Search Results

Search found 9471 results on 379 pages for 'mac'.

Page 363/379 | < Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >

• Download - Upload is too slow on Centos

  - by Mehdi

  My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

  Read the article

• Tomcat with virtual hosts - 404

  - by Thardas

  I have a CentOS 5.2 server set up with Apache 2.2.3 and Tomcat 5.5.27. The server hosts multiple virtual hosts connected to multiple Tomcats. For instance we have one tomcat for development and testing and one tomcat for production. project.demo.us.com points to dev tomcat and project.us.com points to production tomcat. Here's the virtual host's configuration: <VirtualHost *:80> ServerName project.demo.us.com CustomLog logs/project.demo.us.com/access_log combined env=!VLOG ErrorLog logs/project.demo.us.com/error_log DocumentRoot /var/www/vhosts/project.demo.us.com <Directory /var/www/vhosts/project.demo.us.com> Allow from all AllowOverride All Options -Indexes FollowSymLinks </Directory> ########## ########## ########## JkMount /project/* online </VirtualHost> JkMount line defines that we use online worker and our workers.properties contains this: worker.list=..., online, ... worker.online.port=7703 worker.online.host=localhost worker.online.type=ajp13 worker.online.lbfactor=1 And tomcat's conf/server.xml contains: <Connector port="7703" enableLookups="false" redirectPort="8443" protocol="AJP/1.3" URIEncoding="UTF-8" maxThreads="80" minSpareThreads="10" maxSpareThreads="15"/> I'm not sure what redirectPort is but I tried to telnet to that port and there's no one answering, so it shouldn't matter? Tomcat's webapps directory contains project.war and the server automatically deployed it under project directory which contains index.jsp and hello.html. The latter is for static debugging purposes. Now when I try to access http://project.demo.us.com/project/index.jsp, I get Tomcat's HTTP Status 404 - The requested resource () is not available. The same thing happens to hello.html so it's not working with static content either. Apache's access_log contains: 88.112.152.31 - - [10/Aug/2009:12:15:14 +0300] "GET /demo/index.jsp HTTP/1.1" 404 952 "-" "Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2" I couldn't find any mention of the request in Tomcat's logs. If I shutdown this specific tomcat, I no longer get Tomcat's 404 but Apache's 503 Service Temporarily Unavailable, so I should be configuring the correct Tomcat. Is there something obvious that I'm missing? Is there any place where I could find out what path the Tomcat is using to look for requested files?

  Read the article

• Log - Server kernel: INFO: task httpd:000000 blocked for more than 120 seconds

  - by valter

  Almost everyday my server is crashing due to hight server load, and even restarting apache or mysql can't solve the problem. I need to reboot the server to solve, or it crash again due to the high load. The log system records something like this when it crashes: Aug 11 18:33:53 server kernel: INFO: task httpd:20008 blocked for more than 120 seconds. Aug 11 18:33:53 server kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 11 18:33:53 server kernel: httpd D ffffffff801538ac 0 20008 5816 20066 19809 (NOTLB) Aug 11 18:33:53 server kernel: ffff81025a299dc8 0000000000000082 ffff81033b4c0740 ffffffff80009a14 Aug 11 18:33:53 server kernel: ffff8101063f8d80 0000000000000009 ffff8100b758f7e0 ffff8101c57187e0 Aug 11 18:33:53 server kernel: 00009436d4100b6c 000000000001d50f ffff8100b758f9c8 000000083b531588 Aug 11 18:33:53 server kernel: Call Trace: Aug 11 18:33:53 server kernel: [<ffffffff80009a14>] __link_path_walk+0x173/0xfb9 Aug 11 18:33:53 server kernel: [<ffffffff8002cc16>] mntput_no_expire+0x19/0x89 Aug 11 18:33:53 server kernel: [<ffffffff80063c4f>] __mutex_lock_slowpath+0x60/0x9b Aug 11 18:33:53 server kernel: [<ffffffff80023908>] __path_lookup_intent_open+0x56/0x97 Aug 11 18:33:53 server kernel: [<ffffffff80063c99>] .text.lock.mutex+0xf/0x14 Aug 11 18:33:53 server kernel: [<ffffffff8001b21f>] open_namei+0xea/0x712 Aug 11 18:33:54 server kernel: [<ffffffff8002768a>] do_filp_open+0x1c/0x38 Aug 11 18:33:54 server kernel: Firewall: *UDP_IN Blocked* IN=eth1 OUT= MAC=ff:ff:ff:ff:ff:ff:00:30:48:9e:6e:99:08:00 SRC=208.43.135.158 DST=255.255.255.255 LEN=151 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=38354 DPT=6112 LEN=131 Aug 11 18:33:54 server kernel: [<ffffffff8001a061>] do_sys_open+0x44/0xbe Aug 11 18:33:54 server kernel: [<ffffffff8005d28d>] tracesys+0xd5/0xe0 I googled a lot trying to find a solution. But it looks that the solution is just to update the kernel or disk driver, thinks that I don't know how to do. In this url http://bugs.centos.org/view.php?id=4515 a lot o people report similar problems, except the fact that they are not related to httpd like mine. According to one member, one solution would be to add "elevator=noop " to /etc/grub.conf like in this example: title CentOS (2.6.18-238.12.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-238.12.1.el5xen ro root=/dev/VolGroup00/LogVol00 elevator=noop initrd /initrd-2.6.18-238.12.1.el5xen.img Would this really solve the problem? My disk are working in RAID. Can this cause some problem to my server? Is there any other solution?

  Read the article

• iCloud stuff stops working while connected to OpenVPN [closed]

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

  Read the article

• Vagrant reporting VirtualBox guest additions out of date

  - by DTest

  Fairly new to Vagrant, so bear with me if I don't understand the process. I downloaded a CentOS box off http://www.vagrantbox.es/ Started it up running VirtualBox 4.2.4 and got this message: [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 So I used the vbguest plugin to update the guest additions, then repackaged the box as suggested. Having replaced the old box and loading it up I get the same message about guest additions being outdated, but vbguest reports that they are up to date (the automatic vbguest update is disabled in my Vagrantfile): Vagrant::Config.run do |config| config.vm.box = "centos56_64" config.vbguest.auto_update = false config.vbguest.no_remote = true end And the commands: dtest$ vagrant up [default] Importing base box 'centos56_64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- 22 => 2222 (adapter 1) [default] Creating shared folders metadata... [default] Clearing any previously set network interfaces... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant dtest$ vagrant vbguest --no-install [default] Detected Virtualbox Guest Additions 4.2.4 --- OK. [default] Virtualbox Guest Additions on host: 4.2.4 - guest's version is 4.2.4 Since they appear to be updated after an install, I could ignore the message. But is it possible to get rid of it?

  Read the article

• Ubuntu box static routing problem

  - by Rafael

  Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

  Read the article

• Email server can send internal, but messages never arrive at external recipients

  - by Chase Florell

  I'm running MailEnable on my server, and have been for many years. Recently we had an attack on our server, and I was able to close the hole. Since then, our mail server doesn't seem to be sending mail out. If I send an email from myself to another account hosted on the server, the email arrives as expected. If I send an email from my gmail account to my business account, the email also arrives as expected The problem comes when I send from my business account to an external domain I tried the following Gmail.com Hotmail.com Shaw.ca When I send to any of the above The message leaves my client as expected, The logs appear to accept and forward on the message The SMTP outbound que is empty The message never arrives I have checked our domain with mxtoolbox.com senderbase.org And neither of them are reporting any problems with our domain. I have ensured that port 25 is open (along with the other standard ports) Here is one of the log entries from the SMTP connector 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 220 mx1.example.com ESMTP MailEnable Service, Version: 6.81--6.81 ready at 11/05/13 12:10:00 0 0 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH AUTH LOGIN 334 VXNlcm5hbWU6 18 12 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH {blank} 334 UGFzc3dvcmQ6 18 26 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH Y29sb25lbGZhY2U= 235 Authenticated 19 18 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 MAIL MAIL FROM:<[email protected]> 250 Requested mail action okay, completed 43 31 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 RCPT RCPT TO:<[email protected]> 250 Requested mail action okay, completed 43 35 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 DATA DATA 354 Start mail input; end with <CRLF>.<CRLF> 46 6 [email protected] Here are the headers of the sent message X-Assp-Version: 1.7.5.7(1.0.07) on ASSP.nospam X-Assp-ID: ASSP.nospam 78601-04523 X-Assp-Intended-For: [email protected] X-Assp-Envelope-From: [email protected] Received: from [10.10.1.101] ([68.147.245.149] helo=[10.10.1.101]) with IPv4:587 by ASSP.nospam; 5 Nov 2013 12:10:00 -0700 From: Chase Florell <[email protected]> Content-Type: text/plain Content-Transfer-Encoding: 7bit Subject: Test Message Message-Id: <[email protected]> Date: Tue, 5 Nov 2013 12:10:18 -0700 To: Chase Florell <[email protected]> Mime-Version: 1.0 (Mac OS X Mail 7.0 \(1816\)) X-Mailer: Apple Mail (2.1816) . Where else can I check to see if there is something broken? What could cause a problem like this whereby the message appears to send, but never arrives, and never returns a bounce?

  Read the article

• "vagrant up" fails with "NS_ERROR_CALL_FAILED" error [on hold]

  - by TahitiPetey

  I am following the basic "Getting Started" guide: http://docs.vagrantup.com/v2/getting-started/index.html I ran vagrant init <etc> followed by vagrant up, but it fails with "NS_ERROR_CALL_FAILED" error. Then by enabling debug logging with VAGRANT_LOG=debug vagrant up, I get the following error output: ERROR vagrant: /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/driver/base.rb:316:in `execute' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/driver/version_4_2.rb:165:in `import' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/import.rb:15:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/handle_box_url.rb:72:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/check_accessible.rb:18:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `block in run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/util/busy.rb:19:in `busy' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/call.rb:51:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/config_validate.rb:25:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/check_virtualbox.rb:17:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builder.rb:116:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `block in run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/util/busy.rb:19:in `busy' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/machine.rb:147:in `action' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/batch_action.rb:63:in `block (2 levels) in run' INFO interface: error: There was an error while executing `VBoxManage`, a CLI used by Vagrant for controlling VirtualBox. The command and stderr is shown below. Command: ["import", "/Users/me/.vagrant.d/boxes/precise32/virtualbox/box.ovf"] Stderr: 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% Interpreting /Users/me/.vagrant.d/boxes/precise32/virtualbox/box.ovf... OK. 0%... Progress object failure: NS_ERROR_CALL_FAILED My system setup info: Vagrant 1.2.2 VirtualBox 4.2.14 (Also tried 4.2.10, same error) Mac OSX 10.8.3

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubu

  - by user37968

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Passenger 2.2.4, nginx 0.7.61 and SSL

  - by boompa

  Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Authenticate to VM using vagrant up

  - by utrecht

  Authentication failure during Vagrant Up, while vagrant ssh and ssh vagrant@localhost -p2222 works I would like to execute a shell script using Vagrant at boot. Vagrant is unable to Authenticate, while the VM has been started using vagrant up: c:\temp\helloworld>vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Importing base box 'helloworld'... ==> default: Matching MAC address for NAT networking... ==> default: Setting the name of the VM: helloworld_default_1398419922203_60603 ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2222 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2222 default: SSH username: vagrant default: SSH auth method: private key default: Error: Connection timeout. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... ... After executing CTRL + C it is possible to authenticate to the VM using vagrant ssh and ssh vagrant@localhost -p2222 Vagrant file I use the default Vagrantfile and I only changed the hostname: # -*- mode: ruby -*- # vi: set ft=ruby : # Vagrantfile API/syntax version. Don't touch unless you know what you're doing! VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| # All Vagrant configuration is done here. The most common configuration # options are documented and commented below. For a complete reference, # please see the online documentation at vagrantup.com. # Every Vagrant virtual environment requires a box to build off of. config.vm.box = "helloworld" ... Vagrant version c:\temp\helloworld>vagrant --version Vagrant 1.5.1 Question How to authenticate to VM using vagrant up?

  Read the article

• Updating the $PATH for running an command through SSH with LDAP user account

  - by Guillaume Bodi

  Hi all, I am setting up a Mac OSX 1.6 server to host Git repositories. As such we need to push commits to the server through SSH. The server has only an admin account and uses a user list from a LDAP server. Now, since it is accessing the server through a non interactive shell, git operations are not able to complete since git executables are not in the default path. As the users are network users, they do not have a local home folder. So I cannot use a ~/.bashrc and the like solution. I browsed over several articles here and there but could not get it working in a nice and clean setup. Here are the infos on the methods I gathered so far: I could update the default PATH environment to include the git executables folder. However, I could not manage to do it successfully. Updating /etc/paths didn't change anything and since it's not an interactive shell, /etc/profile and /etc/bashrc are ignored. From the ssh manpage, I read that a BASH_ENV variable can be set to get an optional script to be executed. However I cannot figure how to set it system wide on the server. If it needs to be set up on the client machine, this is not an acceptable solution. If someone has some info on how it is supposed to be done, please, by all means! I can fix this problem by creating a .bashrc with PATH correction in the system root (since all network users would start here as they do not have home). But it just feels wrong. Additionally, if we do create a home folder for an user, then the git command would fail again. I can install a third party application to set up hooks on the login and then run a script creating a home directory with the necessary path corrections. This smells like a backyard tinkering and duct tape solution. I can install a small script on the server and ForceCommand the sshd to this script on login. This script will then look for a command to execute ($SSH_ORIGINAL_COMMAND) and trigger a login shell to run this command, or just trigger a regular login shell for an interactive session. The full details of this method can be found here: http://marc.info/?l=git&m=121378876831164 The last one is the best method I found so far. Any suggestions on how to deal with this properly?

  Read the article

• CentOS 5.8 dig is not resolving ip-address

  - by travisbotello

  I'm running centos 5.8 on a local machine at home. Today I was trying to analyze the DNS-Lookup via dig. $ dig +trace -t A www.heise.de. This is giving me something like this as a response de. 172800 IN NS f.nic.de. de. 172800 IN NS z.nic.de. de. 172800 IN NS s.de.net. de. 172800 IN NS n.de.net. de. 172800 IN NS a.nic.de. de. 172800 IN NS l.de.net. ;; Received 344 bytes from 192.58.128.30#53(192.58.128.30) in 49 ms In contrast my dedicated CentOS machine is returning the following de. 172800 IN NS a.nic.de. de. 172800 IN NS n.de.net. de. 172800 IN NS f.nic.de. de. 172800 IN NS z.nic.de. de. 172800 IN NS l.de.net. de. 172800 IN NS s.de.net. ;; Received 344 bytes from 192.58.128.30#53(j.root-servers.net) in 32 ms As you can see, the last line is different. Any idea why my dedicated machine is giving me the host name of the responding DNS-Server and my local machine is only returning the ip-address? Thanks in advance UPDATE The reverse DNS-Lookup is working without any problems. Also, I just checked this on my local mac and...exactly the same problem occurs. Is it possible that this has to do with the local router/modem/ISP?

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

  - by larsks

  I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• Vim configuration slow in Terminal & iTerm2 but not in MacVim

  - by Jey Balachandran

  Ideally, I want to use Vim from Terminal or iTerm2. However, it becomes unbearably slow so I had to resort to using MacVim. There is nothing wrong with MacVim, however my workflow would be much smoother if I used only Terminal/iTerm2. When its slow Loading files, in particular Rails files takes about 1 - 1.5s. Removing rails.vim decreases this time to 0.5 - 1s. In MacVim this is instantaneous. Scrolling through the rows and columns via h, j, k, l. It progressively gets slower the longer I hold down the keys. Eventually, it starts jumping rows. I have my Key Repeat set to Fast and Delay Until Repeat set to Short. After 10 - 15 minutes of usage, using plugins such as ctrlp or Command-T gets very laggy. I'd type a letter, wait 2 - 3s, then type the next. My Setup 11" MacBook Air running Mac OS X Version 10.7.3 (1.6 Ghz Intel Core 2 Duo, 4 GB DDR3) My dotfiles. > vim --version VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Nov 16 2011 16:44:23) MacOS X (unix) version Included patches: 1-333 Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv -cscope +cursorbind +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme +netbeans_intg +path_extra -perl +persistent_undo +postscript +printer +profile +python -python3 +quickfix +reltime +rightleft +ruby +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/local/Cellar/vim/7.3.333/share/vim" Compilation: /usr/bin/llvm-gcc -c -I. -Iproto -DHAVE_CONFIG_H -DMACOS_X_UNIX -no-cpp-precomp -O3 -march=core2 -msse4.1 -w -pipe -D_FORTIFY_SOURCE=1 Linking: /usr/bin/llvm-gcc -L. -L/usr/local/lib -o vim -lm -lncurses -liconv -framework Cocoa -framework Python -lruby I've tried running without any plugins or syntax highlighting. It opens files a lot faster but still not as fast as MacVim. But the other two problems still exist. Why is my vim configuration slow? How can I improve the speed of my vim configuration within Terminal or iTerm2?

  Read the article

• Is Samba Server what I'm looking for, and if so, what do I need? (currently on DD-WRT Micro)

  - by Anthony

  I am really confused as to what Samba actually does and how it works. Here's what I'm hoping it does: I set up a Samba server on my LAN, and everyone will be able to see each other's shared files and swap them. But some of the documentation makes it sound like it will just allow Mac/Linux computers to see Windows computers. Other bits of the documentation make it sound more like a local server, where a Linux machine would install Samba and they would see everyone and be visible to everyone, but that won't change if anybody else can see each other. While still other things I've read make it seem more like a file-server, where everyone sees each other but file transfers are not peer-to-peer but instead need a host disk for files to act as go between. So, assuming I'm even in the right ballpark of what Samba does in terms of my goal of total cross-visibility on the network, I am left with needing to know what I'd need to set up the server and whether it can be done and is worth it... DD-WRT's article on Samba is a bit ambiguous. One second it sounds as if I can run the server on micro as long as it's set up on a usb drive, but then it also sounds like micro can't run it at all, etc. If I can run it from a usb-connected drive, I still need to know if the files are actually stored on that drive. The dd-wrt article mentions: You can run a Samba server on your main computer and run a client on your router (thus gaining writable storage for the router) or you can use Samba to share a drive connected (typically by USB) to the router among all the computers connected to your network. That one part "to share a drive...among all the computers" makes it sound like the only benefit I get from Samba is a share drive that any OS on the network can see, but they still won't see each other. But I'm very hopeful I'm misreading this. If the computers can see each other but still need the disk, how much space is generally a good idea? I'm basing this on the idea that the drive is a temporary store point. Obviously I'd have to get a drive big enough to store everything people wanted to share if the drive is a full-on file server. If I do have this all wrong, is there any software that achieves what I have in mind? Something that connects to the main router to bridge all clients?

  Read the article

• Pxe net install Centos with Static IP

  - by Stu2000

  I seem to be unable to perform a kickstart installation of centos5.8 with a netinstall. It correctly gets into the text installer, but keeps sending out a request for the dhcp server and failing. I have tried to manually set the IP everywhere. Here is my pxelinux.cfg file DEFAULT menu PROMPT 0 MENU TITLE Ubuntu MAAS TIMEOUT 200 TOTALTIMEOUT 6000 ONTIMEOUT local LABEL centos5.8-net kernel /images/centos5.8-net/vmlinuz MENU LABEL centos5.8-net append initrd=/images/centos5.8-net/initrd.img ip=192.168.1.163 netmask=255.255.255.0 hostname=client101 gateway=192.168.1.1 ksdevice=eth0 dns=8.8.8.8 ks=http://192.168.1.125/cblr/svc/op/ks/profile/centos5.8-net MENU end and here is my kickstart file: # Kickstart file for a very basic Centos 5.8 system # Assigns the server ip: 192.211.48.163 # DNS 8.8.8.8, 8.8.4.4 # London TZ install url --url http://mirror.centos.org/centos-5/5.8/os/i386 lang en_US.UTF-8 keyboard us network --device=eth0 --bootproto=static --ip=192.168.1.163 --netmask=255.255.255.0 --gateway=192.168.1.1 --nameserver=8.8.8.8,8.8.4.4 --hostname=client1-server --onboot=on rootpw --iscrypted $1$Snrd2bB6$CuD/07AX2r/lHgVTPZyAz/ firewall --enabled --port=22:tcp authconfig --enableshadow --enablemd5 selinux --enforcing timezone --utc Europe/London bootloader --location=mbr --driveorder=xvda --append="console=xvc0" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work part /boot --fstype ext3 --size=100 --ondisk=xvda part pv.2 --size=0 --grow --ondisk=xvda volgroup VolGroup00 --pesize=32768 pv.2 logvol swap --fstype swap --name=LogVol01 --vgname=VolGroup00 --size=528 --grow --maxsize=1056 logvol / --fstype ext3 --name=LogVol00 --vgname=VolGroup00 --size=1024 --grow %packages @base @core @dialup @editors @text-internet keyutils iscsi-initiator-utils trousers bridge-utils fipscheck device-mapper-multipath sgpio emacs Here is my dhcp file: ddns-update-style interim; allow booting; allow bootp; ignore client-updates; set vendorclass = option vendor-class-identifier; subnet 192.168.1.0 netmask 255.255.255.0 { host tower { hardware ethernet 50:E5:49:18:D5:C6; fixed-address 192.168.1.163; option routers 192.168.1.1; option domain-name-servers 8.8.8.8,8.8.4.4; option subnet-mask 255.255.255.0; filename "/pxelinux.0"; default-lease-time 21600; max-lease-time 43200; next-server 192.168.1.125; } } Is it impossible to prevent it asking for a dynamic ip before trying to install from the net? Perhaps there is an error in of my files? My dhcp server is set to ignore client-updates, and is set to only works with one mac address whilst testing.

  Read the article

• Troubleshooting an NFS server hanging after authenticated mount request

  - by Christoph

  I need some advice on troubleshooting an NFS server problem on Scientific Linux (RHEL) 6.1. The log on the server shows that an authenticated mount request was made: Jan 13 16:30:02 ??? rpc.mountd[3996]: authenticated mount request from ????:784 for /shared-storage/cm/shared (/shared-storage/cm/shared) But after that, it does not continue. On the client, it is also hanging. The interesting thing now is that I have two NFS servers, which should be identical, and the one is working perfectly, but the other exhibits the above mentioned behaviour. The problem is also not completely persistent, i. e. sometimes the mount request succeeds. I assume that the problem must be related to the server rather than to the client, because it is working perfectly on the other server. My question is where I should search the problem. I have already re-created the exports using exportfs -r, I have restarted the NFS server, I have compared the rpcinfo outputs of both server - no success. The problem even survives a reboot. Any other ideas are appreciated. As answer to Tim's question: I have sporadically the following in dmesg, but do not know whether it is related e1000e 0000:0c:00.0: eth4: Detected Hardware Unit Hang: TDH <24> TDT <25> next_to_use <25> next_to_clean <24> buffer_info[next_to_clean]: time_stamp <1c3d12940> next_to_watch <24> jiffies <1c3d12940> next_to_watch.status <0> MAC Status <80383> PHY Status <792d> PHY 1000BASE-T Status <7800> PHY Extended Status <3000> PCI Status <10> Further edit: The problem above does not occur on the machine that is working, so it probably is related. Again an edit: The error is not on the (software) device that is used for NFS, but on another one. The NFS mount also does not trigger the message.

  Read the article

• EMC/Legato/Networker Failed to recover files : Cross Platform Recovery not supported.

  - by marc.riera

  Software used to backup: EMC / Legato Networker legato server : windows legato clients: same hardware (2 years ago fedora something , now ubuntu ) Trying to recover from an old client, which is no longer available. So this is the thing. On 07/20/2008 we backed up a samba server(fedora something) to a tape , setting 1 year as browse policy and retention policy. Now this tape is recyclable. We took down the dns name. We deleted the legato client configuration. That legato client was reinstalled and is doing other stuff on ubuntu 10.04, with a different name but same ip. Now, 2 years and some month later #### Now we need to recover a folder from 2008 backup, on the fedora-samba-server. First thing, legato does not show the client name because the config was deleted. We create it again. We just set the old dns back on track, pointing the same ip, where the old server was, same MAC address ;). We created a new 'old client configuration' pointing to the new server. (different legato ip for client "I suppose" ) The ssid where the needed folder is on 2 tapes, 20 and 22. The index for that backup is on tape 21. We put this tapes on the jukebox (IBMT4000) -- not important for the issue -- All three tapes expired its browsable and recoverable time. So they are on recyclable. We get the clone id from the ssid with following command: mminfo -avot -q "ssid=<ssid>" -r cloneid We set the tapes to notrecyclable nsrmm -S <ssid>/<cloneid> -o notrecyclable We change the retention for the tapes for a future date nsrmm -S <ssid> -e 01/20/2011 We check the dates are correct : mminf -avV -q "ssid=<ssid>" -r ssbrowse(26),ssretent(26),savetime So far its OK. We close the terminal. Restart the server, just for being sure. Finally, we recover the index for that ssid where the folder should be. nsrck -L7 -t "07/20/2008" oldservername.domain.org There, we open the Networker User, select the server, select the old client as source, select the new client as destination. And this is what I get. imgur image of output -- http://i.imgur.com/1nOr8.png Should I understand that I need to install whatsoever operating system that was running on the old "linux server"/"networker client" to be able to restore 26Mb of files? thanks

  Read the article

• What are incentives (if any) to use WinRT instead of .Net?

  - by Ark-kun

  Let's compare WinRT with .Net .Net .Net is the 13+ years evolution of COM. Three main parts of .Net are execution environment, standard libraries and supported languages. CLR is the native-code execution environment based on COM .Net Framework has a big set of standard libraries (implemented using managed and native code) that can be used from all .Net languages. There are .Net classes that allow using OS APIs. WPF or Silverlight provide a XAML-based UI framework .Net can be used with C++, C#, Javascript, Python, Ruby, VB, LISP, Scheme and many other languages. C++/.Net is a variation of the C++ language that allows interaction with .Net objects. .Net supports inheritance, generics, operator and method overloading and many other features. .Net allows creating apps that run on Windows (XP, 7, 8 Pro (Desktop and Metro), RT, CE, etc), Mac OS, Linux (+ other *nix); iOS, Android, Windows Phone (7, 8); Internet Explorer, Chrome, Firefox; XBox 360, Playstation Suite; raw microprocessors. There is support for creating games (2D/3D) using any managed language or C++. Created by Developer Division WinRT WinRT is based on COM. Three main parts of WinRT are execution environment, standard libraries and supported languages. WinRT has a native-code execution environment based on COM WinRT has a set of standard libraries that more or less can be used from WinRT languages. There are WinRT classes that allow using OS APIs. Unnamed Silverlight clone provides a XAML-based UI framework WinRT can be used with C++, C#, Javascript, VB. C++/CX is a variation of the C++ language that allows interaction with WinRT objects. Custom WinRT components don't support inheritance (classes must be sealed), generics, operator overloading and many other features. WinRT allows creating apps that run on Windows 8 Pro and RT (Metro only); Windows Phone 8 (limited). There is support for creating games (2D/3D) using C++ only. Ordered by Windows Team I think that all the aspects except the last ones are very important for developers. On the other hand it seems that the most important aspect for Microsoft is the last one. So, given the above comparison of conceptually identical technologies, what are incentives (if any) to use WinRT instead of .Net?

  Read the article

< Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >