Search Results

Search found 951 results on 39 pages for 'surface'.

Page 36/39 | < Previous Page | 32 33 34 35 36 37 38 39  | Next Page >

  • A faulty Caviar Blue hard drive?

    - by Glister
    We have a small "homemade" server running fully updated Debian Wheezy (amd64). One hard drive installed: WDC WD6400AAKS. The motherboard is ASUS M4N68T V2. The usual load: CPU: an average of 20% Each week about 50GB of additional space is occupied. About 47GB of uploaded files and 3GB of MySQL data. I'm afraid that the hard drive may be about to fail. I saw Pre-fail on few places when I ran: root@SERVER:/tmp# smartctl -a /dev/sda smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD6400AAKS-XXXXXXX Serial Number: WD-XXXXXXXXXXXXXXXXXXX LU WWN Device Id: 5 0014ee XXXXXXXXXXXXX Firmware Version: 01.03B01 User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Oct 28 18:55:27 2013 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 247) Self-test routine in progress... 70% of test remaining. Total time to complete Offline data collection: (11580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 136) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 157 146 021 Pre-fail Always - 5108 4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2968 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 051 Old_age Always - 0 9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 15445 10 Spin_Retry_Count 0x0032 100 100 051 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2950 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 426 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2968 194 Temperature_Celsius 0x0022 111 095 000 Old_age Always - 36 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 160 000 Old_age Always - 21716 200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 15444 - Error SMART Read Selective Self-Test Log failed: scsi error aborted command Smartctl: SMART Selective Self Test Log Read Failed root@SERVER:/tmp# In one tutorial I read that the pre-fail is a an indication of coming failure, in another tutorial I read that it is not true. Can you guys help me decode the output of smartctl? It would be also nice to share suggestions what should I do if I want to ensure data integrity (about 50GB of new data each week, up to 2TB for the whole period I'm interested in). Maybe I will go with 2x2TB Caviar Black in RAID4?

    Read the article

  • Writing the tests for FluentPath

    - by Bertrand Le Roy
    Writing the tests for FluentPath is a challenge. The library is a wrapper around a legacy API (System.IO) that wasn’t designed to be easily testable. If it were more testable, the sensible testing methodology would be to tell System.IO to act against a mock file system, which would enable me to verify that my code is doing the expected file system operations without having to manipulate the actual, physical file system: what we are testing here is FluentPath, not System.IO. Unfortunately, that is not an option as nothing in System.IO enables us to plug a mock file system in. As a consequence, we are left with few options. A few people have suggested me to abstract my calls to System.IO away so that I could tell FluentPath – not System.IO – to use a mock instead of the real thing. That in turn is getting a little silly: FluentPath already is a thin abstraction around System.IO, so layering another abstraction between them would double the test surface while bringing little or no value. I would have to test that new abstraction layer, and that would bring us back to square one. Unless I’m missing something, the only option I have here is to bite the bullet and test against the real file system. Of course, the tests that do that can hardly be called unit tests. They are more integration tests as they don’t only test bits of my code. They really test the successful integration of my code with the underlying System.IO. In order to write such tests, the techniques of BDD work particularly well as they enable you to express scenarios in natural language, from which test code is generated. Integration tests are being better expressed as scenarios orchestrating a few basic behaviors, so this is a nice fit. The Orchard team has been successfully using SpecFlow for integration tests for a while and I thought it was pretty cool so that’s what I decided to use. Consider for example the following scenario: Scenario: Change extension Given a clean test directory When I change the extension of bar\notes.txt to foo Then bar\notes.txt should not exist And bar\notes.foo should exist This is human readable and tells you everything you need to know about what you’re testing, but it is also executable code. What happens when SpecFlow compiles this scenario is that it executes a bunch of regular expressions that identify the known Given (set-up phases), When (actions) and Then (result assertions) to identify the code to run, which is then translated into calls into the appropriate methods. Nothing magical. Here is the code generated by SpecFlow: [NUnit.Framework.TestAttribute()] [NUnit.Framework.DescriptionAttribute("Change extension")] public virtual void ChangeExtension() { TechTalk.SpecFlow.ScenarioInfo scenarioInfo = new TechTalk.SpecFlow.ScenarioInfo("Change extension", ((string[])(null))); #line 6 this.ScenarioSetup(scenarioInfo); #line 7 testRunner.Given("a clean test directory"); #line 8 testRunner.When("I change the extension of " + "bar\\notes.txt to foo"); #line 9 testRunner.Then("bar\\notes.txt should not exist"); #line 10 testRunner.And("bar\\notes.foo should exist"); #line hidden testRunner.CollectScenarioErrors();} The #line directives are there to give clues to the debugger, because yes, you can put breakpoints into a scenario: The way you usually write tests with SpecFlow is that you write the scenario first, let it fail, then write the translation of your Given, When and Then into code if they don’t already exist, which results in running but failing tests, and then you write the code to make your tests pass (you implement the scenario). In the case of FluentPath, I built a simple Given method that builds a simple file hierarchy in a temporary directory that all scenarios are going to work with: [Given("a clean test directory")] public void GivenACleanDirectory() { _path = new Path(SystemIO.Path.GetTempPath()) .CreateSubDirectory("FluentPathSpecs") .MakeCurrent(); _path.GetFileSystemEntries() .Delete(true); _path.CreateFile("foo.txt", "This is a text file named foo."); var bar = _path.CreateSubDirectory("bar"); bar.CreateFile("baz.txt", "bar baz") .SetLastWriteTime(DateTime.Now.AddSeconds(-2)); bar.CreateFile("notes.txt", "This is a text file containing notes."); var barbar = bar.CreateSubDirectory("bar"); barbar.CreateFile("deep.txt", "Deep thoughts"); var sub = _path.CreateSubDirectory("sub"); sub.CreateSubDirectory("subsub"); sub.CreateFile("baz.txt", "sub baz") .SetLastWriteTime(DateTime.Now); sub.CreateFile("binary.bin", new byte[] {0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0xFF}); } Then, to implement the scenario that you can read above, I had to write the following When: [When("I change the extension of (.*) to (.*)")] public void WhenIChangeTheExtension( string path, string newExtension) { var oldPath = Path.Current.Combine(path.Split('\\')); oldPath.Move(p => p.ChangeExtension(newExtension)); } As you can see, the When attribute is specifying the regular expression that will enable the SpecFlow engine to recognize what When method to call and also how to map its parameters. For our scenario, “bar\notes.txt” will get mapped to the path parameter, and “foo” to the newExtension parameter. And of course, the code that verifies the assumptions of the scenario: [Then("(.*) should exist")] public void ThenEntryShouldExist(string path) { Assert.IsTrue(_path.Combine(path.Split('\\')).Exists); } [Then("(.*) should not exist")] public void ThenEntryShouldNotExist(string path) { Assert.IsFalse(_path.Combine(path.Split('\\')).Exists); } These steps should be written with reusability in mind. They are building blocks for your scenarios, not implementation of a specific scenario. Think small and fine-grained. In the case of the above steps, I could reuse each of those steps in other scenarios. Those tests are easy to write and easier to read, which means that they also constitute a form of documentation. Oh, and SpecFlow is just one way to do this. Rob wrote a long time ago about this sort of thing (but using a different framework) and I highly recommend this post if I somehow managed to pique your interest: http://blog.wekeroad.com/blog/make-bdd-your-bff-2/ And this screencast (Rob always makes excellent screencasts): http://blog.wekeroad.com/mvc-storefront/kona-3/ (click the “Download it here” link)

    Read the article

  • The blocking nature of aggregates

    - by Rob Farley
    I wrote a post recently about how query tuning isn’t just about how quickly the query runs – that if you have something (such as SSIS) that is consuming your data (and probably introducing a bottleneck), then it might be more important to have a query which focuses on getting the first bit of data out. You can read that post here.  In particular, we looked at two operators that could be used to ensure that a query returns only Distinct rows. and The Sort operator pulls in all the data, sorts it (discarding duplicates), and then pushes out the remaining rows. The Hash Match operator performs a Hashing function on each row as it comes in, and then looks to see if it’s created a Hash it’s seen before. If not, it pushes the row out. The Sort method is quicker, but has to wait until it’s gathered all the data before it can do the sort, and therefore blocks the data flow. But that was my last post. This one’s a bit different. This post is going to look at how Aggregate functions work, which ties nicely into this month’s T-SQL Tuesday. I’ve frequently explained about the fact that DISTINCT and GROUP BY are essentially the same function, although DISTINCT is the poorer cousin because you have less control over it, and you can’t apply aggregate functions. Just like the operators used for Distinct, there are different flavours of Aggregate operators – coming in blocking and non-blocking varieties. The example I like to use to explain this is a pile of playing cards. If I’m handed a pile of cards and asked to count how many cards there are in each suit, it’s going to help if the cards are already ordered. Suppose I’m playing a game of Bridge, I can easily glance at my hand and count how many there are in each suit, because I keep the pile of cards in order. Moving from left to right, I could tell you I have four Hearts in my hand, even before I’ve got to the end. By telling you that I have four Hearts as soon as I know, I demonstrate the principle of a non-blocking operation. This is known as a Stream Aggregate operation. It requires input which is sorted by whichever columns the grouping is on, and it will release a row as soon as the group changes – when I encounter a Spade, I know I don’t have any more Hearts in my hand. Alternatively, if the pile of cards are not sorted, I won’t know how many Hearts I have until I’ve looked through all the cards. In fact, to count them, I basically need to put them into little piles, and when I’ve finished making all those piles, I can count how many there are in each. Because I don’t know any of the final numbers until I’ve seen all the cards, this is blocking. This performs the aggregate function using a Hash Match. Observant readers will remember this from my Distinct example. You might remember that my earlier Hash Match operation – used for Distinct Flow – wasn’t blocking. But this one is. They’re essentially doing a similar operation, applying a Hash function to some data and seeing if the set of values have been seen before, but before, it needs more information than the mere existence of a new set of values, it needs to consider how many of them there are. A lot is dependent here on whether the data coming out of the source is sorted or not, and this is largely determined by the indexes that are being used. If you look in the Properties of an Index Scan, you’ll be able to see whether the order of the data is required by the plan. A property called Ordered will demonstrate this. In this particular example, the second plan is significantly faster, but is dependent on having ordered data. In fact, if I force a Stream Aggregate on unordered data (which I’m doing by telling it to use a different index), a Sort operation is needed, which makes my plan a lot slower. This is all very straight-forward stuff, and information that most people are fully aware of. I’m sure you’ve all read my good friend Paul White (@sql_kiwi)’s post on how the Query Optimizer chooses which type of aggregate function to apply. But let’s take a look at SQL Server Integration Services. SSIS gives us a Aggregate transformation for use in Data Flow Tasks, but it’s described as Blocking. The definitive article on Performance Tuning SSIS uses Sort and Aggregate as examples of Blocking Transformations. I’ve just shown you that Aggregate operations used by the Query Optimizer are not always blocking, but that the SSIS Aggregate component is an example of a blocking transformation. But is it always the case? After all, there are plenty of SSIS Performance Tuning talks out there that describe the value of sorted data in Data Flow Tasks, describing the IsSorted property that can be set through the Advanced Editor of your Source component. And so I set about testing the Aggregate transformation in SSIS, to prove for sure whether providing Sorted data would let the Aggregate transform behave like a Stream Aggregate. (Of course, I knew the answer already, but it helps to be able to demonstrate these things). A query that will produce a million rows in order was in order. Let me rephrase. I used a query which produced the numbers from 1 to 1000000, in a single field, ordered. The IsSorted flag was set on the source output, with the only column as SortKey 1. Performing an Aggregate function over this (counting the number of rows per distinct number) should produce an additional column with 1 in it. If this were being done in T-SQL, the ordered data would allow a Stream Aggregate to be used. In fact, if the Query Optimizer saw that the field had a Unique Index on it, it would be able to skip the Aggregate function completely, and just insert the value 1. This is a shortcut I wouldn’t be expecting from SSIS, but certainly the Stream behaviour would be nice. Unfortunately, it’s not the case. As you can see from the screenshots above, the data is pouring into the Aggregate function, and not being released until all million rows have been seen. It’s not doing a Stream Aggregate at all. This is expected behaviour. (I put that in bold, because I want you to realise this.) An SSIS transformation is a piece of code that runs. It’s a physical operation. When you write T-SQL and ask for an aggregation to be done, it’s a logical operation. The physical operation is either a Stream Aggregate or a Hash Match. In SSIS, you’re telling the system that you want a generic Aggregation, that will have to work with whatever data is passed in. I’m not saying that it wouldn’t be possible to make a sometimes-blocking aggregation component in SSIS. A Custom Component could be created which could detect whether the SortKeys columns of the input matched the Grouping columns of the Aggregation, and either call the blocking code or the non-blocking code as appropriate. One day I’ll make one of those, and publish it on my blog. I’ve done it before with a Script Component, but as Script components are single-use, I was able to handle the data knowing everything about my data flow already. As per my previous post – there are a lot of aspects in which tuning SSIS and tuning execution plans use similar concepts. In both situations, it really helps to have a feel for what’s going on behind the scenes. Considering whether an operation is blocking or not is extremely relevant to performance, and that it’s not always obvious from the surface. In a future post, I’ll show the impact of blocking v non-blocking and synchronous v asynchronous components in SSIS, using some of LobsterPot’s Script Components and Custom Components as examples. When I get that sorted, I’ll make a Stream Aggregate component available for download.

    Read the article

  • The blocking nature of aggregates

    - by Rob Farley
    I wrote a post recently about how query tuning isn’t just about how quickly the query runs – that if you have something (such as SSIS) that is consuming your data (and probably introducing a bottleneck), then it might be more important to have a query which focuses on getting the first bit of data out. You can read that post here.  In particular, we looked at two operators that could be used to ensure that a query returns only Distinct rows. and The Sort operator pulls in all the data, sorts it (discarding duplicates), and then pushes out the remaining rows. The Hash Match operator performs a Hashing function on each row as it comes in, and then looks to see if it’s created a Hash it’s seen before. If not, it pushes the row out. The Sort method is quicker, but has to wait until it’s gathered all the data before it can do the sort, and therefore blocks the data flow. But that was my last post. This one’s a bit different. This post is going to look at how Aggregate functions work, which ties nicely into this month’s T-SQL Tuesday. I’ve frequently explained about the fact that DISTINCT and GROUP BY are essentially the same function, although DISTINCT is the poorer cousin because you have less control over it, and you can’t apply aggregate functions. Just like the operators used for Distinct, there are different flavours of Aggregate operators – coming in blocking and non-blocking varieties. The example I like to use to explain this is a pile of playing cards. If I’m handed a pile of cards and asked to count how many cards there are in each suit, it’s going to help if the cards are already ordered. Suppose I’m playing a game of Bridge, I can easily glance at my hand and count how many there are in each suit, because I keep the pile of cards in order. Moving from left to right, I could tell you I have four Hearts in my hand, even before I’ve got to the end. By telling you that I have four Hearts as soon as I know, I demonstrate the principle of a non-blocking operation. This is known as a Stream Aggregate operation. It requires input which is sorted by whichever columns the grouping is on, and it will release a row as soon as the group changes – when I encounter a Spade, I know I don’t have any more Hearts in my hand. Alternatively, if the pile of cards are not sorted, I won’t know how many Hearts I have until I’ve looked through all the cards. In fact, to count them, I basically need to put them into little piles, and when I’ve finished making all those piles, I can count how many there are in each. Because I don’t know any of the final numbers until I’ve seen all the cards, this is blocking. This performs the aggregate function using a Hash Match. Observant readers will remember this from my Distinct example. You might remember that my earlier Hash Match operation – used for Distinct Flow – wasn’t blocking. But this one is. They’re essentially doing a similar operation, applying a Hash function to some data and seeing if the set of values have been seen before, but before, it needs more information than the mere existence of a new set of values, it needs to consider how many of them there are. A lot is dependent here on whether the data coming out of the source is sorted or not, and this is largely determined by the indexes that are being used. If you look in the Properties of an Index Scan, you’ll be able to see whether the order of the data is required by the plan. A property called Ordered will demonstrate this. In this particular example, the second plan is significantly faster, but is dependent on having ordered data. In fact, if I force a Stream Aggregate on unordered data (which I’m doing by telling it to use a different index), a Sort operation is needed, which makes my plan a lot slower. This is all very straight-forward stuff, and information that most people are fully aware of. I’m sure you’ve all read my good friend Paul White (@sql_kiwi)’s post on how the Query Optimizer chooses which type of aggregate function to apply. But let’s take a look at SQL Server Integration Services. SSIS gives us a Aggregate transformation for use in Data Flow Tasks, but it’s described as Blocking. The definitive article on Performance Tuning SSIS uses Sort and Aggregate as examples of Blocking Transformations. I’ve just shown you that Aggregate operations used by the Query Optimizer are not always blocking, but that the SSIS Aggregate component is an example of a blocking transformation. But is it always the case? After all, there are plenty of SSIS Performance Tuning talks out there that describe the value of sorted data in Data Flow Tasks, describing the IsSorted property that can be set through the Advanced Editor of your Source component. And so I set about testing the Aggregate transformation in SSIS, to prove for sure whether providing Sorted data would let the Aggregate transform behave like a Stream Aggregate. (Of course, I knew the answer already, but it helps to be able to demonstrate these things). A query that will produce a million rows in order was in order. Let me rephrase. I used a query which produced the numbers from 1 to 1000000, in a single field, ordered. The IsSorted flag was set on the source output, with the only column as SortKey 1. Performing an Aggregate function over this (counting the number of rows per distinct number) should produce an additional column with 1 in it. If this were being done in T-SQL, the ordered data would allow a Stream Aggregate to be used. In fact, if the Query Optimizer saw that the field had a Unique Index on it, it would be able to skip the Aggregate function completely, and just insert the value 1. This is a shortcut I wouldn’t be expecting from SSIS, but certainly the Stream behaviour would be nice. Unfortunately, it’s not the case. As you can see from the screenshots above, the data is pouring into the Aggregate function, and not being released until all million rows have been seen. It’s not doing a Stream Aggregate at all. This is expected behaviour. (I put that in bold, because I want you to realise this.) An SSIS transformation is a piece of code that runs. It’s a physical operation. When you write T-SQL and ask for an aggregation to be done, it’s a logical operation. The physical operation is either a Stream Aggregate or a Hash Match. In SSIS, you’re telling the system that you want a generic Aggregation, that will have to work with whatever data is passed in. I’m not saying that it wouldn’t be possible to make a sometimes-blocking aggregation component in SSIS. A Custom Component could be created which could detect whether the SortKeys columns of the input matched the Grouping columns of the Aggregation, and either call the blocking code or the non-blocking code as appropriate. One day I’ll make one of those, and publish it on my blog. I’ve done it before with a Script Component, but as Script components are single-use, I was able to handle the data knowing everything about my data flow already. As per my previous post – there are a lot of aspects in which tuning SSIS and tuning execution plans use similar concepts. In both situations, it really helps to have a feel for what’s going on behind the scenes. Considering whether an operation is blocking or not is extremely relevant to performance, and that it’s not always obvious from the surface. In a future post, I’ll show the impact of blocking v non-blocking and synchronous v asynchronous components in SSIS, using some of LobsterPot’s Script Components and Custom Components as examples. When I get that sorted, I’ll make a Stream Aggregate component available for download.

    Read the article

  • smartctl -t long isn't finishing

    - by xenoterracide
    I been running smartctl -t long on a drive for about 2 days now and it seems to be stalled at 10%. short and conveyance both passed. I have to send 1 of 2 drives purchased back I found badblocks with badblocks (none on this drive and I'ts made over a pass already). I'm just wondering if I should be concerned about this. smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WMAV51582123 Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon May 10 22:19:52 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 241) Self-test routine in progress... 10% of test remaining. Total time to complete Offline data collection: (20100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 231) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2 3 Spin_Up_Time 0x0027 131 131 021 Pre-fail Always - 6408 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 148 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 10 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 174 194 Temperature_Celsius 0x0022 106 102 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 99 - # 2 Extended offline Interrupted (host reset) 10% 30 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

    Read the article

  • SSAO Distortion

    - by Robert Xu
    I'm currently (attempting) to add SSAO to my engine, except it's...not really work, to say the least. I use a deferred renderer to render my scene. I have four render targets: Albedo, Light, Normal, and Depth. Here are the parameters for all of them (Surface Format, Depth Format): Albedo: 32-bit ARGB, Depth24Stencil8 Light: 32-bit ARGB, None Normal: 32-bit ARGB, None Depth: 8-bit R (Single), Depth24Stencil8 To generate my random noise map for the SSAO, I do the following for each pixel in the noise map: Vector3 v3 = Vector3.Zero; double z = rand.NextDouble() * 2.0 - 1.0; double r = Math.Sqrt(1.0 - z * z); double angle = rand.NextDouble() * MathHelper.TwoPi; v3.X = (float)(r * Math.Cos(angle)); v3.Y = (float)(r * Math.Sin(angle)); v3.Z = (float)z; v3 += offset; v3 *= 0.5f; result[i] = new Color(v3); This is my GBuffer rendering effect: PixelInput RenderGBufferColorVertexShader(VertexInput input) { PixelInput pi = ( PixelInput ) 0; pi.Position = mul(input.Position, WorldViewProjection); pi.Normal = mul(input.Normal, WorldInverseTranspose); pi.Color = input.Color; pi.TPosition = pi.Position; pi.WPosition = input.Position; return pi; } GBufferTarget RenderGBufferColorPixelShader(PixelInput input) { GBufferTarget output = ( GBufferTarget ) 0; float3 position = input.TPosition.xyz / input.TPosition.w; output.Albedo = lerp(float4(1.0f, 1.0f, 1.0f, 1.0f), input.Color, ColorFactor); output.Normal = EncodeNormal(input.Normal); output.Depth = position.z; return output; } And here is the SSAO effect: float4 EncodeNormal(float3 normal) { return float4((normal.xyz * 0.5f) + 0.5f, 0.0f); } float3 DecodeNormal(float4 encoded) { return encoded * 2.0 - 1.0f; } float Intensity; float Size; float2 NoiseOffset; float4x4 ViewProjection; float4x4 ViewProjectionInverse; texture DepthMap; texture NormalMap; texture RandomMap; const float3 samples[16] = { float3(0.01537562, 0.01389096, 0.02276565), float3(-0.0332658, -0.2151698, -0.0660736), float3(-0.06420016, -0.1919067, 0.5329634), float3(-0.05896204, -0.04509097, -0.03611697), float3(-0.1302175, 0.01034653, 0.01543675), float3(0.3168565, -0.182557, -0.01421785), float3(-0.02134448, -0.1056605, 0.00576055), float3(-0.3502164, 0.281433, -0.2245609), float3(-0.00123525, 0.00151868, 0.02614773), float3(0.1814744, 0.05798516, -0.02362876), float3(0.07945167, -0.08302628, 0.4423518), float3(0.321987, -0.05670302, -0.05418307), float3(-0.00165138, -0.00410309, 0.00537362), float3(0.01687791, 0.03189049, -0.04060405), float3(-0.04335613, -0.00530749, 0.06443053), float3(0.8474263, -0.3590308, -0.02318038), }; sampler DepthSampler = sampler_state { Texture = DepthMap; MipFilter = Point; MinFilter = Point; MagFilter = Point; AddressU = Clamp; AddressV = Clamp; AddressW = Clamp; }; sampler NormalSampler = sampler_state { Texture = NormalMap; MipFilter = Linear; MinFilter = Linear; MagFilter = Linear; AddressU = Clamp; AddressV = Clamp; AddressW = Clamp; }; sampler RandomSampler = sampler_state { Texture = RandomMap; MipFilter = Linear; MinFilter = Linear; MagFilter = Linear; }; struct VertexInput { float4 Position : POSITION0; float2 TextureCoordinates : TEXCOORD0; }; struct PixelInput { float4 Position : POSITION0; float2 TextureCoordinates : TEXCOORD0; }; PixelInput SSAOVertexShader(VertexInput input) { PixelInput pi = ( PixelInput ) 0; pi.Position = input.Position; pi.TextureCoordinates = input.TextureCoordinates; return pi; } float3 GetXYZ(float2 uv) { float depth = tex2D(DepthSampler, uv); float2 xy = uv * 2.0f - 1.0f; xy.y *= -1; float4 p = float4(xy, depth, 1); float4 q = mul(p, ViewProjectionInverse); return q.xyz / q.w; } float3 GetNormal(float2 uv) { return DecodeNormal(tex2D(NormalSampler, uv)); } float4 SSAOPixelShader(PixelInput input) : COLOR0 { float depth = tex2D(DepthSampler, input.TextureCoordinates); float3 position = GetXYZ(input.TextureCoordinates); float3 normal = GetNormal(input.TextureCoordinates); float occlusion = 1.0f; float3 reflectionRay = DecodeNormal(tex2D(RandomSampler, input.TextureCoordinates + NoiseOffset)); for (int i = 0; i < 16; i++) { float3 sampleXYZ = position + reflect(samples[i], reflectionRay) * Size; float4 screenXYZW = mul(float4(sampleXYZ, 1.0f), ViewProjection); float3 screenXYZ = screenXYZW.xyz / screenXYZW.w; float2 sampleUV = float2(screenXYZ.x * 0.5f + 0.5f, 1.0f - (screenXYZ.y * 0.5f + 0.5f)); float frontMostDepthAtSample = tex2D(DepthSampler, sampleUV); if (frontMostDepthAtSample < screenXYZ.z) { occlusion -= 1.0f / 16.0f; } } return float4(occlusion * Intensity * float3(1.0, 1.0, 1.0), 1.0); } technique SSAO { pass Pass0 { VertexShader = compile vs_3_0 SSAOVertexShader(); PixelShader = compile ps_3_0 SSAOPixelShader(); } } However, when I use the effect, I get some pretty bad distortion: Here's the light map that goes with it -- is the static-like effect supposed to be like that? I've noticed that even if I'm looking at nothing, I still get the static-like effect. (you can see it in the screenshot; the top half doesn't have any geometry yet it still has the static-like effect) Also, does anyone have any advice on how to effectively debug shaders?

    Read the article

  • Pet Peeves with the Windows Phone 7 Marketplace

    - by Bil Simser
    Have you ever noticed how something things just gnaw at your very being. This is the case with the WP7 marketplace, the Zune software, and the things that drive me batshit crazy with a side of fries. To go. I wanted to share. XBox Live is Not the Centre of the Universe Okay, it’s fine that the Zune software has an XBox live tag for games so can see them clearly but do we really need to have it shoved down our throats. On every click? Click on Games in the marketplace: The first thing that it defaults to on the filters on the right is XBox Live: Okay. Fine. However if you change it (say to Paid) then click onto a title when you come back from that title is the filter still set to Paid? No. It’s back to XBox Live again. Really? Give us a break. If you change to any filter on any other genre then click on the selected title, it doesn’t revert back to anything. It stays on the selection you picked. Let’s be fair here. The Games genre should behave just like every other one. If I pick Paid then when I come back to the list please remember that. Double Dipping On the subject of XBox Live titles, Microsoft (and developers who have an agreement with Microsoft to produce Live titles, which generally rules out indie game developers) is double dipping with regards to exposure of their titles. Here’s the Puzzle and Trivia Game section on the Marketplace for XBox Live titles: And here’s the same category filtered on Paid titles: See the problem? Two indie titles while the rest are XBox Live ones. So while XBL has it’s filter, they also get to showcase their wares in the Paid and Free filters as well. If you’re going to have an XBox Live filter then use it and stop pushing down indie titles until they’re off the screen (on some genres this is already the case). Free and Paid titles should be just that and not include XBox Live ones. If you’re really stoked that people can’t find the Free XBox Live titles vs. the paid ones, then create a Free XBox Live filter and a Paid XBox Live filter. I don’t think we would mind much. Whose Trial is it Anyways? You might notice apps in the marketplace with titles like “My Fart App Professional Lite” or “Silicon Lamb Spleen Builder Free”. When you submit and app to the marketplace it can either be free or paid. If it’s a paid app you also have the option to submit it with Trial capabilities. It’s up to you to decide what you offer in the trial version but trial versions can be purchased from within the app so after someone trys out your app (for free) and wants to unlock the Super Secret Obama Spy Ring Level, they can just go to the marketplace from your app (if you built that functionality in) and upgrade to the paid version. However it creates a rift of sorts when it comes to visibility. Some developers go the route of the paid app with a trial version, others decide to submit *two* apps instead of one. One app is the “Free” or “Lite” verions and the other is the paid version. Why go to the hassle of submitting two apps when you can just create a trial version in the same app? Again, visibility. There’s no way to tell Paid apps with Trial versions and ones without (it’s an option, you don’t have to provide trial versions, although I think it’s a good idea). However there is a way to see the Free apps from the Paid ones so some submit the two apps and have the Free version have links to buy the paid one (again through the Marketplace tasks in the API). What we as developers need for visibility is a new filter. Trial. That’s it. It would simply filter on Paid apps that have trial capabilities and surface up those apps just like the free ones. If Microsoft added this filter to the marketplace, it would eliminate the need for people to submit their “Free” and “Lite” versions and make it easier for the developer not to have to maintain two systems. I mean, is it really that hard? Can’t be any more difficult than the XBox Live Filter that’s already there. Location is Everything The last thing on my bucket list is about location. When I launch Zune I’m running in my native location setting, Canada. What’s great is that I navigate to the Travel Tools section where I have one of my apps and behold the splendour that I see: There are my apps in the number 1 and number 4 slot for top selling in that category. I show it to my wife to make up for the sleepless nights writing this stuff and we dance around and celebrate. Then I change my location on my operation system to United States and re-launch Zune. WTF? My flight app has slipped to the 10th spot (I’m only showing 4 across here out of the 7 in Zune) and my border check app that was #1 is now in the 32nd spot! End of celebration. Not only is relevance being looked at here, I value the comments people make on may apps as do most developers. I want to respond to them and show them that I’m listening. The next version of my border app will provide multiple camera angles. However when I’m running in my native Canada location, I only see two reviews. Changing over to United States I see fourteen! While there are tools out there to provide with you a unified view, I shouldn’t have to rely on them. My own Zune desktop software should allow me to see everything. I realize that some developers will submit an app and only target it for some locations and that’s their choice. However I shouldn’t have to jump through hoops to see what apps are ahead of mine, or see people comments and ratings. Another proposal. Either unify the marketplace (i.e. when I’m looking at it show me everything combined) or let me choose a filter. I think the first option might be difficult as you’re trying to average out top selling apps across all markets and have to deal with some apps that have been omitted from some markets. Although I think you could come up with a set of use cases that would handle that, maybe that’s too much work. At the very least, let us developers view the markets in a drop down or something from within the Zune desktop. Having to shut down Zune, change our location, and re-launch Zune to see other perspectives is just too onerous. A Call to Action These are just one mans opinion. Do you agree? Disagree? Feel hungry for a bacon sandwich? Let everyone know via the comments below. Perhaps someone from Microsoft will be reading and take some of these ideas under advisement. Maybe not, but at least let’s get the word out that we really want to see some change. Egypt can do it, why not WP7 developers!

    Read the article

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Announcing: Improvements to the Windows Azure Portal

    - by ScottGu
    Earlier today we released a number of enhancements to the new Windows Azure Management Portal.  These new capabilities include: Service Bus Management and Monitoring Support for Managing Co-administrators Import/Export support for SQL Databases Virtual Machine Experience Enhancements Improved Cloud Service Status Notifications Media Services Monitoring Support Storage Container Creation and Access Control Support All of these improvements are now live in production and available to start using immediately.  Below are more details on them: Service Bus Management and Monitoring The new Windows Azure Management Portal now supports Service Bus management and monitoring. Service Bus provides rich messaging infrastructure that can sit between applications (or between cloud and on-premise environments) and allow them to communicate in a loosely coupled way for improved scale and resiliency. With the new Service Bus experience, you can now create and manage Service Bus Namespaces, Queues, Topics, Relays and Subscriptions. You can also get rich monitoring for Service Bus Queues, Topics and Subscriptions. To create a Service Bus namespace, you can now select the “Service Bus” tab in the Windows Azure portal and then simply select the CREATE command: Doing so will bring up a new “Create a Namespace” dialog that allows you to name and create a new Service Bus Namespace: Once created, you can obtain security credentials associated with the Namespace via the ACCESS KEY command. This gives you the ability to obtain the connection string associated with the service namespace. You can copy and paste these values into any application that requires these credentials: It is also now easy to create Service Bus Queues and Topics via the NEW experience in the portal drawer.  Simply click the NEW command and navigate to the “App Services” category to create a new Service Bus entity: Once you provision a new Queue or Topic it can be managed in the portal.  Clicking on a namespace will display all queues and topics within it: Clicking on an item in the list will allow you to drill down into a dashboard view that allows you to monitor the activity and traffic within it, as well as perform operations on it. For example, below is a view of an “orders” queue – note how we now surface both the incoming and outgoing message flow rate, as well as the total queue length and queue size: To monitor pub/sub subscriptions you can use the ADD METRICS command within a topic and select a specific subscription to monitor. Support for Managing Co-Administrators You can now add co-administrators for your Windows Azure subscription using the new Windows Azure Portal. This allows you to share management of your Windows Azure services with other users. Subscription co-administrators share the same administrative rights and permissions that service administrator have - except a co-administrator cannot change or view billing details about the account, nor remove the service administrator from a subscription. In the SETTINGS section, click on the ADMINISTRATORS tab, and select the ADD button to add a co-administrator to your subscription: To add a co-administrator, you specify the email address for a Microsoft account (formerly Windows Live ID) or an organizational account, and choose the subscription you want to add them to: You can later update the subscriptions that the co-administrator has access to by clicking on the EDIT button, and then select or deselect the subscriptions to which they belong. Import/Export Support for SQL Databases The Windows Azure administration portal now supports importing and exporting SQL Databases to/from Blob Storage.  Databases can be imported/exported to blob storage using the same BACPAC file format that is supported with SQL Server 2012.  Among other benefits, this makes it easy to copy and migrate databases between on-premise and cloud environments. SQL Databases now have an EXPORT command in the bottom drawer that when pressed will prompt you to save your database to a Windows Azure storage container: The UI allows you to choose an existing storage account or create a new one, as well as the name of the BACPAC file to persist in blob storage: You can also now import and create a new SQL Database by using the NEW command.  This will prompt you to select the storage container and file to import the database from: The Windows Azure Portal enables you to monitor the progress of import and export operations. If you choose to log out of the portal, you can come back later and check on the status of all of the operations in the new history tab of the SQL Database server – this shows your entire import and export history and the status (success/fail) of each: Enhancements to the Virtual Machine Experience One of the common pain-points we have heard from customers using the preview of our new Virtual Machine support has been the inability to delete the associated VHDs when a VM instance (or VM drive) gets deleted. Prior to today’s release the VHDs would continue to be in your storage account and accumulate storage charges. You can now navigate to the Disks tab within the Virtual Machine extension, select a VM disk to delete, and click the DELETE DISK command: When you click the DELETE DISK button you have the option to delete the disk + associated .VHD file (completely clearing it from storage).  Alternatively you can delete the disk but still retain a .VHD copy of it in storage. Improved Cloud Service Status Notifications The Windows Azure portal now exposes more information of the health status of role instances.  If any of the instances are in a non-running state, the status at the top of the dashboard will summarize the status (and update automatically as the role health changes): Clicking the instance hyperlink within this status summary view will navigate you to a detailed role instance view, and allow you to get more detailed health status of each of the instances.  The portal has been updated to provide more specific status information within this detailed view – giving you better visibility into the health of your app: Monitoring Support for Media Services Windows Azure Media Services allows you to create media processing jobs (for example: encoding media files) in your Windows Azure Media Services account. In the Windows Azure Portal, you can now monitor the number of encoding jobs that are queued up for processing as well as active, failed and queued tasks for encoding jobs. On your media services account dashboard, you can visualize the monitoring data for last 6 hours, 24 hours or 7 days. Storage Container Creation and Access Control Support You can now create Windows Azure Storage storage containers from within the Windows Azure Portal.  After selecting a storage account, you can navigate to the CONTAINERS tab and click the ADD CONTAINER command: This will display a dialog that lets you name the new container and control access to it: You can also update the access setting as well as container metadata of existing containers by selecting one and then using the new EDIT CONTAINER command: This will then bring up the edit container dialog that allows you to change and save its settings: In addition to creating and editing containers, you can click on them within the portal to drill-in and view blobs within them.  Summary The above features are all now live in production and available to use immediately.  If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using them today.  Visit the Windows Azure Developer Center to learn more about how to build apps with it. We’ll have even more new features and enhancements coming later this month – including support for the recent Windows Server 2012 and .NET 4.5 releases (we will enable new web and worker role images with Windows Server 2012 and .NET 4.5, and support .NET 4.5 with Websites).  Keep an eye out on my blog for details as these new features become available. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

    Read the article

  • Thoughts on Build 2013

    - by D'Arcy Lussier
    Originally posted on: http://geekswithblogs.net/dlussier/archive/2013/06/30/153294.aspxAnd so another Build conference has come to an end. Below are my thoughts/perspectives on various aspects of the event. I’ll do a separate blog post on my thoughts of the Build message for developers. The Good Moscone center was a great venue for Build! Easy to get around, easy to get to, and well maintained, it was a very comfortable conference venue. Yeah, the free swag was nice. Build has built up an expectation that attendees will always get something; it’ll be interesting to see how Microsoft maintains this expectation over the next few Build events. I still maintain that free swag should never be the main reason one attends an event, and for me this was definitely just an added bonus. I’m planning on trying to use the Surface as a dedicated 2nd device at work for meetings, I’ll share my experiences over the next few months. The hackathon event was a great idea, although personally I couldn’t justify spending the money on a conference registration just to spend the entire conference coding. Still, the apps that were created were really great and there was a lot of passion and excitement around the hackathon. I wonder if they couldn’t have had the hackathon on the Monday/Tuesday for those that wanted to participate so they didn’t miss any of the actual conference over Wed/Thurs. San Francisco was a great city to host Build. Getting from hotels to the conference center was very easy (well especially for me, I was only 3 blocks away) and the city itself felt very safe. However, if I never have to fly into SFO again I’ll be alright with that! Delays going into and out of SFO and both apparently were due to the airport itself. The Bad Build is one of those oddities on the conference landscape where people will pay to commit to attending an event without knowing anything about the sessions. We got our list of conference sessions when we registered on Tuesday, not before. And even then, we only got titles and not descriptions (those were eventually made available via the conference’s mobile application). I get it…they’re going to make announcements and they don’t want to give anything away through the session titles. But honestly, there wasn’t anything in the session titles that I would have considered a surprise. Breakfasts were brutal. High-carb pastries, donuts, and muffins with fruit and hard boiled eggs does not a conference breakfast make. I can’t believe that the difference between a continental breakfast per person and a hot breakfast buffet would have been a huge impact to a conference fee that was already around $2000. The vendor area was anemic. I don’t know why Microsoft forces the vendors into cookie-cutter booth areas (this year they were all made of plywood material). WPC, TechEd – booth areas there allow the vendors to be creative with their displays. Not so much for Build. Really odd was the lack of Microsoft’s own representation around Bing. In the day 1 keynote Microsoft made a big deal about Bing as an API. Yet there was nobody in the vendor area set up to provide more information or have discussions with about the Bing API. The Ugly Our name badges were NFC enabled. The purpose of this, beyond the vendors being able to scan your info, wasn’t really made clear. An attendee I talked to showed how you could get a reader app on your phone so you can scan other members cards and collect their contact info – which is a kewl idea; business cards are so 1990’s. But I was *shocked* at the amount of information that was on our name badges! Here’s what’s displayed on our name badge: - Name - Company - Twitter Handle I’m ok with that. But here’s what actually gets read: - Name - Company - Address Used for Registration - Phone Number Used for Registration So sharing that info with another attendee, they get way more of my info than just how to find me on Twitter! Microsoft, you need to fix this for the future. If vendors want to collect information on attendees, they should be able to collect an ID from the badge, then get a report with corresponding records afterwards. My personal information should not be so readily available, and without my knowledge! Final Verdict Maybe its my older age, maybe its where I’m at in life with family, maybe its where I’m at in my career, but when I consider whether a conference experience was valuable I get to the core reason I attend: opportunities to learn, opportunities to network, opportunities to engage with Microsoft. Opportunities to Learn:  Sessions I attended were generally OK, with some really stand out ones on Day 2. I would love to see Microsoft adopt the Dojo format for a portion of their sessions. Hands On Labs are dull, lecture style sessions are great for information sharing. But a guided hands-on coding session (Read: Dojo) provides the best of both worlds. Being that all content is publically available online to everyone (Build attendee or not), the value of attending the conference sessions is decreased. The value though is in the discussions that take part in person afterwards, which leads to… Opportunities to Network: I enjoyed getting together with old friends and connecting with Twitter friends in person for the first time. I also had an opportunity to meet total strangers. So from a networking perspective, Build was fantastic! I still think it would have been great to have an area for ad-hoc discussions – where speakers could announce they’d be available for more questions after their sessions, or attendees who wanted to discuss more in depth on a topic with other attendees could arrange space. Some people have no problems being outgoing and making these things happen, but others are not and a structured model is more attractive. Opportunities to Engage with Microsoft: Hit and miss on this one. Outside of the vendor area, unless you cornered or reached out to a speaker, there wasn’t any defined way to connect with blue badges. And as I mentioned above, Microsoft didn’t have full representation in the vendor area (no Bing). All in all, Build was a fun party where I was informed about some new stuff and got some free swag. Was it worth the time away from home and the hit to my PD budget? I’d say Somewhat. Build is a great informational conference, but I wouldn’t call it a learning conference. Considering that TechEd seems to be moving to more of an IT Pro focus, independent developer conferences seem to be the best value for those looking to learn and not just be informed. With the rapid development cycle Microsoft is embracing, we’re already seeing Build happening twice within a 12 month period. If that continues, the value of attending Build in person starts to diminish – especially with so much content available online. If Microsoft wants Build to be a must-attend event in the future, they need to start incorporating aspects of Tech Ed, past PDCs, and other conferences so those that want to leave with more than free swag have something to attract them.

    Read the article

  • Developing Mobile Applications: Web, Native, or Hybrid?

    - by Michelle Kimihira
    Authors: Joe Huang, Senior Principal Product Manager, Oracle Mobile Application Development Framework  and Carlos Chang, Senior Principal Product Director The proliferation of mobile devices and platforms represents a game-changing technology shift on a number of levels. Companies must decide not only the best strategic use of mobile platforms, but also how to most efficiently implement them. Inevitably, this conversation devolves to the developers, who face the task of developing and supporting mobile applications—not a simple task in light of the number of devices and platforms. Essentially, developers can choose from the following three different application approaches, each with its own set of pros and cons. Native Applications: This refers to apps built for and installed on a specific platform, such as iOS or Android, using a platform-specific software development kit (SDK).  For example, apps for Apple’s iPhone and iPad are designed to run specifically on iOS and are written in Xcode/Objective-C. Android has its own variation of Java, Windows uses C#, and so on.  Native apps written for one platform cannot be deployed on another. Native apps offer fast performance and access to native-device services but require additional resources to develop and maintain each platform, which can be expensive and time consuming. Mobile Web Applications: Unlike native apps, mobile web apps are not installed on the device; rather, they are accessed via a Web browser.  These are server-side applications that render HTML, typically adjusting the design depending on the type of device making the request.  There are no program coding constraints for writing server-side apps—they can be written in Java, C, PHP, etc., it doesn’t matter.  Instead, the server detects what type of mobile browser is pinging the server and adjusts accordingly. For example, it can deliver fully JavaScript and CSS-enabled content to smartphone browsers, while downgrading gracefully to basic HTML for feature phone browsers. Mobile apps work across platforms, but are limited to what you can do through a browser and require Internet connectivity. For certain types of applications, these constraints may not be an issue. Oracle supports mobile web applications via ADF Faces (for tablets) and ADF Mobile browser (Trinidad) for smartphone and feature phones. Hybrid Applications: As the name implies, hybrid apps combine technologies from native and mobile Web apps to gain the benefits each. For example, these apps are installed on a device, like their pure native app counterparts, while the user interface (UI) is based on HTML5.  This UI runs locally within the native container, which usually leverages the device’s browser engine.  The advantage of using HTML5 is a consistent, cross-platform UI that works well on most devices.  Combining this with the native container, which is installed on-device, provides mobile users with access to local device services, such as camera, GPS, and local device storage.  Native apps may offer greater flexibility in integrating with device native services.  However, since hybrid applications already provide device integrations that typical enterprise applications need, this is typically less of an issue.  The new Oracle ADF Mobile release is an HTML5 and Java hybrid framework that targets mobile app development to iOS and Android from one code base. So, Which is the Best Approach? The short answer is – the best choice depends on the type of application you are developing.  For instance, animation-intensive apps such as games would favor native apps, while hybrid applications may be better suited for enterprise mobile apps because they provide multi-platform support. Just for starters, the following issues must be considered when choosing a development path. Application Complexity: How complex is the application? A quick app that accesses a database or Web service for some data to display?  You can keep it simple, and a mobile Web app may suffice. However, for a mobile/field worker type of applications that supports mission critical functionality, hybrid or native applications are typically needed. Richness of User Interactivity: What type of user experience is required for the application?  Mobile browser-based app that’s optimized for mobile UI may suffice for quick lookup or productivity type of applications.  However, hybrid/native application would typically be required to deliver highly interactive user experiences needed for field-worker type of applications.  For example, interactive BI charts/graphs, maps, voice/email integration, etc.  In the most extreme case like gaming applications, native applications may be necessary to deliver the highly animated and graphically intensive user experience. Performance: What type of performance is required by the application functionality?  For instance, for real-time look up of data over the network, mobile app performance depends on network latency and server infrastructure capabilities.  If consistent performance is required, data would typically need to be cached, which is supported on hybrid or native applications only. Connectivity and Availability: What sort of connectivity will your application require? Does the app require Web access all the time in order to always retrieve the latest data from the server? Or do the requirements dictate offline support? While native and hybrid apps can be built to operate offline, Web mobile apps require Web connectivity. Multi-platform Requirements: The terms “consumerization of IT” and BYOD (bring your own device) effectively mean that the line between the consumer and the enterprise devices have become blurred. Employees are bringing their personal mobile devices to work and are often expecting that they work in the corporate network and access back-office applications.  Even if companies restrict access to the big dogs: (iPad, iPhone, Android phones and tablets, possibly Windows Phone and tablets), trying to support each platform natively will require increasing resources and domain expertise with each new language/platform. And let’s not forget the maintenance costs, involved in upgrading new versions of each platform.   Where multi-platform support is needed, Web mobile or hybrid apps probably have the advantage. Going native, and trying to support multiple operating systems may be cost prohibitive with existing resources and developer skills. Device-Services Access:  If your app needs to access local device services, such as the camera, contacts app, accelerometer, etc., then your choices are limited to native or hybrid applications.   Fragmentation: Apple controls Apple iOS and the only concern is what version iOS is running on any given device.   Not so Android, which is open source. There are many, many versions and variants of Android running on different devices, which can be a nightmare for app developers trying to support different devices running different flavors of Android.  (Is it an Amazon Kindle Fire? a Samsung Galaxy?  A Barnes & Noble Nook?) This is a nightmare scenario for native apps—on the other hand, a mobile Web or hybrid app, when properly designed, can shield you from these complexities because they are based on common frameworks.  Resources: How many developers can you dedicate to building and supporting mobile application development?  What are their existing skills sets?  If you’re considering native application development due to the complexity of the application under development, factor the costs of becoming proficient on a each platform’s OS and programming language. Add another platform, and that’s another language, another SDK. On the other side of the equation, Web mobile or hybrid applications are simpler to make, and readily support more platforms, but there may be performance trade-offs. Conclusion This only scratches the surface. However, I hope to have suggested some food for thought in choosing your mobile development strategy.  Do your due diligence, search the Web, read up on mobile, talk to peers, attend events. The development team at Oracle is working hard on mobile technologies to help customers extend enterprise applications to mobile faster and effectively.  To learn more on what Oracle has to offer, check out the Oracle ADF Mobile (hybrid) and ADF Faces/ADF Mobile browser (Web Mobile) solutions from Oracle.   Additional Information Blog: ADF Blog Product Information on OTN: ADF Mobile Product Information on Oracle.com: Oracle Fusion Middleware Follow us on Twitter and Facebook Subscribe to our regular Fusion Middleware Newsletter

    Read the article

  • Windows 7 sometimes boots in VGA mode

    - by TuxRug
    I have an Asus G50VT-x5 laptop with nVidia GeForce9800M-GS graphics. Normally, Windows boots normally, but about 20% of the time (rough estimate), it will boot with the fallback VGA driver, maxing out at 800x600 with no Aero. I've checked the system logs and there is nothing indicating an error loading the nVidia driver. It even specifies in the logs that the Nvidia Display Driver service started successfully, even though it has booted in safe graphics mode. This has been happening for a while, but it's happening a little more often now than it was before. Since the first time my system exhibited this behavior, I have updated my graphics driver a handful of times. I used System Information for Windows to check for problems there, but the only thing that stood out was the following: Core Temperature 4486449 °C (8075639 °F) Shaders Temperature 1171513530 °C (2108724330 °F) I know this reading is incorrect, because my laptop is nowhere near the surface of the sun and my desk has not burst into flames. When it's opererating normally, I get a sane reading like [Core Temperature 58 °C (136 °F)] with no Shaders Temperature listed. All I have to do to resolve the issue is reboot. I have seen no stability issues with the graphics or anything else. A long time ago, I had an issue with this computer where my framerate would suddenly drop during a 3D game from 40fps to <1fps, but after looking at the temperature readout immediately after quitting a game, I removed the bottom panel and blew the dust out of the vent and heatsink. Since then I have no drops in framerate under any situation. I have uploaded a zip containing the SIW reports for when the problem is occurring and when the computer is operating normally. I don't have a paid account so it can only be downloaded 10 times, so please only download the reports if you think you can use them. If you try to download the reports and they are no longer available, please comment and I will re-upload them. If you want to look at the files, they are on Rapidshare. EDIT It happened again, and I looked a little deeper into the System logs. When this happens, there are a lot of errors about other device drivers unable to start. All of these errors are for PnP drivers. Also, my USB keyboard and mouse take a few moments before they actually start working, although this happens sometimes the first normal boot as well. I am quite sure this is related, so I am adding the pnp tag. Also, CHKDSK will not run on boot. Even if a check is scheduled or a volume is manually set as dirty, CHKDSK will be skipped entirely, not even leaving an entry in the System logs. I tried running CHKNTFS /D, which did not work. I then manually changed my HKLM\System\CurrentControlSet\Control\Session Manager BootExecute value to the default listed on Microsoft's website. That did not work either. I ended up booting to repair mode and running CHKDSK there, which found a number of minor inconsistencies on my system drive, but none on my data drive. I have no idea if this is related. Some more information for those who don't download my SIW report file: Antivirus and Firewall are ESET Smart Security I have three different virutalization programs installed: VMware Player, Windows Virtual PC, and VirtualBox. The network adapters for these show up in the log of failed device starts. EDIT 2 I tried running sfc /scannow, which reported that it found corrupted files that could not be fixed. The CBS log is extremely cryptic. I tried booting to my install disk, launching repair mode, and doing an offline sfc from there, which produced the same result.

    Read the article

  • Exception Handling And Other Contentious Political Topics

    - by Justin Jones
    So about three years ago, around the time of my last blog post, I promised a friend I would write this post. Keeping promises is a good thing, and this is my first step towards easing back into regular blogging. I fully expect him to return from Pennsylvania to buy me a beer over this. However, it’s been an… ahem… eventful three years or so, and blogging, unfortunately, got pushed to the back burner on my priority list, along with a few other career minded activities. Now that the personal drama of the past three years is more or less resolved, it’s time to put a few things back on the front burner. What I consider to be proper exception handling practices is relatively well known these days. There are plenty of blog posts out there already on this topic which more or less echo my opinions on this topic. I’ll try to include a few links at the bottom of the post. Several years ago I had an argument with a co-worker who posited that exceptions should be caught at every level and logged. This might seem like sanity on the surface, but the resulting error log looked something like this: Error: System.SomeException Followed by small stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace. Error: System.SomeException Followed by slightly bigger stack trace.   These were all the same exception. The problem with this approach is that the error log, if you run any kind of analytics on in, becomes skewed depending on how far up the stack trace your exception was thrown. To mitigate this problem, we came up with the concept of the “PreLoggedException”. Basically, we would log the exception at the very top level and subsequently throw the exception back up the stack encapsulated in this pre-logged type, which our logging system knew to ignore. Now the error log looked like this: Error: System.SomeException Followed by small stack trace. Much cleaner, right? Well, there’s still a problem. When your exception happens in production and you go about trying to figure out what happened, you’ve lost more or less all context for where and how this exception was thrown, because all you really know is what method it was thrown in, but really nothing about who was calling the method or why. What gives you this clue is the entire stack trace, which we’re losing here. I believe that was further mitigated by having the logging system pull a system stack trace and add it to the log entry, but what you’re actually getting is the stack for how you got to the logging code. You’re still losing context about the actual error. Not to mention you’re executing a whole slew of catch blocks which are sloooooooowwwww……… In other words, we started with a bad idea and kept band-aiding it until it didn’t suck quite so bad. When I argued for not catching exceptions at every level but rather catching them following a certain set of rules, my co-worker warned me “do yourself a favor, never express that view in any future interviews.” I suppose this is my ultimate dismissal of that advice, but I’m not too worried. My approach for exception handling follows three basic rules: Only catch an exception if 1. You can do something about it. 2. You can add useful information to it. 3. You’re at an application boundary. Here’s what that means: 1. Only catch an exception if you can do something about it. We’ll start with a trivial example of a login system that uses a file. Please, never actually do this in production code, it’s just concocted example. So if our code goes to open a file and the file isn’t there, we get a FileNotFound exception. If the calling code doesn’t know what to do with this, it should bubble up. However, if we know how to create the file from scratch we can create the file and continue on our merry way. When you run into situations like this though, What should really run through your head is “How can I avoid handling an exception at all?” In this case, it’s a trivial matter to simply check for the existence of the file before trying to open it. If we detect that the file isn’t there, we can accomplish the same thing without having to handle in in a catch block. 2. Only catch an exception if you can do something about it. Continuing with the poorly thought out file based login system we contrived in part 1, if the code calls a Login(…) method and the FileNotFound exception is thrown higher up the stack, the code that calls Login must account for a FileNotFound exception. This is kind of counterintuitive because the calling code should not need to know the internals of the Login method, and the data file is an implementation detail. What makes more sense, assuming that we didn’t implement any of the good advice from step 1, is for Login to catch the FileNotFound exception and wrap it in a new exception. For argument’s sake we’ll say LoginSystemFailureException. (Sorry, couldn’t think of anything better at the moment.) This gives us two stack traces, preserving the original stack trace in the inner exception, and also is much more informative to the calling code. 3. Only catch an exception if you’re at an application boundary. At some point we have to catch all the exceptions, even the ones we don’t know what to do with. WinForms, ASP.Net, and most other UI technologies have some kind of built in mechanism for catching unhandled exceptions without fatally terminating the application. It’s still a good idea to somehow gracefully exit the application in this case if possible though, because you can no longer be sure what state your application is in, but nothing annoys a user more than an application just exploding. These unhandled exceptions need to be logged, and this is a good place to catch them. Ideally you never want this option to be exercised, but code as though it will be. When you log these exceptions, give them a “Fatal” status (e.g. Log4Net) and make sure these bugs get handled in your next release. That’s it in a nutshell. If you do it right each exception will only get logged once and with the largest stack trace possible which will make those 2am emergency severity 1 debugging sessions much shorter and less frustrating. Here’s a few people who also have interesting things to say on this topic:  http://blogs.msdn.com/b/ericlippert/archive/2008/09/10/vexing-exceptions.aspx http://www.codeproject.com/Articles/9538/Exception-Handling-Best-Practices-in-NET I know there’s more but I can’t find them at the moment.

    Read the article

  • Per-pixel displacement mapping GLSL

    - by Chris
    Im trying to implement a per-pixel displacement shader in GLSL. I read through several papers and "tutorials" I found and ended up with trying to implement the approach NVIDIA used in their Cascade Demo (http://www.slideshare.net/icastano/cascades-demo-secrets) starting at Slide 82. At the moment I am completly stuck with following problem: When I am far away the displacement seems to work. But as more I move closer to my surface, the texture gets bent in x-axis and somehow it looks like there is a little bent in general in one direction. EDIT: I added a video: click I added some screen to illustrate the problem: Well I tried lots of things already and I am starting to get a bit frustrated as my ideas run out. I added my full VS and FS code: VS: #version 400 layout(location = 0) in vec3 IN_VS_Position; layout(location = 1) in vec3 IN_VS_Normal; layout(location = 2) in vec2 IN_VS_Texcoord; layout(location = 3) in vec3 IN_VS_Tangent; layout(location = 4) in vec3 IN_VS_BiTangent; uniform vec3 uLightPos; uniform vec3 uCameraDirection; uniform mat4 uViewProjection; uniform mat4 uModel; uniform mat4 uView; uniform mat3 uNormalMatrix; out vec2 IN_FS_Texcoord; out vec3 IN_FS_CameraDir_Tangent; out vec3 IN_FS_LightDir_Tangent; void main( void ) { IN_FS_Texcoord = IN_VS_Texcoord; vec4 posObject = uModel * vec4(IN_VS_Position, 1.0); vec3 normalObject = (uModel * vec4(IN_VS_Normal, 0.0)).xyz; vec3 tangentObject = (uModel * vec4(IN_VS_Tangent, 0.0)).xyz; //vec3 binormalObject = (uModel * vec4(IN_VS_BiTangent, 0.0)).xyz; vec3 binormalObject = normalize(cross(tangentObject, normalObject)); // uCameraDirection is the camera position, just bad named vec3 fvViewDirection = normalize( uCameraDirection - posObject.xyz); vec3 fvLightDirection = normalize( uLightPos.xyz - posObject.xyz ); IN_FS_CameraDir_Tangent.x = dot( tangentObject, fvViewDirection ); IN_FS_CameraDir_Tangent.y = dot( binormalObject, fvViewDirection ); IN_FS_CameraDir_Tangent.z = dot( normalObject, fvViewDirection ); IN_FS_LightDir_Tangent.x = dot( tangentObject, fvLightDirection ); IN_FS_LightDir_Tangent.y = dot( binormalObject, fvLightDirection ); IN_FS_LightDir_Tangent.z = dot( normalObject, fvLightDirection ); gl_Position = (uViewProjection*uModel) * vec4(IN_VS_Position, 1.0); } The VS just builds the TBN matrix, from incoming normal, tangent and binormal in world space. Calculates the light and eye direction in worldspace. And finally transforms the light and eye direction into tangent space. FS: #version 400 // uniforms uniform Light { vec4 fvDiffuse; vec4 fvAmbient; vec4 fvSpecular; }; uniform Material { vec4 diffuse; vec4 ambient; vec4 specular; vec4 emissive; float fSpecularPower; float shininessStrength; }; uniform sampler2D colorSampler; uniform sampler2D normalMapSampler; uniform sampler2D heightMapSampler; in vec2 IN_FS_Texcoord; in vec3 IN_FS_CameraDir_Tangent; in vec3 IN_FS_LightDir_Tangent; out vec4 color; vec2 TraceRay(in float height, in vec2 coords, in vec3 dir, in float mipmap){ vec2 NewCoords = coords; vec2 dUV = - dir.xy * height * 0.08; float SearchHeight = 1.0; float prev_hits = 0.0; float hit_h = 0.0; for(int i=0;i<10;i++){ SearchHeight -= 0.1; NewCoords += dUV; float CurrentHeight = textureLod(heightMapSampler,NewCoords.xy, mipmap).r; float first_hit = clamp((CurrentHeight - SearchHeight - prev_hits) * 499999.0,0.0,1.0); hit_h += first_hit * SearchHeight; prev_hits += first_hit; } NewCoords = coords + dUV * (1.0-hit_h) * 10.0f - dUV; vec2 Temp = NewCoords; SearchHeight = hit_h+0.1; float Start = SearchHeight; dUV *= 0.2; prev_hits = 0.0; hit_h = 0.0; for(int i=0;i<5;i++){ SearchHeight -= 0.02; NewCoords += dUV; float CurrentHeight = textureLod(heightMapSampler,NewCoords.xy, mipmap).r; float first_hit = clamp((CurrentHeight - SearchHeight - prev_hits) * 499999.0,0.0,1.0); hit_h += first_hit * SearchHeight; prev_hits += first_hit; } NewCoords = Temp + dUV * (Start - hit_h) * 50.0f; return NewCoords; } void main( void ) { vec3 fvLightDirection = normalize( IN_FS_LightDir_Tangent ); vec3 fvViewDirection = normalize( IN_FS_CameraDir_Tangent ); float mipmap = 0; vec2 NewCoord = TraceRay(0.1,IN_FS_Texcoord,fvViewDirection,mipmap); //vec2 ddx = dFdx(NewCoord); //vec2 ddy = dFdy(NewCoord); vec3 BumpMapNormal = textureLod(normalMapSampler, NewCoord.xy, mipmap).xyz; BumpMapNormal = normalize(2.0 * BumpMapNormal - vec3(1.0, 1.0, 1.0)); vec3 fvNormal = BumpMapNormal; float fNDotL = dot( fvNormal, fvLightDirection ); vec3 fvReflection = normalize( ( ( 2.0 * fvNormal ) * fNDotL ) - fvLightDirection ); float fRDotV = max( 0.0, dot( fvReflection, fvViewDirection ) ); vec4 fvBaseColor = textureLod( colorSampler, NewCoord.xy,mipmap); vec4 fvTotalAmbient = fvAmbient * fvBaseColor; vec4 fvTotalDiffuse = fvDiffuse * fNDotL * fvBaseColor; vec4 fvTotalSpecular = fvSpecular * ( pow( fRDotV, fSpecularPower ) ); color = ( fvTotalAmbient + (fvTotalDiffuse + fvTotalSpecular) ); } The FS implements the displacement technique in TraceRay method, while always using mipmap level 0. Most of the code is from NVIDIA sample and another paper I found on the web, so I guess there cannot be much wrong in here. At the end it uses the modified UV coords for getting the displaced normal from the normal map and the color from the color map. I looking forward for some ideas. Thanks in advance! Edit: Here is the code loading the heightmap: glTexImage2D(GL_TEXTURE_2D, 0, GL_RGBA, mWidth, mHeight, 0, GL_RGBA, GL_UNSIGNED_BYTE, mImageData); glGenerateMipmap(GL_TEXTURE_2D); //glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_LINEAR_MIPMAP_LINEAR); //glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_LINEAR_MIPMAP_LINEAR); //glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_WRAP_S, GL_REPEAT); //glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_WRAP_T, GL_REPEAT); Maybe something wrong in here?

    Read the article

  • Delivering the Integrated Portal Experience!

    - by Michael Snow
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Guest post by Richard Maldonado, Principal Product Manager, Oracle WebCenter Portal Organizations are still struggling to standardize on a user interaction platform which can meet the needs of all their target audiences.  This has not only resulted in inefficient and inconsistent experiences for their users, but it also creates inefficiencies (productivity and costs) for the departments that manage the applications and information systems.  Portals have historically been the unifying platform that provide IT with a common interface which can securely surface the most relevant interactions for a given user and/or group of users.  However, organizations have found that the technologies available have either not provided the flexibility necessary to address all of their use cases, or they rely too much on IT resources to manage, maintain, and evolve.  Empowering  the Business Groups The core issue that IT departments face with delivering portal experiences is having enough resources to respond and address the influx of requirements which come in from the business.  Commonly, when a business group wants a new portal site established for their group, they will submit a request to the IT dept, the IT dept then assigns a resource to an administrator and/or developer to build.  Unfortunately, this approach is not scalable, it can be a time consuming activity which requires significant interaction between the business owner and the IT resource.  A modern user interaction platforms should empower the business groups by providing them tools which they can use to build and manage the portal experiences without the need for IT's involvement.  And because business groups rarely have technical resources (developers) on staff, the tools must be easy enough that virtually any business user could use.  In addition, the tool must be powerful enough to allow them to build the experience that they need, things such as creating a whole new portal, add/manage page and page hierarchy, manage user/group access, add/modify components within the page, etc.  This balance between ease-of-use and flexibility is key to the successful adoption of tools which will ultimately reduce the burden on IT, respond to the needs of the business, and deliver high-value experiences for the users.  Ready or Not, Here They Come: Smartphones and Tablets Recently, several studies have highlighted that smartphone and tablet-style devices have overtaken PC's in both sales and usage.  This shift is further driving organizations to revaluate how they're delivering data, information, and applications to their users.  Users are expecting to get the same level of access and interaction, but in a ways which are optimized for the capabilities of the device that they are using.  Expect More With the ever growing number of new IT projects and flat/shrinking budgets, organizations are looking for comprehensive solutions which can deliver integrated web experiences that are tailored for the users and optimized for mobile devices.  Piecing together a number of point solutions is no longer an option.  A modern portal technology should not only address the traditional needs of integrating and surfacing back-end applications/information, but it should enable the business through easy-to-use tools and accelerate the delivery of mobile optimized experiences.   v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} 12.00 Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} 12.00 Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} WebCenter in Action Series: Qualcomm Provides a Seamless Experience for Customers with Oracle WebCenter Featuring Qualcomm & Keste 12.00 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 -"/ /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:Calibri; mso-fareast-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} 12.00 Normal 0 false false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-fareast- mso-bidi-font-family:"Times New Roman";}

    Read the article

  • CodePlex Daily Summary for Monday, September 03, 2012

    CodePlex Daily Summary for Monday, September 03, 2012Popular ReleasesMetodología General Ajustada - MGA: 03.01.03: Cambios Aury: Ajuste del margen del reporte. Visualización de la columna de Supuestos en la parte del módulo de Decisión. Cambios John: Integración de código con cambios enviados por Aury Niño. Generación de instaladores. Soporte técnico por correo electrónico y telefónico.Iveely Search Engine: Iveely Search Engine (0.2.0): ????ISE?0.1.0??,?????,ISE?0.2.0?????????,???????,????????20???follow?ISE,????,??ISE??????????,??????????,?????????,?????????0.2.0??????,??????????。 Iveely Search Engine ?0.2.0?????????“??????????”,??????,?????????,???????,???????????????????,????、????????????。???0.1.0????????????: 1. ??“????” ??。??????????,?????????,???????????????????。??:????????,????????????,??????????????????。??????。 2. ??“????”??。?0.1.0??????,???????,???????????????,?????????????,????????,?0.2.0?,???????...Thisismyusername's codeplex page.: HTML5 Mulititouch Fruit Ninja Proof of Concept: This is an example of how you could create a game such as Fruit Ninja using HTML5's multitouch capabilities. Sorry this example doesn't have great graphics. If I had my own webpage, I could store some graphics and upload the game there and it might look halfway decent, but since I'm only using a Codeplex page and most mobile devices can't open .zip files, the fruits are just circles. I hope you enjoy reading the source code anyway.GmailDefaultMaker: GmailDefaultMaker 3.0.0.2: Add QQ Mail BugfixSmart Data Access layer: Smart Data access Layer Ver 3: In this version support executing inline query is added. Check Documentation section for detail.TSQL Code Smells Finder: POC 1.01: Proof of concept 1.01 TSQLDomTest.ps1 and Errors.Txt are requiredConfuser: Confuser build 76542: This is a build of changeset 76542.Reactive State Machine: ReactiveStateMachine-beta: TouchStateMachine now supports Microsoft Surface 2.0 SDK. The TouchStateMachine is an extension to the Reactive State Machine. Reactive State Machine uses NuGet for dependency managementSharePoint Column & View Permission: SharePoint Column and View Permission v1.2: Version 1.2 of this project. If you will find any bugs please let me know at enti@zoznam.sk or post your findings in Issue TrackerMihmojsos OS: Mihmojsos OS 3 (Smart Rabbit): !Mihmojsos OS 3 Smart Rabbit Mihmojsos Smart Rabbit is now availableDotNetNuke Translator: 01.00.00 Beta: First release of the project.YNA: YNA 0.2 alpha: Wath's new since 0.1 alpha ? A lot of changes but there are the most interresting : StateManager is now better and faster Mouse events for all YnObjects (Sprites, Images, texts) A really big improvement for YnGroup Gamepad support And the news : Tiled Map support (need refactoring) Isometric tiled map support (need refactoring) Transition effect like "FadeIn" and "FadeOut" (YnTransition) Timers (YnTimer) Path management (YnPath, need more refactoring) Downloads All downloads...Audio Pitch & Shift: Audio Pitch And Shift 5.1.0.2: fixed several issues with streaming modeUrlPager: UrlPager 1.2: Fixed bug in which url parameters will lost after paging; ????????url???bug;Sofire Suite: Sofire v1.5.0.0: Sofire v1.5.0.0 ?? ???????? ?????: 1、?? 2、????EntLib.com????????: EntLib.com???????? v3.0: EntLib eCommerce Solution ???Microsoft .Net Framework?????????????????????。Coevery - Free CRM: Coevery 1.0.0.24: Add a sample database, and installation instructions.Math.NET Numerics: Math.NET Numerics v2.2.1: Major linear algebra rework since v2.1, now available on Codeplex as well (previous versions were only available via NuGet). Since v2.2.0: Student-T density more robust for very large degrees of freedom Sparse Kronecker product much more efficient (now leverages sparsity) Direct access to raw matrix storage implementations for advanced extensibility Now also separate package for signed core library with a strong name (we dropped strong names in v2.2.0) Also available as NuGet packages...Microsoft SQL Server Product Samples: Database: AdventureWorks Databases – 2012, 2008R2 and 2008: About this release This release consolidates AdventureWorks databases for SQL Server 2012, 2008R2 and 2008 versions to one page. Each zip file contains an mdf database file and ldf log file. This should make it easier to find and download AdventureWorks databases since all OLTP versions are on one page. There are no database schema changes. For each release of the product, there is a light-weight and full version of the AdventureWorks sample database. The light-weight version is denoted by ...Christoc's DotNetNuke Module Development Template: DotNetNuke Project Templates V1.1 for VS2012: This release is specifically for Visual Studio 2012 Support, distributed through the Visual Studio Extensions gallery at http://visualstudiogallery.msdn.microsoft.com/ After you build in Release mode the installable packages (source/install) can be found in the INSTALL folder now, within your module's folder, not the packages folder anymore Check out the blog post for all of the details about this release. http://www.dotnetnuke.com/Resources/Blogs/EntryId/3471/New-Visual-Studio-2012-Projec...New ProjectsBPVote4PPT: BPVote For PowerPointCosmo OS: La semplicità in un OSFinancial Analytic Tools: C#.Net Financial Analytic ToolsGeminiMVC: An Open Source CMS written in ASP.net MVC 4 with speed, extensibility, and ease-of-us in mind.JQuery SharePoint Autocomplete People Picker: This JQUery bundle provides an autocomplete people picker based on SharePoint profiles. It can be hosted on the SharePoint itself or on remote applications.Kerbal Space Program PartModule Library: This project is designed to add various functionalities to custom parts for the space program simulation game Kerbal Space Program.KeyboardRemapper: This tool to remaps keys in the keyboard. If you have more than one keyboard or an additional keypad, you can remap the keys of the each keyboard independentlyKHStudent: ??????Localized DataAnnotations with T4 templates: Simplified DataAnnotations localization using T4 templates.MfcLightToolkit: Supports development for small and simple MFC application. Provides asynchronous programming model like .NET, file download, easy control resizing, and so on.Müslüm ÖZTÜRK Code Lib: Test amaçli olusturulan projemdirPolska: Testproject in how a polish grammerprogram can look like.QueueLessApp: Here is the codeRusIS.CMS: aaaSGPS: Projeto de controle de produtos e serviçosStemmersNet: Stemmers pack for .Net FrameworkTrabajo Final de Ingenieria - Javier Vallejos: Tesis Final de la carrera de Ingenieria - Universidad Abierta Interamericana.TSQL Code Smells Finder: TSQL 'smells' findersXNA and Data Driven Design: This project includes links for XNA and Data Driven DesignXNA and System Testing: This project includes code for XNA and System TestingYUGI-AR Project: an open source project for yugioh based augmented reality???????? ? ?????????????: ???? ??????? ??????? ?????????????? ??????????? ?????????? ??? ? ????? ?????? ? ? ??? ??? ????? ? ??? ?????????? ????????????.

    Read the article

  • laptop crashed: why?

    - by sds
    my linux (ubuntu 12.04) laptop crashed, and I am trying to figure out why. # last sds pts/4 :0 Tue Sep 4 10:01 still logged in sds pts/3 :0 Tue Sep 4 10:00 still logged in reboot system boot 3.2.0-29-generic Tue Sep 4 09:43 - 11:23 (01:40) sds pts/8 :0 Mon Sep 3 14:23 - crash (19:19) this seems to indicate a crash at 09:42 (= 14:23+19:19). as per another question, I looked at /var/log: auth.log: Sep 4 09:17:02 t520sds CRON[32744]: pam_unix(cron:session): session closed for user root Sep 4 09:43:17 t520sds lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) no messages file syslog: Sep 4 09:24:19 t520sds kernel: [219104.819975] CPU0: Package power limit normal Sep 4 09:43:16 t520sds kernel: imklog 5.8.6, log source = /proc/kmsg started. kern.log: Sep 4 09:24:19 t520sds kernel: [219104.819969] CPU1: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819971] CPU2: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819974] CPU3: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819975] CPU0: Package power limit normal Sep 4 09:43:16 t520sds kernel: imklog 5.8.6, log source = /proc/kmsg started. Sep 4 09:43:16 t520sds kernel: [ 0.000000] Initializing cgroup subsys cpuset Sep 4 09:43:16 t520sds kernel: [ 0.000000] Initializing cgroup subsys cpu I had a computation running until 9:24, but the system crashed 18 minutes later! kern.log has many pages of these: Sep 4 09:43:16 t520sds kernel: [ 0.000000] total RAM covered: 8086M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 64K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 128K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 256K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 512K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 1M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 4M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 8M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 16M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 32M num_reg: 10 lose cover RAM: -16M Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 64M num_reg: 10 lose cover RAM: -16M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 128M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 256M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 512M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 1G num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 2G num_reg: 10 lose cover RAM: -1G does this mean that my RAM is bad?! it also says Sep 4 09:43:16 t520sds kernel: [ 2.944123] EXT4-fs (sda1): INFO: recovery required on readonly filesystem Sep 4 09:43:16 t520sds kernel: [ 2.944126] EXT4-fs (sda1): write access will be enabled during recovery Sep 4 09:43:16 t520sds kernel: [ 3.088001] firewire_core: created device fw0: GUID f0def1ff8fbd7dff, S400 Sep 4 09:43:16 t520sds kernel: [ 8.929243] EXT4-fs (sda1): orphan cleanup on readonly fs Sep 4 09:43:16 t520sds kernel: [ 8.929249] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 658984 ... Sep 4 09:43:16 t520sds kernel: [ 9.343266] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 525343 Sep 4 09:43:16 t520sds kernel: [ 9.343270] EXT4-fs (sda1): 56 orphan inodes deleted Sep 4 09:43:16 t520sds kernel: [ 9.343271] EXT4-fs (sda1): recovery complete Sep 4 09:43:16 t520sds kernel: [ 9.645799] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) does this mean my HD is bad? As per FaultyHardware, I tried smartctl -l selftest, which uncovered no errors: smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-30-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9500420AS Serial Number: 5VJE81YK LU WWN Device Id: 5 000c50 0440defe3 Firmware Version: 0003LVM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Mon Sep 10 16:40:04 2012 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 109) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 034 Pre-fail Always - 162843537 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 571 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 17210154023 9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 174362787320258 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 571 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 1 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 061 043 045 Old_age Always In_the_past 39 (0 11 44 26) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 84 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 20 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2434 194 Temperature_Celsius 0x0022 039 057 000 Old_age Always - 39 (0 15 0 0) 195 Hardware_ECC_Recovered 0x001a 041 041 000 Old_age Always - 162843537 196 Reallocated_Event_Count 0x000f 095 095 030 Pre-fail Always - 4540 (61955, 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4545 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Googling for the messages proved inconclusive, I can't even figure out whether the messages are routine or catastrophic. So, what do I do now?

    Read the article

  • Installation of Access Database Engine 32-bit Fails

    - by Rayzor78
    I am trying to install Access Database Engine 2007 32-bit. The splash screen comes up, you click "Next", then it fails with the error: Installation ended prematurely because of an error You click "OK" and another error window says: The installation of the package failed. The exact same situation happens when I try this with Access Database Engine 2010 32-bit. This production server is running Windows Server 2008 R2 SP1 64-bit. Before I tried installing Access Database Engine 32-bit, I first needed to install Microsoft Office 2010 Pro (Excel and Office Tools only). I tried the 32-bit version on the production server since that is how I set it up in our Dev environment. No luck. The 32-bit version would not install. I did NOT get the error "You have 64-bit components of Office installed". I simply received the exact same two errors listed above. So, I knew that 32-bit/64-bit did not really matter for the Office install for my project, so I installed 64-bit of Office Pro 2010 (Excel and Office Tools only) with no problems. I have a requirement that I need to have the 32-bit version of the Access Database Engine installed. 2007 or 2010, doesn't matter. I cannot use the 64-bit version of Access Database Engine 2010 because my SSIS package will not work with it. I require the 32-bit version. I've tried several steps to try to get it installed. I seriously think that the production server has some aversion to installing 32-bit applications. Here's what I've tried: Tried installing via command line with the "/passive" switch....no luck. Tried numerous iterations to copy the install file to the server (downloaded a fresh copy directly to the server, downloaded a fresh copy to my local machine then copied it over, copied it over zipped up) (http://social.msdn.microsoft.com/Forums/en-US/sqldataaccess/thread/efd3c1f0-07cd-45ca-a626-2dd0c7ac3e9f). Tried Method 1 from this link. Could not try Method 2 because it requires a server reboot and in my environment that requires a long change management process. I've verified that I am a local administrator on the server. (Evidence, I am able to install other applications (office 64-bit per above)). Verified that there are no other office products that should be blocking the installation. The fore-mentioned install of Excel 2010 64-bit was the first Office product installed on the server. VERY ODD: To test my theory that the production server does not like 32-bit applications, I installed something lightweight. I installed 7-Zip 32-bit on the production server with no problems whatsoever. Here are some things that I have not tried (i will follow-up once I do): Method 2 (as mentioned above). Requires a server reboot. Have not verified that the Dev and Production environments are 100% identical. I've done a cursory check and on the surface they appear to be the same (same OS and SP version). I need to do a deeper dive to be 100% certain. I had no problems in my Dev environment. In Dev, I installed Office 2010 Pro 64-bit (Excel & Office Tools only) then via command line w/ the "/passive" switch, installed Access Database Engine 2010 32-bit. I don't know what else to try. Any suggestions or comments?

    Read the article

  • Backup, Migrate or Clone Failing CentOS 4 (LVM)

    - by Hegelworm
    I've been running a BlueQuartz CentOS 4 system (Nuonce.net distro) for a few years now and although the hard drive (Deskstar) has always been a bit noisy, on a few recent occasions I've heard it having trouble spinning up. Basically, I want to clone this drive to a similar sized one (80 Gig). I've spent many hours reading upon dd, dd_rescue, rsync, clonezilla and LVM mirroring yet the sheer number of options and nightmarish accounts has left me frozen - unable to make an informed decision as to how to start. I've made a few attempts. dd failed after about 2 hours, as, although the drives appeared to be identical on the surface (ATA Seagate Barracudas, Thai not Chinese), the destination drive is slightly smaller. My most recent attempt involved using a Debian CD to format the new drive and then rsync-ing everything over and editing the new drive's grub and fstab to reflect the changes. No joy here either as I hadn't chosen LVM when partitioning the destination drive and it wouldn't boot. As you can probably tell, I'm out of my depth here and a panic-invoking mixture of caution and frustration has prompted me to sign up here. The server itself, although not strictly a production environment, has a very specific installation of Festival, LAME and ffMpeg and provides the back-end for a Text-to-Speech jQuery plugin that I've built over the last 2 years. I'm also planning to rebuild the whole TTS system on Debian as the existing CentOS system still has PHP4 etc. For now though, I'd really like to just shift everything over to a new drive. As this is my first post, please feel free to lay any house rules on me that I might've overlooked; I've been hovering around StackOverflow for a while now but have only just signed up. Many thanks. Update: Thanks for your responses so far - it's much appreciated and makes me feel a little more confident when I can double-check things here. I had the idea of doing a fresh install of CentOS (from the original disk) on the new drive so the partitions and LVM were all set up correctly (after disconnecting my source drive to prevent painful mistakes). I then booted into rescue mode from the same CD, and, to avoid a conflicting label, changed the /boot partition's label using e2label to /bootnew. I then changed the VolGroup name using lvm vgrename from VolGroup00 to VolGroup001. I could then boot with both drives in. After mounting the new drive (via its VolGroup001 alias) into /newhd, I rsync-ed over everything I could to the new drive, using -avr switches and backslashes. Like mentioned here. I then disconnected my original source drive again, booted from the liveCD again, changed back the boot partition label from /bootnew to /boot using e2label and then renamed the VolGroup back to VolGroup00. I then rebooted and it went through the familiar start-up routine only to not find a host of files in proc, usr, lib, var etc. The boot did complete but there were lots of red 'FAILS'. I could log in with my existing creds, but the network was kaput, I couldn't startX (desktop GUI) and there were also a few (a lot) of error messages pertaining to iptables. Back to square one. I naively thought I'd nailed it. Shall I just buy a bigger hard drive and attempt the dd route? I've read that this can mess with LVM setups and there's the added risk of working on two unmounted drives at once with a low-level tool. Thanks again.

    Read the article

  • Confirm disk is broken when it passes all diagnostics

    - by Halfgaar
    I have a system with a potentially broken disk, but the disk passes all manner of diagnostics. I have been unable to confirm that the disk is broken. What are my options? I could just replace the disk, but because this situation is very similar to another more severe situation I have (long story), I'd like to actually make a proper diagnosis as opposed to randomly binning hardware. The issue and history is this: I had a Debian Linux PC (500 MHz P3) acting as router, nagios and munin. It crashed every couple of weeks. No logs or dmesg could be obtained (because it's an old Compaq that only boots when you configure it as keyboardless, making connecting a keyboard later, once it's booted, impossible). At the time, I just replaced the computer with another Compaq (P4 2.4 GHz) because I thought the hardware was faulty. However, it still crashed every couple of weeks. the difference is that on this computer, I can still SSH into it. It gives all kinds of errors on hda. I'd like to confirm that the disk is broken, but nothing I do confirms this: SMART error logs shows no errors. Normally when a disk starts acting up, SMART my pass, but it still records a read-error in the error log. SMART self-test (smartctl -t long /dev/sda) completes without errors. re-allocated sector count (a tell-tale parameter) has been 31 all its life, even when the disk was still in use in my desktop PC years ago, and it still is. The figure never changed. dd if=/dev/sda of=/dev/null bs=4096 passes with flying colors. What else can I do to assess the health of the drive? Again, this is not about making this router fully functional again, this is a disk forensic question, because it just so happens that I have another server that potentially has the same problem, and knowing the answer to this will possibly help me greatly. For the record, below are logs and such. This is the smartctl -a output: smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3120026A Serial Number: 5JT1CLQM Firmware Version: 3.06 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Mon Jul 1 21:18:33 2013 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 24) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 050 046 006 Pre-fail Always - 47766662 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 10 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 820305 9 Power_On_Hours 0x0032 048 048 000 Old_age Always - 46373 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 605 194 Temperature_Celsius 0x0022 036 065 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x001a 050 046 000 Old_age Always - 47766662 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 6 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 80% 46361 - # 2 Extended offline Completed without error 00% 46358 - # 3 Short offline Completed without error 00% 12046 - # 4 Extended offline Completed without error 00% 10472 - # 5 Short offline Completed without error 00% 10471 - # 6 Short offline Completed without error 00% 10471 - # 7 Short offline Completed without error 00% 6770 - # 8 Extended offline Aborted by host 90% 5958 - # 9 Extended offline Aborted by host 90% 5951 - #10 Short offline Completed without error 00% 5024 - #11 Extended offline Aborted by host 80% 5024 - #12 Short offline Completed without error 00% 3697 - #13 Short offline Completed without error 00% 237 - #14 Short offline Completed without error 00% 145 - #15 Short offline Completed without error 00% 69 - #16 Extended offline Completed without error 00% 68 - #17 Short offline Completed without error 00% 66 - #18 Short offline Completed without error 00% 49 - #19 Short offline Completed without error 00% 29 - #20 Short offline Completed without error 00% 29 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the dmesg error when it has crashed (which repeats for a bunch of different sectors): [1755091.211136] sd 0:0:0:0: [sda] Unhandled error code [1755091.211144] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1755091.211151] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 08 fe ad 38 00 00 08 00 [1755091.211166] end_request: I/O error, dev sda, sector 150908216

    Read the article

  • Skipping scheduled self-tests and predicting drive EOL

    - by Steve Madsen
    For a few weeks now, smartd has been reporting that it is skipping some of its scheduled self-tests on the weekends: Apr 24 18:29:32 calvin smartd[4758]: Device: /dev/sda, skip scheduled Offline Immediate Test; 40% remaining of current Self-Test. Apr 24 18:29:33 calvin smartd[4758]: Device: /dev/sdb, skip scheduled Offline Immediate Test; 50% remaining of current Self-Test. The drives in this RAID-1 array are set to run an offline test four times a day, a short self-test at 2am every day, and a long self-test on Saturdays at 2am. For some reason, it looks like the long self-test is taking longer, causing the other scheduled tests to be skipped. First question: is this a sign of likely drive failure? Then today, smartd reported that a self-test failed. Here is the output of smartctl -a /dev/sdb: smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 family Device Model: ST3250823AS Serial Number: 3ND1GNBC Firmware Version: 3.03 User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Apr 25 13:15:34 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 047 039 006 Pre-fail Always - 168450357 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 33 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 9 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 654745480 9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 40141 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 51 194 Temperature_Celsius 0x0022 037 062 000 Old_age Always - 37 (0 17 0 0) 195 Hardware_ECC_Recovered 0x001a 047 039 000 Old_age Always - 168450357 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 40131 - # 2 Extended offline Completed: read failure 30% 40129 379795511 # 3 Short offline Completed without error 00% 40084 - # 4 Short offline Completed without error 00% 40060 - # 5 Short offline Completed without error 00% 40036 - # 6 Short offline Completed without error 00% 40013 - # 7 Short offline Completed without error 00% 39990 - # 8 Extended offline Completed without error 00% 39977 - # 9 Short offline Completed without error 00% 39919 - #10 Short offline Completed without error 00% 39895 - #11 Short offline Completed without error 00% 39872 - #12 Short offline Completed without error 00% 39848 - #13 Short offline Completed without error 00% 39824 - #14 Short offline Completed without error 00% 39801 - #15 Extended offline Completed without error 00% 39789 - #16 Short offline Completed without error 00% 39754 - #17 Short offline Completed without error 00% 39732 - #18 Short offline Completed without error 00% 39707 - #19 Short offline Completed without error 00% 39683 - #20 Short offline Completed without error 00% 39660 - #21 Short offline Completed without error 00% 39636 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Given that this drive is about 4.5 years old, I am probably tempting fate by keeping it in service. SMART doesn't seem to get much respect as a reliable way to predict drive failure. What else can I use to get an early indication of drive failure?

    Read the article

  • The HTG Guide to Using a Bluetooth Keyboard with Your Android Device

    - by Matt Klein
    Android devices aren’t usually associated with physical keyboards. But, since Google is now bundling their QuickOffice app with the newly-released Kit-Kat, it appears inevitable that at least some Android tablets (particularly 10-inch models) will take on more productivity roles. In recent years, physical keyboards have been rendered obsolete by swipe style input methods such as Swype and Google Keyboard. Physical keyboards tend to make phones thick and plump, and that won’t fly today when thin (and even flexible and curved) is in vogue. So, you’ll be hard-pressed to find smartphone manufacturers launching new models with physical keyboards, thus rendering sliders to a past chapter in mobile phone evolution. It makes sense to ditch the clunky keyboard phone in favor of a lighter, thinner model. You’re going to carry around in your pocket or purse all day, why have that extra bulk and weight? That said, there is sound logic behind pairing tablets with keyboards. Microsoft continues to plod forward with its Surface models, and while critics continue to lavish praise on the iPad, its functionality is obviously enhanced and extended when you add a physical keyboard. Apple even has an entire page devoted specifically to iPad-compatible keyboards. But an Android tablet and a keyboard? Does such a thing even exist? They do actually. There are docking keyboards and keyboard/case combinations, there’s the Asus Transformer family, Logitech markets a Windows 8 keyboard that speaks “Android”, and these are just to name a few. So we know that keyboard products that are designed to work with Android exist, but what about an everyday Bluetooth keyboard you might use with Windows or OS X? How-To Geek wanted look at how viable it is to use such a keyboard with Android. We conducted some research and examined some lists of Android keyboard shortcuts. Most of what we found was long outdated. Many of the shortcuts don’t even apply anymore, while others just didn’t work. Regardless, after a little experimentation and a dash of customization, it turns out using a keyboard with Android is kind of fun, and who knows, maybe it will catch on. Setting things up Setting up a Bluetooth keyboard with Android is very easy. First, you’ll need a Bluetooth keyboard and of course an Android device, preferably running version 4.1 (Jelly Bean) or higher. For our test, we paired a second-generation Google Nexus 7 running Android 4.3 with a Samsung Series 7 keyboard. In Android, enable Bluetooth if it isn’t already on. We’d like to note that if you don’t normally use Bluetooth accessories and peripherals with your Android device (or any device really), it’s best practice to leave Bluetooth off because, like GPS, it drains the device’s battery more quickly. To enable Bluetooth, simply go to “Settings” -> “Bluetooth” and tap the slider button to “On”. To set up the keyboard, make sure it is on and then tap “Bluetooth” in the Android settings. On the resulting screen, your Android device should automatically search for and hopefully find your keyboard. If you don’t get it right the first time, simply turn the keyboard on again and then tap “Search for Devices” to try again. If it still doesn’t work, make sure you have fresh batteries and the keyboard isn’t paired to another device. If it is, you will need to unpair it before it will work with your Android device (consult your keyboard manufacturer’s documentation or Google if you don’t know how to do this). When Android finds your keyboard, select it under “Available Devices” … … and you should be prompted to type in a code: If successful, you will see that device is now “Connected” and you’re ready to go. If you want to test things out, try pressing the “Windows” key (“Apple” or “Command”) + ESC, and you will be whisked to your Home screen. So, what can you do? Traditional Mac and Windows users know there’s usually a keyboard shortcut for just about everything (and if there isn’t, there’s all kinds of ways to remap keys to do a variety of commands, tasks, and functions). So where does Android fall in terms of baked-in keyboard commands? There answer to that is kind of enough, but not too much. There are definitely established combos you can use to get around, but they aren’t clear and there doesn’t appear to be any one authority on what they are. Still, there is enough keyboard functionality in Android to make it a viable option, if only for those times when you need to get something done (long e-mail or important document) and an on-screen keyboard simply won’t do. It’s important to remember that Android is, and likely always will be a touch-first interface. That said, it does make some concessions to physical keyboards. In other words, you can get around Android fairly well without having to lift your hands off the keys, but you will still have to tap the screen regularly, unless you add a mouse. For example, you can wake your device by tapping a key rather than pressing its power button. However, if your device is slide or pattern-locked, then you’ll have to use the touchscreen to unlock it – a password or PIN however, works seamlessly with a keyboard – other things like widgets and app controls and features, have to be tapped. You get the idea. Keyboard shortcuts and navigation As we said, baked-in keyboard shortcut combos aren’t necessarily abundant nor apparent. The one thing you can always do is search. Any time you want to Google something, start typing from the Home screen and the search screen will automatically open and begin displaying results. Other than that, here is what we were able to figure out: ESC = go back CTRL + ESC = menu CTRL + ALT + DEL = restart (no questions asked) ALT + SPACE = search page (say “OK Google” to voice search) ALT + TAB (ALT + SHIFT + TAB) = switch tasks Also, if you have designated volume function keys, those will probably work too. There’s also some dedicated app shortcuts like calculator, Gmail, and a few others: CMD + A = calculator CMD + C = contacts CMD + E = e-mail CMD + G = Gmail CMD + L = Calendar CMD + P = Play Music CMD + Y = YouTube Overall, it’s not a long comprehensive list and there’s no dedicated keyboard combos for the full array of Google’s products. Granted, it’s hard to imagine getting a lot of mileage out of a keyboard with Maps but with something like Keep, you could type out long, detailed lists on your tablet, and then view them on your smartphone when you go out shopping. You can also use the arrow keys to navigate your Home screen over shortcuts and open the app drawer. When something on the screen is selected, it will be highlighted in blue. Press “Enter” to open your selection. Additionally, if an app has its own set of shortcuts, e.g. Gmail has quite a few unique shortcuts to it, as does Chrome, some – though not many – will work in Android (not for YouTube though). Also, many “universal” shortcuts such as Copy (CTRL + C), Cut (CTRL + X), Paste (CTRL + V), and Select All (CTRL + A) work where needed – such as in instant messaging, e-mail, social media apps, etc. Creating custom application shortcuts What about custom shortcuts? When we were researching this article, we were under the impression that it was possible to assign keyboard combinations to specific apps, such as you could do on older Android versions such as Gingerbread. This no long seems to be the case and nowhere in “Settings” could we find a way to assign hotkey combos to any of our favorite, oft-used apps or functions. If you do want custom keyboard shortcuts, what can you do? Luckily, there’s an app on Google Play that allows you to, among other things, create custom app shortcuts. It is called External Keyboard Helper (EKH) and while there is a free demo version, the pay version is only a few bucks. We decided to give EKH a whirl and through a little experimentation and finally reading the developer’s how-to, we found we could map custom keyboard combos to just about anything. To do this, first open the application and you’ll see the main app screen. Don’t worry about choosing a custom layout or anything like that, you want to go straight to the “Advanced settings”: In the “Advanced settings” select “Application shortcuts” to continue: You can have up to 16 custom application shortcuts. We are going to create a custom shortcut to the Facebook app. We choose “A0”, and from the resulting list, Facebook. You can do this for any number of apps, services, and settings. As you can now see, the Facebook app has now been linked to application-zero (A0): Go back to the “Advanced settings” and choose “Customize keyboard mappings”: You will be prompted to create a custom keyboard layout so we choose “Custom 1”: When you choose to create a custom layout, you can do a great many more things with your keyboard. For example, many keyboards have predefined function (Fn) keys, which you can map to your tablet’s brightness controls, toggle WiFi on/off, and much more. A word of advice, the application automatically remaps certain keys when you create a custom layout. This might mess up some existing keyboard combos. If you simply want to add some functionality to your keyboard, you can go ahead and delete EKH’s default changes and start your custom layout from scratch. To create a new combo, select “Add new key mapping”: For our new shortcut, we are going to assign the Facebook app to open when we key in “ALT + F”. To do this, we press the “F” key while in the “Scancode” field and we see it returns a value of “33”. If we wanted to use a different key, we can press “Change” and scan another key’s numerical value. We now want to assign the “ALT” key to application “A0”, previously designated as the Facebook app. In the “AltGr” field, we enter “A0” and then “Save” our custom combo. And now we see our new application shortcut. Now, as long as we’re using our custom layout, every time we press “ALT + F”, the Facebook app will launch: External Keyboard Helper extends far beyond simple application shortcuts and if you are looking for deeper keyboard customization options, you should definitely check it out. Among other things, EKH also supports dozens of languages, allows you to quickly switch between layouts using a key or combo, add up to 16 custom text shortcuts, and much more! It can be had on Google Play for $2.53 for the full version, but you can try the demo version for free. More extensive documentation on how to use the app is also available. Android? Keyboard? Sure, why not? Unlike traditional desktop operating systems, you don’t need a physical keyboard and mouse to use a mobile operating system. You can buy an iPad or Nexus 10 or Galaxy Note, and never need another accessory or peripheral – they work as intended right out of the box. It’s even possible you can write the next great American novel on one these devices, though that might require a lot of practice and patience. That said, using a keyboard with Android is kind of fun. It’s not revelatory but it does elevate the experience. You don’t even need to add customizations (though they are nice) because there are enough existing keyboard shortcuts in Android to make it usable. Plus, when it comes to inputting text such as in an editor or terminal application, we fully advocate big, physical keyboards. Bottom line, if you’re looking for a way to enhance your Android tablet, give a keyboard a chance. Do you use your Android device for productivity? Is a physical keyboard an important part of your setup? Do you have any shortcuts that we missed? Sound off in the comments and let us know what you think.     

    Read the article

  • Time Warp

    - by Jesse
    It’s no secret that daylight savings time can wreak havoc on systems that rely heavily on dates. The system I work on is centered around recording dates and times, so naturally my co-workers and I have seen our fair share of date-related bugs. From time to time, however, we come across something that we haven’t seen before. A few weeks ago the following error message started showing up in our logs: “The supplied DateTime represents an invalid time. For example, when the clock is adjusted forward, any time in the period that is skipped is invalid.” This seemed very cryptic, especially since it was coming from areas of our application that are typically only concerned with capturing date-only (no explicit time component) from the user, like reports that take a “start date” and “end date” parameter. For these types of parameters we just leave off the time component when capturing the date values, so midnight is used as a “placeholder” time. How is midnight an “invalid time”? Globalization Is Hard Over the last couple of years our software has been rolled out to users in several countries outside of the United States, including Brazil. Brazil begins and ends daylight savings time at midnight on pre-determined days of the year. On October 16, 2011 at midnight many areas in Brazil began observing daylight savings time at which time their clocks were set forward one hour. This means that at the instant it became midnight on October 16, it actually became 1:00 AM, so any time between 12:00 AM and 12:59:59 AM never actually happened. Because we store all date values in the database in UTC, always adjust any “local” dates provided by a user to UTC before using them as filters in a query. The error we saw was thrown by .NET when trying to convert the Brazilian local time of 2011-10-16 12:00 AM to UTC since that local time never actually existed. We hadn’t experienced this same issue with any of our US customers because the daylight savings time changes in the US occur at 2:00 AM which doesn’t conflict with our “placeholder” time of midnight. Detecting Invalid Times In .NET you might use code similar to the following for converting a local time to UTC: var localDate = new DateTime(2011, 10, 16); //2011-10-16 @ midnight const string timeZoneId = "E. South America Standard Time"; //Windows system timezone Id for "Brasilia" timezone. var localTimeZone = TimeZoneInfo.FindSystemTimeZoneById(timeZoneId); var convertedDate = TimeZoneInfo.ConvertTimeToUtc(localDate, localTimeZone); The code above throws the “invalid time” exception referenced above. We could try to detect whether or not the local time is invalid with something like this: var localDate = new DateTime(2011, 10, 16); //2011-10-16 @ midnight const string timeZoneId = "E. South America Standard Time"; //Windows system timezone Id for "Brasilia" timezone. var localTimeZone = TimeZoneInfo.FindSystemTimeZoneById(timeZoneId); if (localTimeZone.IsInvalidTime(localDate)) localDate = localDate.AddHours(1); var convertedDate = TimeZoneInfo.ConvertTimeToUtc(localDate, localTimeZone); This code works in this particular scenario, but it hardly seems robust. It also does nothing to address the issue that can arise when dealing with the ambiguous times that fall around the end of daylight savings. When we roll the clocks back an hour they record the same hour on the same day twice in a row. To continue on with our Brazil example, on February 19, 2012 at 12:00 AM, it will immediately become February 18, 2012 at 11:00 PM all over again. In this scenario, how should we interpret February 18, 2011 11:30 PM? Enter Noda Time I heard about Noda Time, the .NET port of the Java library Joda Time, a little while back and filed it away in the back of my mind under the “sounds-like-it-might-be-useful-someday” category.  Let’s see how we might deal with the issue of invalid and ambiguous local times using Noda Time (note that as of this writing the samples below will only work using the latest code available from the Noda Time repo on Google Code. The NuGet package version 0.1.0 published 2011-08-19 will incorrectly report unambiguous times as being ambiguous) : var localDateTime = new LocalDateTime(2011, 10, 16, 0, 0); const string timeZoneId = "Brazil/East"; var timezone = DateTimeZone.ForId(timeZoneId); var localDateTimeMaping = timezone.MapLocalDateTime(localDateTime); ZonedDateTime unambiguousLocalDateTime; switch (localDateTimeMaping.Type) { case ZoneLocalMapping.ResultType.Unambiguous: unambiguousLocalDateTime = localDateTimeMaping.UnambiguousMapping; break; case ZoneLocalMapping.ResultType.Ambiguous: unambiguousLocalDateTime = localDateTimeMaping.EarlierMapping; break; case ZoneLocalMapping.ResultType.Skipped: unambiguousLocalDateTime = new ZonedDateTime( localDateTimeMaping.ZoneIntervalAfterTransition.Start, timezone); break; default: throw new InvalidOperationException(string.Format("Unexpected mapping result type: {0}", localDateTimeMaping.Type)); } var convertedDateTime = unambiguousLocalDateTime.ToInstant().ToDateTimeUtc(); Let’s break this sample down: I’m using the Noda Time ‘LocalDateTime’ object to represent the local date and time. I’ve provided the year, month, day, hour, and minute (zeros for the hour and minute here represent midnight). You can think of a ‘LocalDateTime’ as an “invalidated” date and time; there is no information available about the time zone that this date and time belong to, so Noda Time can’t make any guarantees about its ambiguity. The ‘timeZoneId’ in this sample is different than the ones above. In order to use the .NET TimeZoneInfo class we need to provide Windows time zone ids. Noda Time expects an Olson (tz / zoneinfo) time zone identifier and does not currently offer any means of mapping the Windows time zones to their Olson counterparts, though project owner Jon Skeet has said that some sort of mapping will be publicly accessible at some point in the future. I’m making use of the Noda Time ‘DateTimeZone.MapLocalDateTime’ method to disambiguate the original local date time value. This method returns an instance of the Noda Time object ‘ZoneLocalMapping’ containing information about the provided local date time maps to the provided time zone.  The disambiguated local date and time value will be stored in the ‘unambiguousLocalDateTime’ variable as an instance of the Noda Time ‘ZonedDateTime’ object. An instance of this object represents a completely unambiguous point in time and is comprised of a local date and time, a time zone, and an offset from UTC. Instances of ZonedDateTime can only be created from within the Noda Time assembly (the constructor is ‘internal’) to ensure to callers that each instance represents an unambiguous point in time. The value of the ‘unambiguousLocalDateTime’ might vary depending upon the ‘ResultType’ returned by the ‘MapLocalDateTime’ method. There are three possible outcomes: If the provided local date time is unambiguous in the provided time zone I can immediately set the ‘unambiguousLocalDateTime’ variable from the ‘Unambiguous Mapping’ property of the mapping returned by the ‘MapLocalDateTime’ method. If the provided local date time is ambiguous in the provided time zone (i.e. it falls in an hour that was repeated when moving clocks backward from Daylight Savings to Standard Time), I can use the ‘EarlierMapping’ property to get the earlier of the two possible local dates to define the unambiguous local date and time that I need. I could have also opted to use the ‘LaterMapping’ property in this case, or even returned an error and asked the user to specify the proper choice. The important thing to note here is that as the programmer I’ve been forced to deal with what appears to be an ambiguous date and time. If the provided local date time represents a skipped time (i.e. it falls in an hour that was skipped when moving clocks forward from Standard Time to Daylight Savings Time),  I have access to the time intervals that fell immediately before and immediately after the point in time that caused my date to be skipped. In this case I have opted to disambiguate my local date and time by moving it forward to the beginning of the interval immediately following the skipped period. Again, I could opt to use the end of the interval immediately preceding the skipped period, or raise an error depending on the needs of the application. The point of this code is to convert a local date and time to a UTC date and time for use in a SQL Server database, so the final ‘convertedDate’  variable (typed as a plain old .NET DateTime) has its value set from a Noda Time ‘Instant’. An 'Instant’ represents a number of ticks since 1970-01-01 at midnight (Unix epoch) and can easily be converted to a .NET DateTime in the UTC time zone using the ‘ToDateTimeUtc()’ method. This sample is admittedly contrived and could certainly use some refactoring, but I think it captures the general approach needed to take a local date and time and convert it to UTC with Noda Time. At first glance it might seem that Noda Time makes this “simple” code more complicated and verbose because it forces you to explicitly deal with the local date disambiguation, but I feel that the length and complexity of the Noda Time sample is proportionate to the complexity of the problem. Using TimeZoneInfo leaves you susceptible to overlooking ambiguous and skipped times that could result in run-time errors or (even worse) run-time data corruption in the form of a local date and time being adjusted to UTC incorrectly. I should point out that this research is my first look at Noda Time and I know that I’ve only scratched the surface of its full capabilities. I also think it’s safe to say that it’s still beta software for the time being so I’m not rushing out to use it production systems just yet, but I will definitely be tinkering with it more and keeping an eye on it as it progresses.

    Read the article

  • CodePlex Daily Summary for Wednesday, March 17, 2010

    CodePlex Daily Summary for Wednesday, March 17, 2010New Projectschaosreader: A simple RSS reader.CRM 4.0 Customization GUID Update: The CRM 4.0 customization GUID update is an open source C# console application that automatically replaces GUID values in your exported workflow cu...DotNetNuke® Skin Bright: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by Noel Jerke of SiteToolset. This simple and clean business...DotNetNuke® Skin Go: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by DnnGo Corporation. The skin uses web standard DIV+CSS tec...DotNetNuke® Skin J10blend: A DotNetNuke Design Challenge skin package submitted to the "Out of the box" category by Timthy Maler of 2M Studio Design. J10-Black v01.00.00 inc...DotNetNuke® Skin Recipe: A DotNetNuke Design Challenge skin package submitted to the "Standards" category by dnnprofis.at. For mobile devices the skin changes to a mobile...DotNetNuke® Skin SpaceSmurfs: A DotNetNuke Design Challenge skin package submitted to the "Personal" category by Eric Johnson of Personify Design. This fun personal skin was ins...ERDOS6 - Web: A Web Project about ERDOS 6Flickrlight: Flickrlight is a personal fun project out of love of Flickr and Silverlight. You can experience it here: http://www.flickrlight.net.GsGrid: Extracting data from Gaussian grid file and grid file calculationiLocator: iLocator is a collaborative educational mapping game for children developed on Microsoft Surface. This game encourages players to collaborate with ...Javascript CallObject SOAP AJAX Helper: CallObject is a Javascript based AJAX helper, it facilitates wrapping of basic soap calls (as long as simple data types are used), asynchronous ret...kbTrainer: kbTrainer is a simple to use HTML application for typing speed training. A lot of features completed in basic. 2 learning keywords layouts -- engli...Laboratório de Engenharia de Software - Projeto: Criado para estudar e aplicar novas tecnologias web.Maxilds Powershell Scripts: Repo of my powershell scriptsNamespacifier: Namespacifier is a C#.NET library and console application to fix XML documents containing multiple default namespaces. It gives prefixes to defaul...OData SDK for Objective-C: This is a CTP of the OData SDK for Objective-C. The library targets iPhone devices and Mac OS X and it is designed to facilitate the connection wit...Open Data App Framework (ODAF): The Open Data Application Framework (ODAF) is a framework that allows cities to easily map existing civic Open Data landmarks, and allow users to r...QuickieB2B: QuickieB2B is web application which main target is to provide quick info about products. It's designed for small companies who have a big number of...RayView: Rayview is an easy-to-use Raytracing-Framework based on Microsoft XNA.Robotics Studio application to navigate Lego Mindstorms robot through labyrinth: A project for Software Systems Analysis and Design Tools subject at the Kaunas University of Technology. The main point of the project is to code L...SharePoint Icon Integration: SharePoint Icon Integration makes it easier for SharePoint Administrators / Developers to add a icon (pdf) to the SharePoint farm. You will no long...TestVersion: Testing VersionieringTimecard: SoftSource Timecard project.T-shirt Cannon: So the Coding4Fun team had two weeks to build two robots able to drive, aim, and shoot t-shirts with a Windows Phone during a MIX10 Keynote demo of...USTF: This project is a bit secretive right now.Windows Azure Command-line Tools for PHP Developers: The “Windows Azure Command-line tools for PHP” provide a command-line experience to developers who wish to develop, package, and deploy PHP applic...New ReleasesCaramel Engine: CaramelEngine Alpha Build 0.0.0.1a: This is an early alpha release of the Engine and it's functionality. Be sure to have the using CaramelEngine statement. This release is for people...Coot: Preview: Basic preview On the first use you have to click Create New Session and Login. After this you can just click Screen Saver each time. Settings sho...CycleMania Starter Kit EAP - ASP.NET 4.0 Problem - Design - Solution: Cyclemania 0.08.32: The latest alpha release.DeepZoomContainer, Expanded DeepZoom for Silverlight & Windows Phone 7 Series: Release ver. 1.20 for Windows Phone 7 Series: SolutionMerge PathAnimation solution into one MouseWheel elimination PathAnimationWP7 Port DeepZoomContainerProject rebuilt for WP7 support De...Desktop Google Reader: 1.3 (the social release): NewsSharing Liking Mail item Labels / Tags Send to Twitter Read It Later http://readitlaterlist.com/ Instapaper http://www.instapaper.com/ Favicons...DotNetNuke® Blog: 04.00.00 RC 2: PLEASE NOTE: Please do not upgrade previous version of the Beta releases - please start from 03.05.01 This is a RELEASE CANDIDATE, and as such ...DotNetNuke® Community Edition: 05.03.00: New FeaturesTemplated User Profiles - User profile pages are now publicly viewable Photo field in User Profile - Users can upload a photo to thei...DotNetNuke® Skin Bright: Bright Package 1.0.0: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by Noel Jerke of SiteToolset. This simple and clean business...DotNetNuke® Skin Go: Go Package 1.0.0: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by DnnGo Corporation. The skin uses web standard DIV+CSS tec...DotNetNuke® Skin J10blend: J10 Blend Package 1.0.0: A DotNetNuke Design Challenge skin package submitted to the "Out of the box" category by Timthy Maler of 2M Studio Design. J10-Black v01.00.00 incl...DotNetNuke® Skin Recipe: Recipe Package 1.0.0: A DotNetNuke Design Challenge skin package submitted to the "Standards" category by dnnprofis.at. For mobile devices the skin changes to a mobile f...DotNetNuke® Skin SpaceSmurfs: Space Smurfs Package 1.0.0: A DotNetNuke Design Challenge skin package submitted to the "Personal" category by Eric Johnson of Personify Design. This fun personal skin was ins...Dynamo: Dynamo v0.1 Beta: The following is included: Dynamo dlls Antlr dlls Hello world Simple Plugin example Application Dependency injection Singleton Managment ...ExtremeML: ExtremeML v1.0 Beta 1: Timed to accompany the RTM release of the OpenXML SDK v2.0, this is the first Beta release of ExtremeML (it was previously classified as a preview ...Family Tree Analyzer: Version 1.1.1.1: Version 1.1.1.1 Lots of Gedcom parsing fixes it should crash a whole lot less often and tolerate more "interesting" or "quirky" Gedcom entries. Add...Family Tree Analyzer: Version 1.2.0.1: Version 1.2.0.1 Added option to treat residence facts as Census Facts IGI Search now permits default country selection ie: what to use if it doesn...Flickrlight: Flickrlight: Current release is for idea sharing. There are not many design patterns being used. Please bare with the mess. :-) In order to run the applicat...Gherkin editor: Alpha 0.1: Most of the code at this point is the same as the Avalon.Sample from code project, just changed the name, removed extra languages and added syntax ...GsGrid: gsgrid1.6.4: gsgrid1.6.4GsGrid: gsgrid1.6.4-src: gsgrid1.6.4-srcHTML Template Repeater Module: Version 01.00.02: GeneralThe HTML Template Repeater Module is a direct replacement for the Core DotNetNuke Text/HTML module. Use it where you need to repeat the form...Images Compiler: Release 0.1: Last alpha buildJavascript CallObject SOAP AJAX Helper: Beta Release, 0.2.1: Beta Release, 0.2.1 Contains only core objectskbTrainer: kbtrainer 1.25u: kbTrainer is a simple to use speed typing training HTML application. A lot of features. All ither info availiable on http://code.google.com/p/kbtr...MapWindow6: MapWindow 6.0 msi (March 16): This version fixes a bug where selected points were not drawing correctly.Mesopotamia Experiment: Mesopotamia 1.2.43: Release Notes New Features - Scenario Name on title bar - Show organisms in Scnearios with simple stats Bug Fixes - Removed app domain recyling an...MFCMAPI: March 2010 Release: If you just want to run the tool, get the executable. If you want to debug it, get the symbol file and the source. Build: 6.0.0.1018 The 64 bit bu...MVVM Light Toolkit: MVVM Light Toolkit V3: Download the Zip file and extract it to a local folder. Then, follow the instructions on the Installation page http://www.galasoft.ch/mvvm/installi...NETXPF: 1.0.2: Changes: - Added a class "IOUtils" with methods for reading streams and GZip-compressing HTTP responses - Fixed a bug in the size formatter (excep...OData SDK for Objective-C: OData SDK for Objective-C CTP: The current release supports read-only operations only and it has been tested on a limited set of scenarios. The download include a sample iPhone a...Open Data App Framework (ODAF): ODAF 1.0: Initial beta release.Selection Maker: Selection Maker 1.1: New FeaturesContext Menu for ListView added Bug FixesFixed: If the users press Copy/Cut Button when no item is selected in ListView the ListView cl...Selection Maker: Selection Maker 1.2: Bug Fixes:a minor bug fixedSimple.NET: Simple.Mocking 1.0.0.5: Initial version of a new mocking framework for .NET Revision 1: Expect.AnyInocationOn<T>(T target) changed to Expect.AnyInocationOn(object target...SQL Server Extended Properties Quick Editor: New release 1.5.4: Whats new: Move preferences to application settings and add a form to edit preferences. Support to add, modify and delete operations could be made ...SuperModel - A Dynamic View-Model Generator: 1.0.0.0 - Tyra: The final 1.0 release, now less intrusive! If you don't want to implement ISuperModel, simply implement INotifyPropertyChanged.Timecard: Timecard Initial Release: The zipped version of the Initial Checkin.Transparent Persistence.Net: TP.Net 0.1.0: This is the initial alpha release. It's working for small set of use-cases (basic access to Cassandra).VCC: Latest build, v2.1.30316.0: Automatic drop of latest buildVFPnfe: Projeto Ajuda PAF-ECF: Este projeto visa ajudar aos desenvolvedores para homologação do PAF-ECF , sob licença publica GNU/GPL para ver mais detalhes do mesmo assista o vi...Visual Studio DSite: Gif Animator: This program will make an animate gif. (Program written in Vb.Net 2008)Most Popular ProjectsMetaSharpLiveUpload to FacebookSkype Voice ChangerLiveUpload to YouTubeSIPSorceryChartPart for SharePointTFS Branching Guide 2.0TouchFlo DetacherNPandaySnippet EditorMost Active ProjectsLINQ to TwitterRawrOData SDK for PHPDirectQpatterns & practices – Enterprise LibraryBlogEngine.NETN2 CMSOpen Data App Framework (ODAF)NB_Store - Free DotNetNuke Ecommerce Catalog ModuleMapWindow6

    Read the article

  • How is WPF Data Binding using Object Data Source in Visual Studio 2010 done?

    - by Rob Perkins
    This is probably mostly a question about how to use the VS 2010 IDE tools in a way the Microsofties didn't specifically intend. But since this is something I immediately tried without success. I have defined a .NET 4.0 WPF Application project with a simple class that looks like this: Public Class Class1 Public Property One As String = "OneString" Public Property Two As String = "TwoString" End Class I then defined it as an "Object Data Source" in VS2010, using the IDE's "Add New Data Source..." feature. This exposes the class members in a GUI element in the IDE as given in this image: Dragging "Class1" from that tool to the surface of "Window1.xaml" in a default "WPF Application" results in the design view looking like this: And generated XAML like this: <Window x:Class="Window1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="Window1" Height="133" Width="170" xmlns:my="clr-namespace:WpfApplication1" mc:Ignorable="d" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" > <Window.Resources> <CollectionViewSource x:Key="Class1ViewSource" d:DesignSource="{d:DesignInstance my:Class1, CreateList=True}" /> </Window.Resources> <Grid DataContext="{StaticResource Class1ViewSource}" HorizontalAlignment="Left" Name="Grid1" VerticalAlignment="Top"> <Grid.ColumnDefinitions> <ColumnDefinition Width="Auto" /> <ColumnDefinition Width="Auto" /> </Grid.ColumnDefinitions> <Grid.RowDefinitions> <RowDefinition Height="Auto" /> <RowDefinition Height="Auto" /> </Grid.RowDefinitions> <Label Content="One:" Grid.Column="0" Grid.Row="0" HorizontalAlignment="Left" Margin="3" VerticalAlignment="Center" /> <TextBlock Grid.Column="1" Grid.Row="0" Height="23" HorizontalAlignment="Left" Margin="3" Name="OneTextBlock" Text="{Binding Path=One}" VerticalAlignment="Center" /> <Label Content="Two:" Grid.Column="0" Grid.Row="1" HorizontalAlignment="Left" Margin="3" VerticalAlignment="Center" /> <TextBlock Grid.Column="1" Grid.Row="1" Height="23" HorizontalAlignment="Left" Margin="3" Name="TwoTextBlock" Text="{Binding Path=Two}" VerticalAlignment="Center" /> </Grid> Note the data bindings Text="{Binding Path=One}" and Text="{Binding Path=Two}" in the TextBlock elements. Code-behind for Window1.xaml has this in Window_Loaded: Class Window1 Private m_c1 As New Class1 Private Sub Window1_Loaded(ByVal sender As Object, ByVal e As System.Windows.RoutedEventArgs) Handles Me.Loaded Dim Class1ViewSource As System.Windows.Data.CollectionViewSource = CType(Me.FindResource("Class1ViewSource"), System.Windows.Data.CollectionViewSource) 'Load data by setting the CollectionViewSource.Source property: 'Class1ViewSource.Source = [generic data source] Me.DataContext = m_c1 End Sub End Class Running the application produces this output: The expected result was that "OneString" would appear next to "One" and "TwoString" next to "Two" in the running window. The question is: Why didn't this work? What will work instead? If I put bindings in a DataTemplate, it works. Blend, with its sample data stuff, implied that this should work, but it doesn't. I know I'm missing something pretty fundamental here; what is it?

    Read the article

< Previous Page | 32 33 34 35 36 37 38 39  | Next Page >