Search Results

Search found 12907 results on 517 pages for 'todd little'.

Page 357/517 | < Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

  • Improve wireless performance

    - by djechelon
    Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

    Read the article

  • Running Flash on a headless Solaris box

    - by Marty Pitt
    Our build server is a Solaris box, and I'm trying to run a suite of FlexUnit tests as part of the automated build process. This works by compiling a swf movie with a suite of automated unit tests. The build script launches this movie, which automatically begins running the tests. Results of each test are sent back to the launching script across a port, and written out to a local xml file. Once the tests are completed, the movie closes down, and the build script interrogates the results to see if all the tests passed. The FlexUnit wiki provides information about how to to acheive this on a Unix server, by using Xvnc to provide a virtual space for the flash movie to run its tests in. I've provided this information through to our sys admin team, (along with the link to the article), and I've been told that because this is a Solaris box, we can't use that approach - Xvnc isn't supported on Solaris. Unfortunately, I know very little about servers, *nix vs Solaris, or Xvnc. Can someone please provide some advice about how we can achieve the same outcome on a Solaris box?

    Read the article

  • Internet Problem: Wireless connected but no connection to internet

    - by Josh K
    Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

    Read the article

  • Laptop Overheating with Windows 8

    - by Dany Khalife
    I recently installed Windows 8 on my HP G62 Laptop and i have been noticing a very strange problem with it. Let alone, for lets say 5 minutes, without even touching it, it starts to heat up and it reaches about 60 degrees (Celsius) with absolutely no applications open (not just on desktop but overall). I dug in a little deep and found out that Maintenance was running when the computer was Idle, so i turned that off From the System's Task Scheduler, and while there i also turned off other services i did not need hoping that would solve the problem. So after a few days, i noticed that the average temperature of my laptop dropped from 55 to 48 degrees while working on Visual Studio. And when i thought the problem had disappeared, it still did show up, only not after 5 minutes, but more like 10 minutes... Here is what i have done so far: Replacing the thermal paste on the CPU and the fan and cleaning the fan (this was like 6 months ago) Using a laptop cooler Running a virus scan (i just formatted my laptop so it would be really weird if i already caught something but who knows) Right now, i believe it has something to do with my gfx driver (Even though it IS up to date, looking closely at the screen, i can see the pixels slowly refresh (kinda like watching static on TV) which i wasn't able to do on Windows 7. If you have any ideas, let me know. Thanks

    Read the article

  • How can I keep SSH's know_hosts up to date (semi-securely)?

    - by Chas. Owens
    Just to get this out in front so I am not told not to do this: The machines in question are all on a local network with little to no internet access (they aren't even well connected to the corporate network) Everyone who has the ability to setup a man-in-the-middle attack already has root on the machine The machines are reinstalled as part of QA procedures, so having new host keys is important (we need to see how the other machines react); I am only trying to make my machine nicer to use. I do a lot of reinstalls on machines which changes their host keys. This necessitates going into ~/.ssh/known_hosts on my machine and blowing away to old key and adding the new key. This is a massive pain in the tuckus, so I have started considering ways to automate this. I don't want to just blindly accept any host key, so patching OpenSSH to ignore host keys is out. I have considered creating a wrapper around the ssh command the will detect the error coming back from ssh and present me with a prompt to delete the old key or quit. I have also considered creating a daemon that would fetch the latest host key from a machine on a whitelist (there are about twenty machines that are being constantly reinstalled) and replace the old host key in known_hosts. How would you automate this process?

    Read the article

  • Internet Troubles - PPPoE vs PPPoA?

    - by AkkA
    I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

    Read the article

  • Wireless router setup for 1-1 NAT

    - by Carlos
    What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

    Read the article

  • Looking to get a small server – need web, PHP, PostgreSQL.

    - by Javawag
    Hi all! I'm looking to get a cheap (low end) server to serve web pages (xHTML/PHP), but I also need to be able to set up PostGreSQL on the system too. Ideally the server would have low power consumption, run Linux (I prefer Mac OS X but a Mac Mini, although the size I'm looking for, is too much money!) and be around £100 (~$160US). EDIT: Just to make it clearer, I'm looking to purchase the server hardware myself – but I want something about Mac Mini sized. I don't want to pay for hosting! Also, quick question – if it's to serve web pages from my home (standard ISP connection, no static IP!), what do I need in place to get this working. I'm guessing I would sign up with some service like no-ip, and register a domain to point to my no-ip address (then install the no-ip software on the server to update that with the current IP). I know the idea of running a server behind a normal ISP connection isn't very elegant, but I'd prefer to have the server where I can see it then pay over the odds for a hosting service where I have little to no control over what happens. Also, I could write my own server software for apps/etc to connect to as well. Anyways I'm rambling! What do you guys think?! Javawag

    Read the article

  • HP/Lenovo alternative to Buffalo iSCSI TerraStation?

    - by Robin Day
    I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/Lenovo? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

    Read the article

  • When should NTPd broadcast/broadcastclient be used instead of client/server or peer modes?

    - by Luke404
    The NTP deamon if often used in its simplest mode, which is client/server: you specify one or more server directives in your ntp.conf and your clients will use those servers. In addition to that, when you run your own NTP servers, it is good practice to peer them together, so if one of them looses connectivity to its upstream servers, it will get time from its peers. But NTPd can also work with broadcast and/or multicast distribution of time data, with the documentation stating: broadcast and multicast modes are intended for configurations involving one or a few servers and a possibly very large client population The documentation also says elsewhere: It is possible and frequently useful to configure a host as both broadcast client and broadcast server. A number of hosts configured this way and sharing a common broadcast address will automatically organize themselves in an optimum configuration based on stratum and synchronization distance. I can see one obvious administrative benefit: you don't have to manually specify and update your list of NTP servers in the clients ntp.conf, so to me it looks tempting to use broadcast mode even for a small client population (say 5+ clients with 3~4 servers). I expect network traffic to be a little higher with broadcasts instead of client/server associations, but given the usual gigabit ethernet LAN the impact should be negligible unless you have a very very large number of hosts in the same broadcast domain. At the end of the day, when should broadcast mode be used or avoided? Are there pros and cons I haven't seen?

    Read the article

  • Web browsing through SSH tunnel gets stuck/clogged

    - by endolith
    I use tools like Tunnelier to log into my home Tomato router through SSH, and then use it as a proxy for web browsing, tunnel for Remote Desktop/VNC, etc. Most days it works great, but some days every page I try to view gets stuck, like the tunnel is clogged. I load a web page and it seems to be loading, then stops, with the little loading icon spinning and nothing happening. I refresh the page, I reboot the router, I reboot the other computers on my home network and turn off any bandwidth-hogging services on them, I've turned on QoS on the router to prioritize SSH. I don't understand what's getting stuck. Rebooting or disconnecting/reconnecting the SSH tunnel improves responsiveness for a minute, but then it gets clogged again. It also seems to help if I don't do anything on the tunnel for a few minutes, then it will be responsive for a bit and then get clogged again. Trying to open a terminal console from Tunnelier is also unresponsive, so it's not just a web browsing problem. Likewise, connecting to http://192.168.1.1 in the browser (to the router's web config through its own tunnel) is also slow/laggy/halting. The realtime bandwidth reported by the router is nowhere near my DSL connection's limits, though it does show big spikes during the laggy times, and the connection is responsive when it shows low bandwidths. How do I troubleshoot something like this?

    Read the article

  • Fedora installed in Legacy mode, how to make it work in UEFI?

    - by TryntaLearn
    I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

    Read the article

  • Exchange 2010 OWA- Open Other User Mailbox

    - by Benjamin Jones
    I just started working for this small firm (30 people) a little bit ago, replacing their System Admin. First thing I noticed was Exchange Server 2010 was WAY out of date. Believe it or not they did not have SP1 installed. So after I installed and configured Exchange 2010 SP3 and redirected OWA I noticed something in OWA. I could add ANYONE's User Mailbox WITHOUT giving mailbox premission. I created a couple test users, same thing. I even had another employee provide me access to their OWA and they could open anyone's Inbox without granting permission. I don't want to play the blame game, but I was SHOCKED that this was going on. Luckly being such a small company I'll be able to cover this mistake that I did not create, BUT HOW? My guess is that I need to find out where the past System Admin went wrong in providing Full Access Permission? Or could this be a Auto-Mapping issue? I found this article: http://technet.microsoft.com/en-us/library/hh529943.aspx This might work $FixAutoMapping = Get-MailboxPermission sharedmailbox |where {$_.AccessRights -eq "FullAccess" -and $_.IsInherited -eq $false} $FixAutoMapping | Remove-MailboxPermission $FixAutoMapping | ForEach {Add-MailboxPermission -Identity $_.Identity -User $_.User -AccessRights:FullAccess -AutoMapping $false} However how do I insert the above code into Powershell? Again I was thrown into this mess and I'm just trying to iron out this tangled mess.

    Read the article

  • SamFS performance problem on file creation

    - by Gregor Longariva
    I have two samfs filesystems (samfs1 and samfs2), both on the same 6130, both with the same config/watermarks/timeouts etc. creating a file on samfs2 works as it should, on samfs1 not. A little simple script shows up, that every while and then the file creation needs between 11 and 28 seconds: stan 12:32 [scratch]# while ( 1 ) while? echo - while? time echo test file while? time mv file file2 while? echo + while? sleep 1 while? end 0.00u 0.00s 0:00.01 0.0% 0.00u 0.00s 0:00.00 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.03 0.0% + 0.00u 0.00s 0:23.71 0.0% 0.00u 0.00s 0:00.14 0.0% + 0.00u 0.00s 0:00.18 0.0% 0.00u 0.00s 0:00.13 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.06 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.04 0.0% + 0.00u 0.00s 0:00.04 0.0% 0.00u 0.00s 0:00.05 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.01 0.0% + 0.00u 0.00s 0:26.05 0.0% 0.00u 0.00s 0:00.50 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.06 0.0% + 0.00u 0.00s 0:00.00 0.0% 0.00u 0.00s 0:00.12 0.0% + Any idea where the problem could be?

    Read the article

  • Hadoop streaming job on EC2 stays in "pending" state

    - by liamf
    Trying to experiment with Hadoop and Streaming using cloudera distribution CDH3 on Ubuntu. Have valid data in hdfs:// ready for processing. Wrote little streaming mapper in python. When I launch a mapper only job using: hadoop jar /usr/lib/hadoop/contrib/streaming/hadoop-streaming*.jar -file /usr/src/mystuff/mapper.py -mapper /usr/src/mystuff/mapper.py -input /incoming/STBFlow/* -output testOP hadoop duly decides it will use 66 mappers on the cluster to process the data. The testOP directory is created on HDFS. A job_conf.xml file is created. But the job tracker UI at port 50030 never shows the job moving out of "pending" state and nothing else happens. CPU usage stays at zero. (the job is created though) If I give it a single file (instead of the entire directory) as input, same result (except Hadoop decides it needs 2 mappers instead of 66). I also tried using the "dumbo" Python utility and launching jobs using that: same result: permanently pending. So I am missing something basic: could someone help me out with what I should look for? The cluster is on Amazon EC2. Firewall issues maybe: ports are enabled explicitly, case by case, in the cluster security group.

    Read the article

  • SQL Server Installation: Is it 32 or 64 bit?

    - by CapBBeard
    Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

    Read the article

  • Disk usage on IIS, PHP5, performance problems.

    - by Jacob84
    Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

    Read the article

  • Liked Arch Linux - but I am still not sure if its the right distro for me...

    - by BlackAndGold
    As the title says... I used Arch Linux for a while and liked it a lot: leightweight, sleek, fast and well documented with a great community. However I had to format my hd and for the sake of being too lazy to reinstall arch, I used windows 7 exclusively for a while. Now I want to get back to linux again (still dual boot), mainly for web development purposes and using handy tools such as rsync ect. Again, I liked Arch, but there is too much tweeking, too much reading up and too much figuring out what to do as well es some bad suprises especially when you need them the least and when just quickly want to get some work done. I kind of would like to have a little more "out of the box" distro that is still fast and somewhat leighweight and of course reliable. I actually considered Ubuntu, which I am not too big of a fan of, but I will still give the minimal install a shot. However other distros seem interesting as well, such as crunchbang and mint debian ecpecially. My question, hoping this isn't too boring for many you, what is the right distro for me?

    Read the article

  • Removing extended partition without deleting logical in it

    - by HisDudeness
    I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

    Read the article

  • IP tables blocking access to most hosts but some accesses being logged

    - by epo
    What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

    Read the article

  • how to diagnose a hard system seizure? Dell+Ubuntu

    - by rob
    I've got Ubuntu 9.10 on a Dell Vostro 420 desktop, a little over a year old, which I use for plain vanilla work stuff (email, web, terminal, text editor). Every now and then, at totally random times, it completely freezes on me. Hard. Mouse and keyboard stop working, cursor stops blinking, clock stops moving. All I can do is hold down the power button on the front of the box to shut it off. Sometimes it happens after several months of continuous uptime; sometimes it happens a few minutes after a reboot, while all I've done is open a terminal to look at log files, or maybe firefox to do a google search. Each time, there is nothing at all in /var/log/messages at the time of the crash. This makes it seem like a hardware problem, and indeed a few months ago I opened the box and wiggled everything and the problem went away for a while. But now it's back. I went in and checked everything, took out each RAM card and reseated. No luck. I ran all the system diagnostics (the long version) and everything passed with flying colors. Something is messed up in this box, but without any useful logs or failed tests, how in the world am I going to find it? And of course, Dell's not gonna help me cause I went and replaced Windows with Ubuntu. What steps would you take next to track down this problem?

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Things to check for an internet-facing email server.

    - by Shtééf
    I'm faced with the task of setting up a public-internet-facing email server, that will be relaying mail for all of our other servers in the network. While the software in itself is set up in few keystrokes, what little experience I have with managing an email server has thought me that there are tons of awkward filtering techniques employed by other email systems. Systems that my own server will inevitably interact with a some point. Hence, my questions: What things should be kept in mind and double checked when setting up an email server? What resources are available for checking if my email server is set-up correctly? I'm specifically NOT looking for instructions for any given mail server, such as Exchange or Postfix. But it's okay to say: “you should have X and Y in your set-up, because when talking to server software Z, it typically tries to weed out open relays by checking for these.” Some things I've discovered myself: Make sure forward and reverse DNS are set up. Mail servers tend to do a reverse lookup for the peer IP-address when receiving. Matching a reverse look up with a follow-up forward lookup is probably employed to weed out open relays run through malware on home networks. Make sure the user in the From-address exists. The From-address is easily spoofed. A receiving mail server may try to contact the mail server in the From-domain, and see if the From-user actually exists.

    Read the article

< Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >