network] idea is to separate the control plane and the data plane in networking and to virtualize networking the same way we have virtualized servers," explains Gil Standen. "This is an idea whose time has come because VMs and vmotion have created all kinds of problems with how to tell networking equipment that a VM has moved and to preserve connectivity to VPN end points, preserve IP, etc." H/T to Oracle ACE Director Tim Hall for the recommendation. ServerSent-Events on WebLogic Server | Steve Buttons "The HTML5 ServerSent-Event model provides a mechanism to allow browser clients to establish a uni-directional communication path to a server, where the server is then able to push messages to the browser at any point in time," explains Steve "Buttso" Buttons. Focus on Architects and Architecture This handy guide for sessions and other activities at Oracle OpenWorld 2012 focuses on IT architecture in all its many facets and permutations. Operating System Set-up for WebLogic Server | Rene van Wijk Oracle ACE Rene van Wijk shows you how to set-up an operating system for WebLogic Server. "We will use VMware as our virtualization platform and use CentOS as the operating system," says van Wijk. "We end the post by showing how the operating system can be tuned when running a Java process such as WebLogic Server." Free eBook: Oracle SOA Suite - In the Customer's Words If you find yourself in the position of having to sell the idea of Service-oriented Architecture to business stakeholders this free e-book may come in very handy. Check out "Oracle SOA Suite: In the Customer's Words. (Registration / Oracle.com login required.) Thought for the Day "The first rule of any technology used in a business is that automation applied to an efficient operation will magnify the efficiency. The second is that automation applied to an inefficient operation will magnify the inefficiency." — Bill Gates Source: BrainyQuote.com

  Read the article

• Configure IIS 6 to deny access to specific file based upon IP address

  - by victorferreira

  Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

  Read the article

• Is it possible to add tcp autotuning to windows xp?

  - by Caspin

  I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

  Read the article

• Is it possible to add tcp autotuning to windows xp?

  - by Caspin

  I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

  Read the article

• Windows Server 2008 R2 DNS Server not working?

  - by wolfvilleian

  I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• Frequent disconnects using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• Computers "applying computer settings" for a long time on start-up...why?

  - by tombull89

  Hello. Might be a bit of a slong shot but I'm stumped, along with the ICT Manager for the school I'm working it. In one of the IT rooms when you switch a computer on it will boot through BIOS fine, but when it gets to "applying computer settings" it can hang for a long time (~15 minutes). If you unplug the computer from the network it starts up fine, gets to the login screen, then you can plug the network cable in and it will work fine. I don't think it's anything to do with the fact we've been coming close to running out of IP addresses or a problem with our DHCP. Microsoft KB says apply the latest service pack, which we've done, and check a service. Servers and domian controllers are S2003, Computers and Desktops are XP. Does anybody have any thoughts on what to try?

  Read the article

• How to port forward https traffic via ssh and/or remote desktop to through several networks and PCs?

  - by donttellya

  I have the following environment: In company X I develop a application on a pc A in network A with ip address 192.168.100.50 which has to do an https request to an http server located in the intranet of company Y In company X is another pc B in network B with ip address 192.168.200.100 pc B (of company X) can access the intranet from company Y via ssh tunnel (putty) pc A (of company X) can ping pc B (of company X) note: pc A can also do a remote desktop connection to pc B) pc B can ping the http sever pc A can not ping the http server How can the https request from pc A of company X get to the http server of company Y? On which pc must be putty configured? And which settings for host, port forwarding etc. has to be done in putty? So finally the https request should go from PC A - PC B - Http Server in company Y.

  Read the article

• Get/Assign IP addresses assigned by the DHCP sever with DLink switches in between

  - by Ranjith Kumar

  In our office the setup is like we have a UBUNTU server with DHCP Server connected to all the PCS via 24 port and 8 port DLink switches. How can I find all the PCS(with client name, ip and mac address)in the network?? When I do "vi /var/lib/dhcp3/dhcpd.leases", I get all the ip addresses for the switches. I have used "arp-scan --interface=eth0 --localnet" to get all the IPs and MAC Addresses in my local network. I couldn't find any option to diplay client name. Also I would like to assign particular IP for a particular PC. I have done the changes in the dhcp.conf file but it is not working as they are not directly connected to DHCP-server(DLink switches in between). How can I assign IPs for PCs in this kind of setup. Thanks in advance

  Read the article

< Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >