Search Results

Search found 2968 results on 119 pages for 'cable modem'.

Page 36/119 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• DD-WRT RIP2 Router mode configuration

  - by Eduardo

  Can anybody tell me why my wireless router only redirects traffic to ADSL modem when it is on Gateway mode? These are the configurations when it is on RIP2 Router mode: ADSL Modem: ------------ LAN IP: 10.1.1.1 Subnet mask: 255.0.0.0 RIP v2 enabled in both directions Route: destination: 192.168.1.0 Subnet mask: 255.255.255.0 Gateway: 10.1.1.2 Wireless Router (DD-WRT) ------------------------ WAN IP: 10.1.1.2 WAN Subnet mask: 255.0.0.0 LAN IP: 192.168.1.1 LAN Subnet mask: 255.255.255.0 Operating mode: RIP2 Router Static Route: Destination LAN NET: 10.0.0.0 Subnet Mask: 255.0.0.0 Gateway: 10.1.1.1 Interface: LAN & WLAN

  Read the article

• port forwarding? [closed]

  - by Nrew

  Possible Duplicate: Configure Modem for Bittorrent downloads any guides on portforwarding? I want to speed up my torrent downloads

  Read the article

• DD-WRT Router acting as a Switch and Wi-Fi AP

  - by dotnetchris

  Recently I upgraded to Comcast Business and their modem has a built-in router so I took off my DD-WRT router and moved to a location in my home where I needed more ports and Wi-Fi (preferably without running new Ethernet cables since it's 50-100 foot run through floor and ceilings). I have my network cable from my Comcast modem going into Port 1 of my DD-WRT router with Port 2 and 3 being networked PCs. I have DD-WRT setup as a DHCP forwarder with the firewall disabled. This lets my all of my devices access the network fine. Is the correct the way to do this? Or is this a less optimal solution and it should be done in a slightly different way?

  Read the article

• Setup LAN to serve webpages and voip and access to the web site from inside LAN with domain name

  - by Mauricio Arias

  I'd like to know if it will work: I have my domain and I´m serving a webpage in a nginx to the internet, but if I type my domain in my laptop inside LAN I access to my modem/router configuration, I cannot access to the web server unless I type the IP address. I would like to add a Bind server after the modem/router - (port forward, ports 80 and 5060), if the request is www.mydomain.com bind should resolve the nginx IP address and serve it, and if it is a voip request should address to the voip server and if I'd like to access to the website from inside LAN I'd like to type mydomain.com. Could I do it with this configuration? Do I need something else? Thanks in advace!

  Read the article

• Configuring VLAN's on two HP procurve switches

  - by pan

  Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this ISP is coming through my internal network, I plan on using a new vlan called "airspeed" only for this ISP traffic. Up until now I've just been using the Default_vlan on both HP switches (4108 + 2524). So far I've been unable to ping from my laptop to the ISP modem both of which are on the new vlan 2 ("Airspeed"). No traffic needs to cross from vlan 2 to vlan 1 so I've left the ports as untagged. I've used the subnet provide from my ISP as the new vlan 2 subnet. Can anybody see what I'm doing wrong here? I've added the configuration of both switch below. Rough diagram: Microwave modem (Gateway IP 77.75.00.49) | HP 2524 switch (port 24) | HP 2524 switch fibre link | HP 4108GL switch fibre link | HP 4108GL switch (port D1) | Laptop configured with IP 77.75.00.50 (for testing but will be connected to firewall) And my 4108GL config: ; J4865A Configuration Editor; Created on release #G.07.21 hostname "HP ProCurve Switch 4108GL" cdp run module 1 type J4864A module 2 type J4862B module 3 type J4862B module 4 type J4862B ip default-gateway 128.1.146.50 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged A1-A3,B1-B24,C1-C24,D2-D24 ip address 128.1.146.203 255.255.0.0 no untagged D1 exit vlan 2 name "Airspeed" untagged D1 ip address 77.75.00.51 255.255.255.248 exit Finally my 2524 config: ; J4813A Configuration Editor; Created on release #F.04.08 hostname "HP ProCurve Switch 2524" cdp run ip default-gateway 0.0.0.0 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.51 "public" snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged 1-23,25-26 no untagged 24 ip address 128.1.146.204 255.255.0.0 exit vlan 2 name "Airspeed" untagged 24 ip address 77.75.00.51 255.255.255.248 exit no aaa port-access authenticator active

  Read the article

• How to check a digital certificate?

  - by StackedCrooked

  I have extracted a certificate from a cable modem. Now I want to verify if this certificate is valid. If I understand correctly, the verification process consists of having the issuer sign the subject's public key and then comparing the result with the subject's signature. This signing process is done using the issuer's private key, which nobody but the issuer has access to. So even if I have both certificates on my PC, there is no way for me to verify the subject's validity. From this I can only conclude that the verification must be implemented as a remote service. The problem is that I don't know what remote service I need to access to verify this certificate. The issuer is "AVM GmbH Cable Modem Root Certificate Authority". How can I find the webservice for verification? Is there standard lookup mechanism for this?

  Read the article

• Internet speed is suddenly slow only on my laptop, but it's normal in other devices

  - by Wael

  I have a TP-Link router connected to a ZTE modem, with 2 laptops, a tablet, 2 phones connected via the router's WiFi, and an additional desktop connected via ethernet to the router. Today, my laptop started to have a very slow connection to the internet, which at first I thought it was the operator's problem to find out later on that it works fine on other devices. I tried to connect directly via WiFi to the modem, but it was as slow. I cannot access facebook at all, google takes forever to do a search, and youtube barely works. The weird thing though, is that when youtube does work, the streaming is full speed. This happens also when I download a file! My browse is Firefox, but I used Chrome and IE9 with the same results. I work on Windows 7 Thanks for any advices.

  Read the article

• Using watch to run a shell script - but the script goes defunct

  - by PHP-Steven

  So I want to keep an eye on my network connectivity so I can make a report for my ISP. (seems like the modem goes out for about 30-60 seconds about once a day) So I copied this handy little script http://www.cyberciti.biz/tips/simple-linux-and-unix-system-monitoring-with-ping-command-and-scripts.html And an running it with watch -n 15 ./ping-test.sh I have been testing it by pulling the plug on my modem. The first time watch runs the script after the network goes out it runs fine (sends some email) and then goes defunct. Once networking is restored the script "finishes" and then watch runs it again. So I'm getting mail for when the network goes down, but not how long it was down for. If I run the script straight from the command line it runs (emails) and then exits. Any ideas why? How can I get the script to keep running once the network is down?

  Read the article

• Network bottleneck/throttling issue

  - by Gavin

  Hi all, It's my first day at a new company and i've been given the task to find out an issue with the internet connection. I noticed that whilst I was downloading a large file, the network grinds to a halt, except for my download. At first I thought it was the internet connection/modem but it seems that whilst the lockdown occurs, I am unable to access any network device. Has anyone experienced this before and if so, do you have any pointers? Looking at the setup. They have an DSL modem that connects to a 10/100 switch. There are only 5-6 computers on the network. Cheers Gavin

  Read the article

• Shareing two internet connections on my laptop running Windows XP

  - by ashwnacharya

  I have two internet connections, one is internet via our organization's corporate LAN network, and the other one is mobile broadband via a USB modem Is there anyway I can share internet connections and use them simultaneously? I want to use the corporate LAN network for normal browsing and connecting my email client, and I want to use the USB modem for establishing a VPN connection. Will I be able to maintain both the connections simultaneously? Can I have parallel downloads, one using our corporate network, and the other one using the mobile broadband? Will I be able to switch my browser between these two connections? My laptop runs Windows XP Service Pack 2.

  Read the article

• Why do the IP addresses randomly change?

  - by GiddyUpHorsey

  I have a network with the following: Cable modem with static IP address Router Desktop - Win 7 VM Host - VMware ESXi 4.0 A couple of VM Guests - Windows Every now and then my Win 7 PC is unable to access some of the VMs. When I ping the VMs by their domain name their IP address shows up as the IP address of the cable modem. Sometimes I can fix it by running ipconfig /flushdns. The IP address will reset back to what it was supposed to be, but occasionally it wont work. Why does this happen and how can I fix it?

  Read the article

• ADSL connetion (BSNL dataone) with puppy Linux

  - by Vaibhav Garg

  I have an old PC which I want to use for internet browsing. I tried using Puppy Linux (version 4.3.1) for the same but have not been able to connect. I connect via PPPoE. My network card is RTL 8029b which is automatically detected by Puppy Linux. However, the LED indicator on the MODEM designating LAN connectivity stays off. This post is being typed from the same PC running XP, so there are no connection issues. I am a complete newbie for Linux. can somebody point me to instructions. I will be willing to give any more information if required. P.S. My MODEM is Huewei Smartax MT 882 Thanks

  Read the article

• How can I speed up my Windows Server 2008 VPN Connection?

  - by Pure.Krome

  So I've installed VPN service that comes with Windows Server 2008. Works perfectly, etc. When a client remote desktops to one of the private servers at the office, via VPN .. it's pretty slow. Now - how long is a piece of string? So before I get all the obligatory checks, I'll list the things from Mr. Obvious: Our modem/router (fritz!box) has a data/graph that shows incoming and outbound bandwidth. Both directions are barely getting used when a client has RDP'd via VPN. Our office internet connection is running at 21,9 Mbit/s download 1,3 Mbit/s upload. I feel like it's maxing at .. modem speeds ?? Is there any tricks I can do to confirm this and possibly even fix this?

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• What's the point of Netgear's WNHDB3004 "3DHD WIRELESS HOME THEATER NETWORKING KIT"

  - by badp

  Here's a crude representation of what I've got at home: floor 2 INTERNETS ---- MODEM/ROUTER ---- MY COMPUTER | floor 1 WIFI REPEATER ---- stuff | floor 0 more stuff TELEVISION Now, as part of our sat tv subscription we can get an additional service if we connect our decoder (located by TELEVISION obviously) to the internet. What they suggest is buying a Netgear 3DHD WIRELESS HOME THEATER NETWORKING KIT holy shit isn't my bullshit-o-meter flying high right now from the general buzzwordyness of this thing. What does this thing actually do that our existing wireless-enabled routers don't do? What's the point of having a third wifi router in the same house, this time only for one television? If I do decide to plunge €99 for this, should I connect it to the wifi repeater (which does not provide AAA quality internet, at least for all gaming purposes) or to my modem/router (risking issues with low signal?).

  Read the article

• Motorola SBG6850 / Linksys WRT54G network problem

  - by user96407

  I am trying to resolve issues with connecting my desktop and LAN capable printer to my network. I recently upgrade to the Motorola Cable Modem Gateway SBG6580 and have TWC coming into it, this works great for wired and wireless connectivity. Although, I am unable to connect to my device from this modem gateway. So, I am trying to cable a Linksys WRT54G (firmware 4.21.4 build 0) to the backside of the SBG6850 so I can use my printer on my network from both my wired desktop and wireless devices. I am pulling wireless off of the SBG6580 and do not want to change this. I have disable the wireless feature on the Linksys WRT54G at this moment. Can someone please help me through this dilemma? I am open to both wired and wireless solutions, but please tell me which approach your sharing in the first line of your response. Cheers!

  Read the article

• Upgrading my home network to Gigabit Ethernet and Wireless-N turns out slower than before

  - by Raheel Khan

  My home network has three desktops, three laptops and some NAS drives. All desktops and NAS drives support Gigabit LAN and all laptops support Wireless-N. I was running a 100 BaseT switch though. I recently purchased a Gigabit Ethernet Switch and an Wireless-N ADSL Modem-Router. After upgrading, I noticed that the wireless file transfer speeds from laptop-to-NAS and vice versa became terribly slow. Possibly even slower than before the upgrade. The transfer speeds from desktop-to-NAS (wired) have improved though. As an example, copying a 50GB file from laptop-to-NAS was estimated at 15 hours! Is there something I can do to improve this? Also, should I consider buying a dedicated wireless access point for speed rather than using the Wireless modem-router?

  Read the article

• Connect to internet through DC with 2 network interfaces

  - by Ali Foroughi

  I have a network like this : Client 1 <== Wireless ==> Access Point <== Wire ==> DC <== Wireless ==> ADSL Modem Client 1 : IP : 192.168.1.181 DG : 192.168.1.100 DNS : 192.168.1.100 Access Point : IP : 192.168.1.10 DG : 192.168.1.100 DC : IP : 192.168.1.100 DG : 192.168.1.1 DNS : 127.0.0.1 ADSL Modem : IP : 192.168.1.1 I can ping yahoo.com from client1, but cannot browse the internet. UPDATE1 : my DC has two network interfaces that I bridge together. UPDATE2 : I powered down the DC firewall UPDATE3 : I set a forwarder for my DC to 8.8.8.8 (Google dns)

  Read the article

• Should I install Windows 7 on a 3 years old PC?

  - by Jitendra vyas

  This is my PC configuration, Should I upgrade my Windows XP to Windows 7. Currently I'm using Windows XP SP3 32 bit. Now will I get same performance or better performance or bad performance if I install Windows 7 on this system? Or would sticking with XP be better? Memory (RAM): 1472 MB DDR RAM (not DDR 2) CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1398.7 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Network Adapters: Bluetooth Device (Personal Area Network) | WAN (PPP/SLIP) Interface Hard Disks: 300 GB SATA HDD Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA :

  Read the article

• change ip address verizon fios [closed]

  - by John Smith

  One well documented way to change a dynamically assigned ip address is to log into the router configuration settings and change the mac address , disconnect the router and modem, and to turn it all back on. This actually worked with a basic modem connected by ethernet directly to a laptop, spoofing laptop mac address, with a cable internet provider. Now this question is specific to fiber optic internet providers who bundle with tv and internet (verizon fios, comcast xfinity). Verizon fios installation comes with an actiontec router, and there is a built in way to clone the mac address in the router configuration settings. What will happen if the mac address changes from what verizon installed it as? Will they get angry and disconnect service? Will other services other than internet stop working (tv or phone)?

  Read the article

• Firewall software that can block access to certain applications on certain internet connections

  - by webmasters

  I have two internet connections, a LAN and a 3G modem on a Windows 7 machine. The LAN is connected to a Edimax router which is conneted to the ISP (with their own modem). Now, the Edimax router is set to auto assign IP adresses in the range: 168.192.2.100 and 192.168.2.200 I wanted to block internet explorer to access the LAN. I entered my AVG firewall, selected iexplorer and added a "block" rule which blocked all ports, TCP and UDP protocols for the above IP range. The problem is it did not work, not matter what rules I have tried. Can you recommend a firewall that can easily accomplish this? Ty

  Read the article

• Permanent Routes Centos Questions

  - by user65053

  So with a little help I figured out how to setup these routes and I can set them in rc.local route add -net 208.82.236.0 netmask 255.255.255.0 dev ppp0 metric 1 route add -net 208.82.236.0 netmask 255.255.255.0 dev eth0 metric 10 my question is being that the first route is ppp0 as soon as I disconnect the modem the route is dropped how do I maintain the route or make it permanent so that next time the modem connects it will follow the route. Currently after ppp0 disconnects the route is dropped netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface laxapx03.o1.com * 255.255.255.255 UH 0 0 0 ppp0 208.82.236.0 * 255.255.255.0 U 0 0 0 eth0 10.0.1.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 default 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• European wireless data

  - by drewk

  I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

  Read the article

• Windows Fax Server Leaves Documents in "Pending" Status

  - by Chris

  We are having an issue with Windows Fax Server on Windows Server 2008. Occasionally, the server will get into a state where after adding jobs to the outbox, they will simply remain at the pending status (without any attempt to send them). There is nothing in the event log mentioning a problem. It typically seems to enter the state after restarting the server or after no faxes have been sent for a while. The way to fix the issue has been to: Stop the Fax service Go into the modem properties in device manager and query modem Start the Fax service - at which point all the pending faxes in the outbox will send.

  Read the article

• Laptop with internal serial port in 2009 (and 2010)

  - by Vincent Demeester

  Are there any computer vendors (like Dell, Lenovo, or..) that still sell laptops with an internal serial port? We are using several modem and other kind of box at work that have to be used (and/or programmed) with serial port (RS232, DB9, ..). We tried many usb/pcmcia serial adapter which run fine when used to load programs on the boxes but not with modems. The protocol behind the RTC connection (with modem) need timer we are not able to reach when using an adapter (maybe until we find a very good adapter), and that leads to my question..

  Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >