Search Results

Search found 15499 results on 620 pages for 'non obvious'.

Page 360/620 | < Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• "Windows cannot find" file when opening Excel spreadsheet

  - by DanH

  For all of my Excel spreadsheets when I attempt to open them (by double-clicking in explorer) I get the message "Windows cannot find C:...". The files are there, and are valid zip files as seen by 7-Zip. There are no apparent lock files in the directories. I did just install Norton-360 over the weekend (replacing Kasperski), but the Norton log shows no events related to Excel. However, while installing Norton I did reboot with some Excel files open. Presumably something is hosed in my Excel configuration but I don't know what. Update (Before actually posting) -- I found an article that suggested turning off Advanced Option "Ignore other applications that use DDE", then doing excel.exe /unregister followed by excel.exe /register. I tried this but I suspect that the two Excel calls were ignored (Excel opened, but no obvious change). With that option off the spreadsheets load OK, but not with it on. And, curiously, spreadsheets load OK with the option on or off if I open Excel first and then open the spreadsheet in it. Does anyone have any idea what effect leaving that option off will have? Update 2 -- I tried running the "repair" option. It said it corrected a couple of config things (without saying what they were), but I still get a failure if I double-click an Excel file with the "Ignore other applications..." option checked. Update 3 -- I managed to fix this problem, but failed at the time to come back and say what I did, and now I can't remember for sure. But I think it had something to do with "Options"/"Save" and some of the values there. Something to do with AutoRecover, perhaps. (Possibly there was a file in recovery and I had to specify "Disable AutoRecover for this workbook" to let bring-up get past it. Or perhaps the AutoRecover file location was hosed.) Anyway, if it happens to someone else, and you find the fix, post it below and I'll mark it answered.

  Read the article

• Alternatives to ntbackup

  - by Chris J

  Is anyone aware of any good (for a given value of "good") alternatives to ntbackup? There's a few quirks with ntbackup that I still find odd, and occasionally (and for no obvious reason) ntbackup just doesn't back up - usually complaining about that the wrong tape's inserted even though it's been told to just use the tape that's in the drive regardless. I've experiemented with cygwin's tar and cpio and Win32 ports of these utilities, but I've not had any luck getting them to see the tape device (so if someone does use these utilities to write to a tape device, also be interested to know how). Essentially all I'm looking for is a reliable program that I can tell to back-up a list of locations to the tape, and not to care about anything like formatting tapes, or sticking volume labels on them (and conversely then makes it fairly straightforward to restore off as well). On the flip-side, I don't want something that will attempt to manage our tapes. Don't get me wrong here -- ntbackup can do the job, but its quirks are making look at possible alternatives. Any suggestions? If it's open source, even better.

  Read the article

• OpenLDAP Authentication UID vs CN issues

  - by user145457

  I'm having trouble authenticating services using uid for authentication, which I thought was the standard method for authentication on the user. So basically, my users are added in ldap like this: # jsmith, Users, example.com dn: uid=jsmith,ou=Users,dc=example,dc=com uidNumber: 10003 loginShell: /bin/bash sn: Smith mail: [email protected] homeDirectory: /home/jsmith displayName: John Smith givenName: John uid: jsmith gecos: John Smith gidNumber: 10000 cn: John Smith title: System Administrator But when I try to authenticate using typical webapps or services like this: jsmith password I get: ldapsearch -x -h ldap.example.com -D "cn=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" Enter LDAP Password: ldap_bind: Invalid credentials (49) But if I use: ldapsearch -x -h ldap.example.com -D "uid=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" It works. HOWEVER...most webapps and authentication methods seem to use another method. So on a webapp I'm using, unless I specify the user as: uid=smith,ou=users,dc=example,dc=com Nothing works. In the webapp I just need users to put: jsmith in the user field. Keep in mind my ldap is using the "new" cn=config method of storing settings. So if someone has an obvious ldif I'm missing please provide. Let me know if you need further info. This is openldap on ubuntu 12.04. Thanks, Dave

  Read the article

• Can a hardware firewall block a server accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. Is this possible? Does 'UNC traffic' go out of the machine and then back in again?

  Read the article

• Slow performance on VMWare Linux server after Tomcat install

  - by Loftx

  We have a VMWare ESXi 4.1 server hosting a number of Linux and Windows guests. Recently a new Linux guest was added to this server and seemed to be performing well. Tomcat and some other applications on this server were then installed which seem to have caused the server to run really slowly without any obvious resource issues. Slow performance include: The time taken to bring up the password prompt over ssh takes a few seconds when it was previously instantaneous. The time taken to unzip a zip file which was previously a few seconds now takes around 30 seconds The time taken to compile vmware tools has increased by similar factors Both the VMWare console and monitoring commands don't report any issues with high CPU or memory usage but something is obviously slowing the server down somehow. Does anyone have any ideas what may be causing this issue and how it can be resolved? Thanks, Tom Edit As per your questions I’ve looked at some of the performance indicators on both the VM host and VM guest indicated. Firstly I tried reserving the full amount of memory (3gb) for this VM – no other machines on this server have any memory reservation. The swap in rate and swap out rate for the VM host and guest are now both zero. Balloon memory on the guest is zero and on the host is 3.5gb (total memory on the host is 12gb) The swap rate for the guest is also zero. Swap used by the host is 200mb on average. Compression and decompression rates for the host and guest are zero. Command aborts for the host are zero. Read latency is very low – maximum 10ms average 0.8ms. Write latency is higher – a few spikes to 170ms but mostly around 25ms – is this bad? Queue command latency is zero . Physical disk read latency averages 5ms but often 10ms Physical disk write latency averages 15ms but is often 20ms I hope this helps - let me know if you need any more information.

  Read the article

• How to copy a bunch of pages? Is there a 3rd party tool?

  - by unknown (yahoo)

  (I asked the following question at the DNN forum, and also at snowcovered. Nobody knew of such an obvious time-saver being for sale. I'm posting here in case anybody knows of a freeware module that might do this.) By "groups of dnn pages", I mean pages that form a hierarchy (not necessary a hierarchy that is headed with a page at the same level as the Home page.) I know that I can copy web pages, one by one, using the admin login via the web-based dnn interface. But, I'd prefer a script or wizard, of some sort (that runs scripts behind the scenes) that can allow me to 1) specify a web page that I want to copy (along with the hierarchy of pages under it) 2) specify the names and titles of the new top-level pages 3) specify whether the contained modules of the top-level page that I want to copy is to be : ( ) New ( ) Copy ( ) Reference (as in the web-based interface) 4) repeat 3) for each of the source pages in the hierarchy that I want to copy You might say that I am looking to do something similar to creating a portal web site based on a template, except that it's not an entirely new website - instead it's a section of the current web site. I might want to do this because I have an organization which is broken into chapters, and I want each chapter to have, say, it's own General Information page (which acts like it's home page), and underneath that, in it's hierarchy, a Contact Info page and an Events page. so: Home Page   General Information Page     Contact Info     Events -- Home Page   General Information Page     Contact Info     Events   General Information Page Kiwanis - Bloomfield     Contact Info     Events   General Information Page Kiwanis - Dayton     Contact Info     Events If I have 200 chapters, I certainly don't want to copy those 3 web pages using the web based interface, as that would take a long time. (And imagine if each chapter's new sub-website had 30 pages!) I just want to specify the parameters of a copy process, then press a button, and let the system do the rest.

  Read the article

• Win7 Command Prompt drives not available

  - by jmerrill

  I have the opposite problem compared to the author of this question: Hard drive access denied from Windows Explorer (but works from command prompt as Admin) I can see all the drive letters for a particular server in Windows Explorer, and can navigate through them exactly as would be expected. The drive letters are displayed in Explorer in parens to the right of the path info -- finalpathportion (\\server\otherpathportions) (driveletter:) e.g. jmerrill (\\server\users) (H:) But the drive letters are not usable in a "Run as Administrator" command prompt. They have worked in the past, but I have since rebooted. I thought that perhaps I had to start a new command prompt having visited them in Explorer -- but that did not help. "net use" in the command prompt shows Unavailable H: \\server\users\jmerrill Microsoft Windows Network with similar info for the other drives. I can do net use h: /d net use h: \\server\users\jmerrill for each drive, and get the letters to be available in the command prompt. It is perhaps obvious that I don't think that it should be necessary to do that. Does anyone have any ideas?

  Read the article

• Avoiding DNS timeouts when a dns server fails

  - by Neil Katin

  We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

  Read the article

• Rebuild Apple RAID set

  - by Clinton Blackmore

  We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

  Read the article

• Do registry issues with Win7 persist through a recovery from a system image?

  - by user59089

  So I need a bit of advice, please; here's my situation: I have 1) a system image on an a brand new external 1 TB SATA drive, that I managed to successfully capture before my 2) primary system drive went down. I realize this is a fairly simple matter of buying a new primary drive and performing the recovery to the fresh disk...however, the issue is that I believe Win7 was also having some significant issues of its own--basically, Update unable to install updates, and Backup continually ditching the auto backup schedule. I'd been trying to address those issues when my system was still working, but it's been so fruitless, I'm convinced a Win7 re-install would be best, and now I'm concerned that if I was in fact having what I believe are likely registry-related issues before, that these will persist through a recovery--would that likely be correct? I'm mainly worried about recovering my files, so if I did a full recovery from the image, should I be able to then access my individual files, and copy them manually to an external drive, so I can then do a full re-install of Win7? Sory if this seems obvious, but I've never done a recovery before and just trying to make sure there's no red flags with what I have in mind...

  Read the article

• Amazon CloudFront and EC2: Global Load Balancing

  - by Matt Rogish

  We have an app that is going to store and serve up a decent amount of data in S3 to a global audience where latency should be minimized. So, we've been doing tests with Amazon CloudFront and have seen favorable results. However, we need a thin middleware layer (to do security etc.) and we'd like to put that in EC2. Due to security restrictions, this middleware layer will do the file streaming from S3/CloudFront: S3/CloudFront - EC2 - Clients We can geographically distribute the EC2 nodes (US East/West, and Ireland) but the problem is that a client in the EU would hit our US server and be fed data from there, thus rendering much of the performance benefit of CloudFront moot. I've been digging through the EC2 docs but I can't find a built-in way to get a geographically distributed version of EC2 a la CloudFront. Elastic Load Balancing sounds like the way to go, but I can't seem to find a way with that to direct based on routing... Preferably, we'd like to keep the amount of stuff outside of EC2/S3/etc. to a minimum (for obvious reasons). Any ideas how to do that within the EC2/S3 framework? DNS/routing tricks? Thanks!

  Read the article

• Win 2008 R2 - copying TO disk is very slow, copying FROM is more or less okay

  - by avs099

  I have Windows 2008 R2 SP1 with 4 identical SATA disks (Seagate Barracude 7200) in RAID 5 array. It has 4Gb of memory; all recent updates are installed. Problem: when I copy large file from one folder to another, I get about 10MB/s average speed. When I read this file from network share via 1Gbps connection - I get about 25-30 MB/s. Both numbers seems to be low for me - but specifically I'm very frustrated with low write speed. there is no antivirus, no hyper-v, it's just a fileserver - i when i do my tests nobody else reads/write from it (we have only 4 people in a team, so I'm sure). Not sure if that matters, but there is only 1 logic disk "C" with all available space (1400 GB). I'm not an admin at all, so I have no idea where to look and what other information to provide. I did run performance monitor with "% idle time", "avg bytes read", "avg byte write" - here is the screenshot: I'm not sure why there are such obvious spikes. Any idea? Please let me know if you need me to provide more information - what counters should I check, etc. I'm very eager to get this solved. Thank you. UPDATE: we have another Windows 2008 R2 SP1 server with 2 RAID1 arrays - one is disk C (where windows is installed, another one is disk E). It is running Hyper-V and does not have antivirus. I noticed the following behavior when I copy large file (few GBs): C - C: about 50MB/sec C - E: about 55MB/sec E - E: 8MB/sec!!! E - C: 8MB/sec!!! what could cause this?? E drive is RAID1 array from same Seagate Barracuda 1TB drives..

  Read the article

• Where do I define a group policy that will set a users desktop background color to green the first time they log in?

  - by Tyler

  Servers: W2k8 R2 x64 Desktops: Win7 Pro x64 Our current group policy uses a custom ADM file to define certain properties of the desktop (Background Image (centered), Background Color is green (00 74 00)). This policy works for us, but the down-side is that policies defined in our custom ADM are only applied after a GPUpdate /Force is applied. We would like these desktop theme settings to be applied the first time the user logs onto the computer. I've been working on a new policy that forces the computer to wait for the network when the user logs on to handle folder redirection. The reason for writing the new policy was to resolve the issue that a user needs to run GPupdate /Force the first time they log in, so it doesn't make sense for me to implement the new policy if there is still something that requires GPUpdate /Force to get the user in the state that we want them. I've moved the setting for background image out into Admin Templates- Desktop- Desktop- "Desktop Wallpaper" so this is now being set properly when the user first logs in. Now I'm left with a black background until I force a group policy update. I have tried to play around with setting a default "Theme" and had limited success; this was not reliable enough to call a solution. I suppose I could set the background color with a script? Any thoughts? It feels like I'm missing something obvious, or that this should be much easier than it is.

  Read the article

• Problems with word completion on Windows Mobile

  - by Rowland Shaw

  For "some reason" the word completion function on my windows mobile phone (HTC Diamond, rebadged as a T-Mobile MDA Compact IV (UK) running WM6.1 with HTC Touch Flo 3D) hasn't worked since one of my firends was taking a look at the phone (I remember him bitching about it being too obtrusive for him, as an iPhone fanboy). I've checked all the obvious settings ( Start Input Word Completion ) and everything looks set there; I tried a hard reset, to no avail and even tried upgrading the ROM t the latest from my network provider. I even tried walking into the store where I bought the phone, and the staff couldn't fix the issue. I still have my old handset, which also runs WM6.1 (a T-Mobile MDA Compact III (UK), albeit without Touch Flo 3D), and the word completion works on there, so I'm a little confused as to why I can't get it to work again on my new handset. Can anybody identify why this might not be working, or help me fix it? Edit: Even "Touch Input Settings" has both "Word Completion in T9 mode" and "Word Completion in ABC mode" checked. The full qwerty keyboard option is in T9 mode, and word completion works for this input method; It still does not work for my preferred, "Letter Recogniser" method.

  Read the article

• Remote Desktop *from* Windows 2008 R2 Server

  - by freefaller

  Summary: how do I create an RDC connection from a Windows 2008 server to another server? Our client will only allow us to connect to their server via a static IP address (which is fair enough), but unfortunately as we're a very small company we don't have one in the office. As a work around, we had the connection working through our old Windows 2003 server (dynamic-cloud from 1and1). .. however we have just rebuilt the server to run under Windows 2008 R2 (don't ask, but it was necessary), and now I simply cannot get the connection working. I have added an "Outbound Rule" to Windows Firewall with Advanced Security (TCP, All local ports, 3389 remote port - I have also tried the other way around). I have added a packet filter IP security rule with the same details. The 1and1 firewall rules (through their online control panel) allows for 3389 TCP and UDP. But it is simply not connecting (yes, the server is definitely on and able to accept connections) with the general error of... Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Is there anything obvious I've missed - or something I can use to find out where the request is being blocked? The new server is using the exact same IP address as before, so I don't believe that would be an issue. Unless it's trying to use an IPv6 address rather than the old IPv4 address that it was before? I apologise that I am not a network person by trade, but I know more than anybody else in my office!!

  Read the article

• Windows 7: Setting up backup to an external hard drive on another computer on the network

  - by seansand

  I have an external hard drive connected to a Windows 7 (Home Edition) computer. I have another computer (with Windows 7 Ultimate), and I want to have the Windows 7 Ultimate back up to the same external hard drive, without having to disconnect and move the external hard drive from the Home Edition PC. When I get to the "Set up backup" dialog within Windows 7, it asks me where to save the backup. I select "Save on a network". However, when I enter "\\computername\harddrivename" under Browse, the "OK" button remains grayed out. The button remains grayed out unless I also enter a Username and Password under "Network credentials". However, the account I have on the other computer doesn't have a password for it. To un-gray out the button I must enter a fake password, allowing me to click "OK", but then obviously I get a "bad password" error. Does anyone know how to get around this problem? (Seems kind of ridiculous.) I made sure that the security settings with the external hard drive on the other computer are full access to Everyone, so permissions is not the problem. I also thought about using Homegroup instead of the regular security settings, but there is no obvious way to go about it that way, either.

  Read the article

• CryptSvc not matched by Windows 7 Firewall rule

  - by theultramage

  I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

  Read the article

• Surprising corruption and never-ending fsck after resizing a filesystem.

  - by Steve Kemp

  System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

  Read the article

• is it good to have or difference between ADSL Modem+WiFi Router and Separate ADSL Modem & Wi-Fi Router?

  - by vikas devde

  I have ADSL2 Modem which I got from my service provider, now I want to setup wireless(Wi-Fi) in my home. I went to shop, where I came to know that there are routers which come up with modem also but they are priced lil higher than the only wi-fi routers. Now it is obvious that I should go for only wi-fi one, as I already have modem. My question is, is there any difference between ADSL+router and only router? I think if I use ADSL+router, the speed will increase lilbit, as modem does modulate and demodulate signals, and router also generates wireless signal, that is time to take conversions is doubled, and if I use ADSL+modem, it will directly convert the signals to wireless, and time will be saved, so the overall speed will increase lilbit. This is what my concept is(Which might be wrong). What do you guys would suggest me? should I take my current modem away and buy an ADSL+router or I should keep my modem and buy only wi-fi one. Please tell me the difference and suggest me which one I should go with, and also suggest me which company router I should go for.

  Read the article

• Why do I often have to refresh pages I navigate to once for them (or content in them) to load?

  - by GetOutOfBox

  I have noticed a bizarre pattern when using my PC, that when I open a link to a website, it often will often take a very long time to load, or time out. Sometimes content on the website will be drawn, but again, it seems to get "stuck" for an unusual amount of time before finishing. Most affected is Youtube; almost every time I navigate to a youtube video from another website such as Google, the video will not begin playing, but will instead just display the player controls with a black screen where the video should be and the buffering symbol, usually before displaying an error such as "The video failed to load". The unusual part of this problem is that whenever this happens, refreshing the page always causes it to load almost immediately the second time around, without any problems. Note that I'm not talking about how some browsers will dump whatever has been cached to the "pallet" briefly when the page is refreshed or loading stopped; but that the second time loading the website being faster. I have done my best to rule out some of the obvious causes: My Windows 7 desktop computer is the only device that seems to be affected. I use Firefox on it (latest version, flash updated, etc). My connection has more than enough bandwidth (30 megabits down, 4 up), and I've even tried QoSing all other devices to make sure this isn't happening due to usage spikes. Wireshark is not showing any clearly unusual network activity (i.e frequently dropped packets).

  Read the article

• DPM 2007 clashing with existing SQL backup job

  - by Paul D'Ambra

  I've recently installed a DPM2007 server on Server 2003 and have set up a protection group against a server 2003 server running SQL 2005 SP3. The SQL server in question has a full backup (as a sql agent job) once a day and transaction log backups hourly. These are zipped up and FTP'd to a server offsite by a scheduled task. Since adding the DPM job I'm receiving many error messages: DPM tried to do a SQL log backup, either as part of a backup job or a recovery to latest point in time job. The SQL log backup job has detected a discontinuity in the SQL log chain for database SERVER_NAME\DB_Name since the last backup. All incremental backup jobs will fail until an express full backup runs. My google-fu suggests that I need to change the full backup my sqlagent job is running to a copy_only job. But I think this means that I can't use that backup with the transaction_logs to restore the database if the building (including the DPM server) burns down. I'm sure I'm missing something obvious and thought I'd see what the hivemind suggests. It is an option to set-up a co-located DPM server elsewhere and have DPM stream the backup but that's obviously more expensive than the current set up. Many thanks in advance

  Read the article

• Apache 2 Fails to Start After Upgrade with No Errors

  - by Mark Davidson

  Hi all Hoping someone can help me with a server issue. Recently we upgraded to the latest apache on 2 boxes within are organisation. One being the master box the other being for failover. The upgrade went fine on the master box but on the failover box apache fails to start with no errors, being output or logged. Both boxes have the exact same configuration so found this a bit strange. I've reinstalled apache and have been through checking the configs and did not find any obvious errors. Eventally I ran a syntax check on each config file being included and found that one of the files apparently has syntax errors. Invalid command 'Order', perhaps misspelled or defined by a module not included in the server configuration Invalid command 'php_value', perhaps misspelled or defined by a module not included in the server configuration Invalid command 'GeoIPEnable', perhaps misspelled or defined by a module not included in the server configuration I've trippled checked all the modules are enabled but it still fails. I've googled the subject of these errors loads but have been unable to fine a solution. I was wondering if anyone had encountered such a problem before and could point me towards a solution. Thanks for your help in advance. P.s: Apache related versions on server. ii apache2 2.2.3-4+etch10 Next generation, scalable, extendable web se ii apache2-mpm-prefork 2.2.3-4+etch10 Traditional model for Apache HTTPD 2.1 ii apache2-utils 2.2.3-4+etch10 utility programs for webservers ii apache2.2-common 2.2.3-4+etch10 Next generation, scalable, extendable web se ii libapache2-mod-geoip 1.1.8-2 GeoIP support for apache2 ii libapache2-mod-php5 5.2.0+dfsg-8+etch15 server-side, HTML-embedded scripting languag

  Read the article

• eXist-db: can't start webstart client on a closed port, reverse proxied via apache

  - by rvdb

  I am configuring an Apache HTTP server so it reverse proxies requests starting with /app/ to an eXist-db instance running in a Tomcat server, on port 8082. This port has been closed in the firewall and is inaccessible to the outer world. Following the eXist documentation, I have following rules in place in my httpd.conf file: ProxyPass /apps/ http://localhost:8082/ ProxyPassReverse /apps/ http://localhost:8082/ ProxyPassReverseCookiePath /apps/ / All goes well for requests to e.g. 'http://mydomain/apps/exist/index.xml'. Yet, the webstart client (accessible at 'http://localhost:8082/exist/webstart/exist.jnlp' on the web server) doesn't work behind the proxy. While 'http://mydomain/apps/exist/webstart/exist.jnlp' does generate a valid exist.jnlp file, that file can't be executed. The reason seems quite obvious: apparently, the eXist-db instance generating the exist.jnlp file only sees the proxied request as: 'http://localhost:8082/exist/webstart/exist.jnlp'. Yet, since the exist.jnlp file is executed on the client, that reference is meaningless (unless the client computer happens to have an eXist-db instance running on that port). Executing the exist.jnlp file hence fails with a 'connection refused' error. Yet, there's no problem at all connecting a local eXist-db Java client to the proxied eXist instance with the URL xmldb:exist://mydomain/apps/exist/xmlrpc. The problem lies in generating the webstart exist.jnlp file, which seems to need access to a publicly accessible URL. However, opening port 8082 and replacing the Proxy references to 'http://localhost:8082' with 'http://mydomain:8082' IMO rather destroys the point of reverse proxying. Do others have had success reverse proxying eXist-db on a closed port behind Apache? Are there perhaps some Proxy configuration settings I have overlooked (I'm no expert at all) that can make eXist see the original request instead of the proxied one? Kind regards, Ron

  Read the article

• Best photo management software?

  - by Niels Basjes

  Hi, What I would like is a single piece of software (or a smart combination of tools) that allow me to manage my photos in a better way than what I've found so far. 1. Tags Primarily I need a way of tagging the images. So I can manually tag photos the same way we tag questions here at SO/SF/SU. I want this software to place a lot of the tags automagically (obvious things like date and resolution). 2. Face recognition What I would really like is that this software has a feature that it can recognize faces in images and places tags with the name of the person. So far I've only heard of one online photo system that can do that (Picasa) and not yet of any offline tool. 3. Version database I must have some way of having a central GIT/SVN/... that contains all images. I have had a harddrive corruption a few years ago and it took me a long time to figure out which images had been damaged. I always want to be able to go back to what the camera produced. 4. Website I want to be able to generate a website (few 'tag' specific websites) based on the actual content. 5. Easy bulk uploading Many photo tools have a one on one uploading option. I prefer simply 'throwing' my images on a file server under Linux (Samba) and let the system automagically integrate, tag, recognize, etc. all images. Ok, I know these are a bit much. Perhaps you guy's have some suggestions about existing tools that can make this possible. Or even a complete system that does this. EDIT: To clarify on the OS. I prefer Linux for any 'server' task and Windows XP for any 'desktop' task. Thanks for all your input. Niels Basjes

  Read the article

< Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >