Search Results

Search found 64721 results on 2589 pages for 'windows usb drive'.

Page 36/2589 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

  • Hard drive and DVD drive are not being detected by the BIOS

    - by Shah Nsd
    My hard drive and DVD drive are not being detected by the BIOS when I go in to the boot option menu by pressing F12. When I put the hard drive in a different computer it's being detected. I am assuming it's either the mother board or the BIOS. Since the HDD is not being detected I have installed Ubuntu on a flash drive, but even that has become so slow, that it takes around 5 minutes for it to boot. I want to flash the BIOS before I think of changing the motherboard. I have downloaded the updated file and it has a flash.bat and a afudos.exe. I have to run the .bat file. I downloaded the Dos in a box and went to the DOS directory where the .bat file is and tried to run it, but it gives me the error message "This program cannot run under this operating system" Any help would be appreciated

    Read the article

  • Old hard drive file permissions still there

    - by blsub6
    I have a new hard drive, put Windows 7 on it and want to get all the files off of my old hard drive. I put in my old hard drive as a slave drive. I can see the files but when I try to move 'em, it tells me that I'm not the owner of the file. I try to take ownership of the file and it doesn't work (it doesn't tell me that I can't take ownership of it, it goes through, just gives me the same error when I try and open the file again). I've tried modding the permissions, no dice. Anything else I can try?

    Read the article

  • Windows 7 randomly installs an "Unknown Device"

    - by Amazed
    Rarely (several days to weeks between occurrences,) and seemingly at random, I get a balloon notification from Windows 7 (x64 SP1 Home Premium) that it is installing hardware for me. However, no new hardware has been installed or plugged in! When I click the balloon it doesn't give me any useful information: Looking in the event log, I find this entry: Event ID: 20001 Source: UserPnp Task Category: 7005 Message: Driver Management concluded the process to install driver FileRepository\usb.inf_amd64_neutral_153b489118ee37b8\usb.inf for Device Instance ID USB\VID_0000&PID_0000\6&3AF9A177&0&0060&&02 with the following status: 0x0. It appears to be USB related. My motherboard has both USB 2.0 and 3.0 controllers. My keyboard and mouse are plugged into the 2.0 slots and the data/recharge cable for a tablet (but not the tablet itself) was plugged in to the 3.0 slot. No other USB devices have been attached for several days/reboots. Why is Windows doing this?

    Read the article

  • USB flash drive unreadable after a few minutes on Windows 8

    - by B Sharp
    I recently got a new computer with Windows 8. I a have a number of large backup files I am moving from my old PC to my new one. I was able to successfully copy the files to a couple 16 GB flash drives. When I try to copy the files to my new computer, the process starts just fine but after copying about 4 GB of files, the copy stops. If I look at the drive in explorer, the drive is there, but I just get a busy cursor that stays indefinitely if I click it. If I unplug the flash drive and plug it back in, everything is fine again... for a couple minutes. I've tried copying from both flash drives with the same result. I've also tested this on the USB 2.0 and 3.0 ports on my motherboard with the same result (the drives are USB 2.0) It's also puzzling that this is happening since I previously used one of the same flash drives to install Windows 8 on this computer in the first place without any difficulty.

    Read the article

  • Recovering drive via boot to Win7 setup command prompt

    - by Valamas
    I am trying to recover data from two old IDE drives. Drive1 has been successful, but something is wrong with Drive2. It does not appear as a drive letter. Due to limited legacy hardware, the only way i can see these drives is to boot using windows 7 setup and goto the command prompt. Without going further as to why, my question is how i can access the data in this command prompt. I discovered DISKPART command and while a first time user, it looked like something that can fix my problem. Here are the results of my diskpart commands. At the bottom is a image of the commands taken with a camera. The Drive2 is present because when using the diskpart command, I can see it. How can I copy the information using a robocopy script if the drive letter is not available? how can I assign a drive letter? Is there any repair command I need to execute? When i execute DISKPART, the following is what i see. DISKPART> LIST DISK Disk### Status Size Free Disk 5 Online 37 GB 2048 KB So then I select disk 5. DISKPART> SELECT DISK 5 "Disk 5 is now the selected disk" When I list partition DISKPART> LIST PARTITION Partition ### Type Size Partition 1 Primary 101 MB Partition 2 Primary 37 GB So I select partition 2 "Partition 2 is now the selected partition." I then try to assign a drive letter DISKPART> ASSIGN LETTER=G "There is no volume specified." "Please select a volume and try again." When i list volume the drive is not present. DISKPART> LIST VOLUME Result of the above commands

    Read the article

  • installing ubuntu 12.04 along windows xp and windows 7

    - by Anand A J
    I have Windows XP installed on C drive and Windows 7 installed on F drive. I want to install Ubuntu 12.04 alongwith Windows (keeping both XP and 7) in drive G with out losing any data stored in the computer. I have a hard disk of 500 GB size with C (14.8 GB left),D,E,F, and G (15.7 GB left). I tried to install Ubuntu 12.04 from DVD and getting stuck at the time of selecting partitions .! How to select the device for boot loader installation? Will the installation of Ubuntu into G drive affects the data stored in the hard disk or in G drive especially? After installing Ubuntu can I use Windows XP and Windows 7? This is my first attempt to use Ubuntu. Can any body help me please?

    Read the article

  • Why are USB 2.0 devices crashing my system?

    - by BenAlabaster
    Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

    Read the article

  • Windows 7 - Home Drive Map Fails

    - by Ed Fries
    Server 2003 SP2 (not R2) with 2 new Win 7 Pro workstations. Home Drive is set in AD (not GP) to map to \\server\users\username. Home Drive map fails, other network drives map correctly. No error logged on server or PC, Win 7 shows "Could not reconnect all network drives." There is no Y: (Home Drive) listed, either in the GUI or via Net Use. Manual map via batch file in startup group with the same path works correctly? Home Drive map works correctly on XP workstations.

    Read the article

  • Google Drive desktop client not updating existing files from other users

    - by cqm
    I've looked around and there doesn't really seem to be any troubleshooting information for the Google Drive desktop client. It all assumes you are using Google Docs on the web. Anyway, my team is trying to use Google Drive like Dropbox, where multiple people are editing files shared amongst them through the desktop, such as images. Dropbox is really good at noticing when a checksum for a file is changed, and syncing it. Google Drive's desktop client seems not to do this at all. Google Drive desktop client seems to only sync newly created files and not giving any notification at all that there is a modified version, it will never sync it, even though going online and opening that file will show the modified version. Is there any way to fix this? and the answer has nothing to do with proxy or firewall configurations. Team is using computers running OSX and Windows.

    Read the article

  • Drive letter not appearing after heat-related crash

    - by NickAldwin
    I recently had my old PC (has 3 physical hard drives partitioned into 6 partitions) off while on vacation. When I came back, I turned it on. I hadn't realized the room was warmer than it usually is due to hot weather while I was away. The computer was extremely slow to start up, then it crashed. When i rebooted, it got halfway through chkdsk on one of the non-system partitions, then crashed again. I opened it up and felt the hard drives and immediately shut down the computer and moved it to my basement to cool down because it was so hot. I left it there for a length of time while I reinstalled the A/C. I have now turned it on again. It is working fine, and every drive except for the one with the partition that was being checked has appeared in Windows. I scheduled chkdsk for all of the other partitions anyway, just in case, but I'm worried about that drive. I'm pretty sure the drive itself hasn't broken but that crashing in the middle of a chkdsk repair may have corrupted the data. What would you do in this situation? Most of the data on that drive was backed up, so it's not a huge deal if I lost it, but I'd like to get it back if I could. I also would love to regain usability of the drive, even if I have to wipe it -- but that's a last-resort sort of thing. What do you suggest I do?

    Read the article

  • Ubuntu not showing hard drive

    - by ojek
    I have a laptop which had a broken installation of Windows 7 installed on it. I created a Ubuntu live USB and tried installing Ubuntu over that Windows 7. After a few minutes, I got an error message, so I needed to restart the computer. Now the laptop says that there is no bootable device - reasonable message given that there was an error during Linux installation. However: BIOS can see my hard drive, When I start Ubuntu in live mode, and try either sudo fdisk -l or gparted, it doesn't show any hard disk drives. I am 90% sure that the hard drive is broken, but it is weird that BIOS can see it, and Ubuntu doesn't. How can I be 100% sure about that hard drive? Is there any additional way of detecting my hard drive from Ubuntu?

    Read the article

  • Hard drive causing BSOD

    - by JoshIrving
    I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

    Read the article

  • Hard drive causing BSOD

    - by JoshIrving
    I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

    Read the article

  • Configuring Windows Server Backup Destination Drive Sets

    - by Nicholas
    Is it possible to set up the standard backup system in SBS 2011 (or Server 2008 R2) to use an internal drive as a destination as well as external drives? Before you say yes, from my tests and from what I've read on the web, backups with internal drives included as a destination always seems to prefer the internal drive over connected external ones. (Regardless of what drive might be marked as 'active'). So no data ever gets written to a plugged in external drive. In my opinion external drives should always have priority over internal drives or including them is pointless.

    Read the article

  • Backup windows image to thumb drive?

    - by Dean
    I recently bought a new netbook from Malasia. It doesn't have a brand name, or officially supporting drivers. It came with a version of windows, and working drivers for all the hardware - but I want to install Ubuntu on here. Being a netbook, it has no CD/DVD drive. I want some free easy to use software to image the entire drive onto a thumb drive, which I could later use to boot up a recovery program to reinstall windows, should I fail to get all the hardware supported on Linux. I have already done some research and found driver backup/restore software in this thread, and will probably use that failing a more all-encompasing solution.

    Read the article

  • usb flash drives how to fix ?

    - by madyotto
    Hi all I have recently purchased some so called 256gb Kingston drives that are fake I used a program called check flash and few other to check for dead sectors and read speed and read and write speed the results are as follows: they were reading at 1.35 mbps at best they read and wrote at 0.95 mbps and had a hell of a lot of dead sectors so what I ask is: Is there a way to drop the size to improve speed Is there any other way to improve speed How can I stop the device from addressing the dead sectors Any help will be much appreciated ALL THE THANKS (MADYOTTO)

    Read the article

  • USB Permission - Write protection

    - by dekhadmai
    I have an external harddisk and my friends asked for it. The point is I don't trust in his anti-virus software. Is there anyway to allow some folders (I prepare hdd space for him) to write-able and all others is read-only ? or is there a software that can do like this ? And it would be great if I can have full access on my computer ONLY (may be with some specific software on my PC) and without having to modify anything. I don't ask for hdd-encryption since I only want to limit the area of write-able folder (and allow my friend to read through all my data), later I can scan for virus myself only in that area ... scanning entire hdd with 500gb/friend is not fun at all ! Sorry if this doesn't seems like the programming questions. Any help would be appreciate, Thank you.

    Read the article

  • IOS: How to uplaod a file to specific google drive folder using google drive sdk library

    - by loganathan
    I integrated google drive sdk with my ios app. But i do not know how to upload a file to google drive specific folder. Here the code am using to upload the file. But this one uploading the file to my google drive root folder. Any one share a code to upload a file to google drive specific folder?. My Code: -(void)uploadFileToGoogleDrive:(NSString*)fileName { GTLDriveFile *driveFile = [[[GTLDriveFile alloc]init] autorelease]; driveFile.mimeType = @"application/pdf"; driveFile.originalFilename = @"test.doc"; driveFile.title = @"test.doc"; NSString *filePath = [LocalFilesDetails getUserDocumentFullPathForFileName:fileName isSignedDocument:YES]; GTLUploadParameters *uploadParameters = [GTLUploadParameters uploadParametersWithData:[NSData dataWithContentsOfFile:filePath] MIMEType:@"application/pdf"]; GTLQueryDrive *query = [GTLQueryDrive queryForFilesInsertWithObject:driveFile uploadParameters:uploadParameters]; [self.driveService executeQuery:query completionHandler:^(GTLServiceTicket *ticket, GTLDriveFile *updatedFile, NSError *error) { if (error == nil) { NSLog(@"\n\nfile uploaded into google drive\\<my_folder> foler"); } else { NSLog(@"\n\nfile uplod failed google drive\\<my_folder> foler"); } }]; }

    Read the article

  • Remote Desktop access Windows 7 system from Windows 8

    - by Prabhat
    I have 2 systems; Windows 7 & Windows 8. Both are connected to WiFi router. They have been assigned address 192.168.2.8 & 192.168.2.9 respectively. I have added them to home group. I am able to ping and connect Windows 8 system from Windows 7. I am having trouble connecting Windows 7 system from Windows 8 system. I can't even ping Windows 7 system. Windows 7 system's user is administrator (default administrator account from secpol.msc). File sharing, Remote Access, network discovery are all enabled. Someone please help me connect. EDIT : I found that this is the issue of Kaspersky Internet Security 2012. If I disable firewall, it works. I tried opening port 3389 in Kaspersky. It is still blocking access.

    Read the article

  • Windows 7 - How to access my documents from Windows 8 (dual boot)

    - by msbg
    I am dual booting Windows 7 and Windows 8 on two different partitions of the same drive: Win7: (C:) Win8: (D:) I am trying to get access to my Win7 user folder (C:\Users\Mason) in order to access my Win7 documents folder (C:\Users\Mason\Documents) from Windows 8. When I try to on Windows 8, I get an error message saying "You don't have permission to access this folder. Click here to permanently get access to this folder". When I click, the progress bar in Windows Explorer slowly moves to the maximum and disappears. When I try opening the folder, I get the same error message. When editing security permissions for the folder in Windows 8, Explorer freezes. I do not know how to remove the restrictions from Windows 7. I checked the Windows 8 user folder (D:\Users\Mason) and it had the group or user name: "S-1-5-21-936898901-3363470404-1273668825-1001". I tried copying and pasting it into the Win7 User Folder Permissions, but got the error "An object with the following name cannot be found". How would I access my folders?

    Read the article

  • How to Restore the Real Internet Explorer Desktop Icon in Windows 7

    - by The Geek
    Remember how previous versions of Windows had an Internet Explorer icon on the desktop, and you could right-click it to quickly access the Internet Options screen? It’s completely gone in Windows 7, but a geeky hack can bring it back. Microsoft removed this feature to comply with all those murky legal battles they’ve had, and their alternate suggestion is to create a standard shortcut to iexplore.exe on the Desktop, but it’s not the same thing. We’ve got a registry hack to bring it back. This guest article was written by Ramesh from the WinHelpOnline blog, where he’s got loads of really geeky registry hacks. Bring Back the Internet Explorer Namespace Icon in Windows 7 the Easy Way If you just want the IE icon back, all you need to do is download the RealInternetExplorerIcon.zip file, extract the contents, and then double-click on the w7_ie_icon_restore.reg file. That’s all you have to do. There’s also an undo registry file there if you want to get rid of it. Download the Real Internet Explorer Icon Registry Hack Manual Registry Hack If you prefer doing things the manual way, or just really want to understand how this hack works, you can follow through the manual steps below to learn how it was done, but we’ll have to warn you that it’s a lot of steps. Launch Regedit.exe using the Start Menu search box, and then navigate to the following location: HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30309D} Right-click on the key on the left-hand pane, choose Export, and save it to a .REG file (say, ie-guid.reg) Open up the REG file using Notepad… From the Edit menu, click Replace, and replace every occurrence of the following GUID string {871C5380-42A0-1069-A2EA-08002B30309D} … with a custom GUID string, such as: {871C5380-42A0-1069-A2EA-08002B30301D} Save the REG file and close Notepad, and then double-click on the file to merge the contents to the registry. Either re-open the registry editor, or use the F5 key to reload everything with the new changes (this step is important). Now you can navigate downto the following registry key: HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30301D} \ Shellex \ ContextMenuHandlers \ ieframe Double-click on the (default) key in the right-hand pane and set its data as: {871C5380-42A0-1069-A2EA-08002B30309D} With this done, press F5 on the desktop and you’ll see the Internet Explorer icon that looks like this: The icon appears incomplete without the Properties command in right click menu, so keep reading. Final Registry Hack Adjustments Click on the following key, which should still be viewable in your Registry editor window from the last step. HKEY_CLASSES_ROOT\CLSID\{871C5380-42A0-1069-A2EA-08002B30301D} Double-click LocalizedString in the right-hand pane and type the following data to rename the icon. Internet Explorer Select the following key: HKEY_CLASSES_ROOT\CLSID\{871C5380-42A0-1069-A2EA-08002B30301D}\shell Add a subkey and name it as Properties, then select the Properties key, double-click the (default) value and type the following: P&roperties Create a String value named Position, and type the following data bottom At this point the window should look something like this: Under Properties, create a subkey and name it as Command, and then set its (default) value as follows: control.exe inetcpl.cpl Navigate down to the following key, and then delete the value named LegacyDisable HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30301D} \ shell \ OpenHomePage Now head to the this key: HKEY_LOCAL_MACHINE \ SOFTWARE \ Microsoft \ Windows \ CurrentVersion \ Explorer \ Desktop \ NameSpace Create a subkey named {871C5380-42A0-1069-A2EA-08002B30301D} (which is the custom GUID that we used earlier in this article.) Press F5 to refresh the Desktop, and here is how the Internet Explorer icon would look like, finally. That’s it! It only took 24 steps, but you made it through to the end—of course, you could just download the registry hack and get the icon back with a double-click. Similar Articles Productive Geek Tips Quick Help: Restore Show Desktop Icon in Windows VistaQuick Help: Restore Flip3D Icon in Windows VistaAdd Internet Explorer Icon to Windows XP / Vista DesktopHide, Delete, or Destroy the Recycle Bin Icon in Windows 7 or VistaBuilt-in Quick Launch Hotkeys in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa ! Use Printflush to Solve Printing Problems Icelandic Volcano Webcams Open Multiple Links At One Go

    Read the article

  • Create windows XP's live USB using ubuntu

    - by Avnish
    My hard disk crashed.. I can run Ubuntu using a pendrive by making a live USB of Ubuntu, which I made using Windows 7. In the similar way, I want to run Windows XP too using another pen drive (without hard disk) and I want to make it from Ubuntu (12.04). The resources I have are Ubuntu's live USB, Windows XP and Windows 7 installation disk, some blank DVDs but no hard drive. I have very basic knowledge of Linux. Thanks

    Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >